LG 58UH635V El kitabı

Please read this manual carefully before operating your set and

retain it for future reference.

*MFL69361119*

www.lg.com

P/NO : MFL69361119(1604-REV01)

Printed in Korea

Safety and Reference

OWNER’S MANUAL

LED TV*

* LG LED TV applies LCD screen with LED

backlights.

2

ENGLISH

Safety instructions

Please read these safety precautions

carefully before using the product.

WARNING

Do not place the TV and/or remote control in

the following environments:

t A location exposed to direct sunlight

t An area with high humidity such as a

bathroom

t Near any heat source such as stoves and

other devices that produce heat

t Near kitchen counters or humidiers where

they can easily be exposed to steam or oil

t An area exposed to rain or wind

t Near containers of water such as vases

Otherwise, this may result in re, electric

shock, malfunction or product deformation.

Do not place the product where it might be

exposed to dust. This may cause a re hazard.

Mains Plug is the TV connecting/disconnecting

device to AC mains electric supply. This plug

must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands.

Additionally, if the cord pin is wet or covered

with dust, dry the power plug completely or

wipe dust o. You may be electrocuted due to

excess moisture.

Make sure to connect Mains cable to compliant

AC mains socket with Grounded earth pin.

(Except for devices which are not grounded

on earth.) Otherwise possibility you may be

electrocuted or injured.

Insert power cable plug completely into wall

socket otherwise if not secured completely into

socket, re ignition may break out.

Ensure the power cord does not come into

contact with hot objects such as a heater. This

may cause a re or an electric shock hazard.

Do not place a heavy object, or the product

itself, on power cables.

Otherwise, this may result in re or electric

shock.

ENGLISH

3

Bend antenna cable between inside and

outside building to prevent rain from owing

in. This may cause water damaged inside the

Product and could give an electric shock.

When mounting TV onto wall make sure to

neatly install and isolate cabling from rear of

TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a

single multiple electrical outlet. Otherwise, this

may result in re due to over-heating.

Do not drop the product or let it fall over when

connecting external devices. Otherwise, this

may result in injury or damage to the product.

Keep the anti-moisture packing material or

vinyl packing out of the reach of children.

Anti-moisture material is harmful if

swallowed. If swallowed by mistake, force

the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause

suocation. Keep it out of the reach of children.

Do not let your children climb or cling onto the

TV.

Otherwise, the TV may fall over, which may

cause serious injury.

Dispose of used batteries carefully to ensure

that a small child does not consume them.

Please seek Doctor- Medical Attention

immediately if child consumes batteries.

Do not insert any metal objects/conductors

(like a metal chopstick/cutlery/screwdriver)

between power cable plug and input Wall

Socket while it is connected to the input

terminal on the wall. Additionally, do not touch

the power cable right after plugging into the

wall input terminal. You may be electrocuted.

(Depending on model)

Do not put or store inammable substances

near the product. There is a danger of

combustion/explosion or re due to careless

handling of the inammable substances.

4

ENGLISH

Do not drop metallic objects such as coins,

hair pins, chopsticks or wire into the product,

or inammable objects such as paper and

matches. Children must pay particular

attention. Electrical shock, re or injury can

occur. If a foreign object is dropped into the

product, unplug the power cord and contact the

service centre.

Do not spray water on the product or scrub

with an inammable substance (thinner or

benzene). Fire or electric shock accident can

occur.

Do not allow any impact, shock or any objects

to fall into the unit, and do not drop anything

onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a

thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there

is leakage of gas, open the windows and

ventilate. It may cause a re or a burn by a

spark.

Do not disassemble, repair or modify the

product at your own discretion. Fire or electric

shock accident can occur.

Contact the service centre for check, calibration

or repair.

If any of the following occur, unplug the

product immediately and contact your local

service centre.

t The product has been impacted by shock

t The product has been damaged

t Foreign objects have entered the product

t The product produced smoke or a strange

smell

This may result in re or electric shock.

Unplug the TV from AC mains wall socket if you

do not intend to use the TV for a long period of

time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric

leakage/shock/re.

ENGLISH

5

Apparatus shall not be exposed to dripping or

splashing and no objects lled with liquids,

such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could

be exposed to oil or oil mist. This may damage

the product and cause it to fall.

If water enters or comes into contact with TV,

AC adapter or power cord please disconnect

the power cord and contact service centre

immediately. Otherwise, this may result in

electric shock or re.

Only use an authorized AC adapter and power

cord approved by LG Electronics. Otherwise, this

may result in re, electric shock, malfunction or

product deformation.

Never Disassemble the AC adapter or power

cord. This may result in re or electric shock.

Be careful in handling the adapter to prevent

any external shocks to it. An external shock may

cause damage to the adapter.

Make sure the power cord is connected securely

to the power plug on the TV. (Depending on

model)

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an

outside antenna and power lines to keep the

former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as

unstable shelves or inclined surfaces. Also avoid

places where there is vibration or where the

product cannot be fully supported. Otherwise,

the product may fall or ip over, which may

cause injury or damage to the product.

6

ENGLISH

If you install the TV on a stand, you need to

take actions to prevent the product from

overturning. Otherwise, the product may fall

over, which may cause injury.

If you intend to mount the product to a wall,

attach VESA standard mounting interface

(optional parts) to the back of the product.

When you install the set to use the wall

mounting bracket (optional parts), x it

carefully so as not to drop.

Only use the attachments / accessories specied

by the manufacturer.

When installing the antenna, consult with a

qualied service technician. If not installed by

a qualied technician, this may create a re

hazard or an electric shock hazard.

We recommend that you maintain a distance

of at least 2 to 7 times the diagonal screen size

when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could

cause damage to the remote control.

Do not mix new batteries with old batteries.

This may cause the batteries to overheat and

leak.

Batteries should not be exposed to excessive

heat. For example, keep away from direct

Sunlight, open replace and electric heaters.

Do not place non-rechargeable batteries in

charging device.

Make sure there are no objects between the

remote control and its sensor.

Signal from Remote Control can be interrupted

due to external/internal lighting eg Sunlight,

uorescent lighting. If this occurs turn o

lighting or darken viewing area.

ENGLISH

7

When connecting external devices such as

video game consoles, make sure the connecting

cables are long enough. Otherwise, the product

may fall over, which may cause injury or

damage the product.

Do not turn the product On/O by plugging-

in or unplugging the power plug to the wall

outlet. (Do not use the power plug for switch.)

It may cause mechanical failure or could give an

electric shock.

Please follow the installation instructions

below to prevent the product from overheating.

t The distance between the product and the

wall should be more than 10cm.

t Do not install the product in a place with

no ventilation (e.g., on a bookshelf or in a

cupboard).

t Do not install the product on a carpet or

cushion.

t Make sure the air vent is not blocked by a

tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings

when watching the TV for long periods as the

ventilation openings may become hot. This

does not aect the operation or performance of

the product.

Periodically examine the cord of your appliance,

and if its appearance indicates damage or

deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with

an exact replacement part by an authorized

servicer.

Prevent dust collecting on the power plug pins

or outlet. This may cause a re hazard.

Protect the power cord from physical or

mechanical abuse, such as being twisted,

kinked, pinched, closed in a door, or walked

upon. Pay particular attention to plugs, wall

outlets, and the point where the cord exits the

appliance.

Do not press strongly upon the panel with a

hand or sharp object such as nail, pencil or pen,

or make a scratch on it, as it may causedamage

to screen.

8

ENGLISH

Avoid touching the screen or holding your

nger(s) against it for long periods of time.

Doing so may produce some temporary or

permanent distortion/damage to screen.

When cleaning the product and its components,

unplug the power rst and wipe it with a soft

cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with

water or wipe with a wet cloth. Never use glass

cleaner, car or industrial shiner, abrasives or

wax, benzene, alcohol etc., which can damage

the product and its panel. Otherwise, this may

result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall

outlet, it is not disconnected from the AC power

source even if you turn o this unit by SWITCH.

When unplugging the cable, grab the plug and

unplug it, by pulling at the plug.

Don’t pull at the cord to unplug the power

cord from the power board, as this could be

hazardous.

When moving the product, make sure you turn

the power o rst. Then, unplug the power

cables, antenna cables and all connecting

cables.

The TV set or power cord may be damaged,

which may create a re hazard or cause electric

shock.

When moving or unpacking the product,

work in pairs because the product is heavy.

Otherwise, this may result in injury.

Refer all servicing to qualied service

personnel. Servicing is required when the

apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

If the product feels cold to the touch, there may

be a small “icker” when it is turned on. This is

normal, there is nothing wrong with product.

ENGLISH

9

This panel is an advanced product that contains

millions of pixels. You may see tiny black dots

and/or brightly coloured dots (red, blue or

green) at a size of 1ppm on the panel. This does

not indicate a malfunction and does not aect

the performance and reliability of the product.

This phenomenon also occurs in third-party

products and is not subject to exchange or

refund.

You may nd dierent brightness and color

of the panel depending on your viewing

position(left/right/top/down).

This phenomenon occurs due to the

characteristic of the panel. It is not related

with the product performance, and it is not

malfunction.

Displaying a still image for a prolonged period

of time may cause image sticking. Avoid

displaying a xed image on the TV screen for a

long period of time.

Generated Sound

“Cracking” noise: A cracking noise that

occurs when watching or turning o the TV

is generated by plastic thermal contraction

due to tempera-ture and humidity. This

noise is common for products where thermal

deformation is required. Electrical circuit

humming/panel buzzing: A low level noise is

generated from a high-speed switching circuit,

which supplies a large amount of current to

operate a product. It varies depending on the

product.

This generated sound does not aect the

performance and reliability of the product.

Do not use high voltage electrical goods near

the TV (e.g. electric mosquito-swatter). This

may result in product malfunction.

10

ENGLISH

Viewing 3D imaging (Only

3D models)

CAUTION

t Children should be supervised by an

adult when viewing 3D video. If a child

experiences eye fatigue, headaches or

blurred vision while watching 3D, they

should take a break, before they resume

watching 3D content.

t When viewing a 3D video, some may

experience discomfort such as a headache,

dizziness, fatigue, or blurred vision. In this

case, stop watching the 3D video and take

a rest.

t If you watch a 3D video for a long time, you

may experience eye fatigue. In this case,

stop watching the 3D video and take a rest.

t Only use LG 3D glasses. Otherwise, you may

not be able to view 3D videos properly.

t Do not use 3D glasses instead of your

normal glasses, sunglasses, or protective

goggles.

t Do not keep your 3D glasses in extremely

high or low temperatures. It will cause

deformation.

t Do not use 3D glasses while walking or

moving around. It may cause an accident or

injury.

t Be careful not to poke your eye with the

frames of the 3D glasses.

t Do not watch 3D content if you have

photosensitive seizures, epilepsy, or heart

disease.

Preparing

NOTE

t If the TV is turned on for the rst time

after it was shipped from the factory,

initialization of the TV may take a few

minutes.

t Image shown may dier from your TV.

t Your TV’s OSD (On Screen Display) may dier

slightly from that shown in this manual.

t The available menus and options may dier

from the input source or product model that

you are using.

t New features may be added to this TV in the

future.

t The items supplied with your product may

vary depending on the model.

t Product specications or contents of this

manual may be changed without prior

notice due to upgrade of product functions.

t For an optimal connection, HDMI cables

and USB devices should have bezels less

than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the

USB cable or USB memory stick does not t

into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

t Use a certied cable with the HDMI logo

attached.

t If you do not use a certied HDMI cable, the

screen may not display or a connection error

may occur. (Recommended HDMI Cable

Types)

ENGLISH

11

- High-Speed HDMI

®

/

TM

cable (3 m or less)

- High-Speed HDMI

®

/

TM

cable with Ethernet

(3 m or less)

t How to use the ferrite core (Depending on

model)

- Use the ferrite core to reduce the

electromagnetic interference in the power

cord. Wind the power cord on the ferrite

core once.

[Wall side]

[TV side]

10 cm (+ / -2 cm)

t Antenna Isolator Installation Guide

(Depending on model)

- Use this to install TV in a place where there

is a voltage dierence between TV Set and

GND of antenna signal.

»If there is a voltage difference between

TV Set and GND of antenna signal, the

antenna contact might be heated and

excessive heat might cause an accident.

- You can improve the safety when watching

TV by eciently removing power voltage

from TV antenna. It is recommended to

mount the isolator to the wall. If it cannot

be mounted to the wall, mount it on the

TV. Avoid disconnecting the antenna

Isolator after installation.

- Before starting, be sure that the TV

antenna is connected.

ANTENNA/

CABLE IN

Wall

Cable /

Antenna

or

Isolator

1. Connect to TV.

2. Connect to Set-Top box.

- Connect one end of the isolator to cable/

antenna jack and the other to TV set or

set-top box.

- “Equipment connected to the protective

earthing of the building installation

through the mains connection or through

other equipment with a connection

to protective earthing - and to a cable

distribution system using coaxial cable,

may in some circumstances create a re

hazard. Connection to a cable distribution

system has therefore to be provided

through a device providing electrical

isolation below a certain frequency range

(galvanic isolator, see EN 60728-11)”

- When applying the RF Isolator, a slight loss

of signal sensitivity can occur.

12

ENGLISH

CAUTION

t Do not use any unapproved items to ensure

the safety and product life span.

t Any damage or injuries caused by using

unapproved items are not covered by the

warranty.

t Some models have a thin lm attached on

to the screen and this must not be removed.

t When attaching the stand to the TV

set, place the screen facing down on a

cushioned table or at surface to protect

the screen from scratches.

t Make sure that the screws are inserted

correctly and fastened securely. (If they are

not fastened securely enough, the TV may

tilt forward after being installed.) Do not

use too much force and over tighten the

screws; otherwise screw may be damaged

and not tighten correctly.

t Make sure to wring any excess water or

cleaner from the cloth.

t Do not spray water or cleaner directly onto

the TV screen.

t Make sure to spray just enough of water or

cleaner onto a dry cloth to wipe the screen.

t When cleaning the product, be careful not

to allow any liquid or foreign objects to

enter the gap between the upper, left or

right side of the panel and the guide panel.

(Depending on model)

Separate purchase

Separate purchase items can be changed or

modied for quality improvement without any

notication. Contact your dealer to buy these

items. These devices only work with certain

models.

The model name or design may be changed

depending on the upgrade of product functions,

manufacturer’s circumstances or policies.

(Depending on model)

AG-F***

Cinema 3D Glasses

AN-MR650

Magic Remote

AN-VC550

Smart camera

AG-F***DP

Dual Play Glasses

Lifting and moving

the TV

Please note the following advice to prevent the

TV from being scratched or damaged and for

safe transportation regardless of its type and

size.

t It is recommended to move the TV in

the box or packing material that the TV

originally came in.

t Before moving or lifting the TV, disconnect

the power cord and all cables.

t When holding the TV, the screen should

face away from you to avoid damage.

ENGLISH

13

t Hold the top and bottom of the TV

frame rmly. Make sure not to hold the

transparent part, speaker, or speaker grill

area.

t When transporting a large TV, there should

be at least 2 people.

t When transporting the TV by hand, hold the

TV as shown in the following illustration.

t When transporting the TV, do not expose

the TV to jolts or excessive vibration.

t When transporting the TV, keep the TV

upright, never turn the TV on its side or tilt

towards the left or right.

t Do not apply excessive pressure to cause

exing /bending of frame chassis as it may

damage screen.

t When handling the TV, be careful not to

damage the protruding buttons.

CAUTION

t Avoid touching the screen at all times, as

this may result in damage to the screen.

t Do not move the TV by holding the cable

holders, as the cable holders may break,

and injuries and damage to the TV may

occur.

Using the button

(Depending on model)

You can simply operate the TV functions,

pressing or moving the button.

NOTE

t 43/49UH61, 43/49UH62 series does not

have a Joystick functions but has only a

power On/O button.

Joystick Button

Dome Button

or

Joystick Button

14

ENGLISH

Basic functions

Power On (Press)

Power O (Press

and hold)

1

Volume Control

Programmes

Control

1 All running apps will close, and any

recording in progress will stop.

Adjusting the menu

When the TV is turned on, press the button

one time. You can adjust the Menu items

pressing or moving the buttons.

Turns the power o.

Clears on-screen displays and returns

to TV viewing.

Changes the input source.

Accesses the settings menu.

Mounting on a

table

1 Lift and tilt the TV into its upright position

on a table.

t Leave a 10 cm (minimum) space from the

wall for proper ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

t Do not place the TV near or on sources

of heat, as this may result in re or other

damage.

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV

brackets and bolts on the back of the TV.

t If there are bolts inserted at the eye-bolts

position, remove the bolts rst.

2 Mount the wall brackets with the bolts to

the wall.

Match the location of the wall bracket and

the eye-bolts on the rear of the TV.

3 Connect the eye-bolts and wall brackets

tightly with a sturdy rope. Make sure to keep

the rope horizontal with the at surface.

CAUTION

t Make sure that children do not climb on or

hang on the TV.

NOTE

t Use a platform or cabinet that is strong and

large enough to support the TV securely.

t Brackets, bolts and ropes are not provided.

You can obtain additional accessories from

your local dealer.

ENGLISH

15

Mounting on a wall

Attach an optional wall mount bracket at the

rear of the TV carefully and install the wall

mount bracket on a solid wall perpendicular

to the oor. When you attach the TV to other

building materials, please contact qualied

personnel. LG recommends that wall mounting

be performed by a qualied professional

installer. We recommend the use of LG’s wall

mount bracket. LG’s wall mount bracket is

easy to move with cables connected. When

you do not use LG’s wall mount bracket, please

use a wall mount bracket where the device is

adequately secured to the wall with enough

space to allow connectivity to external devices.

It is advised to connect all the cables before

installing xed wall mounts.

10 cm

Make sure to use screws and wall mount

bracket that meet the VESA standard. Standard

dimensions for the wall mount kits are

described in the following table.

Separate purchase(Wall

mounting bracket)

Model

43UH61**

40/43UH62**

40UH63**

43UH65**

43UH66**

40/43UH67**

43UH74**

43UH75**

49/55UH61**

49/55UH62**

50UH63**

49/55UH65**

49/55UH66**

49/50/55UH67**

49/55UH74**

49/55UH75**

49/55UH77**

49/55UH79**

49/55UH80**

49/55UH84**

49/55UH85**

VESA (A x

B) (mm)

200 x 200 300 x 300

Standard

screw

M6 M6

Number

of screws

4 4

Wall

mount

bracket

LSW240B

MSW240

LSW350B

MSW240

16

ENGLISH

Model

60/65UH61**

60/65UH62**

58UH63**

60/65UH65**

60/65UH66**

58/60/65UH67**

60UH74**

60/65UH75**

60/65UH77**

60/65UH80**

60UH84**

60/65UH85**

70UH63**

75UH65**

70UH67**

70UH70**

75UH77**

75UH78**

75UH80**

75UH85**

79/86UH95**

VESA (A x

B) (mm)

300 x 300 600 x 400

Standard

screw

M6 M8

Number

of screws

4 4

Wall

mount

bracket

LSW350B LSW640B

Model 55/65UH95**

VESA (A x

B) (mm)

300 x 200

Standard

screw

M6

Number

of screws

4

Wall

mount

bracket

OTW420B

A

B

CAUTION

t Remove the stand before installing the TV

on a wall mount by performing the stand

attachment in reverse.

NOTE

t When installing the wall mounting bracket,

use the adhesive label or protective cover

provided. The adhesive label or protective

cover will protect the opening from

accumulating dust and dirt. (Only when the

label or cover is provided)

Provided item

Adhesive label

Provided item

Adhesive label

Provided item

Protective cover

ENGLISH

17

t When installing the wall mounting bracket,

it is recommended to cover the stand hole

using tape, in order to prevent the inux of

dust and insects. (Depending on model)

Stand hole

t When attaching a wall mounting bracket

to the TV, insert the wall mount spacers

into the TV wall mount holes to adjust the

vertical angle of the TV. (Only when the

item of the following form is provided)

Provided

Item

Wall Mount

Spacer

t Depending on the shape of the stand, use

a at tool to remove the stand cover as

illustrated below. (e.g., a at screwdriver)

(Only when the item of the following form

is provided)

Flat tool

Connections

(notications)

Connect various external devices to the TV

and switch input modes to select an external

device. For more information of external device’s

connection, refer to the manual provided with

each device.

Available external devices are: HD receivers, DVD

players, VCRs, audio systems, USB storage devices,

PC, gaming devices, and other external devices.

NOTE

t The external device connection may dier

from the model.

t Connect external devices to the TV regardless

of the order of the TV port.

t If you record a TV program on a DVD recorder

or VCR, make sure to connect the TV signal

input cable to the TV through a DVD recorder

or VCR. For more information of recording,

refer to the manual provided with the

connected device.

t Refer to the external equipment’s manual

for operating instructions.

t If you connect a gaming device to the TV, use

the cable supplied with the gaming device.

t In PC mode, there may be noise associated

with the resolution, vertical pattern, contrast

or brightness. If noise is present, change

the PC output to another resolution, change

the refresh rate to another rate or adjust

the brightness and contrast on the PICTURE

menu until the picture is clear.

t In PC mode, some resolution settings

may not work properly depending on the

graphics card.

18

ENGLISH

t If ULTRA HD content is played on your PC,

video or audio may become disrupted

intermittently depending on your PC’s

performance. (Depending on model)

Antenna connection

Connect the TV to a wall antenna socket with

an RF cable (75 Ω).

t Use a signal splitter to use more than 2 TVs.

t If the image quality is poor, install a signal

amplier properly to improve the image

quality.

t If the image quality is poor with an

antenna connected, try to realign the

antenna in the correct direction.

t An antenna cable and converter are not

supplied.

t Supported DTV Audio: MPEG, Dolby Digital,

Dolby Digital Plus, HE-AAC

t For a location that is not supported with

ULTRA HD broadcasting, this TV cannot

receive ULTRA HD broadcasts directly.

(Depending on model)

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite

socket with a satellite RF cable (75 Ω).

CI module connection

(Depending on model)

View the encrypted (pay) services in digital TV mode.

t Check if the CI module is inserted into the

PCMCIA card slot in the right direction. If

the module is not inserted properly, this can

cause damage to the TV and the PCMCIA

card slot.

t If the TV does not display any video and

audio when CI+ CAM is connected, please

contact to the Terrestrial/Cable/Satellite

Service Operator.

USB connection

Some USB Hubs may not work. If a USB device

connected using a USB Hub is not detected,

connect it to the USB port on the TV directly.

Other connections

Connect your TV to external devices. For the

best picture and audio quality, connect the

external device and the TV with the HDMI cable.

Some separate cable is not provided.

t

General HDMI

ULTRA HD Deep Colour

- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2,

4:2:0)

- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)

If the device connected to Input Port also

supports ULTRA HD Deep Colour, your picture

may be clearer. However, if the device doesn’t

support it, it may not work properly. In that

case, connect the device to a dierent HDMI

port or change the TV’s HDMI ULTRA HD

Deep Colour setting to Off.

(This feature is available on certain models

which are supported ULTRA HD Deep Colour

only.)

ENGLISH

19

NOTE

t Supported HDMI Audio format :

Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),

DTS (44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

(Depending on model)

Remote control

The descriptions in this manual are based on

the buttons on the remote control. Please read

this manual carefully and use the TV correctly.

To replace batteries, open the battery cover,

replace batteries (1.5 V AAA) matching the and

ends to the label inside the compartment, and

close the battery cover. To remove the batteries,

perform the installation actions in reverse.

Make sure to point the remote control toward

the remote control sensor on the TV.

(Depending on model)

A

B

2

1

3

4

5

A

(POWER) Turns the TV on or o.

Selects Radio, TV and DTV

programme.

(INPUT) Changes the input source.

(Q. Settings) Accesses the Quick Settings.

1

,

2

By zooming in on the

selected area, you can view it in full screen.

(Depending on model)

1

,

2

Views the information of the

current programme and screen. (Depending

on model)

1

(SEARCH) Search for content such as

TV programmes, movies and other videos, or

perform a web search by entering text in the

search bar. (Depending on model)

2

Recalls your preferred subtitle in

digital mode. (Depending on model)

Number buttons Enters numbers.

Accesses the saved programmes list.

(Space) Opens an empty space on the

screen keyboard.

3

Shows programme guide.

(Depending on model)

3

Returns to the previously viewed

programme. (Depending on model)

20

ENGLISH

B

4

Views the information of the

current programme and screen. (Depending

on model)

4

,

5

(SEARCH) Search for content such

as TV programmes, movies and other videos,

or perform a web search by entering text in

the search bar. (Depending on model)

4

,

5

Shows programme guide.

(Depending on model)

5

Used for viewing 3D video. (Depending

on model)

(MUTE) Mutes all sounds.

Adjusts the volume level.

 Scrolls through the saved programmes.

 Moves to the previous or next

screen.

C

D

RECENT

LIVE

MENU

6

7

8

9

10

C

Shows the previous history.

(HOME) Accesses the Home menu.

Shows the list of Recommended,

Programmes, Search and Recorded.

(Depending on model)

6

,

8

Returns to the previous level.

(Depending on model)

6

,

7

,

8

,

9

Teletext buttons (

) These buttons are used for

teletext. (Depending on model)

7

,

9

Clears on-screen displays and

returns to TV viewing. (Depending on model)

Navigation buttons (up/down/left/right)

Scrolls through menus or options.

Selects menus or options and conrms

your input.

D

By pressing the AD button, audio

descriptions function will be enabled.

10

Starts to record and displays

record menu.

(Only Time Machine

Ready

supported model)

(Depending on model)

10

By zooming in on the

selected area, you can view it in full screen.

(Depending on model)

10

Selects the MHP TV menu source.

(Depending on model)

Returns to LIVE TV.

Control buttons ( )

Controls media contents.

Coloured buttons These access special

functions in some menus.

( : Red, : Green, : Yellow,

: Blue)

Sayfa yükleniyor ...

LG 58UH635V El kitabı

LG 58UH635V El kitabı

Diğer dillerde

İlgili Makaleler