Simplicity 359775-0001-E1 Kullanım kılavuzu

Marka: Simplicity

Modeli: 359775-0001-E1

Kategori: Motorlu taşıt aksesuarları

Tip: Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Not for

Reproduction

80006738EST

BRIGGS & STRATTON is a registered

trademark of Briggs & Stratton Corporation.

Revision: B

Not for

Reproduction

2 VanguardEngines.com

Not for

Reproduction

This manual contains safety information to make you aware of the hazards and risks

associated with engines and how to avoid them. It also contains instructions for the proper

use and care of the engine. Because Briggs & Stratton Corporation does not necessarily

know what equipment this engine will power, it is important that you read and understand

these instructions and the instructions for the equipment. Save these original instructions

for future reference.

Note:

The figures and illustrations in this manual are provided for reference only and may

differ from your specific model. Contact your dealer if you have questions.

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your engine

(see the

Features and Controls

section).

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

Look for the 2D barcode located on some

engines. When viewed with a 2D-capable

device, the code will bring up our website

where you can access support information

for this product. Data rates apply. Some

countries may not have online support

information available.

Recycling Information

All packaging, used oil, and batteries should be recycled

according to applicable government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with

the alert symbol to indicate the likelihood and the potential severity of injury. In addition, a

hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious

injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE

indicates an situation that could result in damage to the product.

Hazard Symbols and Meanings

MeaningSymbolMeaningSymbol

Read and understand the

Operator's Manual before

operating or servicing the unit.

Safety information about

hazards that can result in

personal injury.

Explosion hazardFire hazard

MeaningSymbolMeaningSymbol

Toxic fume hazardShock hazard

Noise hazard - Ear protection

recommended for extended

use.

Hot surface hazard

Explosion hazardThrown object hazard -

Wear eye protection.

Kickback hazardFrostbite hazard

Chemical HazardAmputation hazard - moving

parts

CorrosiveThermal heat hazard

Safety Messages

WARNING

Certain components in this product and its related accessories contain chemicals

known to the State of California to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Briggs & Stratton Engines are not designed for and are not to be used to power: fun-

karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs); motorbikes;

hovercraft; aircraft products; or vehicles used in competitive events not sanctioned by

Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact

Briggs & Stratton Engine Application Center, 1-866-927-3349. Improper engine

application may result in serious injury or death.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Before you start the engine,

make sure you add oil according to the instructions in this manual. If you start the

engine without oil, it will be damaged beyond repair and will not be covered under

warranty.

WARNING

Gaseous vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Fill fuel tank outdoors or in well-ventilated area.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if

necessary.

When Starting Engine

Not for

Reproduction

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in place

and secured.

• Do not crank engine with spark plug removed.

When Operating Equipment

• Never start or run the engine with the air cleaner assembly (if equipped) or the air

filter (if equipped) removed.

When Transporting Equipment

• On Natural / Liquid Petroleum (LP) Gas engines, transport with fuel cylinder empty

or valve closed, or fuel tank disconnected.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or other appliances that have pilot

lights or other ignition sources because they can ignite fuel vapors.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or

taste it. Even if you do not smell exhaust fumes, you could still be exposed to

carbon monoxide gas. If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You may have carbon

monoxide poisoning.

• Operate this product ONLY outside far away from windows, doors and vents to

reduce the risk of carbon monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms

with battery back-up according to the manufacturer's instructions. Smoke alarms

cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements, crawlspaces, sheds,

or other partially-enclosed spaces even if using fans or opening doors and windows

for ventilation. Carbon monoxide can quickly build up in these spaces and can linger

for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine

faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

• When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

• Remove all external equipment / engine loads before starting engine.

• Direct-coupled equipment components such as, but not limited to, blades, impellers,

pulleys, sprockets, etc., must be securely attached.

WARNING

Rotating parts can contact or entangle hands, feet, hair, clothing, or accessories.

Traumatic amputation or severe laceration can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling drawstrings or items that could become

caught.

WARNING

Running engines produce heat. Engine parts, especially muffler, become

extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or operate

the engine on any forest-covered, brush-covered, or grass-covered land unless the

exhaust system is equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal jurisdictions may have

similar laws. Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed on this engine.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic amputation, or

laceration.

Fire hazard

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only correct tools.

• Do not tamper with governor spring, links or other parts to increase engine speed.

• Replacement parts must be of the same design and installed in the same position

as the original parts. Other parts may not perform as well, may damage the unit,

and may result in injury.

• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

WARNING

Gaseous fuels are extremely flammable and readily form explosive air-vapor

mixtures at ambient temperatures.

If you smell gas:

• Do not start the engine.

• Do not actuate any electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or fire department.

WARNING

Wear eye protection when doing repair work.

Frostbite can result from skin / eye contact with leaking LP liquid.

• Installation, adjustment and repair work should be done by a qualified technician.

• Regularly check flexible supply line. Make sure they are in good condition. Replace

damaged or leaking components.

WARNING

Missing or inoperative "fuel lock-off" valve can cause a fire or explosion.

• Do not operate the equipment if the "fuel lock-off" valve is missing or inoperative.

4 VanguardEngines.com

Not for

Reproduction

Features and Controls

Engine Controls

Compare the illustration (Figure: 1, 2, 3) with your engine to familiarize yourself with the

location of various features and controls.

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Air Cleaner

D. Dipstick

E. Oil Filter (if equipped)

F. Oil Drain Plug

G. Oil Pressure Sensor

H. Air Intake Grille

I. Electric Starter

J. Rewind Starter (if equipped)

K. LPG/NG Mixer

L. Exhaust Manifold

M. Muffler (if equipped)

N. Oil Cooler (if equipped)

Control Symbols and Meanings

MeaningSymbolMeaningSymbol

Engine speed - SlowEngine speed - Fast

On - OffEngine speed - Stop

Operation

Oil Recommendations

Oil Capacity: See the

Specifications

section.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers

or dealers may have added oil to the engine. Before you start the engine for the first

time, make sure to check the oil level and add oil according to the instructions in this

manual. If you start the engine without oil, it will be damaged beyond repair and will not

be covered under warranty.

We recommend the use of Briggs & Stratton Warranty Certified oils for best performance.

Other high-quality detergent oils are acceptable if classified for service SF, SG, SH, SJ or

higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best viscosity for the outdoor temperature range expected. Engines on most

outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment operated

in hot temperatures, Vanguard™ 15W-50 Synthetic oil provides the best protection.

SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.A

10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Check oil level more frequently.

5W-30C

Synthetic 5W-30D

Vanguard™ Synthetic 15W-50E

Check and Add Oil

See Figure: 4

Before checking or adding oil

• Make sure the engine is level.

• Clean the oil fill area of any debris.

• See the

Specifications

section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers

or dealers may have added oil to the engine. Before you start the engine for the first

time, make sure to check the oil level and add oil according to the instructions in this

manual. If you start the engine without oil, it will be damaged beyond repair and will not

be covered under warranty.

Check Oil Level

1. Remove the dipstick (A, Figure 4) and wipe with a clean cloth.

2. Install and tighten the dipstick (A, Figure 4).

3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full

indicator (B, Figure 4) on the dipstick.

Add Oil

1. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 4). Do not overfill.

After adding oil, wait one minute and then check the oil level.

2. Reinstall and tighten the dipstick (A, Figure 4).

Low Oil Protection System (if equipped)

Some engines are equipped with a low oil sensor. If the oil is low, the sensor will either

activate a warning light or stop the engine. Stop the engine and follow these steps before

restarting the engine.

• Make sure the engine is level.

• Check the oil level. See the

Check Oil Level

section.

• If the oil level is low, add the proper amount of oil. Start the engine and make sure

the warning light (if equipped) is not activated.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to have the oil problem corrected.

Fuel Recommendations

WARNING

Missing or inoperative "fuel lock-off" valve can cause a fire or explosion.

• Do not operate the equipment if the "fuel lock-off" valve is missing or inoperative.

Fuel must meet these requirements

Not for

Reproduction

• Use clean, dry fuel, free of moisture or any particulate material. Using fuels outside

the following recommended values may cause performance problems.

• In engines set up to run on LPG, commercial grade HD5 LPG is recommended.

Recommended fuel composition is fuel with a minimum fuel energy of 2500 BTU's/ft³

with maximum propylene content of 5% and butane and heavier gas content of 2.5%

and minimum propane content of 90%.

NG or LPG engines are certified to operate on natural or liquid propane gas. The emissions

control system for this engine is EM (Engine Modifications).

WARNING

The equipment on which this engine is mounted is equipped with an automatic safety

gas "fuel lock-off" valve. Do not operate the equipment if the "fuel lock-off" valve is

missing or inoperative

Add Fuel

WARNING

Gaseous vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Fill fuel tank outdoors or in well-ventilated area.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace is

necessary.

For information on refueling natural or LP gas engines, read the operating instructions

supplied by the equipment manufacturer.

Start and Stop Engine

See Figure: 5

Start Engine

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine

faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

• When starting engine, pull the starter cord slowly until resistance is felt and then pull

rapidly to avoid kickback.

WARNING

Gaseous vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, and air cleaner (if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or taste

it. Even if you do not smell exhaust fumes, you could still be exposed to carbon

monoxide gas. If you start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor. You may have carbon

monoxide poisoning.

• Operate this product ONLY outside far away from windows, doors and vents to reduce

the risk of carbon monoxide gas from accumulating and potentially being drawn

towards occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms

with battery back-up according to the manufacturer's instructions. Smoke alarms

cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements, crawlspaces, sheds,

or other partially-enclosed spaces even if using fans or opening doors and windows

for ventilation. Carbon monoxide can quickly build up in these spaces and can linger

for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Note:

Equipment may have remote controls. See the equipment manual for location and

operation of remote controls.

1. Check the engine oil. See the

Check Oil Level

section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 5), if equipped, to the OPEN position.

4. Push the stop switch (F, Figure 5), if equipped, to the ON position.

5. Move the throttle control (B, Figure 5), if equipped, to the FAST position. Operate

the engine in the FAST position.

6. Rewind Start, if equipped with key switch: Turn the key switch (D, Figure 5) to

the ON position.

7. Rewind Start, if equipped: Firmly hold the starter cord handle (E, Figure 5). Pull

the starter cord handle slowly until resistance is felt, then pull rapidly.

WARNING

Rapid retraction of the starter cord (kickback) will pull your hand and arm toward the

engine faster than you can let go. Broken bones, fractures, bruises or sprains could

result. When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

8. Electric Start, if equipped: Turn the electric start switch (D, Figure 5) to the ON or

START position.

NOTICE

To extend the life of the starter, use short starting cycles (five seconds

maximum). Wait one minute between starting cycles.

Note:

If the engine does not start after repeated attempts, contact your local dealer or go

to VanguardEngines.com or call 1-800-999-9333 (in USA).

Stop Engine

1. Stop Switch, if equipped: Push the stop switch (F, Figure 5) to the OFF position.

Key Switch, if equipped: With the throttle control in the SLOW position, turn the

key switch (D, Figure 5) to the OFF position. Remove the key and keep in a safe

place out of the reach of children.

2. After the engine stops, move the fuel shut-off (A, Figure 5), if equipped, to the

CLOSED position.

Maintenance

NOTICE

If the engine is tipped during maintenance, the fuel tank, if mounted on

engine, must be empty and the spark plug side must be up. If the fuel tank is not empty

and if the engine is tipped in any other direction, it may be difficult to start due to oil or

gasoline contaminating the air filter and/or the spark plug.

WARNING

When performing maintenance that requires the unit to be tipped, the fuel tank, if mounted

on the engine, must be empty or fuel can leak out and result in a fire or explosion.

We recommend that you see any Briggs & Stratton Authorized Service Dealer for all

maintenance and service of the engine and engine parts.

NOTICE

All the components used to build this engine must remain in place for proper

operation.

6 VanguardEngines.com

Not for

Reproduction

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic amputation, or

laceration.

Fire hazard

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only correct tools.

• Do not tamper with governor spring, links or other parts to increase engine speed.

• Replacement parts must be of the same design and installed in the same position

as the original parts. Other parts may not perform as well, may damage the unit, and

may result in injury.

• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Emissions Control Service

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any off-road engine repair establishment or individual. However,

to obtain "no charge" emissions control service, the work must be performed by a factory

authorized dealer. See the Emissions Control Statements.

Maintenance Schedule

Every 8 Hours or Daily

• Check engine oil level

• Clean area around muffler and controls

Every 100 Hours or Annually

• Replace spark plugs

• Change engine oil

• Replace oil filter (if equipped)

• Clean or change air filter

• Clean pre-cleaner (if equipped)

• Service exhaust system

• Check valve clearance

Every 400 Hours or Annually

• Service cooling system

• Clean oil cooler fins

In dusty conditions or when airborne debris is present, clean more often.

Not required unless engine performance problems are noted.

Service Spark Plug

See Figure: 6

Check the gap (A, Figure 6) with a wire gauge (B). If necessary, reset the gap. Install and

tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications

section.

Note:

In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same type

for replacement.

Service Exhaust System

WARNING

Running engines produce heat. Engine parts, especially muffler, become extremely

hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or operate

the engine on any forest-covered, brush-covered, or grass-covered land unless the

exhaust system is equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal jurisdictions may have

similar laws. Contact the original equipment manufacturer, retailer, or dealer to obtain

a spark arrester designed for the exhaust system installed on this engine.

Remove accumulated debris from muffler and cylinder area. Inspect the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

inspect for damage or carbon blockage. If damage is found, install replacement parts before

operating.

WARNING

Replacement parts must be of the same design and installed in the same position as

the original parts. Other parts may not perform as well, may damage the unit, and may

result in injury.

Change Engine Oil

See Figure: 7, 8, 9

Used oil is a hazardous waste product and must be disposed of properly. Do not discard

with household waste. Check with your local authorities, service center, or dealer for safe

disposal/recycling facilities.

Remove Oil

1. With engine off but still warm, disconnect the spark plug wire(s) (D, Figure 7) and

keep it away from the spark plug(s) (E).

2. Remove the dipstick (A, Figure 8).

3. Remove the oil drain plug (F, Figure 9). Drain the oil into an approved container.

4. After the oil has drained, install and tighten the oil drain plug (F, Figure 9).

Change Oil Filter, if equipped

Some models are equipped with an oil filter. For replacement intervals, see the

Maintenance Schedule.

1. Drain the oil from the engine. See

Remove Oil

section.

2. Remove the oil filter (G, Figure 9) and dispose of properly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket with fresh,

clean oil.

4. Install the oil filter by hand until the gasket contacts the oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. See

Add Oil

section.

6. Start and run the engine. As the engine warms up, check for oil leaks.

7. Stop the engine and check the oil level. Correct oil level is at the top of the full indicator

(B, Figure 8) on the dipstick.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of any debris.

• See the

Specifications

section for oil capacity.

1. Remove the dipstick (A, Figure 8) and wipe with a clean cloth.

2. Slowly pour oil into the engine oil fill (C, Figure 8). Do not overfill. After adding oil,

wait one minute and then check the oil level.

3. Install and tighten the dipstick (A, Figure 8).

Not for

Reproduction

4. Remove the dipstick and check the oil level. Correct oil level is at the top of the full

indicator (B, Figure 8) on the dipstick.

5. Reinstall and tighten the dipstick (A, Figure 8).

6. Connect the spark plug wire(s) (D, Figure 7) to the spark plug(s) (E).

Service Air Filter

See Figure: 10

WARNING

Gaseous vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Never start and run the engine with the air cleaner assembly (if equipped) or the air

filter (if equipped) removed.

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air can

damage the filter and solvents will dissolve the filter.

See the

Maintenance Schedule

for service requirements.

Various models use either a foam or a paper filter. Some models may also have an optional

pre-cleaner that can be washed and reused. Compare the illustrations in this manual with

the type installed on your engine and service as follows.

1. Open the fastener(s) (A, Figure 10) and remove the cover (B).

2. Remove the nut (C, Figure 10) and the retainer (D).

3. To prevent debris from falling into the carburetor, carefully remove the air filter (E,

Figure 10) .

4. To loosen debris, gently tap the filter on a hard surface. If the filter is excessively

dirty, replace with a new filter.

5. Remove the pre-cleaner (F, Figure 10), if equipped, from the air filter (E).

6. Wash the pre-cleaner (F, Figure 10), if equipped, in liquid detergent and water. Allow

the pre-cleaner to thoroughly air dry. Do not oil the pre-cleaner.

7. Install the dry pre-cleaner (F, Figure 10), if equipped, to the air filter (E).

8. Install the air filter (E, Figure 10) and secure with retainer (D) and nut (C).

9. Install the cover (B, Figure 10) and secure with the fastener(s) (A).

Service Cooling System

WARNING

Running engines produce heat. Engine parts, especially muffler, become extremely

hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc., can catch fire.

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

NOTICE

Do not use water to clean the engine. Water could contaminate the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to

overheat, resulting in poor performance and reduced engine life.

1. Use a brush or dry cloth to remove debris from the air intake grille.

2. Keep linkage, springs and controls clean.

3. Keep the area around and behind the muffler, if equipped, free of any combustible

debris.

4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.

After a period of time, debris can accumulate in the cylinder cooling fins and cause the

engine to overheat. This debris cannot be removed without partial disassembly of the

engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air

cooling system as recommended in the

Maintenance Schedule.

Storage

WARNING

Gaseous vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or other appliances that have pilot

lights or other ignition sources because they can ignite fuel vapors.

Engine Oil

While the engine is still warm, change the engine oil. See the

Change Engine Oil

section.

NOTICE

Store the engine level (normal operating position). If the engine is tipped in

any other direction, it may be difficult to start due to oil contaminating the air filter and/or

the spark plug.

Troubleshooting

For assistance, contact your local dealer or go to VanguardEngines.com or call 1-800-

999-9333 (in USA).

Specifications

Model: 290000, 300000

29.23 ci (479 cc)Displacement

2.677 in (68 mm)Bore

2.598 in (66 mm)Stroke

46 - 48 oz (1,36 - 1,42 L)Oil Capacity

.020 in (,51 mm)Spark Plug Gap

180 lb-in (20 Nm)Spark Plug Torque

.008 - .012 in (,20 - ,30 mm)Armature Air Gap

.004 - .006 in (,10 - ,15 mm)Intake Valve Clearance

.007 - .009 in (,18 - ,23 mm)Exhaust Valve Clearance

Model: 350000

34.78 ci (570 cc)Displacement

2.835 in (72 mm)Bore

2.756 in (70 mm)Stroke

46 - 48 oz (1,36 - 1,42 L)Oil Capacity

.020 in (,51 mm)Spark Plug Gap

180 lb-in (20 Nm)Spark Plug Torque

.008 - .012 in (,20 - ,30 mm)Armature Air Gap

.004 - .006 in (,10 - ,15 mm)Intake Valve Clearance

.007 - .009 in (,18 - ,23 mm)Exhaust Valve Clearance

Model: 380000

38.26 ci (627 cc)Displacement

2.972 in (75,5 mm)Bore

2.756 in (70 mm)Stroke

46 - 48 oz (1,36 - 1,42 L)Oil Capacity

.020 in (,51 mm)Spark Plug Gap

180 lb-in (20 Nm)Spark Plug Torque

.008 - .012 in (,20 - ,30 mm)Armature Air Gap

.004 - .006 in (,10 - ,15 mm)Intake Valve Clearance

.007 - .009 in (,18 - ,23 mm)Exhaust Valve Clearance

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily at

8 VanguardEngines.com

Not for

Reproduction

an angle up to 15°. Refer to the equipment operator's manual for safe allowable operating

limits on slopes.

Service Parts - Model: 290000, 300000, 350000, 380000

Part NumberService Part

394018Air Filter (Models 290000, 330000)

841359Air Filter (Models 350000, 380000)

272490Air Filter Pre-cleaner

100028Oil - SAE 30

842921Oil Filter

491055Resistor Spark Plug

696202, 5066Long Life Platinum Spark Plug

19374Spark Plug Wrench

19368Spark Tester

We recommend that you see any Briggs & Stratton Authorized Dealer for all maintenance

and service of the engine and engine parts.

Warranty

Briggs & Stratton Engine Warranty

Effective January 2017

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or

replace, free of charge, any part that is defective in material or workmanship or both.

Transportation charges on product submitted for repair or replacement under this warranty

must be borne by purchaser. This warranty is effective for and is subject to the time periods

and conditions stated below. For warranty service, find the nearest Authorized Service

Dealer in our dealer locator map at BRIGGSandSTRATTON.COM. The purchaser must

contact the Authorized Service Dealer, and then make the product available to the

Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some

states or countries do not allow limitations on how long an implied warranty lasts, and

some states or countries do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation and exclusion may not apply to you. This

warranty gives you specific legal rights and you may also have other rights which vary

from state to state and country to country

Standard Warranty Terms

1, 2, 3

Commercial

Use

Consumer

Use

Brand / Product Name

36 months36 monthsVanguard™; Commercial Series

12 months24 monthsEngines Featuring Dura-Bore™ Cast Iron Sleeve

3 months24 monthsAll Other Engines

These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing of

current warranty terms for your engine, go to BRIGGSandSTRATTON.com or contact

your Briggs & Stratton Authorized Service Dealer.

There is no warranty for engines on equipment used for prime power in place of a

utility or for standby generators used for commercial purposes. Engines used in

competitive racing or on commercial or rental tracks are not warrantied.

Vanguard installed on standby generators: 24 months consumer use, no warranty

commercial use. Vanguard installed on utility vehicles: 24 months consumer use, 24

months commercial use. Commercial Series with manufacturing date before July

2017, 24 months consumer use, 24 months commercial use.

In Australia - Our goods come with guarantees that cannot be excluded under the

Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure. For warranty

service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing

to [email protected], Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, Moorebank, NSW , Australia, 2170.

The warranty period begins on the original date of purchase by the first retail or commercial

consumer. "Consumer use" means personal residential household use by a retail consumer.

"Commercial use" means all other uses, including use for commercial, income producing

or rental purposes. Once an engine has experienced commercial use, it shall thereafter

be considered as a commercial use engine for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase

date at the time warranty service is requested, the manufacturing date of the product

will be used to determine the warranty period. Product registration is not required

to obtain warranty service on Briggs & Stratton products.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only, and

not replacement or refund of the equipment to which the engine may be mounted. Routine

maintenance, tune-ups, adjustments, or normal wear and tear are not covered under this

warranty. Similarly, warranty is not applicable if the engine has been altered or modified

or if the engine serial number has been defaced or removed. This warranty does not cover

engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than

10%, or the use of alternative fuels such as liquefied petroleum or natural gas on

engines not originally designed/manufactured by Briggs & Stratton to operate on

such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or re-

assembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or excessive

v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment controls,

etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or unbalanced

cutter blades or impellers, or improper coupling of equipment components to the

crankshaft;

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of equipment,

or improper engine installation.

WarrantyserviceisavailableonlythroughBriggs&StrattonAuthorizedService

Dealers.LocateyournearestAuthorizedServiceDealerinourdealerlocatormap

atBRIGGSandSTRATTON.COMorbycalling1-800-233-3723(inUSA).

80004537 (Rev. C)

Briggs&StrattonEmissionsWarranty

U.S.EPA,andBriggs&StrattonCorporationEmissionsControl

WarrantyStatementforEmergencyStandbyEngines-Your

WarrantyRightsandObligations

GeneralInformation

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the emissions control

system warranty on your Model Year 2017 - 2019 and later engine / equipment. In the

U.S., new Emergency Standby Engines must be designed, built, and equipped to meet

stringent emission standards. Engines less than 25 Hp must meet requirements of 40 CFR

Part 1054. Engines greater than 25 Hp and less than 130 Hp must meet requirements of

40 CFR Part 1048. B&S must warrant the emissions control system on your engine /

equipment.

See Definition of appropriate use of Emergency Standby below.

The emission-related warranty covers all components whose failure would increase an

engine's non-evaporative emissions of any regulated pollutant referenced below.

Manufacturer'sWarrantyCoverage:

Briggs & Stratton warrants that the engine is free from defects in material and workmanship,

and is also designed, built, and equipped to conform to applicable regulations under Section

213 of the Clean Air Act, from the time the engine is sold, until the expiration of its warranty

period.

This warranty applies to all emission related engine components whose failure would cause

engine exhaust emissions to be out of EPA compliance. Further, this warranty also applies

to other engine components damaged due to the failure of any of these emissions related

components.

If a warrantable emissions related component on your engine is defective, the part will be

repaired or replaced by B&S at no cost to you including diagnosis, parts, and labor.

Not for

Reproduction

Warranty coverage period is four years from date of original purchase, and is offered to

the original purchaser and each subsequent purchaser so long as Owner's Warranty

Responsibilities are adhered to.

Owner's Warranty Responsibilities:

• Warranty claims shall be filed according to the provisions of the Briggs & Stratton

Warranty Policy.

• An engine may not be warrantable if subjected to abuse, misuse, neglect, improper

maintenance, unapproved modifications, accidents not caused by Briggs & Stratton

engines or equipment, or by acts of God.

• Only those engines used as an Emergency Stationary Engine, as defined below, are

warrantable.

• You are responsible for presenting your engine / equipment to a B&S distribution

center, servicing dealer, or other equivalent entity, as applicable, as soon as a problem

exists. The warranty repairs should be completed in a reasonable amount of time,

not to exceed 30 days. If you have any questions regarding your warranty rights and

responsibilities, you should contact B&S at 1-800-444-7774 or

BRIGGSandSTRATTON.COM.

• If any components not scheduled for maintenance is repaired or replaced under this

warranty, the new part will be warranted only for the remaining warranty period.

• If a warrantable component scheduled for maintenance fails prior to its first scheduled

replacement, the part will be repaired or replaced by B&S at no charge to the owner.

Any such component is only warrantable until the originally scheduled maintenance

period has expired.

• Add on or modified parts that are not exempted by the EPA may not be used. The

use of any non-exempted add on or modified parts by the owner will be grounds for

disallowing a warranty claim. The manufacturer will not be liable to warrant failures

or warranted parts caused by the use of a non-exempted add on or modified part.

EmergencyStationaryEngineDefinition

An Emergency Stationary Engine is defined as any stationary internal combustion engine

whose operation is limited to emergency situations and required testing and maintenance.

Examples include stationary engines used to produce power for critical networks or

equipment (including power supplied to portions of a facility) when electric power from the

local utility (or the normal power source, if the facility runs on its own power production) is

interrupted, or stationary engines used to pump water in the case of fire or flood, etc.

Stationary engines used for peak shaving are not considered emergency stationary engines.

Stationary engines used to supply power to an electric grid or that supply power as part

of a financial arrangement with another entity are not considered to be emergency engines.

Emergency stationary ICE may be operated for the purpose of maintenance checks and

readiness testing, provided that the tests are recommended by Federal, State or local

government, the manufacturer, the vendor, or the insurance company associated with the

engine. Maintenance checks and readiness testing of such units is limited to 100 hours

per year. There is no time limit on the use of emergency stationary engines in emergency

situations. The owner or operator may petition the Administrator for approval of additional

hours to be used for maintenance checks and readiness testing, but a petition is not required

if the owner or operator maintains records indicating that Federal, State, or local standards

require maintenance and testing of emergency ICE beyond 100 hours per year. Emergency

stationary ICE may operate up to 50 hours per year in non-emergency situations, but those

50 hours are counted towards the 100 hours per year provided for maintenance and testing.

The 50 hours per year for non-emergency situations cannot be used for peak shaving or

to generate income for a facility to supply power to an electric grid or otherwise supply

power as part of a financial arrangement with another entity. For owners and operators of

emergency engines, any operation other than emergency operation, maintenance and

testing, and operation in non-emergency situations for 50 hours per year, as permitted

above is prohibited.

80015464 (Rev.C)

10 VanguardEngines.com

Not for

Reproduction

Това ръководство съдържа сведения за безопасна работа, за да сте наясно с авариите

и опасностите, свързани с тези двигатели и как да ги избягвате. То съдържа и

инструкции за правилната им употреба и поддръжка. Тъй като в Корпорация Briggs&

Stratton не биха могли да знаят каква машина ще се задвижва с този двигател, важно

е да прочетете и разберете тези инструкции u инструкциите за задвижваната машина.

Запишете тези оригинални инструкции за бъдещи справки.

Забележка:

Фигурите и илюстрациите в това ръководство са дадени само за справка

и могат да се различават от вашия специфичен модел. Свържете се с вашия

дистрибутор, ако имате въпроси.

За да получите резервни части или техническа помощ в бъдеще, запишете тук

модела, типа и кодовия номер на двигателя си заедно с датата на закупуването му

Тези номера са поставени върху вашия двигател (вижте раздел

Характеристики и

управления

Дата на купуване

Модел на двигателя - Вид - Настройка

Сериен номер на двигателя

Търсете двукоординатен баркод (2D),

поставен на някои двигатели. Когато се

разчита с 2D-четящо устройство, кодът ще

ви даде нашата Интернет страница, където

можете да имате достъп до информация

за поддръжка на този продукт. Въвеждане

на данни. В някои страни е възможно да

няма он-лайн достъпна информация за

поддръжка.

Информация за рециклиране

Всичките опаковки, отработилото масло и акумулаторите

трябва да бъдат рециклирани според действащите

правителствени постановления.

Безопасност на оператора

Предупредителни символи за

безопасност и предупредителни думи

Предупредителният символ за безопасност се използва за обозначаване на

информацията за безопасност, свързани с опасности, които могат да доведат до

нараняване. Предупредителните думи (ОПАСНОСТ, ПРЕДУПРЕЖДЕНИЕ или

ВНИМАНИЕ) се използват заедно с предупредителен символ, за да обозначат

вероятността и потенциалната тежест на нараняването. Предупредителен символ

за безопасност може да се използва, за да покаже типа на опасността.

ОПАСНО посочва опасност, която, ако не бъде избегната, ще доведе до смърт

или сериозно нараняване.

ПРЕДУПРЕЖДЕНИЕ посочва опасност, която, ако не бъде избегната, може да

доведе до смърт или сериозно нараняване.

ВНИМАНИЕ посочва опасност, която, ако не бъде избегната, би могла да

доведе до малка или средна степен на нараняване.

ПРЕДУПРЕЖДЕНИЕ

посочва ситуация, която би могла да доведе до повреждане

на продукта.

Символи за опасности и техните

значения

ЗначениеСимволЗначениеСимвол

Прочетете и разберете

Ръководството за оператора,

преди да работите или

правите техническо

обслужване на агрегата.

Информация по техника

на безопасност относно

рискове, които могат да

причинят нещастен

случай.

Опасност от взривОпасност от пожар

Опасност от токсични

изпарения

Опасност от ударно

въздействие

Опасност от висок шум - При

продължително ползване се

препоръчва защита на слуха.

Опасност от нагорещена

повърхност

Опасност от взривОпасност от изхвърляне

на предмет - Носете

защитни очила.

Опасност от откат (обратен

удар)

Опасност от

обледеняване

Опасност от химикалиОпасност от отрязване на

крайник - движещи се

части

КорозивенОпасност от топлинно

въздействие

Съобщения за безопасност

ПРЕДУПРЕЖДЕНИЕ

Някои от съставните елементи на този продукт и свързаните с него

приспособления съдържат химични вещества, известни в щата Калифорния като

причинители на рак, увреда на новородените или друга увреда на репродуктивната

способност. След работа с тях, измивайте ръцете си.

ПРЕДУПРЕЖДЕНИЕ

Изгорелите газове от този двигател съдържат химически съединения, известни

на щата Калифорния като причинители на рак, увреждания при раждане, или

други увреждания, свързани с репродуктивността.

ПРЕДУПРЕЖДЕНИЕ

Двигателите на Briggs & Stratton не са проектирани и не трябва да се използват

за задвижване на: увеселителни автомобили; на картинги; на детски автомобили,

на транспортни средства за разходка или транспортни средства с висока

проходимост (ATV); на мотоциклети; на транспортни средства на въздушна

възглавница; на летателни апарати; или на превозни средства, използвани за

участие в състезателни мероприятия, неразрешени от Briggs & Stratton. За

информация относно изделия за състезателни цели вижте www.briggsracing.com.

При използване на превозни средства с общо предназначение и такива с

повишена проходимост (ATV), моля свържете се с Приложния център за двигатели

на Briggs & Stratton на тел. 1-866-927-3349. Неправилното приложение на

двигателя може да причини нещастен случай или смърт.

Not for

Reproduction

ПРЕДУПРЕЖДЕНИЕ

Този двигател се доставя от Briggs& Stratton без масло. Преди да стартирате

двигателя се уверете, че сте налели масло в него според инструкциите в

настоящото ръководство. Ако го стартирате без масло, той ще се повреди, без

да бъде възможно да се ремонтира и без покритие от гаранцията.

ПРЕДУПРЕЖДЕНИЕ

Газообразните изпарения са изключително запалими и взривоопасни.

Пожар или взрив могат да причинят сериозни обгаряния или смърт.

При доливане на гориво

• Пълнете резервоара за гориво на открито или в добре проветриво помещение.

• Проверявайте често горивопроводите, резервоара, капачката и съединенията

за пукнатини и течове. Заменете ги, ако е необходимо.

При стартиране на двигателя

• Уверете се, че запалителната свещ, шумозаглушителя, капачката на

резервоара за гориво и въздушния филтър (ако има такива) са на мястото си

и са обезопасени.

• Не развъртайте двигателя с извадена запалителна свещ.

При работеща машина

• Никога не стартирайте и не работете с двигателя при отстранен комплект на

въздушния филтър (ако има такъв) или при отстранен въздушен филтър (ако

има такъв).

При транспортиране на машината

• Двигателите, работещи с природен газ/втечнен нефтен газ да се транспортират

с празен горивен резервоар или със затворен кран, или изолиран резервоар

за горивото.

При складиране на гориво или на машина с гориво в резервоара

• Складирайте далеч от пещи, печки, водонагреватели или други електрически

прибори, които имат сигнални лампи или други запалителни източници, защото

те могат да възпламенят изпаренията от горивото.

ПРЕДУПРЕЖДЕНИЕ

Пускането на двигателя създава искрене.

Искренето може да възпламени намиращите се наоколо запалими газове.

Това може да доведе до експлозия и пожар.

• Ако има изтичане на природен или втечнен газ пропан в помещението, не

палете двигателя.

• Не използвайте горива за начално запалване под налягане, защото парите

им са запалими.

ПРЕДУПРЕЖДЕНИЕ

ОПАСНОСТ ОТ ОТРОВНИ ГАЗОВЕ. Отработилите газове от двигателя

съдържат въглероден оксид, отровен газ, който би могъл да ви убие за

минути. Вие НЕ МОЖЕТЕ да го видите, да го помиришете или вкусите. Дори

ако не можете да помиришете отработилите газове, вие, все още, може да

бъдете изложени на въздействието на въглеродния оксид. Ако започнете

да се чувствате зле, объркан или отслабнал, докато ползвате това изделие,

излезте ВЕДНАГА на свеж въздух. Отидете на лекар. Възможно е да сте

получили отравяне от въглероден оксид.

• Работете с този продукт САМО на открито, далеко от прозорци, врати и

вентилационни отвори, за да намалите опасността от натрупване на

въглероден окис и от потенциалното му насочване към помещения с хора.

• Монтирайте сигнални уредби за въглероден оксид, захранвани с батерии или

с такива, включващи се от появата му, според инструкциите на производителя.

Сигналните уредби за димни газове не могат да откриват въглеродния оксид.

• НЕ ПУСКАЙТЕ този продукт вътре в домове, гаражи, сутерени, непреходни

коридори, хангари или други частично затворени помещения, дори при

използване на вентилатори или отворени врати и прозорци за вентилация.

Въглеродният оксид може бързо да се натрупа в тези помещения и да се

задържи в продължение на часове, дори след като този продукт е изключен.

• ВИНАГИ поставяйте този продукт по посока на въздушното течение и

насочвайте отработилите димни газове надалеко от заетите с хора помещения.

ПРЕДУПРЕЖДЕНИЕ

Бързото притегляне на пусковото въже (обратен удар) придърпва ръката

към двигателя по-бързо, отколкото вие можете да я отдръпнете.

Това може да причини счупени кости, фрактури, контузии и навяхвания.

• При стартиране на двигателя изтеглете бавно пусковото въже, докато

почувствате съпротивление, след което го дръпнете рязко, за да избегнете

обратния удар.

• Изключете всички външни приспособления, които двигателят задвижва, преди

да го стартирате.

• Директно прикачените към двигателя машинни елементи като ножове, перки,

лебедки, зъбни колела, задвижващи вериги и други, трябва да бъдат сигурно

прикрепени.

ПРЕДУПРЕЖДЕНИЕ

Въртящите се части могат да допрат или захванат ръце, крака, коса, облекло

или принадлежности.

Може да се достигне до травматична ампутация или сериозно нараняване.

• Работете с двигателя при поставени защитни капаци.

• Дръжте ръцете и краката си на разстояние от въртящите се части.

• Привързвайте дългите коси и сваляйте украшенията.

• Не носете по себе си широко облекло, висящи шнурове или вещи, които могат

да бъдат захванати.

ПРЕДУПРЕЖДЕНИЕ

Работещите двигатели отделят топлина. Частите на двигателите, особено

шумозаглушителя, стават изключително горещи.

При допир може да получите сериозно изгаряне.

Горимите отпадъци, като листа, треви, храсталак и други, могат да се

запалят.

• Оставете шумозаглушителя, цилиндъра на двигателя и ребрата да се охладят,

преди да ги докосвате.

• Отстранете натрупаните отломки около шумозаглушителя и цилиндъра.

• Използването или работата с двигателя, по залесени с гори, храсти или с

треви площи, според Правилника на Калифорния за обществените ресурси,

Раздел 4442, представлява нарушение, освен ако двигателят не е снабден с

искрогасител, поддържан в ефикасно работно състояние, както е определено

в Раздел 4442 В другите щати и федерални юрисдикции може да има подобни

закони. Влезте във връзка с производителя на оригиналното оборудване, с

продавача на дребно или дилъра, за да си набавите искрогасител, проектиран

за изпускателната система на този двигател.

ПРЕДУПРЕЖДЕНИЕ

Случайно искрене може да доведе до пожар или поразяване от електрически

ток.

Неволно стартиране може да доведе до захващане, травматична ампутация

или до раняване.

Опасност от пожар

Преди извършване на регулировки и поправки:

• Откачете кабела на запалителната свещ и го дръжте далеч от нея.

• Откачете минус-клемата на акумулатора (само при двигатели с електрически

стартер).

• Използвайте само подходящи инструменти.

• Не застопорявайте с регулираща пружина, лостчета или други части, за да

повишавате оборотите на двигателя.

• Резервните части трябва да бъдат със същата конструкция и да се монтират

в същото положение, както оригиналните части. Части от друг производител

може да не работят добре, може да повредят агрегата или да доведат до

нараняване.

• Не удряйте маховика с чук или твърд предмет, защото той може да се строши

по време на работа.

12 VanguardEngines.com

Not for

Reproduction

При изпробване за искра:

• Използвайте одобрен тип тестер за свещи.

• Не проверявайте за искра при извадена свещ.

ПРЕДУПРЕЖДЕНИЕ

Газообразните горива са изключително запалими и лесно образуват взривни

въздушно-парови смеси при околните температури.

Ако ви замирише на газ:

• Не стартирайте двигателя.

• Не включвайте, който и да е от електрическите ключове.

• Не използвайте телефон в непосредствена близост.

• Напуснете мястото.

• Свържете се с доставчика на газ или противопожарната служба.

ПРЕДУПРЕЖДЕНИЕ

Носете защитни очила при извършване на ремонтни работи.

При контакт на кожа/око с втечнен пропан може да се получи местно

измръзване.

• Монтажните, регулировъчните и ремонтните работи трябва да се извършват

от квалифициран техник.

• Редовно проверявайте захранващия гъвкав маркуч Уверете се, че е в добро

състояние. Сменявайте повредените или течащите елементи.

ПРЕДУПРЕЖДЕНИЕ

Липсващ или неработещ, „изключващ горивото“ кран може да причини

пожар или взрив.

• Не работете с оборудването, ако „изключващ горивото“ кран липсва или не

работи.

Елементи и управления

Управления на двигателя

Сравнете илюстрацията (фигура: 1, 2, 3) с вашия двигател, за да се запознаете с

разположението на различните елементи и управления.

A. Идентификационни номера на двигателя Модел - Тип - Код

B. Запалителна свещ

C. Въздушен филтър

D. Нивопоказател

E. Маслен филтър (ако има такъв)

F. Пробка за източване на маслото

G. Сензор за налягането на маслото

H. Решетка на отвора за въздух

I. Електрически стартер

J. Ръчно стартиране (ако има такова)

K. Смесител на втечнен нефтен газ/природен газ

L. Изпускателна тръба

M. Шумозаглушител (ако има такъв)

N. Маслен радиатор (ако има такъв)

Символи за управление и значенията

им

ЗначениеСимволЗначениеСимвол

Обороти на двигателя - Slow

(Бавни)

Обороти на двигателя -

Fast (Бързи)

On - Off (Вкл. - Изкл.)Обороти на двигателя -

Stop (Спрян)

Работа

Препоръки за маслото

Вместимост на масло: Вижте

Раздел Спецификации на

маслото.

ПРЕДУПРЕЖДЕНИЕ

Този двигател се доставя от Briggs & Stratton без масло. Производителите на

оборудването или търговците може да са добавили масло в двигателя Преди да

стартирате двигателя за първи път, се уверете, че сте проверили и добавили

масло в него според инструкциите в настоящото ръководство. Ако стартирате

двигателя без масло, той ще се повреди, без да бъде възможно да се ремонтира

и без покритие от гаранцията.

За най-добро представяне препоръчваме да се използват сертифицираните масла

с гаранция на Briggs & Stratton. Приемливи са и други висококачествени прочистващи

масл а от клас SF, SG, SH, SJ или по-висок. Не използвайте специални добавки.

Външните температури определят правилния вискозитет на маслото за двигателя.

Използвайте таблицата, за да изберете най-добрия вискозитет според очаквания

диапазон на външната температура. Двигателите на по-голямата част от

оборудването с външно захранване работят добре със синтетично масло 5W-30. За

оборудване, което се използва при високи температури, синтетичното масло

Vanguard™ 15W-50 осигурява най-добра защита.

SAE 30 - При температури под 40°F (4°C) употребата на SAE 30 ще доведе

до трудно стартиране.

10W-30 - При температури над 80°F (27°C) употребата на 10W-30 може да

предизвика повишен разход на масло. Проверявайте нивото на маслото по-

често.

5W-30C

Синтетично масло 5W-30D

Vanguard™ Synthetic 15W-50E

Проверка и доливане на масло

Вижте Фигура: 4

Преди проверка или доливане на масло

• Уверете се, че двигателят е разположен хоризонтално.

• Почистете мястото около отвора за наливане на масло от отпадъци.

• Вижте

Раздел Спецификации

за вместимост на маслото.

Not for

Reproduction

ПРЕДУПРЕЖДЕНИЕ

Този двигател се доставя от Briggs & Stratton без масло. Производителите на

оборудването или търговците може да са добавили масло в двигателя. Преди да

стартирате двигателя за първи път се уверете, че сте проверили и налели масло

в него, според инструкциите в настоящото ръководство. Ако стартирате двигателя

без масло, той ще се повреди, без да бъде възможно да се ремонтира и без

покритие от гаранцията.

Раздел Проверка на нивото на маслото

1. Свалете щеката на нивопоказателя (A, Фигура 4) и я подсушете с чиста кърпа.

2. Поставете и затегнете щеката на нивопоказателя (A, Фигура 4).

3. Свалете щеката на нивопоказателя и проверете нивото на маслото. Коригирайте

нивото на маслото до горната част на индикатора за напълване (B, Фигура 4)

върху нивопоказателя.

Долейте масло

1. Ако нивото на маслото е ниско, внимателно долейте през отвора за наливане

на масло (C, Фигура ). 4). Не препълвайте. След доливане на масло, изчакайте

една минута и след това проверете отново нивото му.

2. Поставете и затегнете отново щеката на нивопоказателя (A, Фигура ). 4).

Система за защита при ниско ниво на

маслото (ако има такава)

Някои двигатели са оборудване с датчик за ниско ниво на маслото. Ако нивото на

маслото е ниско, датчикът или ще включи сигнален индикатор или ще спре двигателя.

Спрете двигателя и следвайте тези етапи, преди да го пуснете отново.

• Уверете се, че двигателят е хоризонтално разположен.

• Проверете нивото на маслото Направете справка в раздела

Проверка на

нивото на маслото

• Ако нивото на маслото е ниско, долейте съответното количество масло. Пуснете

двигателя и се уверете, че предупредителният индикатор (ако има такъв) не е

задействан.

• Ако нивото на маслото е ниско, не пускайте двигателя. Свържете се с

Оторизиран сервизен представител на Briggs & Stratton за отстраняване на

проблема с маслото.

Препоръки за горивото

ПРЕДУПРЕЖДЕНИЕ

Липсващ или неработещ, „изключващ горивото“ кран може да причини пожар

или взрив.

• Не работете с оборудването, ако „изключващи горивото“ кран липсва или не

работи.

Горивото трябва да отговаря на следните изисквания

• Използвайте чисто, обезводнено гориво, без влага или някакви материални

частици. Използване на горива без спазване на препоръчваните качества може

да причини проблеми с техническите характеристики.

• За двигатели, регулирани да работят с втечнен нефтен газ, се препоръчва

търговската марка HD5 LPG. Препоръчваният състав на горивото е този, който

има минимален специфичен термодинамичен потенциал по обем, от минимум

93150 kJ/m (2500 BTU’s/ft³) с 5% максимално съдържание на пропилен, с 2,5%

съдържание на бутан и по-тежки газове и с 90% минимално съдържание на

пропан.

Двигателите за природен газ или втечнен нефтен газ са сертифицирани да работят

с природен или втечнен газ пропан. Системата за контрол над вредните емисии за

двигателя е тип EM (Модификации на двигателя).

ПРЕДУПРЕЖДЕНИЕ

Оборудването, към което този двигател се монтира, е снабдено с автоматичен,

предпазен, „изключващ горивото“ кран. Не работете с оборудването, ако

„изключващ горивото“ кран липсва или не работи.

Доливане на гориво

ПРЕДУПРЕЖДЕНИЕ

Газообразните изпарения са изключително запалими и взривоопасни.

Пожар или взрив могат да причинят сериозни обгаряния или смърт.

При доливане на гориво

• Пълнете резервоара за гориво на открито или в добре проветриво помещение.

• Проверявайте често горивопроводите, резервоара, капачката и съединенията

за пукнатини и течове. Да се сменяват, ако е необходимо.

За информация относно зареждането на двигатели с природен газ и втечнен нефтен

газ прочетете работните инструкции, предоставени от производителя на

оборудването.

Стартиране и спиране на двигателя

Вижте фигура: 5

Стартиране на двигателя

ПРЕДУПРЕЖДЕНИЕ

Бързото притегляне на пусковото въже (обратен удар) придърпва ръката

към двигателя по-бързо, отколкото вие можете да я отдръпнете.

Това може да причини счупени кости, фрактури, контузии и навяхвания.

• При стартиране на двигателя изтеглете бавно пусковото въже, докато

почувствате съпротивление, след което го дръпнете рязко, за да избегнете

обратния удар.

ПРЕДУПРЕЖДЕНИЕ

Газообразните изпарения са изключително запалими и взривоопасни.

Пожар или взрив могат да причинят сериозни обгаряния или смърт.

При стартиране на двигателя

• Уверете се, че запалителната свещ, шумозаглушителя, въздушния филтър (ако

има такъв) са на мястото си и са добре закрепени.

• Не развъртайте двигателя с извадена запалителна свещ.

ПРЕДУПРЕЖДЕНИЕ

ОПАСНОСТ ОТ ОТРОВНИ ГАЗОВЕ. Отработилите газове от двигателя

съдържат въглероден оксид, отровен газ, който би могъл да ви убие за

минути. Вие НЕ МОЖЕТЕ да го видите, да го помиришете или вкусите. Дори

ако не можете да помиришете отработилите газове, вие, все още, може да

бъдете изложени на въздействието на въглеродния оксид. Ако започнете

да се чувствате зле, объркан или отслабнал, когато ползвате това изделие,

излезте ВЕДНАГА на чист въздух. Отидете на лекар. Възможно е да сте

получили отравяне от въглероден оксид.

• Работете с този продукт САМО на открито, далеко от прозорци, врати и

вентилационни отвори, за да намалите опасността от натрупване на въглероден

окис и от потенциалното му насочване към помещения с хора.