Magmaweld MONOCUT 45i Plasma Cutting Mechanized El kitabı

monoCUT 45ix

monoCUT 45i

(+90) 444 93 53

magmaweld.com

info@magmaweld.com (+90) 538 927 12 62

USER MANUAL



Magma Mekatronik may modify the information and the images without any prior notice.







3monoCUT 45ix / monoCUT 45i

INVERTER PLASMA CUTTING MACHINE EN

PLASMASCHNEIDER MIT INVERTERTECHNOLOGIE DE

MACHINE DE DÉCOUPE PLASMA À ONDULEUR FR

 RU

MÁQUINA DE CORTE POR PLASMA TIPO INVERTER

MÁQUINA DE CORTE POR PLASMA INVERSOR

PT

ES

INVERTER PLASMASNIJMACHINE

 TR

    AR

NL

EN

4

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45i

1

1.1

1.2

1.3

1.4

1.5

2

2.1

2.2

2.3

2.4

2.5

2.5.1

2.5.2

2.5.3

2.6

2.7

2.8

2.8.1

3

3.1

3.2

4

4.1

4.2

4.3

5

5.1

5.2

5.3

5.4

5.5

SAFETY PRECAUTIONS

TECHNICAL INFORMATION

General Information

Machine Components

Product Label

Technical Data

Accessories

INSTALLATION

Delivery Control

Installation and Operation Recommendations

Mains Plug Connection

Connection to Mains

Connections for Plasma Cutting

Gas Connections

Grounding Pliers Connections

Torch Connections

Placing Consumables

Pilot Arc

Remote Control

Communication

OPERATION

User Interface

Torch Usage

MAINTENANCE AND SERVICE

Maintenance

Troubleshooting

Error Codes

ANNEX

Plasma Cutting Automation Connection Diagram

Manual Torch Consumables and Spare Parts

Mechanized Torch Consumables and Spare Parts

Plasma Cutting Machine Spare Parts List

Connection Diagrams

5

11

13

14

15

16

17

18

19

20

24

25

26

28

30

31

32

33

35

CONTENTS

Contents

EN

5

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i Safety Precautions

Be Sure To Follow All Safety Rules In This Manual!

• Safety symbols found in the manual are used to identify potential hazards.

• When any one of the safety symbols are seen in this manual, it must be understood that there is

a risk of injury and the following instructions should be read carefully to avoid potential hazards.

• The possessor of the machine is responsible for preventing unauthorized persons from

accessing the equipment.

• Persons using the machine must be experienced or fully trained in welding / cutting they have to

read the user manual before operation and follow the safety instructions.

Explanation Of Safety

Information

• Read the user manual, the label on the machine and the safety instructions carefully.

• Make sure that the warning labels on the machine are in good condition. Replace missing and

damaged labels.

• Learn how to operate the machine, how to make the checks in a correct manner.

• Use your machine in suitable working environments.

• Improper changes made in your machine will negatively affect the safe operation and its

longevity.

• The manufacturer is not responsible for the consequences resulting from the operation of the

 

Comprehending Safety

Precautions

Explanation Of Safety

Symbols

ATTENTION

Indicates a potentially hazardous situation that could cause injury or damage.

In case if no precaution is taken, it may cause injuries or material losses / damages.

IMPORTANT



DANGER

Indicates a serious danger. In case if not avoided, severe or fatal injuries may occur.

Make certain that the installation procedures comply with national electrical standards



persons.

• Wear dry and sturdy insulated gloves and working apron. Never use wet or damaged gloves and

working aprons.

 

operator must be protective against sparks, splashing and arc radiation.

• Do not work alone. In case of a danger make sure you have someone for help in your working

environment.

• Do not touch the electrode with the bare hand. Do not allow the electrode holder or electrode to

come in contact with any other person or any grounded object.

• Never touch parts that carry electricity.

• Never touch the electrode if you are in contact with the electrode attached to the work surface,

 



 

material that is large enough to cut off the operator’s contact with the work surface.

• Do not connect more than one electrode to the electrode holder.



as practical.

• Check the torch before operating the machine. Make sure the torch and its cables are in good

condition. Always replace a damaged, worn torch.

• Do not touch electrode holders connected to two machines at the same time since double

 

• Keep the machine turned off and disconnect cables when not in use.

• Before repairing the machine, remove all power connections and / or connector plugs or turn

off the machine.

• Be careful when using a long mains cable.

Electric Shocks

May Kill

SAFETY PRECAUTIONS

EN

6

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45iSafety Precautions

• Turn off the electric power.



or wires.

• Call for emergency services.



• If the victim is not breathing, Administer cardiopulmonary resuscitation (CPR) immediately

after breaking contact with the electrical source. Continue CPR (cardiac massage) until

breathing starts or until help arrives.



• Treat an electrical burn as a thermal burn by applying sterile, cold (iced) compresses. Prevent

contamination, and cover with a clean, dry dressing.

Procedures for

Electric Shock

Long-term inhalation of fumes and gases released from welding / cutting is very dangerous.

• Keep away from the moving parts.



closed and in locked position.

• Wear metal toe shoes against the possibility of heavy objects falling on to your feet.

• Burning sensations and irritations in the eyes, nose and throat are signs of inadequate

ventilation. In such a case, immediately boost the ventilation of the work area, and if the

problem persists, stop the welding / cutting process completely.



• Use a suitable fume extraction system where welding / cutting works are being carried out. If

necessary, install a system that can expel fumes and gases accumulated in the entire workshop.

 



cadmium, zinc, coated or painted materials, use masks that provide fresh air in addition to the

above precautions.

• If the gas tanks are grouped in a separate zone, ensure that they are well ventilated, keep the

main valves closed when gas cylinders are not in use, pay attention to possible gas leaks.

• Shielding gases such as argon are denser than air and can be inhaled instead of air if used in

 

• Do not perform welding / cutting operations in the presence of chlorinated hydrocarbon vapors

released during lubrication or painting operations.

• Some welded / cut parts require special ventilation. The safety rules of products that require

special ventilation should be read carefully. A suitable gas mask should be worn when

necessary.

Fumes and Gases

May Be Harmful To

Your Health

Moving Parts May

Cause Injuries

Make sure all connections are tight, clean, and dry.

• Keep cables dry, free of oil and grease, and protected from hot metal and sparks.

• Bare wiring can kill. Check all cables frequently for possible damage. If a damaged or an

uninsulated cable is detected, repair or replace it immediately.

• Insulate work clamp when not connected to workpiece to prevent contact with any metal

object.

• Make sure that the grounding of the power line is properly connected.

 

• Use AC output ONLY if required for the welding process.

• If AC output is required, use remote output control if present on unit.

Additional safety precautions are required when any of the following electrically hazardous

conditions are present :

• in damp locations or while wearing wet clothing,

 

• when in cramped positions such as sitting, kneeling, or lying,

• when there is a high risk of unavoidable or accidental contact with the workpiece or ground.

For these conditions, use the following equipment in order presented:

• Semiautomatic DC constant voltage (CV) MIG welding machine,

• DC manual MMA welding machine,



EN

7

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i Safety Precautions

• Performing works such as welding / cutting, surface grinding, and brushing cause sparks and

metal particles to splatter. Wear approved protective work goggles which have edge guards

under the welding masks to prevent sustaining possible injuries.

Sparks and Spattering

Particles May Get

Into Eyes and Cause

Damage

• Do not touch the hot parts with bare hands.

• Wait until the time required for the machine to cool down before working on its parts.

 

 

Hot Parts May Cause

Severe Burns

 

• Protect other naked parts of your body (arms, neck, ears, etc.) with suitable protective clothing

from these rays.



so that people around you will not sustain injuries from arc rays and hot metals.

• This machine is not used for heating of icebound pipes. This operation performed with the

 

Arc Light May Damage

Your Eyes and Skin

• The noise generated by some equipment and operations may damage your hearing ability.

• Wear approved personal ear protective equipment if the noise level is high.

Noise May Cause

Damage To Your

Hearing Ability

• Do not apply welding / cutting operations into completely closed tanks or pipes.

• Before welding to tanks and closed containers, open them, completely empty them, and clean

them. Pay the greatest attention possible to the welding / cutting operations you will perform in

such places.

• Do not weld in tanks and pipes which might have previously contained substances that may

 

• Welding / cutting equipment heats up. For this reason, do not place it on surfaces that could

easily burn or be damaged !

• Do not point the torch towards any part of the body, other persons, or any metal while

unwrapping the welding / cutting wire.

• When welding wire is run manually from the roller especially in thin diameters the wire can slip

out of your hand, like a spring or can cause damage to you or other people around, therefore you

must protect your eyes and face while working on this.

Welding Wires Can

Cause Injuries



explosions.

• Before starting the welding / cutting work, remove these materials form the environment or cover

 

• National and international special rules apply in these areas.

Welding Operations

May Cause Fire and

Explosion

 

extinguishers tubes, water, and sand in easily accessible places.



circuits. Make sure that they are periodically inspected and pay attention that they run reliably.

• Electrical equipment should not be repaired by unauthorized persons.

Errors occurred if failed to do so may result in serious injury or death when using the

equipment.

• The gas circuit elements operate under pressure; explosions may occur as a result of services

provided by unauthorized persons, users may sustain serious injuries.

• It is recommended to perform technical maintenance of the machine and its auxiliary units at

least once a year.

Maintenance Work



Persons To Machines

and Apparatus May

Cause Injuries

EN

8

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45iSafety Precautions



operations, accompanied by another person.

• Avoid performing welding / cutting operations in such enclosed areas as much as possible.

• Take all necessary precautions when moving the machine. The areas where the machine to be

transported, parts to be used in transportation and the physical conditions and health of the

person carrying out the transportation works should be suitable for the transportation process.

• Some machines are extremely heavy; therefore, make sure that the necessary environmental

safety measures are taken when changing their places.

• If the machine is to be used on a platform, it must be checked that this platform has suitable load

bearing limits.

• If it is to be transported by means of a haulage vehicle (transport trolley, forklift etc.), make sure

of the durableness of the vehicle, and the connection points (carrying suspenders, straps, bolts,

nuts, wheels, etc.) that connect the machine to this vehicle.

• If the machine will be carried manually, make sure the durableness of the machine apparatuses

(carrying suspenders, straps, etc.) and connections.

• Observe the International Labor Organization’s rules on carriage weights and the transport

regulations in force in your country in order to ensure the necessary transport conditions.



from torches, cables or hoses. Be absolutely sure to carry gas cylinders separately.

• Remove all interconnections before transporting the welding / cutting equipment, each being

separately, lift and transport small ones using its handles, and the big ones from its handling

rings or by using appropriate haulage equipment, such as forklifts.

Welding / Cutting in





Failure To Take

Precautions During

Transport May Cause

Accidents



 

 

 

 

way that they would not tip over for sure.

• Allow operators to easily access settings and connections on the machine.

Falling Parts May

Cause Injuries Improper positioning of the power-supply sources or other equipment can cause serious injury

to persons and physical damage to other objects.

• Allow the machine to cool down according to operation cycle rates.

• Reduce the current or operation cycle rate before starting the welding / cutting again.

• Do not block the fronts of air vents of the machines.



Excessive Use Of The

Machine Causes

Overheating

Excessive Use Of The

Machine Causes

Overheating

• This device is in group 2, class A in EMC tests according to TS EN 55011 standard.

• This class A device is not intended for use in residential areas where electrical power is supplied

 

compatibility due to radio frequency interference transmitted and emitted in such places.

• Make sure that the work area complies with electromagnetic compatibility (EMC).

Electromagnetic interferences during welding / cutting operations may cause undesired effects

on your electronic devices and network; and the effects of these interferences that may occur

during these operations are under the responsibility of the user.

• If there is any interference, to ensure compliance; extra measures may be taken, such as the

use of short cables, use of shielded (armored) cables, transportation of the welding machine to

 

the work area under protection in terms of EMC.

• To avoid possible EMC damage, make sure to perform your welding / cutting operations as far

away from your sensitive electronic devices as possible (100 m).



connected to the low voltage network used in the home, the installer to make the

electrical connection or the person who will use the machine must be aware that

the machine has been connected in such a manner; in this case the responsibility

belongs to the user.

EN

9

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i Safety Precautions

• Ensure that your welding and/or cutting machine has been installed and situated in its place

according to the user manual.



Before installing the welding / cutting equipment, the person in charge of the operation and / or

the user must conduct an inspection of possible electromagnetic interference in the environment.

Aspects indicated below has to be taken into consideration;

a) Other supply cables, control cables, signal and telephone cables, above and below the welding

/ cutting machine and its equipment,

b) Radio and television transmitters and receivers,

c) Computer and other control hardware,

d) Critical safety equipment, e.g. protection of industrial equipment,

e) Medical apparatus for people in the vicinity, e.g. pacemakers and hearing aids,

f) Equipment used for measuring or calibration,

g) Immunity of other equipment in the environment. The user must ensure that the other

equipment in use in the environment is compatible. This may require additional protection

measures.

h) Considering the time during which the welding / cutting operations or other activities take

place during the day, the boundaries of the investigation area can be expanded according to the

size of the building, the structure of the building and other activities that are being performed

in the building.









• The appliance must be connected to the electricity supply in the recommended manner by a

 

 

tube or with an equivalent shielded cable. The housing of the power supply must be connected

and a good electrical contact between these two structures has to be provided.

• The recommended routine maintenance of the appliance must be carried out. All covers on the

body of the machine must be closed and / or locked when the device is in use. Any changes,

other than the standard settings without the written approval of the manufacturer, cannot be

 

possibly occur.



the work area, in a side by side manner. Welding / cutting cables should not be wound in any

way.



machine to pull metal parts on to itself. To avoid this attraction, make sure that the metal

 

interconnected metal materials.

• In cases where the workpiece cannot be connected to the ground due to electrical safety, or

because of its size and position (for example, in building marine vessel bodies or in steel

construction manufacturing), a connection between the workpiece and the grounding may

reduce emissions in some cases, it should be kept in mind that grounding of the workpiece may

cause users to sustain injuries or other electrical equipment in the environment to break down.

In cases where necessary, the workpiece and the grounding connection can be made as a direct

connection, but in some countries where direct connection is not permissible, the connection

can be established using appropriate capacity elements in accordance with local regulations

and ordinances.

• Screening and shielding of other devices and cables in the work area can prevent aliasing

 

applications.

Evaluation Of

Electromagnetic

Suitability Of The

Work Area

Electromagnetic

Interferance

Reduction Methods



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

Electromagnetic Field

(EMF)

EN

10

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45iSafety Precautions

• Choose the welding / cutting method and welding machine for the welding work you are to

perform.

• Select the welding / cutting current and/or voltage to match the material and thickness you are

going to weld.

• If you have to wait for a long time before you start your welding / cutting work, turn off the machine

after the fan has cooled it down. Our machines with smart fan control will turn off on their own.

• This device is not domestic waste. It must be directed to recycling within the framework of the

European Union directive and national laws.

• Obtain information from your dealer and authorized persons about the waste management of

your used machines.

Waste Procedure



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

• Welding / cutting and electric cables should not be wrapped around the body of the machine in

any way,

• The body of the machine should not get caught between the welding / cutting cables. The source

cables must be kept away from the body of the machine, both being placed side by side,

• The return cable must be connected to the workpiece as close as possible to the work area,

• The welding / cutting machine should not rest against the power unit, ensconce on it and not

work too close to it,

• Welding / cutting work should not be performed when carrying the wire supply unit or power

unit.

EMF may also disrupt the operation of medical implants (materials placed inside the body), such

as pacemakers. Protective measures should be taken for people who carry medical implants. For



conducted for welders. Risk assessment should be conducted and recommendations should be

made by a medical professional for users who carry medical implants.

• Do not expose the machine to rain, prevent the machine from splashing water or

pressurized steam.

Protection



WARRANTY FORM

Please visit our website www.magmaweld.com/warranty-form/wr for warranty form.

EN

11

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i

monoCUT 45ix and monoCUT 45i are high performance plasma cutting machines designed for cutting

and gouging applications. With its compact design, it is lightweight and portable. It offers excellent

cutting and gouging performance. In the monoCUT 45ix model, the gas pressure required during cutting

is automatically adjusted according to the cutting mode and the torch used. Whereas, in the monoCUT 45i

model, the required gas pressure must be adjusted manually.

Figure 1 : monoCUT 45ix Front and Back View

TECHNICAL INFORMATION

1.1 General Information

1.2 Machine Components

Technical Information

9

10

11

12

1

2

3

4

8

5

7

6

1- Handle

2- Digital Display

3- Torch Connector

4- Remote Control Connector

5- Adjustment Pot

6- Cutting Mode Selection Button

7- Current / Gas Selection Button

8- Grounding Connection (+)

9- Fan

10- Power Connection

11- Air Filter

12- On / Off Switch

EN

12

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45iTechnical Information

Figure 2 : monoCUT 45i Front and Back View

1- Handle

2- Manual Gas Pressure Display

3- Torch Connector

4- Remote Control Connector

5- Digital Display

6- Adjustment Pot

7- Cutting Mode Selection Button

8- Grounding Connection (+)

9- Fan

10- Power Connection

11- Gas Pressure Adjustment Pot

12- Air Filter

13- On / Off Switch

9

10

12

11

13

1

2

3

4

8

6

7

5

EN

13

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i

1.3 Product Label

Technical Information

X

U

I

U

U

S

I



Direct Current

Vertical Characteristic

Plasma Cutting



Suitable for Operation at

Hazardous Environments





     

should be kept idle for the machine cool down (zone 2).

Duty Cycle



6 min. 6 min.6 min.4 min. 4 min. 4 min. Time (min.)

Duty Cycle

Open Circuit Voltage

Rated Welding Current

Mains Voltage and Frequency

Protection Class

Rated Welding Voltage

Rated Power

Rated Mains Current

IP23S

EN

14

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45i

1.4 Technical Data



Rated Current

Protection Class

The cutting speeds in the table are the results of Magmaweld’s laboratory tests. It may vary according to different

cutting applications and environmental conditions.

Rated Power

Open Circuit Voltage

Recommended Cutting Thickness

(All metals)

Maximum Cutting Thickness

(All metals)

Breakout Thickness

(All metals)

Gouging

(3,5 mm D x 6,6 mm G)

Weight

Current Range

Dimensions (l x w x h)

1.5 Accessories

Technical Information

STANDARD ACCESSORIES QTY PRODUCT CODE

TECHNICAL DATA UNIT

V

VDC

mm

kg

kVA

ADC

kg

mm

monoCUT 45ix monoCUT 45i

230 230

45 45

14 14

IP23S IP23S

5,21 5,21

290

3,5 (1 Hour)

290

3,5 (1 Hour)

575 x 160 x 311 575 x 160 x 311

 

16 (525 mm/sec.)

22 (260 mm/sec.)

30 (130 mm/sec.)

16 (525 mm/sec.)

22 (260 mm/sec.)

30 (130 mm/sec.)

1

Workpiece Clamp and Cable

Torch (Hand Cutting)*

Consumable Kit (Hand Cutting)

Consumable Kit (Mechanized Cutting)

Torch (Mechanized Cutting) *



7142H10506

7942000450

7942100450

K301100343

7142M10512

EN

15

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i

INSTALLATION

2.1 Delivery Control

Make sure that all the materials you have ordered have been received. If any material is missing or damaged,

contact your place of purchase immediately.

The standard box includes the following;

 

• Torch and consumables • User manual

• Workpiece clamp and cable

In case of a damaged delivery, record a report, take a picture of the damage and report to the transport

company together with a photocopy of the delivery note. If the problem persists, contact the customer service.

2.2 Installation and Operation Recommendations

Symbols and their meanings on the device

Cutting / welding may be dangerous. Proper working conditions should be ensured and necessary

precautions should be taken. Specialists are responsible for the machine and have to be equipped with the

necessary equipment and those who are not relevant should be kept away from the cutting / welding area.



in homes, it is essential that the installer or the person who will operate the machine to make the electrical

connection has information on the machine’s connectivity. In this case the responsibility will be assumed

by the person who will perform the installation or by the operator.

The safety symbols and warning notes on the device and in the operating instructions must be observed

and the labels must not be removed.

Grids are intended for ventilation. The openings should not be covered in order to provide good cooling and

no foreign objects should be inserted.

• Lifting rings or forklifts should be used to move the machine. Place the power supply on a hard, level, smooth

surface where it will not fall or tip over.

• For a better performance, place the machine at least 30 cm away from the surrounding objects. Pay attention

to overheating, dust and moisture near the machine. Do not operate the machine under direct sunlight. If the

 

• Avoid cutting outdoors in windy and rainy weather circumstances. If cutting is necessary in such cases,

protect the cutting area and the cutting machine with a curtain and canopy.

• When positioning the machine, make sure that materials such as walls, curtains, boards do not prevent easy

access to the machine’s controls and connections.

• If you cut indoors, use a suitable fume extraction system. Use breathing apparatus if there is a risk of

 

              

damage the machine and this may invalidate the warranty.



• The power supply must be grounded in accordance with local and national electrical codes.



the gas cylinder so that it does not tip over.

Installation

EN

16

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45i

2.3 Mains Plug Connection

Never use the mains cable of the machine without a plug for your safety.

Protect the equipment with slow blow fuse appropriate for the system and with an

emergency switch that will quickly shut off the incoming electricity in an emergency.

• Use the appropriate ground cable for your power supply. Push the chassis connector into the connector on the

power supply and snap it in, make sure the connection is tight.

               

national regulations.

2.4 Connection to Mains

When plugging the power plug into the outlet, make sure that the power switch is set to “0”.

• Before connecting the machine to the mains, check the phase with a voltmeter. After making sure that phase is

correct, insert the plug into the socket.

• Start the machine by using the On/Off switch.

• The machine is ready to start after the MW symbol appears on the screen.

• Turn the machine off by turning the switch back to the “0” position.

2.5 Connections for Plasma Cutting

Be careful during the cutting process and wear appropriate protective clothing and gloves.

2.5.1 Gas Connections

• If the gas source is in the workshop or gas cylinder, a gas regulator should be used and this regulator should be

able to supply gas to the air inlet on the machine.

• If a gas cylinder is used, secure the gas cylinder to prevent it from tipping over.

• In order to work safely and achieve the best results, use a regulator that complies with standards and make sure

the gas supply quality is up to the standards. Gas supply quality will affect cutting performance and

consumption quality.

• Protect the gas line from contaminants such as oil, dust, etc.

• Keep the gas cylinder valve open for a while to allow possible sediment and particles to be discharged.

• Connect the gas regulator to the gas cylinder, make sure that the screw thread on the gas outlet of the gas

cylinder and the nut of the regulator overlap.

• Connect one end of the tube hose to the gas regulator and the other end to the gas inlet at the back of the

machine and open the gas cylinder valve.



• Make sure there are no leaks in the connections.



2.5.2 Grounding Pliers Connections

• Insert the plug of the ground clamp cable into the grounding socket on the machine and tighten it by turning it

to the right. Make sure the connection is made.



be cut.

Gas Source





Cutting : 185 l/min at 5.5 bar.

Gouging : 208 l/min at 4.6 bar.

Installation

EN

17

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i

The power supply must be grounded in accordance with national and local electrical

regulations to ensure personal safety, reduce electromagnetic interference, and create

appropriate operating conditions.



2.5.3 Torch Connections

• Magmaweld brand plasma cutting torches should be used

according to the cutting method to be used with the power

source.

• A manual torch is used for manual cutting, and

a mechanized torch for mechanized cutting.

• For the torch connection, insert the torch connector into its

connector on the power supply and turn it to the right.

Make sure the connection is completed.

• Keep the power supply off while connecting the torch.

• See 5.1 for detailed information on torches.

• The materials used for manual and mechanized plasma cutting torches are different from each other.

• First, the consumables of the torch must be prepared.

• Appropriate consumables should be selected according to the torch type and method used.

 

2.6 Placing Consumables

Swirl Ring

Electrode

Nozzle

Retaining Cap

Shield

Installation

EN

18

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45i

• The life of consumables depends on the material to be cut, cutting thickness, cutting length, cutting method,

appropriate distance to the material, air quality and blast frequency. If the frequency of blasting is high, the

consumable will wear out more quickly.

• When working with shielded consumables, the torch tip may touch the metal to be cut while cutting.

 

torch.

• See 5.1 for detailed information on consumables.

Plasma arc forms immediately when the torch trigger is pressed.

Make sure the power supply is turned off when replacing plasma consumables.

: It shows that the switch is above.

Remote control will only be activated when using a mechanized torch. There is a connector for remote

control at the back of the machine. When the necessary connection is made to the connector on the back

of the power supply, it provides access to the arc voltage and yields a signal for arc transfer and plasma

initiation. See 5.2 for detailed information on automation wiring diagram.

Voltage Divider Setting



Voltage information is changed with the help of the voltage divider. The voltage divider is set to 20:1 as

default. The table below shows the location of the DIP switches for voltage divider settings.

2.8 Remote Control

Ionized gas with high electrical conductivity is used in the plasma cutting process. The moment the plasma





is called pilot arc.

The pilot arc is forced out of the torch tip by high velocity gases. When it comes into contact with the metal

to be cut, the main current is formed and the cutting begins. The cutting process is continued by moving the

torch.

2.7 Pilot Arc

Installation

EN

19

www.magmaweld.com USER MANUAL

monoCUT 45ix / monoCUT 45i

It works with dry contact structure. The automation unit sends a warning to the plasma machine to operate

via the dry contact and the plasma creates a pilot arc. After the plasma machine creates a pilot arc, it sends a

warning to the automation unit with the dry contact structure. When the machine starts the cutting process,

it reports the plasma arc voltage for the automation interface to adjust the height.



The table contains information about the signals. The following table should be observed when the power

supply is to be connected to the CNC table or torch height controller with the machine interface cable:

Installation of the machine interface cable and voltage divider board assembly should be



When the cover on the interface connector on the back of the machine is not used, it should be

kept closed for keeping out dust and moisture.

Start (Trigger)

Arc Approval

Voltage Divider

Ground



Requires dry contact closure to activate.

Normally open contact. When the plasma arc forms, the contact switches

off. (Max. : 220 VDC 2A)

The machine adapts the output voltage to the control system. It gives

20:1, 21.1:1, 30:1, 40:1, 50:1 divided outputs.

For equipment safety, it is recommended to connect it to the grounding

point of your system.

P1, P3

P7 (+)



P6

P5, P2

Connection

Name Connector Pin Explanation

2.8.1 Communication

Installation

EN

20

www.magmaweld.comUSER MANUAL

monoCUT 45ix / monoCUT 45i

Digital Display

The adjusted welding current, pressure values, pressure graph and error codes can be

monitored visually on the digital screen.

It is used for cutting materials that consist of metal and gaps, such as grids. If this mode is not

used for cutting materials with gaps such as grids, material cutting starts when the pilot arc



after the gap, it is necessary to press and release the trigger again and start the pilot arc in

order to continue cutting. Grid cutting mode was created to be used on grid type materials.

A pilot arc occurs as soon as you press the torch trigger in the grid cutting and the material

is cut. It cuts the pilot arc when the gap is reached, and activates the pilot arc when it arrives

to the material part again. This cycle continues until you release the trigger.

The cutting process ends as soon as you release the trigger.

Pilot arc occurs as soon as you press the trigger in this mode. You can take your hand off the

trigger and continue the cutting process once you have started the cutting process.

Cutting Modes

As soon as you press the trigger in normal cutting mode, a pilot arc occurs and the cutting



arc goes out and you can release the trigger. If you release the trigger in the middle of the

material, the arc will go out again. The pilot arc reappears when you press the trigger again

to continue the process.

Grid Cut

Normal Cutting

Torch Trigger Lock

3.1 User Interface

OPERATION

Operation

Sayfa yükleniyor ...

Magmaweld MONOCUT 45i Plasma Cutting Mechanized El kitabı

Magmaweld MONOCUT 45i Plasma Cutting Mechanized El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler