Yamaha CRW2100ix Kullanım kılavuzu

Marka: Yamaha

Model: CRW2100ix

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Ave.

Buena Park, CA 90620

Telephone: 714-522-9011

Fax: 714-228-3913

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW2100IX

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment

generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product is found to be the source of interference, which can be

determined by turning the product OFF and ON , please try to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America,

6600 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

FCC INFORMATION

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780-787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.7mW (Continuous)

Write Mode: Max. 38mW

(for 166ns, Min. Cycle 86.6ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

LASER INFORMATION

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780-787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,7mW (kontinuierlich)

Schreibmodus: Max. 38mW

(für 166ns, Zyklusmin. 86,6ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780-787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,7mW (continue)

Mode de gravure: max. 38mW

(pour 166ns, cycle min. 86,6ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780-787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,7mW (continua)

Modo de escritura: máx. 38mW

(para 166ns, ciclo mínimo 86,6ns)

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

English

OWNER’S MANUAL

SAFETY PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

These precautions explain how to use the device correctly and safely, thereby preventing injury to

yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION

section, according to the likelihood and nature of any potential injuries or damage inflicted. They

relate to your personal safety, and also help you minimize the risk of damaging the device. Please

read these sections carefully before proceeding.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions

include, but are not limited to, the following:

● Do not open the device or attempt to disassemble or modify it.

Otherwise, there is an increased risk of electrical shock or fire. The device contains no user-

serviceable parts. If it appears to be malfunctioning, have it inspected by qualified service

personnel.

● Do not look inside the device.

If you expose your eyes to the laser inside the device, you risk damage or loss of your vision.

● Do not insert fingers or foreign objects into the device.

Otherwise, there is an increased risk of personal injury, electrical shock, damage to the device or

fire. Please take particular care if small children are present.

● Do not expose the device to rain, use it near water or in damp or wet conditions or place containers

on it that contain liquids which might spill into any openings.

Otherwise, there is an increased risk of electrical shock, fire or personal injury.

● Follow the Owner’s Manual carefully.

Otherwise, there is an increased risk of personal injury, electrical shock, fire or damage to the unit.

Follow the correct procedure when setting up the device.

● If unusual smells, sounds or smoke emanate from the device or if liquids enter the device, switch

the computer off immediately and unplug it from the power outlet.

Otherwise, there is an increased risk of electrical shock, fire or damage to the device. Return the

device immediately to the store at which it was purchased or alternatively, to the nearest Yamaha

dealer (listed at the back of this manual).

● Make sure the computer is electrically grounded.

Otherwise, there is an increased risk of electrical shock.

● When opening up the computer, always unplug the computer from the electrical outlet. Do not

touch the plug with wet hands.

Otherwise, there is an increased risk of electrical shock.

● When used in a fan-cooled system, the drive should not be exposed to temperatures outside the

range 5 ~ 35°C (41 ~ 95°F).

iii

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to

yourself or others, or damage to the instrument or other property. These precautions include, but

are not limited to, the following:

● Always unplug the computer from the electrical outlet if it will not be used for a prolonged period of

time or if there is a risk of lightning.

Otherwise, there is an increased risk of electrical shock, short-circuiting or fire.

● Do not expose the device to excessive heat or vibrations such as in direct sunlight or near a heater.

Also avoid placing it in extreme cold or much dust.

Otherwise, the front panel may become disfigured or the internal components may be damaged.

● Do not use the device near other electrical products such as televisions, radios or speakers.

Otherwise, this may cause interference which can affect the proper operation of those other

products.

● Do not place the device in an unstable position.

Otherwise, it may accidentally fall down and be damaged or cause personal injury.

● Mount the device horizontally.

Otherwise, written data may be destroyed. Set the device up according to the instructions in the

Owner’s Manual.

● Always remove the disc from the tray before transporting the device.

Otherwise, written data may be destroyed.

● When cleaning the device, never use benzene, paint thinners, detergents or chemical-impregnated

wiping cloths. Also, do not place vinyl, plastic or rubber objects on the device.

Otherwise, the device may be damaged or its front panel may become discolored. Use a soft, dry

cloth to wipe the device.

● Do not rest your weight on or place heavy objects on the device and do not use excessive force on

the buttons, switches or connectors.

Otherwise, there is an increased risk of damage to the device or personal injury.

● Do not listen to audio with headphones at high volume and for prolonged periods of time.

Otherwise, there is an increased risk of hearing loss.

● Before using the device, set the volume dial to its lowest setting.

Otherwise, sudden bursts of sound can cause hearing loss.

● Do not place the device near sources of magnetic interference, such as computer displays.

Magnetic interference can affect the operation and stability of the device.

● Have the device serviced regularly.

Otherwise, dust can build up inside the device, increasing the risk of fire or damage. For

information about servicing charges, contact the store at which the device was purchased or

alternatively, the nearest Yamaha dealer (listed at the back of this manual). The device should be

serviced about once a year.

■ About CD-R/RW discs

Please read the following regarding the handling of CD-R/RW discs.

1. Do not expose discs to excessive heat such as in direct sunlight or near a heater.

Also avoid keeping them in a humid place.

2. Do not touch disc surfaces.

When handling a disc, hold it by its edges.

3. Remove dust and dirt from disc surfaces.

Use air-based dust removers. The surfaces may be scratched if wiped with a dry cloth.

4. Do not stick labels on disc surfaces.

5. Do not write on disc surfaces except where indicated.

6. Do not clean discs with chemicals or detergents.

7. Do not bend or drop discs.

1. The information contained in this manual is subject to change

without prior notice.

2. All trademarks contained in this manual belong to their respective

owners.

3. Yamaha does not bear any responsibility for any outcome as a

result of using this device.

4. Reproduction of this manual, either in part or in full, is expressly

forbidden.

■ Precautions for Transportation

Before transporting the device, always put it in its original box. If the device is transported

without adequate packing, the internal components may be damaged and cause the device

to malfunction.

■ Copyrights

When writing to CD-R/RW, make sure that you are not infringing any copyrights. It is illegal

to copy audio CDs for non-personal use. When backing up software, please make sure that

you are not infringing any software copyrights for that product.

■ WARRANTY

YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR

ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS RECOMMENDED

THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN TO.

FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND SUPPLIERS

GUARANTEE THE RELIABILITY OF THE DISCS.

Table of Contents

This document may not, in whole or in part, be copied, photocopied,

reproduced, translated, transmitted or reduced to any electronic medium of

machine readable form without prior consent in writing from Yamaha.

Windows is a registered trademark of Microsoft Corporation.

Apple, Macintosh, Mac OS, and FireWire are registered trademarks of Apple

Computer, Inc.

i.LINK is a registered trademark of Sony Corporation.

All other trademarks are the property of their respective companies.

Introduction ....................................................................... 1

Features of the CRW2100IX Drive ................................................. 1

Before Use ......................................................................... 3

System Requirements ...................................................................... 3

Supported Discs .............................................................................. 5

Setup Flowchart .................................................................. 7

Windows Users ............................................................................... 7

Macintosh Users ............................................................................. 8

Setup Procedures ................................................................ 9

Serial Number ................................................................................. 9

Connections .................................................................................. 10

Connecting and Disconnecting IEEE1394 Devices ...................... 15

Verifying the Hardware Installation .............................................. 16

Operations ........................................................................ 18

Front Panel ................................................................................... 18

Rear Panel ..................................................................................... 19

Loading a Disc .............................................................................. 20

Ejecting a Disc .............................................................................. 20

Manually Ejecting a Disc in an Emergency .................................. 21

Troubleshooting ................................................................. 22

Appendix .......................................................................... 26

Writing Modes .............................................................................. 26

About the Firmware ...................................................................... 28

LED Indicator Messages................................................................ 29

CRW2100IX Specifications ........................................................... 30

Index ............................................................................................. 32

Introduction

Features of the CRW2100IX Drive

High speed

The CRW2100IX drive supports up to 16X speed writing of a CD-R disc, and up

to 10X speed writing of a CD-RW disc. For example, an audio CD (79 minutes/

700MB) can be created in approximately 5 minutes. With newly adopted Partial

CAV writing method (See the following column), you can write a disc by directly

transferring content data from a 32X-speed or faster CD-ROM drive. Data

reading at up to 40X speed is supported.

Easy setup

Implementation of an IEEE1394 interface (also known as FireWire or i.LINK)

eliminates the need for drive configurations (device ID, termination, and so on).

You can connect and start using the drive whenever you wish without restarting

your computer.

CD TEXT support

The CRW2100IX drive is compatible to CD TEXT format. Information such as

the song name or artist name can be recorded using writing software. The text

data on the disc you create can be displayed by a CD player that is compatible

with CD TEXT.

Wide compatibility

To ensure compatibility with a wide range of discs, technical data has been

exchanged with major disc manufacturers. 700MB discs are also supported.

High-fidelity audio

The CRW2100IX supports extracting digital audio data at up to 40X speed, as

well as recording digital sound with complete fidelity even when writing at 16X

speed.

Reliable writing

Yamaha’s proprietary Pure-Phase Laser System

improves jitter values

to allow

the signal to be recorded accurately. In addition, the 8MB buffer memory and

Running OPC

technology further enhance reliability.

Optimum speed

The CRW2100IX drive can write at an optimum speed

if the CD-R disc does not

allow 12X- or 16X-speed writing.

Introduction

*1. Pure-Phase Laser System (patent applied for)

Technology that reduces phase interference of the laser beam, so that it shines accurately on the disc.

*2. Jitter value

An important measure of recording quality. This has been improved 25% compared with Yamaha models

not using this technology.

*3. Running OPC

CD-R/RW discs vary by manufacturer in their recording characteristics, and the laser output required to

write data differs by disc. Running OPC is technology that solves this problem by automatically adjusting

the output of the laser according to the material of the disc on which data is being written.

*4 If you attempt to write at 16X or 12X speed but the CRW2100IX drive detects that the quality of a

target CD-R disc and other things are inappropriate for such speeds, the drive will automatically slow

down the writing speed optimally for the disc.

About IEEE1394

IEEE1394 is an industry standard approved by IEEE (Institute of Electrical and

Electronics Engineers). The serial interface has a broad bandwidth and is fast

enough to bidirectionally transfer large amounts of digital video and audio data

between electronic devices including computer peripherals. Also known as

FireWire and i.LINK, the IEEE1394 interface allows units to transfer data or

various controls over a single IEEE1394 interface cable. Unlike legacy serial

interfaces such as RS-232C, IEEE1394 allows a daisy-chaining (serial

connection) of devices and any two devices in the chain can transfer data to

each other. IEEE1394 also supports a tree (parallel) connection of devices. In

addition to this flexibility, IEEE1394 also eliminates the need for complicated

settings as found in SCSI (Small Computer System Interface), such as device ID

and termination. As of writing, IEEE1394 supports three different data transfer

rates: 100Mbps, 200Mbps, and 400Mbps.

About Partial CAV (Constant Angular Velocity)

Writing to a CD-R disc is normally done using CLV (Constant Linear Velocity)

method. In this method, the disc rotation speed will be so adjusted as to keep

a constant data transfer rate at any portion of the disc. In other words, the disc

rotation speed will vary in CLV writing.

In contrast, CAV (Constant Angular Velocity) method uses a constant disc

rotation speed at any portion of the disc whereas the data transfer rate will vary.

Because CAV method has an advantage to largely increase the data transfer rate

with a minimum load to the drive’s mechanism (compared to CLV’s rotation

speed adjustment), many of current CD-ROM drives use CAV method.

CD formats define the constant linear density of written data (data should be

written onto the disc track in the constant pitch) so that amount of recorded

data per disc rotation will increase as the writing point moves from the inner to

the outer. In other words, in CAV writing the outer portion has an increased

data transfer rate.

The CRW2100IX drive uses CAV method in the inner portions as well as CLV

method in the outer portions (Partial CAV) in order to enable up to 16X-speed

writing. The drive will control the disc rotation speed to start writing at 12X

speed in the inner portions, gradually accelerating up to 16X speed and

maintaining 16X speed in the outer portions.

Before Use

System Requirements

In order to use the CRW2100IX drive, your computer system will need to meet

the following set of requirements.

n The CRW2100IX drive may not write at a maximum speed depending on your

computer’s system configuration.

n For maximum performance, check your system setup (hardware, OS, and so on) for the

CD writing software.

Windows Users

● Computer

PC/AT-compatible computers

CPU: Pentium II, 300MHz or faster.

RAM: 64MB or more.

IEEE1394 port: At least one IEEE1394 port is required.

n This port may be a built-in (onboard) type, or provided with a PCI expansion card

or a CardBus card. If you newly install an IEEE1394 PCI or CardBus interface card,

your computer should have an empty PCI expansion slot or a CardBus slot. For

more information about the IEEE1394 interface card, refer to “IEEE1394 Interface

Card (PCI or CardBus)” shown below.

● Operating System (OS)

Windows 98 Second Edition, Windows Me, Windows 2000 Professional

● CD Writing Software

The CRW2100IX drive requires CD writing software to write onto a CD-R/RW

disc. When you use the CD writing software, make sure that it supports the

CRW2100IX drive.

n For details about how to install and use the software, refer to the documentation

that came with it.

● CD-ROM Drive

You may need another CD-ROM drive for any CD-related operations

(playback of an audio CD, installation from CD-ROM, and so on) until you

verify that the CRW2100IX is successfully installed. Also you may need

another CD-ROM drive if you are planning to copy a CD-ROM directly to a

CD-R/RW disc on the CRW2100IX drive.

n The CRW2100IX cannot boot your computer with a CD-ROM containing the

operating system, so that the unit cannot be used for installation of the operating

system.

● IEEE1394 Interface Card (PCI or CardBus)

For the CRW2100IX to work properly with your computer, your IEEE1394

interface card must be OHCI compliant. As of writing, Yamaha has verified

compatibility with following cards:

Manufacturer Product Card Type

Advansys ASB30400 PCI

SIIG NN2603 PCI

Before Use

n For latest information about approved IEEE1394 interface cards, check YAMAHA

CD-R/RW Drive web site at http://www.yamaha.co.jp/english/product/computer/.

n Some IEEE1394 interface cards may not work properly with your computer. If you

newly purchase and install the interface card, make sure of the compatibility not

only with your computer, but also with the CRW2100IX drive.

n If you already have an IEEE1394 interface card installed and working properly on

your computer, there might be cases of incompatibility with your new CRW2100IX

drive. In such cases, make sure that your computer system meets above

requirements, and also the interface card is compatible with the CRW2100IX drive.

Macintosh Users

● Computer

Macintosh computers with a built-in FireWire port

CPU: PowerPC G3, 300MHz or faster.

RAM: 64MB or more.

● Operating System

Mac OS 8.6, 9 or later.

n FireWire software version 2.2.2 or later is recommended for the CRW2100IX to

work properly. The latest software is available from Apple support web site.

● CD Writing Software

The CRW2100IX drive requires CD writing software to write to a CD-R/RW

disc. When you use the CD writing software, make sure that it supports the

CRW2100IX drive.

n For details about how to install and use the software, refer to the documentation

that came with it.

● CD-ROM Drive

You may need another CD-ROM drive for any CD-related operations

(playback of an audio CD, installation from CD-ROM, and so on) until you

verify that the CRW2100IX is successfully installed. Also you may need

another CD-ROM drive if you are planning to copy a CD-ROM directly to a

CD-R/RW disc on the CRW2100IX drive.

n The CRW2100IX cannot boot your computer with a CD-ROM containing the

operating system, so that the unit cannot be used for installation of the operating

system.

Hard Drive Space (Windows and Macintosh Users)

When writing to a CD-R/RW disc, you will need a working area (50 to 100MB

free space) on the hard drive. When creating an image file for all data to write to

a CD-R/RW disc, in addition to the working area, you will need as much hard

drive space as that data (up to 900MB in total). However, such hard drive space

for the image file is not needed when you are directly writing from a hard drive,

CD-ROM drive or so on (on-the-fly writing). In any case of writing to a CD-R/

RW disc, you will need a 50 to 100MB working area on your hard drive.

n Data is written to a disc much more reliably when writing from an image file,

eliminating the likelihood of errors occurring. Furthermore, this solution is ideal when

making multiple copies of discs since the original data is backed up in your hard drive as

an image file.

Before Use

Supported Discs

The CRW2100IX can write to discs that carry the following logos.

CD-R discs

The CRW2100E drive can write to these discs at 1X, 2X, 4X, 8X, 12X, or

16X speed. These discs can be played back in a CD-ROM drive or a CD

player.

n 16X-speed writing is enabled with Partial CAV method. (P. 2)

n When writing at 8X or faster speeds, use “high-speed writing capable”

discs.

CD-RW discs

There are two types of CD-RW discs: those that support write/rewrite

speeds of 1X, 2X, and 4X, and those that support only 2X. The

CRW2100E drive can write/rewrite at 2X or 4X speed on the first type of

disc and at 2X on the second type of disc. These discs can be read/

played on a device (e.g., CD-ROM drive) that supports “CD-RW.”

High Speed CD-RW discs

These discs allow writing/rewriting at 4X to 10X speeds. The

CRW2100E drive can write/rewrite these discs at 4X, 8X, or 10X speed.

These discs can be read/played by a CD-RW drive that bears the High

Speed CD-RW logo, or by a device (e.g., CD-ROM drive) that supports

“CD-RW.”

n 10X-speed writing is enabled with Full CAV method.

• In order to write, erase, or read these discs using a CD-R/

RW drive, a drive bearing the High Speed CD-RW logo must

be used. When using a CD-ROM drive to read these discs,

the drive must be capable of reading CD-RW discs.

• If these discs are used in a CD-R/RW drive not bearing the

High Speed CD-RW logo, the discs may not be recognized,

resulting in the computer not operating correctly or other

malfunctions occurring.

• Refer to the page at the URL below before attempting to read

these discs on a Yamaha CD-R/RW drive not bearing the

High Speed CD-RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

*1 Compatible with Orange Book Part 2.

*2 Compatible with Orange Book Part 3 Vol. 1.

*3 Compatible with Orange Book Part 3 Vol. 2.

n The Orange Book standard defines how all recordable discs (including CD-R and CD-

RW) are written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to

CD-RW discs. The standard was named after the color of the book’s pages.

Before Use

About CD-ROM

A CD-ROM disc is a compact disc containing high-density read-only data.

It has many applications, including the playback of music and video, the

archiving of data, as well as on-line documentation. The following are

descriptions of each CD-ROM format:

CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a

sampling rate of 44.1kHz for a 79 minutes disc.

Data CD: Up to 700 megabytes of computer data is stored in standard

ISO9660 format for a 700MB disc.

Video CD: These hold movies in which the video and audio data has been

compressed using MPEG-1 technology.

Setup Flowchart

The flowcharts below show the procedure for setting up the CRW2100IX drive.

For easy cross-referencing, each step includes relevant pages in this manual.

Windows Users

STEP

3-2

STEP

3-1

Yes

1 Turn your computer and the drive both

on (before connection).

2 Connect your computer and the

drive using an IEEE1394 interface

cable that came with the drive.

Make sure that system

configuration (CPU, RAM, OS and

so on) of your computer meets the

requirements of the CRW2100IX

drive

(P. 3).

Does your computer have a

built-in IEEE1394 port?

Set up the CRW2100IX drive (P. 10).

STEP

Make sure that the CRW2100IX

drive is correctly recognized

(P. 16).

Install the CD writing software.

STEP

Start using the CRW2100IX drive.

Do you have an appropriate

IEEE1394 interface card?

Install the card to

your computer.

Purchase an IEEE1394 card.

Use the drive to create an audio CD, to

backup data on your hard drive, or for

whatever purpose suits your needs.

The card should be known compatible

with your computer.

Read the documentation that

came with the card and properly

set up your computer.

n See page 3 for more information

about approved IEEE1394

interface cards that has been

tested in compatibility with the

CRW2100IX drive.

n You may need a different cable

depending on the IEEE1394 port

connector on your computer (P. 13).

n Before installing the software,

disconnect all IEEE1394 devices.

Setup Flowchart

Macintosh Users

STEP

1 Turn your computer and the drive both

on (before connection).

2 Connect your computer and the drive

using an IEEE1394 interface cable

that came with the drive.

Make sure that system

configuration (CPU, RAM, OS and

so on) of your computer meets the

requirements of the CRW2100IX

drive

(P. 4).

Set up the CRW2100IX drive (P. 10).

STEP

Make sure that the CRW2100IX

drive is correctly recognized

(P. 17).

Install the CD writing software.

STEP

Start using the CRW2100IX drive.

Use the drive to create an audio CD, to

backup data on your hard drive, or for

whatever purpose suits your needs.

Before using the drive, make sure that

the drive is recognized by MacOS and CD

writing software on your computer.

Setup Procedures

Serial Number

Once you have taken the CRW2100IX drive out of its packaging, you should

immediately note down the serial number found at the rear of the drive under the

bar code. You may need to refer to this number when requesting Customer

Support services. In the box below the following diagram, write down the 10-

character serial number (consisting of 3 letters followed by 7 digits).

Serial number

(3 letters and 7 digits)

Serial Number

Setup Procedures

Connections

Before connecting the CRW2100IX drive and the computer as described

below, make sure that you have installed appropriate CD writing software

(P. 3, 4). If you use Windows and in case newly install the CD writing

software, first disconnect all IEEE1394 devices from your computer. After

properly installing the software, you are ready to connect the devices. For

information about how to install the software, refer to the documentation

that came with it.

If your computer has no built-in IEEE1394 port, you will first need to install an

IEEE1394 interface card (purchased separately). For information about how to

install the card, refer to the documentation that came with it.

1 Make sure that the computer is turned on.

2 Make sure that the drive is turned OFF (the POWER switch is not

depressed).

Power ON Power OFF

3 Connect the supplied power cable to the AC IN socket on the drive’s rear panel.

Setup Procedures

4 Connect the other end of the power cable to an AC outlet.

n The power unit inside the CRW2100IX will automatically adjust itself to the local

voltage (100 to 240 volts).

5 Press the POWER switch on the drive’s front panel to turn the unit on.

n Confirm that the LED on the front panel flashes green and then shines steady

orange a moment after the power switch is turned on.

Sayfa yükleniyor ...

Yamaha CRW2100ix Kullanım kılavuzu

Marka: Yamaha

Model: CRW2100ix

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

PDF İndir

rapor

Diğer dillerde

français: Yamaha CRW2100ix Manuel utilisateur
italiano: Yamaha CRW2100ix Manuale utente
svenska: Yamaha CRW2100ix Användarmanual
Deutsch: Yamaha CRW2100ix Benutzerhandbuch
English: Yamaha CRW2100ix User manual
dansk: Yamaha CRW2100ix Brugermanual
Nederlands: Yamaha CRW2100ix Handleiding
română: Yamaha CRW2100ix Manual de utilizare

İlgili Makaleler

Diğer Belgeler

Konica Minolta bizhub 20 El kitabı