Makita HR001G Kullanım kılavuzu

HR001G

HR002G

HR003G

HR004G

EN Cordless Combination

Hammer INSTRUCTION MANUAL 11

FR Marteau Combiné sans Fil MANUEL D’INSTRUCTIONS 25

DE Akku-Kombi-Bohrhammer BETRIEBSANLEITUNG 40

IT Tassellatore combinato a

batteria ISTRUZIONI PER L’USO 57

NL Accucombihamer GEBRUIKSAANWIJZING 74

ES Martillo Rotativo Combinado

Inalámbrico

MANUAL DE

INSTRUCCIONES 90

PT Martelete Combinado A

Bateria MANUAL DE INSTRUÇÕES 107

DA Akku-kombinationshammer BRUGSANVISNING 123

EL Φορητό δράπανο

συνδυασμού ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ 137

TR Kablosuz Kombine Darbeli

Matkap KULLANMA KILAVUZU 154

1

2

3

Fig.1

1

2

Fig.2

1

Fig.3

1

Fig.4

1

Fig.5

1

AB

Fig.6

1 2

3

Fig.7

1 2

3 4

Fig.8

2

1

2

Fig.9

1

Fig.10

1

Fig.11

1

Fig.12

Fig.13

1

2

3

Fig.14

1 2

Fig.15

3

1

Fig.16

1

A

Fig.17

1

Fig.18

1

Fig.19

1

2

Fig.20

1

Fig.21

1

2

Fig.22

1

Fig.23

4

3

4

1 2

Fig.24

Fig.25

1

Fig.26

1

Fig.27

2

1

Fig.28

1

Fig.29

1

2

Fig.30

5

Fig.31

Fig.32

Fig.33

Fig.34

1 2

Fig.35

1

2

Fig.36

2

1

Fig.37

1

Fig.38

6

1

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

1

Fig.44

3

1

4

2

Fig.45

7

1

2

3

Fig.46

1

Fig.47

12

Fig.48

Fig.49

1

Fig.50

8

12

Fig.51

1

Fig.52

1

Fig.53

12

Fig.54

1

Fig.55

2

1

Fig.56

9

1

2

Fig.57

1

2

Fig.58

10

11 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: HR001G HR002G HR003G HR004G

Capacities Concrete 28 mm

Core bit 54 mm

Diamond core bit (dry type) 65 mm

Steel 13 mm

Wood 32 mm

No load speed 0 - 980 min-1

Blows per minute 0 - 5,000 min-1

Rated voltage D.C. 36 V - 40 V max

Overall length with BL4025 358 mm 389 mm 358 mm 389 mm

with BL4040 373 mm 404 mm 373 mm 404 mm

Net weight 3.9 - 4.6 kg 4.1 - 4.6 kg 3.9 - 4.6 kg 4.0 - 4.5 kg

Optional accessory

Model: DX12 (For HR001G/HR003G) DX14 (For HR002G/HR004G)

Suction performance 350 l/min

Operating stroke Up to 190 mm

Suitable drill bit Up to 260 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 1.6 kg

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may differ from country to country.

• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4025 / BL4040

Charger DC40RA

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Intended use

The tool is intended for hammer drilling and drilling in

brick, concrete and stone as well as for chiselling work.

It is also suitable for drilling without impact in wood,

metal, ceramic and plastic.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745-2-6:

Model HR001G

Sound pressure level (LpA) : 95 dB(A)

Sound power level (LWA) : 106 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR002G

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR003G

Sound pressure level (LpA) : 95 dB(A)

Sound power level (LWA) : 106 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR004G

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR001G with DX12

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR002G with DX14

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

12 ENGLISH

Model HR003G with DX12

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR004G with DX14

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE:

The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE:

The declared noise emission value(s) may

also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can differ from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched off and when

it is running idle in addition to the trigger time).

Vibration

The following table shows the vibration total value (tri-axial

vector sum) determined according to applicable standard.

Model HR001G

Work mode Vibration

emission

Uncertainty (K)

Applicable

standard

Hammer

drilling into

concrete

(ah, HD)

7.0 m/s21.5 m/s2EN60745-2-6

Hammer

drilling into

concrete with

DX12 (ah, HD)

7.0 m/s21.5 m/s2EN60745-2-6

Chiselling func-

tion with side

grip (ah, Cheq)

6.5 m/s21.5 m/s2EN60745-2-6

Drilling into

metal (ah, D)

2.5 m/s2 or

less

1.5 m/s2EN60745-2-1

Model HR002G

Work mode Vibration

emission

Uncertainty (K)

Applicable

standard

Hammer

drilling into

concrete

(ah, HD)

6.5 m/s21.5 m/s2EN60745-2-6

Hammer

drilling into

concrete with

DX14 (ah, HD)

6.0 m/s21.5 m/s2EN60745-2-6

Chiselling func-

tion with side

grip (ah, Cheq)

7.5 m/s21.5 m/s2EN60745-2-6

Drilling into

metal (ah, D)

2.5 m/s21.5 m/s2EN60745-2-1

Model HR003G

Work mode Vibration

emission

Uncertainty (K)

Applicable

standard

Hammer

drilling into

concrete

(ah, HD)

7.0 m/s21.5 m/s2EN60745-2-6

Hammer

drilling into

concrete with

DX12 (ah, HD)

7.0 m/s21.5 m/s2EN60745-2-6

Chiselling func-

tion with side

grip (ah, Cheq)

7.0 m/s21.5 m/s2EN60745-2-6

Drilling into

metal (ah, D)

2.5 m/s2 or

less

1.5 m/s2EN60745-2-1

Model HR004G

Work mode Vibration

emission

Uncertainty (K)

Applicable

standard

Hammer

drilling into

concrete

(ah, HD)

6.5 m/s21.5 m/s2EN60745-2-6

Hammer

drilling into

concrete with

DX14 (ah, HD)

6.0 m/s21.5 m/s2EN60745-2-6

Chiselling func-

tion with side

grip (ah, Cheq)

7.5 m/s21.5 m/s2EN60745-2-6

Drilling into

metal (ah, D)

2.5 m/s21.5 m/s2EN60745-2-1

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can differ from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

off and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

13 ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

CORDLESS ROTARY HAMMER

SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can

cause hearing loss.

2. Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

3.

Hold power tool by insulated gripping sur-

faces, when performing an operation where the

cutting accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before

operation.

6.

Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

a while by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difcult.

8. Always be sure you have a rm footing. Be

sure no one is below when using the tool in

high locations.

9. Hold the tool rmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area

when operating. The bit could y out and

injure someone seriously.

13.

Do not touch the bit, parts close to the bit, or

workpiece immediately after operation; they

may be extremely hot and could burn your skin.

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

15.

Always be sure that the tool is switched off and

the battery cartridge and the bit are removed

before handing the tool to other person.

16. Before operation, make sure that there is no

buried object such as electric pipe, water pipe

or gas pipe in the working area. Otherwise, the

drill bit/chisel may touch them, resulting an electric

shock, electrical leakage or gas leak.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2.

Do not disassemble or tamper the battery cartridge.

It may result in a re, excessive heat, or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current ow,

overheating, possible burns and even a breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consulting an

expert for hazardous material is required. Please also

observe possibly more detailed national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

14 ENGLISH

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near a

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1.

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the

battery cartridge when you notice less tool power.

2.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the wire-

less unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50°C (122°F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart

pace makers are nearby.

7.

Do not operate the wireless unit in places where

automated devices are nearby. If operated, auto-

mated devices may develop malfunction or error.

8. Do not operate the wireless unit in places

under high temperature or places where

static electricity or electrical noise could be

generated.

9. The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the

user.

10. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

14. Always insert the wireless unit in the correct

direction.

15. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

16. Always close the lid of the slot when

operating.

17. Do not remove the wireless unit from the slot

while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless

unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where

static electricity or electrical noise could be

generated.

21. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the

sun.

22. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas

could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

27. Do not use the tool with the lid of the slot dam-

aged. Water, dust, and dirt come into the slot may

cause malfunction.

28. Do not pull and/or twist the lid of the slot more

than necessary. Restore the lid if it comes off

from the tool.

29. Replace the lid of the slot if it is lost or

damaged.

SAVE THESE INSTRUCTIONS.

15 ENGLISH

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip off your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► Fig.2: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

the tool off and stop the application that caused the tool

to become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically. In this case, let the tool and battery cool

before turning the tool on again.

NOTE: When the tool is overheated, the lamp blinks.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Switch action

WARNING:

Before installing the battery cartridge into

the tool, always check to see that the switch trigger actuates

properly and returns to the "OFF" position when released.

► Fig.3: 1. Switch trigger

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Speed change

The revolutions and blows per minute can be adjusted

by turning the adjusting dial. The dial is marked 1 (low-

est speed) to 5 (full speed).

► Fig.4: 1. Adjusting dial

Refer to the table below for the relationship between the number

on the adjusting dial and the revolutions and blows per minute.

Number Revolutions per

minute

Blows per minute

5980 5,000

4870 4,440

3630 3,210

2380 1,940

1300 1,530

CAUTION: Do not turn the adjusting dial when

the tool is running. Failure to do so may result in

the loss of control of the tool and cause an injury.

16 ENGLISH

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: The speed adjusting dial can be turned

only as far as 5 and back to 1. Do not force it past

5 or 1, or the speed adjusting function may no

longer work.

NOTE: Soft no-load rotation function (For

HR001G/HR002G)

When the speed adjusting dial is set to "4" or higher,

the tool automatically reduces the speed at no-load to

reduce the vibration under no-load. Once operation

starts with a bit against concrete, blows per minute

increase and reach the numbers as shown in the

table. When temperature is low and there is less

uidity in grease, the tool may not have this function

even with the motor rotating.

Lighting up the front lamp

► Fig.5: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 10 seconds after

releasing the switch trigger.

CAUTION: For HR001G/HR002G

If the lamp goes off after blinking for a few sec-

onds, the active feedback sensing technology

is not working properly. Ask your local Makita

Service Center for repair.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: If the dust collection system is installed on the

tool, the lamp of the dust collection system lights up

instead of the lamp of the tool.

Reversing switch action

► Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Changing the quick change chuck

for SDS-plus

For HR002G/HR004G

The quick change chuck for SDS-plus can be easily

exchanged for the quick change drill chuck.

Removing the quick change chuck

for SDS-plus

CAUTION: Before removing the quick change

chuck for SDS-plus, be sure to remove the bit.

Grasp the change cover of the quick change chuck for

SDS-plus and turn in the direction of the arrow until

the change cover line moves from the symbol to

the symbol. Pull forcefully in the direction of the arrow.

► Fig.7: 1. Quick change chuck for SDS-plus

2. Change cover 3. Change cover line

Installing the quick change drill chuck

Check the line of the quick change drill chuck shows

the symbol. Grasp the change cover of the quick

change drill chuck and set the line to the symbol.

Place the quick change drill chuck on the spindle of the

tool. Grasp the change cover of the quick change drill

chuck and turn the change cover line to the symbol

until a click can clearly be heard.

► Fig.8: 1. Quick change drill chuck 2. Spindle

3. Change cover line 4. Change cover

Selecting the action mode

NOTICE:

Do not rotate the action mode changing

knob when the tool is running. The tool will be damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the three action mode positions.

Rotation with hammering

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a tungsten-

carbide tipped bit (optional accessory).

► Fig.9: 1. Rotation with hammering 2. Action mode

changing knob

Rotation only

For drilling in wood, metal or plastic materials, rotate

the action mode changing knob to the symbol. Use a

twist drill bit or wood drill bit.

► Fig.10: 1. Rotation only

Hammering only

For chipping, scaling or demolition operations, rotate

the action mode changing knob to the symbol. Use a

bull point, cold chisel, scaling chisel, etc.

► Fig.11: 1. Hammering only

17 ENGLISH

Hook

CAUTION: Always remove the battery when

hanging the tool with the hook.

CAUTION: Never hook the tool at high loca-

tion or on potentially unstable surface.

The hook is convenient for temporarily hanging the tool.

To use the hook, simply lift up hook until it snaps into

the open position. When not in use, always lower hook

until it snaps into the closed position.

► Fig.12: 1. Hook

► Fig.13

Connecting lanyard (tether strap) to

the hook

CAUTION: Do not use damaged hook and

screws. Before use, always check for damages,

cracks or deformations, and make sure that the

screws are tightened.

CAUTION: Make sure that the hook is

securely installed with the screws.

CAUTION: Do not remove the battery car-

tridge while hanging the tool. The tool may fall if the

screws are not tightened.

CAUTION: Always use a locking carabiner

(multi-action and screw gate type) and be sure

to attach the lanyard (tether strap) to the double

looped portion of the hook. Improper attachment

may cause tool drop from the hook and result in

personal injury.

The hook is also used for connecting the lanyard (tether

strap). Be sure to connect the lanyard (tether strap) to

the double looped portion of the hook.

► Fig.14: 1. Double looped portion of the hook

2. Lanyard (tether strap) 3. Locking cara-

biner (multi-action and screw gate type)

Adjusting the nozzle position of the

dust collection system

Optional accessory

Push in the guide while pushing up the guide adjust-

ment button, and then release the button at the desired

position.

► Fig.15: 1. Guide 2. Guide adjustment button

NOTE: Before adjusting the nozzle position, release

the nozzle forward completely by pushing up the

guide adjustment button.

If a long drill bit is installed, extend the guide by pushing

up the extension button.

► Fig.16: 1. Extension button

Adjusting the drilling depth of the

dust collection system

Optional accessory

Slide the depth adjustment button to the desired posi-

tion while pushing it up. The distance (A) is the drilling

depth.

► Fig.17: 1. Depth adjustment button

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch off the tool immediately. This will help pre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool. This is because they will cause

the torque limiter to actuate too frequently.

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the drill bit will stop

turning.

Electronic function

The tool is equipped with the electronic functions for

easy operation.

• Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

• Active Feedback sensing Technology (For

HR001G/HR002G)

If the tool is swung at the predetermined accelera-

tion during operation, the motor is forcibly stopped

to reduce the burden on the wrist.

NOTE: This function does not work if the acceleration

does not reach the predetermined one when the tool

is swung.

NOTE: If the bit is swung at the predetermined

acceleration during chipping, scaling, or demolishing,

the motor is forcibly stopped. In this case, release

the switch trigger, and then pull the switch trigger to

restart the tool.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

18 ENGLISH

To install the side grip, follow the steps below.

1. Loosen the thumb screw on the side grip.

► Fig.18: 1. Thumb screw

2. Attach the side grip while pressing the thumb

screw so that the grooves on the grip t in the protru-

sions on the tool barrel.

► Fig.19: 1. Thumb screw

3. Tighten the thumb screw to secure the grip. The

grip can be xed at desired angle.

Grease

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

This chuck lubrication assures smooth action and lon-

ger service life.

Installing or removing drill bit

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

► Fig.20: 1. Shank end 2. Grease

Insert the drill bit into the tool. Turn the drill bit and push

it in until it engages.

After installing the drill bit, always make sure that the

drill bit is securely held in place by trying to pull it out.

► Fig.21: 1. Drill bit

To remove the drill bit, pull the chuck cover down all the

way and pull the drill bit out.

► Fig.22: 1. Drill bit 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

The chisel can be secured at the desired angle. To

change the chisel angle, rotate the action mode chang-

ing knob to the O symbol. Turn the chisel to the desired

angle.

► Fig.23: 1. Action mode changing knob

Rotate the action mode changing knob to the sym-

bol. Then make sure that the chisel is securely held in

place by turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of

uniform depth.

Press and hold the lock button, and then insert the

depth gauge into the hex hole. Make sure that the

toothed side of the depth gauge faces the marking.

► Fig.24: 1. Depth gauge 2. Lock button 3. Marking

4. Toothed side

Adjust the depth gauge by moving it back and forth

while pressing the lock button. After the adjustment,

release the lock button to lock the depth gauge.

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Installing or removing the dust

collection system

Optional accessory

To install the dust collection system, insert the tool into

the dust collection system all the way until it locks in

place with a little double click.

► Fig.25

To remove the dust collection system, pull the tool while

pressing the lock-off button.

► Fig.26: 1. Lock-off button

Dust cup

Optional accessory

Use the dust cup to prevent dust from falling over the tool and

on yourself when performing overhead drilling operations.

Attach the dust cup to the bit as shown in the gure. The size

of bits which the dust cup can be attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dust cup 9 12 mm - 16 mm

► Fig.27: 1. Dust cup

Dust cup set

Optional accessory

Before installing the dust cup set, remove the bit from

the tool if installed.

Install the dust cup set on the tool so that the sym-

bol on the dust cup is aligned with the groove in the tool.

► Fig.28: 1. symbol 2. Groove

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

► Fig.29: 1. Dust cap

To remove the dust cup set, remove the bit while pulling

the chuck cover in the direction of the arrow.

► Fig.30: 1. Bit 2. Chuck cover

Hold the root of dust cup and pull it out.

► Fig.31

NOTE: If the cap comes off from the dust cup, attach

it with its printed side facing up so that groove on the

cap ts in the inside periphery of the attachment.

► Fig.32

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

CAUTION:

Do not pull the tool out forcibly even

the bit gets stuck. Loss of control may cause injury.

19 ENGLISH

CAUTION: The dust collection system is

intended for drilling in concrete only. Do not use

the dust collection system for drilling in metal or

wood.

CAUTION: When using the tool with the dust

collection system, be sure to attach the lter

to the dust collection system to prevent dust

inhalation.

CAUTION: Before using the dust collection

system, check that the lter is not damaged.

Failure to do so may cause dust inhalation.

CAUTION: The dust collection system col-

lects the generated dust at a considerable rate,

but not all dust can be collected.

NOTICE: Do not use the dust collection system

for core drilling or chiseling.

NOTICE: Do not use the dust collection system

for drilling in wet concrete or use this system

in wet environment. Failure to do so may cause

malfunction.

NOTE: If the battery cartridge is in low temperature,

the tool’s capability may not be fully obtained. In this

case, warm up the battery cartridge by using the

tool with no load for a while to fully obtain the tool’s

capability.

► Fig.33

Hammer drilling operation

CAUTION: There is tremendous and sudden

twisting force exerted on the tool/drill bit at the time of

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

of the tool and potentially severe injury.

Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

while operating the tool with no load. The tool auto-

matically centers itself during operation. This does not

affect the drilling precision.

Chipping/Scaling/Demolition

Set the action mode changing knob to the symbol.

Hold the tool rmly with both hands. Turn the tool on

and apply slight pressure on the tool so that the tool will

not bounce around, uncontrolled.

Pressing very hard on the tool will not increase the efciency.

► Fig.34

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool. The

drill chuck may be damaged.

Also, the drill chuck will come off when reversing the tool.

NOTICE:

Pressing excessively on the tool will not

speed up the drilling. In fact, this excessive pressure will

only serve to damage the tip of your drill bit, decrease the

tool performance and shorten the service life of the tool.

Set the action mode changing knob to the symbol.

For HR001G/HR003G

Optional accessory

Attach the chuck adapter to a keyless drill chuck to

which 1/2"-20 size screw can be installed, and then

install them to the tool. When installing it, refer to the

section “Installing or removing drill bit”.

► Fig.35: 1. Keyless drill chuck 2. Chuck adapter

For HR002G/HR004G

Use the quick change drill chuck as standard equip-

ment. When installing it, refer to "changing the quick

change chuck for SDS-plus".

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as

it will go. Hold the ring rmly and turn the sleeve clock-

wise to tighten the chuck.

► Fig.36: 1. Sleeve 2. Ring

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling opera-

tions, always set the action mode changing knob to

the position to use "rotation only" action.

20 ENGLISH

Beating dust on the lter

Optional accessory

CAUTION:

Do not turn the dial on the dust case

while the dust case is removed from the dust collec-

tion system. Doing so may cause dust inhalation.

CAUTION: Always switch off the tool when

turning the dial on the dust case. Turning the dial

while the tool is running may result in the loss of

control of the tool.

By beating the dust on the lter inside the dust case,

you can keep the vacuum efciency and also reduce

the number of times to dispose of the dust.

Turn the dial on the dust case three times after col-

lecting every 50,000 mm3 of dust or when you feel the

vacuum performance declined.

NOTE: 50,000 mm3 of dust equivalents to drilling 10

holes of ø10 mm and 65 mm depth (14 holes of ø3/8″

and 2″ depth).

► Fig.37: 1. Dust case 2. Dial

Disposing of dust

Optional accessory

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Be sure to wear dust mask when

disposing of dust.

CAUTION: Empty the dust case regularly

before the dust case becomes full. Failure to do so

may decrease the dust collection performance and

cause dust inhalation.

CAUTION: The performance of dust collection

decreases if the lter in the dust case become

clogged. Replace the lter with new one after

approximately 200 times of dust fulllment as a

guide. Failure to do so may cause dust inhalation.

1. Remove the dust case while pressing down the

lever of the dust case.

► Fig.38: 1. Lever

2. Open the cover of the dust case.

► Fig.39: 1. Cover

3. Dispose of the dust, and then clean the lter.

► Fig.40

NOTICE: When cleaning the lter, tap the case

of the lter gently by hand to remove dust. Do not

tap the lter directly; touch the lter with brush

or similar; or blow compressed air on the lter.

Doing so may damage the lter.

Blow-out bulb

Optional accessory

After drilling the hole, use the blow-out bulb to clean the

dust out of the hole.

► Fig.41

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating the tool.

► Fig.42

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust

cup set due to the heat produced by small metal

dust or similar.

NOTICE: Do not install or remove the dust cup

set with the drill bit installed in the tool. It may

damage the dust cup set and cause dust leak.

Connecting lanyard (tether strap) to

the hook

Safety warnings specic for use at height

Read all safety warnings and instructions. Failure to follow

the warnings and instructions may result in serious injury.

1. Always keep the tool tethered when working

"at height". Maximum lanyard length is 2 m.

The maximum permissible fall height for lan-

yard (tether strap) must not exceed 2 m.

2. Use only with lanyards appropriate for this tool

type and rated for at least 8.0 kg.

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

7.

Fasten the other end of the lanyard outside the

working area so that a falling tool is held securely.

8.

Attach the lanyard so that the tool will move away

from the operator if it falls. Dropped tools will swing on

the lanyard, which could cause injury or loss of balance.

9. Do not use near moving parts or running

machinery. Failure to do so may result in a crush

or entanglement hazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps switches or trigger-lock (if supplied)

from operating properly.

13. Avoid getting tangled in the lanyard.

14.

Keep lanyard away from the drilling area of the tool.

15. Use a locking carabiner (multi-action and

screw gate type). Do not use single action

spring clip carabiners.

16. In the event the tool is dropped, it must be

tagged and removed from service, and should

be inspected by a Makita Factory or Authorized

Service Center.

Sayfa yükleniyor ...

Makita HR001G Kullanım kılavuzu

Makita HR001G Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler