LG 32LH570U El kitabı

Tip
El kitabı

Bu kılavuz için de uygundur

Please read this manual carefully before operating your set and
retain it for future reference.
*MFL69311721*
www.lg.com
P/NO : MFL69311721(1603-REV00)
Printed in Korea
Safety and Reference
OWNER’S MANUAL
LED TV*
* LG LED TV applies LCD screen with LED
backlights.
2
ENGLISH
Safety instructions
Please read these safety precautions
carefully before using the product.
WARNING
Do not place the TV and/or remote control in
the following environments:
t A location exposed to direct sunlight
t An area with high humidity such as a
bathroom
t Near any heat source such as stoves and
other devices that produce heat
t Near kitchen counters or humidiers where
they can easily be exposed to steam or oil
t An area exposed to rain or wind
t Near containers of water such as vases
Otherwise, this may result in re, electric
shock, malfunction or product deformation.
Do not place the product where it might be
exposed to dust. This may cause a re hazard.
Mains Plug is the TV connecting/disconnecting
device to AC mains electric supply. This plug
must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or
wipe dust o. You may be electrocuted due to
excess moisture.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin.
(Except for devices which are not grounded
on earth.) Otherwise possibility you may be
electrocuted or injured.
Insert power cable plug completely into wall
socket otherwise if not secured completely into
socket, re ignition may break out.
Ensure the power cord does not come into
contact with hot objects such as a heater. This
may cause a re or an electric shock hazard.
Do not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in re or electric
shock.
3
ENGLISH
Bend antenna cable between inside and
outside building to prevent rain from owing
in. This may cause water damaged inside the
Product and could give an electric shock.
When mounting TV onto wall make sure to
neatly install and isolate cabling from rear of
TV as to not create possibility of electric shock /
re hazard.
Do not plug too many electrical devices into a
single multiple electrical outlet. Otherwise, this
may result in re due to over-heating.
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this
may result in injury or damage to the product.
Keep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause
suocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the
TV.
Otherwise, the TV may fall over, which may
cause serious injury.
Dispose of used batteries carefully to ensure
that a small child does not consume them.
Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not touch
the power cable right after plugging into the
wall input terminal. You may be electrocuted.
(Depending on model)
Do not put or store inammable substances
near the product. There is a danger of
combustion/explosion or re due to careless
handling of the inammable substances.
4
ENGLISH
Do not drop metallic objects such as coins,
hair pins, chopsticks or wire into the product,
or inammable objects such as paper and
matches. Children must pay particular
attention. Electrical shock, re or injury can
occur. If a foreign object is dropped into the
product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub
with an inammable substance (thinner or
benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects
to fall into the unit, and do not drop anything
onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a
thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there
is leakage of gas, open the windows and
ventilate. It may cause a re or a burn by a
spark.
Do not disassemble, repair or modify the
product at your own discretion. Fire or electric
shock accident can occur.
Contact the service centre for check, calibration
or repair.
If any of the following occur, unplug the
product immediately and contact your local
service centre.
t The product has been impacted by shock
t The product has been damaged
t Foreign objects have entered the product
t The product produced smoke or a strange
smell
This may result in re or electric shock.
Unplug the TV from AC mains wall socket if you
do not intend to use the TV for a long period of
time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric
leakage/shock/re.
5
ENGLISH
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could
be exposed to oil or oil mist. This may damage
the product and cause it to fall.
If water enters or comes into contact with TV,
AC adapter or power cord please disconnect
the power cord and contact service centre
immediately. Otherwise, this may result in
electric shock or re.
Only use an authorized AC adapter and power
cord approved by LG Electronics. Otherwise, this
may result in re, electric shock, malfunction or
product deformation.
Never Disassemble the AC adapter or power
cord. This may result in re or electric shock.
Be careful in handling the adapter to prevent
any external shocks to it. An external shock may
cause damage to the adapter.
Make sure the power cord is connected securely
to the power plug on the TV. (Depending on
model)
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an
outside antenna and power lines to keep the
former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as
unstable shelves or inclined surfaces. Also avoid
places where there is vibration or where the
product cannot be fully supported. Otherwise,
the product may fall or ip over, which may
cause injury or damage to the product.
6
ENGLISH
If you install the TV on a stand, you need to
take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.
If you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), x it
carefully so as not to drop.
Only use the attachments / accessories specied
by the manufacturer.
When installing the antenna, consult with a
qualied service technician. If not installed by
a qualied technician, this may create a re
hazard or an electric shock hazard.
We recommend that you maintain a distance
of at least 2 to 7 times the diagonal screen size
when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This could
cause damage to the remote control.
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and
leak.
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight, open replace and electric heaters.
Do not place non-rechargeable batteries in
charging device.
Make sure there are no objects between the
remote control and its sensor.
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
uorescent lighting. If this occurs turn o
lighting or darken viewing area.
When connecting external devices such as
video game consoles, make sure the connecting
cables are long enough. Otherwise, the product
may fall over, which may cause injury or
damage the product.
7
ENGLISH
Do not turn the product On/O by plugging-
in or unplugging the power plug to the wall
outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an
electric shock.
Please follow the installation instructions
below to prevent the product from overheating.
t The distance between the product and the
wall should be more than 10cm.
t Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
t Do not install the product on a carpet or
cushion.
t Make sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings
when watching the TV for long periods as the
ventilation openings may become hot. This
does not aect the operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on the power plug pins
or outlet. This may cause a re hazard.
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a
hand or sharp object such as nail, pencil or pen,
or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your
nger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
8
ENGLISH
When cleaning the product and its components,
unplug the power rst and wipe it with a soft
cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with
water or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives or
wax, benzene, alcohol etc., which can damage
the product and its panel. Otherwise, this may
result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn o this unit by SWITCH.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power
cord from the power board, as this could be
hazardous.
When moving the product, make sure you turn
the power o rst. Then, unplug the power
cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged,
which may create a re hazard or cause electric
shock.
When moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
If the product feels cold to the touch, there may
be a small “icker” when it is turned on. This is
normal, there is nothing wrong with product.
This panel is an advanced product that contains
millions of pixels. You may see tiny black dots
and/or brightly coloured dots (red, blue or
green) at a size of 1ppm on the panel. This does
not indicate a malfunction and does not aect
the performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
9
ENGLISH
You may nd dierent brightness and color
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
Displaying a still image for a prolonged period
of time may cause image sticking. Avoid
displaying a xed image on the TV screen for a
long period of time.
Generated Sound
“Cracking” noise: A cracking noise that
occurs when watching or turning o the TV
is generated by plastic thermal contraction
due to tempera-ture and humidity. This
noise is common for products where thermal
deformation is required. Electrical circuit
humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit,
which supplies a large amount of current to
operate a product. It varies depending on the
product.
This generated sound does not aect the
performance and reliability of the product.
Do not use high voltage electrical goods near
the TV (e.g. electric mosquito-swatter). This
may result in product malfunction.
Preparing
NOTE
t If the TV is turned on for the rst time
after it was shipped from the factory,
initialization of the TV may take a few
minutes. (Depending on model)
t Image shown may dier from your TV.
t Your TV’s OSD (On Screen Display) may dier
slightly from that shown in this manual.
t The available menus and options may dier
from the input source or product model that
you are using.
t New features may be added to this TV in the
future.
t The items supplied with your product may
vary depending on the model.
t Product specications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
t For an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the
USB cable or USB memory stick does not t
into your TV’s USB port.
A
B
A
B
*A
<
=
10 mm
*B
<
=
18 mm
t Use a certied cable with the HDMI logo
attached.
10
ENGLISH
t If you do not use a certied HDMI cable, the
screen may not display or a connection error
may occur. (Recommended HDMI Cable
Types)
- High-Speed HDMI
®
/
TM
cable (3 m or less)
- High-Speed HDMI
®
/
TM
cable with Ethernet
(3 m or less)
t How to use the ferrite core (Depending on
model)
- Use the ferrite core to reduce the
electromagnetic interference in the power
cord. Wind the power cord on the ferrite
core once.
[Wall side]
[TV side]
10 cm (+ / -2 cm)
t This Smart TV is for VOD watching
service, some smart functions may not be
supported including web browser. (Only
LH57**)
CAUTION
t Do not use any unapproved items to ensure
the safety and product life span.
t Any damage or injuries caused by using
unapproved items are not covered by the
warranty.
t Some models have a thin lm attached on
to the screen and this must not be removed.
t When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or at surface to protect
the screen from scratches.
t Make sure that the screws are fastened
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.) Do not use too
much force and over tighten the screws;
otherwise screw may be damaged and not
tighten correctly.
Lifting and moving
the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
t It is recommended to move the TV in
the box or packing material that the TV
originally came in.
t Before moving or lifting the TV, disconnect
the power cord and all cables.
t When holding the TV, the screen should
face away from you to avoid damage.
11
ENGLISH
t Hold the top and bottom of the TV
frame rmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
t When transporting a large TV, there should
be at least 2 people.
t When transporting the TV by hand, hold the
TV as shown in the following illustration.
t When transporting the TV, do not expose
the TV to jolts or excessive vibration.
t When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
t Do not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
t When handling the TV, be careful not to
damage the protruding buttons.
CAUTION
t Avoid touching the screen at all times, as
this may result in damage to the screen.
t Do not move the TV by holding the cable
holders, as the cable holders may break,
and injuries and damage to the TV may
occur.
Using the button
(Depending on model)
You can simply operate the TV functions,
pressing or moving the button.
NOTE
t LH57/59 series does not have a Joystick
functions but has only a power On/O
button.
Joystick Button
Dome Button
or
Basic functions
Power On (Press)
Power O (Press and
hold)
1
Volume Control
Programmes Control
1 All running apps will close, and any recording
in progress will stop.
12
ENGLISH
Adjusting the menu
When the TV is turned on, press the button
one time. You can adjust the Menu items
pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns
to TV viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a
table
1 Lift and tilt the TV into its upright position on
a table.
t Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
t Do not place the TV near or on sources
of heat, as this may result in re or other
damage.
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
t If there are bolts inserted at the eye-bolts
position, remove the bolts rst.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the at surface.
CAUTION
t Make sure that children do not climb on or
hang on the TV.
NOTE
t Use a platform or cabinet that is strong and
large enough to support the TV securely.
t Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
13
ENGLISH
Mounting on a wall
Attach an optional wall mount bracket at the
rear of the TV carefully and install the wall
mount bracket on a solid wall perpendicular
to the oor. When you attach the TV to other
building materials, please contact qualied
personnel. LG recommends that wall mounting
be performed by a qualied professional
installer. We recommend the use of LG’s wall
mount bracket. LGs wall mount bracket is
easy to move with cables connected. When
you do not use LGs wall mount bracket, please
use a wall mount bracket where the device is
adequately secured to the wall with enough
space to allow connectivity to external devices.
It is advised to connect all the cables before
installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are
described in the following table.
Separate purchase(Wall
mounting bracket)
Model
32/43LH57**
32/43LH59**
32/40/43LH60**
32/43LH61**
49LH57**
49LH59**
49/55LH60**
49/55LH61**
VESA (A x B)
(mm)
200 x 200 300 x 300
Standard
screw
M6 M6
Number of
screws
4 4
Wall mount
bracket
LSW240B
MSW240
LSW350B
MSW240
Model
55LH57**
55LH59**
VESA (A x B)
(mm)
400 x 400
Standard
screw
M6
Number of
screws
4
Wall mount
bracket
LSW440B
MSW240
A
B
14
ENGLISH
CAUTION
t Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
NOTE
t When installing the wall mounting bracket,
use the adhesive label or protective cover
provided. The adhesive label or protective
cover will protect the opening from
accumulating dust and dirt. (Only when the
label or cover is provided)
Provided item
Adhesive label
Provided item
Adhesive label
Provided item
Protective cover
t When installing the wall mounting bracket,
it is recommended to cover the stand hole
using tape, in order to prevent the inux of
dust and insects. (Depending on model)
Stand hole
t When attaching a wall mounting bracket
to the TV, insert the wall mount spacers
into the TV wall mount holes to adjust the
vertical angle of the TV. (Only when the
item of the following form is provided)
Provided
item
Wall mount
spacer
t Depending on the shape of the stand, use
a at tool to remove the stand cover as
illustrated below. (e.g., a at screwdriver)
(Only when the item of the following form is
provided)
Flat tool
15
ENGLISH
Connections
(notications)
Connect various external devices to the TV
and switch input modes to select an external
device. For more information of external devices
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
t The external device connection may dier
from the model.
t Connect external devices to the TV regardless
of the order of the TV port.
t If you record a TV program on a DVD recorder
or VCR, make sure to connect the TV signal
input cable to the TV through a DVD recorder
or VCR. For more information of recording,
refer to the manual provided with the
connected device.
t Refer to the external equipment’s manual for
operating instructions.
t If you connect a gaming device to the TV, use
the cable supplied with the gaming device.
t In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change the
PC output to another resolution, change the
refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu
until the picture is clear.
t In PC mode, some resolution settings may not
work properly depending on the graphics card.
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
t Use a signal splitter to use more than 2 TVs.
t If the image quality is poor, install a signal
amplier properly to improve the image
quality.
t If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
t An antenna cable and converter are not
supplied.
t Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV
mode.
t Check if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
t If the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
16
ENGLISH
USB connection
Some USB Hubs may not work. If a USB device
connected through a USB Hub is not detected,
connect it directly to the USB port on the TV.
Other connections
Connect your TV to external devices. For the
best picture and audio quality, connect the
external device and the TV with the HDMI cable.
Some separate cable is not provided.
NOTE
t Supported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192
kHz)
(Depending on model)
Remote control
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
To replace batteries, open the battery cover,
replace batteries (1.5 V AAA) matching
the
and ends to the label inside the
compartment, and close the battery cover. To
remove the batteries, perform the installation
actions in reverse.
Make sure to point the remote control toward
the remote control sensor on the TV.
A
B
1
2 3 4
5
6
7
A
(POWER) Turns the TV on or o.
Selects Radio, TV and DTV
programme.
1
,
4
(INPUT) Changes the input
source. (Depending on model)
1
,
4
Recalls your preferred
subtitle in digital mode. (Depending on
model)
2
(Q. Settings) Accesses the Quick
Settings. (Depending on model)
2
By pressing the AD button, audio
descriptions function will be enabled.
(Depending on model)
3
Views the information of the
current programme and screen. (Depending
on model)
3
By zooming in on the
selected area, you can view it in full screen.
(Depending on model)
3
Resizes an image. (Depending
on model)
17
ENGLISH
B
Number buttons Enters numbers.
Alphabet buttons Enters letters. (Depending
on model)
Accesses the saved programmes list.
(Space) Opens an empty space on the
screen keyboard. (Depending on model)
5
,
7
Shows programme guide.
(Depending on model)
5
Returns to the previously viewed
programme. (Depending on model)
Adjusts the volume level.
6
Views the information of the
current programme and screen. (Depending
on model)
6
,
7
(SEARCH) Search for content
such as TV programmes, movies and other
videos, or perform a web search by entering
text in the search bar. (Depending on model)
6
Accesses your favourite programme
list. (Depending on model)
(MUTE) Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next
screen.
C
D
8 9
10
11
12
14 15
16
13
C
8
Shows the previous history.
(Depending on model)
8
,
9
,
10
,
11
,
12
,
13
Teletext
buttons ( ) These buttons are
used for teletext. (Depending on model)
(HOME) Accesses the Home menu.
9
Shows the list of
Recommended, Programmes, Search and
Recorded. (Depending on model)
10
,
12
Returns to the previous level.
(Depending on model)
10
(Q. Settings) Accesses the Quick
Settings. (Depending on model)
11
,
13
Clears on-screen displays and
returns to TV viewing. (Depending on model)
11
Accesses the Quick menus.
(Depending on model)
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
Selects menus or options and conrms
your input.
18
ENGLISH
D
14
By pressing the AD button, audio
descriptions function will be enabled.
(Depending on model)
14
Views the information of the
current programme and screen. (Depending
on model)
15
Starts to record and displays
record menu. (Only Time Machine
Ready
supported model) (Depending on model)
15
By zooming in on the
selected area, you can view it in full screen.
(Depending on model)
15
Set the sleep timer. (Depending
on model)
15
Selects the MHP TV menu source.
(Depending on model)
16
Returns to LIVE TV. (Depending
on model)
Control buttons ( )
Controls media contents.
Coloured buttons These access special
functions in some menus.
(
: Red, : Green, : Yellow,
: Blue)
Licenses
Supported licenses may dier by model. For
more information about licenses, visit www.
lg.com.
Open source
software notice
information
To obtain the source code under GPL, LGPL,
MPL and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to opensource@lge.com.
This oer is valid for three (3) years from the
date on which you purchased the product.
19
ENGLISH
External control
device setup
To obtain the external control device setup
information, please visit www.lg.com.
Troubleshooting
Cannot control the TV with the remote control.
t Check the remote control sensor on the
product and try again.
t Check if there is any obstacle between the
product and the remote control.
t Check if the batteries are still working and
properly installed ( to , to ).
No image display and no sound is produced.
t Check if the product is turned on.
t Check if the power cord is connected to a
wall outlet.
t Check if there is a problem in the wall outlet
by connecting other products.
The TV turns o suddenly.
t Check the power control settings. The
power supply may be interrupted.
t Check if the
Sleep Timer / Timer Power
Off is activated in the TIMERS settings.
t Check if the Auto Power O is activated
in the General -> ECO MODE settings.
(Depending on model)
t If there is no signal while the TV is on,
the TV will turn o automatically after 15
minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’
or ‘Invalid Format’ is displayed.
t Turn the TV o/on using the remote control.
t Reconnect the HDMI cable.
t Restart the PC with the TV on.
20
ENGLISH
Specications
Wireless module specification
t As band channels can vary per country, the user cannot change or adjust the operating
frequency. This product is congured for the regional frequency table.
t For consideration of the user, this device should be installed and operated with a minimum
distance of 20 cm between the device and the body.
Wireless LAN module (TWFM-B006D) specifications
Standard IEEE802.11a/b/g/n
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
14 dBm
12.5 dBm
15.5 dBm
AC/DC Adapter
32LH57**, 32LH59**
Manufacturer : APD
Model : DA-48G19
Manufacturer : Lien Chang
Model : LCAP45
In : AC 100 - 240 V ~ 50/60 Hz
Out : DC 19 V
2.53 A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

LG 32LH570U El kitabı

Tip
El kitabı
Bu kılavuz için de uygundur

Diğer dillerde