Yamaha NS-P230 El kitabı

NS-P230/

NS-P236

(NS-P230/NS-P236: NX-230P + NX-C230 + YST-SW005)

HOME CINEMA 5.1CH SPEAKER PACKAGE/

HOME CINEMA 6.1CH SPEAKER PACKAGE

5.1 SYSTEM D’ENCEINTES HOME CINEMA/

6.1 SYSTEM D’ENCEINTES HOME CINEMA

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

NS-P230-236 PRE(02.5.8)a 02.5.8, 9:58 PM1

● Subwoofer cable

● Câble pour subwoofer

● Subwoofer-Kabel

● Subwooferkabel

● Cavo per subwoofer

● Cable del subwoofer

● Subwooferkabel

● Mounting brackets

● Supports de montage

● Befestigungshalterungen

● Monteringsfästen

● Staffe di montaggio

● Ménsulas de instalación

● Montagesteunen

● Fasteners (for NX-C230)

● Fixations (pour NX-C230)

● Befestigung (für NX-C230)

● Fästanordning (för NX-C230)

● Fermi (per l’NX-C230)

● Sujetadores (para NX-C230)

● Bevestiging (voor NX-C230)

● Nonskid pads (for NX-230P)

● Patins anti-dérapages (pour NX-230P)

● Gleitschutzpads (für NX-230P)

● Glidskyddsdynor (för NX-230P)

● Cuscinetti antiscivoli (per l’NX-230P)

● Almohadillas antideslizantes (para NX-230P)

● Antislipplaatjes (voor NX-230P)

● Nonskid pads (for YST-SW005)

● Patins anti-dérapages (pour YST-SW005)

● Gleitschutzpads (für YST-SW005)

● Glidskyddsdynor (för YST-SW005)

● Piedini antisdrucciolevoli (per l’YST-SW005)

● Almohadillas antideslizantes (para YST-SW005)

● Antislipplaatjes (voor YST-SW005)

● Screws

● Vis

● Schrauben

● Skruvar

● Viti

● Tornillos

● Schroeven

● Main and rear speakers

(and rear center speaker for NS-P236)

● Enceintes principales et arrière

(

et enceinte arrière centrale pour le NS-P236

)

● Haupt- und hinteres Lautsprecherpaar

(

und hinteren Centerlautsprecher für NS-P236

)

● Huvudhögtalare och bakre högtalare

(samt bakre mitthögtalare för NS-P236)

● Altoparlanti principali e posteriori

(

e altoparlante posteriore centrale del modello NS-P236

)

● Altavoces principales y traseros

(

y altavoz central trasero para NS-P236

)

● Hoofdluidsprekers en achterluidsprekers

(

en als achter-middenluidspreker voor NS-P236

)

● Center speaker

● Enceinte centrale

● Centerlautsprecher

● Mitthögtalare

● Altoparlante centrale

● Altavoz central

● Middenluidspreker

● Subwoofer

● Subwooferhögtalaren

● Subwoofer

● Altavoz ultragraves

● Subwoofer

● Speaker cables

● Câbles d’enceintes

● Lautsprecheranschlußkabel

● Högtalarledningar

● Cavi per gli altoparlanti

● Cables de los altavoces

● Luidsprekerdraden

UNPACKING After unpacking, check that the following items are contained.

DEBALLAGE Après le déballage, vérifier que les pièces suivantes sont incluses.

AUSPACKEN Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.

UPPACKNING Kontrollera efter det apparaten packats upp att följande delar finns med.

DISIMBALLAGGIO Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.

DESEMBALAJE Desembale el aparato y verifique que los siguientes accesorios están en la caja.

UITPAKKEN Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.

[4m]

[15m]

X 2

X 3

NX-230P

NX-C230

YST-SW005

X 2

<NS-P230>

X 3

<NS-P236>

X 4

<NS-P230>

X 5

<NS-P236>

X 4

<NS-P230>

X 5

<NS-P236>

X 4

<NS-P230>

X 5

<NS-P236>

SUBWOOFER SYSTEM YST SW005SUPERWOOFER SYSTEM YST-SW005

X 2

<NS-P230>

X 3

<NS-P236>

NS-P230-236 PRE(02.5.8)a 02.5.8, 9:59 PM2

English

E-1

●

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

●

Install the speakers in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration, dust,

moisture and cold. Avoid sources of humming (transformers,

motors). To prevent fire or electric shock, do not expose the

speakers to rain or water.

●

To prevent the enclosure from warping or discoloring, do not

place the speakers where they will be exposed to direct sunlight

or excessive humidity.

●

Avoid installing the speakers where foreign objects may fall onto

them and/or where they may be exposed to liquid dripping or

splashing.

Do not place the following objects on top of the speakers:

●

Other components, as they might cause damage and/or

discoloration on the surface of the speakers.

●

Burning objects (i.e. candles), as they might cause fire,

damage to the speakers and/or personal injury.

●

Containers with liquid in them, as they might cause electric

shock to the user and/or damage to the speakers.

●

Do not place the speakers where they are liable to be knocked

over or struck by falling objects. Stable placement will also

ensure better sound performance.

●

Placing the speakers on the same shelf or rack as the turntable

can result in feedback.

●

Secure placement or installation is the owner’s responsibility.

YAMAHA shall not be liable for any accident caused by improper

placement or installation of speakers.

●

Any time you note distortion, reduce the volume control on your

amplifier to a lower setting. Never allow your amplifier to be

driven into “clipping”. Otherwise the speakers may be damaged.

●

When using an amplifier with a rated output power higher than

the nominal input power of the speakers, care should be taken

never to exceed the speakers’ maximum input.

●

Do not attempt to clean the speakers with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

●

Do not attempt to modify or fix the speakers. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

●

Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the speakers

are faulty.

For YST-SW005

●

Do not operate this unit upside down. It may overheat, possibly

causing damage.

●

Do not use excessive force on switches, controls or connection

wires. When moving this unit, first disconnect the power plug

and the wires connected to other equipments. Never pull the

wires themselves.

●

Since this unit has a built-in power amplifier, heat will radiate

from the rear panel. Place the unit apart from the walls, allowing

enough spaces above, behind and on both sides of the unit to

prevent fire or damage. Furthermore, do not position with the

rear panel facing down on the floor or other surfaces.

Be sure to allow spaces of at least 20 cm above, behind and on

both sides of the unit.

●

When using a humidifier, be sure to avoid condensation inside

this unit by allowing enough spaces around this unit or avoiding

excess humidification. Condensation might cause a fire, damage

to this unit, and/or electric shock.

CAUTION: Read this before operating your unit.

Thank you for selecting this YAMAHA NS-P230/NS-P236 Speaker Package.

●

Do not cover the rear panel of this unit with a newspaper, a

tablecloth, a curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause fire, damage

to this unit and/or personal injury.

●

Do not plug in this unit to a wall outlet until all connections are

completed.

●

The voltage to be used must be the same as that specified on

the rear panel. Using this unit with a higher voltage than

specified is dangerous and may cause fire, damage to this unit,

and/or personal injury. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a voltage other

than specified.

●

To prevent lightning damage, disconnect the AC power plug

when there is an electric storm.

●

Super-bass frequencies reproduced by this unit may cause a

turntable to generate a howling sound. In such a case, move this

unit away from the turntable.

●

This unit may be damaged if certain sounds are continuously

outputted at high volume level. For example, if 20 Hz–50 Hz sine

waves from a test disc, bass sounds from electronic instruments,

etc. are continuously outputted, or when the stylus of a turntable

touches the surface of a disc, reduce the volume level to prevent

this unit from being damaged.

●

If you hear distorted noise (i.e. unnatural, intermittent “rapping” or

“hammering” sounds) coming from this unit, reduce the volume

level. Extremely loud playing of a movie soundtrack’s low

frequency, bass-heavy sounds or similarly loud popular music

passages can damage this speaker system.

●

Vibration generated by super-bass frequencies may distort

images on a TV. In such a case, move this unit away from the TV

set.

●

When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

●

When not planning to use this unit for a long period (i.e. vacation,

etc.), disconnect the AC power plug from the wall outlet.

●

VOLTAGE SELECTOR

(For China, Korean and General models)

The voltage selector switch on

the rear panel of this unit must

be set for your local main

voltage BEFORE plugging this

unit into the AC main supply.

Voltages are 110-120/220-240 V AC,

50/60 Hz.

Standby mode

If the POWER switch is set to the ON position and the AUTO

STANDBY switch is set to the HIGH or LOW position, this unit

turns into the standby mode when no signal is received by this

unit for 7 to 8 minutes.

In this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

110V-120V

VOLTAGE

SELECTOR

220V-240V

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM1

E-2

CONTENTS

UNPACKING .................... Inside of Front Cover

CAUTION .........................................................1

COMPONENTS OF THE PACKAGE .............. 2

SETTING UP THE SPEAKERS ...................... 3

Placing the subwoofer ................................... 4

Placing the center speaker ............................. 4

Mounting the rear speakers (and rear center

speaker for NS-P236) .................................... 5

Placing the main/rear speakers (and rear center

speaker for NS-P236)

.................................... 6

CONNECTIONS.............................................. 7

An example of basic connections .................... 7

How to connect speaker cables to the input

and output terminals of the speakers

............... 9

Connecting the subwoofer to speaker output

terminals of the amplifier .............................. 10

USING THE SUBWOOFER (YST-SW005) ... 11

Controls and their functions .......................... 11

Adjusting the subwoofer before use ................ 12

Frequency characteristics ................................ 13

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY (for YST-SW005) ................ 14

TROUBLESHOOTING .................................. 15

SPECIFICATIONS ........................................ 16

COMPONENTS OF THE PACKAGE

<NX-230P>

Full range acoustic-suspension speaker system used

for the main and rear speakers (and rear center speaker

for NS-P236)

<NX-C230>

Full range acoustic-suspension speaker system used

for the center speaker

<YST-SW005>

Active Servo Processing Subwoofer System with a

built-in power amplifier

● This subwoofer system employs Advanced YAMAHA

Active Servo Technology which YAMAHA has developed

for reproducing higher quality super-bass sound. (Refer to

page 14 for details on Advanced YAMAHA Active Servo

Technology.) This super-bass sound adds a more

realistic, theater-in-the-home effect to your stereo system.

● This subwoofer can be easily added to your existing

audio system by connecting to either the speaker

terminals or the line output (pin jack) terminals of the

amplifier.

● The AUTO STANDBY switch saves you the trouble of

setting the POWER switch to the ON or OFF position.

The speaker package “NS-P230 and NS-P236” is designed

for use in a multi-channel audio system such as a home

theater system.

NS-P230 includes four NX-230P speaker systems, one NX-

C230 speaker system and one YST-SW005 subwoofer

system.

NS-P236 includes five NX-230P speaker systems, one NX-

C230 speaker system and one YST-SW005 subwoofer

system.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM2

English

E-3

SETTING UP THE SPEAKERS

Before making connections, place all speakers in their respective positions. The positioning of the speakers is important

because it controls the whole sound quality of this system.

Place the speakers depending on your listening position by following the instructions below.

Speaker configuration

<NS-P230>

This speaker package employs a 6 speaker configuration: 2

main speakers, 2 rear speakers, a center speaker and a

subwoofer.

The main speakers emit main source sound. The rear

speakers emit surround sounds, and the center speaker

emits center sounds (dialog etc.). The subwoofer emits

reinforcing low frequencies on your audio system.

<NS-P236>

This speaker package employs a 7 speaker configuration: 2

main speakers, 2 rear speakers, a center speaker, a rear

center speaker and a subwoofer.

The main speakers emit main source sound. The rear and

rear center speakers emit surround sounds, and the center

speaker emits center sounds (dialog etc.). The subwoofer

emits reinforcing low frequencies on your audio system.

Note

In this speaker package, the same speakers (NX-230P)

are used for the main and rear speakers (and rear

center speaker for NS-P236).

Placing speakers

Main speakers: On both sides of and at approximately

the same height as the TV set.

Rear speakers: Behind your listening position, facing

slightly inward. About 1.8 m (approx. 6

feet) from the floor.

Center speaker: Precisely between the main speakers.

Rear center speaker (for NS-P236):

Precisely between the rear speakers.

Subwoofer: The position of the subwoofer is not so

critical because low bass tones are not

highly directional.

Refer to “Placing the subwoofer” below

for a recommended positioning of the

subwoofer.

Main L Center Main R

Rear L

Subwoofer

Rear R

Main L

Main R

Subwoofer

Center

Rear L

Rear R

TV-set

Rear center

(for NS-P236)

Rear center

(for NS-P236)

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM3

E-4

 Placing the subwoofer

It is recommended to place the subwoofer on the outside of

either the right or the left main speaker. (See fig. Å .) The

placement shown in fig. ı is also possible, however, if the

subwoofer system is placed directly facing the wall, the

bass effect may die because the sound from it and the

sound reflected by the wall may cancel out each other. To

prevent this from happening, face the subwoofer system at

an angle as shown in fig. Å.

Note

There may be a case that you cannot obtain enough super-

bass sounds from the subwoofer when listening in the

center of the room. This is because “standing waves” have

been developed between two parallel walls and they cancel

the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It

also may be necessary to break up the parallel surfaces by

placing bookshelves etc. along the walls.

Use the nonskid pads

Put the provided nonskid pads at the four corners on the

bottom of the subwoofer to prevent the subwoofer from

moving by vibrations etc.

( : Subwoofer, : Main speaker)

ıÅ

You can place the speaker on top of the TV if the top is flat,

on the floor under the TV, or inside the TV rack . Be sure to

place the speaker in a stable position.

When placing the speaker on top of the TV, to prevent the

speaker from falling, attach the provided fasteners at two

points on the bottom of the speaker and on the top of the

TV.

 Placing the center speaker

Notes

● Do not place the speaker on top of a TV whose area

is smaller than the bottom of the speaker. If placed,

the speaker may fall and cause injury.

● Do not place the speaker on top of a TV if the top is

inclined.

● Do not touch the adhesive surface after peeling off

the seal as this will weaken its adhesive strength.

● Thoroughly wipe clean the surface where the

fastener is to be applied. Note that adhesive strength

is weakened if the surface is dirty, oily or wet and

that this may cause the center speaker to fall.

Screen

Peel off

the seal

Fastener

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM4

English

E-5

 Mounting the rear speakers (and rear center speaker for

NS-P236)

Mount the rear speakers (and rear center speaker for NS-

P236) on a shelf, rack or directly on the floor, or hang them

on the wall.

To mount the speakers on a wall by

using the holes on the speakers’ back

panels

1 Fasten screws into a firm wall or wall support as shown

in the figure.

2 Hang the speaker by mounting the holes on the

protruding screws.

* Make sure that the screws are securely affixed by the

narrow parts of the holes.

WARNING

● Each speaker weighs 0.9 kg (2 lbs.). Do not mount

them on thin plywood or a wall composed of a soft

surface material. If mounted, the screws may pull out

of the flimsy surface and the speakers may fall. This

may damage the speakers or cause personal injury.

● Do not affix the speakers to a wall using nails,

adhesives, or any other unstable hardware. Long-

term use and vibrations may cause the speakers to

fall.

● To avoid accidents resulting from tripping over loose

speaker cables, fix the cables to the wall.

● Select an appropriate position on the wall to mount

the speaker so that no one will injure his/her head or

face.

1

70 mm

Holes

2

Wall/ wall

support

Tapping screw

(Available at the

hardware store)

Min.

20 mm

Diam. 3.5 to 4 mm

10 mm

70 mm

Using the Yamaha Speaker Stand SPS-80 (option)

By using the Yamaha Speaker

Stand SPS-80, speakers can be

placed on the floor.

* The SPS-80 is not available in some areas.

SPS-80

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM5

E-6

If you want to mount a speaker on a commercially available speaker stand for the

main/rear speakers (and rear center speaker for NS-P236)

Mounting

bracket

Screw

60 mm

The provided mounting bracket with 1 pair of screw holes

(at an interval of 60 mm) can be used to mount the

speaker on a speaker stand.

* Those screw holes can be used with M4 screws only.

1 Attach the bracket to the bottom of the speaker by

using the provided screw so that the convex part of

the bracket fits in the grooved part on the bottom of

the speaker as shown on the left.

2 Mount the speaker on the speaker stand by using the

screw holes on the bracket.

Note

The mounting bracket is provided for each speaker.

■ Placing the the main/rear speakers (and rear center speaker for

NS-P236)

Nonskid pad

When placing the speakers on a flat surface, attach the

included nonskid pads to the corners on the bottom of the

speakers as shown on the left. This prevents the speakers

from sliding around.

* For NS-P236, the nonskid pads include four spare ones.

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM6

English

E-7

SPEAKERS

MAIN

OUTPUT

SUB

WOOFER

CENTER

REAR CENTER

L

R

L

R

L

R

A

–

+

–

+

–

+

–

+

B

REAR

(SURROUND)

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

OFF

POWER

ON

VOLUME

010

INPUT2

/MONO

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

CENTER CENTER

FRONT R

FRONT LFRONT L

REAR C

REAR R

REAR L

REAR R

CONNECTIONS

Caution: Plug in the subwoofer and other audio/video components after all connections are

completed.

 An example of basic connections

Subwoofer

Amplifier

To AC outlet

Center speaker

Rear speaker

Right

LeftRight

Main speakers

Rear center speaker

(for NS-P236)

Rear speaker

Left

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM7

E-8

● Connect the main, center and rear speakers (and rear

center speaker for NS-P236) to the speaker output

terminals of your amplifier with the provided speaker

cables.

* The provided speaker cables have labels marked

FRONT L, FRONT R, CENTER, REAR L, REAR R

(and REAR C for NS-P236). Connect each speaker

cord to the corresponding speaker by following the

figure on page 7.

* Connect each speaker making sure not to reverse the

polarity (+, –). If the speaker is connected with

reversed polarity, the sound will be unnatural and lack

bass.

* For the main and rear speakers only, connect one

speaker to the left (marked L) terminals of your

amplifier, and another speaker to the right (marked R)

terminals.

● Basically, connect the subwoofer to the line output (pin

jack) terminal(s) of the amplifier. If your amplifier does

not have any line output terminal, connect the subwoofer

to the speaker output terminals of the amplifier. (Refer to

page 9 for details.)

* To connect with a YAMAHA DSP amplifier (or AV

receiver), connect the SUBWOOFER (or LOW PASS

etc.) terminal on the rear of the DSP amplifier (or AV

receiver) to the L/MONO INPUT2 terminal of the

subwoofer.

* To connect the subwoofer to the SPLIT SUBWOOFER

terminals on the rear of the DSP amplifier, connect

them to both the left L and right R INPUT2 terminals

of the subwoofer.

Note

When connecting to a monaural line output terminal of the

amplifier, connect to the L/MONO INPUT2 terminal.

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM8

English

E-9

Main/center/rear speakers

Rear center speaker (for NS-P236)

One side of the provided speaker cable has a white broken

line and the other side has no line.

Connect the (+) terminals on both the speaker and the

amplifier using the side with a white broken line. Connect

the (–) terminals on both components using the side with no

line.

Red: positive (+)

Black: negative (–)

Subwoofer (INPUT1/OUTPUT terminals)

Connect the (+) terminals on both the subwoofer and the

amplifier using one side of the cable. Connect the (–)

terminals on both components using the other side of the

cable.

Red: positive (+)

Black: negative (–)

 How to connect speaker cables to the input and output terminals

of the speakers

For connections, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the

connections are faulty, no sound will be heard from the speakers.

Before connecting

Remove the insulation coating at the extremity of each

speaker cable by twisting the coating off.

How to Connect:

1 Press and hold the terminal’s tab, as shown in the

figure.

2 Insert the bare wire.

3 Release your finger from the tab to allow it to lock

securely on the cable’s wire end.

4 Test the firmness of the connection by pulling lightly on

the cable at the terminal.

Note

Do not let the bare speaker wires touch each other as

this could damage the speaker or the amplifier, or both

of them.

White broken line

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM9

E-10

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

OFF

POWER

ON

VOLUME

010

AB

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

FRONT R

FRONT L

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

OFF

POWER

ON

VOLUME

010

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

FRONT R

FRONT L

 Connecting the subwoofer to speaker output terminals of the

amplifier

If your amplifier has two sets of speaker output terminals

Left main

speaker

Right main

speaker

Subwoofer

Amplifier

Speaker

output

terminals

To AC outlet

If your amplifier has only one set of main speaker output terminals

Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT

terminals of the subwoofer to the main speakers.

(Both A and B speaker outputs

must be ON.)

Subwoofer

Amplifier

Speaker

output

terminals

To AC outlet

Left main

speaker

Right main

speaker

(Not included)

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM10

English

E-11

USING THE SUBWOOFER (YST-SW005)

 Controls and their functions

1 Power indicator

Lights up GREEN when the POWER switch (

2) is

pressed in to the ON position and goes off when set to

the OFF position.

* Standby mode

If the POWER switch (

2) is pressed in to the ON

position and the AUTO STANDBY switch (

4) is set

to the HIGH or LOW position, this indicator lights up

RED when no signal is received by the subwoofer.

2 POWER switch

Press this switch to the ON position to turn on the

power of the subwoofer. When the power of the

subwoofer is on, the power indicator (

1) on the front

panel lights up GREEN. Press this switch again to set

to the OFF position to turn off the power of the

subwoofer.

3 VOLTAGE SELECTOR switch

(For China, Korean and General models)

If the preset setting of the switch is incorrect, set the

switch to the proper voltage range (220V-240V or

110V-120V) of your area.

Consult your dealer if you are unsure of the correct

setting.

WARNING

Be sure to unplug the subwoofer before setting the

VOLTAGE SELECTOR switch correctly.

4 AUTO STANDBY (HIGH/LOW/OFF) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as explained on page 9. If you do not need

this function, set to the OFF position.

* Make sure to change the setting of this switch only

when the POWER switch (

2) is in the OFF position.

5 INPUT2 terminals

Used to input line level signals from the amplifier.

6 INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

7 OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the main speakers.

Signals from the INPUT1 terminals (

6) are sent to

these terminals.

8 VOLUME control

Adjusts the volume level. Turn the control clockwise to

increase the volume, and counterclockwise to

decrease the volume.

9 HIGH CUT (HIGH/LOW) switch

Selects the high frequency cut off point.

Normally, it is set to LOW, however, you may set to

HIGH if necessary. Refer to page 12–13.

SUBWOOFER SYSTEM YST SW005SUBWOOFER SYSTEM YST-SW005

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

OFF

POWER

ON

VOLUME

010

220V-240V

110V-120V

VOLTAGE

SELECTOR

6

7

5

9

4

8

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

VOLUME

010

OFF

POWER

ON

2

110V-120V

VOLTAGE

SELECTOR

220V-240V

3

1

Rear panel

Front panel

Port

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM11

E-12

 Adjusting the subwoofer before use

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and

the main speakers by following the procedures described below.

Rear panel

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

OFF

POWER

ON

VOLUME

010

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

OFF

LOW

HIGH

LOW

HIGH

HIGH CUT

VOLUME

010

OFF

POWER

ON

3

1, 6

5

Automatic power-switching function

If the source being played is stopped and the input signal

is cut off for 7 to 8 minutes, the subwoofer automatically

switches to the standby mode. (When the subwoofer

switches to the standby mode by the automatic power-

switching function, the power indicator lights up in red.)

When you play a source again, the power of the

subwoofer turns on automatically by sensing audio signals

input to the subwoofer.

This function will operate by sensing a certain level of low

frequency input signal. Usually set the AUTO STANDBY

switch to the LOW position. However, if the power is not

switched to ON or STANDBY smoothly, set the switch to

the HIGH position. In the HIGH position, the power will

turn on even with a low level of input signal. But please be

aware that the subwoofer may not switch to the standby

mode when there is an extremely low input signal.

* The power might turn on unexpectedly by sensing noise

from other appliances. If that occurs, set the AUTO

STANDBY switch to the OFF position and use the

POWER switch to switch the power between ON and

OFF manually.

* This function detects the low-frequency components

below 200 Hz of the input signals (i.e., the explosion in

the action movie, the sound of the bass guitar or the

bass drum, etc.).

* The minutes required to switch the subwoofer to the

standby mode might change by sensing noise from

other appliances.

This function is available only when the power of the

subwoofer is on (by pressing the POWER switch).

NS-P230-236 ENG(02.5.8)a 02.5.8, 9:59 PM12

English

E-13

1 Set the VOLUME control to minimum (0).

2 Turn on the power of all the other

components.

3 Press the POWER switch to the ON position.

* The power indicator on the front panel lights

up in green.

4 Play a source containing low-frequency

components and adjust the amplifier’s

volume control to the desired listening level.

5 Set the HIGH CUT switch to the LOW or

HIGH position.

This subwoofer is designed so that the

optimum tone balance between the subwoofer

and the main speakers is obtained when this

switch is set to the LOW position. The tone

balance may change, however, depending on

the room size, the distance from the subwoofer

to the main speakers, and so on. If necessary,

switch it to the HIGH position.

6 Increase the volume gradually to adjust the

volume balance between the subwoofer and

the main speakers.

Normally, set the control to the level where you

can obtain a little more bass effect than when

this unit is not used. If the desired response

cannot be obtained, adjust the HIGH CUT

switch and the VOLUME control again.

● Once the volume balance between the subwoofer and

the main speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control.

However, if you change the main speakers (NX-230P)

to others, you must make this adjustment again.

● For adjusting the VOLUME control and the HIGH CUT

switch, refer to “Frequency characteristics” below.

20 50 100 200 500Hz

40

50

60

70

80

90

10 0

YST-SW005

 Frequency characteristics

Fig. 1 shows the frequency characteristics of the subwoofer

with each position (HIGH/LOW) of the HIGH CUT switch.

HIGH CUT

LOW

HIGH

VOLUME

0I0

Fig. 2 shows the optimum volume level with the HIGH CUT

switch at the HIGH position, and the frequency

characteristics when the subwoofer is combined with NX-

230P.

Fig. 1

Fig. 2

NX-230P

20 50 100 200 500Hz

40

50

60

70

80

90

10 0

HIGH CUT

LOW

HIGH CUT

HIGH

NS-P230-236 ENG(02.5.8)a 02.5.8, 10:00 PM13

E-14

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY

(for YST-SW005)

The theory of Yamaha Active Servo Technology has been

based upon two major factors, the Helmholtz resonator and

negative-impedance drive. Active Servo Processing

speakers reproduce the bass frequencies through an “air

woofer”, which is a port or opening in the speaker’s cabinet.

This opening is used instead of, and performs the functions

of, a woofer in a conventionally designed speaker system.

Thus, signals of low amplitude within the cabinet can,

according to the Helmholtz resonance theory, be outputted

from this opening as waves of great amplitude if the size of

the opening and the volume of the cabinet are in the correct

proportion to satisfy a certain ratio.

In order to accomplish this, moreover, the amplitudes within

the cabinet must be both precise and of sufficient power

because these amplitudes must overcome the “load”

presented by the air that exists within the cabinet.

Thus it is this problem that is resolved through the

employment of a new design in which the amplifier supplies

special signals. If the electrical resistance of the voice coil

could be reduced to zero, the movement of the speaker unit

would become linear with respect to signal voltage. To

accomplish this, a special negative-impedance output-drive

amplifier for subtracting output impedance of the amplifier is

used.

By employing negative-impedance drive circuits, the

amplifier is able to generate precise, low-amplitude, low-

frequency waves with superior damping characteristics.

These waves are then radiated from the cabinet opening as

high-amplitude signals. The system can, therefore, by

employing the negative-impedance output drive amplifier

and a speaker cabinet with the Helmholtz resonator,

reproduce an extremely wide range of frequencies with

amazing sound quality and less distortion.

The features described above, then, are combined to be the

fundamental structure of the conventional Yamaha Active

Servo Technology.

Our new Active Servo Technology — Advanced Yamaha

Active Servo Technology — adopted Advanced Negative

Impedance Converter (ANIC) circuits, which allows the

conventional negative impedance converter to dynamically

vary in order to select an optimum value for speaker

impedance variation. With this new ANIC circuits, Advanced

Yamaha Active Servo Technology can provide more stable

performance and improved sound pressure compared with

the conventional Yamaha Active Servo Technology, resulting

in more natural and dynamic bass reproduction.

High-amplitude

bass sound

Cabinet

Port

Air woofer

(Helmholtz resonator)

Active Servo

Processing

Amplifier

Signals

Signals of low amplitude

Advanced Negative-

impedance Converter

NS-P230-236 ENG(02.5.8)a 02.5.8, 10:00 PM14

English

E-15

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if

the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

Problem

No sound.

Sound level is too low.

What to Do

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Cause

Speaker cables are not connected

securely.

Speaker cables are not connected

correctly.

For YST-SW005

Problem

Power is not supplied even

though the POWER switch is set

to the ON position.

No sound.

Sound level is too low.

The subwoofer does not turn on

automatically.

The subwoofer does not turn into

the standby mode automatically.

The subwoofer turns into the

standby mode unexpectedly.

The subwoofer turns on

unexpectedly.

What to Do

Connect it securely.

Turn the VOLUME control to the right

(clockwise).

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Play a source sound with bass

frequencies.

Set the HIGH CUT switch to the “HIGH”

position.

Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

Set the POWER switch to the ON

position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

Cause

The power plug is not securely

connected.

The VOLUME control is set to 0.

Speaker cables are not connected

securely.

Speaker cables are not connected

correctly.

A source sound with few bass

frequencies is played.

It is influenced by standing waves.

The POWER switch is set to the OFF

position.

The AUTO STANDBY switch is set to

the OFF position.

The level of input signal is too low.

There is an influence of noise

generated from external appliances etc.

The AUTO STANDBY switch is set to

the OFF position.

The level of input signal is too low.

There is an influence of noise

generated from external appliances etc.

NS-P230-236 ENG(02.5.8)a 02.5.8, 10:00 PM15

E-16

SPECIFICATIONS

 NX-230P, NX-C230

Type ......... Full range acoustic-suspension speaker system

Magnetic shielding type

Driver ........................ 5 cm (2”) full range cone speaker x 2

Nominal Input Power ................................................. 30W

Maximum Input Power ............................................. 100W

Impedance .....................................................................6Ω

Frequency Response

<NX-230P>........................................... 100 Hz to 30 kHz

<NX-C230> ............................................ 75 Hz to 30 kHz

Sensitivity ................................................... 86 dB/2.83V/m

Dimensions (W x H x D)

<NX-230P>.......................... 72 mm x 164 mm x 111 mm

(2-13/16” x 6-7/16” x 4-3/8”)

<NX-C230> ......................... 300 mm x 72 mm x 110 mm

(11-13/16” x 2-13/16”x 4-5/16”)

Weight

<NX-230P>................................................. 0.9 kg (2 lbs.)

<NX-C230> ....................................... 1.1 kg (2 lbs. 7 oz.)

 YST-SW005

Type ............... Advanced Yamaha Active Servo Technology

Magnetic shielding type

Driver ....................................... 16 cm (6-1/2”) cone woofer

Amplifier Output

U.S.A. and Canada models ............................... 55 W/5Ω

Other models ..................................................... 50 W/5Ω

Frequency Response .............................. 30 Hz to 200 Hz

Power Supply

U.S.A. and Canada models .................... AC 120V, 60 Hz

U.K. and Europe models ........................ AC 230V, 50 Hz

Australia model....................................... AC 240V, 50 Hz

China, Korean and General models

....................................... AC 110-120/220-240V, 50/60 Hz

Power Consumption .................................................60 W

(In the standby mode: 0.8 W)

Dimensions (W x H x D) ..... 200 mm x 365 mm x 375 mm

(7-7/8” x 14-7/20” x 14-3/4”)

Weight ............................................. 8.5 kg (18 lbs. 11 oz.)

* Specifications are subject to change without notice due

to product improvements.

NS-P230-236 ENG(02.5.8)a 02.5.8, 10:00 PM16

Français

F-1

●

Pour garantir les meilleures performances possibles, lire ce

manuel avec attention. Le garder dans un endroit sûr pour une

utilisation ultérieure.

●

Installer ces enceintes dans un endroit frais, sec et propre – loin

de fenêtres, sources de chaleur et d’endroits où les vibrations, la

poussière, l’humidité ou le froid sont importants. Eviter les

sources de bourdonnements (transformateurs, moteurs). Pour

éviter les incendies ou l’électrocution, ne pas exposer ces

enceintes à la pluie ni à l’humidité.

●

Pour éviter que le coffret ne gondole ou se décolore, ne pas

placer les enceintes à un endroit ou elles seront exposées aux

rayons directs du soleil ou à une trop forte humidité.

●

Eviter de placer les enceintes dans un endroit où elles

risqueraient d’être percutées par des objets tombants et/ou où

elles risqueraient d’être éclaboussées par du liquide.

Ne pas placer les objets suivants sur les enceintes :

●

D’autres composants, car ils pourraient endommager et/ou

décolorer la surface des enceintes.

●

Des objets inflammables (ex. des bougies), car elles

pourraient provoquer un incendie, endommager les enceintes

et/ou provoquer des blessures corporelles.

●

Des récipients contenant des liquides, car ils pourraient provoquer

une décharge électrique et/ou endommager les enceintes.

●

Ne pas placer les enceintes à un endroit où elles risquent d’être

renversées ou percutées par des objets tombants. Un endroit

bien stable améliorera aussi la qualité du son.

●

Si les enceintes sont placées sur la même étagère ou dans le

même meuble que le tourne-disque, un effet de retour sonore

risquera de se produire.

●

Le propriétaire du système est entièrement responsable du bon

positionnement et de la bonne installation du système.

YAMAHA décline toute responsabilité en cas d’accident causé par

un positionnement ou une installation inadéquats des enceintes.

●

Si des distorsions sonores se produisent, réduire le niveau

sonore en baissant la commande de volume de l’amplificateur.

Ne jamais laisser de “pincement” sonore se produire sur

l’amplificateur. Sinon, les enceintes risqueront d’être

endommagées.

●

Lorsqu’on utilise un amplificateur dont la puissance de sortie

nominale est supérieure à la puissance d’entrée nominale des

enceintes, il faut veiller à ne pas dépasser l’entrée maximale des

enceintes.

●

Ne pas essayer de nettoyer ces enceintes avec des diluants

chimiques, ceci endommagerait le fini. Utiliser un chiffon propre

et sec.

●

Ne pas essayer de modifier ni de réparer les enceintes.

Contacter un dépanneur YAMAHA qualifié en cas de nécessité

de réparation. Le coffret ne doit jamais être ouvert pour quelque

raison que ce soit.

●

Bien lire la section “EN CAS DE DIFFICULTE” concernant les

erreurs de fonctionnement communes avant de conclure que les

enceintes sont défecteuses.

Pour le YST-SW005

●

Ne pas utiliser cet appareil à l’envers. Il risque d’être en

surchauffe et de provoquer des dommages.

●

Ne pas forcer les commutateurs, les touches ou les câbles de

raccordement. Lors du déplacement de l’appareil, d’abord

débrancher la prise d’alimentation et les câbles le raccordant à

d’autres appareils. Ne jamais tirer sur les cordons.

PRECAUTIONS D’USAGE : Tenir compte des précautions

ci-dessous avant de faire fonctionner l’appareil.

Nous vous remercions d’avoir porté votre choix sur cet ensemble d’enceintes NS-P230/NS-P236 de YAMAHA.

●

Cet appareil possédant un amplificateur intégré, de la chaleur

sera irradiée par le panneau arrière. Par conséquent, placer

l’appareil à une certaine distance des murs, en laissant

suffisamment d’espace au-dessus, derrière et des deux côtés de

l’appareil afin d’éviter tout risque de dommage ou d’incendie. Ne

pas positionner non plus cet appareil dos au plancher ou à une

autre surface.

<Modèles pour le Royaume-Uni et l’Europe>

Laisser un espace d’au moins 20 cm au-dessus, derrière et des

deux côtés de l’appareil.

●

En utilisant un humidificateur, éviter la condensation à l’intérieur

de l’appareil en libérant la place autour de l’appareil ou en

évitant l’humidification extrême. La condensation peut causer un

feu, des dommages à l’appareil et/ou une électrocution.

●

Ne pas couvrir le panneau arrière de cet appareil avec quoi que

ce soit, journal, nappe, rideau, etc. afin de ne pas entraver la

dissipation de la chaleur. Si la température à l’intérieur de cet

appareil augmente, un incendie peut se déclarer et endommager

cet appareil et/ou causer une blessure corporelle.

●

Ne pas brancher cet appareil à une prise murale avant d’avoir

terminé toutes les connexions.

●

Le voltage à utiliser doit être le même que celui spécifiée sur le

panneau arrière. Utiliser cet appareil avec une plus haute tension

que celle spécifiée est dangereux et peut causer un incendie,

endommager cet appareil et/ou causer une blessure corporelle.

YAMAHA ne se tienda pas responsable d’aucun dommage

résultant de l’utilisation de cet appareil avec une tension autre

que spécifiée.

●

Pour prévenir tout dégât dû à la foudre, débrancher la prise

d’alimentation CA en cas d’orage.

●

Les sons de très basse fréquence produits par cet appareil

peuvent provoquer un sifflement sur le tourne-disque. Dans ce

cas, éloigner cet appareil du tourne-disque.

●

Cet appareil peut être endommagé si certains sons sont

continuellement émis à um niveau sonore élevé. Par exemple, si

des ondes sinusoïdales de 20–50 Hz d’un disque d’essai, des

sons de graves d’instruments électroniques, etc. sont émis en

continu ou si la pointe de lecture d’une platine tourne-disque

touche la surface d’un disque, réduire le niveau de volume pour

éviter d’endommager cet appareil.

●

Si une distorsion se fait entendre (par exemple des petits coups

secs intermittents ou un “martèlement”) sur cet appareil,

diminuer le niveau sonore. La lecture à très haut volume des

sons de basse ou des sons de basses fréquence de la bande

sonore d’un film, ou de passages de musique populaire de forte

intensité, sont susceptibles d’endommager ce système

d’enceintes.

●

Des vibrations générées par des fréquences supergraves

risquent de déformer les images sur un téléviseur. Dans ce cas,

éloigner cet appareil du téléviseur.

●

Lors du débranchement du cordon d’alimentation de la prise

murale, saisir la fiche ; ne pas tirer le cordon.

●

Lorsqu’on prévoit de ne pas utiliser cet appareil pendant

longtemps (pendant les vacances, par exemple), débrancher le

cordon d’alimentation CA de la prise murale.

●

VOLTAGE SELECTOR (Interrupteur de sélection de tension)

(Modèles pour la Chine, la Corée et général)

Le sélecteur de tension sur le

panneau arrière de cet appareil

doit être réglé sur la tension

locale AVANT de brancher

l’appareil sur une prise de

courant CA.

Les tensions sont de

110-120/220-240 V CA, 50/60 Hz.

110V-120V

VOLTAGE

SELECTOR

220V-240V

P230-236Fre(02.5.8)a 02.5.8, 10:00 PM1

F-2

TABLE DES MATIERES

DEBALLAGE ........ Intérieur du couvercle avant

PRECAUTIONS D’USAGE..............................1

ELEMENTS DE L’ENSEMBLE....................... 2

DISPOSITION DES ENCEINTES ................... 3

Positionnement du subwoofer ........................ 4

Positionnement d’enceinte centrale ................. 4

Montage des enceintes arrière (et d’enceinte

arrière centrale pour le NS-P236) ................... 5

Positionnement des enceintes principale/

arrière (et enceinte arrière centrale pour le

NS-P236)

..................................................... 6

CONNEXIONS ................................................ 7

Exemple de raccordement de base ................. 7

Raccordement des câbles d’enceinte aux

bornes d’entrée et de sortie des enceintes

....... 9

Raccordement du subwoofer aux bornes

de sortie d’enceintes de l’amplificateur .......... 10

UTILISATION DU SUBWOOFER

(YST-SW005) ................................................ 11

Les commandes et leurs fonctions ................ 11

Réglage du subwoofer avant l’utilisation ......... 12

Caractéristiques de fréquence ........................ 13

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY (pour YST-SW005) ............. 14

EN CAS DE DIFFICULTE ............................. 15

CARACTERISTIQUES TECHNIQUES......... 16

ELEMENTS DE L’ENSEMBLE

<NX-230P>

Système d’enceintes à gamme étendue et à suspension

acoustique utilisé pour les enceintes principales et

arrière (et enceinte arrière centrale pour le NS-P236)

<NX-C230>

Système d’enceintes à gamme étendue et à suspension

acoustique utilisé pour l’enceinte centrale

<YST-SW005>

Subwoofer à Active Servo Processing avec

amplificateur incorporé

● Ce subwoofer utilise Advanced YAMAHA Active Servo

Technology mise au point par YAMAHA pour la

reproduction de basses fréquences de meilleure qualité.

(Pour ce qui concerne Advanced YAMAHA Active Servo

Technology, se reporter à la page 14.) Ces basses

fréquences ajoutent un effet réaliste cinématographique

aux sons fournis par une chaîne stéréo.

● Ce subwoofer peut être facilement ajouté à votre chaîne

actuelle en le raccordant soit aux bornes d’enceintes soit

aux bornes de sortie de ligne (fiche Cinch) de

l’amplificateur.

● Le commutateur AUTO STANDBY vous évite d’avoir à

régler l’interrupteur POWER sur la position ON ou OFF.

L’ensemble d’enceintes “NS-P230” et “NS-P236” est conçu

pour être utilisé avec un système audio multi-canaux, telle

qu’une installation Home Cinéma.

Le NS-P230 contient quatre systèmes d’enceintes NX-230P,

un système d’enceinte NX-C230 et un subwoofer YST-

SW005.

Le NS-P236 contient cinq systèmes d’enceintes NX-230P, un

système d’enceinte NX-C230 et un subwoofer YST-SW005.

Pour les consommateurs canadiens

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondant de la

prise et pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à la

norme NMB-003 du Canada.

Mode veille

Si l’interrupteur POWER est mis sur la position ON et le

commutateur AUTO STANDBY sur la position HIGH ou LOW, cet

appareil passe en mode veille lorsqu’aucun signal ne parvient à

cet appareil pendant 7 ou 8 minutes.

Dans cet état, l’appareil consomme une très faible quantité de

courant.

AVERTISSEMENT

AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU

D’ÉLECTROCUTION, NE PAS EXPOSER L’APPAREIL À LA

PLUIE NI À L’HUMIDITÉ.

P230-236Fre(02.5.8)a 02.5.8, 10:00 PM2

Sayfa yükleniyor...

Yamaha NS-P230 El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha NS-P230 El kitabı

diğer dillerde

İlgili makaleler