ASROCK 980DE3/U3S3 Kullanım kılavuzu

1

ASRock 980DE3/U3S3 R2.0 Motherboard

English

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documentation

by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identica-

tion or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commit-

ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may

appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or tness for a particular purpose. In no event shall ASRock, its

directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or

consequential damages (including damages for loss of prots, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the pos-

sibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published September 2014

Copyright

©

2

ASRock 980DE3/U3S3 R2.0 Motherboard

English

Motherboard Layout

1 ATX 12V Power Connector (ATX12V1) 20 SATA2 Connector (SATA2_1 (PORT 1))

2 Power Fan Connector (PWR_FAN1) 21 USB 2.0 Header (USB6_7)

3 CPU Fan Connector (CPU_FAN1) 22 USB 2.0 Header (USB4_5)

4 AM3+ CPU Socket 23 USB 2.0 Header (USB8_9)

5 CPU Heatsink Retention Module 24 System Panel Header (PANEL1)

6 2 x 240-pin DDR3 DIMM Slots 25 Power LED Header (PLED1)

(Dual Channel: DDR3_A1, DDR3_B1) 26 Chassis Speaker Header (SPEAKER1)

7 2 x 240-pin DDR3 DIMM Slots 27 Floppy Connector (FLOPPY1)

(Dual Channel: DDR3_A2, DDR3_B2) 28 Internal Audio Connector (CD1)

8 Northbridge Controller 29 Front Panel Audio Header (HD_AUDIO1)

9 SATA3 Connector (SATA3_2 (PORT 7)) 30 HDMI_SPDIF Header (HDMI_SPDIF1)

10 ATX Power Connector (ATXPWR1) 31 Infrared Module Header (IR1)

11 SATA3 Connector (SATA3_1 (PORT 6)) 32 PCI Slots (PCI1-2)

12 Chassis Fan Connector (CHA_FAN1) 33 PCI Express 2.0 x1 Slot (PCIE4)

13 Southbridge Controller 34 PCI Express 2.0 x16 Slot (PCIE3)

14 SPI Flash Memory (16Mb) 35 PCI Express 2.0 x1 Slot (PCIE2)

15 SATA2 Connector (SATA2_6 (PORT 5)) 36 IDE1 Connector (IDE1)

16 SATA2 Connector (SATA2_5 (PORT 4)) 37 PCI Express 2.0 x1 Slot (PCIE1)

17 SATA2 Connector (SATA2_4 (PORT 3)) 38 Clear CMOS Jumper (CLRCMOS1)

18 SATA2 Connector (SATA2_3 (PORT 2)) 39 USB 3.0 Header (USB3_2_3)

19 SATA2 Connector (SATA2_2 (PORT 1))

6

7

1

2

4

3

5

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

IDE 1

AMD

SB710

Chipset

ATX12 V1

8Mb

BIOS

CM OS

BA TT ERY

CLR CMOS 1

1

LAN

PHY

AUD IO

COD EC

Super

I/O

IR1

1

CD1

HD_A UDIO 1

1

PCIE1

FLOP PY1

HDLED RE SET

PLED PWRB TN

1

PANEL 1

SPEA KER1

1

SATAII _2(PO RT 1)

AMD

770

Chipset

PCI1

PCI2

980DE3/U3S3

SATAII _4(PO RT 3)

SATAII _3(PO RT 2)

Top:

LIN E I N

Cen ter :

FRO NT

Bot tom :

MIC IN

PS2

Mouse

PS2

Keyb oa rd

USB 2.0

T: USB0

B: USB1

Top:

RJ-45

USB 3.0

T: U SB 0

B: USB1

Front USB 3.0

ErP/EuP Ready

RoHS

USB 8_9

1

SATAII _1(PO RT 0)

SATAII _6(PO RT 5)

SATAII _5(PO RT 4)

1

PLED 1

1

HDMI _SPD IF1

USB 6_7

1

USB 4_5

1

USB 2.0

T: U SB 2

B: USB3

COM1

CHA _FAN1

Support 8-Core CPU

36

37

38

SOCKET AM3b

PCIE2

PCIE4

PCIE3

FSB8 00

DDR3 _A1 ( 6 4 bi t, 240-p in module)

DDR3 _A2 ( 6 4 bi t, 240-p in module)

FSB8 00

DDR3 _B1 ( 6 4 bi t, 240-p in module)

DDR3 _B2 ( 6 4 bi t, 240-p in module)

SATA3_ 2(POR T 7)

SATA3_ 1(POR T 6)

DDR3 1866

AM3+

140W CPU

CPU _FAN1PWR _FAN1

X

Fast RAM

X

Fast LAN

USB 3_2 _3

39

3

ASRock 980DE3/U3S3 R2.0 Motherboard

English

I/O Panel

LAN Port

ACT/LINK

LED

SPEED

LED

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No Link Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)

* 2 LAN RJ-45 Port 7 USB 3.0 Port (USB01)

3 Line In (Light Blue) 8 USB 2.0 Ports (USB23)

** 4 Front Speaker (Lime) 9 Serial Port: COM1

5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)

** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows

®

XP:

After restarting your computer, you will nd “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker

and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then

reboot your system.

For Windows

®

8.1 / 8 / 7 / Vista

TM

:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Conguration” to “Quadraphonic” or “Stereo”. Click “Device

advanced settings”, choose “Make front and rear output devices playbacks two different audio

streams simultaneously”, and click “ok”. Then reboot your system.

5

6

4

1

2

3

7

8

910

4

ASRock 980DE3/U3S3 R2.0 Motherboard

English

1. Introduction

Thank you for purchasing ASRock 980DE3/U3S3 R2.0 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It

delivers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found

in the user manual presented in the Support CD.

Because the motherboard specications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modications of this manual occur, the updated ver-

sion will be available on ASRock website without further notice. You may

nd the latest VGA cards and CPU support lists on ASRock website as

well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock 980DE3/U3S3 R2.0 Motherboard (ATX Form Factor)

ASRock 980DE3/U3S3 R2.0 Quick Installation Guide

ASRock 980DE3/U3S3 R2.0 Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

5

ASRock 980DE3/U3S3 R2.0 Motherboard

English

1.2 Specications

Platform - ATX Form Factor

- All Solid Capacitor design

- High Density Glass Fabric PCB

CPU - Support for Socket AM3+ Processors

- Support for Socket AM3 Processors: AMD Phenom

TM

II X6 /

X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /

Sempron Processors

- Supports 8-Core CPU

- Digi Power design

- Supports CPU up to 140W

- Supports AMD OverDrive™ with ACC feature (Advanced

Clock Calibration)

- Supports AMD’s Cool ‘n’ Quiet Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology

- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - Northbridge: AMD 770

- Southbridge: AMD SB710

Memory - Dual Channel DDR3 Memory Technology

- 4 x DDR3 DIMM Slots

- Supports DDR3 1866(OC)/1600(OC)/1333/1066/800

non-ECC, un-buffered memory (see CAUTION 1)

- Max. capacity of system memory: 32GB (see CAUTION 2)

Expansion Slot - 1 x PCI Express 2.0 x16 Slot (PCIE3 @ x16 mode)

- 3 x PCI Express 2.0 x1 Slots

- 2 x PCI Slots

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)

- Supports Surge Protection (ASRock Full Spike Protection)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports Lightning/ESD Protection (ASRock Full Spike

Protection)

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE

Rear Panel I/O - 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

6

ASRock 980DE3/U3S3 R2.0 Motherboard

- 4 x USB 2.0 Ports

- 2 x USB 3.0 Ports (Etron EJ188)

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

- HD Audio Jacks: Line in / Front Speaker / Microphone

Storage - 6 x SATA2 3.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 10 and JBOD), NCQ, AHCI and Hot Plug

- 2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061,

support NCQ, AHCI and Hot Plug

Connector - 1 x ATA133 IDE Connector (Supports 2 x IDE Devices)

- 1 x Floppy Connector

- 1 x IR Header

- 1 x HDMI_SPDIF Header

- 1 x Power LED Header

- 1 x CPU Fan Connector (4-pin)

- 1 x Chassis Fan Connector (4-pin)

- 1 x Power Fan Connector (4-pin)

- 1 x 24 pin ATX Power Connector

- 1 x 8 pin 12V Power Connector

- 1 x CD In Header

- 1 x Front Panel Audio Connector

- 3 x USB 2.0 Headers (Support 6 USB 2.0 ports)

- 1 x USB 3.0 Header (Etron EJ188) (Supports 2 USB 3.0

ports)

BIOS Feature - 8Mb AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliant wake up events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- CPU, VCCM, NB Voltage Multi-adjustment

Hardware - CPU temperature sensing

Monitor - Chassis temperature sensing

- CPU/Chassis/Power Fan Tachometer

- CPU Quiet Fan (Auto adjust chassis fan speed by CPU

temperature)

- CPU/Chassis/Power Fan multi-speed control

- Voltage monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

8.1 32-bit / 8.1 64-bit / 8 32-bit /

8 64-bit / 7 32-bit / 7 64-bit / Vista

TM

32-bit / Vista

TM

64-bit /

XP 32-bit / XP 64-bit

English

7

ASRock 980DE3/U3S3 R2.0 Motherboard

Certications - FCC, CE, WHQL

- ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

CAUTION!

1. Whether 1866/1600MHz memory speed is supported depends

on the AM3/AM3+ CPU you adopt. If you want to adopt DDR3

1866/1600 memory module on this motherboard, please refer

to the memory support list on our website for the compatible

memory modules.

ASRock website: http://www.asrock.com

2. Due to the operating system limitation, the actual memory size

may be less than 4GB for the reservation for system usage un-

der Windows

®

8.1 / 8 / 7 / Vista

TM

/ XP. For Windows

®

64-bit OS

with 64-bit CPU, there is no such limitation.

WARNING

Please realize that there is a certain risk involved with overclocking,

including adjusting the setting in the BIOS, applying Untied Overclocking

Technology, or using third-party overclocking tools. Overclocking may

affect your system’s stability, or even cause damage to the components

and devices of your system. It should be done at your own risk and

expense. We are not responsible for possible damage caused by

overclocking.

English

8

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2. Installation

This is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to

the motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static elec-

tricity, NEVER place your motherboard directly on the carpet or the

like. Also remember to use a grounded wrist strap or touch a safety

grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

anti-static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the mother-

board to the chassis, please do not over-tighten the screws! Doing

so may damage the motherboard.

9

ASRock 980DE3/U3S3 R2.0 Motherboard

English

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

Lever 90° Up

CPU Golden Triangle

Socker Corner

Small Triangle

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it ts in place.

The CPU ts only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it rmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat dis-

sipation. Make sure that the CPU and the heatsink are securely fastened

and in good contact with each other. Then connect the CPU fan to the

CPU FAN connector (CPU_FAN1, see Page 2, No. 3). For proper instal-

lation, please kindly refer to the instruction manuals of the CPU fan and

the heatsink.

10

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel conguration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR3 DIMM pair in the slots. In other words, you have to install identical DDR3

DIMM pair in Dual Channel (DDR3_A1 and DDR3_B1; Black slots; see p.2 No.6)

or identical DDR3 DIMM pair in Dual Channel (DDR3_A2 and DDR3_B2; Black

slots; see p.2 No.7), so that Dual Channel Memory Technology can be activated.

This motherboard also allows you to install four DDR3 DIMMs for dual channel

conguration, and please install identical DDR3 DIMMs in all four slots. You may

refer to the Dual Channel Memory Conguration Table below.

Dual Channel Memory Congurations

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

(Black Slot) (Black Slot) (Black Slot) (Black Slot)

(1) Populated - Populated -

(2) - Populated - Populated

(3)* Populated Populated Populated Populated

*

For the conguration (3), please install identical DDR3 DIMMs in all four

slots.

1. Please install the memory module into the slots DDR3_A2 and

DDR3_B2 for the rst priority.

2. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them either in the set of

slots DDR3_A1 and DDR3_B1, or in the set of slots DDR3_A2 and

DDR3_B2.

3. If only one memory module or three memory modules are installed

in the DDR3 DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

4. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel

Memory Technology .

5. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot; otherwise, this motherboard and DIMM may be dam-

aged.

6. If you adopt DDR3 1866/1600 memory modules on this mother-

board, it is recommended to install them on DDR3_A2 and DDR3_

B2 slots.

11

ASRock 980DE3/U3S3 R2.0 Motherboard

English

notch

break

notch

break

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only ts in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

12

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 4 PCI Express slots on this motherboard.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots:

PCIE1 / PCIE2 / PCIE4 (PCIE x1 slot; Black) is used for PCI Express

cards with x1 lane width cards, such as Gigabit LAN card and SATA2

card.

PCIE3 (PCIE x16 slot; Black) is used for PCI Express x16 lane width

graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press rmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

13

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2.5 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap

is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 38)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the

system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a

jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,

please do not clear the CMOS right after you update the BIOS. If you need

to clear the CMOS when you just nish updating the BIOS, you must boot

up the system rst, and then shut it down before you do the clear-CMOS ac-

tion. Please be noted that the password, date, time, user default prole, 1394

GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

14

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

Serial ATA3 Connectors These two Serial ATA3

(SATA3_1 (PORT 6): see p.2, No. 11)

(SATA3) connectors support

(SATA3_2 (PORT 7): see p.2, No. 9)

SATA data cables for internal

storage devices. The current

SATA3 interface allows up to

6.0 Gb/s data transfer rate.

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 27)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

the red-striped side to Pin1

Primary IDE connector (Black)

(39-pin IDE1, see p.2 No. 36)

Note: Please refer to the instruction of your IDE device vendor for the details.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

Serial ATA2 Connectors These six Serial ATA2 (SATA2)

(SATAII_1 (PORT 0): see p.2, No. 20)

connectors support SATA data

(SATAII_2 (PORT 1): see p.2, No. 19)

cables for internal storage

(SATAII_3 (PORT 2): see p.2, No. 18)

devices. The current SATA2

(SATAII_4 (PORT 3): see p.2, No. 17)

interface allows up to 3.0 Gb/s

(SATAII_5 (PORT 4): see p.2, No. 16)

data transfer rate.

(SATAII_6 (PORT 5): see p.2, No. 15)

SATAII_1 SATAII_3

(PORT 0) (PORT 2)

SATAII_2 SATAII_4

(PORT 1) (PORT 3)

SATAII_5

(PORT 4)

SATAII_6

(PORT 5)

SATA3_1

(PORT 6)

SATA3_2

(PORT 7)

15

ASRock 980DE3/U3S3 R2.0 Motherboard

English

1

USB_ PWR

P-8

GND

DUMMY

USB_ PWR

P+8

GND

P-9

P+9

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5)

ports on the I/O panel, there

(see p.2 No. 22)

are three USB 2.0 headers on

this motherboard. Each USB 2.0

header can support two USB

2.0 ports.

(9-pin USB6_7)

(see p.2 No. 21)

(9-pin USB8_9)

(see p.2 No. 23)

P- 7

P+ 7

GND

DUMMY

USB_PWR

P- 6

P+ 6

GND

1

Infrared Module Header This header supports an

(5-pin IR1)

optional wireless transmitting

(see p.2 No. 31)

and receiving infrared module.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

(Optional)

SATA / SATA2 / SATA3 hard

disk or the SATA3 connector on

this motherboard.

Internal Audio Connectors This connector allows you to

(4-pin CD1)

receive stereo audio input from

(CD1: see p.2 No. 28)

sound sources such as a

CD-ROM, DVD-ROM, TV tuner

card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1)

panel audio cable that allows

(see p.2 No. 29)

convenient connection and

control of audio devices.

J_SE NSE

OUT2 _L

1

MIC_ RET

PRES ENCE#

GND

OUT2 _R

MIC2 _R

MIC2 _L

OUT_RET

CD-L

GND

CD-R

CD1

16

ASRock 980DE3/U3S3 R2.0 Motherboard

English

1. High Denition Audio supports Jack Sensing, but the panel wire on

the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic.

For Windows

®

XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”.

For Windows

®

8.1 / 8.1 64-bit / 8 / 8 64-bit / 7 / 7 64-bit / Vista

TM

/

Vista

TM

64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

several system front panel

(see p.2 No. 24)

functions.

Connect the power switch, reset switch and system status indicator

on the chassis to this header according to the pin assignments below.

Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con-

gure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to per-

form a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The

LED is on when the system is operating. The LED keeps blinking

when the sys-tem is in S1 sleep state. The LED is off when the system

is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The

LED is on when the hard drive is reading or writing data.

GND

RES ET#

PWR BTN#

PLE D-

PLE D+

GND

HDL ED-

HDL ED+

1

GND

17

ASRock 980DE3/U3S3 R2.0 Motherboard

English

The front panel design may differ by chassis. A front panel module

mainly consists of power switch, reset switch, power LED, hard drive

activity LED, speaker and etc. When connecting your chassis front

panel module to this header, make sure the wire assignments and the

pin assign-ments are matched correctly.

Power LED Header Please connect the chassis

(3-pin PLED1)

power LED to this header to

(see p.2 No. 25)

indicate system power status.

The LED is on when the system

is operating. The LED keeps

blinking in S1 state. The LED is

off in S3/S4 state or S5 state

(power off).

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

speaker to this header.

(see p.2 No. 26)

1

+5V

DUMMY

SPEAKER

1

PLED+

PLED-

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

to the fan connectors and

(see p.2 No. 12)

match the black wire to the

ground pin.

(4-pin PWR_FAN1)

(see p.2 No. 2)

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

cable to the connector and

(see p.2 No. 3)

match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.

If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

GND

+12V

CPU_FAN_SPEED

FAN_SPEE D_CONTROL

1 2 3 4

GND

+12V

PWR_FAN_SPEED

FAN_SPEED_CONTROL

18

ASRock 980DE3/U3S3 R2.0 Motherboard

English

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

supply to this connector.

(see p.2 No. 10)

12

1

Though this motherboard provides 24-pin ATX power connector,

it can still work if you adopt a traditional 20-pin ATX power supply.

To use the 20-pin ATX power supply, please plug your power

supply along with Pin 1 and Pin 13.

ATX 12V Power Connector Please connect an ATX 12V

(8-pin ATX12V1)

power supply to this connector.

(see p.2 No. 1)

Though this motherboard provides 8-pin ATX 12V power connector, it can still work

if you adopt a traditional 4-pin ATX 12V power supply. To use the

4-pin ATX power supply, please plug your power supply along with

Pin 1 and Pin 5.

20-Pin ATX Power Supply Installation

4-Pin ATX 12V Power Supply Installation

12

1

24

13

24

13

5 1

8 4

5 1

8 4

HDMI_SPDIF Header HDMI_SPDIF header, providing

(2-pin HDMI_SPDIF1)

SPDIF audio output to HDMI

(

see p.2 No. 30)

VGA card, allows the system to

connect HDMI Digital TV/

projector/LCD devices. Please

connect the HDMI_SPDIF

connector of HDMI VGA card to

this header.

SPDIFOUT

GND

1

USB 3.0 Header Besides two default USB 3.0

(19-pin USB3_2_3)

ports on the I/O panel, there is

(see p.2 No. 39)

one USB 3.0 header on this

motherboard. This USB 3.0

header can support two USB 3.0

ports.

19

ASRock 980DE3/U3S3 R2.0 Motherboard

English

2.7 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to xed PCI / PCIE buses. Before you

enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS

setup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untied

during overclocking, but PCI / PCIE buses are in the xed mode so that FSB can

operate under a more stable overclocking environment.

Please refer to the warning on page 7 for the possible overclocking risk

before you apply Untied Overclocking Technology.

20

ASRock 980DE3/U3S3 R2.0 Motherboard

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)

to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you

wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>

+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS

Setup program is designed to be user-friendly. It is a menu-driven program, which

allows you to scroll through its various sub-menus and to select among the prede-

termined choices. For the detailed information about BIOS Setup, please refer to the

User Manual (PDF le) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 8.1 / 8.1

64-bit / 8 / 8 64-bit / 7 / 7 64-bit / Vista

TM

/ Vista

TM

64-bit / XP / XP 64-bit. The Support

CD that came with the motherboard contains necessary drivers and useful utilities

that will enhance motherboard features. To begin using the Support CD, insert the

CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTO-

RUN” is enabled in your computer. If the Main Menu does not appear automatically,

locate and double-click on the le “ASRSETUP.EXE” from the BIN folder in the Sup-

port CD to display the menus.

English

Sayfa yükleniyor ...

ASROCK 980DE3/U3S3 Kullanım kılavuzu

ASROCK 980DE3/U3S3 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler