Yamaha A-S301 Kullanım kılavuzu

Marka: Yamaha

Model: A-S301

Kategori: Ses amplifikatörleri

Tip: Kullanım kılavuzu

Integrated Amplifier

Amplificateur Intégré

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

Printed in Malaysia ZM52720

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

Integrated Amplifier

Amplificateur Intégré

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 30 cm

Rear: 20 cm

Sides: 20 cm

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to an AC wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the AC wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from an AC wall

outlet or this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the AC wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press A (power) to set this unit

to standby mode, and then disconnect the AC power plug

from the AC wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

This label is required to be attached to a product of which

the temperature of the top cover may be hot during

operation.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed,

as a plug with bared flexible cord is hazardous if engaged

in a live socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as

it is connected to the AC wall outlet, even if this unit itself is turned

off by A. This state is called the standby mode. In this state, this

unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth terminal of the

three pin plug.

1 En

English

USEFUL FEATURES ................................... 1

SUPPLIED ACCESSORIES......................... 1

CONTROLS AND FUNCTIONS................. 2

Front panel ........................................................2

Rear panel .........................................................4

Remote control..................................................6

CONNECTIONS............................................ 9

Connecting speakers and source components...9

Connecting power cable..................................10

PLAYBACK................................................. 11

Playing a source ............................................. 11

Adjusting to the desired sound....................... 12

TROUBLESHOOTING.............................. 13

SPECIFICATIONS ..................................... 15

This unit allows you to:

◆ Enjoy the highest sound quality of compact discs by

using the CD direct function (A-S701 only)

(see page 12)

◆ Enjoy pure, high fidelity sound by using the Pure

Direct function (see page 12)

◆ Save power by using AUTO POWER STANDBY

switch (see page 4)

◆ Use the remote control of this unit to operate a Yamaha

tuner and/or CD player (see page 7)

◆ Boost bass sounds by connecting a subwoofer

(see page 9)

Please check that you received all of the following parts.

CONTENTS

About this manual

• y indicates a tip for your operation.

• The illustrations used in this Owner’s Manual are A-S701.

• Depending on the model, there are some countries/regions where it may not be sold.

USEFUL FEATURES

SUPPLIED ACCESSORIES

Remote control Batteries (x2)

(AA, R6, UM-3)

Power cable

(A-S701 only)

2 En

1 A (power) switch

Turns on and off the power of this unit.

Even when this unit is turned off, this unit consumes a small

amount of power.

2 Power indicator

3 Remote control sensor

Receives infrared signals from the remote control.

4 PHONES jack

Connect your headphones.

5 SPEAKERS selector

6 BASS control

Increases or decreases the low frequency response.

The 0 position produces a flat response.

Control range: –10 dB to +10 dB

7 TREBLE control

Increases or decreases the high frequency response.

The 0 position produces a flat response.

Control range: –10 dB to +10 dB

CONTROLS AND FUNCTIONS

Front panel

(A-S701)

Note

Indicator Status

Brightly lit The power of this unit is “on”.

Dimly lit

This unit is in “standby” mode.

For details on the “standby” mode, see

page 6.

Off The power of this unit is “off”.

Selector

position

Speaker status

OFF Both sets of speakers are off.

A or B

The set of speakers connected to the A

or B terminals is on.

A+B BI-WIRING Both sets of speakers are on.

CONTROLS AND FUNCTIONS

3 En

English

8 BALANCE control

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances.

If you rotate the BALANCE control to the end of L (left) or

R (right), the opposite side of channel is muted.

9 LOUDNESS control

Retain a full tonal range at any volume level

(see page 12).

0 INPUT selector and indicators

Selects the input source you want to listen to. The

input source indicators light up when the

corresponding input sources are selected.

The input source names correspond to the names of the

connection jacks on the rear panel.

A VOLUME control

Increases or decreases the sound output level.

B CD DIRECT AMP button and indicator

(A-S701 only)

Reproduces CD sound in the highest signal quality

(see page 12).

The indicator above it lights up when this function is

turned on.

C PURE DIRECT button and indicator

Reproduces any input source in the purest sound

possible (see page 12).

The indicator above it lights up when this function is

turned on.

(A-S701)

Note

CONTROLS AND FUNCTIONS

4 En

1 CD input jacks

Used to connect a CD player (see page 9).

2 PHONO jacks and GND terminal

Used to connect a turntable that uses an MM cartridge,

and to ground the terminal (see page 9).

3 Audio input/output jacks

Used to connect external components, such as a tuner,

etc (see page 9).

4 DIGITAL (OPTICAL) jack

Used to connect a component with a digital optical

output (see page 9).

5 DIGITAL (COAXIAL) jack

Used to connect a component with a digital coaxial

output (see page 9).

6 DC OUT jack

For supplying power to a Yamaha AV accessory. For

details on connections, refer to the instruction manual

of the AV accessory.

7 SPEAKERS A/B terminals

Used to connect one or two speaker sets (see page 9).

8 SUBWOOFER OUT jack

Used to connect a subwoofer with built-in amplifier

(see page 9).

The SUBWOOFER OUT jack attenuates signals over 90 Hz.

9 AUTO POWER STANDBY switch

Rear panel

(A-S701)

(A-S501/S301)

Switch

position

Status

The unit enters standby mode

automatically if not operated for 8

hours.

OFF

The unit does not enter standby mode

automatically.

CONTROLS AND FUNCTIONS

5 En

English

0 VOLTAGE SELECTOR (General model only)

Used to set to your local main voltage (see page 10).

A IMPEDANCE SELECTOR switch

Do not change the IMPEDANCE SELECTOR switch

while the power is turned on, as doing so may damage

the unit.

If the IMPEDANCE SELECTOR switch may not be

fully slid to either position, remove the power cable

and slide the switch all the way to either position.

Select the switch position according to the impedance

of the speakers.

B AC IN (A-S701)

Used to connect the supplied power cable to an AC

wall outlet (see page 10).

Power cable (A-S501/S301)

Used to connect this unit to an AC wall outlet

(see page 10).

(A-S701)

(A-S501/S301)

CAUTION

Speaker

connection

Speaker

impedance

Switch

position

SPEAKERS A

SPEAKERS B

6 Ω or higher HIGH

4 Ω or higher LOW

SPEAKERS A

and

SPEAKERS B

12 Ω or higher HIGH

8 Ω or higher LOW

Bi-wiring

6 Ω or higher HIGH

4Ω or higher LOW

CONTROLS AND FUNCTIONS

6 En

1 Infrared signal transmitter

Sends infrared signals.

2 A AMP

Turns this unit on, or sets it to standby mode.

3 OPEN/CLOSE

Opens/closes the disc tray of the Yamaha CD player.

Refer to the owner’s manual of your CD player for

details.

Even when using a Yamaha CD player, certain components

and features may not be available.

4 A CD

Turns the Yamaha CD player on, or sets it to standby

mode. Refer to the owner’s manual of your CD player

for details.

Even when using a Yamaha CD player, certain components

and features may not be available.

5 CD DIRECT AMP (A-S701 only)

Reproduces CD sound in the highest signal quality

(see page 12).

6 Input selector buttons

Selects the input source you want to listen to.

The input source names correspond to the names of the

connection jacks on the rear panel.

Remote control

(A-S501/S301)(A-S701)

Note

CONTROLS AND FUNCTIONS

7 En

English

7 VOLUME +/–

Increases or decreases the sound output level.

8 MUTE

Reduces the current volume level by approximately

20 dB. Press again to restore the audio output to the

previous volume level. Pressing the VOLUME +/–

also cancels muting.

The input indicator on the front panel for the current

input source blinks while the output is muted.

9 PURE DIRECT

Reproduces any input source in the purest sound

possible (see page 12).

0 Yamaha tuner control buttons

The following buttons can be used to control various

functions of a Yamaha tuner.

Refer to your component’s owner’s manual for more

information.

BAND

Selects the reception band (FM/AM).

TUNING jj / ii

Selects the tuning frequency.

MEMORY

Stores the current FM/AM station as a preset.

PRESET j / i

Selects a preset FM/AM station.

Even when using a Yamaha tuner, certain components and

features may not be available.

A Yamaha CD player control buttons

The following buttons can be used to control a

Yamaha CD player.

Refer to your component’s owner’s manual for more

information.

w Rewinds playback

f Fast-forwards playback

DISC SKIP Skips to the next disc in a CD changer

(A-S501/S301 only)

e Pauses playback

b Skips backward

a Skips forward

p Starts playback

s Stops playback

Even when using a Yamaha CD player, certain components

and features may not be available.

Note

CONTROLS AND FUNCTIONS

8 En

■ Installing batteries ■ Operation range

Point the remote control at the remote control sensor on

this unit and remain within the operating range shown

below.

■ Notes on remote control and batteries

• The area between the remote control and this unit must be clear of large obstacles.

• Be careful not to spill water or other liquids on the remote control.

• Be careful not to drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bathroom

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a

different specification.

• Dispose of batteries according to your regional regulations.

• Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or her mouth.

• If you plan not to use this unit for a long period of time, remove the batteries from this unit. Otherwise, the batteries will wear out,

possibly resulting in a leakage of battery liquid that may damage this unit.

AA, R6, UM-3 batteries

Approximately

6 m

Remote control

9 En

English

Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will

be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and

lack bass. Refer to the owner’s manual for each of your components.

Make sure to use RCA cables or optical cable to connect audio components.

Do not connect this unit or other components to the main power until all connections between components are complete.

Only PCM signals can be input to the DIGITAL (OPTICAL/COAXIAL) jacks of this unit. For details on the supported

PCM signals, see page 15.

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

CONNECTIONS

Connecting speakers and source components

CAUTION

CD recorder,

etc.

Tuner

Speakers A

Speakers B

DVD player,

etc.

CD player

Turntable

Audio

out

Audio

out

Audio

out

GND

LeftRight

Audio

out

Audio

out

TV, etc.

Audio

out

SubwooferTape deck,

etc.

BD player, etc.

Audio

out

Audio

out

Audio

10 En

CONNECTIONS

■ REC jacks

• The audio signals are not output via the LINE 2 REC

or LINE 3 REC output jacks when LINE 2 or LINE 3

is selected with the INPUT selector.

• The VOLUME, BASS, TREBLE, BALANCE and

LOUDNESS controls and the CD DIRECT function

(or the PURE DIRECT function) have no effect on the

source being recorded.

■ Connecting speaker cables

1 Remove approximately 10 mm of insulation from the

end of each speaker cable.

2 Twist the bare wires of the cable firmly together.

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side of each

terminal.

5 Tighten the knob to secure the wire.

• Set the IMPEDANCE SELECTOR switch according to

the impedance of the speakers to be connected (see

page 5).

• Do not let bare speaker wires touch each other or any

metal part of this unit. This could damage this unit and/

or the speakers.

■ Connecting via banana plug

(North America, General, China and

Australia models only)

1 Tighten the knob.

2 Insert the banana plug into the end of the

corresponding terminal.

■ Bi-wire connection

In the case of speakers supporting the bi-wiring

connection, the tweeter/midrange unit and woofer of the

speakers can be driven independently through connections

shown in the following figure, allowing you to enjoy clear

mid- and high-range sounds.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker. Refer to the speakers’ instruction

manuals for more information.

To use the bi-wire connections, set the SPEAKERS selector on

the front panel to the A+B BI-WIRING position.

(General model only)

Before connecting the power cable, make sure you set

VOLTAGE SELECTOR of this unit according to your

local voltage. Improper setting of VOLTAGE SELECTOR

may cause fire and damage to this unit.

■ AC IN (A-S701)

Connect the supplied power cable to AC IN after all other

connections are complete.

■ Power cable (A-S501/S301)

Connect the power cable to an AC wall outlet after all

other connections are complete.

CAUTION

Red: positive (+)

Black: negative (–)

10 mm

Banana plug

Note

Connecting power cable

CAUTION

Rear panel

Speaker

To the AC

wall outlet

(A-S701)

To the AC

wall outlet

(A-S501/S301)

11 En

English

1 Rotate the VOLUME control on the front

panel fully counter-clockwise so as not to

play sounds loud suddenly.

2 Press A (power) switch on the front panel

inward to turn on this unit.

3 Rotate the INPUT selector on the front panel

(or press one of the Input selector buttons on

the remote control) to select the input source

you want to listen to.

The indicator for the selected input source lights up.

4 Rotate the SPEAKERS selector on the front

panel to select SPEAKERS A, B or A+B BI-

WIRING.

Set the SPEAKERS selector to the A+B BI-WIRING position

when two sets of speakers are connected using bi-wire

connections, or when using two sets of speakers simultaneously

(A and B).

5 Play the selected input source.

6 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to adjust the sound output level.

You can adjust to the desired sound by using the BASS,

TREBLE, BALANCE and LOUDNESS controls, the CD

DIRECT AMP button, or the PURE DIRECT button on the front

panel.

7 When finished listening, press A (power)

switch on the front panel outward to turn off

this unit.

If A AMP on the remote control is pressed while the A (power)

switch on the front panel is in the on position, this unit enters

standby mode. Press A AMP again to turn this unit on.

PLAYBACK

Playing a source

SPEAKERS VOLUME

INPUTA

Input selector

buttons

VOLUME +/–

A AMP

(A-S701)

12 En

PLAYBACK

■ Making it easier to hear the high- and

low-frequency ranges even at low

volume (LOUDNESS)

Enjoy natural sound even at low volume by lowering the

mid-range sound level and compensating for the human

ears’ loss of sensitivity to high- and low-frequency ranges

at low volume.

If the CD DIRECT AMP function (or the PURE DIRECT

function) is turned on with the LOUDNESS control set at

a certain level, the input signals bypass the loudness

control, resulting in a sudden increase in the sound output

level. To prevent your ears or the speakers from being

damaged, be sure to press the CD DIRECT AMP button

(or the PURE DIRECT button) AFTER lowering the

sound output level or AFTER checking that the

LOUDNESS control is properly set.

1 Set the LOUDNESS control to the FLAT

position.

2 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to set the sound output level to the

loudest listening level that you would listen

to.

3 Rotate the LOUDNESS control

counterclockwise until the desired volume is

obtained.

■ Reproducing pure, high fidelity sound

(PURE DIRECT)

When the PURE DIRECT function is on, noise can be

reduced by bypassing the circuit that the audio input

signal is not using and stopping the power supply to the

circuit.

Therefore, in all input sources, you can enjoy music

playback in straight and high quality sound.

The indicator above the PURE DIRECT button lights up

when this function is turned on.

The BASS, TREBLE, BALANCE and LOUDNESS controls do

not function while the PURE DIRECT function is turned on.

■ Reproducing CD sound with the highest

sound quality (CD DIRECT AMP)

(A-S701 only)

When selecting the input source other than CD, if you

press the CD DIRECT AMP button, the input source

switches to CD.

• The BASS, TREBLE, BALANCE and LOUDNESS controls do

not function while the CD DIRECT AMP function is turned on.

• Be sure to connect the CD player to the CD input jacks if you

use the CD direct function.

• The CD DIRECT AMP function is turned off if the following

operation is performed.

– Select an input source other than CD for the INPUT selector.

– The PURE DIRECT function is turned on.

Adjusting to the desired sound

CAUTION

VOLUMELOUDNESS

PURE

DIRECT

CD DIRECT

AMP

(A-S701)

Note

CD Direct Amp feature

Stop power supply to the unnecessary circuit for CD

playback, convert the input signal to the normal phase

and reverse phase, and balance transfer to the electronic

volume. With the following effects, a more faithful

sound to the original will be provided.

• improved signal-to-noise ratio

• external noise canceling

• reduced distortion

Notes

13 En

English

Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or

if the instructions below do not help, turn off this unit, disconnect the power cable, and then contact the nearest

authorized Yamaha dealer or service center.

TROUBLESHOOTING

Problem Cause Remedy

See

page

This unit fails to turn

on.

The power cable is not connected or the

plug is not completely inserted.

Connect the power cable firmly.

The A AMP is pressed on the remote

control while this unit is turned off.

Press A (power) switch on the front panel to on.

The impedance setting of the connected

speaker is too small.

Use speaker(s) with proper speaker impedance.

The protection circuitry has been activated

because of a short circuit, etc.

Check that the speaker wires are not touching each

other and then turn the power of this unit back on.

There is a problem with the internal

circuitries of this unit.

Disconnect the power cable and contact the nearest

authorized Yamaha dealer or service center.

—

This unit turns off

suddenly and the

power indicator

blinks.

The speaker wires are touching each other

or shorting out against the rear panel.

Connect the speaker cables properly and press the A

(power) switch again. The INPUT indicators blink

and the volume is decreased to the lowest setting

automatically, then the INPUT indicators stop

flashing and the last input source selected lights up.

Confirm normal sound output from speakers by

increasing the volume gradually.

The speaker is malfunctioning. Replace the speaker set and press the A (power)

switch again. The INPUT indicators blink and the

volume is decreased to the lowest setting

automatically, then the INPUT indicators stop

flashing and the last input source selected lights up.

Confirm normal sound from speakers by increasing

the volume gradually.

—

The protection circuitry has been activated

because of excessive input or excessive

volume level.

Rotate the VOLUME control on the front panel to

decrease the volume level and then turn the power on

again.

—

The protection circuitry has been activated

due to excessive internal temperature.

Allow about 30 minutes for the temperature inside

this unit to decrease, rotate the VOLUME control on

the front panel to lower the volume and then turn the

power on again. Set the unit in a place where heat can

readily dissipate from the unit.

—

The IMPEDANCE SELECTOR switch is

not fully slid to either position.

Turn the power off and slide the IMPEDANCE

SELECTOR switch all the way to the correct position.

The IMPEDANCE SELECTOR switch is

not set to the correct position.

Set the IMPEDANCE SELECTOR switch to the

position that corresponds to the impedance of your

speakers.

This unit has been exposed to a strong

external electric shock (such as lightning

or strong static electricity).

Turn off this unit, disconnect the power cable, plug it

back in after 30 seconds, then use the unit normally.

—

There is a problem with the internal

circuitries of this unit.

Disconnect the power cable and contact the nearest

authorized Yamaha dealer or service center.

—

No sound. Sound is muted. Press MUTE on the remote control or rotate the

VOLUME control.

Incorrect cable connections. Connect the stereo cable for audio units and the

speaker wires properly. If the problem persists, the

cables may be defective.

14 En

TROUBLESHOOTING

No sound. Playback has been stopped on the

connected component.

Turn the component on and start playback.

No appropriate input source has been

selected.

Select an appropriate input source with the INPUT

selector on the front panel (or one of the Input

selector buttons on the remote control).

The SPEAKERS selector is not set

properly.

Set the corresponding SPEAKERS selector to A, B or

A+B BI-WIRING position.

The output audio source setting on the

connected component is not PCM.

Only PCM audio sources can be played via the

DIGITAL (OPTICAL/COAXIAL) jacks of this unit.

Set the output audio source of the connected

component to PCM.

The sound suddenly

goes off.

The automatic power down function has

activated.

Confirm that there are no other issues causing this

problem, and then turn this unit on again.

To turn off the AUTO POWER STANDBY function,

set the AUTO POWER STANDBY switch to OFF on

the rear panel.

Only the speaker on

one side can be

heard.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

Incorrect setting for the BALANCE

control.

Set the BALANCE control to the appropriate

position.

There is a lack of bass

and no ambience.

The + and – wires are connected in

reverse at the amplifier or the speakers.

Connect the speaker wires to the correct + and –

phase.

A “humming” sound

can be heard.

Incorrect cable connections. Connect the audio plugs firmly. If the problem

persists, the cables may be defective.

9, 10

No connection from the turntable to the

GND terminal.

Make the GND connection between the turntable and

this unit.

The volume level

cannot be increased,

or the sound is

distorted.

The component connected to the LINE 2

REC or LINE 3 REC jacks of this unit is

turned off.

Turn on the power of the component.

—

The sound is

degraded when

listening with

headphones

connected to a CD

player connected to

this unit.

This unit is turned off or is in standby

mode.

Turn on the power of this unit.

—

The sound level is

low.

Sound is muted. Press MUTE on the remote control or rotate the

VOLUME control.

The loudness control function is

operating.

Turn down the volume, set the LOUDNESS control

to the FLAT position, and then adjust the volume

again.

The volume level is

low while playing a

record.

The turntable is connected to the jacks

other than the PHONO jacks.

Connect the turntable to the PHONO jacks.

The record is being played on a turntable

with an MC cartridge.

Use a turntable equipped with an MM cartridge.

Using the BASS,

TREBLE, BALANCE

and LOUDNESS

controls does not

affect the sound.

The CD DIRECT function or the PURE

DIRECT function is turned on.

The CD DIRECT function or the PURE DIRECT

function must be turned off to use those controls.

Problem Cause Remedy

See

page

15 En

English

AUDIO SECTION

SPECIFICATIONS

Item A-S701 A-S501 A-S301

Minimum RMS output power

8 Ω, 20 Hz to 20 kHz, 0.019% THD 100 W + 100 W 85 W + 85 W 60 W + 60 W

6 Ω, 20 Hz to 20 kHz, 0.038% THD

(Except for Asia and China models)

120 W + 120 W 100 W + 100 W 70 W + 70 W

Dynamic power per channel (IHF)

8 Ω 140 W 130 W 100 W

6 Ω 170 W 150 W 120 W

4 Ω 220 W 185 W 140 W

2 Ω 290 W 220 W 150 W

Maximum power per channel

1 kHz, 0.7% THD, 4 Ω

(U.K. and Europe models only)

160 W 120 W 95 W

IEC power

1 kHz, 0.019% THD, 8 Ω

(U.K. and Europe models only)

115 W 100 W 75 w

Power band width

0.04% THD, 50 W, 8 Ω 10 Hz to 50 kHz — —

0.04% THD, 42.5 W, 8 Ω — 10 Hz to 50 kHz —

0.04% THD, 30 W, 8 Ω — — 10 Hz to 50 kHz

Damping factor (SPEAKERS A) 1 kHz, 8 Ω 240 or more 210 or more

Maximum Effective Output Power

(JEITA)

1 kHz, 10% THD, 8 Ω

(Asia, China and General models

only)

145 W 130 W 100 W

1 kHz, 10% THD, 6 Ω

(General model only)

170 W — —

Input sensitivity/Input impedance

PHONO (MM) 3.0 mV/47 kΩ

CD, etc. 200 mV/47 kΩ

Maximum input signal

PHONO (MM) (1 kHz, 0. 03%

THD)

45 mV or more

CD etc. (1 kHz, 0.5% THD) 2.2 V or more

Output level/Output impedance

REC OUT 200 mV/1.0 kΩ or less

SUBWOOFER OUT (Cut Off

Frequency: 100 Hz)

3.5 V/1.2 kΩ

PHONES jack rated output/

Impedance

CD, etc. (Input 1 kHz, 200 mV,

8 Ω)

470 mV/470 Ω 430 mV/470 Ω 360 mV/470 Ω

Frequency response

CD, etc. (20 Hz to 20 kHz) 0 ± 0.5 dB

CD, etc. PURE DIRECT on (10 Hz

to 100 kHz)

0 ± 1.0 dB

RIAA equalization deviation PHONO (MM) ± 0.5 dB

Total harmonic distortion

PHONO (MM) to REC OUT (20

Hz to 20 kHz, 2.5 V)

0.03 % or less

CD, etc. to SPEAKERS (20 Hz to

20 kHz, 50 W, 8 Ω)

0.019 % or less — —

CD, etc. to SPEAKERS (20 Hz to

20 kHz, 45 W, 8 Ω)

— 0.019 % or less —

CD, etc. to SPEAKERS (20 Hz to

20 kHz, 30 W, 8 Ω)

— — 0.019 % or less

16 En

SPECIFICATIONS

GENERAL

Specifications are subject to change without notice.

Signal to noise ratio (IHF-A

network)

PHONO (MM)

(5 mV input shorted)

82 dB or more

CD, etc. PURE DIRECT on

(200 mV input shorted)

99 dB or more

CD DIRECT AMP on 104 dB or more — —

Residual noise (IHF-A network) 40 μV

Channel separation

CD, etc. (5.1 kΩ input shorted,

1kHz)

65 dB or more

CD, etc. (5.1 kΩ input shorted,

10 kHz)

50 dB or more

Tone control characteristics

BASS

Boost/

Cut (20 Hz)

± 10 dB

Turnover

frequency

400 Hz

TREBLE

Boost/

Cut (20 kHz)

± 10 dB

Turnover

frequency

3.5 kHz

Continuous loudness control Attenuation (1 kHz) – 30 dB

Supported digital audio format

(OPTICAL/COAXIAL)

PCM (2-ch) 192/176.4/96/88.2/48/44.1/32 kHz

PCM word depth 24 bit/16 bit

Item A-S701 A-S501 A-S301

Power supply

U.S.A. and Canada models AC 120 V, 60 Hz

Asia model AC 220-240 V, 50/60 Hz

General model AC 110-120 V/220-240 V, 50/60 Hz

China model — AC 220 V, 50 Hz

Korea model — — AC 220 V, 60 Hz

Australia model AC 240 V, 50 Hz

U.K. and Europe models AC 230 V, 50 Hz

Power consumption

U.S.A and Canada, General,

Australia, U.K and Europe models

270 W 240 W 190 W

Asia model 230 W 220 W 170 W

China model — 220 W 170 W

Korea model — — 190 W

Standby power consumption 0.5 W

Maximum power consumption

1 kHz 6 Ω 10% THD

(General model only)

580 W 510 W 430 W

Dimensions W × H × D 435 × 151 × 387 mm (17-1/8" × 6" × 15-1/4")

Weight 11.2 kg (24.7 lbs) 10.3 kg (22.7 lbs) 9.0 kg (19.8 lbs)

17 En

SPECIFICATIONS

English

Information for Users on Collection and Disposal of Old Equipment

and Used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC

and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent

any potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER L’APPAREIL.

i Fr

1 Pour utiliser l’appareil au mieux de ses possibilités, lisez

attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

2 Installez cet ensemble audio dans un endroit bien aéré,

frais, sec et propre - veillez à ce qu’il soit à l’abri de la

lumière directe du soleil, des sources de chaleur, des

vibrations, des poussières, de l’humidité et/ou du froid.

Pour une ventilation correcte, ménagez l’espace

minimum suivant autour de cet appareil.

Au-dessus : 30 cm

À l’arrière : 20 cm

Sur les côtés : 20 cm

3 Placez l’appareil loin des équipements, moteurs et

transformateurs électriques, pour éviter les ronflements

parasites.

4 N’exposez pas l’appareil à des variations brutales de

température, ne le placez pas dans un environnement très

humide (par exemple dans une pièce contenant un

humidificateur) car cela peut entraîner la condensation

d’humidité à l’intérieur de l’appareil qui elle-même peut

être responsable de décharge électrique, d’incendie, de

dommage à l’appareil ou de blessure corporelle.

5 Evitez d’installer l’appareil dans un endroit où des objets

peuvent tomber, ainsi que là où l’appareil pourrait être

exposé à des éclaboussures ou des gouttes d’eau. Sur le

dessus de l’appareil, ne placez pas :

– d’autres appareils qui peuvent endommager la surface

de l’appareil ou provoquer sa décoloration.

– des objets se consumant (par exemple, une bougie)

qui peuvent être responsables d’incendie, de

dommage à l’appareil ou de blessure corporelle.

– des récipients contenant des liquides qui peuvent être

à l’origine de décharge électrique ou de dommage à

l’appareil.

6 Ne couvrez pas l’appareil d’un journal, d’une nappe, d’un

rideau, etc. car cela empêcherait l’évacuation de la

chaleur. Toute augmentation de la température intérieure

de l’appareil peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle.

7 Ne branchez pas la fiche du câble d’alimentation de

l’appareil sur une prise secteur aussi longtemps que tous

les raccordements n’ont pas été effectués.

8 Ne pas faire fonctionner l’appareil à l’envers. Il risquerait

de chauffer et d’être endommagé.

9 N’exercez aucune force excessive sur les commutateurs,

les boutons et les cordons.

10 Pour débrancher la fiche du câble d’alimentation au

niveau de la prise secteur, saisissez la fiche et ne tirez pas

sur le cordon.

11 Ne nettoyez pas l’appareil au moyen d’un solvant

chimique, ce qui pourrait endommager la finition.

Utilisez un chiffon sec et propre.

12 N’alimentez l’appareil qu’à partir de la tension prescrite.

Alimenter l’appareil sous une tension plus élevée est

dangereux et peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle. Yamaha

ne saurait être tenue responsable des dommages résultant

de l’alimentation de l’appareil sous une tension autre que

celle prescrite.

13 Pour empêcher tout dommage causé par les éclairs,

déconnectez le câble d’alimentation et toute antenne

extérieure de la prise murale pendant un orage.

14 Ne tentez pas de modifier ni de réparer l’appareil.

Consultez le service Yamaha compétent pour toute

réparation qui serait requise. Le coffret de l’appareil ne

doit jamais être ouvert, quelle que soit la raison.

15 Si vous envisagez de ne pas vous servir de l’appareil

pendant une longue période (par exemple, pendant les

vacances), débranchez la fiche du câble d’alimentation au

niveau de la prise secteur.

16 Lisez la section intitulée « GUIDE DE DÉPANNAGE »

où figurent une liste d’erreurs de manipulation

communes avant de conclure que l’appareil présente une

anomalie de fonctionnement.

17 Avant de déplacer l’appareil, appuyez sur

A (alimentation) pour mettre l’appareil en mode veille,

puis débranchez la fiche du cordon d’alimentation au

niveau de la prise secteur.

18 La condensation se forme lorsque la température

ambiante change brusquement. En ce cas, débranchez la

fiche du câble d’alimentation et laissez l’appareil reposer.

19 La température de l’appareil peut augmenter en raison

d’une utilisation prolongée. En ce cas, coupez

l’alimentation de l’appareil et laissez-le au repos pour

qu’il refroidisse.

20 Installez cet appareil à proximité de la prise secteur et à

un emplacement où la fiche du câble d’alimentation est

facilement accessible.

21 Les piles ne doivent pas être exposées à une chaleur

extrême, par exemple au soleil, à une flamme, etc.

22 Une pression excessive du son par les écouteurs et le

casque d’écoute peut entraîner la perte de l’ouïe.

Cette étiquette doit être apposée sur un produit dont le

capot supérieur peut devenir chaud lorsqu’il fonctionne.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER

L’APPAREIL.

Cet appareil n’est pas déconnecté du secteur tant qu’il reste

branché à la prise de courant, même si l’appareil en soi est éteint

par la touche A. Il se trouve alors « en veille ». En mode veille,

l’appareil consomme une très faible quantité de courant.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET

APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

Sayfa yükleniyor ...

Yamaha A-S301 Kullanım kılavuzu

Marka: Yamaha

Model: A-S301

Kategori: Ses amplifikatörleri

Tip: Kullanım kılavuzu

PDF İndir

rapor

Diğer dillerde

español: Yamaha A-S301 Manual de usuario
français: Yamaha A-S301 Manuel utilisateur
italiano: Yamaha A-S301 Manuale utente
svenska: Yamaha A-S301 Användarmanual
Deutsch: Yamaha A-S301 Benutzerhandbuch
English: Yamaha A-S301 User manual
dansk: Yamaha A-S301 Brugermanual
русский: Yamaha A-S301 Руководство пользователя
suomi: Yamaha A-S301 Ohjekirja
Nederlands: Yamaha A-S301 Handleiding

Yamaha A-S301 Kullanım kılavuzu

Yamaha A-S301 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler