Yamaha P50 Kullanım kılavuzu

Marka: Yamaha

Modeli: P50

Kategori: Müzik Enstrümanları

Tip: Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

P50-m

FCC INFORMATION (U.S.A)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly

approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential

environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found in the user’s manual, may cause interference harmful to the operation of other

electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product

is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem

by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to

co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the your local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

NEDERLAND

NETHERLAND

● Dit apparaat bevat een lithium batterij voor geheugen back-up.

● This apparatus contains a lithium battery for memory back-up.

● Raadpleeg uw leverancier over de verwijdering van de batterij

op het moment dat u het apparaat aan het einde van de

levensduur afdankt of de volgende Yamaha Service Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

● For the removal of the battery at the moment of the disposal at

the end of the service life please consult your retailer or Yamaha

Service Center as follows:

Yamaha Music Nederland Service Center

Address : Kanaalweg 18-G, 3526 KL UTRECHT

Tel : 030-2828425

● Gooi de batterij niet weg, maar lever hem in als KCA.

● Do not throw away the battery. Instead, hand it in as small

chemical waste.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og

type. Levér det brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma

batterityp eller en ekvivalent typ som rekommenderas av

apparattillverkaren. Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power sup-

ply or adapter other than one described in the manual, on

the name plate, or specifically recommended by Yamaha.

WARNING: Do not place this product in a position where

anyone could walk on, trip over, or roll anything over

power or connecting cords of any kind. The use of an

extension cord is not recommended! If you must use an

extension cord, the minimum wire size for a 25' cord (or

less ) is 18 AWG. NOTE: The smaller the AWG number,

the larger the current handling capacity. For longer exten-

sion cords, consult a local electrician.

This Product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by

Yamaha. If a cart, etc., is used, please observe all safety

markings and instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO CHANGE: The in-

formation contained in this manual is believed to be correct

at the time of printing. However, Yamaha reserves the right

to change or modify any of the specifications without no-

tice or obligation to update existing units.

This product, either alone or in combination with an ampli-

fier and headphones or speaker/s, may be capable of produc-

ing sound levels that could cause permanent hearing loss.

DO NOT operate for long periods of time at a high volume

level or at a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should consult

an audiologist. IMPORTANT: The louder the sound, the

shorter the time period before damage occurs.

Some Yamaha products may have benches and/or acces-

sory mounting fixtures that are either supplied with the

product or as optional accessories. Some of these items are

designed to be dealer assembled or installed. Please make

sure that benches are stable and any optional fixtures

(where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only.

No other uses are recommended.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the manu-

facturer’s warranty, and are therefore the owners responsi-

bility. Please study this manual carefully and consult your

dealer before requesting service.

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes neces-

sary, contact a qualified service representative to perform

the replacement.

This Product may also use “household” type batteries.

Some of these may be rechargeable. Make sure that the

battery being charged is a rechargeable type and that the

charger is intended for the battery being charged.

When installing batteries, do not mix old batteries with

new, or with batteries of a different type. Batteries MUST

be installed correctly. Mismatches or incorrect installation

may result in overheating and battery case rupture.

Warning: Do not attempt to disassemble, or incinerate any

battery. Keep all batteries away from children. Dispose of

used batteries promptly and as regulated by the laws in

your area.

Note: Check with any retailer of household type batteries

in your area for battery disposal information.

Disposal Notice: Should this Product become damaged be-

yond repair, or for some reason its useful life is considered

to be at an end, please observe all local, state, and federal

regulations that relate to the disposal of products that con-

tain lead, batteries, plastics, etc. If your dealer is unable to

assist you, Please contact Yamaha directly.

NAME PLATE LOCATION: The name Plate is located

on the top of the product. The model number, serial

number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and

the date of purchase in the spaces provided below and

retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

92-BP

PLEASE KEEP THIS MANUAL

WELCOME TO THE P50-m

Welcome to the P50-m

Congratulations and thank you for purchasing the Yamaha

P50-m Piano Tone Generator!

The P50-m is an advanced tone generator with piano and

other keyboard Voices. It provides exceptionally realistic and

high-quality piano Voices — with complete 32-note polyphony —

when connected to a MIDI keyboard or when used with a

sequencer or computer. Reverb and Chorus effects are also built

into the Voices for a rich, natural sound.

The P50-m gives you easy and intuitive control over the

sound, including Brightness, Reverb Send, fine and coarse tuning,

and touch sensitivity. Convenient EQ sliders on the panel let you

adjust the timbre in real time. Other special controls such as

Program Change Table and MIDI OUT ensure easy and trouble

free operation when using the P50-m in General MIDI applica-

tions and with additional tone generators. What’s more, you can

combine two P50-m units together (using the Receive Mode

control) for full 64-note polyphony.

UNPACKING

Unpacking

Your P50-m package should include the items listed below. Make

sure that you have them all. Also, write down the serial number

of your P50-m in the box below, for future reference.

• P50-m

Serial No.:

• PA-3B AC Adaptor

• Owner’s Manual

iii

TABLE OF CONTENTS

Table of Contents

Welcome to the P50-m ......................................................................................................... i

Unpacking............................................................................................................................... ii

Table of Contents................................................................................................................. iii

How to Use This Manual .....................................................................................................iv

Precautions ............................................................................................................................ v

The Controls of the P50-m .................................................................................................1

Front Panel.......................................................................................................................... 1

Rear Panel ...........................................................................................................................3

Setting Up and Playing Your P50-m ................................................................................. 4

What You’ll Need ........................................................................................................... 4

Making the Connections................................................................................................4

Using in Larger MIDI Systems ....................................................................................... 6

Powering Up and Playing the Demo Song ....................................................................6

Powering Up ............................................................................................................ 7

Playing the Demo Song ........................................................................................... 7

Playing all Demo Songs ...........................................................................................8

OPERATION GUIDE

Voice Controls.....................................................................................................................9

Selecting a Voice ........................................................................................................... 9

Selecting Voices From Your MIDI Keyboard...............................................................10

Tone Controls....................................................................................................................11

Changing the Brightness of a Voice ............................................................................11

Changing the Reverb Send for a Voice........................................................................12

3-Band EQ Sliders.............................................................................................................13

Tune Controls....................................................................................................................14

Changing the Master Tune Setting ..............................................................................14

Changing the Note Shift Setting..................................................................................15

Utility Controls ..................................................................................................................16

Changing the Touch Sensitivity ...................................................................................16

Changing the MIDI Receive Channel...........................................................................17

Advanced Functions ..........................................................................................................18

Program Change Table................................................................................................18

Changing the Device Number......................................................................................19

Receive Mode ..............................................................................................................20

Changing the MIDI OUT Setting .................................................................................21

Factory Set ..................................................................................................................22

APPENDIX

Troubleshooting.................................................................................................................23

Error Messages ..................................................................................................................25

Specifications ....................................................................................................................26

Index................................................................................................................................. 27

SOUND LISTS & MIDI DATA

Voice List...........................................................................................................................30

Effect Lists.........................................................................................................................31

MIDI Data Format .............................................................................................................33

MIDI Implementation Chart...............................................................................................42

HOW TO USE THIS MANUAL

How to Use This Manual

You are probably eager to play your new P50-m Piano Tone

Generator right away, rather than have to read through a lot of

instructions before you can even get a sound out of it.

However, to get the most out of your P50-m, we strongly

suggest that you read the following sections in the order given:

1) Precautions

This gives you important information on how to care for

your new P50-m, how to avoid damaging it, and how to

ensure long-term, reliable operation.

2) The Controls of the P50-m

This section introduces you to the panel controls and

connectors.

3) Setting Up and Playing Your P50-m

This very important section gets you started using your

P50-m. It guides you in connecting and setting up the

instrument for different example systems, and shows you

how to play the special Demo song.

4) Operation Guide

Once you’re familiar with everything above, go over this

comprehensive guide to all P50-m functions. You won’t

need (or want) to read everything at once, but it is there for

you to refer to when you need information about a certain

feature or function.

5) Appendix

Finally, use the sections in the Appendix as necessary.

Specifically, if you run into some problem or difficulty, refer

to the Troubleshooting section for help.

PRECAUTIONS

Precautions

Your P50-m will give you years of reliable service if you follow

the simple precautions below:

■ LOCATION

Keep the instrument away from locations where it is likely to be

exposed to high temperatures (such as direct sunlight) or

humidity. Also avoid locations which are subject to excessive dust

accumulation or vibration which could cause mechanical damage.

■ USE THE CORRECT POWER ADAPTOR

Use only the recommended PA-3B or PA-1207 Power Adaptor

for supplying power to the instrument. Use of another adaptor

may cause serious damage to the instrument or the adaptor itself.

■ MAKE SURE POWER IS OFF WHEN MAKING OR REMOVING

CONNECTIONS

To prevent damage to the instrument and other connected

equipment, always turn off the power prior to connecting or

disconnecting cables. Also, turn the power off when the instru-

ment is not in use, and disconnect the power adaptor during

electric storms.

■ HANDLE THE INSTRUMENT WITH CARE

Although the instrument has been constructed to withstand the

rigors of normal use for optimum sturdiness and reliability, avoid

subjecting it to strong physical shocks (such as dropping or hitting

it). Since the P50-m is a precision-made electronic device, also

avoid applying excessive force to the various controls. When

moving the instrument, first unplug the power adaptor and all

other cables to prevent damage to cords and jacks. Always unplug

cables by gripping the plug firmly, not by pulling on the cable.

■ CLEAN WITH A SOFT, DRY CLOTH

Never use solvents such as benzine or thinner to clean the

instrument, since these will damage the panel finish. Wipe clean

with a soft, dry cloth. If necessary, use a soft, clean, slightly

moistened cloth — making sure to wipe the case off again with a

dry cloth.

PRECAUTIONS

■ ELECTROMAGNETIC INTERFERENCE

Avoid using the unit near televisions, radios or other equipment

generating electromagnetic fields. Proximity to such equipment

may cause the unit to malfunction, and may generate

interference noise in the other appliance as well.

■ DO NOT OPEN THE CASE OR TRY REPAIRING THE INSTRUMENT

YOURSELF

The instrument contains no user-serviceable parts. Never open

the case or tamper with the internal circuitry in any way, since

doing so may result in damage to the instrument. Refer all

servicing to qualified Yamaha service personnel.

■ MIDI CABLES

When connecting the instrument to other MIDI equipment, be

sure to use only high-quality cables made especially for MIDI data

transmission. Also, avoid using cables longer than 15 meters,

since long cables can result in data errors.

Yamaha is not responsible for damage caused by improper

handling or operation.

THE CONTROLS OF THE P50-m

The Controls of the P50-m

Front Panel

1 POWER/VOL control

Pressing this turns the power on and off. Turning it adjusts the overall

volume of the P50-m.

2 PHONES jack

For connection to a set of stereo headphones (mini-pin).

3 VOICE SELECT button

For selection of the internal Voices. (See page 9.) Also for changing

the Program Change Table setting. (See page 18.)

TONE Controls

4 BRIGHT button

For adjusting the brightness of the selected Voice. (See page 11.)

5 REVERB SEND button

For adjusting the amount of sound processed with the Reverb effect.

(See page 12.)

THE CONTROLS OF THE P50-m

TUNE Controls

6 MASTER TUNE button

For adjusting the overall fine tuning of the instrument. (See page 14.)

Also used with the NOTE SHIFT button for playing the Demo song.

(See page 7.)

7 NOTE SHIFT button

For changing the key transposition setting of the instrument. (See

page 15.) Also used with the MASTER TUNE button for playing the

Demo song. (See page 7.)

UTILITY Controls

8 TOUCH button

For changing the touch (velocity) response of the instrument. (See

page 16.) Also for changing the Device Number setting. (See page

19.) Also used with the MIDI CH button for changing the Receive

Mode of the instrument. (See page 20.)

9 MIDI CH (Channel) button

For setting the MIDI Receive channel for the instrument. (See page

17.) Also for setting the MIDI OUT setting. (See page 21.) Also used

with the TOUCH button for changing the Receive Mode of the

instrument. (See page 20.)

10 LED display

11 DATA dial

For adjusting values or changing settings of the various parameters.

12 EQ sliders (LOW, MID, HIGH)

For making fine changes to the tonal quality of the sound. (See page

13.)

6 8

7 9

THE CONTROLS OF THE P50-m

Rear Panel

1 MIDI OUT/IN terminals

For connection to other MIDI devices, such as a MIDI keyboard, tone

generator, sequencer, or to a computer that has a MIDI interface.

(See pages 4–6 for more information on MIDI connections.)

2 DC IN jack

For connection to the PA-3B AC power adaptor.

3 OUTPUT R, L/MONO jacks (Right, Left/Mono)

For connection to a stereo amplifier/speaker system. When using a

mono system, connect it to the L/MONO jack.

SETTING UP AND PLAYING YOUR P50-m

Setting Up and Playing Your

P50-m

In this section, you’ll learn how to set up the P50-m for use with

a MIDI keyboard. You’ll also learn how to set it up for use with a

computer or sequencer and a second tone generator. Finally,

you’ll learn how to play the Demo song and hear the realistic and

dynamic Voices of the P50-m.

What You’ll Need

❏ The P50-m and the included power adaptor.

❏ A MIDI keyboard, electronic piano, or any instrument that can

output MIDI data.

❏ An amplifier/speaker system, preferably stereo. Alternately, you

can use a set of stereo headphones.

❏ Audio connecting cables.

❏ A MIDI cable.

Making the Connections

Before making any connections, make sure that all equipment to

be connected is turned off, and that the P50-m power adaptor is

not connected to an electrical outlet.

Connect one end of the MIDI cable to the MIDI OUT

terminal of the MIDI keyboard and the other to the MIDI IN

terminal of the P50-m (as shown in the illustration below).

Also, make sure that the MIDI send channel on the

keyboard and the MIDI Receive Channel on the P50-m (see

page 17) are set to the same value. (Refer to the owner’s

manual of the MIDI keyboard if necessary.)

Connect the audio cables from the R and L/MONO OUTPUT

jacks of the P50-m to the appropriate inputs on the amplifier

speaker system (as shown in the illustration below).

If the amplifier has only one input, use the L/MONO jack

on the P50-m. If you are using stereo headphones,

connect them to the front panel PHONES jack.

Connect the power adaptor to the DC IN terminal on the

P50-m and plug the adaptor into an appropriate electrical

outlet.

SETTING UP AND PLAYING YOUR P50-m

MIDI Keyboard

MIDI OUT

MIDI IN

MIDI CABLE

Amplifier

Speaker System

PHONES

DC INL/MONO

Power

Adaptor

• Do not attempt to use an AC adaptor other than the PA-3B or

PA-1207. The use of an incompatible adaptor may result in

irreparable damage to the P50-m, and even pose a serious shock

hazard.

• Be sure to disconnect the power adaptor from the outlet when

the P50-m is not in use.

SETTING UP AND PLAYING YOUR P50-m

Using in Larger MIDI Systems

The P50-m is equipped with MIDI IN and OUT terminals,

allowing you to use it in any MIDI system. In the system example

shown below, the P50-m is connected to both a computer and

another tone generator. Here, the computer (with sequencer or

other music software) plays back song data using the Voices of

the P50-m and the connected tone generator.

In systems such as this, you should make sure that:

• The MIDI Receive Channel on the P50-m (see page 17) is set

to the same channel as that for the piano part (or track) on

the software.

• The MIDI OUT Mode is set to “ot2.” (See page 21.) This

ensures that the piano part data will play the Voices of the

P50-m, and not the other tone generator.

Also, if you are using General MIDI (GM) compatible software,

set the Program Change Table to “on.” (See page 18.) This

ensures that the Voices on the P50-m will match the intended

program changes in the software.

Powering Up and Playing the

Demo Song

Once you’ve connected everything properly, you’re ready to turn

the P50-m on and start playing it. However, a small word of

caution before you begin: Follow the instructions given below to

avoid possible damage to your equipment and speakers.

Computer

MIDI Interface

Tone GeneratorP50-m

SETTING UP AND PLAYING YOUR P50-m

Powering Up

If you haven’t done so already, press the POWER/VOL

control on the P50-m.

Turn on the power of your MIDI keyboard.

Make sure that all volume controls (on the P50-m and the

connected amplifier) are turned down. Then, turn on the

power of your amplifier speaker system.

Finally, set the volume control on the P50-m to about the

midway position initially (you can raise it later if needed),

and set the volume on the amplifier to a suitable level.

Playing the Demo Song

Now that you’ve set everything up properly, try playing the built-

in Demo Song. This showcases the high-quality Voices and the

AWM2 tone generation system of the P50-m.

Simultaneously press the MASTER TUNE and NOTE SHIFT

buttons.

The Demo song for the selected Voice starts playing

immediately and repeats indefinitely until stopped (by pressing

any panel button). (The LEDs and lamps flash in a pattern dur-

ing playback.)

More about Demo Song

There are actually two Demo Song modes. In the Single

Demo Play mode (described above), the currently selected

Voice is used for the Demo song. Each Voice has its own

Demo song, specially programmed to suit and showcase

that particular Voice.

In the All Demo Play mode (described below), all Demo

songs can be played back in succession.

SETTING UP AND PLAYING YOUR P50-m

Playing all Demo Songs

With the power off, simultaneously hold down the

MASTER TUNE and NOTE SHIFT buttons and turn the

power on.

Demo song number 1 (for Voice 01) starts playing

immediately and is followed by the other Demo songs in

succession. Playback of all songs repeats indefinitely until

stopped (by pressing any panel button). (The LEDs and

lamps flash in a pattern during playback.)

Using the All Demo Play mode resets the P50-m to the original

factory settings. If you have made custom settings that you want

to keep, make a note of them before using All Demo Play.

Hold down

Push (power off)

OPERATION GUIDE

Operation Guide

Voice Controls

Selecting a Voice

The P50-m has 28 different piano and other keyboard Voices.

(See list on page 30.) These can be selected either from the

panel controls or remotely from a connected MIDI device.

Range: 01 — 29

Press the SELECT button.

Use the DATA dial to change the Voice number.

Play this new Voice from the connected keyboard (or other

device). Try selecting other Voices and playing them as well.

(For a list of all available Voices, see page 30.)

The polyphony (maximum simultaneous notes) of the P50-m is 32.

However, for two-layered Voices (see page 30), this is reduced to 16.

Voice number (program number)

Lamp lights.

OPERATION GUIDE

Selecting Voices From Your MIDI

Keyboard

You can also select Voices remotely from a connected MIDI key-

board. Though the actual operation may differ depending on the

keyboard used, the general procedure is the same. (Refer to the

owner’s manual of your instrument for specific instructions.)

Make sure that your keyboard is set up to send Program

Change messages.

Use your keyboard’s panel controls to select a program.

Generally, if everything has been set up properly, the Voice

number on the P50-m will change, and will be the same

number as the program number you selected on your key-

board.

• Keep in mind that the Voices of the P50-m number up to 29. Program

change numbers higher than 28 select only the highest Voice (#29).

• Depending on the MIDI device you are using, the program numbers

(on the device) may not match the Voice numbers on the P50-m. This

is because the numbering system of some MIDI devices starts at #00,

rather than #01. In such a case, for example, you would use program

#12 to select Voice 13 on the P50-m.

OPERATION GUIDE

Tone Controls

The Tone controls of the P50-m, BRIGHT and REVERB SEND,

let you adjust the sound of individual Voices. Brightness

(BRIGHT) determines the tonal quality of the Voice, while Reverb

Send determines how much Reverb effect is applied to the

selected Voice.

Both of these controls let you make independent settings for

different Voices, and all settings are automatically saved as they

are made.

Changing the Brightness of a Voice

Lower values produce a soft, mellow sound, while higher values

produce a bright, crisp sound. The normal setting is 00.

Range: –64 — 63

Press the BRIGHT button.

Use the DATA dial to change the Brightness setting.

Lamp lights.

Brightness setting for the currently selected Voice.

Sayfa yükleniyor...

Yamaha P50 Kullanım kılavuzu

Marka: Yamaha

Modeli: P50

Kategori: Müzik Enstrümanları

Tip: Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

P50-m

PDF''yi indir

rapor

diğer dillerde

español: Yamaha P50 Manual de usuario
français: Yamaha P50 Manuel utilisateur
italiano: Yamaha P50 Manuale utente
svenska: Yamaha P50 Användarmanual
čeština: Yamaha P50 Uživatelský manuál
polski: Yamaha P50 Instrukcja obsługi
Deutsch: Yamaha P50 Benutzerhandbuch
português: Yamaha P50 Manual do usuário
English: Yamaha P50 User manual
dansk: Yamaha P50 Brugermanual
русский: Yamaha P50 Руководство пользователя
suomi: Yamaha P50 Ohjekirja
Nederlands: Yamaha P50 Handleiding
română: Yamaha P50 Manual de utilizare

Yamaha P50 Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha P50 Kullanım kılavuzu

diğer dillerde

İlgili makaleler