Yamaha CD Recordable/Rewritable Drive CRW-F1 Kullanım kılavuzu

Marka: Yamaha

Model: CD Recordable/Rewritable Drive CRW-F1

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA.

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW-F1

CRW-F1-NB

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.

6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 779 – 789 nm

Pulse Durations and Max. Output

at the Objective Lens of the Laser Pickup Unit

DC Erase Mode: 20 mW Max. (Continuous),

Write Mode: Max.62 mW

(Max. Cycle 111 ns, Min. Cycle 30 ns at Max. Speed)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 779 – 789 nm

Impulsdauer und max. Ausgang an der

Objektivlinse der Laser-Abtasteinheit

Löschmodus (Gleichstrom): max. 20 mW (kontinuierlich),

Schreibmodus: max. 62 mW

(max. Zyklus 111 ns, min. Zyklus 30 ns bei maximaler Geschwindigkeit)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 779 – 789 nm

Durée des impulsions et sortie maximum depuis

la lentille de focalisation du bloc capteur optique

Mode de suppression DC: max. 20 mW (en continu),

Mode de gravure: max. 62 mW

(Cycle max. 111 ns, cycle min. 30 ns à vitesse maximale)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 779 – 789 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora de láser

Modo de borrado DC: 20 mW máx. (continua),

Modo de escritura: máx. 62 mW

(ciclo máx. 111 ns, ciclo mín. 30 ns a velocidad máxima)

OWNER’S MANUAL

English

SAFETY PRECAUTIONS

PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY TO

PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.

These precautions explain how to use the device properly and safely, thereby preventing

injury to yourself and others. This section has been sub-divided into a WARNING section

and a CAUTION section, according to the likelihood and nature of any potential injuries or

damage inflicted. They relate to your personal safety, and also help you prevent the risk of

damage to the device. Please read these sections carefully prior to proceeding.

WARNING

Always follow these basic precautions to avoid short-circuit, damage, fire, or other

hazards, and to avoid serious injury or fatal accident from electrical shock.

●

Do not attempt to open or disassemble the device to avoid the risk of electrical shock,

fire, or malfunction.

●

Do not look directly at the laser source to avoid the risk of eye damage or blindness.

●

Do not insert fingers or foreign objects into the device to avoid the risk of electrical

shock, fire, malfunction, or personal injury.

●

Do not expose the device to high humidity or place liquid containers such as a flower

vase on the device to avoid the risk of electrical shock, fire, or malfunction.

●

Do not expose the device to temperature outside the range of 5 to 40 °C (41 to 104 °F) to

avoid the risk of fire, deformation of the device panel, or malfunction.

●

Do not expose the device to dusty place to avoid the risk of fire or malfunction.

●

Always follow the owner’s manual to set up or connect the devices properly to avoid the

risk of electrical shock, fire, malfunction, or personal injury.

●

If unusual smells, sounds or smoke come from the device, or if foreign objects such as

liquid intrude into the device, turn off and unplug the computer immediately to avoid the

risk of electrical shock, fire, or malfunction. Contact the store of purchase or your nearest

Yamaha dealer (listed at the back of this manual).

●

Be sure that the computer is electrically grounded to avoid the risk of electrical shock.

●

Prior to cleaning the drive, always unplug the computer or do not handle the plug with

wet hands to avoid the risk of electrical shock.

iii

CAUTION

Always follow these basic precautions to avoid physical injury to yourself or others, and

damage to the device or other property.

●

Always unplug the computer if it will not be used for a prolonged period or if there is

possibility of lightning, to avoid the risk of electrical shock, fire, or short-circuit.

●

Do not use the device near other electrical appliances such as televisions, radios, or

speakers to avoid the risk of interferences between each other.

●

Do not place the computer unstably to avoid the risk of malfunction or personal injury by

its falling down.

●

Do not place the device with a possibility of excessive vibration to avoid the risk of

damage to written data or malfunction.

●

Place the device horizontally to avoid the risk of damage to written data.

●

Prior to transporting the device, remove the disc from the disc tray to avoid the risk of

damage to written data.

●

Use soft, dry cloths to wipe the device. Do not use benzene, paint thinner, detergents, or

chemically treated wiped cloths, and do not place vinyl, plastic, or rubber objects on the

device to avoid the risk of malfunction or damage to surface of the device.

●

Do not rest your weight on or place heavy objects on the device, and do not apply

excessive force to the buttons, switches, or connectors to avoid the risk of damage to the

device or personal injury.

●

Do not listen to audio with headphones at high volume for prolonged period to avoid

auditory disorder.

●

Prior to turning on the computer, always minimize the volume to avoid auditory disorder

by a sudden burst of sound at high volume.

●

Do not place the device near magnets or anything magnetized such as a display to avoid

the risk of interferences between each other.

●

Have the device serviced regularly to avoid internal dust buildup that can cause

malfunction, damage or fire. For service information and service charges, contact the

store of purchase or your nearest Yamaha dealer (listed at the back of this manual).

●

This drive is for use only with movable equipment, weighing less than 18 kg.

WARRANTY

YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR

AS A RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE

MANUAL FOR THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY DATA CAUSED AS

A RESULT OF USING THIS PRODUCT.

Precautions for Transportation

Transporting the device unfixed may damage its internal mechanism or circuits.

• Remove the disc from the disc tray of the device.

• Put the device in the original box.

For the Yamaha retail kit, refer to the original box to check that the complete accessories are

included prior to installation. Accessories vary depending on the model.

To reduce power consumption of the CRW-F1 drive, set your computer to power saving mode.

(P. 38)

• This document may not, in whole or in part, be copied, photocopied, reproduced, translated,

transmitted, or reduced to any electronic medium of machine readable form without prior

consent in writing from Yamaha.

• Windows is a registered trademark of Microsoft Corporation.

• DiscT@2™ and SafeBurn™ are trademarks of Yamaha Corporation.

• All other trademarks are the property of their respective companies.

™ and ® marks are not specified in this manual.

Table of Contents

Features of the CRW-F1 Drive..................................................... 1

Names and Functions of Parts.....................................................2

Front Panel...............................................................................................2

Rear Panel................................................................................................3

Precautions on Use.................................................................. 4

Handling Discs ........................................................................................4

Disclaimer of Indemnity..........................................................................4

Compatible Discs.....................................................................................5

System Requirements ..............................................................................8

Preparing the CRW-F1 Drive....................................................... 9

Serial Number..........................................................................................9

1 Decide the Installation Method..........................................................10

2 Set the Jumper Switch .......................................................................15

3 Install the CRW-F1 Drive..................................................................17

4 Check Recognition of the CRW-F1 Drive ........................................23

5 Install CD Writing Software..............................................................26

Loading/Ejecting a Disc ...........................................................27

Troubleshooting.....................................................................29

Firmware.............................................................................36

CRW-F1 Drive Specifications.....................................................37

Technical Notes.....................................................................40

Buffer Underrun Protection Function....................................................40

Writing Methods....................................................................................40

For details about installing and using the CD writing software, refer to the instruction for

it.

• The information contained in this manual is subject to change without prior notice.

• Reproduction of this manual, either in part or in full, is expressly forbidden.

Features of the CRW-F1 Drive

Advanced Audio Master Quality Recording (High quality audio writing mode)

Audio Master Quality Recording enables you to create high quality audio CDs that

can be played back beautifully on any compatible device including car stereos. In

addition, the data quality of your CDs can be preserved for a long time. (P. 41)

This mode is available for CD-R discs with a capacity of 650MB, 700MB, and

870MB.

DiscT@2

The DiscT@2 function enables you to burn texts/pictures on the data surface of a

CD-R disc. Writing software that supports the function is required to operate it. For

details about this feature, refer to the instruction for the writing software.

• The function cannot be used with a CD-RW disc.

• Appearance of burned images such as pictures varies depending on the material of a disc.

High speed writing/reading

The CRW-F1 drive supports up to 44X-speed writing for CD-R discs, up to 24X-

speed writing/rewriting for CD-RW discs, and up to 44X-speed data reading or

digital audio data extraction. The Full CAV method enables 44X-speed writing and

high fidelity stable writing at once for CD-R discs.

Tip

The Partial CAV method (P. 42) and the Full CAV method permit 24X-speed writing/

rewriting for CD-RW discs.

SafeBurn™ (Enhanced stability writing technology)

The generous 8MB buffer memory provides sufficient data storage to enable stable

disc writing at high speeds. Even if data transfer from the computer is interrupted,

the Buffer Underrun Protection function is activated to save CD-R discs from a

writing error. (P. 40)

“Optimum Write Speed Control” adjusts the writing speed to the optimum rate for

CD-R discs automatically. The maximum writing speed can be set with CD writing

software.

• “Optimum Write Speed Control” can be activated when the maximum writing speed

is set at 16X or more.

• The minimum writing speed to be automatically selected is 8X. Manually set the

optimum writing speed if a writing speed supported by a disc is less than 8X.

CD-MRW (CD Mount Rainier ReWriting)

CD-MRW is a new standard of packet writing. Compared to the ordinary packet

writing, CD-MRW provides many useful functions such as background formatting.

(P. 42)

Note

Names and Functions of Parts

➀

Disc tray

Holds the disc. It is opened or closed by

pressing the eject button. (P. 27)

➁

Manual eject hole

Forcibly opens the disc tray when the tray

cannot be opened by pressing the eject

button. (P. 28)

➂

Eject button

Press to open or close the disc tray.

(P. 27)

➃

Headphone jack

Connects headphones or external speakers

to the drive; has stereo mini-jack

specifications.

➄

Headphone volume dial

Controls the volume of the headphones.

The volume increases as the dial is turned

to the right.

➅

LED

Indicates the operational status of the

CRW-F1 drive by its colors and blinking

patterns.

Lights or blinks blue

• Lights: Standby (with disc)

• Blinks: Opening/Closing disc tray,

reading disc information (TOC), or

playback audio

• Blinks rapidly: Reading data

Blinks purple

• Blinks: Accessing for writing or test

writing

• Blinks rapidly: Writing

Blinks amber

Firmware update is incomplete. Retry to

update the firmware.

Off

Standby (no disc), the disc tray is open, or

power saving (operated via computer

setting)

Front Panel

➅

➁

➃➄

➀➂

Names and Functions of Parts

➀

DIGITAL AUDIO OUT

Connects to the sound card in the computer

using a digital audio cable if the sound card

has an S/PDIF (digital audio) input jack.

(P. 21)

➁

ANALOG AUDIO OUT

Connects to the sound card in the computer

using an audio cable. (P. 20)

➂

Jumper switch

Insert a plastic shunt into the switch to set

the connection of the IDE to master or

slave. The switch is set at slave by default.

(P. 15)

➃

IDE INTERFACE CONNECTOR

Connects a 40-pin IDE cable. (P. 18)

➄

DC INPUT

Connects the 4-pin internal power cable of

the computer. (P. 22)

Rear Panel

➁➀➂ ➃ ➄

Precautions on Use

Take the following precautions to avoid trouble, such as writing errors, loss of

recorded data, and malfunction of the drive, when handling discs.

• Do not place discs in a hot or damp place or where they will be exposed to direct

sunlight.

• Do not touch the disc surface. Hold the disc by the edge when handling it.

• Remove dust and dirt from the disc surface. Use an air spray to remove dust. The

disc surface may be scratched if strongly wiped with a dry cloth.

• Do not stick labels to the disc surface or write anything on it except where

designated.

• Do not clean discs with chemicals or detergents.

• Do not bend or drop discs.

It is prohibited by law to duplicate copyright material for non-personal use without

the prior consent of the copyright holder. When copying material with your CD-R/

RW drive, take due care not to infringe the copyright.

• Yamaha assumes no liability for the loss of any profits incurred as a result of the

loss or corruption of data written on a CD-R or CD-RW, for any loss or damage

caused by or arising out of extraordinary circumstances (including circumstances

that Yamaha has foreseen or could foresee), nor for any damages incurred or

claimed by a third party.

• After handling important data, make a comparison between the original and the

copied data (to confirm that the data has been copied properly).

• In no event shall Yamaha be liable for any damage to discs due to a buffer

underrun error (P. 40) or for any other reason, or the inability to use distributed

discs with your drive.

• Yamaha assumes no liability for the inability to write/playback discs because of

their format.

Handling Discs

Disclaimer of Indemnity

Precautions on Use

For the latest information about compatible discs, refer to the following website.

YAMAHA CD-R/RW Drive website

URL: http://www.yamaha.co.jp/english/product/computer/

Disc shape

Circular disc 12 cm, 8 cm

Card-type disc Discs confirmed by Yamaha

Do not use any irregular shaped discs such as heart-shaped or star-shaped discs to avoid

the risk of malfunction.

Recordable disc type

The CRW-F1 drive is compatible with the following discs.

Compatible Discs

Note

CD-R discs

• Orange Book Part2 Vol.1 Version3.1-compliant discs

• Orange Book Part2 Vol.2 Version1.1-compliant discs

Writing speed

The writing speed settings are available in writing software.

1X, 4X, 8X, 16X, 44X

• 44X-speed writing is enabled with the Full CAV method.

• Some writing speed settings may not be available depending on the specification of

a disc.

• When the writing speed is set at 16X or 44X, “Optimum Write Speed Control”

automatically adjusts the writing speed to the optimum rate for each disc within the

selected writing speed.

Device compatibility

CD-R discs can be read/played back on a CD-ROM drive or a CD player.

Note

CD-RW discs

• Orange Book Part3 Vol.1 Version1.0-compliant discs

• Orange Book Part3 Vol.1 Version2.0-compliant discs

Writing/Rewriting speed

The writing speed settings are available in writing software.

2X, 4X

• Some discs support only 2X speed.

• Some writing/rewriting speed settings may not be available depending on the

specification of a disc.

Device compatibility

CD-RW discs can be read/played back on a device that supports CD-RW discs

(e.g. CD-ROM drive).

High Speed CD-RW discs

Orange Book Part3 Vol.2-compliant discs

Writing/Rewriting speed

The writing speed settings are available in writing software.

4X, 10X, 12X

• Some writing/rewriting speed settings may not be available depending on the

specification of a disc.

• When using the packet writing method (P. 41) for writing/rewriting onto a High

Speed CD-RW disc, you can select the 10X Full CAV method. For more details,

refer to the instruction for the CD writing software. (CD writing software that has

the feature to select the Full CAV method is required.)

• The Full CAV method is recommended when editing a written file with application

software.

Device compatibility

High Speed CD-RW discs can be read/played back on a CD-RW device that bears

the High Speed CD-RW logo or a device that supports CD-RW discs (e.g. CD-

ROM drive).

In order to write, delete, read or play back a High Speed CD-RW disc, use a CD-R/RW

drive that bears the High Speed CD-RW logo. When using a CD-ROM drive to read/

play back a High Speed CD-RW disc, a drive supporting CD-RW discs is required.

A CD-R/RW drive without the logo may not recognize a High Speed CD-RW disc,

resulting in computer malfunction.

Refer to the Yamaha website to check the disc compatibility prior to using a

YAMAHA CD-R/RW drive without the logo for a High Speed CD-RW disc.

URL: http://www.yamaha.co.jp/english/product/computer/

Note

Continued on next page

Precautions on Use

Ultra Speed CD-RW discs

Orange Book Part3 Vol.3-compliant discs

Writing/Rewriting speed

The writing speed settings are available in writing software.

10X, 16X, 24X

• 24X-speed writing/rewriting is enabled with the Partial CAV method.

• Some writing/rewriting speed settings may not be available depending on the

specification of a disc.

• When using the packet writing method (P. 41) for writing/rewriting onto an Ultra

Speed CD-RW disc, you can select the 24X Full CAV method. For more details,

refer to the instruction for the CD writing software. (CD writing software that has

the feature to select the Full CAV method is required.)

• The Full CAV method is recommended when editing a written file with application

software.

Device compatibility

Ultra Speed CD-RW discs can be read/played back on a device that supports CD-

RW discs (e.g. CD-ROM drive) or a device that bears the High/Ultra Speed CD-

RW logo.

Note

The CRW-F1 drive is designed to operate in the following computer environment. If

your computer does not meet these requirements, the CRW-F1 drive may not write

at the maximum speed.

Computer (PC/AT compatible)

• CPU: Pentium II-class or higher, 300 MHz or faster

• RAM: 32MB (64MB or more is recommended)

64MB or more is required (128MB is recommended) for Windows 2000

Professional, while 128MB or more is required (256MB is recommended) for

Windows XP.

• An empty 5 ¼-inch drive bay (for installing the CRW-F1 drive as an additional

drive into the computer)

• Hard drive space

Writing data on a CD-R/RW disc requires 50MB to 100MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating an image file, there must be enough free space on the hard drive to store

the image file in addition to the working area (a total of up to 1.1GB).

However, hard drive space for image files is not required when directly writing

onto a CD-R/RW disc from a hard drive or CD-ROM using the CRW-F1 drive

(on-the-fly writing).

Image file

An image file is data files that are collected to be written on a CD-R/RW disc. The file

is useful for writing the same data onto multiple discs. For details, refer to the

instruction for the CD writing software.

Operating system

Windows 95 (OSR2 or later), Windows 98, Windows 98 Second Edition,

Windows Me, Windows 2000 Professional,

Windows XP (Home Edition/Professional Edition)

CD writing software

The CRW-F1 drive requires CD writing software to write onto a CD-R/RW disc.

Use the CD writing software that supports the CRW-F1 drive.

For details about installing and using the CD writing software, refer to the

instruction for it.

System Requirements

Preparing the CRW-F1 Drive

Preparing tools

• Phillips screwdriver: Use the proper screwdriver for

the screws to install the CRW-F1 drive into the

computer.

• Narrow pliers: Insert and remove the included plastic

shunt for the jumper switch.

The serial number, printed on the label on the top of your CRW-F1 drive, is required

when you have a question about the drive or need user support services.

Please write the serial number down in the space below prior to installing the CRW-

F1 drive into your computer. It will be difficult to check the serial number after

installation.

Serial Number

Serial number

(10 characters: 3 letters +

7 numbers)

The following describes how to install the CRW-F1 drive on the computer by taking

a tower-type computer for example.

The methods of removing the computer cover or panels and installing an internal device

vary depending on the computer model. Refer to the instruction for the computer.

Check the connection of any IDE device installed to decide the installation method

of the CRW-F1 drive.

• The CRW-F1 drive supports Ultra ATA/33. (The CRW-F1 drive is operated with

Ultra ATA/33 even if the motherboard or the IDE cable support Ultra ATA/66 or

Ultra ATA/100.)

• The 40-pin IDE cable (with 40 wires) included in a Yamaha retail kit supports Ultra

ATA/33. IDE devices connected to the 40-pin IDE cable are operated with Ultra

ATA/33 even if the devices support Ultra ATA/66 or Ultra ATA/100.

• Install the CRW-F1 drive horizontally.

Turn off and unplug the computer.

When handling internal computer devices, always turn off the computer to

avoid the risk of an electrical shock or damage to the drive or computer

devices. Be sure to unplug the computer prior to handling any internal

computer device.

Remove all peripheral devices and cables connected to the

computer prior to removing the computer cover.

Clothes and body can become charged with static electricity.

Discharge any static electricity by touching a metallic part of the case or

power unit.

For more information, refer to the instruction for the computer.

Note

1 Decide the Installation Method

Note

Preparing the CRW-F1 Drive

Installing the CRW-F1 drive as an additional drive

Check the IDE channel (primary/secondary and master/slave) connecting the CRW-

F1 drive. (P. 12 – 14)

An empty 5 ¼-inch drive bay is required to install the CRW-F1 drive.

Replacing an existing IDE device with the CRW-F1 drive

Connect the CRW-F1 drive to the cable that was previously connected to the IDE

device.

When replacing a SCSI device such as a SCSI type CD-ROM drive, do not connect the

CRW-F1 drive to the cable that was previously connected to the SCSI device. Use a 40-

pin IDE cable to connect the CRW-F1 drive to the computer.

Note

CRW-F1 drive

CD-ROM drive, etc.

Sayfa yükleniyor ...

Yamaha CD Recordable/Rewritable Drive CRW-F1 Kullanım kılavuzu

Marka: Yamaha

Model: CD Recordable/Rewritable Drive CRW-F1

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

PDF İndir

rapor

Diğer dillerde

français: Yamaha CD Recordable/Rewritable Drive CRW-F1 Manuel utilisateur
italiano: Yamaha CD Recordable/Rewritable Drive CRW-F1 Manuale utente
svenska: Yamaha CD Recordable/Rewritable Drive CRW-F1 Användarmanual
Deutsch: Yamaha CD Recordable/Rewritable Drive CRW-F1 Benutzerhandbuch
English: Yamaha CD Recordable/Rewritable Drive CRW-F1 User manual
dansk: Yamaha CD Recordable/Rewritable Drive CRW-F1 Brugermanual
Nederlands: Yamaha CD Recordable/Rewritable Drive CRW-F1 Handleiding
română: Yamaha CD Recordable/Rewritable Drive CRW-F1 Manual de utilizare

Yamaha CD Recordable/Rewritable Drive CRW-F1 Kullanım kılavuzu

Bu kılavuz için de uygundur

Yamaha CD Recordable/Rewritable Drive CRW-F1 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler