Yamaha CP73 El kitabı

Marka: Yamaha

Modeli: CP73

Tip: El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

CP88

Owner’s Manual

CP88/CP73 Owner’s Manual

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing)

instructions in the literature accompa-

nying the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately five years. When replacement becomes

necessary, contact a qualified service representative to

perform the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of

knowledge relating to how a function or effect works

(when the unit is operating as designed) are not covered

by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully

and consult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

Model

Serial No.

Purchase Date

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

92-469- 1 (rear)

CP88/CP73 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur in all

installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

(weee_eu_en_02)

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate waste

handling.

For more information about collection and recycling of old products, please contact your local municipality, your

waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone: 714-522-9011

Type of Equipment: STAGE PIANO

Model Name: CP88, CP73

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

CP88/CP73 Owner’s Manual

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

CP88/CP73 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited

to, the following:

• Do not place the power cord near heat sources such as heaters

or radiators. Also, do not excessively bend or otherwise damage

the cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• Be sure to connect to an appropriate outlet with a protective

grounding connection. Improper grounding can result in

electrical shock.

• This instrument contains no user-serviceable parts. Do not

open the instrument or attempt to disassemble or modify the

internal components in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place on it any containers (such as

vases, bottles or glasses) containing liquids which might spill

into any openings. If any liquid such as water seeps into the

instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument

inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• When one of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet. Then have the device inspected by Yamaha service

personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

CP88/CP73 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality,

or possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an

outlet, always hold the plug itself and not the cord. Pulling by

the cord can damage it.

• Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

• Do not place the instrument in an unstable position where it

might accidentally fall over.

• Before moving the instrument, remove all connected cables, to

prevent damage to the cables or injury to anyone who might trip

over them.

• When setting up the product, make sure that the AC outlet you

are using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power switch and disconnect

the plug from the outlet. Even when the power switch is turned

off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time, make

sure to unplug the power cord from the wall AC outlet.

• Before connecting the instrument to other electronic

components, turn off the power for all components. Before

turning the power on or off for all components, set all volume

levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the

gaps on the panel. This could cause physical injury to you or

others, damage to the instrument or other property, or

operational failure.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons,

switches or connectors.

• Do not use the instrument/device or headphones for a long

period of time at a high or uncomfortable volume level, since

this can cause permanent hearing loss. If you experience any

hearing loss or ringing in the ears, consult a physician.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or

destroyed.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum

level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/Power cord

Location

Connections

Handling caution

DMI-5 2/2

CP88/CP73 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property,

follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric

devices. Otherwise, the instrument, TV, or radio may

generate noise. When you use the instrument along

with an application on your iPad, iPhone or iPod

touch, we recommend that you set “Airplane Mode” to

“ON” on that device in order to avoid noise caused by

communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage

to the internal components or unstable operation.

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel or

keyboard.

 Maintenance

• When cleaning the instrument, use a soft and dry/

slightly damp cloth. If the panel (front, side and

bottom, excepting the controllers and the keyboard) is

dirty, wipe the dirt away using a cloth moistened with a

neutral detergent solution and tightly wrung out.

Following this, wipe away the detergent solution using

a cloth soaked in water and tightly wrung out. Do not

use paint thinners, solvents, alcohol, or chemical-

impregnated wiping cloths.

• During extreme changes in temperature or humidity,

condensation may occur and water may collect on the

surface of the instrument. If water is left, the wooden

parts may absorb the water and be damaged. Make sure

to wipe any water off immediately with a soft cloth.

 Saving data

• Edited Live set sound and settings of MENU/

SETTINGS screens are lost when you turn off the

power to the instrument. This also occurs when the

power is turned off by the Auto Power Off function

(page 21). Save the data to the instrument, or to USB

flash drive/an external device such as a computer

(page 23). However, the data saved to the instrument

may be lost due to some failure, an operation mistake,

etc. Save your important data onto USB flash drive/an

external device such as a computer (page 23). Before

using a USB flash drive, make sure to refer to page 24.

• To protect against data loss through USB flash drive

damage, we recommend that you save your important

data onto spare USB flash drive or an external device

such as a computer as backup data.

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio

data is strictly prohibited except for your personal use.

• This product incorporates and bundles contents in

which Yamaha owns copyrights or with respect to

which Yamaha has license to use others' copyrights.

Due to copyright laws and other relevant laws, you are

NOT allowed to distribute media in which these

contents are saved or recorded and remain virtually the

same or very similar to those in the product.

* The contents described above include a computer

program, Accompaniment Style data, MIDI data,

WAVE data, voice recording data, a score, score data,

etc.

* You are allowed to distribute medium in which your

performance or music production using these

contents is recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About this manual

• The illustrations and LCD screens as shown in this

manual are for instructional purposes only, and may

appear somewhat different from those on your

instrument.

• iPhone, iPad, Logic Pro are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• IOS is a trademark or registered trademark of Cisco in

the U.S. and other countries and is used under license.

• Cubase is a registered trademark of Steinberg Media

Technologies GmbH.

• Ableton Live is a trademarks of Ableton AG.

• Pro Tools® is a registered trademark of Avid

Technolog y, Inc.

• The company names and product names in this

manual are the trademarks or registered trademarks of

their respective companies.

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the rear

of the unit. You should note this serial number in the space

provided below and retain this manual as a permanent

record of your purchase to aid identification in the event of

theft.

Model No.

Serial No.

(rear_en_01)

CP88/CP73 Owner’s Manual

Welcome

Thank you for purchasing the Yamaha CP88 or CP73.

This instrument is a Stage Piano designed especially for live performance.

Please read this Owner’s Manual carefully before using the instrument in order to take full advantage of its various

features. When you have finished reading the manual, keep it in a safe, accessible place, and refer to it when you need to

better understand an operation or function.

Accessories

•Owner’s Manual (this book)

•Power cord

•Foot pedal (FC3A)

Main Features

 Authentic acoustic- and electric-piano sounds of unparalleled quality

Building on our decades of experience in the production of stage pianos, we have meticulously adjusted the sound of

each individual key and realized perfect balance over the full length of the keyboard, creating full-bodied piano tones

ideal for solo performances and authentically rich sounds well suited for playing within an ensemble. Furthermore, by

analyzing and replicating the sound-producing mechanisms of classic electric pianos using cutting-edge technologies,

we have been able to achieve an extremely smooth response in the CP88 and CP73 keyboards.

 Weighted hammer-action keyboards

CP series employ a keyboard with a weighted hammer-action design that is virtually indistinguishable from an

acoustic piano. The CP88’s NW-GH3 (Natural Wood Graded Hammer keyboard with synthetic ebony and ivory

keytops) keyboard reproduce a touch of grand piano by giving all keys an authentic resistance that increases from the

top register to the lower. And the CP73 features a BHS (Balanced Hammer Standard) keyboard with matte black

keytops, perfect for performing as an electric piano as well.

 Design embodies high-class appearance and portability

Featuring a stylish, finely crafted aluminum exterior in a light, compact package, the CP88 and CP73 project an

exceptionally professional appearance and provide convenient portability onstage.

 User interface provides direct, intuitive control required for live performance

The three Voice sections—Piano, E.Piano and Sub—are indicated clearly on the top panel, giving you all the

controllers you need onstage, allowing you to directly adjust each parameter as you need while you play. The LED

indicator lamps show you the selected Voice, letting you fully concentrate on your performance. Moreover, you can

enhance sounds on-the-fly, adding various effects to suit your performance as you play.

 Connect with other devices and expand your performance potential

Comprehensive MIDI controls and powerful Master Keyboard features make it easy to connect and use the

instrument with software synthesizers and external MIDI devices. Moreover, the instrument has a built-in USB

Audio/MIDI interface for convenient recording functions in home and professional studios, as well as onstage

performance power.

CP88/CP73 Owner’s Manual

Contents

PRECAUTIONS..................................................................5

NOTICE ...............................................................................7

Information..........................................................................7

Welcome...............................................................................8

Accessories ...........................................................................8

Main Features ......................................................................8

Controls and Functions 10

Front Panel........................................................................ 10

Settings of LCD and the indicator lamp ........... 10

Live Set......................................................................... 12

Storing a Live Set Sound ..................................... 12

Swapping Live Set Sounds .................................. 13

Copying a Live Set Sound ................................... 13

Piano section............................................................... 14

Copying a section................................................. 14

Electric Piano section ................................................ 15

Sub section .................................................................. 16

Delay section/Reverb section.................................... 16

Master EQ ................................................................... 17

Rear Panel.......................................................................... 18

Setting Up 20

Power Supply .................................................................... 20

Connecting Speakers or Headphones ........................... 20

Turning On and Off......................................................... 20

Auto Power Off Function................................................ 21

Restoring the Factory Default Settings (Factory Reset)

Basic Structure & Display Content 21

Selecting Voices ................................................................ 21

Exiting from the Current Screen.................................... 21

Display Configuration ..................................................... 21

Editing File Names/Live Set Sound Names .................. 22

Saving / Loading Data 23

Saving the settings to a USB flash drive ........................ 23

Loading the settings from a USB flash drive ................ 23

Using with Other MIDI Devices 25

Controlling a synthesizer or tone generator module from

this instrument ................................................................. 25

Controlling this instrument from an external MIDI

keyboard or synthesizer................................................... 25

Using with a Computer 26

Connecting to a computer .............................................. 26

Connecting an iPhone or iPad ....................................... 27

MENU LIST 28

SETTINGS LIST 33

DATA LIST 37

Live Set Sound List ........................................................... 37

Voice List........................................................................... 39

Control Change Number List......................................... 40

MIDI................................................................................... 43

MIDI Data Format ........................................................... 44

MIDI Data Table .............................................................. 46

MIDI Implementation Chart.......................................... 50

Appendix 51

Display Messages.............................................................. 51

Troubleshooting ............................................................... 52

Specifications .................................................................... 54

Index................................................................................... 55

CP88/CP73 Owner’s Manual

Front Panel

Pitch bend lever

Use this controller to smoothly raise or lower the pitch of

played notes. When you release it, the lever will

automatically spring back to the original position, and

the pitch will return to normal.

The range can be set for each sections from the

[SETTINGS] button → “Controllers” → “Bend Range”

(page 36).

Modulation lever

Use this lever to apply vibrato to the sound. The vibrato

depth can be set for each section from the [SETTINGS]

button → “Controllers” → “P.Mod Depth” (page 36).

When the “Rotary” insertion effect of the Sub section is

selected, this lever functions as a controller to switch the

rotary speed (Fast, Slow).

[MASTER VOLUME] knob

Use this knob to adjust the overall volume of the

instrument.

LCD

Displays the system messages, parameter settings, and a

range of other information depending on the function

currently being used.

 Settings of LCD and the indicator lamp

To make the following settings, press the [MENU]

button → “Control Panel” → “Display Lights.”

Encoder dial/[ENTER] button

Use this dial to display the Live Set view and to edit the

currently selected parameter. In the MENU screens and

the SETTINGS screens, move the cursor (highlighted)

up or down to select an event for editing.

Also, pressing this dial is equivalent to pressing the

[ENTER] button. Use this button to determine the

selected parameter or to execute each operation.

[EXIT] button

The MENU screens and the SETTINGS screens are

organized according to a hierarchical structure. Press

this button to exit from the current screen and return to

the previous level in the hierarchy.

Controls and Functions

Live Set

(page 12)

Piano section

(page 14)

Section

For setting “Off” to light the lamps of each

section that is linked with the Voice section

[ON/OFF] switches, or “On” so that they

continuously light.

Ins Effect

For setting “Off” to light each insertion effect

lamps linked with the Insertion effect [ON/

OFF] buttons, or “On” to continuously light the

lamps.

LCD SW

Set this to “On” to light the Top screen, or “Off”

to turn off. However, regardless of this setting,

the various setting screens such as the MENU

screens and the SETTINGS screens are

always lit.

LCD

Contrast

For adjusting the contrast of the LCD.

Controls and Functions

CP88/CP73 Owner’s Manual

[PANEL LOCK] button

Use this button to switch the panel lock function on and

off. When this is set to “On,” control panel operations are

disabled, ensuring that settings cannot be inadvertently

changed. Pressing the button alternates between lock and

unlock. While the panel lock is engaged, will appear

on the top left corner of the LCD display.

NOTE

Panel lock settings can be made individually for the following

areas from the [MENU] button  “Control Panel”  “Panel Lock

Settings.”

A. Live Set

B. Piano/E.Piano/Sub

C. Delay/Reverb

D. Master EQ

[TUNE] button

Use this button to set the tuning for the entire instrument

(414.72 – 466.78 Hz). Press the [TUNE] button, and then

use the Encoder dial to change the value.

NOTE

The default value is 440.00 Hz.

[TOUCH] button

Displays the screen to select a curve for determining how

the actual velocities will be generated according to the

strength with which you play notes on the keyboard. The

available settings are as follows. The setting also can be

changed from the [MENU] button → “General” →

“Keyboard/Pedal” → “Touch Curve” (page 29).

[MENU] button

Use this button to call up the screens for making overall

system settings.

Electric Piano section

(page 15)

Sub section

(page 16)

Delay section (page 17)

Reverb section (page 17)

Master EQ

(page 17)

ABCD

Settings Characteristics

Normal

This curve produces velocities in direct proportion

to the strength of your keyboard playing. This is

the most common type of curve.

Soft

This curve makes it easier to produce high

velocities across the entire keyboard.

Hard

This curve makes it more difficult to produce high

velocities across the entire keyboard.

Wide

This curve accentuates your playing strength by

producing lower velocities in response to softer

playing and louder velocities in response to

harder playing. You can use this setting to expand

the dynamic range of your performances.

Fixed

This curve produces the same amount of sound

change, regardless of how hard or soft you play

the keyboard. The fixed velocity can be set from

the [MENU] button



“General”



“Keyboard/

Pedal”



“Fixed Velocity.”

Controls and Functions

CP88/CP73 Owner’s Manual

Live Set Sound [1] – [8] button

Use these buttons to call up the stored Live Set Sounds.

PAGE [-]/[+] buttons

Use these buttons to switch the Live Set Pages. The Live

Set Sound switches accordingly.

[STORE] button

Use this button to store the edited Live Set Sound.

Settings of the sections listed below and their parameters

can be stored. Stored settings will be retained when this

instrument is turned off.

• Piano section

• Electric Piano section

•Sub section

•Delay section

•Reverb section

• SETTINGS (includes Split Point and Transpose)

NOTE

The Master EQ settings cannot be stored in Live Set Sound.

 Storing a Live Set Sound

Press the [STORE] button.

Select a Live Set Sound you wish to store the

currently edited Live Set Sound setting into.

2. Press the [ENTER] button to execute.

A “Completed.” message will appear on the screen,

and then return to the Top screen.

Live Set

Live Set Sound

This is a combination of Voices/effects, consisting of the

sounds of all Voice sections – Piano section (page 14),

Electric Piano section (page 15), and Sub section

(page 16) and effects of the Delay section (page 17) and

the Reverb section (page 17). You can combine sounds

and insertion effects, to create and store a custom Live

Set Sound.

The Live Set feature supports SSS (Seamless Sound

Switching), ensuring that the sound does not cut off even

when changed, resulting in smoother transitions

between Live Set Sounds and a more natural

performance.

NOTE

If you wish to mute the sound continued by the effect of SSS,

press again the currently selected Live Set Sound button.

Live Set

Combines the Live Set Sounds [1] – [8] into one page.

With the default settings (factory settings), the preset

Live Set Sounds are installed in from page 1 to page 10.

Live Set Sound

Piano

Electric Piano

Sub

Delay

Reverb

SETTINGS

20 pages

Live Set

Live Set View

Displays a Live Set Page (Live Set Sound [1] – [8]) in a

single screen, for convenient overall view of the available

sounds. To open the Live Set View, turn the Encoder dial

when at the Top screen. The will appear on the left of

the currently selected Live Set Sound. To change the Live

Set Sound in Live Set View, turn the Encoder dial to

select a Live Set Sound, and press the [ENTER] button to

return to the Top screen. To have the Live Set view shown

on the Top screen, change the settings of “Live Set View

Mode” to “Keep” (page 31).

Live Set View Mode

Controls and Functions

CP88/CP73 Owner’s Manual

NOTE

If you wish to store the currently edited settings to another

Live Set Sound, use the Encoder dial to select the Live Set

Sound which is to be the store destination. Press the

keyboard to confirm that the sound has been changed to the

edited settings.

NOTICE

• Keep in mind that the settings will be overwritten

when you select an existing Live Set Sound (including

one of the preset Live Set Sounds). Proceed with

caution.

• The settings currently be edited will be lost if you

select another Live Set Sound before storing, or turn

off the power.

NOTE

• Edits made to a Live Set Sound are normally lost if not

stored before selecting a different Live Set Sound;

however, by using the “Edit Recall” function, you can recall

the last edited condition (page 32).

•You can download the preset Live Set Sounds from

Soundmondo. Soundmondo is an iOS application for

storing and managing Voice data.

• Please refer to the following Yamaha web page for more

details on Soundmondo.

http://www.yamaha.com/kbdapps/

 Swapping Live Set Sounds

1. Select the Live Set Sound you wish to swap.

2. Call up the Swap screen.

[MENU] button → “Job” → “Live Set Manager” →

“Swap.”

3. Select a Live Set Sound.

Use the Encoder dial to select a Live Set Sound to swap,

and then press the [ENTER] button. The messages

“Executing..” → “Completed.” will appear on the screen,

and then return to the Top screen.

 Copying a Live Set Sound

1. Select the Live Set Sound you wish to copy.

2. Call up the Copy screen.

[MENU] button → “Job” → “Live Set Manager”→

“Copy.”

3. Select the desired Live Set Sound location.

Use the Encoder dial to select the Live Set Sound

intended for the store destination, and then press the

[ENTER] button. e messages “Executing..” →

“Completed.” will appear on the screen, and then

return to the Top screen.

[SPLIT POINT] button

Use this button to change the Split Point. Turn the

Encoder dial or press the key you wish to assign as the

Split Point. The setting will be stored in Live Set Sound.

[TRANSPOSE] button

Use this button to adjust the pitch of the keyboard up or

down in semitone steps. The settings can be stored to the

Live Set Sound. The settings can be changed from the

[SETTINGS] button → “Function” → “Sound Transpose”

(page 33).

[SETTINGS] button

Use this button to call up the SETTINGS screens. In the

SETTINGS screens, you can make detailed settings for

the current selected Live Set Sound (page 33), which will

then be stored for the Live Set Sound.

Split

This function allows you to play different Voices with the

left and right hands. The point on the keyboard that

separates the left hand section and the right hand section

of the keyboard is called the “Split Point.”

NOTE

• The default setting is “G2”.

• The lowest note of the right hand section is referred as the

Split Point.

• The Split Point can be changed from the [SETTINGS] button

 “Function”  “Split Point” (page 33).

Controls and Functions

CP88/CP73 Owner’s Manual

Voice section [ON/OFF] switch

Use these switches to determine whether the

corresponding Voice section is enabled (ON) or not

(OFF). When these indicator lamps are lit, the

corresponding Voice sound is produced when you play

the keyboard.

 Copying a section

The settings of each Voice section can be copied with the

following operation.

1. Select the Voice section you wish to copy.

Select the Live Set Sound which contains the Voice

section you wish to copy. Press the [MENU] button →

“Job” → “Section Manager” → “Copy,” then select the

Voice section you wish to copy.

A “Section copied.” message will appear on the

screen, and then return to the Top screen.

2. Select a Voice section you wish to paste.

Select the Live Set Sound which contains the Voice

section you wish to paste the copied section. Press the

[MENU] button → “Job” → “Section Manager” →

“Paste,” then select the Voice section you wish to

paste.

A “Section pasted.” message will appear on the

screen, and then return to the Top screen.

Voice category selector

The Voices in each Voice section are divided into four

categories. To select a Voice, select a Voice category first.

Voice select switch

Use this switch to select one of the Voices of the category

selected with the Voice category selector. For

information about the Voices, refer to page 39.

Voice number display

Displays the currently selected Voice numbers.

SPLIT [L R] button

Press these buttons to alternate between the keyboard-

split settings of each Voice section. The area for which

the indicator lamp is lit will sound.

NOTE

The Split Point can be changed from the [SPLIT POINT] button

(page 13), also from the [SETTINGS]  “Function”  “Split

Point” (page 33).

OCTAVE [-2 -1]/[+1 +2] buttons

Use these buttons to change the octave range of the

keyboard. To restore the normal octave setting, press

both buttons simultaneously.

[VOLUME] knob

Use these knobs to adjust the volume of each Voice

section.

[TONE] knob

Use these knobs to adjust the tone of each Voice section.

Setting the knob to the center position produces a flat,

evenly balanced sound. Turn the knob to the right

(clockwise) to boost the higher and lower ranges. Turn

the knob to the left (counter-clockwise) to cut the higher

range and the lower range.

DAMPER RESONANCE [ON/OFF] button

Use this button to switch the damper resonance effect on

and off. This simulates the rich sound of open strings

produced when the damper pedal of a piano is pressed.

Insertion effect [ON/OFF] button

Use this button to apply the insertion effects.

NOTE

To more easily confirm the setting value when the display light is

turned off, you can turn the light on from the [MENU] button 

“Control Panel”  “Display Lights”  “Ins Effect” (page 30).

Insertion effect switch button

Use this button to switch among the following effects.

The indicator lamp of the selected effect is lit.

Piano section

Voice section Voice category

Piano

Grand Piano, Upright Piano, CP,

Layered Piano

Electric Piano

Rd, Wr, Clv, DX

Sub

Pad/Strings, Organ, Chromatic Perc.,

Others

Effect Description

Compressor

Stereo compressor. To increase the

compressor effect, turn the [DEPTH] knob

to the right (clockwise).

Controls and Functions

CP88/CP73 Owner’s Manual

[DEPTH] knob

Use this knob to adjust the depth of the selected effect.

[DRIVE] knob

Use this knob to adjust the amount of the drive effect.

Simulates the distortion produced by a tube amp.

Insertion effect switch button

Use this button to switch among the following effects.

The indicator lamp of the selected effect is lit.

[DEPTH] knob

Use this knob to adjust the depth of the selected effect.

[RATE] knob

Use this knob to adjust the modulation speed of the

selected effect.

Insertion effect switch button

Use this button to switch among the following effects.

The indicator lamp of the selected effect is lit.

[DEPTH] knob

Use this knob to adjust the depth of the selected effect.

[SPEED] knob

Use this knob to adjust the modulation speed of the

selected effect.

Distortion

Monaural compressor plus distortion.

Settings from the left-most to the center of

the [DEPTH] knob applies compression.

Turning the [DEPTH] knob from the center

to right (clockwise) increases the amount of

distortion.

Drive

Drive effect. Turning the [DEPTH] knob to

the right (clockwise) increases the amount

of distortion, with the maximum value

producing an AM radio-like tone.

Chorus

Stereo chorus. Turning the [DEPTH] knob to

the right (clockwise) increases the amount

of chorus effect.

Electric Piano section

Effect Description

A.Pan

Auto pan built into vintage electric pianos. Turn the

[DEPTH] knob to adjust the effect depth, and turn

the [RATE] knob to adjust the effect speed.

Tre m

Tremolo built into vintage electric pianos. Turn the

[DEPTH] knob to adjust the effect depth, and turn

the [RATE] knob to adjust the effect speed.

R.Mod

Ring modulator. Turn the [DEPTH] knob to adjust

the effect depth, and turn the [RATE] knob to

adjust the frequency. Depending on the settings of

the [RATE] knob, this effect also can be used as

tremolo.

Effect Description

T.Wa h

Wah responds to keyboard dynamics. Turn the

[DEPTH] knob to adjust the effect strength, and

turn the [RATE] knob to adjust the effect amount.

P. W a h

Wah synchronized to an expression pedal

connected to the FOOT CONTROLLER [2] jack.

Turn the [DEPTH] knob to adjust the amount of

distortion, and turn the [RATE] knob to adjust the

amount of resonance.

Comp

Stereo compressor. Turn the [DEPTH] knob to

adjust the effect depth, and turn the [RATE] knob

to adjust the sound volume.

Effect Description

Cho 1

Traditional Yamaha multiple chorus. Turn the

[DEPTH] knob to adjust the effect depth, and turn

the [SPEED] knob to adjust the speed.

Cho 2

Simulates a thick detune chorus produced by the

vintage TX816 tone generator. Turn the [DEPTH]

knob to adjust the effect depth, and turn the

[SPEED] knob to adjust the speed.

Flang

Stereo flanger. Turn the [DEPTH] knob to adjust

the feedback amount, and turn the [SPEED] knob

to adjust the speed.

Pha 1

Phaser applies a smooth and unique sweeping

effect. The sweeping effect can be changed by

turning the [DEPTH] knob to left/right. Turn the

[SPEED] knob to adjust the speed.

Pha 2

Standard phaser. Turn the [DEPTH] knob to adjust

the effect strength. Turn the [SPPED] knob to

adjust the speed.

Pha 3

Features two different phaser systems. Turn the

[DEPTH] knob to switch the depth of “Pha 1” and

“Pha 2.” Turn the [SPEED] knob to adjust the

speed.

Effect Description

Controls and Functions

CP88/CP73 Owner’s Manual

[ATTACK] knob

Use this knob to adjust the attack time.

[RELEASE] knob

Use this knob to adjust the release time.

NOTE

After you change a Live Set Sound, turning the [ATTACK] knob

or the [RELEASE] knob does not actually affect the sound until

their position reaches the set values of the currently selected

Live Set Sound. Until then, the value will be shown in

parentheses.

Insertion effect switch button

Use this button to switch among the following effects.

The indicator lamp of the selected effect is lit.

[DEPTH] knob

Use this knob to adjust the depth of the selected effect.

[SPEED] knob

Use this knob to adjust the modulation speed of the

selected effect.

Effect level display switch button

Use this button to select the desired Voice sections for

adjusting the send levels to delay and reverb effects. Turn

the [DEPTH] knobs of the Delay section and the Reverb

section to adjust the send levels from each Voice section.

Sub section

Effect Description

Cho/Fla

Chorus/Flanger. Turn the [DEPTH] knob to adjust

the effect depth. Turn the [SPEED] knob to adjust

the speed. Settings from the left-most to the center

of the [DEPTH] knob apply a chorus effect, while

settings from the center to the right (clockwise)

apply a flanger effect (similar to the sound of jet).

Rotary

Rotary speaker. Turn the [DEPTH] knob to adjust

the balance between rotary speaker and horn

speaker. Turn the [SPEED] knob to adjust the

rotation speed. Turning the [DEPTH] knob to the

left applies the horn speaker, and turning to the

right applies the rotary speaker. Turning the

[SPEED] knob from the center to left decreases

the rotation speed, and turning the knob from the

center to right increases the speed. The speed can

be changed by using the Modulation lever.

Tre m

Standard tremolo. Turn the [DEPTH] knob to

adjust the effect depth, and turn the [SPEED] knob

to adjust the speed.

Dist

British hard rock type distortion. Turn the [DEPTH]

knob to adjust the amount of distortion, and turn

the [SPEED] knob to adjust the presence.

Effect

The CP88 and CP73 feature insertion effects and delay/

reverb effects that can be configured for each Voice

section, as well as a master EQ that affects all the Voice

sections in the same way. The illustration below shows

the audio signal path.

Delay section/Reverb section

Piano E. Piano Sub

Ins. Effect

(1 system)

Ins. Effect

(3 systems)

Ins. Effect

(2 systems)

Send

level

Delay / Reverb

Master EQ

Controls and Functions

CP88/CP73 Owner’s Manual

When all the indicator lamps of the Voice sections are lit,

the send levels from each Voice section can be adjusted

equally. When the send levels of each Voice section are

set individually, the indicator lamp of the [DEPTH] knob

is unlit. However, when the send levels are readjusted,

the indicator lamp of the [DEPTH] knob light, and the

send levels are changed from the previously set value.

 Delay section

DELAY [ON/OFF] switch

Use this switch to determine whether to apply (ON) the

delay effect or not (OFF). Delay effects create a delayed

version of the input signal, and as such, they can be used

for many different purposes, such as creating a sense of

spaciousness or thickening a sound.

[Analog/Digital] switch button

Use this button to switch between the analog delay and

the digital delay. The indicator lamp of the selected effect

is lit.

[DEPTH] knob

Use this knob to adjust the effect depth. Also you can

adjust the send level for each Voice section with the

Effect level display switch button.

[FEEDBACK] knob

Use this knob to adjust the feedback level output from

the delay that is returned to the input.

NOTE

The sound will be oscillated when the feedback level is set to

high levels. To reduce the oscillation, lower the feedback level, or

set the DELAY [ON/OFF] switch to OFF. If the Live Set Sound is

changed to another while the sound is still oscillating, the

controls of the delay section will not be effective in controlling the

oscillation. Press the currently selected Live Set Sound button

again to stop the oscillation.

[TIME] knob

Use this knob to set the feedback delay time.

 Reverb section

REVERB [ON/OFF] switch

Use this switch to determine whether to apply (ON) the

reverb effect or not (OFF). Reverb effects create a rich

special ambience of various performance environments,

such as a concert hall or a night club.

[DEPTH] knob

Use this knob to adjust the depth of the reverb effect.

Also use the Effect level display switch button to adjust

the effect level individually for each Voice section.

[TIME] knob

Use this knob to set the duration of the reverb effect

(max. 30 s).

MASTER EQUALIZER [ON/OFF] button

Use this button to determine whether to apply (ON) the

Master EQ or not (OFF). Master EQ adjusts the overall

tone of the sound.

NOTE

The Master EQ settings are a global control and cannot be

stored to a Live Set Sound.

[HIGH] knob

Use this knob to adjust the gain (-12 to +12) of the high

EQ band (5 kHz).

[MID] knob

Use this knob to adjust the gain (-12 to +12) of the mid

EQ band (100 to 10 kHz).

[FREQUENCY] knob

Use this knob to adjust the center frequency of the

midrange.

[LOW] knob

Use this knob to adjust the gain (-12 to +12) of the low

EQ band (80 Hz).

Effect Description

Analog

Typ ic al warm sound of analog delay. Use the

[DEPTH] knob to adjust the effect depth, the

[FEEDBACK] knob to adjust the number of

repeats, and the [TIME] knob to adjust the delay

time. The maximum delay time is 800 ms.

Digital

Clean digital delay. Use the [DEPTH] knob to

adjust the effect depth, the [FEEDBACK] knob to

adjust the number of repeats, and the [TIME] knob

to adjust the delay time. The maximum delay time

is 1,486 ms.

Master EQ

Controls and Functions

CP88/CP73 Owner’s Manual

Rear Panel

[STANDBY/ON] switch

For switching the instrument to standby or turning it on.

[AC IN] jack

For connecting the supplied AC power cord.

Music stand attachment holes

Use these two holes to attach a music stand (sold

separately).

USB [TO DEVICE] terminal

Use this terminal to connect a USB flash drive to this

instrument, for saving data you have created and loading

data you want to restore.

NOTE

Only USB flash drive can be recognized by this instrument. No

other USB devices (such as a hard disk drive, CD-ROM drive or

USB hub) can be used.

USB [TO HOST] terminal

This terminal lets you connect this instrument to a

computer, iPhone or iPad via a USB cable, allowing you

to transfer MIDI data and audio data between the

devices. Unlike MIDI, USB can handle multiple ports via

a single cable. For information about how this

instrument handles Ports, see page 25.

NOTE

•Audio data sending capability for the instrument is a maximum

two channels (one stereo channel) at a sampling rate of

44.1 kHz.

• For details on connecting an iPhone or iPad, refer to page 27.

MIDI [IN]/[OUT] terminals

With a standard MIDI cable (available separately), you

can connect an external MIDI instrument, and control it

from this instrument. Likewise, you can use an external

MIDI device (such as a keyboard or sequencer) to

control the sounds on this instrument.

FOOT SWITCH [SUSTAIN] jack

Use this jack to connect an FC3A Foot Switch (provided)

for use as a dedicated sustain pedal.

FOOT SWITCH [ASSIGNABLE] jack

Use this jack to connect a separately sold foot switch

(FC4A or FC5) in order to perform a range of freely

assignable functions such as a soft pedal, sostenuto

pedal, and switching Live Set Sounds. With the default

settings, “Live Set+” is assigned.

You can assign functions from the [MENU] button →

“General” → “Keyboard/Pedal” → “Foot Switch Assign”

(page 30). Refer to page 40 for a list of the parameters

that can be assigned to this instrument.

AC outlet

USB flash drive Computer

Controls and Functions

CP88/CP73 Owner’s Manual

FOOT CONTROLLER [1]/[2] jacks

Use these jacks to connect a separately sold foot

controller (FC7) in order to continuously control one of

various different assignable functions by foot, such as

volume and the tone of Voice sections. With the default

settings, “Expression” is assigned to the FOOT

CONTROLLER [1], and “Pedal Wah” is assigned to the

FOOT CONTROLLER [2].

You can assign functions to the foot controller from the

[SETTINGS] button → “Controllers” → “FC1 Assign”/

“FC2 Assign.” Refer to page 40 for a list of the parameters

that can be assigned.

INPUT [L/MONO]/[R] jacks/[GAIN] knob

These jacks allow you to connect an external audio

devices and mix the output of that device with that of this

instrument. Use the [GAIN] knob to adjust the volume

balance with this instrument.

OUTPUT [L]/[R] jacks

Use these two XLR-type jacks together to output

balanced audio signals.

OUTPUT [L/MONO]/[R] jacks

Use these two standard 1/4" mono audio jacks together

to output unbalanced stereo signals. When using mono

output, connect only to the [L/MONO] jack.

NOTE

• Select either jack or depending on the external audio

devices to be connected.

• In case both and jacks are connected to external audio

devices, the audio signals will be output from the both jacks

simultaneously.

[PHONES] jack

Use this standard 1/4" stereo audio jack to connect a pair

of headphones.

CAUTION

• To prevent hearing loss, avoid using headphones at high

volumes for extended periods of time.

• Whenever connecting other audio equipment, ensure that

all devices are turned off.

NOTE

The sound output via the headphones is identical to that output

via the OUTPUT [L]/[R] jacks and the OUTPUT [L/MONO]/[R]

jacks. Furthermore, plugging in or disconnecting a set of

headphones has no effect on the sound being output via these

jacks.

External MIDI keyboard, etc.

FC3A,

FC4A,

FC5

FC4A,

FC5

FC7

External

synthesizer, etc.

Mixer, etc.

Keyboard

amplifier

Monitor speakers

Headphones

CP88/CP73 Owner’s Manual

Power Supply

Connect the ends supplied AC power cord in the

following order. Make sure the [STANDBY/ON] switch

on the instrument is set to the STANDBY position.

1. Connect the supplied power cord to the [AC

IN] jack on the instrument’s rear panel.

2. Connect the other end of the power cord to an

AC outlet.

NOTE

Follow this procedure in reverse order when disconnecting the

power cord.

WARNING

• Use only the AC power cord supplied with your

instrument. The use of an inappropriate replacement can

lead to overheating or electric shock.

• The power cord supplied with your instrument must not

be used with other electrical equipment. Failure to

observe this precaution can result in damage to the

equipment or fire.

• Make sure your instrument the voltage requirement for

the country or region in which it is being used.

CAUTION

The instrument remains charged and draws a small amount

of power even when the [STANDBY/ON] switch is set to the

STANDBY position. If you intend not to use it for an

extended period of time, therefore, make sure to unplug the

power cord from the wall outlet.

Connecting Speakers or

Headphones

Since the instrument has no built-in speakers, you will

need to monitor the sound of the instrument by using

external equipment. Connect a set of headphones,

monitor speakers, or other playback equipment as

illustrated below. When making connections, be sure

that your cables have the appropriate ratings.

Turning On and Off

Make sure the volume settings of the instrument and

external devices such as powered speakers are turned to

the minimum before turning the power on. When

connecting the instrument to monitor speakers, turn on

the power switch of each device in the following order.

 Turning on

Turn the [MASTER VOLUME] knob of this instrument

to its minimum (le-most setting) → set the [STANDBY/

ON] switch to ON → turn the amplier or speaker power

on.

 Turning off

Turn the [MASTER VOLUME] knob of this instrument

to its minimum (le-most setting) → turn the amplier

or speaker power o → set the [STANDBY/ON] switch to

STANDBY.

Setting Up

[AC IN] jack

Power cord (included)

Rear panel

Keyboard amplifier or monitor speaker

(left) (right)

Headphones

OUTPUT

[L/MONO] jack

OUTPUT

[R] jack

[PHONES] jack

Sayfa yükleniyor...

Yamaha CP73 El kitabı

Marka: Yamaha

Modeli: CP73

Tip: El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

CP88

PDF''yi indir

rapor

diğer dillerde

español: Yamaha CP73 El manual del propietario
français: Yamaha CP73 Le manuel du propriétaire
italiano: Yamaha CP73 Manuale del proprietario
svenska: Yamaha CP73 Bruksanvisning
日本語: Yamaha CP73 取扱説明書
čeština: Yamaha CP73 Návod k obsluze
polski: Yamaha CP73 Instrukcja obsługi
Deutsch: Yamaha CP73 Bedienungsanleitung
português: Yamaha CP73 Manual do proprietário
English: Yamaha CP73 Owner's manual
dansk: Yamaha CP73 Brugervejledning
русский: Yamaha CP73 Инструкция по применению
suomi: Yamaha CP73 Omistajan opas
Nederlands: Yamaha CP73 de handleiding
română: Yamaha CP73 Manualul proprietarului

Yamaha CP73 El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha CP73 El kitabı

diğer dillerde

İlgili makaleler