Indesit EWSD 60852 W EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Fast daily cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
EWSD 60852
Instructions for use
WASHING MACHINE
English,1
GB
RO
PL
HU
TR
Magyar,37
SR
Română,25Polski,13
Türkçe,49 Cрпски,61
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machi-
ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him-
self/herself with its operation and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 3 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni-
ture cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the sup-
ply pipe by screwing
it to a cold water tab
using a ¾ gas threa-
ded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose exten-
sions; if it is absolutely necessary, the exten-
sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
•thesocketisearthedandcomplieswithall
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in
the Technical data table (see opposite);
•thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
•thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extreme-
ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must be within easy
reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
Technical data
Model
EWSD 60852
Dimensions
width 59.5 cm
height 85 cm
depth 42,4 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nection
maximum pressure 1 MPa
(10 bar)
minimum pressure 0.05
MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 800 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010
Programme 15:
Eco Cotton 6C.
Programme 15:
Eco Cotton 4C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2012/19/EU - WEEE
- 2006/95/EC Low Voltage)
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
• Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles
available and the remaining time of a cycle in progress;
iftheDELAYTIMERoptionhasbeenselected,the
countdown to the start of the selected cycle will appear.
DELAY TMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
WASH CYCLE
PROGRESS
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
DISPLAY
DELAY TIMER
button
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will flash and
only the second function will be activated; the indicator light
corresponding to the enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked to
prevent it from being opened; make sure the indicator light is
off before opening the door (wait approximately 3 minutes).
To open the door during a running wash cycle, press the
START/PAUSEbutton;thedoormaybeopenedoncethe
DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. SwitchthewashingmachineonbypressingtheON/OFFbutton.Allindicatorlightswillswitchonforafewseconds,then
theywillswitchoffandtheSTART/PAUSEindicatorlightwillpulse.
2. Load the laundry and close the door.
3.SettheWASHCYCLEknobtothedesiredprogramme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8.StartthewashcyclebypressingtheSTART/PAUSEbuttonandthecorrespondingindicatorlightwillremainlitinafixed
manner, in green.
Tocancelthesetwashcycle,pausethemachinebypressingtheSTART/PAUSEbuttonandselectanewcycle.
9.Attheendofthewashcyclethe END indicator light will switch on. The door can be opened once the DOOR LOCK
indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure
the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 15 with a temperature of 40°C.
3) Long programme for synthetics: set programme 4, then select the “
Extra Wash
” option.
* If you select programme 11 and exclude the spin cycle, the machine will drain only.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Pre-wash Wash
Fabric
softener
EVERYDAY FAST
1 Colour Mix 59’
40° 800 -
6 - - - 59’
2 Cotton 59’
60° 800 -
6 - - - 59’
3 Cotton 45’
40° 800 -
3 - - - 45’
4 Synthetics 59’ (3)
40°
(Max. 60°)
800 -
3 44 0,72 36 59’
5 Mix 30’
30° 800 -
3 71 0,16 27 30’
6 Express 20’
20° 800 -
1,5 - - - 20’
Special & Partial
7 Gym Kit
40° 600 -
2,5 - - - **
8 Sport Shoes
30° 600 -
Max. 1
pairs
- - - **
9
Baby: Heavily soiled delicate colours. 40° 800 -
2 - - - **
10 Rinse
- 800 - -
6 - - - **
11 Spin + Drain
- 800 - - - 6 - - - **
11 Only Drain *
-
- - - 6 - - - **
Dedicated
12
Duvet: for down-stuffed garments. 30° 800 -
1 - - - **
13
Wool: for wool, cashmere, etc. 40° 800 -
1 - - - **
14
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 -
1 - - - **
15
Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 800 -
6 71 0,94 50,0 240’
15
Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 800 -
6 71 0,80 66 220’
16
Cotton with prewash: extremely soiled whites. 90° 800
6 - - - **
Fast daily cycles
Acompletesetoffastprogrammestowashthemostcommonlyusedfabrics-evenwithafullload-andtoremovethemost
frequent daily dirt in less than 1 hour.
Colour Mix 59’: to wash mixed and coloured items together.
Cotton 59’: cycle designed to wash cotton garments - mainly white items. It can be used with powder detergent too.
Cotton 45’: short cycle designed to wash delicate cotton items.
Synthetics 59’: specific for synthetic items. If the dirt is difficult to remove, the temperature can be increased up to 60° and
powder detergent can be used too.
Mix 30’: short cycle designed to wash a mixed load of cotton and synthetic fabrics - white and coloured items together.
Express 20’: this programme refreshes your items, making them perfumed again in just 20 minutes.
GB
9
Setting the temperature
TurntheTEMPERATUREknobtosetthewashtemperature(seeTable of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
! Exception: if the 4 programme is selected, the temperature can be increased up to a value of 60°C.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 800 rpm
Synthetics 800 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected function is not compatible with another function which has been selected previously, the indicator light corre-
sponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding
to the enabled option will remain lit.
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period
has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option
press the button until the text “OFF” appears on the display.
Extra Wash
Enable the
Extra Wash
option for very dirty items, where compatible. Press this option to let the cycle automatically re-adjust
all wash parameters through a longer lasting cycle. The option always leaves the temperature unchanged, while the spin cycle
is automatically brought back to maximum levels. The user can set the spin cycle back to the desired value at any time.
The option washes cotton and synthetic items, saving energy and helping the environment. Energy saving is due to
a cold wash cycle, while an enhanced mechanical action and optimised water use make it possible to reach the desired result.
Recommended for slightly soiled garments. Use of liquid detergent recommended.
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the ma-
nufacturer’s instructions.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Gym Kit: cycle suitable to wash all sports items together,
including gym towels, while respecting their fibres (follow the
instructions in the garment labels).
Sport Shoes: is for washing sports shoes; for best results,
do not wash more than 1 pairs simultaneously.
We recommend fastening any strings before introducing the
shoes into the drum.
Baby: cycle designed for dirt typical of children’s garments
in that it effectively removes any traces of residual detergent.
Duvet: to wash single duvets (the weight of which should not
exceed 1 kg), cushions or clothes padded with goose down
such as puffa jackets, use the special wash cycle number 12.
We recommend that duvets are placed in the drum with their
edges folded inwards (see figure) and that no more than ¾
of the total volume of the drum is used. To achieve the best
results, we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.
Wool: all wool garments can be washed using programme 13,
even those carrying the “hand-wash only” label. For best re-
sults, use special detergents and do not exceed 1 kg of laundry.
Silk: use special wash cycle 14 to wash all silk garments.
We recommend the use of special detergent which has been
designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 14.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
GB
11
Troubleshooting
Yourwashingmachinecouldfailtowork.BeforecontactingtheTechnicalAssistanceCentre(see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The function indicator lights and
the start/pause indicator light flash,
while one of the phase in progress
indicator lights and the door locked
indicator light will remain lit in a fixed
manner.
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Personalisation”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
theapplianceoffandcontacttheAssistanceService.Ifthedwellingisononeof
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
Iftheproblempersists,contacttheTechnicalAssistanceService.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Alwaysrequesttheassistanceofauthorisedtechnicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
PL
Polski
Spis treści
Instalacja, 14-15
Rozpakowanie i wypoziomowanie
Podłączenia hydrauliczne i elektryczne
Pierwszy cykl prania
Dane techniczne
Utrzymanie i konserwacja, 16
Odłączenie wody i prądu elektrycznego
Czyszczenie pralki
Czyszczenie szuadki na środki piorące
Konserwacja okrągłych drzwiczek i bębna
Czyszczenie pompy
Kontrola przewodu doprowadzającego wodę
Zalecenia i środki ostrożności, 17
Ogólne zasady bezpieczeństwa
Utylizacja
Opis pralki i uruchamianie programu, 18-19
Panel sterowania
Kontrolki
Uruchamianie programu
Programy, 20
Tabela programów
Szybkie cykle codzienne
Personalizacja, 21
Ustawianie temperatury
Ustawianie wirowania
Funkcje
Środki piorące i bielizna, 22
Szuadka na środki piorące
Przygotowanie bielizny
Programy specjalne
System równoważenia ładunku
Nieprawidłowości w działaniu i sposoby ich
usuwania, 23
Serwis Techniczny, 24
PL
EWSD 60852
Instrukcja obsługi
PRALKA
14
PL
Instalacja
! Należy zachować niniejszą książeczkę, aby
móc z niej skorzystać w każdej chwili. W pr-
zypadku sprzedy, odspienia lub przeniesie-
nia pralki w inne miejsce należy zadbo prze-
kazanie instrukcji wraz z maszyną, aby nowy
aściciel mógł zapoznać s z działaniem
urządzenia i z dotyczącymi go ostrzeżeniami.
! Należy uważnie przeczyt instrukc obsługi:
zawiera ona ważne informacje dotyczące
instalacji oraz właściwego i bezpiecznego
użytkowania pralki.
Rozpakowanie i wypoziomowanie
Rozpakowanie
1. Rozpakować pralkę.
2. Sprawdzić, czy nie doznała ona uszkodzeń
w czasie transportu. W przypadku stwierdzenia
uszkodzeń nie podłączać jej i skontaktować się
ze sprzedawcą.
3. Odkręcić 3 śruby
z a b e z p i e c z a j ą c e
maszynę na czas
transportu oraz zdjąć
gumowy element z
podkład, znajducy
się w tylnej części
pralki (patrz rysunek).
4. Zatkać otwory przy pomocy plastikowych
zaślepek, znajdujących się w wyposażeniu maszyny.
5. Zachować wszystkie części: w razie
koniecznci przewiezienia pralki w inne miejsce,
powinny one zost ponownie zamontowane.
! Części opakowania nie zabawkami dla
dzieci.
Poziomowanie
1. Ustaw pralkę na płaskiej i twardej podłodze,
nie opierając jej o ściany, meble itp.
2. Jeśli pooga nie
jest idealnie pozioma,
naly skompensować
n i e r ó w n o ś c i ,
o d k r ę c a j ą c l u b
dokręcając przednie
nóżki (patrz rysunek);
kąt nachylenia, zmier-
zony na górnym blacie
pralki nie powinien
przekraczać 2°.
Staranne wypoziomowanie pralki zapewnia
jej stabilność i zapobiega wibracjom, hałasowi
oraz przesuwaniu się maszyny w czasie pracy.
W razie ustawienia na dywanie lub wykładzinie
dywanowej naly tak wyregulować nóżki,
aby pod pralką pozostawała wolna przestrzeń
niezbędna dla wentylacji.
Podłączenia hydrauliczne i elektryczne
Podłączenie przewodu doprowadzającego
wodę
1. Podłączyć przewód
z a s i l a j ą c y p o p r -
zez przykcenie do
zaworu wody zimnej z
końwką gwintowaną
¾ gas (patrz rysunek).
Przed poączeniem
spuszczać wodę do
momentu, aż stanie
się ona całkowicie pr-
zezroczysta.
2. Po d ł ą cz yć do
maszyny przewód
d o p r o w a d z a j ą c y
wodę, przykręcając
go do odpowiedniego
otworu dopływowego,
znajdującego się w
tylnej części pralki, z
prawej strony u góry
(patrz rysunek).
3. Zwrócić uwagę, aby na przewodzie nie było
zagięć ani zwężeń.
! Ciśnienie wody w kurku powinno mieścić się
w przedziale podanym w tabeli Danych tech-
nicznych (patrz strona obok).
! Jeśli długość przewodu doprowadzającego
wodę jest niewystarczająca, należy zwrócić się
do specjalistycznego sklepu lub do autoryzo-
wanego technika.
! Nigdy nie instalować już używanych przewo-
dów.
! Stosować przewody znajdujące się w
wyposażeniu maszyny.
15
PL
Podłączenie przewodu odpływowego
Podłączyć przewód
odpływowy, nie
zginając go, do rury
ściekowej lub do ot-
woru odpływowego w
ścianie, które powin-
ny znajdować się na
wysokości od 65 do
100 cm od podłogi;
ewentualnie oprzeć go
na brzegu zlewu lub
wanny, przymocowując
do kranu prowad-
nik, znajducy sw
wyposażeniu (patrz ry-
sunek). Wolny koniec pr-
zewodu odpływowego
nie powinien być zanur-
zony w wodzie.
! Odradza się stosowanie przewodów
przedłużających; jeśli to konieczne, przewód
przedłużający powinien mieć taką samą
średnicę jak oryginalny, a jego długość nie
może przekraczać 150 cm.
Podłączenie elektryczne
Przed włożeniem wtyczki do gniazdka elekt-
rycznego należy się upewnić, czy:
gniazdko posiada uziemienie i jest zgodne
z obowiązującymi przepisami;
gniazdko jest w stanie wytrzymmaksy-
malne obciążenie mocy maszyny, wskazane
w tabeli Danych technicznych (patrz obok);
napięcie zasilania mieści się w wartościach
wskazanych w tabeli Danych technicznych
(patrz obok);
gniazdko pasuje do wtyczki pralki. W prze-
ciwnym razie należy wymienić gniazdko lub
wtyczkę.
! Nie należy instalować pralki na otwartym
powietrzu, nawet w osłoniętym miejscu, gdyż
wystawienie urządzenia na działanie deszc-
zu i burz jest bardzo niebezpieczne.
! Po zainstalowaniu pralki gniazdko elektry-
czne powinno być łatwo dostępne.
! Nie używać przedłużaczy ani ozgałęźników.
! Przewód nie powinien być pozginany ani
przygnieciony.
! Przewód zasilania elektrycznego może być
wymieniany wyłącznie przez autoryzowanych
techników.
Uwaga! Producent nie ponosi żadnej
odpowiedzialności w przypadku nieprzestrze-
gania powyższych zasad.
Pierwszy cykl prania
Po zainstalowaniu pralki, przed przystąpieniem
do jej użytkowania, należy wykonać jeden cykl
prania ze środkiem piorącym, ale bez wsadu,
nastawiając program 2.
Dane techniczne
Model EWSD 60852
Wymiary
szerokość cm 59,5
wysokość cm 85
głębokość cm 42,4
Pojemność od 1 do 6 kg
Dane prądu
elektrycznego
dane techniczne umieszc-
zone są na tabliczce na
maszynie
Dane sieci
wodociągowej
Maksymalne cnienie
1 MPa (10 baw)
ciśnienie minimalne
0,05 MPa (0,5 barów)
pojemność bębna 40 litrów
Szybkość
wirowania
do 800 obrotów na minutę
Programy te-
stowe zgodnie
z regulamin
1061/2010 i
1015/2010
Program 15: Eco Bawełna
60°C;
Program 15: Eco Bawełna
40°C.
Urządzenie to zostało
wyprodukowane zgodnie z
następującymi przepisami
EWG:
- 2004/108/CE (o
Kompatybilności Elektro-
magnetycznej)
- 2012/19/EU - WEEE
- 2006/95/CE (o Niskim
Napięciu)
65 - 100 cm
16
PL
Utrzymanie i konserwacja
Odłączenie wody i prądu elektrycz-
nego
Zamknąć kurek dopływu wody po każdym
praniu. W ten sposób zmniejsza się zużycie
instalacji hydraulicznej pralki oraz eliminuje
się niebezpieczeństwo wycieków.
Przed przystąpieniem do czyszczenia pralki
oraz do czynności konserwacyjnych wyjąć
wtyczkę z gniazdka.
Czyszczenie pralki
Obudowę zewnętrzną i gumowe części pralki
można myć ściereczką zmoczoną w letniej wo-
dzie z mydłem. Nie stosow rozpuszczalników
ani ściernych środków czyszczących.
Czyszczenie szufladki na środki
piorące
Wysunąć szufladkę,
unosząc ją lekko ku
górze i wyciągając na
zewnątrz (patrz rysu-
nek).
Wypłukać szufladkę
pod bieżącą wodą.
Czynność tę należy
wykonywać stosun-
kowo często.
Konserwacja okrągłych drzwiczek i
bębna
Drzwiczki pralki należy zawsze pozostawiać
uchylone, aby zapobiec tworzeniu się niepr-
zyjemnych zapachów.
Czyszczenie pompy
Pr a lk a w yp o sa ż on a je s t w po mp ę
samoczyszczącą, która nie wymaga zabiegów
konserwacyjnych. Może się jednak zdarzyć, że
drobne przedmioty (monety, guziki) wpadną
do komory wstępnej zabezpieczającej pompę,
która znajduje się w jej dolnej części.
! Należy s upewnić, że cykl prania został
zakończony i wyjąć wtyczkę z gniazdka.
Aby dostać się do komory wstępnej:
1. zdjąć panel pok-
rywy z przedniej stro-
ny pralki przy pomocy
śrubokrętu (patrz ry-
sunek);
2. odkręcić pokrywę,
obracając ją w kie-
runku przeciwnym
do ruchu wskazówek
zegara (patrz rysu-
nek): wypłynięcie
niewielkiej ilości
wody jest normalnym
zjawiskiem;
3. dokładnie wyczyścić wnętrze;
4. ponownie przykręcić pokrywę;
5. ponownie założyć panel upewniwszy się,
przed dociśnięciem go do maszyny, czy za-
trzaski zostały umieszczone w odpowiednich
otworach.
Kontrola przewodu
doprowadzającego wodę
Przynajmniej raz w roku należy sprawdzić
przewód doprowadzający wodę. Jeśli wido-
czne są na nim pęknięcia i rysy, należy go
wymienić: w trakcie prania duże ciśnienie
może bowiem spowodować jego nagłe rozer-
wanie.
! Nigdy nie instalować już używanych pr-
zewodów.
17
PL
! Pralka została zaprojektowana i wyprodukowana zgodnie
z międzynarodowymi normami bezpieczeństwa. Niniej-
sze ostrzeżenia zostały tu zamieszczone ze względów
bezpieczeństwa i należy je uważnie przeczytać.
Ogólne zasady bezpieczeństwa
• Urządzenie to zostało zaprojektowane wyłącznie do
ytkowania w warunkach domowych.
Z niniejszego urządzenia mogą korzyst
dzieci powyżej 8 roku życia i osoby o
ograniczonych zdolnościach fizycznych,
zmysłowych bądź umysłowych, jak również
osoby nieposiadace doświadczenia lub
znajomości urządzenia, jeśli znajdują się one
pod nadzorem innych osób lub jeśli zostały
pouczone na temat bezpiecznego sposobu
użycia urządzenia oraz zdają sobie sprawę
ze związanych z nim zagrożeń. Dzieci nie
powinny bawić się urządzeniem. Prace
związane z czyszczeniem i konserwacją nie
mogą być wykonywane przez dzieci, jeśli nie
są one nadzorowane.
• Pralki powinny ywać wyłącznie osoby dorosłe i w sposób
zgodny z instrukcjami podanymi w niniejszej książeczce.
• Nie dotykać pralki, stojąc przy niej boso lub mając mokre
lub wilgotne ręce albo stopy.
• Nie wyjmować wtyczki z gniazdka, ciągnąc za kabel, lecz
trzymając za wtyczkę.
W trakcie pracy maszyny nie otwierać szuadki na środki piorące.
• Nie dotykać odprowadzanej wody, gd może ona
osiągać wysokie temperatury.
W żadnym wypadku nie otwierać okrągłych drzwiczek pralki na
siłę: grozi to uszkodzeniem mechanizmu zabezpieczającego
drzwiczki przed przypadkowym otwarciem.
• W razie wystąpienia usterki nie należy w żadnym wypad-
ku próbować dostać się do wewnętrznych części pralki z
zamiarem samodzielnego dokonania naprawy.
Zawsze uważać, aby dzieci nie zbliżały s do pracującej pralki.
W czasie prania okrągłe drzwiczki pralki nagrzewają się.
• Jeśli trzeba przenieść pralkę w inne miejsce, należy to robić
bardzo ostrożnie, w dwie lub trzy osoby. Nigdy nie przenosić
pralki samodzielnie, gdyż jest ona bardzo cżka.
• Przed włożeniem bielizny sprawdzić, czy ben jest pusty.
Utylizacja
• Utylizacja opakowania: stosować się do lokalnych przepi-
w, dzki temu opakowanie będzie mogło zostać ponow-
nie wykorzystane.
• Europejska Dyrektywa 2012/19/EU WEEE dotycząca
Zużytych Elektrycznych i Elektronicznych Urządzeń zaada
zakaz pozbywania się starych urządzeń domowego ytku
jako nieposortowanych śmieci komunalnych. Zużyte
urządzenia mus być osobno zbierane i sortowane w celu
zoptymalizowania odzyskania oraz ponownego przetwor-
zenia pewnych komponenw i materiów.
Pozwala to ograniczyć zanieczyszczenie środowiska i
pozytywnie wpływa na ludzkie zdrowie. Przekreślony
symbol „kosza” umieszczony na produkcie przypomina
klientowi o obowiązku specjalnego sortowania.
Konsumenci powinni kontaktować się z adzami lokalnymi
lub sprzedawcą w celu uzyskania informacji dotyccych
pospowania z ich zużytymi urdzeniami gospodarstwa
domowego.
Zalecenia i środki
ostrożności
18
PL
Szuadka na środki piorące: do dozowania środków
piorących i dodatków (patrz „Środki piorące i bielizna”).
Przycisk ON/OFF: do włączania i wyłączania pralki.
Pokrętło PROGRAMÓW: do ustawiania programów. W
czasie trwania programu pokrętło pozostaje nieruchome.
Przyciski z kontrolkami FUNKCJI: do wyboru dostępnych
funkcji. Kontrolka wybranej funkcji pozostaje zaświecona.
Pokrętło WIROWANIA: do nastawienia lub wyłączenia
wirowania (patrz “Personalizacja”).
Pokrętło TEMPERATURY: do regulacji temperatury
prania lub do nastawienia prania w zimnej wodzie (patrz
„Personalizacja”).
WYŚWIETLACZ: aby wyświetlić czas trwania poszc-
zególnych dostępnych programów i po starcie, czas, jaki
pozostał do zakończenia programu; w przypadku, gdy
została ustawiona funkcja URUCHOMIENIE OPÓZNIO-
NE, wyświetlony zostanie pozostały czas od momentu
startu wybranego programu.
Przycisk URUCHOMIENIE OPÓZNIONE : nacisnąc w
celu ustawienia opóźnionego uruchomienia wybranego
programu. Opóźnienie wyświetlone zostanie na ekranie.
Kontrolki STANU ZAAWANSOWANIA CYKLU:
umożliwiają kontrolę stanu zaawansowania programu
prania.
Zapalona kontrolka wskazuje bieżącą fazę.
Kontrolka BLOKADY OKRĄGŁYCH DRZWICZEK:
pozwala sprawdzić czy możliwe jest otwarcie okrągłych
drzwiczek (patrz strona obok).
Przycisk z kontrolką START/PAUSE: do uruchamiania
programów lub ich chwilowego przerywania.
N.B.: aby przerwać wykonywane pranie, należy nacisnąć
ten przycisk, jego kontrolka zacznie pulsować na
pomarańczowo, natomiast kontrolka bieżącej fazy będzie
świecić ciągłym światłem. Jeśli kontrolka BLOKADY
OKRĄGŁYCH DRZWICZEK jest wyłączona, można
otworzyć drzwiczki pralki (odczekać około 3 minuty).
W celu ponownego uruchomienia prania od momen-
tu, w którym zostało ono przerwane, należy ponownie
nacisnąć ten przycisk.
Funkcja stand by
Pralka ta, w myśl nowych norm europejskich związanych
z oszczędnością elektryczną, posiada system auto
wyłączenia (stand by), który włącza się po 30 minutach
nie użytkowania. Ponownie lekko wcisnąć przycisk ON/
OFF i poczekać, aż pralka ponownie włączy się.
Opis pralki i uruchamianie
programu
Kontrolki
STANU
ZAAWANSOWANIA CYKLU
Kontrolka
BLOKADY OKRĄGŁYCH
DRZWICZEK
Przycisk z
kontrolką
START/PAUSE
Panel sterowania
Szuadka na środki piorące
Pokrętło
PROGRAMÓW
Przycisk ON/OFF
Pokrętło
TEMPERATURY
Pokrętło
WIROWANIA
Przyciski z
kontrolkami
FUNKCJI
WYŚWIETLACZ
URUCHOMIENIE
OPÓZNIONE
19
PL
Kontrolki
Kontrolki dostarczają ważnych informacji.
Oto co sygnalizują:
Kontrolki bieżącej fazy prania:
Po wybraniu i uruchomieniu żądanego cyklu prania kon-
trolki będą się kolejno zapalać, wskazując stan zaawan-
sowania programu:
Przyciski funkcyjne i ich kontrolki
Po dokonaniu wyboru funkcji jej kontrolka zaświeci się.
W przypadku wyboru funkcji niezgodnej z ustawionym
programem jej kontrolka zacznie pulsować i funkcja nie
włączy się.
Jeśli wybrana funkcja nie jest zgodna z inną, ustawioną
uprzednio, kontrolka odpowiadająca pierwszej funkcji
będzie pulsowała i uruchomiona zostanie jedynie druga
funkcja a kontrolka uruchomionej funkcji zaświeci się.
Kontrolka blokady okrągłych drzwiczek
Włączona kontrolka wskazuje, że drzwiczki zostały
zablokowane w celu uniemożliwienia ich otwarcia; aby
można było otworzyć drzwiczki, kontrolka musi być
wyłączona; (odczekać około 3 minuty). Aby otworzyć
drzwiczki w trakcie wykonywania cyklu należy nacisnąć
przycisk START/PAUSE; jeśli kontrolka BLOKADY
OKRĄGŁYCH DRZWICZEK jest wyłączona, można
otworzyć drzwiczki.
Uruchamianie programu
1. Włączyć pralkę, naciskając przycisk ON/OFF. Wszystkie kontrolki zapalą się na kilka sekund, następnie wyłączą się i
zacznie pulsować kontrolka START/PAUSE.
2. Załadować bieliznę i zamknąć drzwiczki pralki.
3. Ustawić żądany program przy pomocy pokrętła PROGRAMÓW.
4. Ustawić temperaturę prania (patrz „Personalizacja”).
5. Ustawić szybkość wirowania (patrz „Personalizacja”).
6. Wsypać środek piorący i dodatki (patrz „Środki piorące i bielizna”).
7. Wybrać żądane funkcje.
8. Uruchomić program naciskając przycisk START/PAUSE, kontrolka programu będzie świecić ciągłym światłem w kolor-
ze zielonym. Aby anulować ustawiony cykl, należy chwilowo zatrzymać urządzenie, naciskając przycisk START/PAUSE, i
wybrać nowy cykl.
9. Po zakończeniu programu zapali się kontrolka . Po zgaśnięciu kontrolki BLOKADY OKRĄGŁYCH DRZWICZEK
można otworzyć drzwiczki (odczekać około 3 minuty). Wyjąć bieliznę i pozostawić drzwiczki pralki uchylone, aby bęben
mógł wyschnąć.
Wyłączyć pralkę, naciskając przycisk ON/OFF.
Pranie
Płukanie
Wirowanie
Wydalanie wody
Koniec prania
20
PL
Programy
Tabela programów
1) Program kontrolny zgodny z regulamin 1061/2010: ustawić program 15, wybierając temperaturę 60°C.
Ten cykl jest odpowiedni do prania średnio zabrudzonej odzieży bawełnianej i jest najbardziej wydajnym cyklem pod względem łącznego zużycia energii
elektrycznej i wody; należy go używać do odzieży przeznaczonej do prania w 60°C. Rzeczywista temperatura prania może się różnić od podanej.
2) Program kontrolny zgodny z regulamin 1061/2010: ustawić program 15, wybierając temperaturę 40°C.
Ten cykl jest odpowiedni do prania średnio zabrudzonej odzieży bawełnianej i jest najbardziej wydajnym cyklem pod względem łącznego zużycia energii
elektrycznej i wody; należy go używać do odzieży przeznaczonej do prania w 40°C. Rzeczywista temperatura prania może się różnić od podanej.
Dla wszystkich Instytucji homologacyjnych:
2) Program bawełna, długi: ustawić program 15, wybierając temperaturę 40°C.
3) Program do tkanin syntetycznych długi: ustawić program 4, a następnie wybrać opcję
Extra Wash
.
Czas trwania cyklu wskazany na wyświetlaczu lub w instrukcji jest czasem oszacowanym dla standardowych warunków. Rzeczywisty czas trwania cyklu może się zmieniać w zależności od wielu
czynników, takich jak temperatura i ciśnienie wody na wlocie, temperatura otoczenia, ilość detergentu, ilość i rodzaj pranej odzieży, wyważenie ładunku, wybrane opcje dodatkowe.
* Po wybraniu programu 11 i wyłączeniu wirowania maszyna wykona jedynie opróżnianie z wody.
** Możliwa jest kontrola czasu trwania programów na wyświetlaczu.
Programy
Opis programu
Temp.
max (°C)
Prędkć
max
(obrow na
minutę)
Środki piorące
Ładunek
max (kg)
Wilgotność
resztkowa %
Zużycie ener-
gii kWh
Woda łącznie
lt
Czas trwania
cyklu
Pranie
Wstępne
Pranie
Wybie-
lacz
EVERYDAY FAST
1
Mix Kolorowe 59’
40° 800 -
6 - - - 59’
2
Bawełna 59’
60° 800 -
6 - - - 59’
3
Bawełna 45’
40° 800 -
3 - - - 45’
4
Tkaniny syntetyczne 59’ (3)
40°
(Max. 60°)
800 -
3 44 0,72 36 59’
5
Mix 30’
30° 800 -
3 71 0,16 27 30’
6
Express 20’
20° 800 -
1,5 - - - 20’
Special & Partial
7
Odzież sportowa
40° 600 -
2,5 - - - **
8
Obuwie sportowe
30° 600 -
Maks.
1
pary.
- - - **
9
Baby
40° 800 -
2 - - - **
10
Płukanie
- 800 - -
6 - - - **
11
Wirowanie + Wydalanie wody
- 800 - - - 6 - - - **
11
Tylko Odprowadzanie wody *
- - - - 6 - - - **
Dedicated
12
Pościel: do odzieży ocieplanej gęsim puchem.
30° 800 -
1 - - - **
13
Wełna: do wełny, kaszmiru, itp.
40° 800 -
1 - - - **
14
Jedwab/Firanki
: do jedwabiu, wiskozy, bielizny.
30° 0 -
1 - - - **
15
Eco Bawełna 60°C (1): tkaniny białe i kolorowe, wytrzymałe,
mocno zabrudzone.
60° 800 -
6 71 0,94 50,0 240’
15
Eco Bawełna 40°C (2): tkaniny białe i kolorowe, delikatne, lek-
ko zabrudzone.
40° 800 -
6 71 0,80 66 220’
16
Bawełna z praniem
Wstępnym
: bielizna biała silnie zabrudzona.
90° 800
6 - - - **
Szybkie cykle codzienne
Pełny zestaw szybkich cykli do prania również przy pełnym wsadzie najpopularniejszych rodzajów tkanin i usuwania
najczęstszych rodzajów codziennych zabrudzeń w czasie krótszym niż 1 godzina.
Mix Kolorowe 59’: do prania razem tkanin mieszanych i kolorowych.
Bawełna 59’: cykl opracowany do prania tkanin bawełnianych, głównie białych. Można w nim stosować również detergent
w proszku.
Bawełna 45’: krótki cykl opracowany do prania delikatnych tkanin bawełnianych
Tkaniny syntetyczne 59’: przeznaczony do prania odzieży syntetycznej. W przypadku bardziej uporczywych zabrudzeń
można zwiększyć temperaturę do 60° i użyć także detergentu w proszku.
Mix 30’: krótki cykl opracowany do prania razem białych i kolorowych tkanin bawełnianych i syntetycznych.
Express 20’: program, który odświeża odzież czyniąc ją znów pachnącą w zaledwie 20 minut/.
1 / 1

Indesit EWSD 60852 W EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi