HOTPOINT/ARISTON RZAA 1 (TK) Kullanici rehberi

Marka: HOTPOINT/ARISTON

Modeli: RZAA 1 (TK)

Kategori: Buzdolabı-dondurucular

Tip: Kullanici rehberi

FREEZER - MODELS

RZAA 1 (TK)

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED:

To ensure that your freezer runs reliably and efficiently follow these steps.

Choose a location for your

freezer, away from any

heat sources and

allow adequate

ventilation - 30mm

/4 inch) gap above.

Level the freezer by

adjusting the front feet.

This will stop rocking or

vibration and keep the

door aligned.

Plug in and switch on.

Allow the freezer to cool

before placing food

inside.

The high temperature

light will stay on until the

freezer has cooled down.

All food in the freezer

should be covered.

Move the freezer into

position, using the sides

of the cabinet. Take care

to avoid damaging the

refrigerant circuit pipe

work on the rear.

Before plugging in and

switching on, leave the

freezer in its final

location for at least 15

minutes to allow it to

settle.

Read the rest of these instructions to get the best from your appliance

and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

STEP 1

STEP 2

STEP 3 STEP 4

STEP 5

SAFETY &

INSTALLATION CONTROLS USEFUL ADVICE

CLEANING &

MAINTENANCE

TROUBLESHOOTING

SERVICE &

GUARANTEE

Your freezer is now

working.

If after 24 hours your

freezer is not operating as

you want, refer to the

TROUBLESHOOTING

section.

STEP 6

For Your Safety

For your safety, read the following advice:

The freezer cooling system contains a small amount of gas which is environmentally

friendly but flammable. To avoid any risk :-

● Install the freezer following the installation instructions and ensure that

ventilation openings are kept clear of obstruction.

● Take care when installing or moving the freezer to avoid damaging the pipes

on the rear.

● If you suspect a leak, do not switch on the freezer, but open the windows and

doors to ventilate the room.

● Do not use any electrical devices inside the freezer, for instance for

defrosting.

● Do not use any mechanical devices for defrosting other than any which may

have been supplied with the freezer as they may cause damage.

● Only use this freezer for storing domestic foodstuffs.

When installing your freezer :-

● Ensure that the mains cable is not trapped underneath or behind the freezer

when you install or move it.

● Do not stack any other appliance on top of this freezer as they may

damage the freezer or become unstable.

When using your freezer :-

● Do not sit or stand on top of your freezer.

● Do not store poisonous, flammable or dangerous substances in your freezer.

● Do not use aerosol sprays for defrosting or cleaning your freezer.

If you sell the freezer, pass on this booklet to the new owner.

SAFETY &

INSTALLATION

Installation

Location & Air Circulation

Locate your freezer away from sources of heat e.g.

Cookers, Radiators, Direct Sunlight as extreme

temperature will affect its performance.

Allow a minimum 30mm (1

/4 inch) between the top of

the freezer and the underside of the worktop.

Providing you follow the recommended ventilation requirements you will :-

● Prolong the life of the freezer.

● Minimise the risk of condensation on the outside of the freezer.

● Minimise the running costs.

● Minimise operating sounds caused by vibration.

Minimum space required to open door

The freezer needs a space of 600mm (24 inches) in front to allow the door to

open.

When positioning the freezer next to a unit, a gap of 30mm (1

inch) can be left

at the hinge side of the door to allow the easy removal of furniture. If preferred

the freezer can be positioned so that a gap is not left.This will restrict how far the

door can be opened but the furniture can still be removed (see diagram below).

The door hinge side can be changed to make it easier to open (see ‘Door Reversal’

in the CLEANING & MAINTENANCE section).

SAFETY &

INSTALLATION

TOP VIEW

less than 30mm

30mm or more

600mm

30mm (1

/4 inch)

Installation

Levelling:

Level the freezer when it is in its final location by adjusting the front feet, until firm

contact is made with the floor. This will stop rocking or vibration and keep the door

aligned which helps the freezer run reliably and efficiently.

Before plugging in and switching on, leave the freezer standing in its final location for

at least 15 minutes to allow it to settle.

Fitting a Freezer under a Work Top

To minimise running costs Hotpoint recommend fitting a vent to the rear of your

worktop, which is available from Hotpoint Genuine Parts & Accessories Mail Order

Hotline (see KEY CONTACTS, back page).

WARNING: If there is less than 30mm clearance above the freezer, a vent must be

fitted to provide adequate ventilation above your freezer.

SAFETY &

INSTALLATION

Installation

Electrical Supply

WARNING: This appliance must be earthed.

The freezer must be positioned so that the plug is accessible after installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the

fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket

anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE :

Green/Yellow - Earth

Blue - Neutral Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with

the colour of the markings identifying terminals in the plug. You should therefore

wire it as shown above.

Changing the Mains Lead

This freezer is fitted with a special mains lead. If you need to replace the mains lead

due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS, back

page). It is strongly advised that this work is carried out by a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC

directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC

Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

SAFETY &

INSTALLATION

Controls

Controlling the Temperature of the Freezer Compartment

The control wheel on the front of the worktop adjusts the internal freezer

temperature. Your food should be maintained at -18˚C or colder for long term

storage.

The setting of the control wheel will depend on the location of the freezer, the room

temperature and how often the door is opened. The normal set point (marked by a 3

and N on the dial) is usually suitable. If you need to adjust the temperature turn the

control wheel:

Clockwise (higher number) - Colder

Anti-clockwise (lower number) - Warmer

You can check the temperature of the freezer compartment by using a Fridge Freezer

Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order

Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer, as breakage would cause a

health hazard.

Your freezer must NOT be placed in a room where the temperature goes below 2˚C or

above 38˚C for prolonged periods, as the internal freezer temperature will not be

maintained.

CONTROLS

Controls

CONTROLS

Indicator Lights

Green Mains Light

The green mains light will stay on as long as the electricity supply is not interrupted.

Red High Temperature Warning Light

The red temperature warning light will come on when the freezer is first switched on

or when the temperature inside the compartment rises above the correct storage

temperature. Check the TROUBLESHOOTING section before calling for advice. The

red light may come on for a short period when opening the freezer door to load or

unload food, in this case storage times will not be affected.

Useful Advice

Frozen food storage capacity 33kg

Maximum freezing capacity in 24 hours 15kg

Maximum conservation time from failure 18 hours

Making the best use of your Freezer

Note : Always use the handle provided to open the freezer door.

To ensure that your freezer operates as efficiently as possible :

● Follow food packaging “best before/use by” instructions or your suppliers

advice on a suitable maximum storage time.

● Keep foods tightly covered to retain moisture and prevent flavour/odour

transference. Plastic bags, aluminium foil, plastic stretch wrap and containers

with lids are ideal.

● Select chilled and frozen food last when shopping, transport in a ‘cool bag’

and place in freezer as soon as possible after arriving home.

● Avoid opening the door unnecessarily or for longer than needed.

● Allow hot or warm food to cool down in covered containers before placing in

freezer, as placing hot food inside reduces efficiency.

● Prepare fresh foods for freezing in small quantities to ensure that the food

freezes quickly and so that its quality does not deteriorate.

● Ensure that packets/containers of food are dry before freezing otherwise

they may freeze together.

Note:

The Rating Plate, which lists the appliance Model Number and Serial

Number can be found near the bottom of the left hand internal wall.

USEFUL ADVICE

Useful Advice

Storing Food in a Freezer

● Freeze and store either fresh food or long term commercially frozen foods.

● Generally speaking long term storage means up to 3 months but this can

vary, so always follow your supplier’s recommendations otherwise refer to

the pictorial guide on the door liner (see below).

● Place frozen food in the freezer compartment as soon as possible after

buying it.

● Liquid-filled bottles or sealed fizzy drinks must not be stored in freezer, as

they may burst.

● Lollipops and water ices should not be given to children directly from the

freezer the low temperature may cause ‘freezer burns’.

● Store ice cream towards the top front of the freezer and remove from freezer

15-30 minutes before serving.

● Ensure food is labelled and dated before placing in freezer.

● Do not allow fresh food to come into contact with food already frozen, the

frozen food could start to defrost.

● Once thawed, food should be cooked and eaten within 24 hours or cooked

and refrozen.

● Fully defrost your freezer when the ice is between 3-5mm thick (

inch) (see

CLEANING & MAINTENANCE section).

Note : A thick layer of ice will increase the running costs of your freezer.

USEFUL ADVICE

Useful Advice

Advice on Using Freezer Drawers

This freezer can be used with or without the drawers. However, the bottom drawer

needs to remain in position at all times (to maintain the correct storage temperature).

It is generally more convenient to use the drawers but if a lot of food is to be stored

the drawers can be taken out and food placed directly onto the grids.

Ensure that packets/containers of food are thoroughly dry before placing onto the

grids.

The storage drawers can be easily removed. Pull the drawer towards you until it

reaches it’s stop position. Hold securely on both sides, lift the front of the drawer to

release and remove.

For cleaning advice see CLEANING & MAINTENANCE section.

USEFUL ADVICE

When using the frozen food storage drawers, ensure that they are pushed fully back

before closing the door.

Food can be separated into different storage drawers for easy identification.

When lifting or removing the large deep drawer it is important to hold the side

handles and not the front handle.

WARNING: The freezer drawers can become heavy when fully loaded with food.

Care must be taken if attempting to lift or carry a full freezer drawer. It is

recommended to remove the required food, rather than the whole freezer drawer.

Note : It is important not to touch or move any of the freezer drawers/parts

with wet hands as it may cause freezer burn or discomfort.

Ice Tray

When making ice, use the tray provided. Take care not to overfill with water.

Uncovered food should not be placed near the ice tray as it can affect the flavour of

the ice.

Note : Empty, wash and refill the ice tray periodically to ensure freshness.

Defrosting

Regular use of your appliance causes ice to gradually build up on internal surfaces

increasing the running costs of your appliance. When the ice is between 3-5mm (

inch) Hotpoint recommend ‘fully defrosting your freezer’.

Fully defrosting your freezer.

WARNING: Switch off the electricity supply and pull out the mains plug.

1. Remove frozen food, wrap or cover and store in a cool place.

2. Remove the storage drawers

3. A defrost tube is stored in the floor of the freezer. Insert the tube into the

groove situated in the floor at the front of the freezer. Place a container

beneath the tube to collect the defrost water.

4. As the frost begins to melt, use the supplied plastic scraper to remove frost.

Never use sharp metal tools to remove frost as they may damage your

freezer beyond repair.

5. Sponge out excess defrost water which collects at the bottom of the freezer.

NOTE : When defrosting is complete, clean the interior thoroughly,

see CLEANING & MAINTENANCE section.

6. Replace storage drawers.

7. Replace mains plug and switch on. Unwrap food and replace.

CLEANING &

MAINTENANCE

Cleaning

WARNING: Switch off electrical supply and pull out mains plug before cleaning.

Interior

1. Remove food and wrap or cover to keep it frozen.

2. Remove drawers from each compartment and wash in warm water and

washing up liquid using a soft cloth, dry thoroughly.

Note : It is important to ensure that cleaned baskets are thoroughly dried

before refitting to the freezer compartment.

3. Wipe interior and fittings with a clean cloth wrung out in a solution of either

one teaspoon of bicarbonate of soda to one pint of water or Milton™

sterilising fluid, diluted according to the manufacturer’s instructions.

4. Dry interior thoroughly with a clean cloth before replacing fittings and food.

Exterior

Use a clean soft cloth wrung out in warm water and washing up liquid to wipe the

exterior surface, dry thoroughly.

WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish

to clean your freezer, they leave a smell in the freezer and can damage the

exterior.

Use a soft brush or vacuum cleaner to remove dust from underneath the freezer and

from the compressor and condenser situated at the back of the freezer.

WARNING: Do not damage the pipework.

Door Seal

Use warm water and a clean soft cloth to wipe along and in between the creases of

the door seal, dry thoroughly. Take care not to damage the seal and avoid using

sharp objects.

WARNING: Do not use detergent, it will damage the seal.

Going Away

If you are going away and don’t want to use your freezer, switch off electricity supply

and pull out the mains plug. Remove food and follow the defrosting and cleaning

instructions above.

Note : Leave the door ajar to prevent an accumulation of odours.

CLEANING &

MAINTENANCE

You will need a selection of small hand tools, screwdrivers, spanners etc. to carry out

this procedure.

Our Service Department can arrange for an Engineer to do the conversion for you but

a charge will be made.

Door Reversal

WARNING: Switch off electrical supply and pull out the mains plug.

Remove loose items/fittings from inside the fridge and place food into insulated

containers whilst carrying out this operation.

1. Open the door as wide as possible.

Note : You may require assistance to do this:

2. Support the door and using a screwdriver, remove the screw

securing the top hinge.

3. Carefully tilt the door to remove the hinge from the cabinet

and lift the door off the bottom hinge.

4. Remove the spacing washers from the bottom hinge.

Note : You may require assistance to do this:

5. Using the packaging from the appliance or a suitable substitute to support

the back of the appliance. Lay the appliance on it’s back ensuring the

pipework at the back is not damaged or bent. Be careful that the appliance

does not run away from you when the wheels touch the floor.

6. Unscrew the foot plate and hinge bracket fitted to the bottom right hand

side of the appliance. Unscrew the foot and footplate fitted to the bottom

left hand side of the appliance.

7. Refit the hinge bracket and the footplate to the opposite sides of the

appliance. Screw in the feet until there is approximately 35mm projecting

from the bottom front edge of the appliance.

8. Lift the appliance onto it’s feet.You may require assistance to do this:

Lift the appliance from the rear of the tabletop and stand it on it’s feet and

wheels. Be careful that the appliance does not run away from you when

the wheels touch the floor.

9. Using a thin blunt instrument, remove the hinge

bush cap from the top left of the door and refit on

the top right.

10. If applicable - using a screwdriver, remove the door

stop from the bottom right of the door and refit on

the bottom left.

Note : You may require assistance to do this:

11. Replace the top hinge onto the door, slide the door onto the bottom hinge

pin and support the door whilst screwing the top hinge into position. Ensure

that the top hinge bracket is positioned correctly.

12. Adjust the front feet (see ‘Levelling’SAFETY & INSTALLATION section).

Note : Let the appliance stand upright in it’s final location for at least 15

minutes before plugging in and switching on the electricity supply.

Maintenance

CLEANING &

MAINTENANCE

door stop

Troubleshooting

IS THE FREEZER WORKING AS YOU

WANT?

Have you read through the

instruction book ?

If you still have a problem, before

calling our service organisation see if

any of the tips below help.

The appliance will not work

1. Check plug is firmly positioned in the

socket outlet and the power supply is

switched on.

2. Check power supply with another

appliance.

3. Check fuse/circuit breaker.

4. Check the door is closed properly.

The appliance is making a lot of noise

1. Check that the rear pipe work is clear

of the wall, skirting board and other

obstacles.

2. Check that all four feet/wheels are

firmly in contact with the floor and

level.

3. See ‘Operating Sounds’ overleaf.

The freezer is too warm

1. Turn the control wheel to a higher

number. See CONTROLS section.

2. If the appliance is close to a heat

source, move it to another location.

3. Check that there is enough

ventilation around the appliance.

4. Check door has been closed properly.

The freezer is too cold

1. Turn the control wheel to a lower

number. See CONTROLS section.

The red warning light will not go out

1. Has the appliance just been

installed? (This is normal and the

light will go out when the correct

temperature has been reached).

2. Has the appliance just been loaded

with a large quantity of food. (The

light will go out once all the food has

reached the correct temperature).

3. Check door has been closed properly.

There has been a power failure

WARNING: Do not open the freezer

compartment door.

If power failure lasts longer than the

maximum conservation time (18 hrs),

food should either be cooked and eaten

with 24 hours or cooked and refrozen.

The freezer door is difficult to open

A well sealed freezer door can be difficult

to open. This is partly due to the

difference in temperature between the

room and internal freezer compartment.

If you have just closed the freezer door, it

maybe particularly difficult to open again

immediately. Wait 5 minutes for the

internal and external pressure to equalise

and try again.

Ice builds up rapidly inside the freezer

1. Check that nothing is stopping the

door from closing properly.

2. Check that foods and liquids are

covered to avoid the build up of

moisture inside.

3. See ‘Defrosting’in the CLEANING &

MAINTENANCE section for advice.

The door will not close

1. Check to see if the appliance has a

build up of ice which is stopping the

door closing. If this is the case refer to

‘Defrosting’in the CLEANING &

MAINTENANCE section and defrost

the appliance.

If there is still a problem contact

Hotpoint Service (see KEY CONTACTS

back cover).

TROUBLESHOOTING

Troubleshooting

OPERATING SOUNDS OF A FRIDGE FREEZER

These are the normal types of sound that your freezer will make.

The motor (compressor) makes a buzzing or humming sound when it is

running. This can be louder when it first switches on. This sound will

reduce over the first few months.

Gases flowing through the pipes can produce gurgling, bubbling,

roaring or humming noises.

The temperature control can make a clicking noise when it turns the

motor on and off.

Expansion and contraction of parts inside the freezer can produce a

cracking noise as they rapidly change temperature.

●

TROUBLESHOOTING

DONDURUCU - FZAA 1 (TK)

MODELLERİ

BAŞLARKEN :

Dondurucunuzun güvenli ve verimli bir şekilde çalışmasını istiyorsanız, aşağıdaki adımlara uyun.

Cihazınızdan en iyi şekilde yararlanmak için kalan talimatları da okuyun ve

garanti kayıt formunu doldurmayı unutmayın.

Bu Kılavuzu, çabuk erişebileceğiniz güvenli bir yerde tutun.

1. ADIM:

2. ADIM:

Dondurucunuzu, ısı

Dondurucuyu yanlarından

kaynaklarından uzak ve

tutarak yerine yerleştirin.

havalandırması yeterli bir

Arka tarafta bulunan

yere koyun – yukarıdan

soğutma devresi

boşluk 30 mm (11/4 inch)

borusuna hasar

vermemeye özen gösterin.

3. ADIM: 4. ADIM:

Ön ayağını ayarlayarak

Fişe takmadan ve

dondurucuyu dengeleyin.

çalıştırmadan önce,

Bu sallantı ve titreşimi

dondurucunun yerine

önlemekle birlikte

iyice oturması için 15

kapının düzgün bir

dakika bekleyin.

şekilde açılmasını sağlar.

5. ADIM:

6. ADIM:

Fişe takın ve açın.

Yiyecekleri yerleştirmeden

önce, dondurucunun

Artık dondurucunuz

soğumasını bekleyin.

çalışmaya hazır. 24 saat

Yüksek sıcaklık ışığı,

sonunda, dondurucunuz

dondurucu soğuyana

istediğiniz şekilde

kadar açık kalır.

çalışmazsa, SORUN

Dondurucudaki tüm

GİDERME bölümüne bakın.

yiyeceklerin üzeri

kapatılmalıdır.

GÜVENLİK VE

KURULUM

KONTROL FAYDALI BİLGİLER

TEMİZLEME VE

BAKIM İŞLEMİ

SORUN GİDERME

SERVİS VE

GARANTİ

Güvenliğiniz İçin

Güvenliğiniz için, aşağıdaki tavsiyelere uyun:

Dondurucunun soğutma sisteminde, az miktarda çevre dostu ancak yanıcı gaz bulunur.

Riskleri önlemek için:

Dondurucuyu aşağıdaki kurulum talimatlarından yararlanarak kurun ve

havalandırma deliklerini tıkanmamaları için temiz tutun.

Dondurucuyu kurarken veya hareket ettirirken, arka tarafta bulunan boruların

hasar görmemesine özen gösterin.

Sızıntı olduğundan şüphelenirseniz, dondurucuyu çalıştırmayın. Odayı

havalandırmak için pencereleri ve kapıları açın.

Dondurucunun içinde, buz çözmek gibi işlemler için elektrikli cihaz

kullanmayın.

Buz çözme işlemi için dondurucu ile birlikte verilenler dışında hiçbir mekanik

cihaz kullanmayın, aksi takdirde dondurucu hasar görebilir.

Bu dondurucuyu sadece evde yapılan yiyecekler için kullanın.

Dondurucuyu kurarken:

Dondurucuyu kurduğunuzda veya hareket ettirdiğinizde, şebeke kablosunun

dondurucunun altında veya arkasında sıkışmasını engelleyin.

Dondurucunun üzerine cihaz koymayın. Dondurucuya hasar verebilir veya

dondurucunun üzerinden düşebilir.

Dondurucuyu kullanırken:

Dondurucuya oturmayın veya yaslanmayın.

Dondurucunuzda zehirli, yanıcı veya tehlikeli maddeleri saklamayın.

Dondurucunuzun buzunu çözerken veya temizlerken sprey kullanmayın.

Dondurucuyu sattığınız takdirde, bu kılavuzu da yeni sahibine vermeyi unutmayın.

GÜVENLİK VE

KURULUM

Kurulum

Konum ve Hava Sirkülasyonu

Aşırı ısı dondurucunuzun performansını etkileyeceğinden,

dondurucunuzu Ocak, Radyatör, Direkt Gün Işığı gibi ısı

kaynaklarından uzak bir yere yerleştirin.

Dondurucunun üst kısmı ve tezgahın alt kısmı arasında

en az 30 mm (11/4 inç) boşluk bırakın.

Havalandırma tavsiyelerine uyduğunuz takdirde:

Dondurucunuzun ömrünü uzatırsınız.

Dondurucunun dışında oluşabilecek buğulanma riskini azaltırsınız..

Kullanım masraflarını azaltırsınız.

Çalışma sonucu titreşimden kaynaklanan sesleri azaltır.

Kapıyı açmak için gereken minimum boşluk

Dondurucunun kapısının açılması için ön tarafta gereken boşluk 60 mm’dir (24 inç).

Dondurucuyu bir ünitenin yanına yerleştirirken, mobilyanın rahatça çıkarılabilmesi için

kapının menteşe tarafından 30 mm (11/4 inç) boşluk bırakılabilir. Tercih edilirse,

dondurucu boşluk bırakılmadan yerleştirilebilir. Bu kapının açılma açısını etkiler, ancak

mobilya yine de yerinden çıkarılabilir (bkz. aşağıdaki tablo). Kapının menteşe tarafı,

daha rahat açılmasını sağlamak amacıyla değiştirilebilir (bkz. TEMİZLEME ve BAKIM

bölümünde ‘Kapının Ters Tarafa Açılması’ konu başlığı).

GÜVENLİK VE

KURULUM

ÜSTTEN GÖRÜNÜM

30 mm’den daha az

30mm veya daha fazla

600mm

30mm (1

/4 inç)

Kurulum

Dengeleme:

Dondurucu iyice yerleştirildikten sonra, yere sıkı bir şekilde temas edene kadar ön ayaklarını

ayarlayarak dengede durmasını sağlayın. Bu sallantı ve titreşimi önleyerek ve kapının

hizalanmasını sağlayarak, dondurucunun güvenli ve verimli bir şekilde çalışmasını sağlar.

Fişe takmadan ve çalıştırmadan önce, dondurucunun yerine iyice oturması için 15 dakika

bekleyin.

Dondurucunun tezgahın altına yerleştirilmesi

Kullanım masraflarını en aza indirilmesi için Hotpoint tezgahın arka tarafına bir

havalandırma takılmasını önerir. Bu havalandırmayı Orijinal Parçalar ve Aksesuarlar Posta

ile Sipariş Yardım Hattı’ndan (bkz. ÖNEMLİ İRTİBATLAR, arka sayfa) edinebilirsiniz.

UYARI: Dondurucunun üzerinde 30 mm’den az bir boşluk varsa, dondurucunuzun

üzerine yeterli havalandırma sağlayacak bir havalandırma takılmalıdır.

GÜVENLİK VE

KURULUM

Kurulum

Güç Kaynağı

UYARI: Cihaz mutlaka topraklanmalıdır.

Dondurucu, kurulumdan sonra da prize erişebilecek şekilde yerleştirilmelidir.

Sigortalar

Cihazınızda, bir fiş ve 13A’lık bir sigorta bulunmaktadır. Sigortayı değiştirmeniz

gerekirse, sadece 13A'lık ve BS1362 onaylı ASTA kullanın.

Fişin Değiştirilmesi

Prizinize uymadığı takdirde, cihazla birlikte verilen fişi kesin ve atın.

UYARI: Elektrik çarpmasını engellemek için, atılan fişi başka yerdeki soketlere de

takmayın.

GÜÇ KABLOSUNDAKİ ÖNEMLİ TELLER, AŞAĞIDA VERİLEN KODLARA GÖRE

RENKLENDİRİLMİŞTİR:

Yeşil/Sarı - Topraklı

Mavi - Nötr Kahverengi - Canlı

Fişi değiştirmeniz durumunda, güç kablosundaki teller fişteki bağlantı uçlarını tanımlayan

işaretlerin rengine karşılık gelmeyebilir. Bu nedenle, kabloları yukarıda gösterildiği

şekilde bağlamanız gerekir.

Güç Kablosunun Değiştirilmesi

Bu dondurucuda özel bir güç kablosu takılıdır. Gördüğü hasar nedeniyle değiştirilmesi

gereken güç kablosunu Hotpoint Servis’ten (bkz. ÖNEMLİ İRTİBATLAR, arka sayfa)

temin edebilirsiniz. Değiştirme işleminin, işi bilen bir elektrik teknisyeni tarafından

yapılması önemle tavsiye edilir.

CE İşareti, cihazın aşağıdaki EEC direktiflerine uygun olduğunu göstermektedir:

Alçak Gerilim Ekipmanları - 72/23/EEC ve 93/68 EEC Elektromanyetik

Uyumluluk - 89/336/EEC, 92/31/EEC ve 93/68/EEC

GÜVENLİK VE

KURULUM

-AtýkElektrikliveElektronikEþyalarýn(AEEE)Kontrolü

Yönetmeliðineuygundur.

Sayfa yükleniyor...

HOTPOINT/ARISTON RZAA 1 (TK) Kullanici rehberi

Marka: HOTPOINT/ARISTON

Modeli: RZAA 1 (TK)

Kategori: Buzdolabı-dondurucular

Tip: Kullanici rehberi

PDF''yi indir

rapor

diğer dillerde

English: HOTPOINT/ARISTON RZAA 1 (TK) User guide

HOTPOINT/ARISTON RZAA 1 (TK) Kullanici rehberi

HOTPOINT/ARISTON RZAA 1 (TK) Kullanici rehberi

diğer dillerde

Diğer belgeler