Yamaha RX-V4/390 Kullanım kılavuzu
- Kategori
- Ses amplifikatörleri
- Tip
- Kullanım kılavuzu
Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
IMPORTANT!
Please record the serial number of this
unit in the space below.
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC
SHOCK
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
OWNER’S MANUAL
CONTENTS
Safety Instructions ................... 2
Features ................................... 4
Supplied Accessories .............. 4
Profile of This Unit .................... 5
Speaker Setup ......................... 6
Connections ............................. 7
Speaker Balance Adjustment
... 11
Basic Operations .................... 14
Tuning Operations .................. 17
Preset Tuning...........................18
Using Digital Sound Field
Processor (DSP) .................... 21
Setting the SLEEP Timer ....... 26
Remote Control Transmitter ... 27
Notes About the Remote Control
Transmitter...............................28
Troubleshooting ...................... 29
Specifications ......................... 30
Natural Sound Stereo Receiver
Thank you for selecting this YAMAHA stereo receiver.
RX-V490/390
2
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should
be moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that
produce heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the unit;
or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
19 Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
SAFETY INSTRUCTIONS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
3
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Caution: Read this before operating your unit
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical
shock, do not expose the unit to rain or water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If something drops into the set,
contact your dealer.
5 Do not use force on switches, controls or connection
wires. When moving the unit, first disconnect the power
plug and the wires connected to other equipment.
Never pull the wires themselves.
6 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
7 Always set the VOLUME control to “–
∞
” before starting
the audio source play. Increase the volume gradually to
an appropriate level after the play back has been
started.
8 To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical
storm.
9 Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding
that the unit is faulty.
10 AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than
the outlet is rated to provide.
FCC INFORMATION
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without
affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable
until it is too late, YAMAHA and the Electronic
Industries Association’s Consumer Electronics
Group recommend you to avoid prolonged
exposure from excessive volume levels.
We Want You Listening For A Lifetime
4
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
Remote Control Transmitter Batteries (size AA, R6, UM-3) Indoor FM Antenna
FEATURES
AM Loop Antenna
RX-V490 RX-V390
●
5 Speaker Configuration
Front: 70W + 70W (8Ω) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 70W (8Ω) RMS Output Power,
0.1% THD, 1 kHz
Rear: 15W + 15W (8Ω) RMS Output
Power, 0.7% THD, 1 kHz
Front: 60W + 60W (8Ω) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 60W (8Ω) RMS Output Power,
0.2% THD, 1 kHz
Rear: 15W (8Ω) RMS Output Power,
0.7% THD, 1 kHz
●
Digital Sound Field Processor
4 Programs for Digital Sound Field
Processing
2 Programs for Dolby Surround Decoding
(DOLBY PRO LOGIC and DOLBY PRO
LOGIC ENHANCED)
2 Programs for Digital Sound Field
Processing
2 Programs for Dolby Surround Decoding
(DOLBY PRO LOGIC and DOLBY 3
STEREO)
●
Automatic Input Balance Control for
Dolby Surround
●
Test Tone Generator for Easier Speaker
Balance Adjustment
●
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
●
40-Station Random Access Preset Tuning
●
Automatic Preset Tuning
●
Preset Station Shifting Capability (Preset
Editing)
●
IF Count Direct PLL Synthesizer Tuning
System
●
Video Signal Input/Output Capability
●
SLEEP Timer
●
Remote Control Capability
RX-V390
RX-V390
RX-V490
RX-V490
5
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver – an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a totally new listening environment. In addition, you get incredible realism from
Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of actual music venues to allow you to accurately
recreate live performance environments in your own home.
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of a Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic gets its name from its professional-grade steering logic
circuitry, which provides greater effective front and rear
channel separation for a much higher degree of realism than
the “passive” Dolby Surround circuits found in less
sophisticated home audio/video equipment. Dolby Pro Logic
Surround provides a true center channel, so there are four
independent channels, unlike passive Dolby Surround which
has in effect only three channels: left, right, and rear. This
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from action on the
screen while getting a stereo effect as well.
In addition, this unit features a built-in automatic input balance
control. This circuit always presents you the best surround
conditions without performing manual adjustments.
Dolby Pro Logic Surround + DSP
You can also enjoy a combination of Dolby Pro Logic Surround
and DSP in the sound field program “ PRO LOGIC
ENHANCED”.
It recreates the surround effect of a movie theater, effectively
duplicating its multiple surround loudspeaker system,
completely surrounding the listener with the sounds of the
action taking place on the screen.
RX-V490 only
6
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are front speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within the Dolby Surround encoded programs. The center speaker needs to be equal in power to the front
speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If a Dolby Surround program is selected,
conversations will be output from the center speaker and the
ambience will be excellent.
●
Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 12.)
4-Speaker Configuration
The center speaker is not used in this configuration. If a Dolby
Surround program is selected, the center sound is output from
the left and the right front speakers. However, the sound effect
of other programs can be the same as that of the 5-speaker
configuration.
●
Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 12.)
●
The program DOLBY 3 STEREO is useless in this
configuration.
*
As this unit is equipped with a monaural amplifier for the rear channel, you may use one rear speaker only instead of using two
rear speakers.
However, the use of two rear speakers is recommended when there are more than one listener in the listening room.
When using one rear speaker, place it right behind your listening position.
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the front speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
RX-V390 only
RX-V390 only
7
CONNECTIONS
●
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
●
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
:Refer to “ABOUT THE ACCESSORY TERMINALS” on page 9.
MONITOR
OUT
LD/TV
IN
OUT
VCR
PHONO CD
TAPE
LD/TV
VCR
TAPE
PB
REC
OUT
IN OUT
A OR B:6
Ω
MIN./SPEAKER
A B:l2
Ω
MIN./SPEAKER
120V 60Hz
100W MAX. TOTAL
VIDEO
SIGNAL
AUDIO SIGNAL
SPEAKERS
FRONT
AC OUTLETS
SWITCHED
A
B
A
B
FM
ANT
AM
ANT
GND
75Ω
UNBAL
OUTPUT
VIDEO IN
AUDIO OUT
VIDEO OUT
OUTPUT
LINE OUT
LINE IN
VIDEO OUT
AUDIO OUT
AUDIO IN
VIDEO IN
GND
GND
(U.S.A. model)
To AC outlet
Front speakers A
Front speakers B
Right
Right Left
Left
Video cassette recorderTape deckCD player
LD player,
TV tuner, etc.
Monitor TVTurntable
Note on front speaker connection:
One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the
SPEAKERS A or B terminals..
8
Center and rear speakers
Connect the respective speakers to this unit as figured below.
Only one rear speaker can also be used in place of two rear
speakers.
For connecting one rear speaker, follow the method shown
below.
CENTER
REAR
REAR
R
L
R
L
CENTER
REAR
REAR
CENTER
REAR SINGLE
REAR
REAR
RX-V390
RX-V490
Rear speakers
Center speaker
Rear speakers
Center speaker
Rear speaker
9
For connecting speakers
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
Note
Use speakers with the specified impedance shown on the rear
of this unit.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Press and open the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Press the tab back to
the original position and
secure the wire.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀
Press the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Release the tab and
secure the wire.
➀
➁
➂
➁
➂
➀
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
(U.S.A., Canada and General models)
.......................................................... 2 SWITCHED OUTLETS
(Australia model) ................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
Use one of the two GND terminals on the rear of this unit for
the connection.
RX-V390 only
FM
ANT
AM
ANT
GND
75Ω
UNBAL
GND
or
Turntable
Loosen Tighten
10
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
FM
ANT
AM
ANT
GND
75Ω
UNBAL.
Outdoor FM antenna
Indoor FM
antenna
(included)
75-ohm/300-ohm
antenna adapter
75-ohm
coaxial cable
300-ohm
feeder
Outdoor AM antenna
AM loop
antenna
(included)
Ground
➀
➁
➂
Orient so that the best
reception is obtained.
12 3
11
1
Set to the “
∞
” position.
2 Select the front speakers to be used.
* If you use two front speaker systems, press both the A
and B switches.
3
Set to the “0” position.
4 Turn the power on.
5 Turn the DSP on, so that a program name appears on
the display.
6 Select PRO LOGIC, so that the corresponding
name is illuminated on the display.
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test
tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker.
This is important for the best performance of the digital sound field processor.
SPEAKERS
A
B
ON
OFF
ON
OFF
BASS
55
4
3
2
l
0
l
2
3
4
TREBLE
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
POWER
DECK
A
/
B
VCR MON
REC/PAUSE
STOP
ENHANCED
—
+
+
—
CENTER
MODE
PRO LOGIC
MONO MOVIE ROCK
DELAY
TIME
EFFECT
ON/OFF
VOLUME
SUR.
CNCT VIDEO
HALL
6
DECK
A
/
B
VCR MON
REC/PAUSE
STOP
3 STEREO
—
+
+
—
CENTER
MODE
PRO LOGIC
HALL ROCK
DELAY
TIME
EFFECT
ON/OFF
VOLUME
SUR.
6
CONTINUED
6
1
4
2
3
5
EFFECT
PROGRAM
T
PRO LOGIC
RX-V490 RX-V390
12
7 Select the center channel output mode according to your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
On the feature of each mode, refer to the “Note” shown
below.
8
9 Turn up the volume.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two
seconds each. The display changes as shown below.
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
Note
In step 7, when you select the center channel output mode,
note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the front speakers. In this
mode, the bass tone will be output from the front
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the front speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right front speakers.
*
When the DOLBY 3 STEREO program is used, the
PHANTOM mode cannot be selected.
Flashes continuously.
CENTER
MODE
TEST
TEST
NORMAL
WIDE
PHANTOM
Front (L) Center
Rear
(L and R)
Front (R)
DECK
A
/
B
VCR MON
REC/PAUSE
STOP
ENHANCED
—
+
+
—
CENTER
MODE
PRO LOGIC
MONO MOVIE ROCK
DELAY
TIME
EFFECT
ON/OFF
VOLUME
SUR.
CNCT VIDEO
HALL
9
7
DECK
A
/
B
VCR MON
REC/PAUSE
STOP
3 STEREO
—
+
+
—
CENTER
MODE
PRO LOGIC
HALL ROCK
DELAY
TIME
EFFECT
ON/OFF
VOLUME
SUR.
9
7
9
8
RX-V490
RX-V390
RX-V390
RX-V490
RX-V390 only
(L and R)
13
10 Adjust the BALANCE control so that the effect sound
output level of the left front speaker and the right front
speaker are the same.
11 Adjust the sound output level of the center speaker to
be at the same level as that of the front speakers with
the CENTER LEVEL control.
12 Adjust the sound output level of the rear speakers to
be at the same level as that of the front speakers with
the REAR LEVEL control.
13 Cancel the test tone.
Notes
●
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the VOLUME keys on the remote
control transmitter).
●
If you use external power amplifiers, their volume controls
may also be adjusted to achieve proper balance.
●
In step 11, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this mode,
the center sound is automatically output from the left and
right front speakers.
10
11
12
13
CENTER
LEVEL
0l0
REAR
LEVEL
0l0
TEST
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
“TEST” stops flashing
and disappears.
14
1
Set to the “
∞
” position.
2 Turn the power on.
3 Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
* The name of the selected input source will appear in
the display.
4 Select the front speakers to be used.
* If you use two front speaker systems, press both the A and
B switches.
5 Play the source. (For detailed information on the
tuning operation, refer to page 17.)
6
Adjust to the desired output level.
7 If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to page 16) and use the digital
sound field processor. (Refer to page 23.)
Notes on using the input selector buttons
●
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
●
The selection of TAPE MONITOR or VCR MONITOR
cannot be canceled by pressing another input selector
button. To cancel it, press it again.
●
In step 3, if two or more program sources are selected at
the same time, be sure to remember the priority order of
the input sources.
Priority order of sources: 1) TAPE MONITOR, 2) VCR
MONITOR, 3) LD/TV, TUNER, CD or PHONO.
* If you select LD/TV, TUNER, CD or PHONO, be sure
that neither TAPE MONITOR nor VCR MONITOR have
been selected.
* If you select TAPE MONITOR and VCR MONITOR and
another input selector button at the same time, the
playback result will be the video image from the VCR
and the sound from the audio tape.
* If you select both LD/TV and TAPE MONITOR at the
same time, the playback result will be the video image
from the LD player and the sound from the audio tape.
* Once you play the LD player, its video image will not be
interrupted even if other input selector buttons except
VCR MONITOR are selected.
To turn off the power
Press the POWER switch again.
BASIC OPERATIONS
TO PLAY A SOURCE
SPEAKERS
A
B
ON
OFF
ON
OFF
VCR
MONITOR
LD/TV
TAPE
MONITOR
TUNER CD PHONO
COPY
3
1, 6
2
4
7
7
POWER
15
1 Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown at
right.
* When you select LD/TV, TUNER, CD or PHONO, make
sure that neither TAPE MONITOR nor VCR MONITOR is
also selected.
2
Play the source and then turn the VOLUME control
up to confirm the input source. (For detailed information
on the tuning operations, refer to the page 17.)
3 Set the tape deck or VCR to the recording mode.
4 To monitor the audio and/or video signals being
recorded, press the input selector button for the tape
deck or VCR used to make the recording.
Notes
●
To dub from tape to tape, only the following method of
dubbing can be performed.
●
The DSP, VOLUME, BASS, TREBLE and BALANCE
control settings have no effect on the material being
recorded.
TO RECORD A SOURCE TO TAPE (OR DUB FROM TAPE TO TAPE)
SOURCE
VCR (or tape deck)
connected to the VCR
terminals.
RECORDER
Tape deck connected to
the TAPE terminals.
→
2
1, 4
VCR
MONITOR
LD/TV
TAPE
MONITOR
TUNER CD PHONO
COPY
VCR
MONITOR
LD/TV
TAPE
MONITOR
TUNER CD PHONO
COPY
16
Because one or two speaker systems (as front speakers) can
be connected to this unit, the SPEAKERS switches allow you
to select speaker system A or B, or both at once.
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
Note
This control is effective only for the sound from the front
speakers.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Note
These controls are effective only for the sound from the front
speakers.
When you listen with headphones
Connect the headphones to the PHONES jack. You can listen
to the sound to be output from the front speakers through
headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
switch.
Selecting the SPEAKER system
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control
PHONES
SPEAKERS
A
B
ON
OFF
ON
OFF
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
TREBLE
55
4
3
2
l
0
l
2
3
4
BASS
55
4
3
2
l
0
l
2
3
4
17
1 Select the reception band (FM or AM) while watching
the display.
2
3 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
FM/AM
FM AM
or
1 Select the reception band (FM or AM) while watching
the display.
2
3
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stops is not the desired
one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
Display information
➀
Displays the band and frequency of the received station.
➁
Lights up when an FM stereo broadcast is received in
stereo.
➂
Indicates the signal level of the received station.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
AUTOMATIC TUNING MANUAL TUNING
FM/AM
TUNING
MODE
AUTO/MAN’L MONO
TUNING
MODE
AUTO/MAN’L MONO
DOWN
TUNING UP
DOWN
TUNING UP
AUTO TUNING
“AUTO TUNING”
goes off.
FM AM
or
1 3
2
RX-V490
RX-V390
PRESET
MHz
FM
STEREO
0
20
l00
REAR
➀
➁
➂
➀➁
➂
PRESET
MHz
FM
STEREO
0
20
l00
40 60
DELAY
CONCERT
VIDEO
MONO
MOVIE
C
18
1 Tune to a desired station.
(Refer to the previous page for tuning procedure.)
2 Select a desired page (A – E) of preset station buttons
while watching the display.
3
4 Press a preset station button before “MEMORY”
goes off from the display.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations to the preset station
buttons on other pages in the same way by selecting
other pages in step 2.
11 Select the page of preset station buttons.
22 Select the desired preset station button.
Notes
●
A new setting can be programmed in place of the former
one.
●
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If
so, it can be re-programmed by simply following the PRESET
TUNING steps.
MANUAL PRESET TUNING
This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this function, you can
select any desired station by only pressing the corresponding preset station button. Up to 40 stations (8 stations x 5 pages) can be
stored.
PRESET TUNING
To store stations
To recall a preset station
3
2, 11
4, 22 (Preset station buttons)
A/B/C/D/E
PRESET
MEMORY
MAN’L/AUTO FM
MEMORY
A/B/C/D/E
PRESET
Flashes on and off
for about 5 seconds.
l 2345 67 8
PRESET STATIONS
l 2345 67 8
PRESET STATIONS
Shows the displayed station has been
programmed to A1.
PRESET
RX-V490
RX-V390
PRESET
MHz
FM
AUTO TUNING
STEREO
0
20
l00
40 60
DELA
CON
VI
PRESET
MHz
FM
STEREO
0
20
l00
AUTO TUNING
19
1
2
3
To tune to higher frequencies, press right side once.
To tune to lower frequencies, press left side once.
* If the TUNING button is not pressed, in a while, the
automatic preset tuning begins automatically toward higher
frequencies.
The automatic preset tuning begins from the frequency
currently displayed. Received stations are programmed to
A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the first received station to
C5, select “C5” by using the A/B/C/D/E button and the preset
station buttons after pressing the MEMORY button in step 2.
Then press the TUNING button. The first received station is
stored to C5, and next stations to C6, C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 18.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 18.
Notes
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 18.
●
If the number of received stations is not enough to be stored
up o E8, the search is finished automatically after searching
through all frequencies.
●
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 18.
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 18.
To store stations
Press and hold for
about 3 seconds.
FM/AM
FM
MEMORY
MAN’L/AUTO FM
2
1 3
Flashes.
DOWN
TUNING UP
MEMORY
AUTO TUNING
20
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations with each other as shown below.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 18).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Flashes
Flashes
EDIT
EDIT
MEMORY
MEMORY
2, 4
RX-V490
RX-V390
Shows the exchange of stations is completed.
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
Yamaha RX-V4/390 Kullanım kılavuzu
- Kategori
- Ses amplifikatörleri
- Tip
- Kullanım kılavuzu
- Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
diğer dillerde
- español: Yamaha RX-V4/390 Manual de usuario
- français: Yamaha RX-V4/390 Manuel utilisateur
- italiano: Yamaha RX-V4/390 Manuale utente
- svenska: Yamaha RX-V4/390 Användarmanual
- čeština: Yamaha RX-V4/390 Uživatelský manuál
- polski: Yamaha RX-V4/390 Instrukcja obsługi
- Deutsch: Yamaha RX-V4/390 Benutzerhandbuch
- português: Yamaha RX-V4/390 Manual do usuário
- English: Yamaha RX-V4/390 User manual
- dansk: Yamaha RX-V4/390 Brugermanual
- русский: Yamaha RX-V4/390 Руководство пользователя
- suomi: Yamaha RX-V4/390 Ohjekirja
- Nederlands: Yamaha RX-V4/390 Handleiding
- română: Yamaha RX-V4/390 Manual de utilizare