Yamaha mLAN Driver El kitabı

Marka: Yamaha

Modeli: mLAN Driver

Kategori: Klavyeler

Tip: El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

MY16

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

mLAN INTERFACE CARD

MY16-mLAN

English

DeutschFrançais

English

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but

are not limited to, the following:

• Before installing the MY16-mLAN in an audio device please check to make sure that the device is

compatible with the MY16-mLAN, and check possible restrictions regarding the maximum number of

Yamaha and third-party expansion cards that can be simultaneously installed. Refer to the operation manual

supplied with the audio device, and/or the Yamaha Pro Audio web site at: http://www.yamahaproaudio.com/

• Do not install the MY16-mLAN card in any Yamaha products not specified by Yamaha for use with the

MY16-mLAN to avoid possible electrical shock, fire, or equipment damage.

• Do not attempt to disassemble or modify the card. Do not apply excessive force to card connectors or other

card components. Mishandling of the card may lead to shock, fire hazard, or equipment failure.

• Be sure to disconnect the power cable of the main unit before installing this card (in order to eliminate

shock hazard).

• Turn off all peripheral devices of the host device before installation and unplug all cables connecting the

host device to all peripheral devices.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or

others, or damage to the device or other property. These precautions include, but are not limited to, the

following:

• Do not touch the metallic leads (pins) of the circuit board when handling the card. The pins are sharp and

may cause hand cuts.

• Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands on sharp edges.

• Avoid touching exposed connectors and metal parts to minimize the possibility of bad connections.

• Drain all static electricity from your clothing and body before handling the card. Static electricity can

damage the card. Touch an exposed metal part of the host device or other grounded object beforehand.

• Do not drop the card or subjecting it to shock, which can cause breakage and/or malfunction.

• Do not drop screws or other small parts inside the card. If power is applied while screws or similar metal

objects are loose inside the unit the card may malfunction or be damaged. If you cannot retrieve dropped

objects yourself, refer the problem to qualified Yamaha service personnel.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or

data that is lost or destroyed.

English

Introduction

Thank you for purchasing the Yamaha MY16-mLAN.

The MY16-mLAN is an interface card that features an mLAN interface. mLAN is a digital

network designed for music and is based on the IEEE1394 high performance serial bus

and data communication protocol. mLAN makes it easy to construct sophisticated net-

works for IEEE1394 (FireWire/i.LINK) audio and MIDI signals without having to re-con-

ﬁgure the cabling, as was necessary in older, conventional systems.

This interface card adds two mLAN connectors to MY16-mLAN compatible devices

such as the 02R96 and 01V96 digital mixing consoles, or the DM2000 and DM1000

digital production consoles.

In order to take full advantage of the MY16-mLAN’s functionality, please read this man-

ual carefully. After reading this manual, please keep it available for future reference.

Package Contents

• MY16-mLAN unit

• Tools for MY16-mLAN (CD-ROM)

• Owner’s Manual (this document)

• Tools for MY16-mLAN Installation Guide

If you’re using the 01V

If the MY16-mLAN is installed in the 01V, the MY16-mLAN will operate in maximum

audio input/output 8-in/8-out, wordclock 44.1 kHz / 48 kHz only, and transmission

speed 400 Mbps. Also, it will be shown as MY8-mLAN in the 01V’s display (page 7).

About the included CD-ROM

The MY16-mLAN is shipped with a CD-ROM that contains software that is useful

when used in conjunction with the MY16-mLAN. This software includes drivers that

are required to connect the MY16-mLAN to a computer. It also includes “mLAN

Graphic Patchbay,” which enables you to route audio and MIDI signals between

mLAN devices. For more information, refer to the separate “Tools for MY16-mLAN

Installation Guide” and the mLAN Graphic Patchbay PDF manuals.

English

• The illustrations and LCD screens shown in this Owner’s Manual are for instructional

purposes only and may appear somewhat different from those on your device.

• mLAN is a trademark of Yamaha Corporation.

• Company names and product names in this Owner’s Manual are the trademarks or

registered trademarks of their respective owners.

Features

■ Fast data transfer via mLAN

mLAN is a digital network designed for music. It uses the IEEE1394 high performance

serial bus and allows you to construct systems that are more sophisticated yet simpler

than ever before. The MY16-mLAN can transmit data at a transfer rate of up to

400Mbps (S400).

■ Set up mLAN connections intuitively using a graphical user inter-

face

From your computer you can specify the audio/MIDI signal ﬂow and make synchroni-

zation settings intuitively and easily; the “mLAN Auto Connector” software makes it

easy to connect mLAN devices to your computer, and “mLAN Graphic Patchbay” lets

you connect multiple mLAN devices simply by making settings on your computer

screen.

■ Up to 16 channels of audio I/O and one MIDI I/O port

When the device in which the MY16-mLAN is installed is connected to other mLAN

devices, you have up to 16-in and 16-out channels of audio, plus 1-in and 1-out MIDI

port.

If the MY16-mLAN is installed in the 01V, the maximum number of audio chan-

nels is 8-in and 8-out.

Yamaha is not held responsible for damage caused by improper use of or mod-

iﬁcations to the device or for data that is lost or destroyed.

NOTE

English

Table of Contents

Introduction............................................................................. 3

Package Contents .................................................................... 3

Features ................................................................................... 4

Fundamentals of mLAN............................................................ 5

Operational Flow for Sound Output ......................................... 6

Devices that are compatible with the MY16-mLAN .................. 7

Installing the MY16-mLAN ....................................................... 8

Names and Functions .............................................................. 9

Connections .......................................................................... 10

System Examples ................................................................... 11

Making mLAN Connections ................................................... 14

Troubleshooting .................................................................... 15

Specifications......................................................................... 20

Fundamentals of mLAN

mLAN is a digital network for music that was developed based on IEEE1394, an indus-

try-standard high-performance data communications protocol.

Digital music environments that do not feature mLAN require dozens of cables for vari-

ous devices and purposes, including MIDI cables and audio cables to route MIDI and

audio signals. If you wish to make changes to such systems, you must physically discon-

nect and re-connect these cables.

For example, adding another synthesizer to a system requires two MIDI cables and two

or more cables for audio (for stereo equipment). Making the appropriate connections

may require special knowledge of inputs, outputs, stereo settings, and perhaps connec-

tor impedance.

English

The larger the system, the more complicated and expensive these connections

become, increasing the likelihood of errors and difﬁculties. It takes time and effort to

investigate such errors and their underlying causes. You may have already experienced

the unpleasantness of tracking various cables through a spider’s web of connections.

mLAN simpliﬁes cable connections by using only one type of IEEE1394 cable, thus

enabling you to conﬁgure extremely sophisticated systems. There is no need to re-

patch cables to change routings of MIDI and audio signals between mLAN devices.

Operational Flow for Sound Output

1. Install the MY16-mLAN into your device.

..............See page 8.

2. Install Tools for MY16-mLAN.

..............See “Installing the Software” in the Installation Guide.

3. Connect the computer and mLAN devices using the IEEE1394 cables.

..............See page 10.

4. Turn on mLAN Manager (Windows only).

..............See “Conﬁrming the installation” in the Installation Guide.

5. To connect a computer to a single mLAN device directly, ﬁrst start mLAN

Auto Connector. To connect a computer to multiple mLAN devices, start

mLAN Graphic Patchbay.

..............See page 14.

6. Conﬁgure connections in mLAN Auto Connector or mLAN Graphic Patchbay.

..............Using Auto Connector: See “Connecting a Computer to an mLAN

device via mLAN” in the Installation Guide.

..............Using Graphic Patchbay: See “mLAN Connection Settings” in the

Graphic Patchbay Online Manual.

7. Make settings for audio and MIDI input/output as described in the owner’s

manual for your DAW (Digital Audio Workstation) or your connected

device(s).

For subsequent steps, refer to the owner’s manual for the software and connected

devices.

In this manual, setting up audio, MIDI, and wordclock routings is referred as

“mLAN connection.”

NOTE

English

Devices that are compatible with

the MY16-mLAN

If you’re using a device that has more than one mini-YGDAI slot

If you will be handling MIDI data in your mLAN system, install the MY16-mLAN into “slot 1”

of your device. If it is installed in other than “slot 1,” you won’t be able to transmit or receive

MIDI.

Compatible devices

The MY16-mLAN can be installed in the following devices. This table also shows the

maximum number of audio input and output channels and MIDI ports that can be

used with the MY16-mLAN.

If you’re using the 01V

If the MY16-mLAN is installed in the 01V, the MY16-mLAN will operate in max-

imum audio input/output 8-in/8-out, wordclock 44.1 kHz / 48 kHz only, and

transmission speed 400 Mbps. Also, it will be shown as MY8-mLAN in the

01V’s display.

If you’re using a 01V96/DM1000 system version earlier than 2.01,

or 02R96/DM2000 system version earlier than 2.11

In order to allow it to operate as the MY16-mLAN, you will need to update your

device. For details on updating, refer to the following URL.

Yamaha Pro Audio

http://www.yamahaproaudio.com/

Compatible

device

Maximum number of audio channels

Number of

MIDI ports

Fs: 44.1kHz/48kHz Fs: 88.2kHz/96kHz

01V

(Ver. 1.06 or later)

8In / 8Out Not supported

1In / 1Out

01V96

(Ver. 2.01 or later)

16In / 16Out 8In / 8Out

02R96

(Ver. 2.11 or later)

DM1000

(Ver. 2.01 or later)

DM2000

(Ver. 2.11 or later)

NOTE

English

Installing the MY16-mLAN

Here’s how to install the MY16-mLAN in your device. You should also refer to the

owner’s manual of the device into which you’re installing the MY16-mLAN.

Before you begin the installation, carefully read the “PRECAUTIONS” on

page 2.

Don’t change the setting of DIP switch SW1. The unit may no longer operate

correctly if you move SW1. If you inadvertently move it, restore the factory set-

tings as described below.

1. Set the MY16-mLAN’s DIP switch SW2 as appropriate for your device. If

you’re installing the MY16-mLAN in a device other than the 01V, set this

switch to “ON:OTHERS.” If you’re installing the MY16-mLAN in the 01V, set

this switch to “OFF:01V.”

You must set the DIP switch before installing the MY16-mLAN in your device. You

won’t be able to change the DIP switch setting once you’ve installed the MY16-

mLAN. If you need to change the setting, turn off the power of your device,

remove the MY16-mLAN, and then change the setting.

2. Install the MY16-mLAN in your device. For details, refer to the owner’s man-

ual of the device in which you’re installing it.

Before you install the card, you must power off any peripheral equipment con-

nected to the device in which you’re installing it, and disconnect all cables.

The screws also function as an electrical ground, so be sure to tighten them

securely.

The device in which you’re installing the MY16-mLAN must remain power off

while you install the MY16-mLAN.

3. Connect the device in which the MY16-mLAN is installed to your mLAN

devices or IEEE1394-compatible computer (page 10).

SW1

SW2

Factory settings:

1–3: OFF

4: ON

A switch is “OFF”

when the white

slider is moved

toward the number.

English

Names and Functions

A mLAN (IEEE1394) jacks

These 6-pin IEEE1394 standard jacks enable you to connect mLAN devices or

IEEE1394-compatible (FireWire/i.LINK) computers.

If the connecting device features a 6-pin IEEE1394 jack, use a standard 6-pin to 6-

pin IEEE1394 cable. If it features a 4-pin IEEE1394 jack, use a standard 6-pin to 4-pin

IEEE1394 cable. Do not connect the cables in a loop. (See page 17).

We recommend S400 compatible IEEE1394 cables (mLAN cables) that are

no longer than 4.5 meters.

B ACTIVE indicator

This indicator lights up when the MY16-mLAN is operating.

The indicator turns off when an error occurs during an operation.

When you click the [ID (Identify)] button in mLAN Auto Connector or mLAN

Graphic Patchbay (page 14) to identify the corresponding mLAN device in the net-

work, the indicator ﬂashes.

The indicator also lights up if an mLAN cable is not connected to the unit.

1 2

NOTE

English

Connections

This section explains how to connect the MY16-mLAN to other mLAN devices and to

your computer.

Connecting an mLAN (IEEE1394) device

Connect the mLAN (IEEE1394) connector on the mLAN device and IEEE1394-compati-

ble computer to the mLAN connector on the MY16-mLAN using IEEE1394 (FireWire/

i.LINK) cables. At this time, you do not have to turn off the power to the mLAN device

or the MY16-mLAN-equipped device.

mLAN (IEEE1394) device

IEEE1394-compatible computer

IEEE1394

cable

IEEE1394 cable

mLAN16E

MY16-mLAN

English

System Examples

This section introduces typical system examples that feature the MY16-mLAN. Refer to

these examples for information on connecting external devices, such as microphones,

musical instruments, and computers.

Using the MY16-mLAN connected to your computer

Use an IEEE1394 cable to connect the IEEE1394 connector on an IEEE1394-compatible com-

puter to the mLAN connector on an MY16-mLAN-equipped device. Use the mLAN Auto

Connector or mLAN Graphic Patchbay software application (See page 14) on the computer

to patch the audio and MIDI signals and to set up the wordclock. By making an mLAN con-

nection between your computer and the MY16-mLAN-equipped device, you’ll be able to

transfer multiple channels of audio in realtime between your computer and the device.

Like example below, we recommend that you use the USB cable in the opera-

tion of Studio Manager. If you use the mLAN/MIDI cable to transmit or receive

MIDI, operating Studio Manager may require more time.

*1: The 01V is not supplied with editor software for a computer.

*2: The 01V is limited to 44.1 kHz / 48 kHz, and 8-in/8-out.

NOTE

IEEE1394-compatible

computer

Digital mixer such

as the 01V96

MY16-mLAN

DAW

Studio

Manager

USB

connector

IEEE1394

cable

USB

cable

AUDIO

44.1kHz/48kHz:

16In / 16Out

88.2kHz/96kHz:

8In / 8Out

MIDI

1port

MIDI

1port

mLAN Auto

Connector/

mLAN Graphic

Patchbay

Editor

English

System conﬁgured around Yamaha 01V96 Digital Mixing Console

Use IEEE1394 cables to connect an MY16-mLAN-equipped 01V96, an i88X audio MIDI

interface, an mLAN16E-equipped MOTIF ES music production synthesizer, and an

IEEE1394-compatible computer. Use mLAN Graphic Patchbay (See page 14) on the

computer to patch the audio and MIDI signals and to set up the wordclock. Conﬁgur-

ing an mLAN system around the 01V96 enables you to do the following:

• Transfer audio and MIDI data between mLAN devices simply by connecting them via

IEEE1394 cables

• Set up and modify audio and MIDI signal patches between mLAN devices in various

situations using mLAN Graphic Patchbay, without physically re-patching cables

Like example below, we recommend that you use the USB cable in the opera-

tion of Studio Manager. If you use the mLAN/MIDI cable to transmit or receive

MIDI, operating Studio Manager may require more time.

NOTE

MOTIF ES

VOL VOL

01V96

MY16-

mLAN

mLAN16E

i88X

DAW

Studio Manager

mLAN Graphic

Patchbay

MicrophoneGuitar/Bass Synthesizer

IEEE1394

cable

IEEE1394 cable

IEEE1394

cable

USB

cable

Monitor system

IEEE1394-compatible

computer

ADAT recorder/Mixer

English

The number of available input and output channels may vary depending on

the speciﬁc mLAN devices connected. For the best performance, it is recom-

mended that you connect up to four mLAN devices (including a computer) in a

network. If the network contains an mLAN device that is only compatible with

a low transfer rate (200 Mbps (S200)), the number of devices and channels

available for connection will be reduced.

Wordclocks

In a system that features multiple digitally-connected devices, all digital devices

must be synchronized when digital audio signals are transferred from one device to

another.

Even if the devices use matching sampling frequencies, if their audio processing tim-

ing is not synchronized, they might not receive signals correctly, and audible noise,

glitches or clicks may occur. Synchronization is achieved using a wordclock

(a clock signal that synchronizes all digital audio signals in a system).

In a typical digital audio system, one device operates as the wordclock “master” and

transmits a wordclock signal. The other devices operate as wordclock “slaves,” syn-

chronizing to the wordclock master. To connect the MY16-mLAN to external devices

via mLAN, you must ﬁrst make clock settings for the device in which the MY16-

mLAN is installed. Then in mLAN Auto Connector or mLAN Graphic Patchbay, select

a device to be the master, and set the other devices as slaves. If the MY16-mLAN is

used as a wordclock slave, it can operate at a sampling frequency of 44.1 kHz,

48 kHz, 88.2 kHz or 96 kHz. If the MY16-mLAN is used as the wordclock master, it

will operate at the wordclock used by the MY16-mLAN-equipped device.

For information on setting the sampling frequency and wordclock, refer to the

Installation Guide, or to the mLAN Graphic Patchbay Online Manual, or the owner’s

manual for your device.

NOTE

English

Making mLAN Connections

In an mLAN system, you can easily conﬁgure and maintain the system, connect or dis-

connect the mLAN connectors on the computer and each mLAN device (virtual audio /

MIDI input and output connectors), and make various mLAN connection settings (such

as synchronization) by using the mLAN Graphic Patchbay and mLAN Auto Connector

software applications. There is no need to re-patch audio and MIDI cables to accom-

modate various music production environments.

mLAN Auto Connectors

This software application enables you to

connect a computer to a single mLAN

device.

It enables you to easily select wordclock and

audio input and output channels.

For information on installing and using the

software, refer to the separate Installation

Guide.

You can also use mLAN Graphic

Patchbay to connect a computer

to a single mLAN device.

mLAN Graphic Patchbay

This graphic software application enables

you to manage mLAN connection settings

for the connected computer and multiple

mLAN devices. You can immediately grasp

connections in their entirety by viewing dis-

played mLAN system conﬁguration graph-

ics. You can also intuitively modify

wordclock settings and audio and MIDI sig-

nal routing, much as if you were connecting

physical cables.

For information on installing and using the

software, refer to the separate Installation

Guide and the mLAN Graphic Patchbay

Online Manual.

Saving mLAN connection settings to the corresponding mLAN device

When you make mLAN connections on the computer, the connection settings will be automati-

cally saved in the corresponding mLAN devices. Therefore, if you used mLAN Graphic Patch-

bay to conﬁgure a network that excludes a computer, the next time you use the network, you

will be able to activate the network just by turning on the power to the network’s mLAN devices

(without starting the computer).

NOTE

English

Troubleshooting

If you encounter a problem...

If you hear no sound or a strange sound, ﬁrst check the items described below and take

appropriate action. If the problem persists, consult your Yamaha dealer.

■ No sound or very low volume level

• Are speakers or headphones connected correctly to the MY16-mLAN-equipped device?

• Are your amp and other external devices for the MY16-mLAN-equipped device turned on?

• Are all the level settings (of any tone generators, playback devices and the application itself)

appropriate?

• The connection cable from the external device to the MY16-mLAN-equipped device may be

broken.

• Is the wordclock setting correct for both the MY16-mLAN and the external device(s)?

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide, and “Wordclock Settings” in the mLAN Graphic Patchbay

Online Manual.

• (For Windows) Is mLAN (mLAN Driver) set to “ON”? From the task bar, right click on the

mLAN Manager (mLAN icon).

• Are the other settings of mLAN appropriate?

.......Refer to “Unable to communicate via mLAN (page 17).”

• If there are more than four devices (including a computer) on the network, the limit of the

IEEE1394 BUS bandwidth may be exceeded.

• The limit of the IEEE1394 BUS bandwidth may have been exceeded. Check the current band-

width using mLAN Graphic Patchbay, and disconnect some devices if necessary.

.......Refer to “Menu Bar” in the mLAN Graphic Patchbay Online Manual.

• If there is an mLAN device that supports only S200 on the mLAN network, the IEEE1394 BUS

bandwidth may be reduced and its limit exceeded. Reduce the number of mLAN devices con-

nected to the network, or disconnect some devices as necessary.

.......Refer to “Menu Bar” in the mLAN Graphic Patchbay Online Manual.

■ Distorted sound

• The connection cable from the external device may be broken.

• Is the wordclock setting correct for both the MY16-mLAN and the external device(s)?

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “Wordclock Settings” in the mLAN Graphic Patchbay

Online Manual.

• Make sure audio data was recorded at an appropriate level.

■ Noise is audible

• Is the latency setting of the mLAN Driver appropriate?

.......Refer to “mLAN Driver Setup” and “ASIO mLAN Control Panel” in the Instal-

lation Guide.

• (For Windows) Setting Hyper Threading to off in the BIOS settings may solve the problem.

• Is the wordclock setting correct for both the MY16-mLAN and the external device(s)?

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “Wordclock Settings” in the mLAN Graphic Patchbay

Online Manual.

• If the speed of your computer’s hard disk is slow, problems may occur during recording and

playback.

English

• If you connect/disconnect the LAN, USB or the cables to the mini jacks terminals on the Macin-

tosh you are using when using mLAN, some noise may be caused and/or data may be cut off.

Make sure that you do not insert or unplug any connections when using mLAN.

• Is the number of audio channels appropriate? The amount of audio channels that can be used

simultaneously differs depending on the computer capacity and speed.

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

• Is the sampling rate (wordclock) appropriate? A high sampling rate can be the cause of the

noise depending on the computer capacity and speed.

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

• Make sure that the appropriate number of devices is connected to the computer. Connection

of too many devices may cause noise, depending on the capacity of the computer.

• Are there any noise-producing devices (such as those containing power inverters, etc.) near the

cables? Move all cables away from any possible noise sources.

• Make sure the mLAN cable is not damaged. Cables that do not satisfy IEEE1394 standards may

cause noise.

• (For Windows) Do not run applications, such as anti-virus software, in the background. While

using the mLAN system, turn off all applications that run in background. If these applications

remain on, driver operation may become unstable and cause noise. If you do not plan to use

the mLAN system, you can turn these applications on. (You can turn the mLAN driver on and

off using mLAN Manager.)

■ Insufﬁcient tracks for recording or playback

• Is the number of channels for mLAN audio receiving/sending (set on the mLAN Auto Connec-

tor and mLAN Graphic Patchbay) appropriate?

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

■ Unable to transfer MIDI data or Program Changes

• Are the mLAN cables connected correctly?

• An mLAN cable may be broken.

• Is the power turned on for the transmitting and receiving devices?

• Make sure the transmission and reception channels match.

■ Incorrect pitch

• Is the unit operating on the same sampling frequency as the synchronized external device?

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “Wordclock Settings” in the mLAN Graphic Patchbay

Online Manual.

• Is the master device operating in a stable way?

■ Cannot change the wordclock

• While using the mLAN system, make wordclock settings using mLAN Auto Connector or mLAN

Graphic Patchbay.

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “Wordclock Settings” in the mLAN Graphic Patchbay

Online Manual.

English

■ Unable to communicate via mLAN

• Has the driver been installed? ................................................... Refer to the Installation Guide.

• Is the mLAN cable properly connected? Check the connection; disconnect the mLAN cable

once, then insert it again.

• (For Windows) Is mLAN set to “ON”? From the task bar, right click on the mLAN Manager

icon. .......Refer to “Conﬁrming the installation” in the Installation Guide.

• (For Windows) When adding a new IEEE1394 card, right click on the mLAN Manager icon in

the task bar and select “ON”.

.......Refer to “Conﬁrming the installation” in the Installation Guide.

• Is the ACTIVE lamp on the rear panel of the MY16-mLAN lit (in blue)? If it is not lit, check the

followings:

- In mLAN Driver Setup, is the Status indicator blue? If not, restart the MY16-mLAN-equipped

device and re-enable connection by using mLAN Auto Connector or mLAN Graphic Patch-

bay. .......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

• Has connection been enabled with mLAN Auto Connector and/or Graphic Patchbay? Re-

enable connection if necessary.

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

• Have you changed the device? Even if the model is the same, if the actual device is different, it

is necessary to re-enable connection by using Auto Connector and/or Graphic Patchbay.

.......Refer to “Connecting a Computer to an mLAN device via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

• Is there a loop connection? Check the cabling and make sure none of the devices are con-

nected in a loop.

• There may be a limit on the IEEE1394 interface of your computer as to the number of ports

that can be used simultaneously. Check how many ports can be used simultaneously.

.......Refer to “Maximum Number of Connected Node” in the mLAN Graphic

Patchbay Online Manual.

•Turn off all devices on the mLAN network (except the computer) and re-connect each device

one-by-one until the device causing the problem is found.

• (For Windows) (When removing the mLAN bus from the [Safely Remove Hardware] setting of

the task bar.) Restart the computer when using mLAN again.

•With Macintosh notebook computers such as the iBook and PowerBook, always ﬁrst connect

the MY16-mLAN-equipped device and mLAN cable then turn on the power of the MY16-

mLAN-equipped device, before starting up the computer.

• Make sure that you set up the wordclock correctly. Also, make sure that one node is assigned as

master and the other nodes are assigned as slaves.

.......Refer to “mLAN Connection Settings” in the mLAN Graphic Patchbay Online

Manual.

Computer

mLAN device

: IEEE 1394-equipped device

English

■ An application, such as a DAW, fails to recognize the mLAN driver (MIDI/audio).

• (For Windows) Make sure mLAN has not been turned off. On the task bar, right-click mLAN

Manager ( ), then select ON.

.......Refer to “Conﬁrming the installation” in the Installation Guide and “mLAN

Connection Settings” in the mLAN Graphic Patchbay Online Manual.

• Make sure the MY16-mLAN is connected to the mLAN cable and is powered on. Start mLAN

Auto Connector or mLAN Graphic Patchbay, then re-connect the device.

.......Refer to “Conﬁrming the installation” in the Installation Guide and “mLAN

Connection Settings” in the mLAN Graphic Patchbay Online Manual.

• (For Macintosh) To use an iBook or PowerBook in the system, connect the MY16-mLAN-

equipped device to the Macintosh using an mLAN cable, turn on the power to the MY16-

mLAN-equipped device, then start the Macintosh.

• Make sure the mLAN settings are correct.

.......Refer to “Unable to communicate via mLAN” on page 17.

■ The computer processing speed is too slow.

■ The computer’s CPU meter indicates a heavy processing load.

■ Playback response is delayed.

• Make sure your computer satisﬁes the system requirements.

.......Refer to “System Requirements” in the Installation Guide.

• (For Windows) If you do not use the mLAN system, on the task bar right-click mLAN Manager

( ), then select OFF (mLAN quits).

.......Refer to “Conﬁrming the installation” in the Installation Guide.

•Try reducing the number of audio channels in mLAN Auto Connector or Graphic Patchbay.

.......Refer to “Connecting the Computer and mLAN devices via mLAN” in the

Installation Guide and “mLAN Connection Settings” in the mLAN Graphic

Patchbay Online Manual.

•Try increasing the latency value.

..........Refer to “Changing the Settings after Installation” in the Installation Guide.

• (For Windows) Refer to “Hints when using audio data (Windows).”

.......Refer to the Installation Guide.

• (For Windows) The condition may improve if you set “Hyper Threading” to “Disable.”

• Using mLAN Graphic Patchbay, try reducing the number of devices connected to the com-

puter. .......Refer to “mLAN Connection Settings” in the mLAN Graphic Patchbay Online

Manual.

• If multiple S200-compatible devices are connected to the network, connecting mLAN devices

in mLAN Graphic Patchbay may require more time.

■ Inconsistency in wordclock, or unable to exit from Auto Connector

• (For Windows) Mobile computers with Intel CPU

SpeedStep™ technology is applied for some CPU’s (CPU for notebook PC). Please disable the

SpeedStep™ technology when mLAN is employed. SpeedStep™ technology changes CPU

clock dynamically depending on the loading on the CPU to save the power consumption.

- How to disable the SpeedStep™ technology;

In almost all of the PC’s, BIOS has a function to select enabling or disabling the SpeedStep™

technology. Please refer to the PC’s operating manual, or make inquiry to the PC manufac-

turer.

English

■ Unable to close the application or operating system

■ Unable to change the mLAN settings

■ Unable to uninstall mLAN Applications for Yamaha or mLAN Tools 2.0

• (For Windows) Is the mLAN (WDM) driver selected as the default audio device for the system?

- Select [Start | Control Panel | Sounds and Audio Devices | Voice].

Make sure that something other than “mLAN Audio 01” is selected for the [Voice playback]

and [Voice recording] settings.

- Select [Start | Control Panel | Sounds and Audio Devices | Audio].

Make sure that something other than “mLAN Audio 01” is selected for the [Sound play-

back] and [Sound recording] settings.

- In “MIDI music playback,” select any option other than the range of options from “mLAN

MIDI Out” through “mLAN MIDI Out (8).”

• (For Windows) Select [Start | Control Panel | Sounds and Audio Devices | Sounds]. And select

“No sounds” in the [Sound scheme], then execute again.

• (For Windows) If you cannot quit mLAN (by selecting “OFF” after right clicking the mLAN icon

in the task bar), end the processes listed below manually. ([Ctrl] + [Alt] + [Delete] → [Processes]

→ select process → [End process]) When ﬁnished, start mLAN Manager to change the mLAN

settings again.

- mLANVDevice.exe

- mLANTFamily.exe

- mLANSoftPH.exe

- mLANManager.exe

To change mLAN settings, select [Start | (All) Programs | Start Up], then start mLAN Manager.

- (When a message such as “ﬁle cannot be found” appears when uninstalling:)

Try executing the installation once more, then uninstall again.

■ (Windows) mLAN Manager (the mLAN icon in the Task bar) has disappeared.

• Select [Start | (All) Programs | Start Up (or mLAN Tools)], then select mLAN Manager.

■ Launching mLAN Graphic Patchbay or updating to the latest information takes a

while.

• When you try to update the network information after connecting or disconnecting an mLAN

device that does not support S400, the system adjusts the mLAN transfer speed, and requires

more time to process your request. However, this will not affect any subsequent operations.

• If ﬁve or more mLAN devices (including a computer) have been connected to a network, the

total number of transmission channels of all devices will be limited. You can connect up to 86

channels in Windows and up to 98 channels in a Macintosh system.

English

Speciﬁcations

Speciﬁcations and appearance subject to change without notice.

Supported Host

products

01V96, DM1000, 02R96 (up to 3 cards), DM2000 (up to 3

cards), 01V

01V96 and DM1000: Supported in V2.01 or later.

02R96 and DM2000: Supported in V2.11 or later.

01V: Supported in V1.06 or later; operates as MY8-mLAN

Data Rate S400,S200

Audio

I/O: 16In/16Out @ 48kHz / 44.1kHz (8In/8Out @ 88.2kHz /

96kHz)

Fs: 44.1kHz-10% to 48kHz+6% (88.2kHz-10% to 96kHz+6%)

Resolution: 24bit

MIDI

1In/1Out, Baudrate: 31.25kbps

Necessary for USB connections for using Multi Port MIDI

(SLOT1 is available for Digital console within multi SLOTs)

Wordclock Transi-

tion Speed setting

Slow/Fast

Speciﬁed by included mLAN Graphic Patchbay or Auto Con-

nector.

Indication LED ACTIVE (Blue)

Host device detec-

tion switch

01V/Others

Others number of node: Up to 5 nodes

Connectors To IEEE1394: 6 Pin x 2

Power Require-

ment

740mA (Max.) / +5V

Dimension

(WxDxH)

120 mm x 176.1 mm x 40 mm

(4-3/4" x 6-15/16" x 1-9/16")

Sayfa yükleniyor...

Yamaha mLAN Driver El kitabı

Marka: Yamaha

Modeli: mLAN Driver

Kategori: Klavyeler

Tip: El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

MY16

PDF''yi indir

rapor

diğer dillerde

español: Yamaha mLAN Driver El manual del propietario
français: Yamaha mLAN Driver Le manuel du propriétaire
italiano: Yamaha mLAN Driver Manuale del proprietario
svenska: Yamaha mLAN Driver Bruksanvisning
čeština: Yamaha mLAN Driver Návod k obsluze
polski: Yamaha mLAN Driver Instrukcja obsługi
Deutsch: Yamaha mLAN Driver Bedienungsanleitung
português: Yamaha mLAN Driver Manual do proprietário
English: Yamaha mLAN Driver Owner's manual
dansk: Yamaha mLAN Driver Brugervejledning
suomi: Yamaha mLAN Driver Omistajan opas
Nederlands: Yamaha mLAN Driver de handleiding
română: Yamaha mLAN Driver Manualul proprietarului

Yamaha mLAN Driver El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha mLAN Driver El kitabı

diğer dillerde

İlgili makaleler