MY16-ES64 Owner’s Manual
1
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
MANUALE DI ISTRUZIONI
OWNER’S MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
MANUALE DI ISTRUZIONI
JA
ZH
IT
ES
FR
DE
EN
ITALIANO ESPAÑOL FRANÇAIS DEUTSCH ENGLISH
EtherSound
®
INTERFACE CARD
EtherSound
®
INTERFACE CARD
MY16-ES64
MY16-ES64
2
MY16-ES64 Owner’s Manual
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT:
When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : EtherSound INTERFACE CARD
Model Name : MY16-ES64
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference
that may cause undesired operation.
See user manual instructions if interference to radio reception is sus-
pected.
(FCC DoC)
CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
• This applies only to products distributed by Yamaha Canada Music Ltd. (class B)
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
(class b korea)
ENGLISH
MY16-ES64 Owner’s Manual
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injur y or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not
limited to, the following:
• Before installing the card in an audio device please check to make sure that the device is compatible with the card and check possible restrictions
regarding the maximum number of Yamaha and third-party expansion cards that can be simultaneously installed. Refer to the owner’s manual supplied
with the audio device, and/or the Yamaha Pro Audio web site at:
http://www.yamahaproaudio.com/
• Do not install the card in any Yamaha products not specified by Yamaha for use with the card to avoid possible electrical shock, fire, or equipment
damage.
• Do not attempt to disassemble or modify the card. Do not apply excessive force to card connectors or other card components. Mishandling of the card
may lead to shock, fire hazard, or equipment failure.
• Be sure to disconnect the power cable of the host device before installing the card and connecting/disconnecting the cables (in order to eliminate shock
hazard, undesired noise, and avoid equipment damage).
•Turn off all peripheral devices connected to the host device before installation, and unplug all related cables.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injur y to you or others, or
damage to the device or other property. These precautions include, but are not limited to, the following:
• Be sure to properly ground the host device to prevent electrical shock and/or malfunction.
• Do not touch the metallic leads (pins) of the circuit board when handling the card. The pins are sharp and may cause hand cuts.
•Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands on sharp edges.
•Avoid touching exposed connectors and metal parts to minimize the possibility of bad connections.
• Drain all static electricity from your clothing and body before handling the card. Static electricity can damage the card. Touch an exposed metal part of the
host device or other grounded object beforehand.
• Do not drop the card or subject it to physical shock as this can result in breakage and/or malfunction.
• Do not drop screws or other small parts inside the card. If power is applied while screws or similar metal objects are loose inside the unit the card may
malfunction or be damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualified Yamaha service personnel.
• The illustrations as shown in this Owner’s Manual are for instructional purposes only, and may be different from the ones on your equipment.
• Ethernet is a trademark of Xerox Corporation.
• EtherSound is a registered trademark of Digigram S.A.
• The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.
To customers using an MY16-EX card
Be sure to turn off host devices BEFORE plugging or unplugging the Ethernet cables that connect to a master card such as the MY16-ES64 or other
MY16-EX cards.
Plugging or unplugging the cables while power to the devices is on may result in serious noise.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or
destroyed.
ENGLISH
Introduction
4
MY16-ES64 Owner’s Manual
Thank you for purchasing the Yamaha MY16-ES64 EtherSound® interface card. MY16-ES64 is an EtherSound®
card for use with compatible Yamaha professional audio equipment.
Using the MY16-ES64 with a maximum of three MY16-EX Yamaha I/O expansion cards allows transmission and
reception of up to 64 channels (in/out) of uncompressed digital audio signals when running at a sampling
frequency of 48 kHz or 44.1 kHz.
About the host devices in which the MY16-ES64
can be installed
Before installing the card in a host device, please refer to the
Yamaha Pro Audio web site for the latest information on the
compatible host devices in which the card can be installed.
Yamaha Pro Audio web site:
http://www.yamahaproaudio.com/
EtherSound Firmware Update
The EtherSound firmware can be updated from a computer
connected to the EtherSound connector.
Information about the latest versions and firmware downloads
are available at the AuviTran website:
http://www.auvitran.com/
Installation information
Please refer to the owner’s manual supplied with the host
device for installation information.
As well as securing the card in place, the fixing screws at the left
and right of the card function as electrical grounds. Be sure to
screw them in tightly.
Accessories
Owner's Manual
■
Panel
A
EtherSound [IN][OUT] Connectors
These are RJ-45 connectors that you can connect to other
EtherSound devices or to a computer using an Ethernet
cable. Use “AVS-ESMonitor,” AuviTran’s application
software, to make settings for control and/or digital audio
signal transmission and reception.
NOTE:
• Use RJ-45 connectors that are compatible with
Neutrik’s etherCON CAT5
®
.
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Also, firmly fasten the
metal portion of the connector to the shield of the cable
using conductive tape, etc.
•For more details on EtherSound specifications and the
length of available cables, refer to the following website.
http://www.ethersound.com/
B
IN/OUT[TX][RX] Indicators
Each corresponding indicator blinks when EtherSound
[IN]/[OUT] connectors transmit or receive signals. When
the [Identify] button for the MY16-ES64 is selected from
the AVS-ESMonitor, all four of these indicators blink and
will continue blinking until selected a second time.
Introduction
Part Names and Functions
1
2 4
3
About AVS-ESMonitor
AV S-ESMonitor is application software made by the
AuviTran SARL for the purpose of monitoring and
controlling an EtherSound system. It allows you to make
various EtherSound settings such as input/output routing.
For details, refer to the following web site.
http://www.auvitran.com/
ENGLISH
Part Names and Functions
MY16-ES64 Owner’s Manual
5
C
[HA REMOTE] Connector
This is a D-sub 9-pin connector that enables remote
control of a Yamaha AD8HR or AD824 AD converter via
EtherSound. In most situations, you will connect to the
[REMOTE] connector of the host device using a serial
cross cable. If you use a host device, such as Yamaha digital
mixer LS9, which is capable of remotely controlling
directly via a slot connection, you do not need to connect
this [HA REMOTE] connector to the host device.
D
[NEXT MY16-EX IN][NEXT MY16-EXOUT]
Connectors
These RJ-45 connectors can be connected via an Ethernet
cable (CAT5e or higher category) to the [MASTER SIDE
IN] or [MASTER SIDE OUT] connector of the Yamaha
MY16-EX I/O expansion card for transmission and
reception of the audio and word clock signals.
NOTE:
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Using a UTP (Unshielded
Twisted Pair) cable may cause noise or cut off sound.
Also, be sure to attach the ferrite core included with the
MY16-EX to a location close to the cable plug
connected to the [NEXT MY16-EX OUT] connector.
• Do not use cables that feature protective boots for their
plugs as they could come in contact with the cable
connected to the [HA REMOTE] connector.
■
Switches
Set these switches as appropriate for your situation and for the device in which the card is installed.
A
Signals via [HA REMOTE] Connector
(SW1)
Typically set this switch to the [422] position. When you
connect the [HA REMOTE] connector to a computer, set
this switch to the [232] position.
B
Sampling Frequency (SW2)
NOTE:
This card supports only Double Speed mode when
running at 88.2/96kHz. (Double Channel mode is not
supported.)
C
Card ID (SW3)
Typically set this switch to the [Emu.] position. If you set
this switch to the [Emu.] position and switch
2
(SW2) to
the [48K] position, the host device will recognize the card
as a Yamaha MY16-AT digital I/O card. If you set this
switch to the [Emu.] position and switch
2
(SW2) to the
[96K] position, the host device will recognize the card as a
Yamaha MY8-AE96 digital I/O card. If you install the card
in a host device whose firmware supports the MY16-ES64,
setting this switch to the [Nat.] position enables you to
make best use of the MY16-ES64 function.
D
Operation Mode (SW4)
Typically set this switch to the [OnChip] position. You will
set this switch to the [BOOT] position to update the
firmware in the future.
E
SW201
Leave this switch permanently set to the [OFF] position
during use. Please do not change this setting. Otherwise
the card will not operate properly.
Word Clock Master Settings on the host
devices
The word clock master settings will differ as per the following
chart, depending on whether the MY16-ES64 card(s) (that are
not a primary master) have been installed in the same device as
the primary master MY16-ES64 card.
* SLOT:
Indicates the slot in which the MY16-ES64 is installed.
SW3
SW1
SW4
232 422
Emu.SW248K
96K
OnChip
BOOT
Nat.
1234
5
SW201
OFF
Mode Position
RS-232C 232
RS-422 422
Mode Position
44.1/48 kHz 48K
88.2/96 kHz 96K
Mode Position
Emulation Emu.
Native Nat.
Primary Master
Other than Primary
Master
If installed in
different
devices
Select other than
“SLOT”
Select “SLOT”
If installed in
the same
device
Select other than “SLOT”
ITALIANOESPAÑOLFRANÇAISDEUTSCHENGLISH
Connection Example
26
MY16-ES64 Owner’s Manual
Î
Connection Example
MY16-ES64
(1–16 ch)
Ethernet Straight Cable
Ethernet Cable
MY16-EX #1
(17–32 ch)
MY16-EX #2
(33–48 ch)
MY16-EX #3
(49–64 ch)
EtherSound Device
(Yamaha DME Satellite series,
NAI48-ES etc.)
Computer or
EtherSound Device
Ethernet Straight Cable
Ethernet Straight Cable
ITALIANO ESPAÑOL FRANÇAIS DEUTSCH ENGLISH
Appendix
MY16-ES64 Owner’s Manual
27
Connector Pin Assignment
HA REMOTE
Dimensions
*Specifications and descriptions in this owner’s manual
are for information purposes only. Yamaha Corp.
reserves the right to change or modify products or
specifications at any time without prior notice. Since
specifications, equipment or options may not be the
same in every locale, please check with your Yamaha
dealer.
*Die technischen Daten und Beschreibungen in dieser
Bedienungsanleitung dienen nur der Information.
Yamaha Corp. behält sich das Recht vor, Produkte oder
deren technische Daten jederzeit ohne vorherige
Ankündigung zu verändern oder zu modifizieren. Da
die technischen Daten, das Gerät selbst oder
Sonderzubehör nicht in jedem Land gleich sind, setzen
Sie sich im Zweifel bitte mit Ihrem Yamaha-Händler in
Ve r b indung.
*
Les caractéristiques techniques et les descriptions du
mode d
’
emploi ne sont données que pour information.
Yamaha Corp. se réserve le droit de changer ou
modifier les produits et leurs caractéristiques
techniques à tout moment sans aucun avis. Du fait que
les caractéristiques techniques, les équipements et les
options peuvent différer d
’
un pays à l
’
autre, adressez-
vous au distributeur Yamaha le plus proche.
* Las especificaciones y descripciones de este manual del
propietario tienen sólo el propósito de servir como
información. Yamaha Corp. se reserva el derecho a
efectuar cambios o modificaciones en los productos o
especificaciones en cualquier momento sin previo aviso.
Puesto que las especificaciones, equipos u opciones
pueden no ser las mismas en todos los mercados, solicite
información a su distribuidor Yamaha.
*Le specifiche e le descrizioni presenti in questo
manuale sono fornite a fini puramente informativi.
Yamaha Corp. si riserva il diritto di modificare
prodotti o specifiche in qualsiasi momento senza
preavviso. Dato che le specifiche, le apparecchiature o
le opzioni possono essere diverse da paese a paese,
verificarle con il proprio rappresentante Yamaha.
European models
Purchaser/User Information specified in EN55103-1 and
EN55103-2.
Conforms to Environments: E1, E2, E3 and E4
Europäische Modelle
Käufer/Benutzerinformationen nach EN55103-1 und
EN55103-2.
Entspricht den Umgebungen: E1, E2, E3 und E4
Pour les modèles distribués en Europe
Les informations d’achat/utilisation sont décrites dans
les documents EN55103-1 et EN55103-2.
Conformité aux normes environnementales : E1, E2, E3
et E4
Modelos europeos
Información comprador/usuario especificada en
EN55103-1 y EN55103-2.
Conforme para entornos: E1, E2, E3 y E4
Modelli europei
Informazioni acquirente/utente specificate in EN55103-1
e EN55103-2.
Conforme agli ambienti: E1, E2, E3 e E4
Appendix
Pin No.
Signal Name Pin No. Signal Name
1 N.C. 6 RX+
2 RX– 7 RTS
3 TX– 8 CTS
4 TX+ 9 N.C
5 GND
120
40
164.1
12
176.1
Unit: mm
310IPDHx.x-xxC0
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
Yamaha Pro Audio global web site:
http://www.yamahaproaudio.com/
© 2007-2013 Yamaha Corporation
C.S.G., PA Development Division
Printed in Japan
WK60020
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
HEAD OFFICE
Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
FRANCE
Ya mah a M u s i c E u r ope
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Ya mah a M u s i c G u l f F Z E
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Ya mah a M u s i c G u l f F Z E
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yam a ha C or p or a ti o n
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yam a ha M us i c A u st r al i a P t y. Lt d .
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yam a ha C or p or a ti o n
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
PA36
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Yamaha EtherSound MY16-ES64 El kitabı
- Tip
- El kitabı
diğer dillerde
- español: Yamaha EtherSound MY16-ES64 El manual del propietario
- français: Yamaha EtherSound MY16-ES64 Le manuel du propriétaire
- italiano: Yamaha EtherSound MY16-ES64 Manuale del proprietario
- svenska: Yamaha EtherSound MY16-ES64 Bruksanvisning
- čeština: Yamaha EtherSound MY16-ES64 Návod k obsluze
- polski: Yamaha EtherSound MY16-ES64 Instrukcja obsługi
- Deutsch: Yamaha EtherSound MY16-ES64 Bedienungsanleitung
- português: Yamaha EtherSound MY16-ES64 Manual do proprietário
- English: Yamaha EtherSound MY16-ES64 Owner's manual
- dansk: Yamaha EtherSound MY16-ES64 Brugervejledning
- suomi: Yamaha EtherSound MY16-ES64 Omistajan opas
- Nederlands: Yamaha EtherSound MY16-ES64 de handleiding
- română: Yamaha EtherSound MY16-ES64 Manualul proprietarului