Yamaha MCX-A10 El kitabı

DIGITAL AUDIO TERMINAL MCX–A10

100_Musiccast_E.p65 2003.06.28, 19:011

3

Compliance with FCC regulations does not

guarantee that interference will not occur in all

installations. If this product is found to be the

source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to

eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial

type cable.

If these corrective measures do not produce

satisfactory results, please contact the local

retailer authorized to distribute this type of

product. If you can not locate the appropriate

retailer, please contact Yamaha Electronics Corp.,

U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

1.

IMPORTANT NOTICE : DO NOT MODIFY

THIS UNIT!

This product, when installed as

indicated in the instructions contained in this

manual, meets FCC requirements. Modifications

not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with

this product MUST be used. Follow all

installation instructions. Failure to follow

instructions could void your FCC authorization to

use this product in the USA.

3. NOTE : This product has been tested and found

to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not

result in harmful interference with other

electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other

electronic devices.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade

or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

FCC INFORMATION (for US customers only)

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been

dropped.

100_Musiccast_E.p65 2003.06.28, 19:023

4

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. Avoid ventilation space of at least 30 cm

on the top, 20 cm on the left and right.

• Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

• Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

• Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do NOT place:

• Other components, as they may cause damage and/or

discoloration on the surface of this unit.

• Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

• Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

• Do not cover the rear panel of this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct heat radiation.

If the temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

• Do not plug this unit in to a wall outlet until all connections

are complete.

• Do not operate this unit upside-down. It may overheat,

possibly causing damage.

• Do not use force on switches, knobs and/or cords.

• When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

• Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

• Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

• To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

• Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reasons.

• When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

• Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

• Before moving this unit, press STANDBY/ON to place the

unit in standby mode, and disconnect the AC power plug from

the wall outlet.

• Be sure to use the AC adaptor (LSE0107A1240) supplied with

this unit. Otherwise, you might cause a fire or damage to this

unit.

• This unit is designed for home use only. Never use this unit in

a car, etc., otherwise it may cause a malfunction of this unit.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

IMPORTANT!

Please record the serial number of this unit in the space

below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT

The wires in this mains lead are colored in accordance with

the following code:

GREEN-and-YELLOW:Earth

BLUE:Neutral

BROWN:Live

As the colors of the wires in the mains lead of this apparatus

may not correspond with the colored markings identifying

the terminals in your plug proceed as follows: The wire

which is colored GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or

by the safety earth symbol or colored GREEN or GREEN-

and -YELLOW. The wire which is colored BLUE must be

connected to the terminal which is marked with the letter N

or colored BLACK. The wire which is colored BROWN

must be connected to the terminal which is marked with the

letter L or colored RED.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described above.

Note: The plug severed from the mains lead must be destroyed,

as a plug with a bared flexible cord is hazardous if engaged in a

live socket outlet.

For Canadian Customers

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES–003.

Caution: read this before operating this unit

100_Musiccast_E.p65 2003.06.28, 19:024

Caution: read this before operating this unit

5

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og

type. Levér det brugte batteri tilbage til leverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma

batterityp eller en ekvivalent typ som rekommenderas av

apparattillverkaren. Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

For US customers

This equipment complies with FCC radiation exposure limits

set forth for uncontrolled equipment. This equipment should

be installed and operated with a minimum distance of at least

20cm between the radiator and the persons body (excluding

extremities: hands, wrists, feet, and legs) and must not be co-

located or operated with any other antenna or transmitter.

For Canadian customers

Operation is subject to the following two conditions: (1) This

device may not cause interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation of the device.

The installer of this radio equipment must ensure that the

antenna is located or pointed such that it does not emit RF

field in excess of Health Canada limits for the general

population; consult Safety Code 6, obtainable from Health

Canada’s website www.hc-sc.gc.ca/rpb

For U.K. and European customers

We, the manufacturer YAMAHA hereby declare that the

MCX-A10 is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.

Vi, tillverkaren YAMAHA, betygar härmed att MCX-A10 är i

överensstämmelse med de erforderliga krav och andra

tillämpliga bestämmelser som anges i direktivet 1999/5/EC.

Noi, il fabbricante YAMAHA, con questo dichiariamo che

MCX-A10 si trova in osservanza dei requisiti essenziali e

delle altre normative pertinenti della direttiva 1999/5/EC.

Nosotros, el fabricante YAMAHA, declaramos por el presente

testamento que el MCX-A10 cumple con los requisitos

esenciales y otras provisiones pertinentes de la Directiva

1999/5/EC.

YAMAHA verklaart hierbij dat de MCX-A10 voldoet aan de

essentiële vereisten en andere relevante voorzieningen van

Richtlijn 1999/5/EC.

Allen voor klanten in

Nederland

Bij dit product zijn batterijen

geleverd.

Wanneer deze leeg zijn, moet u ze

niet weggooien maar inleveren als

KCA.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson

This product contains AVE-TCP from ACCESS CO.LTD.

100_Musiccast_E.p65 2003.06.28, 19:025

6

Contents

About your MusicCAST client

The MusicCAST client.................................... 8

Features..................................................... 8

Supplied accessories ..................................... 9

Controls and functions ................................. 10

Front panel............................................... 10

Side panel ................................................ 11

Remote control ........................................ 12

Modes of operation of the MusicCAST client

................................................................. 14

To turn the MusicCAST client on from

STANDBY mode .................................. 14

Using the Graphical User Interface of the

MusicCAST client .................................... 15

MusicCAST client Top Menu ............... 15

The lock icon ....................................... 15

The MusicCAST client controller ......... 15

Play Info screen ................................... 16

Setting up the MusicCAST client

Before setup ................................................. 17

Attaching the stand .................................. 17

Mounting the MusicCAST client on a wall

................................................................. 17

Removing the side-panel cover ............... 18

Remote control ........................................ 18

Loading the battery for the remote control

............................................................. 18

Battery replacement ............................ 18

Notes on the lithium battery ................. 18

Remote control operation range .......... 19

Connecting the AC adaptor...................... 19

Checking MusicCAST client connections

................................................................. 20

The MusicCAST network ............................. 21

Network addresses .............................. 22

Assigning IP addresses ....................... 22

Wireless network connections ................. 23

When and why should I use a wireless

connection? ......................................... 23

Wired network connections...................... 24

When should I use a wired connection?

............................................................. 24

What is a hub, and why do I need one?

............................................................. 24

Connecting to the network ........................... 25

Configuring your MusicCAST client ......... 25

Using the Auto Configuration function ..... 26

Configuring your MusicCAST client

manually .................................................. 28

Accessing the Manual Setup screen ... 29

Setting the Network Mode ................... 29

Setting the ESS ID............................... 30

Setting your MusicCAST client to act as a

DHCP client ......................................... 31

Setting the MusicCAST server Server ID

............................................................. 32

Setting the MusicCAST client IP Address

............................................................. 32

Setting the Subnet Mask Address ....... 33

Setting the WEP key for your MusicCAST

client .................................................... 33

Connection check ................................ 34

Playing back songs

Music playback on the MusicCAST client .... 35

Playback groups .................................. 35

During playback ................................... 36

To play a song from an artist.................... 37

To play a song from an album.................. 38

To play a song from a genre .................... 39

To select a song from the complete list of

songs ....................................................... 40

Using Playlists ......................................... 41

Accessing playlists with your MusicCAST

client .................................................... 41

Song Statistics ......................................... 42

To play a song in the list of bookmarks .... 43

Advanced playback options ......................... 45

Random Playback.................................... 45

To use the Random Playback function

............................................................. 45

To alter the limits of Random Playback

............................................................. 45

Repeat Playback...................................... 46

To use the Repeat Playback function .. 46

Changing the time display on the Play Info

screen ...................................................... 47

To alter the time display ....................... 47

Listening to an external source connected to

the MusicCAST server ............................. 48

To return to playback from the

MusicCAST server library .................... 49

Listening to a radio station with your

MusicCAST client .................................... 49

100_Musiccast_E.p65 2003.06.28, 19:026

Contents

7

Selecting a radio station ...................... 50

Listening to an external sound source ..... 51

To return to playback from the

MusicCAST server library .................... 51

Using the Bookmark function ....................... 52

Adding a song to the list of bookmarks .... 52

Adding a song using the Play Info screen

............................................................. 52

Adding a song using the menu ............ 52

Removing a song from the bookmark list

................................................................. 53

Removing a song using the Menu ....... 53

Copying the bookmark list to a playlist .... 54

Copying the bookmark list ................... 54

Erasing the bookmark list ........................ 55

Erasing the bookmark list .................... 55

Other functions

MusicCAST settings ..................................... 56

Default system settings ............................ 56

Using the OFF Timer function .................. 57

Using the menu to set the OFF Timer

function ................................................ 57

Using OFF TIMER on the remote control

to set the OFF Timer............................ 57

Using the ON Timer function .................... 58

Setting the timer .................................. 58

Using the ON TIMER key to activate the

ON Timer ............................................. 59

Using the Auto Play function .................... 59

Using the Auto Level Control function ...... 60

Turning Auto Level Control on or off .... 60

Using the tone controls ............................ 61

Altering the tone settings ..................... 61

Using the contrast controls ...................... 62

Altering the contrast settings ............... 62

Using the Sleep function .......................... 63

Switching the unit to sleep mode ......... 63

Turning the MusicCAST client on again

............................................................. 63

System settings ............................................ 64

Displaying System Information on the

MusicCAST client .................................... 64

Accessing the System Information screen

............................................................. 64

Updating the MusicCAST client firmware

................................................................. 65

Resetting the MusicCAST client to default

settings .................................................... 66

Resetting your MusicCAST client ........ 66

Displaying Network Status Information on

the MusicCAST client .............................. 67

Accessing the Network Status screen

............................................................. 67

Appendix

Troubleshooting ........................................... 69

Terms used in this manual ........................... 72

Specifications ............................................... 74

Index ............................................................ 75

100_Musiccast_E.p65 2003.07.14, 11:287

8

The MusicCAST client

The MusicCAST client is designed to work in conjunction with the Yamaha MusicCAST server to allow

you to store and listen to your entire music collection. With multiple clients, you and others can

simultaneously access and listen to your music collection from up to seven different locations.

Features

◆ Wireless networking with the MusicCAST server

◆ Instant access to all music data stored on the MusicCAST server

◆ Simultaneous playback from multiple locations (for multiple clients)

◆ 128 x 64 dot LCD display and remote control for easy operation

◆ Internal Yamaha digital amplifier

◆ 2 x 17 W/4 Ω outputs

◆ Slim Desktop/Wall mountable design

This owner’s manual refers to the MCX-1000 DIGITAL AUDIO SERVER as the MusicCAST

server and the MCX-A10 DIGITAL AUDIO TERMINAL as the MusicCAST client.

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the

most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear

without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged

exposure from excessive volume levels.

We Want You Listening For A Lifetime

101_Musiccast_E.p65 2003.06.28, 19:028

About your MusicCAST client

9

Remote control

Stand

Screw x 2

Supplied accessories

After unpacking, check that the following parts are included.

Lithium battery

Audio pin cable

Subwoofer cable

Video pin cable

AC adaptor (LSE0107A1240)

AC power cable

OFF TIMER

ON TIMER

I23

REPEAT RANDOM

SLEEP

456

PAUSE

7

STOP

S

PLAY

MENU

SELECT

VOL

GROUP GROUP

INPUT

MUTERECALL

BOOK

MARK

PLAY

INFO.

101_Musiccast_E.p65 2003.06.28, 19:029

10

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

1

2

q

0

w

8

7

9

3

5

6

4

DIGITAL AUDIO TERMINAL MCX–A10

Controls and functions

1 POWER indicator

Lights when the MusicCAST client is active.

2 TIMER indicator

Lights when the timer function is activated (see

pages 57 – 59).

3 Front panel display

Displays information on the settings and songs

available in your MusicCAST network.

4 MENU

Returns the on-screen display to the menu page.

5 PLAY INFO.

Displays information on the song you are currently

listening to on the front panel display.

6 VOL +/–

Adjust the volume of the MusicCAST client output.

7 STANDBY/ON

Switches the MusicCAST client between ON and

STANDBY modes.

8 s

Halts playback from the MusicCAST client.

9 p

Begins playback of the selected track.

0 Controller

Moves the on-screen cursor within the Graphical

User Interface, and enters, deletes, or selects the

selection highlighted on the front panel display.

q Remote control signal receiver

Receives signals from the MusicCAST client

remote control.

w PHONES jack

Insert your headphones plug here to listen to the

MusicCAST client through headphones. Output

from the S.WOOFER jack and SPEAKER OUT

terminals stops.

Front panel

101_Musiccast_E.p65 2003.06.28, 19:0210

About your MusicCAST client

Controls and functions

11

Side panel

1 LAN port

Insert a LAN cable here to connect to a wired

network.

2 AUX IN jack

Connect an external sound source here.

3 LINEOUT L/R jacks

Use these jacks to connect the MusicCAST client to

an input on an external component.

4 S. WOOFER jack

Use this jack to connect the MusicCAST client to a

subwoofer to achieve a more powerful, better

defined bass sound.

5 VIDEO OUT jack

Use this jack to connect the MusicCAST client to

an external view device, such as a monitor or

television. You can view the front panel display on

this device.

6 SPEAKER OUT terminals

Connect speaker cables to these terminals.

7 AC adaptor input

Connect the AC adaptor to this input.

–

LA

N

A

U

X

IN

LIN

E

O

U

T

S

.W

O

FER

L

S

PE

A

K

E

R

O

U

T

4

Ω

M

IN

.

C

LA

S

2

W

IRIN

G

D

C

IN

1

2

V

G

N

D

R

L

R

V

ID

EO

O

U

T

+–+

1

2

6

7

3

5

4

101_Musiccast_E.p65 2003.06.28, 19:0211

Controls and functions

12

Remote control

OFF TIMER

ON TIMER

I23

REPEAT RANDOM

SLEEP

456

PAUSE

7

STOP

S

PLAY

MENU

SELECT

VOL

GROUP GROUP

INPUT

MUTERECALL

BOOK

MARK

PLAY

INFO.

1

2

u

i

o

a

s

d

h

j

g

f

p

3

5

8

0

e

t

y

q

w

r

9

6

7

4

1 Infrared emitter

Emits infrared control signals for the MusicCAST

client to receive. Aim the emitter at the

MusicCAST client when you want to operate it.

2 OFF TIMER

Activates the off timer function (see page 57) and

cycles through the available timer settings.

3 ON TIMER

Switches the ON TIMER function (see pages 58,

59) on and off.

4 REPEAT

Places the unit in repeat playback mode (see pages

46, 47).

5 b

Accesses the previous track in the group you are

listening to.

6 w

Searches back through the current song.

7 s (STOP)

Halts playback from the MusicCAST client.

8 MENU

Returns the on-screen display to the menu page.

9 p (PLAY)

Begins playback of the selected track.

0 GROUP –

Accesses the previous playback group.

q j

Moves the on-screen cursor to the left, and accesses

the previous menu page.

w SELECT

Enters, deletes, plays, or selects the selection

highlighted on the front panel display.

This section explains the function of each button on

the remote control.

101_Musiccast_E.p65 2003.06.28, 19:0212

About your MusicCAST client

Controls and functions

13

e BOOKMARK

Attaches or removes a bookmark from a song (see

pages 52 – 55).

r d

Moves the on-screen cursor down.

t RECALL

This button and the corresponding Recall Play

menu in the MusicCAST client are reserved for

future functionality.

y VOL +/–

Adjust the volume of the MusicCAST client output.

u SLEEP

Switches the MusicCAST client between sleep and

on modes.

i RANDOM

Places the unit in random playback mode (see

pages 45, 46).

o a

Accesses the next song in the group you are

listening to.

p e (PAUSE)

Pauses playback of the track you are currently

listening to.

a f

Searches forwards through the current song.

s PLAY INFO.

Displays information on the song you are currently

listening to on the front panel display.

d GROUP +

Accesses the next playback group.

f u

Moves the on-screen cursor up.

g i

Enters into menu items highlighted on the front

panel display, and moves the on-screen cursor to

the right.

h INPUT

Switches the input to the amplifier in the

MusicCAST client between the signal from the

MusicCAST server and signals received from the

AUX IN jack.

j MUTE

Mutes the output from the unit.

101_Musiccast_E.p65 2003.06.28, 19:0213

Controls and functions

14

Modes of operation of the MusicCAST client

The MusicCAST client has three modes of operation.

• STANDBY: The MusicCAST client is connected to an AC outlet with STANDBY/ON on its top

surface in the STANDBY position (fully up).

• SLEEP: The MusicCAST client is connected to an AC outlet with STANDBY/ON on its top

surface in the ON position (fully down), the POWER indicator on its front panel lit, and

the time displaying on its front panel display.

• ON: The MusicCAST client is connected to an AC outlet with STANDBY/ON on its top

surface in the ON position (fully down), the POWER indicator on its front panel lit, and

information other than the time displaying on its front panel display.

■ To turn the MusicCAST client on from

STANDBY mode

1. Press STANDBY/ON.

The MusicCAST client turns on, displaying its

startup screen, then displays the Top Menu

screen.

2. The MusicCAST client attempts to

connect to the MusicCAST server,

displaying the following screen:

Top

Menu

Play

Recall

Play

Edit

Bookmark

Setup

Input

Top

Menu

Play

Connecting...

Input

3. If it is able to make a connection, the

MusicCAST client returns to the Top

Menu screen, displaying the network

connection icon in the top right corner

of the screen.

If it is not able to make a connecting, the

MusicCAST client continues displaying

the “Connecting...” message. Press any

of the controls on the MusicCAST client

to erase this message, and check the

MusicCAST client network connection

settings.

Note

• If you do not use the MusicCAST client for 30

minutes, it automatically places itself in sleep

mode. Press SELECT or SLEEP to reactivate it.

101_Musiccast_E.p65 2003.06.28, 19:0214

About your MusicCAST client

Controls and functions

15

■ MusicCAST client Top Menu

1 Menu name

2 Cursor

3 Connection icon

4 Lock icon

5 Menu

This is a typical screen from the GUI of the

MusicCAST client. All of the features indicated

here are displayed on almost all of the screens you

encounter when using the MusicCAST client. Use

the cursor keys on the remote to move the cursor to

the desired position, and SELECT to perform an

action.

■ The lock icon

The MusicCAST server can lock MusicCAST

clients so that you can only control the volume and

mute functions, or stop playback. When locked, the

MusicCAST client displays the lock icon in the

dark bar at the top of the on-screen display. You can

reset the lock by unlocking the MusicCAST client

from the MusicCAST server. Refer to the MCX-

1000 owner’s manual for more information on

locking clients.

Using the Graphical User Interface of the MusicCAST client

The MusicCAST client offers a wide variety of functions and parameters for your use. You can access all of

these through the Graphical User Interface (GUI) viewable from the front panel display on the MusicCAST

client itself. The interface, as laid out below, is simple and easy to understand.

■ The MusicCAST client controller

Moving the controller in the directions indicated on

the front panel of the MusicCAST client performs

the same actions as pressing the equivalent cursor

key on the remote control. For example, pushing

the MusicCAST client controller upwards produces

the same result as pressing u on the remote

control. Pushing the controller directly into the

front panel has the same effect as pressing SELECT

on the remote control.

This manual explains how to use the various

functions of the MusicCAST client using the

remote control only. While many functions are

accessible from the main panel of the MusicCAST

client, some functions are only accessible from the

remote control.

Top

Menu

Play

Recall

Play

Edit

Bookmark

Setup

Input

1

2

3

5

4

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

Controller

101_Musiccast_E.p65 2003.06.28, 19:0215

Controls and functions

16

■ Play Info screen

Press PLAY INFO to display this screen on the on-

screen display of the MusicCAST client.

1 Artist name

2 Album name

3 Song name

4 Time counter

5 Current action mode icon

Indicates the current action being taken by the

MusicCAST.

s: Playback is stopped

p: Playing a song

e: Playback is paused

6 Repeat icon

Indicates whether or not the MusicCAST client is

in repeat play mode.

7 Random play icon

8 Group skip target

Indicates the group within which the group skip

function is currently operating.

9 Mute icon

Play Info

Artist name

Album name

Song name

Album

Play Info

Artist name

Album name

Song name

Album

9

7

8

654

1

2

3

The Play Info screen displays information on the

song the MusicCAST is currently playing, or the

last song played if it is not currently playing a song.

Note

• MusicCAST clients can use the VIDEO OUT jack

on the MusicCAST client to display the on-screen

display on a TV/monitor.

101_Musiccast_E.p65 2003.06.28, 19:0216

Setting up the MusicCAST client

17

Attaching the stand

1.

Place the MusicCAST client so that its

front panel display faces down, taking

care not to scratch the front panel in the

process.

2. Place the stand so that the two pins on

the lower bar of the stand fit into the

holes on the lower surface of the

MusicCAST client.

3. Using a screwdriver, attach the top bar

of the stand to the MusicCAST with the

provided screws.

Before setup

Mounting the MusicCAST client on a wall

1. Insert 2 self-tapping screws (diameter:

3.5 to 4 mm) into the wall, 40 mm apart.

2. Mount the MusicCAST client on the

screws by positioning it so that the

screws on the wall fit snugly into the

holes on the mounting bracket.

Cautions

• The MusicCAST client weighs 2 kg (4 lbs 6 oz).

Do not mount it on thin plywood or a wall with

soft surface material. If mounted, the screws may

come loose from the flimsy surface and the

speaker may fall. This damages the MusicCAST

client and may cause personal injury.

• Do not use nails, adhesives, or other unstable

materials to mount the MusicCAST client. Long-

term use and vibrations may cause it to fall.

• To avoid accidents resulting from tripping over

loose cables, fix it to the wall.

40mm

4mm 20mm or more

102_Musiccast_E.p65 2003.06.28, 19:0217

Before setup

18

Removing the side-panel cover

1.

Push the tab down firmly.

2. Slide the cover away from the

MusicCAST client casing.

Remote control

■ Loading the battery for the remote

control

1. Slide out the battery holder from the

remote control by pushing into the hole

in the holder with a ball-point pen, etc.

Note

• The casing is very stiff, and may require

significant pressure to remove.

2. Place the battery in the holder, positive

side upward.

3. Slide the holder into the remote control.

■ Battery replacement

If you find that the remote control must be used

closer to the main unit than usual, the battery is

weak. Replace the battery with new one.

■ Notes on the lithium battery

Please take care when using the lithium battery as it

may explode if mistreated.

• Never abuse or disassemble the battery.

• Be sure the battery polarity is correct. If it is not

installed correctly, it may cause fire or explosion.

• Avoid placing the lithium battery and also the

remote control with the battery installed, in high

temperature such as direct sunlight.

• Do not recharge the battery.

• When replacing the battery, make sure to only use

a CR2025 battery.

• Keep the battery out of reach of children. If

swallowed, get immediate medical help.

• When disposing of the battery, insulate it with

tape, etc. Never dispose of it in fire. Also, dispose

of the battery according to local regulations.

• If the battery leaks, dispose of it immediately.

Avoid touching the leaked material or letting it

come in contact with clothing, etc. Skin contact

may cause a burn. If it occurs, wash the affected

area with water promptly and get medical

attention.

102_Musiccast_E.p65 2003.06.28, 19:0218

Setting up the MusicCAST client

Before setup

19

Connecting the AC adaptor

1.

Insert the AC power cable into the AC

adaptor.

2. Connect the AC adaptor to the AC

adaptor input on the MusicCAST client.

3. Plug in the AC power cable to an AC

outlet.

■ Remote control operation range

Cautions

• If operation of this unit by the remote control

creates any malfunction in any other components,

change the placement of the component.

• Do not spill any liquid on or drop the remote

control. Do not place it near a heater or in the

bathroom where the temperature and humidity

become high.

• Make sure the remote control signal receiver is

not exposed to direct sunlight or strong lights.

Such exposure may inhibit the functioning of the

remote control.

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

OFF TIMER

ON TIMER

I23

REPEAT RANDOM

SLEEP

456

PAUSE

7

STOP

S

PLAY

MENU

SELECT

VOL

GROUP GROUP

INPUT

MUTERECALL

BOOK

MARK

PLAY

INFO.

DIGITAL AUDIO TERMINAL MCX–A10

30° 30°

Within 6m (20’)

Remote control

signal receiver

–

L

A

N

A

U

X

I

N

L

IN

E

O

U

T

S

.

W

O

F

E

R

L

S

P

E

A

K

E

R

O

U

T

4

Ω

M

IN

.

C

L

A

S

2

W

IR

I

N

G

D

C

IN

1

2

V

G

N

D

R

L

R

V

ID

E

O

U

T

+–+

LINEOUT

S.WOOFER

L

SPEAKER OUT

4Ω MIN.

DC IN 12V

GND

R

VIDEO OUT

This picture depicts the style of

AC outlet found in the United

States of America.

102_Musiccast_E.p65 2003.06.28, 19:0219

Before setup

20

Checking MusicCAST client connections

Before you attempt to use the MusicCAST client to play music, check the following:

1 If you wish to listen to music with the MusicCAST client without using headphones, have you

connected it to an external receiver, or to speakers?

2 If you intend to connect to your MusicCAST server using the built in wireless network connection, have

you placed the MusicCAST client within an appropriate distance of the server? (see page 23)

3 If you intend to connect to your MusicCAST server using a wired network connection, have you

connected your MusicCAST client to the server with a LAN cable to a hub?

4 Is the MusicCAST server power turned on?

5 Is the MusicCAST client connected to an AC outlet?

6 Is the MusicCAST client power turned on?

–

LAN

AUX IN

LINEOUT

S.W

OOFER

L

SPEAKER OUT

4Ω

M

IN.

CLASS 2

W

IRING

DC IN 12V

GND

R

L

R

VID

EO OUT

+–+

DIGITAL AUDIO SERVER MCX-1000

STANDBY/ON

TOP MENU

MENU

PLAY INFO.

TIMER

CLIENT STATUS

LAN

STANDBY

ENCODING

BACK

CD AUTO STORE

SUB MENU PAGE

PUSH

SELECT

12345

5

1

3

1

4

6

2

102_Musiccast_E.p65 2003.06.28, 19:0220

Setting up the MusicCAST client

21

The MusicCAST server stores all music data used in your MusicCAST system. The MusicCAST client does

not store or record any music data. Your MusicCAST client uses a Local Area Network (LAN) to transmit

and receive data from the MusicCAST server, which it then plays back as music.

The MusicCAST system can use both wired and wireless network connections to transmit music data. Both

types of connections transmit the same data.

The wireless network in your MusicCAST system uses high frequency radio signals to transmit data.

You do not need a physical connection between your MusicCAST server and clients to listen to music over

a wireless network, but you need to place all clients in fairly close proximity to the server for them to work

properly:

A wired network transmits data through a special type of cable, called a LAN cable. You must physically

connect each MusicCAST client and server to a network router or hub with one of these cables.

Connections using LAN cables functions without problems over much longer distances than connections

using the wireless network used in the MusicCAST system.

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

DIGITAL AUDIO SERVER MCX-1000

STANDBY/ON

TOP MENU

MENU

PLAY INFO.

TIMER

CLIENT STATUS

LAN

STANDBY

ENCODING

BACK

CD AUTO STORE

SUB MENU PAGE

PUSH

SELECT

12345

DIGITAL AUDIO TERMINAL MCX–A10 DIGITAL AUDIO TERMINAL MCX–A10

DIGITAL AUDIO TERMINAL MCX–A10DIGITAL AUDIO TERMINAL MCX–A10

DIGITAL AUDIO TERMINAL MCX–A10

DIGITAL AUDIO SERVER MCX-1000

STANDBY/ON

TOP MENU

MENU

PLAY INFO.

TIMER

CLIENT STATUS

LAN

STANDBY

ENCODING

BACK

CD AUTO STORE

SUB MENU PAGE

PUSH

SELECT

12345

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

ON

TIMER

PUSH

SELECT

MENU

PLAY INFO.

–

VOL

+

PHONES

DIGITAL AUDIO TERMINAL MCX–A10

The MusicCAST network

Network hub or

switching hub

102_Musiccast_E.p65 2003.06.28, 19:0221

Sayfa yükleniyor ...

Yamaha MCX-A10 El kitabı

Yamaha MCX-A10 El kitabı

Diğer dillerde

İlgili Makaleler