Yamaha RX-V630RDS, DSP-AX630SE Kullanım kılavuzu

Marka: Yamaha

Model: RX-V630RDS, DSP-AX630SE

Kategori: AV alıcıları

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V874860

RX-V630RDS/DSP-AX630SE

RX-V630RDS AV Receiver

DSP-AX630SE AV Amplifier

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

0100V630(GB)-cv1/4 1/10/02, 3:41 PM1

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

left and right, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

–

Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

CAUTION

0101V630_Cau_EN(GB) 1/11/02, 7:39 PM2

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the package contents ................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................ 4

Remote control .......................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

PREPARATION

SPEAKER SETUP ................................................. 9

Speakers .................................................................... 9

Speaker placement .................................................... 9

Connecting the speakers .......................................... 10

CONNECTIONS .................................................. 13

Before connecting components ............................... 13

Connecting video components ................................ 14

Connecting audio components ................................ 16

Connecting the antennas ......................................... 17

Connecting an external amplifier ............................ 18

Connecting an external decoder .............................. 18

Connecting the power supply cords ........................ 19

Turning on the power .............................................. 19

SPEAKER MODE SETTINGS .......................... 20

ADJUSTING SPEAKER OUTPUT LEVELS .. 21

Before you begin ..................................................... 21

Using the test tone ................................................... 21

BASIC OPERATION

BASIC PLAYBACK ............................................ 23

Input modes and indications .................................... 25

Selecting a sound field program .............................. 26

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 29

Understanding sound fields ..................................... 29

Hi-Fi DSP programs ................................................ 29

CINEMA-DSP ...................................................... 30

Sound design of CINEMA-DSP ............................. 30

CINEMA-DSP programs ........................................ 32

TUNING

RX-V630RDS

......................................... 34

Automatic and manual tuning ................................. 34

Presetting stations .................................................... 35

Tuning in to a preset station .................................... 37

Exchanging preset stations ...................................... 37

RECEIVING RDS STATIONS

RX-V630RDS

.... 38

Description of RDS data ......................................... 38

Changing the RDS mode ......................................... 38

PTY SEEK function ................................................ 39

EON function .......................................................... 39

SLEEP TIMER ..................................................... 40

Setting the sleep timer ............................................. 40

Canceling the sleep timer ........................................ 40

RECORDING ....................................................... 41

ADVANCED OPERATION

SET MENU ........................................................... 42

Adjusting the items on the SET MENU .................. 42

1 SPEAKER SET (speaker mode settings) ............ 43

2 LFE LEVEL ........................................................ 45

3 SP DLY TIME (speaker delay time) ................... 45

4 D. RANGE (dynamic range) ............................... 46

5 L/R BALANCE (balance of the main left and

right speakers) ..................................................... 46

6 HP TONE CTRL (headphone tone control) ........ 46

7 I/O ASSIGN (input/output assignment) .............. 46

8 INPUT MODE (initial input mode) .................... 47

9 DISPLAY SET .................................................... 47

10MEM. GUARD (memory guard) ........................ 47

REMOTE CONTROL FEATURES ................... 48

Control area ............................................................. 48

Setting the manufacturer code ................................. 49

Clearing setup manufacturer codes ......................... 49

Controlling other components ................................. 50

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 51

ADJUSTING THE DELAY TIME ..................... 52

ADJUSTING THE PARAMETER SETTINGS

FOR PRO LOGIC

MUSIC ......................... 53

Changing parameter settings ................................... 53

PRO LOGIC Music parameter descriptions ....... 53

ADDITIONAL INFORMATION

TROUBLESHOOTING ...................................... 54

GLOSSARY .......................................................... 58

SPECIFICATIONS .............................................. 60

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM1

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “ES” and “DTS Digital Surround” are trademarks of

Digital Theater Systems, Inc.

FEATURES

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω)

Main: 75 W + 75 W

Center: 75 W

Rear: 75 W + 75 W

Rear center: 75 W

Multi-mode digital sound field

processing

◆ Dolby Pro Logic/Dolby Pro Logic decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES compatible decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

RX-V630RDS

◆ 40-Station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (Preset

editing)

Other features

◆ 96-kHz/24-bit D/A converter

◆ “SET MENU” for optimizing this unit for your

Audio/Video system

◆ Test tone generator for easier speaker balance

adjustment

◆ 6-channel external decoder input

◆ S-video signal input/output capability

◆ Component video input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Remote control with preset manufacturer codes

■ About this manual

• This document is the owner’s manual for both RX-V630RDS and DSP-AX630SE. Since DSP-AX630SE does not incorporate a

tuner, descriptions on tuning are not applicable for DSP-AX630SE. Illustrations for the RX-V630RDS are mainly used for

explanations.

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement

in operativity ability, and others. In this case, the product has priority.

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM2

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

POWER

SLEEP

CODE SET

STANDBY

TRANSMIT

6CH INPUT

SYSTEM

AUX

TV/CBL

REC

DISC SKIP

SET MENU

SELECT

PRESET/CH

TV INPUTTV MUTE

A/B/C/D/E

AUDIO

VOLUME

LEVEL

TEST

STEREO

EFFECT

RETURN

DISPLAY

TITLE

MUTE

AMP

POWER POWER

AVTV

VCR 1 VCR2/DVR

DVD

MD/CD-R TUNERCD

–

TV CHTV VOL

–

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

ROCK

CONCERT

JAZZ CLUB

3421

ENTER

+10

67 8

Installing batteries in the remote

control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

1 Press the part and slide off the battery

compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings on

the inside of the battery compartment.

3 Slide the cover back on so that it snaps into

place.

■ Notes on batteries

• Change all of the batteries if you notice a decrease in

the operating range of the remote control, that the

indicator does not flash, or the light becoming dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code that may have

been cleared.

AM loop antenna

(Europe, U.K., Australia and

Singapore models)

Indoor FM antenna

(U.S.A., Canada, China,

Korea and General models)

Batteries (4)

(AAA, R03, UM-4)

Remote control

GETTING STARTED

Checking the package contents

Check your package to make sure it contains the following items.

75-ohm/300-ohm antenna

adapter (U.K. model)

Front VIDEO AUX jack cap

RX-V630RDS

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM3

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

PRESET

TUNING

A/B/C/D/E

123 456

sa fd

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

iu po w e

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

90 ert8qw y

SET MENU

DSP-AX630SE

–

CONTROLS AND FUNCTIONS

Front panel

1 STANDBY/ON

Turns this unit on, or set it to the standby mode. When

you turn this unit on, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit will consume a small amount of

power in order to receive infrared-signals from the

remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks. Priority cannot be

set when 6CH INPUT is selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the OUT (REC) level.

7 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks. This audio takes priority over the source selected

with INPUT l / h (or the input selector buttons on the

remote control).

8 SILENT (PHONES jack)

Allows you enjoy DSP effect for private listening with

headphones. When you connect headphones, no signals

are output to the speakers or the OUTPUT jacks.

9 SPEAKERS A/B

Turns the set of main speakers connected to the A and/or

B terminals on or off.

(RX-V630RDS)

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM4

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

0 STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

q PROGRAM l / h

Selects the DSP program.

RX-V630RDS

PRESET/TUNING l / h

Selects preset station numbers 1 to 8 when the colon (:)

appears in the front panel display.

Selects the tuning frequency when the colon (:) does not

appear.

DSP-AX630SE

SET MENU –/+

Adjusts the setting on the SET MENU.

RX-V630RDS

A/B/C/D/E

Selects preset station groups A to E.

DSP-AX630SE

Selects the SET MENU mode.

r BASS

Adjusts the low-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the low-

frequency response.

t TREBLE

Adjusts the high-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the high-

frequency response.

y VIDEO AUX jacks

Inputs for audio and video signals from a portable

external source (game console, etc.). Set the input source

to V-AUX to enjoy source signals from these jacks.

When the VIDEO AUX jacks on the front panel are not

used, you can attach the provided front VIDEO AUX jack

cap as shown in the illustration. When the cap is not

attached, be sure retain it carefully.

RX-V630RDS

u RDS MODE/FREQ

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY

mode, RT mode, CT mode (if the station offers those

RDS data service) and/or frequency display mode in

turn.

i PTY SEEK MODE

Press this button to set the unit in the PTY SEEK

mode.

o PTY SEEK START

Press this button to begin searching for a station after

the desired program type has been selected in the PTY

SEEK mode.

p EON

Press this button to select the desired program type

(NEWS, INFO, AFFAIRS, SPORT) when you want to

tune in to a radio program of that type automatically.

a PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

between selecting a preset station number and tuning

(the colon (:) turns on or off).

This button is also used to exchange the assignment of

two preset stations with each other.

s TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and

manual.

d MEMORY (MAN’L/AUTO FM)

Stores the current station in the memory.

f FM/AM

Switches the reception band between FM and AM.

OPTICAL

S VID

VID

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM5

CONTROLS AND FUNCTIONS

POWER

SLEEP

CODE SET

STANDBY

TRANSMIT

6CH INPUT

SYSTEM

AUX

TV/CBL

REC

DISC SKIP

SET MENU

SELECT

PRESET/CH

TV INPUT

TV MUTE

A/B/C/D/E

AUDIO

VOLUME

LEVEL

TEST

STEREO

EFFECT

RETURN

DISPLAY

TITLE

MUTE

AMP

POWER POWER

AVTV

VCR 1 VCR2/DVR

DVD

MD/CD-R TUNERCD

–

TV CHTV VOL

–

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

ROCK

CONCERT

JAZZ CLUB

3421

ENTER

+10

67 8

Remote control

This section describes the remote control controls and

their functions. Make sure that the AMP mode is selected

before starting operation. See “REMOTE CONTROL

FEATURES” on pages 48 to 50.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 CODE SET

Used when setting up the manufacturer code (see page

49).

3 Input selector buttons

Select the input source and set the remote control to

operate the selected source component.

4 DSP program

Select DSP programs for the AMP position. Press a

button repeatedly to select a DSP program within that

group.

5 LEVEL

Selects the effect speaker channel to be adjusted.

6 Multi control section

Used when changing the setting and to implement the

settings.

7 TEST

Outputs the test tone to adjust the speaker levels.

8 TRANSMIT indicator

Flashes while the remote control is sending signals.

9 STANDBY

Sets this unit in the standby mode.

0 SYSTEM POWER

Turns on the power of this unit.

q SLEEP

Sets the sleep timer.

w 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks.

e AMP

Sets the remote control to the AMP mode for controlling

this unit.

r Å

Sets the remote control to operate other component (not

necessarily connected to this unit) without changing this

unit’s input source.

t VOLUME +/–

Increases or decreases the volume level.

y MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM6

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

VCR 1 VCR2/DVR

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FMAUTO/MAN'L MONO

TUNING MODE

VOLUMEINPUT

INPUT M0DE

6CH INPUT

30° 30°

Approximately 6 m (20 feet)

u STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

i SET MENU

Selects the SET MENU mode.

Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM7

CONTROLS AND FUNCTIONS

LCR

RC RR

LFE

VIRTUAL

DSP

PCM

MATRIX

SILENT

DIGITAL

EON

PS PTY

PTY HOLD

MUTE

SLEEP

STEREO

TUNED

MEMORY

AUTO

PRO LOGIC

VOLUME

DTS

MOVIE

THTR

ENTERTAINMENT

DOLBY DIGITAL

PRO

LOGIC

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

VCR2/DVR

1234

5789

qwert y

1 Processor indicators

Lights up when the t, g, VIRTUAL,

PRO LOGIC

DSP

are activated.

MATRIX lights up when the Dolby Digital EX decoder or

the DTS-ES compatible decoder is activated.

2 Input source indicator

Shows the current input source with a cursor.

3 MUTE indicator

Flashes while the MUTE function is on.

4 VOLUME level indicator

Indicates the volume level.

5 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

6 SILENT indicator

Lights up when headphones are connected while the

digital sound field processor is on.

7 Headphones indicator

Lights up when headphones are connected.

8 DSP program indicators

The name of the selected DSP program lights up when the

ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

9 Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

RX-V630RDS

0 RDS indicator

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

EON indicator lights up when an RDS station that

offers the EON data service is being received.

PTY HOLD indicator lights up while searching for

stations in the PTY SEEK mode.

q STEREO indicator

Lights up when this unit is receiving a strong signal

for an FM stereo broadcast while the “AUTO”

indicator is lit.

w TUNED indicator

Lights up when this unit is tuned to a station.

e MEMORY indicator

Flashes to show a station can be stored.

r AUTO indicator

Shows that this unit is in the automatic tuning mode.

Front panel display

(RX-V630RDS)

t SLEEP indicator

Lights up while the sleep timer is on.

y Input channel indicator

Indicates the channel components of input signals being

received.

0102V630_1-8_EN(GB) 1/11/02, 7:40 PM8

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using main left and

right speakers, rear left and right speakers, a center

speaker, and a rear center speaker. If you use different

brands of speakers (with different tonal qualities) in your

system, the tone of a moving human voice and other types

of sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for effect and surround sounds. The center speaker is

for the center sounds (dialog, vocals, etc.). The rear center

speaker supplements the rear (left and right) speakers and

provides for more realistic front-to-back transitions.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

playing back Dolby Digital or DTS signals. The

YAMAHA Active Servo Processing Subwoofer System is

ideal for natural and lively bass reproduction.

PREPARATION

Speaker placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the main left and right speakers an equal distance

from the ideal listening position. The distance between

each speaker and each side of the video monitor should

also be the same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible (such as directly over or under the

monitor) and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the

rear left and right speakers at the same height from the

floor as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

Note

• If you do not use any of effect speakers (rear, center and/or rear

center), change the settings of SPEAKER SET items at the

SET MENU to designate the signals to other terminals you

connect speakers to.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM9

SPEAKER SETUP

Connecting the speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit

and/or the speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be

connected to either the MAIN A or the MAIN B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM10

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

DVD

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

AC OUTLETS

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

Subwoofer

system

Rear center

speaker

Main B speaker

Center

speaker

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency

effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your

SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET

item “1E BASS” on the SET MENU to MAIN.

• Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote

control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 51).

Right Left

Main A speaker

Right Left

Left

The diagram shows the speaker layout in the listening

room.

(RX-V630RDS)

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM11

SPEAKER SETUP

SPEAKERS

MAIN

MPONENT VIDEO

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers,

the impedance of each speaker must

be 4 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

The impedance must be 6 Ω or

higher.

The impedance must be 6 Ω or

higher.

The impedance of each speaker must

be 6 Ω or higher.

If you use one set of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 16 Ω or higher.

[Canada model only]

The impedance of each speaker must

be 8 Ω or higher.

The impedance must be 8 Ω or

higher.

The impedance must be 8 Ω or

higher.

The impedance of each speaker must

be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(RX-V630RDS)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage

the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE

SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when

this unit is in the standby mode.

Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this

switch only when this unit is in the standby mode.

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM12

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Before connecting components

CAUTION

Do not connect this unit or other components to the

mains power until all connections between the

components have been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• When you connect other YAMAHA audio components

(such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same

number labels as !, #, $ etc. YAMAHA applies this

labeling system to all its products.

• After you have completed all connections, check them

again to make sure they are correct.

• The name of jack corresponds to input selector.

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. To enjoy multi-channel sound track

of DVD software, etc. with DSP effect, you need to make

digital connection. All digital input jacks are acceptable

for 96-kHz sampling digital signals.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

DVD

OUT

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

(RX-V630RDS)

AC OUTLETS

(page 19)

6CH INPUT jacks

(page 18)

DIGITAL OUTPUT jack

(page 16)

OUTPUT jacks

(page 18)

DIGITAL INPUT jacks

(pages 13-16)

Antenna input terminals

(page 17)

Speaker terminals

(pages 10-11)

Video component jacks

(pages 14-15)

Audio component jacks

(page 16)

SUBWOOFER OUTPUT

jack (page 11)

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM13

CONNECTIONS

Connecting video components

Refer to the connection examples on the next page.

■ Types of video jacks

There are three types of video jacks as follows:

1 VIDEO jack

Conventional composite video signal.

2 S VIDEO jack

Transmits color and luminance separately and achives

high-quality color reproduction.

3 COMPONENT VIDEO jacks

Transmit color difference (P

, P

) and luminance

separately and provide the best quality picture.

• Each type of video jack works independently. Signals

input through the composite video, S-video and

component jacks are only output through the

corresponding composite video, S-video, and

component jacks.

• Use a commercially available cable specified for

connecting each type of jacks.

•

The description of the component video jacks may differ

depending on the component (e.g. Y, C

, C

/Y, P

, P

/Y,

B-Y, R-Y etc.). When using these jacks, refer also to the

operation instructions for the component being connected.

■ Connecting a video monitor

Connect the video input jack on your video monitor to the

MONITOR OUT VIDEO jack.

Note

• If you connect this unit with a source component using S-video

(or Component video) jacks, you also need to connect your

video monitor using S-video (or Component video) jacks.

■ Connecting a DVD player/digital

TV/cable TV

Connect the optical digital audio signal output jack on

your component to the DIGITAL INPUT jack and

connect the video signal output jack on the component to

the VIDEO jack on this unit.

Then connect AUDIO jacks on your component to the

AUDIO jacks on this unit.

• If your video component has an S-video output or component

video output, connect the S-video signal output jack on the

component to the S VIDEO jack or connect the component

video signal output jacks on the component to the

COMPONENT VIDEO jacks.

• The AUDIO jacks are available for a video component which

does not have optical digital output jack. However, multi-

channel reproduction cannot be obtained with audio signals

input from AUDIO jacks.

■ Connecting a game console or

camcorder

Connect the optical digital audio signal output jack on

your video component to the OPTICAL jack on the front

panel and connect video signal output jack on the

component to the VIDEO jack on the front panel.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO

jack.

• The AUDIO jacks are available for a video component such as

a camcorder which does not have optical digital output jack.

■ Connecting a VCR or DVR (digital

video recorder)

Connect the audio signal input jacks on your video

component to the AUDIO OUT jacks and connect the

video signal input jack on the video component to the

VIDEO OUT jack on this unit for picture recording.

Connect the audio signal output jacks on your component

to the AUDIO IN jacks and connect the video signal

output jack on the component to the VIDEO IN jack on

this unit to play a source from your recording component.

Second VCR or digital video recorder can be connected

using VCR 2/DVR jacks.

• If your video component has an S-video input, connect the S-

video signal input jack on the component to the S VIDEO OUT

jack.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO IN

jack.

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• S-video and component video signals pass independently

through this unit’s video circuit. Make sure to connect this unit

to both a source component and a recording component using

the video jacks of the same system.

COMPONENT VIDEO

VIDEOS VIDEO

2 1 3

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM14

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

B/CBPR/CR

COMPONENT VIDEO

AUDIOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

V V

AUDIO

OUTPUT

AUDIO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

VIDEO

INPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

(RX-V630RDS)

indicates video cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR 1

DVD player

TV/digital TV/

cable TV

Game console or

camcorder

(RX-V630RDS)

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM15

CONNECTIONS

Connecting audio components

■ Connecting a CD player

Connect the coaxial digital output jack on your CD player

to the DIGITAL INPUT CD jack.

• The AUDIO jacks are available for a CD player which does not

have coaxial digital output jack.

■ Connecting a CD recorder or MD

recorder

Connect the optical digital signal input jack on your CD

recorder or MD recorder to the DIGITAL OUTPUT MD/

CD-R jack for digital recording.

Connect the optical digital output jack on your CD

recorder or MD recorder to the DIGITAL INPUT MD/

CD-R jack to play a source from your recording

component.

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

TUNER

D-TV

/CBL

OUT

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

VIDEO

VIDEOAUDIO

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

AUDIO

OPTICAL

INPUT

OPTICAL

OUTPUT

AUDIO

OUTPUT

COAXIAL

OUTPUT

DSP-AX630SE

(DSP-AX630SE)

indicates signal direction

CD player

CD recorder or

MD recorder

• The AUDIO jacks are available for an CD recorder or MD

recorder which does not have optical digital input or output

jack.

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• DIGITAL OUTPUT jack and analog OUT (REC) jacks are

independent. Only digital signals are output from DIGITAL

OUTPUT jack and analog signals from OUT (REC) jacks.

■

DSP-AX630SE

Connecting a tuner

Connect the output jacks on your tuner to the TUNER

jacks.

indicates optical cables

indicates coaxial cables

Tuner

indicates right analog cables

indicates left analog cables

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM16

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

D-TV

/CBL

DVD

ANT

GND

UNBAL.

VIDEO

OUT

MONI

VIDEO

TUNER

Ground (GND terminal)

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good

earth ground is a metal stake driven into

moist earth.

Indoor FM

antenna

(included)

AM loop antenna

(included)

Connecting the antennas

RX-V630RDS

11 (7/16)

8 (5/16)

6 (1/14)

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and

GND terminals.

3 Orient the AM loop antenna for the best

reception.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer

reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the

quality. Consult the nearest authorized YAMAHA

dealer or service center about the outdoor antennas.

Open the cover of the

included 75-ohm/300-ohm

antenna adapter.

Cut the external sleeve

of the 75-ohm coaxial

cable and prepare it for

connection.

Cut the lead wire and

remove it.

Insert the cable wire into the

slot, and clamp it with pliers.

Snap the cover into

place.

Unit:

mm (inch)

Lead wire

Clamp with

pliers.

Clamp

with

pliers.

Insert the wire

into the slot.

Both AM and FM indoor antennas are included with this

unit. In general, these antennas should provide sufficient

signal strength.

Connect each antenna correctly to the designated

terminals.

75-ohm/300-ohm antenna adapter (U.K. model)

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM17

CONNECTIONS

234

MAIN

CENTER

REAR

CENTER

OUTPUT

REAR

(SURROUND)

OUTPUT

SUB

WOOFER

Connecting an external amplifier

If you want to increase the power output to the speakers,

or want to use another amplifier, connect an external

amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for

output to an external amplifier, signals are output from the

SPEAKERS terminals as well.

1 SUBWOOFER jack

When using a subwoofer with built-in amplifier,

including the YAMAHA Active Servo Processing

Subwoofer System, connect the input jack of the

subwoofer system to this jack. Low bass signals

distributed from the main, center and/or rear channels are

directed to this jack in accordance with your SPEAKER

SET selections. The LFE (low-frequency effect) signals

generated when Dolby Digital or DTS is decoded are also

directed to this jack in accordance with your SPEAKER

SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main

left and right speakers by changing the settings of SPEAKER

SET item “1E BASS” on the SET MENU.

• Use the control on the subwoofer to adjust its volume level. It

is also possible to adjust the volume level by using this unit’s

remote control (see “ADJUSTING THE LEVEL OF THE

EFFECT SPEAKERS” on page 51).

2 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the

BASS and TREBLE settings.

3 REAR CENTER jack

Rear center channel line output jack.

4 CENTER jack

Center channel line output jack.

5 REAR (SURROUND) jacks

Rear channel line output jacks.

Connecting an external decoder

This unit is equipped with 6 additional input jacks (MAIN

left and right, CENTER, SURROUND left and right, and

SUBWOOFER) for discrete multi-channel input from an

external decoder, sound processor, or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, settings of

“1 SPEAKER SET” on the SET MENU do not apply (except

for “1F MAIN Lv”).

0103V630_9-18_EN(GB) 1/11/02, 7:40 PM18

Sayfa yükleniyor ...

Yamaha RX-V630RDS, DSP-AX630SE Kullanım kılavuzu

Marka: Yamaha

Model: RX-V630RDS, DSP-AX630SE

Kategori: AV alıcıları

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

PDF İndir

rapor

Diğer dillerde

español: Yamaha RX-V630RDS, DSP-AX630SE Manual de usuario
français: Yamaha RX-V630RDS, DSP-AX630SE Manuel utilisateur
italiano: Yamaha RX-V630RDS, DSP-AX630SE Manuale utente
svenska: Yamaha RX-V630RDS, DSP-AX630SE Användarmanual
čeština: Yamaha RX-V630RDS, DSP-AX630SE Uživatelský manuál
polski: Yamaha RX-V630RDS, DSP-AX630SE Instrukcja obsługi
Deutsch: Yamaha RX-V630RDS, DSP-AX630SE Benutzerhandbuch
português: Yamaha RX-V630RDS, DSP-AX630SE Manual do usuário
English: Yamaha RX-V630RDS, DSP-AX630SE User manual
dansk: Yamaha RX-V630RDS, DSP-AX630SE Brugermanual
русский: Yamaha RX-V630RDS, DSP-AX630SE Руководство пользователя
suomi: Yamaha RX-V630RDS, DSP-AX630SE Ohjekirja
Nederlands: Yamaha RX-V630RDS, DSP-AX630SE Handleiding
română: Yamaha RX-V630RDS, DSP-AX630SE Manual de utilizare

Yamaha RX-V630RDS, DSP-AX630SE Kullanım kılavuzu

Bu kılavuz için de uygundur

Yamaha RX-V630RDS, DSP-AX630SE Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler