Whirlpool LSF 712 EUHA Kullanici rehberi

Marka: Whirlpool

Model: LSF 712 EUHA

Kategori: Bulaşık makineleri

Tip: Kullanici rehberi

Operating instructions

Contents

Installation, 2-3

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Ecodesign Regulation

Description of the appliance, 4

Overall view

Control panel

Loading the racks, 5

Lower rack

Cutlery basket

Upper rack

Start-up and use, 6-7

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 8

Table of wash cycles

Rinse aid and refined salt, 9

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 10

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Precautions, advice and Assistance, 11

General safety

Disposal

Saving energy and respecting the environment

Assistance

Troubleshooting, 12

LSF 712

DISHWASHER

English,1

Español, 13

Polski, 25

Hrvatski, 37

Ελληνικά, 49

Türkçe, 61

Українська, 73

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved,

please ensure the manual is kept with the machine, so that

the new owner may benefit from the advice contained within

it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in

an upright position; if absolutely necessary, it may be tilted

onto its back.

This appliance is intended to be used in household and

similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check that

it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with

the wall. This appliance can also be recessed under a single

worktop

(see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the appliance

is levelled correctly, it will be more stable and much less likely

to move or cause vibrations and noise while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance

* on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an anticlockwise

direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should

only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity supply

cable may be positioned towards the right or the left in order

to achieve the best possible installation.

Connecting the water inlet hose

• Toasuitablecoldwaterconnectionpoint:beforeattaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded connection.

• Toasuitablehotwaterconnectionpoint:yourdishwasher

may be supplied with hot water from the mains supply (if

you have a central heating system with radiators) provided

that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to

a cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician

(see Assistance).

The water pressure must be within the values indicated in

the Technical data table

(see adjacent information).

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to 80

cm from the floor / surface where the dishwasher rests (A).

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop

*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut

as it contains live electrical parts.

* Only available in selected models.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• The socket is earthed and complies with current

regulations.

• The socket can withstand the maximum load of the

appliance, which is indicated on the data plate located

on the inside of the door

(see chapter entitled Description

of the appliance).

• Thepowersupplyvoltagefallswithinthevaluesindicated

on the data plate on the inside of the door.

• Thesocketiscompatiblewiththeplugoftheappliance.

If this is not the case, ask an authorised technician to

replace the plug

(see Assistance)

; do not use extension

cables or multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order

to protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add only then approximately 1 kg of salt

(see chapter entitled Rinse aid and refined salt)

. The water

may overflow: this is normal and is not a cause for concern.

Select the water hardness value

(see chapter entitled Rinse

aid and refined salt).

- After the salt has been poured into

the machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener and

the heating element may be damaged as a result.

Technical data

Dimensions

width 45 cm

height 85 cm

depth 60 cm

Capacity 10 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 psi – 145 psi

Power supply voltage See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/ CE Waste Electrical

and Electronic Equipment (WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a nor-

mal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption

even further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

Standard conditions* User conditions**

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration (min/

cycle)

INTENSIVE

1,30 14 150 1,15 14 140

NORMAL

1,05 14 115 0,95 13 110

Overall view

Description of the

appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel***

***

Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

Low Salt

indicator light

End and 9h. Delayed

start indicator light

Start/Pause button

and indicator light

Half load button

and indicator light

Delayed start button

Select wash cycle knob

Washing and 3h. Delayed

start indicator light

Drying and 6h.Delayed

start indicator light

ON/OFF/RESET button

Loading the racks

*Only available in selected models. ** The number and

position may vary.

Before loading the racks, remove all food residues from

the crockery and empty liquids from glasses and cups.

Arrange the crockery so that it is held in place firmly and

does not tip over.

After loading the appliance, check that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, plates, salad bowls, cutlery,

etc. as seen in the

Loading examples.

Plates and large covers should be placed at the sides of

the rack, ensuring that they do not block the rotation of the

upper sprayer arm.

Some dishwasher models are fitted

with tip-up sections

*, which can

be used in a vertical position when

arranging plates or in a horizontal

position when arranging pans and

salad bowls.

Cutlery basket

The type of cutlery basket may vary according to the dishwasher

model: The cutlery basket should be positioned at the front of

the lower rack, by sliding it between the fixed inserts, or on the

upper rack when the half load option has been selected (in

models featuring this option).

- It has a collapsible sli-

ding system which means

the cutlery can be arran-

ged in the best possible

way.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards, or they

must be positioned horizontally in the tip-up compartments on

the upper rack.

Cutlery basket positioning examples

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

tea and coffee cups, saucers, small salad bowls, saucepans and

small saucepans which are not too soiled, using the

examples

as a guide.

•Mugsandcups,longsharpknivesandservingutensils:place

these on the tip-up compartments**.

Tip-up compartments with adjustable tilt*

- The tilt feature can be used to increase the space in the upper

rack, to position wine glasses with different stem lengths safely

and to improve drying performance.

-Lift the tip-up compartment, slide it gently and position it in the

desired tilt angle.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper

rack may be moved to a higher or lower level.

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

Never lift or lower the rack on one side only.

Open the left and right guide rail stops

and pull out the rack; position it higher

or lower as required, slide it along the

guide rails until the front wheels are in

place and close the stops

(see figure).

If the rack is fitted with “Dual Space”

handles

(see figure)

, pull out the upper

rack until it reaches its stop point, grip

the handles at the sides of the rack and

move it upwards or downwards, then

slowly let it fall back into place.

Loading examples for the upper rack

Loading examples for the lower rack

Items which should not be washed in the dishwasher

• Woodenitems,objectswithwoodenorhornhandlesorglued-

on parts.

• Itemsmadefromaluminium,copper,brass,pewterortin.

• Itemsmadefromplasticmaterialwhichisnotheat-resistant.

• Antiqueorhand-paintedporcelain.

• Antique silver. Silverwhichis not antique may, however,

be washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other metals.

We recommend the use of crockery which is dishwasher

safe.

Tilt A Tilt B Tilt C

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct amount

of detergent being used; exceeding the stated amount

does not result in a more effective wash and increases

environmental pollution.

Only use detergent which has been specifically

designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle has

ended.

The use of tablets is only recommended for models

which offer the MULTI-FUNCTIONAL TABLETS option.

To achieve the best results from each washing and

drying cycle, powder detergent, rinse aid liquid and salt

should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing

button D.

2. Pour in the detergent after

consulting the

Table of wash

cycles:

• For powder detergent use

compartments A and B.

•Fordetergentintabletform:when

the cycle requires 1 tablet, place

it in compartment A and close the cover; when it requires

2, place the second tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

* Only available in selected models.

Starting the dishwasher

1. Turn the water tap on.

2.PresstheON/OFFbutton:alltheindicatorlightsonthe

control panel will light up for a few seconds.

3. Open the door and pour in a suitable amount of detergent

(see below).

4. Load the racks

(see Loading the racks)

and shut the door.

5. Select the wash cycle by turning the WASH CYCLE

SELECT knob in a clockwise direction: align the notch on the

knob with the number or symbol representing the desired

wash cycle. The START/PAUSE indicator light will flash.

6. Select the wash options

(see adjacent information).

7. Start the cycle by pressing the START button; the indicator

light will light up and remain lit in a fixed manner. The

indicator light corresponding to the wash phase will switch

on, signalling that the wash cycle has begun.

8. At the end of the wash cycle the END indicator light will

switch on (fixed light). Switch off the appliance by pressing

theON/OFFbutton,shutoffthewatervalveandunplugthe

appliance from the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

- The machine will switch off automatically during

certain periods of inactivity, in order to minimise

electricity consumption.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it

has only just begun: once the wash cycle has started, switch

offthemachinebypressingandholdingtheON/OFF/Reset

button. Switch it back on using the same button and select

the desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding indicator

light will flash). Open the door, taking care to avoid

the escaping steam, and place the crockery inside the

appliance. Press the Start/Pause button (fixed light): the cycle

starts from the point at which it was interrupted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start* function

(if selected) is interrupted.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

* Only available in selected models.

Half load

If there are not many dishes to be washed, a half load cycle

may be used in order to save water, electricity and detergent.

SelectthewashcycleandpresstheHALFLOADbutton:the

indicator light will illuminate.

Remember to halve the amount of detergent.

It is better to use powder detergent in this case.

Delayed start

It is possible to delay the start time of the wash cycle by 3, 6

or 9 hours.

After selecting the desired wash cycle and any other options,

select Delayed Start by pressing the Delayed Start button re-

peatedly; the washing (3 hours), drying (6 hours) and end (9

hours) indicator lights will flash in succession.

If the Delayed Start button is pressed again, the option is de-

selected.

After the selection process, the countdown will begin if the Start/

Pause button is pressed. The selected delay period indicator

light flashes and the Start/Pause button stops flashing (fixed

light).

When the time has elapsed, the indicator light corresponding

to the selected delay period stops flashing (fixed light) and the

wash cycle begins.

The Delayed Start function cannot be set once the wash

has already started.

Wash options*

The OPTIONS may only be set, modified or reset after

the wash cycle has been selected and before the Start/

Pause button has been pressed.

Only the options which are compatible with the type of wash

cycle set may be selected. If an option is not compatible

with the selected was cycle

(see Table of wash cycles),

the

corresponding LED flashes rapidly 3 times.

If an option is selected which is incompatible with another

option or wash cycle selected previously, the incompatible

option light will flash 3 times and switches off, while the most

recently selected setting remains lit.

To deselect an option which has been set by mistake, press

the corresponding button again.

Wash cycles

If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,

reduce the amount of detergent used accordingly.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Notes:

Optimum performance levels when using the “Daily 60’ - Rapid wash” cycles can be achieved by observing the maximum amounts

of crockery specified.

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less

energy and is les harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following

address: [email protected]

Wash cycle selection

instructions

Wash cycle

Detergent

(A) = compartment A

(B) = compartment B

Wash cycles

which include

drying

Options

Wash cycle

duration

(tolerance ±10%)

Hrs. Min.

Powder Liquid Tablets

Heavily soiled dishes and pans

(not to be used for delicate

items).

1.Intensive

25 g (A) 25 ml (A) 1 (A) Yes

Delayed Start

- Half Load

2:25’

Normally soiled pans and dishes.

Standard daily wash cycle.

2. Normal

21 g (A)

4 g (B)

21 ml (A)

4 ml (B)

1 (A) Yes

Delayed Start

- Half Load

1:50’

Limited quantity of daily soiling.

(4 place settings + 1 saucepan

+1 frying pan).

3. Daily 60’

25 g (A) 25 ml (A) 1 (A) No

Delayed Start

- Half Load

1:00’

Pre-wash for dishes while

awaiting completion of the load

with the dishes from the next

meal.

4. Soak

No No No No

Delayed Start

- Half Load

0:08’

Environmentally-friendly

wash cycle with low energy

consumption levels, suitable for

pans and dishes.

5. Eco

21 g (A)

4 g (B)

21 ml (A)

4 ml (B)

1 (A) Yes

Delayed Start

- Half Load

3:00’

Economic and fast wash to be

used for lightly soiled dishes.

(Run cycle immediately after

use) (2 plates + 2 glasses + 4

pieces of cutlery + 1 saucepan +

1 small frying pan).

6. Rapid

21 g (A) 21 ml (A) 1 (A) No Delayed Start 0:35’

Economic and fast wash for

delicate items which are sensitive

to high temperatures. (Run cycle

immediately after use) (glasses

upper rack + delicate plates

lower rack).

7. Crystal

25 g (A) 25 g (A) 1 (A) Yes

Delayed Start

- Half Load

1:35’

Rinse aid and refined salt

Only use products which have been specifically

designed for dishwashers.

Do not use table salt or industrial salt, or washing

up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

Followtheinstructionsgivenonthepackaging.

If you do not add salt or rinse aid, the LOW SALT*

and LOW RINSE AID

* indicator lights remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs

off surfaces more readily and therefore does not leave streaks

or marks.

The rinse aid dispenser should be filled:

•WhentheLOWRINSEAID* indicator light on the control

panel/dislay is illuminated;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from

the dispenser. If this happens,

clean the spill immediately with

a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver to

turnthedosageadjuster(F)tooneofthe6pre-setpositions

(the default position is set to 4):

•Iftherearestreaksonthecrockery,settheadjustmentdevice

to a lower number (1-3).

•Ifdropsofwaterremainonthecrockeryoriftherearelimescale

marks present after the cycle has finished, set the adjuster to

a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

- Switch the machine off using the ON/OFF button and open

the door.

- Set the SELECT WASH CYCLE knob first to wash cycle 5,

then to wash cycle 1, then to wash cycle 5 again.

- Press the ON/OFF button; the wash cycle phase (washing,

drying, end) indicator lights will flash. It is now possible to select

the water hardness level. There is a water hardness level for

every wash cycle:

E.g.: wash cycle 1, water hardness level 1

wash cycle 2, water hardness level 2, etc. etc., up to a maximum

of 5

* levels.

(The default water softener setting is level 3).

- To exit the function, wait a few seconds or press one of the op-

tion buttons

*, or switch off the machine using the ON/OFF button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f = hardness

measuredinFrenchdegrees-mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty. Refined salt

removes limescale from the water, thus avoiding the formation

of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

•Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser.

• When the LOW SALT* indicator light on the control panel/

display is illuminated;

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel*

(see figure)

and fill

the salt container right up to its edge (this

should hold approximately 1 kg); it is not unusual for a little

water to leak out.

4. Remove the funnel* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it

on, the head facing downwards so as to let the water flow out of

the four cracks which are arranged in a star shape on the lower

part of the cap. (Salt cap with green float

It is advisable to perform this procedure every time you add

salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt container

capacity duration**

Level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt

. * this setting may cause a slight increase in the

duration of the cycles. ** for 1 wash cycle per day.

Care and maintenance

Shutting off the water and electricity

supplies

• Turn



off

 the

water

 tap

after



every



wash



cycle



avoid



leaks.

• Always



unplug



the

appliance

when

cleaning



and

when

performing maintenance work.

Cleaning the dishwasher

• The



external

surfaces



the



machine



and



the



control



panel may be cleaned using a non-abrasive cloth which

has been dampened with water. Do not use solvents or

abrasive products.

• Any



marks



the

inside



the



appliance



may



removed



using a cloth dampened with water and a little vinegar.

Preventing unpleasant odours

• Always



keep



the

door



the



appliance



ajar



order



avoid moisture from forming and being trapped inside

the machine.

• Clean



the



seals

around

the



door



and



detergent



dispensers

regularly using a damp sponge. This will avoid food

becoming trapped in the seals, which is the main cause

behind the formation of unpleasant odours.

Cleaning the sprayer arms

Food



residue

may

become



encrusted

ontothe

sprayer

arms



and block the holes used to spray the water. It is therefore

recommended that the arms are checked from time to time

and cleaned with a small non-metallic brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in an

anti-clockwise direction.

The upper sprayer arm should

be replaced with the holes facing

upwards.

The lower sprayer arm can be

removed by pulling it upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it is

clear and free of impurities before performing the necessary

connections. If this precaution is not taken, the water inlet

could become blocked and damage the dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter

and clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove

food residues from the washing water and then recirculate

the water. They should be cleaned if you wish to achieve the

best results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if

the filter is loose.

• After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using

a non-metallic brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2. Remove the cup filter B by exerting a slight pressure on

the side flaps (fig. 2).

3. Slide out the stainless steel plate filter A (fig. 3).

4. Inspect the trap and remove any food residue. NEVER

REMOVE the wash cycle pump

(black detail) (fig. 4).

After cleaning the filters, replace the filter assembly and fix

it in position correctly; this is essential for maintaining the

efficient operation of the dishwasher.

Leaving the machine unused for extended

periods

• Disconnecttheappliancefromtheelectricitysupplyand

shut off the water tap.

• Leavethedooroftheapplianceajar.

•Whenyoureturn,runawashcyclewhenthedishwasher

is empty.

* Only available in selected models.

Precautions, advice and

Assistance

This appliance was designed and manufactured in

compliance with current international safety standards. The

following information has been provided for safety reasons and

should therefore be read carefully.

General safety

•Thisapplianceisnotintendedforusebypersons(including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

•Childrenshouldbesupervisedtoensurethattheydonot

play with the appliance.

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• Theappliancemustbeusedbyadultsonly,towashdomestic

crockery in accordance with the instructions in this manual.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the machine

exposed to rain and storms.

• Donottouchtheappliancewhenbarefoot.

• Whenunpluggingtheappliancealwayspulltheplugfrom

the mains socket, do not pull on the cable.

• Thewatersupplytapmustbeshutoffandtheplugshould

be removed from the electrical socket before cleaning the

appliance or carrying out any maintenance work.

• Iftheappliancebreaksdown,donotunderanycircumstances

touch the internal parts in an attempt to perform the repair

work yourself.

• Nevertouchtheheatingelement.

• Donotleanorsitontheopendooroftheappliance:thismay

cause the appliance to overturn.

• Thedoorshouldnotbeleftopenasitmaycreateadangerous

obstacle.

• Keepdetergentandrinseaidoutofreachofchildren.

• Thepackagingmaterialshouldnotbeusedasatoy.

Disposal

• Disposalofpackagingmaterials:observelocallegislationso

that the packaging may be reused.

• The European Directive 2012/19/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted appliances

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

 Forfurther information relating to the correct disposal of

household appliances, owners may contact the relevant

public authority or the local appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

• Onlybeginawashcyclewhenthedishwasherisfull.While

waiting for the dishwasher to be filled, prevent unpleasant

odours using the Soak cycle

(see Wash cycles).

• Selectawashcyclewhichissuitedtothetypeofcrockery

and to the soil level of the crockery using the

Table of wash

cycles:

 -Fordisheswithanormalsoillevel,usetheEcowashcycle,

which guarantees low energy and water consumption levels.

- If the load is smaller than usual activate the Half load option*

(see Start-up and use).

• Ifyourelectricitysupplycontractgivesdetailsofelectricity

saving time bands, run wash cycles during the periods when a

lower tariff is applied. The Delayed start

* button

(see Start-up

and use)

helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• Westronglyrecommendthatyouusedetergentsthatdonot

contain phosphates or chlorine, as these products are harmful

to the environment.

• Enzymesprovideaparticularlyeffectiveactionattemperatures

around 50°C, and as a result detergents containing enzymes

can be used in conjunction with low-temperature wash cycles

in order to achieve the same results as a normal 65°C wash

cycle.

• Toavoidwastingdetergent,usetheproductinappropriate

quantities based on the manufacturer’s recommendations,

the hardness of the water and the soil level and quantity

of crockery to be washed. Even if they are biodegradable,

detergents contain substances which may alter the balance

of nature.

* Only available in selected models.

Assistance

Before contacting Assistance:

• Checkwhethertheproblemcanberesolvedusingthe

Troubleshooting guide

(see Troubleshooting).

• Restarttheprogrammetocheckwhethertheproblemhas

ceased to exist.

• Iftheproblempersists,contacttheAuthorisedTechnical

Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

• Thetypeofmalfunction.

• Theappliancemodel(Mod.).

• Theserialnumber(S/N).

This information can be found on the appliance data plate

(see Description of the appliance).

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

* Only available in selected models.

Problem: Possible causes / Solutions:

The dishwasher does not start or

cannot be controlled

• Switch off the appliance by pressing the ON/OFF button, switch it back on after

approximately one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close • The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet nished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The lter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

use).

The dishes and glasses are

covered in a white lm or

limescale deposits.

• The level of the rened salt is low or the dosage setting is not suited to the hardness of

the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying program has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean. • The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

use).

• The lid on the rinse aid compartment has not been shut correctly.

• The lter is dirty or blocked (see Care and maintenance).

• The rened salt level is low (see Rinse aid and salt).

The dishwasher does not take any

water in - Tap shut-off alarm

(several short beeps are emitted

(the Drying and End indicator lights

ash).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when the beeps*

sounded. Switch off the appliance using the ON/OFF button, turn on the tap and switch

the appliance back on after 20 seconds by pressing the same button. Re-program the

appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet

lter blocked

(the Washing, Drying and End

indicator lights ashes).

• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to

eliminate the risk of ooding and remove the plug from the electrical socket.

Make sure the water inlet lter has not become blocked by impurities (see “Care and

maintenance” chapter).

Manual de

Instrucciones

Sumario

Instalación, 14-15

Colocación y nivelación

Conexiones hidráulicas y eléctricas

Advertencias para el primer lavado

Datos técnicos

Ecodesign Regulation

Descripción del aparato, 16

Vista de conjunto

Panel de control

Cargar los cestos, 17

Cesto inferior

Cesto de los cubiertos

Cesto superior

Puesta en funcionamiento y uso, 18-19

Poner en funcionamiento el lavavajillas

Cargar el detergente

Opciones de lavado

Programas, 20

Tabla de programas

Abrillantador y sal regeneradora, 21

Cargar el abrillantador

Cargar la sal regeneradora

Mantenimiento y cuidados, 22

Interrumpir el agua y la corriente eléctrica

Limpiar el lavavajillas

Evitar los malos olores

Limpiar los rociadores

Limpieza del filtro de entrada de agua

Limpiar los filtros

Si se ausenta durante largos períodos

Precauciones, consejos y Asistencia

Técnica, 23

Seguridad general

Eliminación

Ahorrar y respetar el medio ambiente

Asistencia Técnica

Anomalías y soluciones, 24

Español, 13

LSF 712

LAVAVAJILLAS

Instalación

Es importante conservar este manual para poder consultarlo

en cualquier momento. En caso de venta, de cesión o de

traslado, controle que permanezca junto con el aparato.

Lea atentamente las instrucciones: contienen información

importante sobre la instalación, sobre el uso y sobre la

seguridad.

En caso de traslado mantenga el aparato en posición

vertical; si fuera necesario inclinarlo, hágalo hacia la parte

posterior.

Este aparato ha sido proyectado para uso doméstico y para

aplicaciones similares, por ejemplo:

- Áreas destinadas a cocina para el personal de tiendas, oficinas

y otros ambientes de trabajo

- Casas agrícolas

- Uso por parte de clientes de hoteles, moteles y otros ambientes

residenciales

- Bed and breakfast.

Colocación y nivelación

1. Desembale el aparato y controle que no haya sufrido daños

durante el transporte.

Si estuviera dañado, no lo conecte y llame al revendedor.

2. Coloque el lavavajillas haciendo adherir los costados o la

parte posterior a los muebles adyacentes o a la pared. El aparato

también se puede empotrar debajo de una superficie de trabajo

continua

(ver la hoja de Montaje).

3. Coloque el lavavajillas sobre un piso plano y rígido. Compense

las irregularidades desenroscando o enroscando las patas

delanteras hasta que el aparato esté en posición horizontal.

Una cuidadosa nivelación brinda estabilidad y evita vibraciones,

ruidos y desplazamientos.

*. Para regular la altura de la pata posterior, accione el casquillo

hexagonal rojo que se encuentra en la parte inferior frontal y

central del lavavajillas, utilizando una llave de boca hexagonal

con una apertura de 8 mm. girando en sentido horario para

aumentar la altura y en sentido antihorario para disminuirla.

(ver la hoja de instrucciones para empotramiento anexada a

la documentación).

Conexiones hidráulicas y eléctricas

La adaptación de las redes eléctricas e hidráulicas para la

instalación debe ser realizada sólo por personal especializado.

El lavavajillas no se debe apoyar en los tubos ni en el cable

de alimentación eléctrica.

El aparato debe conectarse a la red de distribución de agua

empleando tubos nuevos.

No reutilice los tubos viejos.

Los tubos de carga y de descarga de agua y el cable de

alimentación eléctrica se pueden orientar hacia la derecha o

hacia la izquierda para permitir una mejor instalación.

Conexión del tubo de carga de agua

• Aunatomadeaguafría:enrosquebieneltubodecargaaun

grifo con boca roscada de ¾ gas; antes de enroscarlo, haga

correr agua hasta que salga límpida para que las impurezas

que pudiera contener no obstruyan el aparato.

• Aunatomadeaguacaliente:enelcasodeunainstalación

centralizada de radiadores, el lavavajillas se puede alimentar

con agua caliente de la red, mientras no supere una

temperatura de 60ºC.

Enrosque el tubo al grifo de la misma forma descrita para la

toma de agua fría.

Si la longitud del tubo de carga no es la adecuada, diríjase

a un negocio especializado o a un técnico autorizado

(ver

Asistencia Técnica).

La presión del agua debe estar comprendida entre los

valores indicados en la tabla de Datos técnicos

(ver al lado).

Controle que en el tubo no hayan pliegues ni estrangulaciones.

Conexión del tubo de descarga de agua

Conecte el tubo de descarga, sin plegarlo, a una tubería de

descarga con un diámetro mínimo de 4 cm.

El tubo de descarga debe estar a una altura comprendida

entre 40 y 80 cm. del piso o de la superficie de apoyo del

lavavajillas (A).

Antes de conectar el tubo de descarga del agua al sifón del

lavabo, quite el tapón de plástico (B).

Dispositivo de seguridad contra inundación

Para garantizar que no se produzcan inundaciones, el

lavavajillas:

- posee un sistema que interrumpe la entrada de agua en el

caso de anomalías o de pérdidas desde el interior.

Algunos modelos poseen un dispositivo adicional de seguridad

New Acqua Stop

*, que los protege contra inundaciones aún

en el caso de rotura del tubo de alimentación.

ATENCIÓN: ¡VOLTAJE PELIGROSO!

En ningún caso se debe cortar el tubo de carga de agua porque

contiene partes conectadas a una fuente eléctrica.

* Presente sólo en algunos modelos.

Conexión eléctrica

Antes de introducir el enchufe en la toma de corriente, controle

que:

• latomaposeaconexiónatierrayqueseaconformeconla

ley;

• latomaseacapazdesoportarlacargamáximadepotencia

de la máquina indicada en la placa de características

ubicada en la contrapuerta

(ver el capítulo Descripción del

lavavajillas);

• latensióndealimentaciónestécomprendidadentrodelos

valores indicados en la placa de características ubicada en

la contrapuerta;

• latomaseacompatibleconelenchufedelaparato.Sinoes

así, solicite la sustitución del enchufe a un técnico autorizado

(ver Asistencia Técnica)

; no utilice prolongaciones ni tomas

múltiples.

Una vez instalado el aparato, el cable de alimentación

eléctrica y la toma de corriente deben ser fácilmente accesibles.

El cable no se debe plegar ni comprimir.

Si el cable de alimentación está dañado, deberá ser

cambiado por el fabricante o por su servicio de asistencia

técnica a fin de prevenir riesgos. (Ver Asistencia)

La Empresa declina toda responsabilidad cuando no se

hayan respetado estas normas.

Cinta anticondensación*

Después de haber empotrado el lavavajillas, abra la puerta y

pegue la cinta adhesiva transparente debajo de la superficie de

madera para protegerla de una posible condensación.

Advertencias para el primer lavado

Después de la instalación e inmediatamente antes del primer

lavado, llene completamente de agua el depósito de sal

y agregue aproximadamente 1 kg. de sal

(ver el capítulo

Abrillantador y sal regeneradora

): es normal que el agua se

derrame. Seleccione el grado de dureza del agua

(ver el capítulo

Abrillantador y sal regeneradora).

- Después de la carga de sal,

la luz indicadora de FALTA DE SAL

* se apaga.

Cuando no se llena el contenedor de sal, se puede dañar

el ablandador de agua y el elemento que produce calor.

Datos técnicos

Dimensiones

ancho: 45 cm

altura: 85 cm

profundidad: 60 cm

Capacidad 10 cubiertos estándar

Presión del agua de

alimentación

0,05 ÷ 1MPa (0,5 ÷ 10 bar)

7,25 si – 145 psi

Tensión de

alimentación

Ver la placa de características

Potencia total

absorbida

Ver la placa de características

Fusible Ver la placa de características

Este aparato es conforme a

las siguientes Directivas de la

Comunidad:

-2006/95/EC (Bajo Voltaje)

-2004/108/EC (Compatibilidad

Electromagnética)

-97/17/CE (etiquetado)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-2012/19/CE

ECODESIGN REGULATION

Ciclo de lavado ECO es el programa estándar al que se refieren los datos de la etiqueta energética; este ciclo es adecuado para

lavar vajillas con suciedad normal y es el programa más eficiente en términos de consumo de energía y agua para este tipo de

vajilla. Para consumir menos utilice el lavavajillas a plena carga.

Consumos en modo stand-by: Consumo en modo left-on: 3 W - consumo en modo off: 1,3 W

Tabla de consumo de los principales ciclos

* Los datos del programa son valores de mediciones de laboratorio obtenidos según la norma europea EN 50242.

** Los datos se obtienen realizando mediciones en las condiciones de uso y carga de vajillas del usuario.

Condiciones estándar* Condiciones usuario**

Consumo de

energía (kWh/ciclo)

Consumo de

agua (l/ciclo)

Duración (min/ciclo)

Consumo de energía

(kWh/ciclo)

Consumo de

agua (l/ciclo)

Duración (min/ciclo)

INTENSIVO

1,30 14 150 1,15 14 140

NORMAL

1,05 14 115 0,95 13 110

Vista de conjunto

Descripción del aparato

1. Cesto superior

2. Rociador superior

3. Cestos adicionales

4. Regulador de la altura del cesto

5. Cesto inferior

6. Rociador inferior

7. Cesto para cubiertos

8. Filtro de lavado

9. Depósito de sal

10. Cubetas de detergente y depósito de

abrillantador

11.

Placa de características

12. Panel de control***

***

Sólo en los modelos con empotramiento total.

* Presente sólo en algunos modelos.

La cantidad y el tipo de programas y opciones varían según el modelo de lavavajillas.

Panel de control

Piloto Fin y comienzo

retrasado 9 h.*

Piloto Secado y comienzo

retrasado 6 h.*

Piloto Lavado y comienzo

retrasado 3 h.*

Botón y piloto Puesta en

marcha/Pausa

Botón Comienzo

retrasado*

Piloto

Falta de Sal*

Botón y piloto

Media carga*

Botón de Selección

de Programas

Botón

ON-OFF/Reset

Cargar los cestos

Antes de cargar los cestos, elimine de la vajilla los

residuos de alimentos y vacíe los vasos y copas.

Coloque la vajilla cuidando que quede bien firme y que no

se vuelque.

Después de haber realizado la carga, controle que los

rociadores giren libremente.

Cesto inferior

El cesto inferior puede contener ollas, tapas, platos, ensaladeras,

cubiertos, etc.según los

Ejemplos de carga.

Los platos y tapas grandes se deben colocar preferentemente

a los costados del cesto, cuidando no bloquear la rotación del

rociador superior.

Algunos modelos de lavavajillas poseen

sectores reclinables

*, los mismos se

pueden utilizar en posición vertical para

colocar platos o en posición horizontal

para colocar ollas y ensaladeras.

Cesto de los cubiertos

El cesto de los cubiertos puede ser diferente según el modelo

de lavavajillas. El cesto de los cubiertos se debe colocar frontal-

mente, sobre el cesto inferior, haciéndolo correr entre las partes

fijas, o sobre el cesto superior, cuando se realiza un lavado con

media carga (en los modelos que poseen dicha opción).

- Posee cestos adicionales

deslizables que permiten

una disposición óptima de

los cubiertos.

Los cuchillos y utensilios con puntas cortantes deben

colocarse en el cesto para cubiertos con las puntas hacia abajo

o dispuestos en los cestos especiales adicionales del cesto

superior en posición horizontal.

Ejemplos de colocación del cesto para cubiertos

Cesto superior

Cargue en este cesto la vajilla delicada y liviana: vasos, tazas

de té y de café, platitos, ensaladeras bajas, sartenes, ollas

bajas poco sucias, como se indica en los

Ejemplos de carga.

• Tazas y tacitas, cuchillos largos y puntiagudos, cubiertos

para servir: colóquelas en los cestos adicionales**.

Cestos adicionales con inclinación variable*

- La inclinación permite obtener mayor espacio en el cesto

superior, colocar copas con pies de diferentes longitudes y

mejorar las prestaciones de secado.

- Levante el cesto adicional, hágalo correr ligeramente y

colóquelo con la inclinación deseada.

Regular la altura del cesto superior

Para facilitar la colocación de la vajilla, se puede ubicar el cesto

superior en posición alta o baja.

Es preferible regular la altura del cesto superior con el

CESTO VACÍO.

No levante ni baje el cesto de un solo lado.

Abra los sujetadores de las guías del

cesto, a la izquierda y a la derecha, y

extráigalo; colóquelo arriba o abajo,

hágalo deslizar a lo largo de las guías

hasta hacer entrar también las ruedas

delanteras y cierre los sujetadores (

ver

la figura).

Si el cesto posee manijas Dual Space*

(ver la figura),

lleve el cesto superior

hasta el final del recorrido, coja las

manijas a los costados del cesto y

muévalo hacia arriba o hacia abajo; deje

caer el cesto acompañándolo.

Ejemplos de carga del cesto superior

Ejemplos de carga del cesto inferior

Vajilla no adecuada para el lavado en lavavajillas

• Objetosdemadera,conempuñadurademaderaodecuerno

o con partes encoladas.

• Objetosdealuminio,cobre,latón,peltreoestaño.

• Vajilladeplásticoquenoseatermorresistente.

• Porcelanasantiguasopintadasamano.

• Vajilladeplataantigua.Lavajilladeplataquenoesantigua,

en cambio, se puede lavar con un programa delicado y

controlando que no esté en contacto con otros metales.

Se aconseja el uso de vajilla adecuada para el lavado en

lavavajillas.

* Presente sólo en algunos modelos.

** Cantidad y posición variables.

Inclinación A Inclinación B Inclinación C

Puesta en

funcionamiento y uso

Poner en funcionamiento el lavavajillas

1. Abra el grifo de agua.

2. Presione el botón ENCENDIDO-APAGADO: todos los pilotos

presentes en el panel de mandos se iluminan durante algunos

segundos.

3. Abra la puerta y dosifique el detergente

(ver más adelante)

4. Cargue los cestos

(ver Cargar los cestos)

y cierre la puerta.

5. Seleccione el programa girando el mando de SELECCIÓN

DE PROGRAMA en sentido horario: haga coincidir la muesca

que se encuentra en el mando con el número o con el símbolo

del programa. El piloto correspondiente al botón PUESTA EN

FUNCIONAMIENTO/PAUSA centelleará.

6. Seleccione las opciones de lavado*

(ver al lado).

7. Ponga en funcionamiento presionando el botón PUESTA

EN FUNCIONAMIENTO, el piloto dejará de centellear (luz fija).

El encendido del piloto correspondiente al lavado indica el

comienzo del programa.

8. Al final del programa se ilumina el piloto FIN (luz fija). Apague

el aparato presionando el botón ENCENDIDO-APAGADO, cierre

el grifo de agua y desenchufe el aparato.

9. Espere algunos minutos antes de quitar la vajilla para evitar

quemarse. Descargue los cestos comenzando por el inferior.

- Para disminuir el consumo de energía eléctrica,

en algunos casos en que NO se utiliza, la máquina se

apaga automáticamente.

Modificar un programa en curso

Si no se ha seleccionado el programa deseado, es posible

modificarlo, siempre que haya comenzado recién: una

vez comenzado el lavado, para cambiar el ciclo de lavado

apague la máquina presionando en forma prolongada el botón

ENCENDIDO/APAGADO/Reset, vuelva a encenderla con el

mismo botón y seleccione nuevamente el programa y las

opciones deseadas.

Agregar vajilla

Presione el botón Puesta en funcionamiento/Pausa, (la luz del

botón centellea). Abra la puerta teniendo cuidado con el escape

de vapor e introduzca la vajilla. Presione el botón Puesta en

funcionamiento/Pausa (luz fija): el ciclo se reanudará.

Presionando el botón Puesta en funcionamiento/Pausa para

poner la máquina en pausa, se interrumpe tanto el programa

como el Comienzo Retrasado, si se había fijado.

En esta fase no se puede cambiar el programa.

Interrupciones accidentales

Si durante el lavado se abre la puerta o se produce una

interrupción de corriente, el programa se interrumpe. Cuando se

cierra la puerta o vuelve la corriente, el programa se reanudará

a partir del punto en el que se había interrumpido.

Cargar el detergente

Los buenos resultados de un lavado dependen también de la

correcta dosificación del detergente, si se excede, no se lava

más eficazmente y se contamina el medio ambiente.

Utilice sólo detergente para lavavajillas.

NO UTILICE detergentes para lavado a mano.

Al finalizar el ciclo, un uso excesivo de detergente

puede dejar residuos de espuma.

El uso de las pastillas se aconseja sólo en los

modelos que poseen la opción PASTILLAS MULTI-

FUNCIÓN.

Las mejores prestaciones de lavado y secado se

obtienen sólo con el uso de detergente en polvo, abril-

lantador líquido y sal.

cubeta A: Detergente para lavado

cubeta B: Detergente para prelavado

1. Abra la tapa C presionando el

botón D.

2. Dosifique el detergente

consultando la

Tabla de programas

•enpolvo:cubetasAyB.

•enpastillas:sielprogramanecesita

una, colóquela en la cubeta A y cierre

la tapa; si necesita dos, coloque la

segunda en el fondo de la cuba.

3. Elimine los residuos de detergente de los bordes de la cubeta

y cierre la tapa hasta el enganche.

* Presente sólo en algunos modelos.

Opciones de lavado*

Las OPCIONES pueden ser elegidas, modificadas o anuladas

sólo después de haber elegido el programa de lavado y antes

de haber presionado el botón Puesta en funcionamiento/Pausa.

Pueden seleccionarse sólo las opciones compatibles con el

tipo de programa elegido. Si una opción no es compatible con

el programa seleccionado,

(ver la tabla de programas)

el led

correspondiente centelleará velozmente 3 veces.

Si se selecciona una opción incompatible con otra o con un

programa de lavado precedentemente elegido, la opción

no compatible centellea 3 veces y se apaga, mientras que

permanece encendida al última selección realizada.

Para deseleccionar una opción erróneamente elegida, presione

de nuevo el botón correspondiente.

Comienzo retrasado

Es posible postergar 3, 6 o 9 horas el comienzo del programa.

Después de haber seleccionado un programa de lavado y

eventualmente otras opciones, seleccione el retraso deseado

presionando, las veces necesarias, el botón de Comienzo Re-

trasado; los pilotos de lavado (3 horas), secado (6 horas) y

fin (9 horas) centellearán sucesivamente.

Si se presiona nuevamente el botón Comienzo Retrasado, se

deselecciona la opción.

Una vez realizada la selección, presionando el botón Puesta en

funcionamiento/Pausa comenzará la cuenta al revés, el piloto

del retraso seleccionado centelleará y el botón Puesta en fun-

cionamiento/Pausa dejará de centellear (luz fija).

Una vez cumplido el tiempo, el piloto del retraso seleccionado

dejará de centellear (luz fija) y el programa comenzará.

No es posible seleccionar el Comienzo Retrasado de-

spués que el ciclo ha comenzado.

Media carga

Si la vajilla que debe lavar es poca, se puede utilizar la

media carga que permite ahorrar agua, energa y detergente.

Seleccione el programa y presione el botn MEDIA CARGA: el

piloto se iluminar.

Recuerde que debe reducir a la mitad la cantidad de

detergente.

Es preferible utilizar detergente en polvo.

Programas

Nota:

Las mejores prestaciones de los programas “Cotidiano y Rápido” se obtienen preferiblemente respetando la cantidad de cubiertos

especificados.

* El programa Eco respeta la norma EN-50242, tiene una duración mayor que la de otros programas pero es el que produce el

menor consumo de energía y además respeta el medio ambiente.

Nota para los Laboratorios de Pruebas: para obtener información detallada sobre las condiciones de la prueba comparativa EN,

consulte la siguiente dirección: [email protected]

Para facilitar la dosificación del detergente, es importante saber que:

1 cucharada = 15 gr. de polvo = 15 ml. de líquido aproximadamente - 1 cucharadita = 5 gr. de polvo = 5 ml. de líquido aproximadamente

Si la vajilla está poco sucia o ha sido aclarada precedentemente bajo el agua, recuerde disminuir la dosis de detergente.

La cantidad y el tipo de programas y opciones varían según el modelo de lavavajillas.

Indicaciones para la

selección de programas

Programa

Detergente

(A) = cubeta A

(B) = cubeta B

Secado Opciones

Duración del

programa

(tolerancia

±10%)

Hrs. Min.

en polvo Líquido Pastillas

Vajilla y ollas muy sucias (no

usar para piezas delicadas).

1. Intensivo

25 g (A) 25 ml (A) 1 (A) Si

Comienzo

retrasado

Media carga

2:25’

Vajilla y ollas normalmente

sucias. Programa estándar

diario.

2. Normal

21 g (A)

4 g (B)

21 ml (A)

4 ml (B)

1 (A) Si

Comienzo

retrasado

Media carga

1:50’

Vajilla con la suciedad diaria en

cantidad limitada. (4 cubiertos +

1 olla + 1 sartén).

3. Cotidiano

25 g (A) 25 ml (A) 1 (A) No

Comienzo

retrasado

Media carga

1:00’

Lavado preliminar a la espera

de completar la carga en la

comida sucesiva.

4. Remojo

No No No No

Comienzo

retrasado

Media carga

0:08’

Lavado ecológico de

bajo consumo energético,

adecuado para vajilla y ollas.

5. Eco

21 g (A)

4 g (B)

21 ml (A)

4 ml (B)

1 (A) Si

Comienzo

retrasado

Media carga

3:00’

Ciclo económico y veloz que

se utiliza inmediatamente

después del uso para vajilla

poco sucia. (2 platos + 2 vasos

+ 4 cubiertos + 1 olla + 1

sartén pequeña)

6. Rápido

21 g (A) 21 ml (A) 1 (A) No

Comienzo

retrasado

0:35’

Ciclo económico y veloz que

se utiliza inmediatamente

después del uso, para vajilla

delicada más sensible a las

altas temperaturas. (copas,

cesto superior + platos

delicados, cesto inferior).

7. Cristalería

na

25 g (A) 25 ml (A) 1 (A) Si

Comienzo

retrasado

Media carga

1:35’

Sayfa yükleniyor ...

Whirlpool LSF 712 EUHA Kullanici rehberi

Marka: Whirlpool

Model: LSF 712 EUHA

Kategori: Bulaşık makineleri

Tip: Kullanici rehberi

PDF İndir

rapor

Diğer dillerde

español: Whirlpool LSF 712 EUHA Guía del usuario
polski: Whirlpool LSF 712 EUHA instrukcja

Whirlpool LSF 712 EUHA Kullanici rehberi

Whirlpool LSF 712 EUHA Kullanici rehberi

Diğer dillerde

İlgili Makaleler

Diğer Belgeler