Dell PowerConnect 2808 Hızlı başlangıç Kılavuzu

Dell™ PowerConnect™ 28xx Systems

Getting Started Guide

Handbuch zum Einstieg

Guide de mise en route

Guía de introducción

Panduan Pengaktifan

͐ᮢ⦦ᆙ྆֡

ֵ⭞ޛ䰞᤽঍

⎆⠻#◲ᅞ⇆

ƸơǊƴ

Başlangıç Kılavuzu

Dell™ PowerConnect™ 28xx Systems

Getting Started Guide

Notes, Notices, and Cautions

NOTE:

A NOTE indicates important information that helps to make better use of the device.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and gives information how to avoid

the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, Dell OpenManage, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, PowerConnect, PowerApp,

PowerVault, Axim, DellNet, and Latitude are trademarks of Dell Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

November 2008 P/N. G536K Rev.

A02

Contents 3

Contents

1 Installation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . 5

Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Mounting the Device

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . 7

Device Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing on a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing on a Wall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Starting and Configuring the Device

Management Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting the Device to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 12

Connecting the Terminal to the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 13

Booting the Device - Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 13

Initial Configuration - Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . 15

Web Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . 18

The Newly Introduced Eco-Friendly Feature: Green Ethernet . . . . . . . . . . . .

19

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . 20

información NOM (únicamente para México). . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Informação sobre Órgão Regulador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4 Contents

Installation

5

Installation

Overview

This document provides basic information to install and start running the following PowerConnect

2800 series of Web-managed Gigabit Ethernet switches:

• PowerConnect 2808

• PowerConnect 2816

• PowerConnect 2824

• PowerConnect 2848

The PowerConnect 2800 series can be used to connect workstations and other network devices, such

as:

•Servers

•Hubs

•Routers

The PowerConnect devices are primarily intended for the Small Office/Home Office (SOHO) that

require high performance edge connectivity. These PowerConnect devices are ideal for the small to

medium business that requires high performance network connectivity along with advanced web

management features. The PowerConnect management features are designed to minimize

administrative management effort, while enhancing and improving network traffic control.

The switch is delivered from the factory in Unmanaged Mode. If users wish to use the switch as an

unmanaged switch, they can simply plug the switch in and start using it. No configuration is

necessary. If the same user wishes to use the switch as a managed switch, they need to change the

mode from Unmanaged to Managed, as described in the Dell™ PowerConnect™ 2800 Series User’s

Guide, available on the Documentation CD. Alternatively, you may check the Dell support website

at www.support.dell.com for the latest documentations and software updates.

Site Preparation

Site Requirements

The PowerConnect 2808/16/24/48 devices can be mounted in a standard equipment rack, placed on

a tabletop, or mounted on the wall.

6

Installation

Before installing the device, verify that the site selected for the device meets the following site

requirements:

•

Power

— The device is installed within 1.5 m (5 feet) of a grounded, easily accessible outlet 220/110

VAC, 50/60 Hz.

•

General

— Ensure that the power supply is correctly installed.

•

Clearance

— There is adequate frontal clearance for operator access. Allow clearance for cabling,

power connections, and ventilation.

•

Cabling

— Cabling is routed to avoid sources of electrical noise such as radio transmitters, broadcast

amplifiers, power lines, and fluorescent lighting fixtures.

•

Ambient Requirements

— The ambient device operating temperature range is 0 to 45 °C (32 to

113 °F) at a relative humidity of up to 95%, non-condensing. Verify that water or moisture cannot enter

the device case.

Unpacking

Package Contents

While unpacking the device, ensure that the following items are included:

• The device

• AC power cable

• Self-adhesive rubber pads (for on-shelf installation)

• Rack-mount kit for installation

• Documentation CD

• Product Information Guide

Unpacking the Device

To unpack the PowerConnect device:

NOTE:

Before unpacking the device, inspect the packaging and report any evidence of damage.

1

Place the box on a clean flat surface.

2

Open the box or remove the box top.

3

Carefully remove the device from the package and place it on a secure, stable and clean surface.

4

Remove all packing material.

5

Inspect the product for damage. Report any damage immediately.

Mounting the Device

7

Mounting the Device

Overview

The following mounting instructions apply to the PowerConnect 2808/16/24/48 devices. There are

three device mounting options:

• Installing in a Rack

• Installing on a Flat Surface

• Installing on a Wall

Installation Precautions

CAUTION Before performing any of the following procedures, read and follow the safety instructions

located in your Product Information Guide.

CAUTION Observe the following points before performing the procedures in this section:

• Ensure that the rack or cabinet housing the device is adequately secured to prevent it from

becoming unstable and/or falling over.

• Ensure that the power source circuits are properly grounded.

• Observe and follow the service markings. Do not service any device except as explained in the

system documentation. Opening or removing covers marked with a triangular symbol with a

lighting bolt may cause electrical shock. These components are to be serviced by trained service

technicians only.

• Ensure that the power cable, extension cable, and/or plug is not damaged.

• Ensure that the device is not exposed to water.

• Ensure that the device is not exposed to radiators and/or heat sources.

• Ensure that the cooling vents are not blocked.

• Do not push foreign objects into the device, as it may cause a fire or electric shock.

• Use the device only with approved equipment.

• Allow the device to cool before removing covers or touching internal equipment.

8

Mounting the Device

• Ensure that the device does not overload the power circuits, wiring, and over-current protection. To

determine the possibility of overloading the supply circuits, add together the ampere ratings of all

devices installed on the same circuit as the device. Compare this total with the rating limit for the

circuit.

• Do not install the device in an environment where the operating ambient temperature might exceed

40ºC (104ºF).

• Ensure that the airflow around the front, sides, and back of the device is not restricted.

Device Rack Installation

CAUTION:

Read the safety information in the Product Information Guide as well as the safety information for

other devices that connect to or support the device.

CAUTION:

Disconnect all cables from the device before mounting the device in a rack or cabinet.

CAUTION:

When mounting multiple devices into a rack, mount the devices from the bottom up.

Install the device in a rack as follows:

1

Place the supplied rack-mounting bracket on one side of the device ensuring the mounting holes on

the device line up to the mounting holes on the rack mounting bracket. The following figure illustrates

where to mount the brackets.

Figure 2-1. Bracket Installation for Rack Mounting

2

Insert the supplied screws into the rack mounting holes and tighten with a screwdriver.

3

Repeat the process for the rack-mounting bracket on the other side of the device.

Mounting the Device

9

4

Insert the device into the rack, ensuring the rack-mounting holes on the device line up to the

mounting hole on the rack.

5

Secure the device to the rack with the rack screws (not provided). Fasten the lower pair of screws before

the upper pair of screws. Ensure that the ventilation holes are not obstructed.

Installing on a Flat Surface

The device can be installed on a flat surface if it is not installed on a rack. The surface must be able to

support the weight of the device and the device cables.

1

Attach the self-adhesive rubber pads (provided with the device) on each marked location on the

bottom of the chassis.

2

Set the device on a flat surface, while leaving 2 inches (5.08 cm) on each side and 5 inches (12.7 cm) at

the back.

3

Ensure that the device has proper ventilation.

Installing on a Wall

To mount the device on a wall:

1

Ensure that the mounting location meets the following requirements:

• The surface of the wall must be capable of supporting the device.

• Allow at least 2 inches (5.1 cm) space on the sides for proper ventilation and 5 inches (12.7 cm) at

the back for power cable clearance.

• The location must not be exposed to direct sunlight.

• The location must be at least 2 feet (61 cm) away from any heating vents, and no area-heating

vent should point towards the device.

• The location must be ventilated to prevent heat buildup.

• Do not locate the device near any data or electrical cabling.

• The power cable must be able to reach an outlet.

2

Place the supplied wall-mounting bracket on one side of the device, ensuring that the mounting holes

on the device line up to the mounting holes on the wall-mounting bracket. The following figure

illustrates where to mount the brackets.

10

Mounting the Device

Figure 2-2. Bracket Installation for Wall Mounting

3

Insert the supplied screws into the wall-mounting bracket holes and tighten with a screwdriver.

4

Repeat the process for the wall-mounting bracket on the other side of the device.

5

Place the device on the wall in the location where the device is being installed.

6

On the wall mark the locations where the screws to hold the device must be prepared.

7

On the marked locations, drill the holes and place all plugs (not provided) in the holes.

8

Secure the device to the wall with screws (not provided). Ensure that the ventilation holes are not

obstructed.

Mounting the Device

11

Figure 2-3. Mounting Device on a Wall

12

Mounting the Device

Starting and Configuring the Device

13

Starting and Configuring the Device

After completing all external connections, proceed as follows:

• If the device is to be used as an unmanaged switch, there is no need for a terminal connection.

• A terminal connection is useful if the device is to be used in a managed mode.

NOTE:

Before proceeding, read the release notes for this product. The release notes can be downloaded

from h

http://support.dell.com

.

NOTE:

It is recommended that you obtain the most recent revision of the user documentation from the Dell

support website at h

http://support.dell.com

.

Management Modes

The PowerConnect 2808/16/24/48 has a Mode push button on the front panel. The Mode button

changes between Managed and Unmanaged modes, or changes from Secure to Managed modes.

Connecting the Device to the Network

To connect to an uplink port, use Category 6 Shielded Twisted-Pair (STP) cables with RJ-45

connectors at both ends. The RJ-45 ports on the Ethernet device support automatic Media-

Dependent Interface/Media-Dependent Interface with internal crossover wiring (MDI/MDIX).

Standard straight-through twisted-pair cables can be used to connect to any other Ethernet network

(systems, servers, switches or routers).

NOTICE:

Do not plug a phone jack connector into an RJ-45 port. This will damage the Ethernet device. Use

only twisted-pair cables with RJ-45 connectors that conform with FCC standards.

To connect the device to the network:

1

Attach one end of a Twisted-Pair cable to the device’s RJ-45 connector and the other end to a

switch or server.

2

Make sure each twisted pair cable does not exceed 328 feet (100 meters) in length.

As each connection is made, the link LED corresponding to each port on the device is illuminated

(green or amber) indicating that the connection is valid.

14

Starting and Configuring the Device

Connecting the Terminal to the Device

The device provides an external console port in models 2816/24/48. The console port enables a

connection to a terminal desktop system running terminal emulation software for monitoring and

configuring the device.

The Console port connector is a male DB-9 connector, implemented as a data terminal equipment

(DTE) connector.

To use the Console port, the following is required:

• VT100 compatible terminal or a desktop or portable system with a serial port and running VT100

terminal emulation software.

• An RS-232 null-modem cable with a female DB-9 connector for the Console port and the appropriate

connector for the terminal.

To connect a terminal to the device Console port, perform the following:

1

Connect the supplied RS-232 crossover cable to the terminal running VT100 terminal emulation

software.

2

Ensure that the terminal emulation software is set as follows:

a

Select the appropriate serial port to connect to the console.

b

Set the data rate to 9600 baud.

c

Set the data format to 8 data bits, 1 stop bit, and no parity.

d

Set flow control to none.

e

Select VT100 for Emulation mode.

NOTE:

When using HyperTerminal with Microsoft® Windows 2000, Windows XP, or Windows Vista, ensure that

you have the latest service packs installed. With Windows 2000 Service Pack 2, the arrow keys function properly in

HyperTerminal’s VT100 emulation. Go to www.microsoft.com for information on Windows 2000, Windows XP, and

Windows Vista service packs.

3

Connect the female connector of the RS-232 crossover cable directly to the Console port on the

device, and tighten the captive retaining screws. The PowerConnect 2800 series Console port is located

on the back panel.

Booting the Device - Managed Mode

The procedure described in this section refers to the device when set to operate as a managed switch.

The PowerConnect 2808/16/24/48 models include a built-in dual purpose Mode Button. To change

between managed and unmanaged modes, press the Mode Button for less than seven seconds.

Once the device is set to operate as a managed switch the boot procedure can be monitored on the

connected terminal as follows:

1

Ensure that the device console port is connected to a VT100 terminal device or VT100 terminal

emulator via the device’s RS-232 crossover cable.

Starting and Configuring the Device

15

2

Attach the supplied standard AC power cable to the AC connector on the back panel of the device.

Figure 3-1. Connecting to PowerConnect 2800 Series Console Port

Figure 3-2. Attaching AC Power cable to device

3

Locate an AC power receptacle.

4

Deactivate the AC power receptacle.

5

Connect the device to the AC receptacle.

6

Activate the AC power receptacle.

7

After activating the AC power receptacle, confirm that the device is connected and operating correctly

by examining the LEDs on the front panel.

16

Starting and Configuring the Device

When the power is turned on with the local terminal already connected, the device goes through Power

On Self Test (POST). POST runs every time the device is initialized and checks hardware components to

determine if the device is fully operational before completely booting. If a critical problem is detected,

the program flow stops. If POST passes successfully, a valid executable image is loaded into RAM. POST

messages are displayed on the terminal and indicate test success or failure.

The boot process runs less than 45 seconds when in unmanaged mode, and about 90 seconds when in

other modes.

Initial Configuration - Managed Mode

The information and procedures described in this section apply to the device when it is configured as a

Managed Mode switch.

NOTE:

The switch is factory-set by default to Unmanaged Mode.

NOTE:

The initial simple configuration uses the following assumptions:

• The PowerConnect device was never configured before, and is in the same state as when it was received.

• The PowerConnect device booted successfully.

• The console connection is established and the console prompt is displayed on the screen of a VT100 terminal

device. (Press the <Enter> key several times to verify that the prompt displays correctly.)

The initial device configuration can be performed via the web management interface, or through the

Serial port. After initial configuration, the device can be managed either from the Serial port, or remotely

through an interface defined during the initial configuration.

The system prompts you to use the Set-up wizard when the device boots up for the first time in Managed

Mode, or if the configuration file is empty because the device is not configured. The Setup Wizard provides

guidance through the initial device configuration, and gets the device up and running as quickly as possible.

NOTE:

Obtain the following information from your network administrator before configuring the device:

• SNMP Community String and SNMP Management System IP address (optional).

• Username and Password.

• The IP address to be assigned to the VLAN 1 interface through which the device is to be managed (by default,

every external and internal port is a member of the VLAN 1)

• The IP subnet mask for the network

• The default gateway (next hop router) IP address for configuring the default route.

The Setup Wizard guides you through the initial device configuration, and gets the system up and running

as quickly as possible. You can skip using the setup wizard and configure the device manually through the

device CLI mode.

The Setup Wizard configures the following fields.

• SNMP Community String and SNMP Management System IP address (optional)

• Username and Password

• Device IP address

Starting and Configuring the Device

17

• IP subnet mask

• Default Gateway IP address

The Setup Wizard displays the following information:

Welcome to Dell Easy Setup Wizard.

The Setup Wizard guides you through the initial switch configuration,

and gets you up and running as quickly as possible. You can skip the

setup wizard, and enter CLI mode to manually configure the switch.

The system will prompt you with a default answer; by pressing enter,

you accept the default. You must respond to the next question to run

the setup wizard within 60 seconds, otherwise the system will

continue with normal operation using the default system

configuration.

Would you like to enter the setup wizard (you must answer this

question within 60 seconds)? (Y/N)[Y] Y

NOTE:

If you select not to use the Setup Wizard, you can access the Web inteface by using the default IP

address/mask (192.168.2.1/255.255.255.0).

NOTE:

You can exit the Setup Wizard at any time by entering [Ctrl+Z].

Wizard Step 1

The following information displays:

The system is not setup for SNMP management by default.

To manage the switch using SNMP (required for Dell Network Manager)

you can:

*Setup the initial SNMP Version 2 account now

*Return later and setup additional SNMP v1/v2 accounts

For more information on setting up SNMP accounts, please see the user

documentation.

Would you like to setup the SNMP management interface now? (Y/N)[Y] Y

Enter [N] to skip to Step 2.

Enter [Y] to continue the Set-up wizard. The following information displays:

To setup the SNMP management account you must specify the management

system IP address and the "community string" or password that the

particular management system uses to access the switch. The wizard

automatically assigns the highest access level [Privilege Level 15]

to this account.

18

Starting and Configuring the Device

You can use Dell Network Manager or CLI to change this setting, and

to add additional management systems. For more information on adding

management systems, see the user documentation.

To add a management station:

Please enter the SNMP community string to be used:

[Dell_Network_Manager]

Please enter the IP address of the Management System (A.B.C.D) or wildcard (0.0.0.0) to manage from

any Management Station:[0.0.0.0]

Wizard Step 2

The following information displays:

Now we need to setup your initial privilege (Level 15) user account.

This account is used to login to the CLI, Telnet and Web interface.

You may setup other accounts and change privilege levels later.

For more information on setting up user accounts and changing

privilege levels,see the user documentation.

To setup a user account:

Enter the user name<1-20>:[admin]

Please enter the user password:*****

Please reenter the user password:*****

Wizard Step 3

The following information displays:

Next, an IP address is setup.

The IP address is defined on the default VLAN,(VLAN #1). This is the

IP address you use to access the Telnet, Web interface, or SNMP

interface for the switch. To setup an IP address:

Please enter the IP address of the device (A.B.C.D):10.6.22.100

Please enter the IP subnet mask (A.B.C.D or nn):[255.255.255.224]

Wizard Step 4

The following information displays:

Finally, setup the default gateway.

Please enter the IP address of the gateway from which this network is

reachable(e.g. 192.168.1.1).Default gateway (A.B.C.D):[10.6.22.97]

Sayfa yükleniyor ...

Dell PowerConnect 2808 Hızlı başlangıç ​​Kılavuzu

Dell PowerConnect 2808 Hızlı başlangıç ​​Kılavuzu

Diğer dillerde

Dell PowerConnect 2808 Hızlı başlangıç Kılavuzu

Dell PowerConnect 2808 Hızlı başlangıç Kılavuzu