Yamaha RX-V757 El kitabı

RX-V757 AV Receiver

DSP-AX757SE AV Amplifier

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

GB

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this sound system in a well ventilated, cool,

dry, clean place – away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

Allow ventilation space of at least 30 cm on the top,

20 cm on the left and right, and 20 cm on the back of

this unit.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in a environment with high humidity (i.e. a room with

a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord and outdoor antenna from the wall outlet

during an electrical storm.

14 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WAR NING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if this unit itself is turned off. This state is called the

standby mode. In this state, this unit is designed to

consume a very small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel................................................................. 4

Remote control........................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

Rear panel ................................................................ 10

SPEAKER SETUP ............................................... 11

Speaker placement................................................... 11

Speaker connections ................................................ 12

CONNECTIONS .................................................. 15

Before connecting components................................ 15

Connecting video components................................. 16

Connecting audio components................................. 19

Connecting the FM and AM antennas

(RX-V757 only) .................................................. 21

Connecting the power supply cord .......................... 22

Speaker impedance setting ...................................... 23

Turning on the power............................................... 23

AUTO SETUP....................................................... 24

Introduction.............................................................. 24

Optimizer microphone setup.................................... 24

Starting the setup ..................................................... 25

PLAYBACK.......................................................... 30

Basic operations....................................................... 30

Selecting sound field programs ............................... 32

Selecting input modes.............................................. 37

FM/AM TUNING (RX-V757 ONLY)................. 39

Automatic and manual tuning.................................. 39

Presetting stations.................................................... 40

Selecting preset stations........................................... 42

Exchanging preset stations ...................................... 43

Receiving Radio Data System stations.................... 44

Changing the Radio Data System mode ..................45

PTY SEEK function ................................................ 46

EON function........................................................... 47

RECORDING ....................................................... 48

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................49

For movie/video sources.......................................... 49

For music sources .................................................... 51

ADVANCED OPERATIONS ..............................52

Selecting the OSD mode.......................................... 52

Using the sleep timer ............................................... 52

Manually adjusting speaker levels........................... 53

SET MENU............................................................54

Using SET MENU................................................... 56

1 SOUND MENU.................................................... 57

2 INPUT MENU...................................................... 62

3 OPTION MENU................................................... 64

ADVANCED SETUP MENU...............................66

REMOTE CONTROL FEATURES ...................68

Control area ............................................................. 68

Setting remote control codes ................................... 69

Controlling other components ................................. 71

Programming codes from other remote controls .....72

Changing source names in the display window....... 73

Clearing function sets .............................................. 74

Clearing individual functions .................................. 75

ZONE 2 (RX-V757 ONLY) ..................................76

Zone 2 connections.................................................. 76

Remote controlling Zone 2 ...................................... 77

EDITING SOUND FIELD PARAMETERS ......79

What is a sound field ............................................... 79

Changing parameter settings ................................... 79

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................81

TROUBLESHOOTING .......................................86

RESETTING THE FACTORY PRESETS ........91

GLOSSARY...........................................................92

Audio formats .......................................................... 92

Sound field programs............................................... 93

Audio information ................................................... 93

Video signal information ......................................... 94

SPECIFICATIONS...............................................95

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

FEATURES

2

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz to 20 kHz, 8 !)

Front: 100 W + 100 W

Center: 100 W

Surround: 100 W + 100 W

Surround back: 100 W + 100 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of

sound fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/

Dolby Pro Logic IIx decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner (RX-V757 only)

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Other features

◆ YPAO: YAMAHA Parametric Room Acoustic

Optimizer for automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ A SET MENU that provides you with items for

optimizing this unit for your audio/video system

◆ 8 additional input jacks for discrete multi-channel input

◆ PURE DIRECT for pure fidelity sound with analog and

PCM sources

◆ On-screen display function helpful in controlling this

unit

◆ S-video signal input/output capability

◆ Component video input/output capability

◆ Video signal conversion (Composite video " S-video

# Component video) capability for monitor out

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes and

“learning” capability

◆ Zone 2 custom installation facility (RX-V757 only)

• This document is the owner’s manual for both RX-V757 and DSP-AX757SE. Model names are given where the details of functions

are unique to each model. Illustrations for RX-V757 are mainly used for explanations.

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol

are trademarks of Dolby Laboratories.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of

Digital Theater Systems, Inc.

FEATURES

GETTING STARTED

3

INTRODUCTION

English

Please check that you received all of the following parts.

1 Press the part and slide the battery

compartment cover off.

2

Insert four supplied batteries (AAA, R03,

UM-4) according to the polarity markings

(+ / –) on the inside of the battery

compartment.

3 Slide the cover back until it snaps into place.

Notes on batteries

• Change all of the batteries if you notice the following

conditions; the operation range of the remote control decreases,

the indicator does not flash or its light becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

GETTING STARTED

Supplied accessories

TRANSMIT

RE-NAME

INPUT MODE

STANDBY

SYSTEM

POWER

AB

PHONO

CDMD/CD-RTUNERV-AUX

DVD

AMP

POWERPOWER

REC

AUDIO

MUTE

MENUTITLE

CH CH

VOL

DISC SKIP

SET MENU

LEVEL

PRESET

SRCH MODE

A/B/C/D/E

BAND

TV INPUT

TV VOL

ON SCREEN

STRAIGHT

MOVIEENTERTAINMUSICSTEREO

4321

8

10

7

09

65

ENT.

PURE DIRECT

EXTD SUR.STANDARD SELECT

NIGHT

SPEAKERSAB

EFFECTMEMORY

CHP/INDEX

DISPLAYRETURN

TV MUTE

ENTER

TV VOL

AVTV

SELECT

VCR 1DTV/CBL DVR/VCR2

MULTI CH IN

SLEEP

CLEAR LEARN

PRESET

FREQ/TEXT

EON

STARTMODE

PTY SEEK

Remote control

Batteries (4)

(AAA, R03, UM-4)

AM loop antenna

(RX-V757 only)

Indoor FM antenna

(RX-V757 only)

Optimizer microphone

Installing batteries in the remote

control

1

3

2

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the remote control code and program

any acquired functions that may have been cleared.

CONTROLS AND FUNCTIONS

4

1 STANDBY/ON

Turns on this unit or sets it to the standby mode. When you

turn on this unit, you will hear a click and there will be a 4

to 5-second delay before this unit can reproduce sound.

In standby mode, this unit consumes a small amount of power in

order to receive infrared-signals from the remote control.

2 OPTIMIZER MIC jack

Use to connect and input audio signals from the supplied

microphone for use with the AUTO SETUP function (see

page 24).

3 Remote control sensor

Receives signals from the remote control.

4 Front panel display

Shows information about the operational status of this

unit.

5 A/B/C/D/E

(RX-V757 only)

Selects one of the 5 preset station groups (A to E) when

the unit is in tuner mode.

6 PRESET/TUNING l / h

(RX-V757 only)

Selects preset station number 1 to 8 when the colon (:) is

displayed next to the band indication in the front panel

display when the unit is in tuner mode. Selects the tuning

frequency when the colon (:) is not displayed.

LEVEL –/+

Adjusts the level of the speaker channel selected using

NEXT.

7 MEMORY (MAN’L/AUTO FM)

(RX-V757 only)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

8 TUNING MODE (AUTO/MAN’L MONO)

(RX-V757 only)

Switches the tuning mode between automatic (AUTO

indicator on) and manual (AUTO indicator off).

9 VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

0 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

CONTROLS AND FUNCTIONS

Front panel

MAIN

ZONE ON/OFF

ZONE 2

DISPLAY

S VIDEO VIDEO OPTICALL AUDIO R

CATEGORY

SEARCH MODE

EFFECT

XIM

OPTIMIZER MIC

PROGRAM

PURE DIRECTINPUT MODETONE CONTROLSTRAIGHT

SPEAKERSPHONES

SILENT CINEMA

STANDBY

/ON

BA

MULTI CH

INPUT

VOLUME

VIDEO AUX

INPUT

LEVEL

PRESET/TUNING A/B/C/D/E

l PRESET/TUNING h

TUNING MODE

MAN'L/AUTO FM AUTO/MAN'L MONO

EDIT

30 30

TRANSMIT

RE–NAME

CLEAR

LEARN

POWER SLEEP

STANDBY

INPUT MODE

SYSTEM

PHONO TUNER CD

MULTI CH IN

V

-

AUX

CBL/SATMD/TAPE CD-R

DTV DVR/VCR2VCR 1 DVD

SELECT

POWER

TV

POWER

AV

AMP

REC

DISC SKIP

AUDIO

VOL

LEVEL

TITLE

BAND

TV INPUT

SRCH MODE

TV VOL

SET MENU

MENU

A/B/C/D/E

MUTE

CH

TV MUTE

ENTER

CH

PRESET PRESET

RETURN

TV VOL

ON SCREEN

DISPLAY

STRAIGHT

EFFECTMEMO

STEREO

MUSIC

ENTERTAINMOVIE

12

34

56

8

STANDARD

SELECT

EXTD SUR.

PURE DIRECT

7

90

ENT.

+10

NIGHT

A

SPEAKERS

B

CHP/INDEX

PRESET

FREQ/TEXT

EON

STARTMODE

PTY SEEK

Approximately 6 m

CONTROLS AND FUNCTIONS

8

1 Decoder indicators

When any of this unit’s decoders function, the respective

indicator lights up.

2 VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 36).

3 SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 31).

4 Input source indicators

A cursor lights to show the current input source.

5 Sound field indicators

Light to indicate the active DSP sound fields.

6 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program.

7 YPAO indicator

Lights up during the auto setup procedure and when the

auto setup speaker settings are used without any

modifications.

8 AUTO indicator

(RX-V757 only)

Lights up when this unit is in automatic tuning mode.

9 TUNED indicator

(RX-V757 only)

Lights up when this unit is tuned into a station.

0 STEREO indicator

(RX-V757 only)

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the AUTO indicator is lit.

A MEMORY indicator

(RX-V757 only)

Flashes to show that a station can be stored.

B MUTE indicator

Flashes while the MUTE function is on.

C VOLUME level indication

Indicates the current volume level.

D PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

E STANDARD indicator

Lights up when a decoder is selected (see page 34).

F NIGHT indicator

Lights up when you select night listening mode.

G SP A B indicators

Light up according to the set of front speakers selected.

Both indicators light up when both sets of speakers are

selected.

H Headphones indicator

Lights up when headphones are connected.

I HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program.

J Multi-information display

Shows the current sound field program name and other

information when adjusting or changing settings.

Front panel display

PHONOCDTUNER

MD/CD-R

DVD

DTV/CBL

V-A UX

VCR1

DVR/VCR2

96

24

q

PL

q

EX

q

PL

MATRIX DISCRETE

SILENT CINEMA

NIGHT

ZONE2STANDARD

AUTO

YPAO

PS

HOLD

RT CT EONPTYPTY

TUNED STEREO MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

q

PL x

A B

SP

mS

dB

ft

dB

96/24

HiFi DSP

LFE

LCR

SL SB SR

q

DIGITAL

t

12345678*9* A* BC0*

O*

IJ M

KNLED

FH

G

P*

* RX-V757 only

Presence DSP sound field

Listening position

Left surround

DSP sound field

Right surround

DSP sound field

Surround back DSP sound field

CONTROLS AND FUNCTIONS

9

INTRODUCTION

English

K SLEEP indicator

Lights up while the sleep timer is on.

L 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

M LFE indicator

Lights up when the input signal contains the LFE signal.

N Input channel indicators

Indicate the channel components of the current digital

input signal.

O ZONE 2 indicator

(RX-V757 only)

Lights up when Zone 2 power is on.

P Radio Data System indicators

(RX-V757 only)

The name(s) of the Radio Data System data offered by the

currently received Radio Data System station light(s) up.

EON lights up when an Radio Data System station that

offers the EON data service is being received.

PTY HOLD lights up while searching for stations in the

PTY SEEK mode.

CONTROLS AND FUNCTIONS

10

1 DIGITAL OUTPUT jacks

See page 19 for details.

2 Audio component jacks

See page 19 for connection information.

3 Video component jacks

See pages 16 and 18 for connection information.

4 Antenna terminals

(RX-V757 only)

See page 21 for connection information.

5 PRESENCE/ZONE 2 speaker terminals

(RX-V757 only)

PRESENCE speaker terminals

(DSP-AX757SE only)

See page 13 for connection information.

6 REMOTE IN/OUT jacks

(RX-V757 only)

See page 76 for details.

7 CONTROL OUT jack

(RX-V757 only)

This is a control expansion terminal for commercial use.

8 AC OUTLET(S)

Use to supply power to your other A/V components (see

page 22).

9 DIGITAL INPUT jacks

See pages 16, 18 and 19 for details.

0 MULTI CH INPUT jacks

See page 17 for connection information.

A ZONE 2 OUTPUT jacks

(RX-V757 only)

These jacks output analog signals only. See page 76 for

details.

TUNER INPUT jacks

(DSP-AX757SE only)

These jacks input signals from the external tuner.

B PRE OUT jacks

See page 20 for connection information.

C Speaker terminals

See page 12 for connection information.

Rear panel

GND

AUDIO AUDIO

DIGITAL

INPUT

DVD

CD

COAXIAL

DTV/CBL

MD/CD-R

SUB

WOOFER

SURROUND

BACK

SURROUND

FRONT

OUT

(REC)

IN

(PLAY)

MD

/CD-R

CD

PHONO

DVD

VIDEO

MONITOR

OUT

DTV

/CBL

DVD

COMPONENT VIDEO

PR PB Y

75Ω UNBAL.

FM

ANT

AM

ANTGND

TUNER

DTV/

CBL

IN

VCR 1

OUT

IN

DVR/

VCR 2

OUT

CENTER

DIGITAL

OUTPUT

MULTI CH INPUT

ZONE 2

OUTPUT

VIDEO S VIDEO

MONITOR OUT

FRONT

SUB

WOOFER

FRONT

A

B

CENTER SINGLE

PRE OUT

SURROUND

BACK

PRESENCE/

ZONE 2

OUT

IN

REMOTE

CONTROL

OUT

AC OUTLETS

SWITCHED

+12V

15mA MAX.

SPEAKERS

SURROUND

CENTER

SURROUND BACK

OPTICAL

12 3 4* 7* 86*5*

90 A* BC

XM

* RX-V757 only (or DSP-AX757SE has different jacks)

SPEAKER SETUP

11

PREPARATION

English

The speaker layout below shows the standard ITU-R

*

speaker setting. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

*

ITU-R is the radio communication sector of the ITU

(International Telecommunication Union).

Front speakers (FR and FL)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Align the front

face of the center speaker with the front face of your video

monitor. Place the speaker centrally between the front

speakers and as close to the monitor as possible, such as

directly over or under it.

Surround speakers (SR and SL)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back speakers (SBR and SBL)

The surround back speakers supplement the surround

speakers and provide for more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm apart.

Ideally, they should be positioned at the same width as the

front speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active

Servo Processing Subwoofer System, is effective not only

for reinforcing bass frequencies from any or all channels,

but also for high fidelity reproduction of the LFE (low-

frequency effect) channel included in Dolby Digital and

DTS software. The position of the subwoofer is not so

critical, because low bass sounds are not highly

directional. But it is better to place the subwoofer near the

front speakers. Turn it slightly toward the center of the

room to reduce wall reflections.

Presence speakers (PR and PL)

Presence speakers supplement the sound from the front

speakers with extra ambient effects produced by CINEMA

DSP (see page 49). These effects include sounds that

filmmakers intend to locate a little farther back behind the

screen in order to create more theater-like ambience. Place

these speakers at the front of the room about 0.5 – 1 m

outside the front speakers, facing slightly inwards, and

about 1.8 m above the floor.

SPEAKER SETUP

Speaker placement

60˚

30˚

PL

PR

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

30 cm or more

1.8 m

12

SPEAKER SETUP

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

• If you will use 4 or 6 ohm speakers, be sure to

set this unit’s speaker impedance setting to 4

ohms before using (see page 23).

• Before connecting the speakers, make sure that the

power of this unit is off.

• Do not let the bare speaker wires touch each other or do

not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals on this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

1 Remove approximately 10 mm of insulation

from the end of each speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

■ Connecting to PRESENCE/ZONE 2 or

PRESENCE speaker terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

Speaker connections

CAUTION

10 mm

1

2

Red: positive (+)

Black: negative (–)

3

4

5

2

1

3

13

SPEAKER SETUP

PREPARATION

English

FRONT

SUB

WOOFER

FRONT

A

B

CENTER SINGLE

PRE OUT

SURROUND

BACK

PRESENCE/

ZONE 2

SPEAKERS

SURROUND

CENTER

SURROUND BACK

231

6 7 10

98

4 5

Subwoofer

system

Center

speaker

Front speakers (A)

Surround back

speakers

LeftRight

Surround speakers

Front

speakers

(B)

LeftRight

Presence speakers

You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.

• The surround back speakers output the surround back channel included in Dolby Digital EX and DTS-ES software and only

operate when the Dolby Digital EX, DTS-ES or Dolby Pro Logic IIx decoder is turned on.

• The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields

are selected.

14

SPEAKER SETUP

■ FRONT terminals

Connect one or two speaker systems (6, 7) to these

terminals. If you use only one speaker system, connect it

to the FRONT A or B terminals.

■ CENTER terminals

Connect a center speaker (8) to these terminals.

■ SURROUND terminals

Connect surround speakers (4, 5) to these terminals.

■ SUBWOOFER jack

Connect a subwoofer with built-in amplifier (1), such as

the YAMAHA Active Servo Processing Subwoofer

System, to this jack.

■ SURROUND BACK terminals

Connect surround back speakers (9, 10) to these terminals.

If you only connect one surround back speaker, connect it

to the left (L) terminals.

■ PRESENCE terminals

Connect presence speakers (2, 3) to these terminals.

*

If you are using RX-V757, you can also use these speakers as

Zone 2 speakers (see page 65).

1

6

7

8

9

2

3

5

4

10

Speaker layout

CONNECTIONS

15

PREPARATION

English

Do not connect this unit or other components to the mains

power until all connections between components are

complete.

■ Cable indications

■ Analog jacks

You can input analog signals from audio components by

connecting audio pin cable to the analog jacks on this unit.

Connect red plugs to the right jacks and white plugs to the

left jacks.

■ Digital jacks

This unit has digital jacks for direct transmission of digital

signals through either coaxial or fiber optic cables. You

can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both

the COAXIAL and OPTICAL jacks, priority is given to

the input signals from the COAXIAL jack. All digital

input jacks are compatible with 96-kHz sampling digital

signals.

This unit handles digital and analog signals independently. Thus

audio signals input to the analog jacks are only output to the

analog OUT (REC) jacks. Likewise audio signals input to the

digital (OPTICAL or COAXIAL) jacks are only output to the

DIGITAL OUTPUT jack.

Dust protection cap

Pull out the cap from the optical jack before you connect

the fiber optic cable. Do not discard the cap. When you are

not using the optical jack, be sure to put the cap back in

place. This cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your monitor.

The signals input through the S VIDEO jacks on this unit

are automatically converted for output through the VIDEO

jacks. When VIDEO CONV. is set to ON (see page 64),

signals input through the VIDEO jacks can be output

through the S VIDEO and COMPONENT VIDEO jacks.

Likewise, signals input through the S VIDEO jacks can

also be output through the COMPONENT VIDEO jacks.

VIDEO jacks

For conventional composite video signals.

S VIDEO jacks

For S-video signals, separated into luminance (Y) and

color (C) video signals to achieve high-quality color

reproduction.

COMPONENT VIDEO jacks

For component signals, separated into luminance (Y) and

color difference (P

B, PR) to provide the best quality in

picture reproduction.

When signals are input through both the S VIDEO and VIDEO

jacks, signals input through the S VIDEO jack have priority.

CONNECTIONS

Before connecting components

Note

CAUTION

S

V

O

V

L

R

C

Y

P

B

PR

left analog cables

right analog cables

optical cables

coaxial cables

video cables

S-video cables

For analog signals

For digital signals

For video signals

component video cables

Note

VIDEO

S VIDEO

COMPONENT VIDEO

P

R

P

B

Y

S VIDEO

VIDEO

COMPONENT

VIDEO

Signal flow inside this unit

Only when VIDEO CONV. is set to ON

(see page 64).

Output

(MONITOR OUT)

Input

16

CONNECTIONS

■ Connections for DVD playback

Be sure to connect your video source components in the same way you connect your video monitor to this unit if VIDEO CONV. (see

page 64) is set to OFF. For example, if you connect your video monitor to this unit using a VIDEO connection, connect your video

source components to this unit using the VIDEO connections. (Even when VIDEO CONV. is set to OFF, S-video signals input from

your video source component are automatically converted to composite signals in this unit.)

Connecting video components

Note

VIDEO

AUDIO

DIGITAL

INPUT

DVD

COAXIAL

DVD

MONITOR

OUT

DVD

COMPONENT VIDEO

PR PB Y

VIDEO S VIDEO

MONITOR OUT

S

P

R PB Y

V

LRC

O

DVD player

Video

monitor

Optical out

Video out

Audio out

Video in

Coaxial out

17

CONNECTIONS

PREPARATION

English

■ Connecting to the MULTI CH INPUT jacks

This unit is equipped with 8 additional input jacks (left and right FRONT, CENTER, left and right SURROUND, left and

right SURROUND BACK and SUBWOOFER) for discrete multi-channel input from a multi-format player, external

decoder, sound processor or pre-amplifier.

Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to

match the left and right outputs to the left and right input jacks for the front and surround channels.

• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you

cannot select sound field programs.

• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that

you connect at least a 5.1-channel speaker system before using this feature.

• When headphones are used, only front left and right channels are output.

Notes

SUB

WOOFER

SURROUND

FRONT

CENTER

MULTI CH INPUT

LRLR

SUB

WOOFER

SURROUND

BACK

SURROUND

FRONT

CENTER

MULTI CH INPUT

LR LRLR

Multi-format player/

External decoder

For 6-channel input

Front

out

Surround

out

Subwoofer

out

Center

out

Multi-format player/

External decoder

Front

out

Surround

out

Subwoofer

out

Center

out

Surround

back out

For 8-channel input

18

CONNECTIONS

■ Connections for other video components

• Be sure to connect your video source components in the same way you connect your video monitor to this unit if VIDEO CONV. (see

page 64) is set to OFF. For example, if you connect your video monitor to this unit using a VIDEO connection, connect your video

source components to this unit using the VIDEO connections.

• Converted video signals are only output to MONITOR OUT jacks. When recording, you must make the same type of video

connections (i.e., S-video) between each component.

■ VIDEO AUX jacks (on the front panel)

Use these jacks to connect any video source, such as a

game console or video camera, to this unit.

Notes

AUDIO

DIGITAL

INPUT

COAXIAL

DTV/CBL

VIDEO

DTV/

CBL

COMPONENT VIDEO

PR PB Y

DTV/

CBL

IN

VCR 1

OUT

O

LR

MONITOR

OUT

S

V

S

V

S

P

R PB Y

VIDEO S VIDEO

MONITOR OUT

Cable TV or

satellite tuner

DVD recorder

or VCR

Audio out

Video out

Optical out

Audio out

Video out

Video inAudio in

Video

monitor

Video in

or or

VIDEOS VIDEO OPTICALL AUDIO R

VIDEO AUX

O

V

S

L

R

Game

console or

video

camera

Video out

Audio out L

Audio out R

Optical out

S-video out

Sayfa yükleniyor ...

Yamaha RX-V757 El kitabı

Yamaha RX-V757 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler