Yamaha YSP-1000 El kitabı

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

YSP-1000

Printed in Malaysia WG11470

YSP-1000

Digital Sound Projector

Système Acoustique Numérique

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

RX-V4600_GB-cv.fm Page 1 Wednesday, August 31, 2005 6:58 PM

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place with at least 5 cm of space above (or below) this unit –

away from direct sunlight, heat sources, vibration, dust, moisture,

and/or cold.

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power supply cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. YAMAHA will

not be held responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

14 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

15 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

16 Before moving this unit, press STANDBY/ON to set this unit in

standby mode, and disconnect the AC power plug from the wall

outlet.

17 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power supply cable from the

outlet, then leave the unit alone.

18 When using the unit for a long time, the unit may become warm.

Turn the power off, then leave the unit alone for cooling.

19 Install this unit near the wall outlet and where the AC power plug

can be reached easily.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING

THE POWER SUPPLY CABLE OF THIS UNIT MUST BE

CONNECTED TO THE MAIN SOCKET OUTLET VIA A

PROTECTIVE EARTHING CONNECTION.

This unit is not disconnected from the AC power source as long

as it is connected to the AC wall outlet, even if this unit itself is

turned off. This state is called the standby mode. In this state,

this unit is designed to consume a very small quantity of power.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below. Note that the plug severed from

the mains lead must be destroyed, as a plug with bared

flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED. Make sure that neither core is connected to the

earth terminal of the three pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radi-

ation exposure.

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

SETUP

English

OVERVIEW ........................................................... 2

FEATURES............................................................. 3

USING THIS MANUAL ........................................ 4

SUPPLIED ACCESSORIES ................................. 5

CONTROLS AND FUNCTIONS ......................... 6

Front panel ................................................................. 6

Front panel display .................................................... 7

Rear panel .................................................................. 8

Remote control........................................................... 9

INSTALLATION ................................................. 11

Before installing this unit......................................... 11

Installing this unit .................................................... 11

CONNECTIONS .................................................. 15

Connecting a TV...................................................... 16

Connecting a DVD player/recorder ......................... 17

Connecting a VCR................................................... 18

Connecting a digital satellite tuner

or a cable TV tuner.............................................. 19

Connecting a digital airwave tuner .......................... 20

Connecting other external components ................... 21

Connecting a subwoofer .......................................... 22

Affixing the optical cable ........................................ 23

Connecting the power supply cable......................... 23

About the RS-232C/REMOTE IN/

IR-OUT terminals................................................ 23

GETTING STARTED.......................................... 24

Installing batteries in the remote control ................. 24

Operation range of the remote control..................... 24

Using the remote control ......................................... 25

Turning on the power............................................... 25

USING SET MENU.............................................. 26

Displaying the OSD................................................. 26

The flow chart of SET MENU................................. 27

AUTO SETUP....................................................... 28

The flow chart of AUTO SETUP ............................ 28

Installing the optimizer microphone........................ 29

Using AUTO SETUP .............................................. 31

USING THE SYSTEM MEMORY .................... 36

Saving settings......................................................... 36

Loading settings....................................................... 37

PLAYBACK ..........................................................39

Selecting the input source........................................ 39

Playing back sources ............................................... 40

Adjusting the volume............................................... 40

Muting the sound ..................................................... 41

BEAM MODE .......................................................42

5 beam mode............................................................ 43

Stereo plus 3 beam mode......................................... 43

3 beam mode............................................................ 44

Stereo mode ............................................................. 44

Target mode............................................................. 45

ENJOYING SURROUND SOUND.....................46

Enjoying 2-channel sources

in surround sound ................................................ 47

Enjoying TV in surround sound .............................. 48

Adjusting surround mode parameters...................... 49

USING SOUND FIELD PROGRAMS................51

What is a sound field? ............................................. 51

Sound field program descriptions............................ 52

Turning on CINEMA DSP programs ...................... 53

Turning off CINEMA DSP programs ..................... 55

Adjusting CINEMA DSP levels .............................. 55

USING THE VOLUME MODE ..........................56

USING TruBass.....................................................58

USING THE SLEEP TIMER ..............................60

Setting the sleep timer ............................................. 60

Canceling the sleep timer ........................................ 61

BASIC SETUP.......................................................62

MANUAL SETUP.................................................68

Using MANUAL SETUP........................................ 69

BEAM MENU ......................................................... 70

SOUND MENU....................................................... 74

INPUT MENU......................................................... 77

DISPLAY MENU.................................................... 79

ADJUSTING SYSTEM PARAMETERS ...........80

Setting the maximum volume level ......................... 80

Protecting the current settings ................................. 81

Initializing the current settings ................................ 82

Adjusting the audio balance .................................... 83

SELECTING THE INPUT MODE .....................86

REMOTE CONTROL FEATURES ...................87

Setting remote control codes ................................... 87

Controlling other components ................................. 88

Using the TV macro ................................................ 90

TROUBLESHOOTING .......................................92

GLOSSARY...........................................................95

Audio formats .......................................................... 95

Audio information ................................................... 95

INDEX....................................................................96

SPECIFICATIONS...............................................97

CONTENTS

INTRODUCTION

PREPARATION

SETUP

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

OVERVIEW

2

It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of

wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of

surround sound experience as your local movie theater.

YAMAHA YSP-1000 Digital Sound Projector challenges this preconception that complicated speaker setup and

troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.

This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is

not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been

waiting for from its built-in subwoofers (2) and individual speakers (40).

You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly

directional sound that comes in on the listening position from all directions.

The YSP-1000 projects sound beams containing surround sound information for the front right (R), front left (L),

surround right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room

before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector

creates true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.

Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.

OVERVIEW

SL

SR

R

L

C

Listening position

Imaginary

surround left

speaker

Imaginary

surround right

speaker

Imaginary

front left

speaker

Imaginary

front right

speaker

Imaginary

center

speaker

FEATURES

3

INTRODUCTION

English

Digital Sound Projector

This unit employs the digital sound projector technology

that allows one slim unit to control and steer multiple

channels of sound to generate full, physical 5.1 channel

surround sound, thus eliminating the need for satellite

loudspeakers and cabling normally associated with

conventional surround sound systems. This unit is also

equipped with the following 5 beam modes so that you can

choose the behavior of sound beams that best matches

your listening environment.

◆ 5 beam mode

◆ ST(STEREO)+3 beam mode

◆ 3 beam mode

◆ Stereo mode

◆ Target mode

Cinema DSP Digital

This unit employs the Cinema DSP Digital technology

developed by YAMAHA Electronics Corp. so that you can

experience movies at home with all the dramatic sound

impact that the director intended to convey.

OSD (on-screen display)

This unit employs the OSD which is basically a

superimposed screen image displayed on your video

monitor. The OSD is used to display the system

information or adjust settings for the system parameters.

Versatile Remote Control

The supplied remote control come with preset remote

control codes to be used to control the DVD player, VCR,

cable TV tuner and digital satellite tuner connected to this

unit. In addition, the remote control is equipped with the

macro capability so that you can perform a series of

operations with the press of a single button.

AUTO SETUP

This unit employs the automatic sound beam optimization

using the YAMAHA Parametric Room Acoustic

Optimizer (YPAO) technology with the aid of the supplied

optimizer microphone so that you can avoid troublesome

listening-based speaker setup and achieve highly accurate

sound beam adjustments that best match your listening

environment.

Compatibility with the Newest Technologies

This unit employs decoders compatible with Dolby

Digital, DTS (Digital Theater Systems), Dolby Pro Logic,

Dolby Pro Logic II and DTS Neo:6.

◆ Dolby Digital

This is the standard audio signal format used on DVDs and

other purely digital media. This surround technology deliver

high-quality digital audio for up to 5.1 discrete channels to

produce a directional and more realistic effect.

◆ DTS (Digital Theater Systems)

This is an audio signal format used on DVDs and other purely

digital media. This surround technology deliver high-quality

digital audio for up to 5.1 discrete channels to produce a

directional and more realistic effect.

◆ Dolby Pro Logic

This sophisticated, matrix decoding technology up-converts

any 2 channel source audio to a surround sound playback.

◆ Dolby Pro Logic II

This is fundamentally a redesigned version of Dolby Pro

Logic that employs 2 stereo surround channels, a subwoofer

and a greatly enhanced steering logic. As a result, this

improved technology provides an exceptionally stable sound

field that simulates 5.1 to a much greater degree than the

original Dolby Pro Logic. In addition, Dolby Pro Logic II

features Movie, Music and Game modes specifically designed

for movies, music and games respectively.

◆ DTS Neo:6

This technology decodes the conventional 2 channel sources

for maximum 6 channel playback, enabling playback with the

full-range channels with higher separation. This unit is

equipped with the 5 channel playback mode. Music mode and

Cinema mode are available to play back music and movie

sources respectively.

The “ ” logo and “Cinema DSP” are registered

trademarks of YAMAHA Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, and “Neo:6” are trademarks of Digital Theater Systems,

Inc.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.

The ‘ ’ logo and ‘Digital Sound Projector

™

’ are trademarks

of 1 Ltd.

TruBass, SRS and the “ ” symbol are registered trademarks

of SRS Labs, Inc. TruBass technology is incorporated under

license from SRS Labs, Inc.

FEATURES

USING THIS MANUAL

4

• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the

supplied owner’s manual for the component.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases, the operation is

described using remote control operation.

• y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

1 Install this unit in your listening room.

See “INSTALLATION” on page 11.

2 Connect this unit to your TV and other external components.

See “CONNECTIONS” on page 15.

3 Prepare the remote control and turn on the power of this unit.

See “GETTING STARTED” on page 24.

4 Run AUTO SETUP.

See “AUTO SETUP” on page 28.

5 Play back a source and enjoy surround sound.

See “PLAYBACK” on page 39.

6 Run MANUAL SETUP and set remote control codes to fine-tune settings.

See “MANUAL SETUP” on page 68 and “REMOTE CONTROL FEATURES” on page 87.

USING THIS MANUAL

Notes

If you want to make additional settings

and adjustments

SUPPLIED ACCESSORIES

5

INTRODUCTION

English

Check that you have received all of the following parts.

SUPPLIED ACCESSORIES

TV

POWER

2

1

STEREO

SLEEP

CH LEVEL MENU

RETURN

TEST

TV VOL

VOLUME

MUTE TV INPUT TV MUTE

ENTER

SURROUND

OFF

CODE SET

SPORTS

AV

POWER

STANDBY/ON

3

4

56

789

0

+10

5BEAM

ST+3BEAM

3BEAM

TARGET

MUSIC MOVIE VOL MODE

INPUTMODE

MACROINPUT2INPUT1

TV

STBVCRDVD

AUX

YSP

CINEMA DSP

CH

TV

Remote control (×1)

Batteries (×2)

(AA, R6, UM-3)

Video pin cable (×1)

Optimizer microphone (×1)

Fastener (×4)

Audio pin cable (×1)

Digital audio pin cable (×1)

Optical cable (×1)

Cable clamp (×1)

Cardboard microphone

stand (×1)

(Orange)

(White/Red)

(Yellow)

Power supply cable (×1)

CONTROLS AND FUNCTIONS

6

1 OPTIMIZER MIC jack

Use to connect the supplied optimizer microphone to be

used to run AUTO SETUP (see page 28).

2 Front panel display

Shows information about the operational status of this

unit.

3 Remote control sensor

Receives infrared signals from the remote control.

4 INPUT

Press repeatedly to switch between input sources (TV,

STB, VCR, DVD or AUX). See page 39 for details.

5 VOLUME –/+

Controls the volume level of all audio channels

(see page 40).

6 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 25).

• When you turn on the power of this unit, you will hear a click

and there will be a 4 to 5-second delay before it can reproduce

sound.

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared-signals from the remote

control.

CONTROLS AND FUNCTIONS

Front panel

2

3

4

1

5

6

STANDBY/ONVOLUME

+

INPUT

Notes

CONTROLS AND FUNCTIONS

7

INTRODUCTION

English

1 NIGHT indicator

Lights up when you select a volume mode (see page 56).

2 SLEEP indicator

Lights up when the sleep timer is turned on (see page 60).

3 Decoder indicators

Light up when the corresponding decoder of this unit is in

operation (see page 46).

4 Volume level indicator

Shows the current volume level (see page 40).

5 Multi-information display

Shows information when you adjust the parameters of this

unit.

y

You can adjust the brightness of the front panel display using the

DISPLAY MENU parameters in MANUAL SETUP (see

page 79).

Front panel display

NIGHT SLEEP PCM PL

m

ft

mS

dB

VOL

DIGITAL

5

412 3

CONTROLS AND FUNCTIONS

8

1 RS-232C/REMOTE IN terminals

These are control expansion terminals for factory use only

(see page 23).

2 DVD COAXIAL DIGITAL IN jack

Use to connect a DVD player/recorder via a coaxial digital

connection (see page 17).

3 AUX OPTICAL DIGITAL IN jack

Use to connect an external component via an optical

digital connection (see page 21).

4 TV/STB OPTICAL DIGITAL IN jack

Use to connect a TV, a digital satellite tuner or a cable TV

tuner via an optical digital connection

(see page 16, 19 and 20).

5 TV/STB AUDIO IN jacks

Use to connect a TV, a digital satellite tuner or a cable TV

tuner via an analog audio connection

(see page 16, 19 and 20).

6 VCR AUDIO IN jacks

Use to connect a VCR via an analog audio connection

(see pages 17 and 18).

7 SUBWOOFER jack

Use to connect a subwoofer (see page 22).

8 VCR VIDEO IN jack

Use to connect a VCR via a composite analog video

connection (see page 18).

9 DVD/AUX VIDEO IN jack

Use to connect a DVD player/recorder or an external

component via a composite analog video connection

(see page 17).

0 DVD/AUX COMPONENT VIDEO IN jacks

Use to connect a DVD player/recorder or an external

component via a component analog video connection

(see page 17).

A STB VIDEO IN jack

Use to connect a digital satellite tuner or a cable TV tuner

via a composite analog video connection

(see pages 19 and 20).

B STB COMPONENT VIDEO IN jacks

Use to connect a digital satellite tuner or a cable TV tuner

via a component analog video connection

(see pages 19 and 20).

C VIDEO OUT jack

Use to connect to the video input jack of your TV via a

composite analog video connection to display the OSD of

this unit (see page 16).

D COMPONENT VIDEO OUT jacks

Use to connect to the video input jacks of your TV via a

component analog video connection to display the OSD of

this unit (see page 16).

E IR-OUT terminal

This is a control expansion terminal for factory use only

(see page 23).

F AC IN

Use to connect the supplied power supply cable

(see page 23).

Rear panel

REMOTE IN

RS-232C

VIDEO OUTVIDEO INAUDIO IN

OPTICAL

DIGITAL IN

VCR

VCR STB

AUX

DVD/AUX

DVD

COAXIAL

TV/STB

COMPONENT COMPONENT COMPONENT

SUBWOOFER

123 654798CA

DB0

EF

CONTROLS AND FUNCTIONS

9

INTRODUCTION

English

This section describes the function of each control on the

remote control used to control this system.

y

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 88 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Sets this system to the standby mode (see page 25).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (TV, STB, VCR, DVD or

AUX) and change the control area (see page 39).

5 TruBass

Use to effectively reproduce the bass sound (see page 58).

6 YSP

Switches to the operation mode of this unit.

7 Numeric buttons

Use to enter numbers.

8 Sound field program buttons

Use to select sound field programs (see page 51).

9 CH LEVEL

Adjusts the volume level of each channel (see page 84).

0 Cursor buttons / / / , ENTER

Use to select and adjust SET MENU items.

A TEST

Outputs a test tone when adjusting the output level of each

speaker (see page 83).

B VOLUME +/–

Increases or decreases the volume level of this unit (see

page 40).

C MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 41).

D TV INPUT

Switches the input source of the TV (see page 88).

E DVD player/VCR control buttons

Use to control the DVD player of the VCR (see pages 88

and 89).

F TV POWER

Turns on the power of the TV or sets it to the standby

mode (see page 88).

G AV POWER

Turns on the power of the selected component or sets it to

the standby mode (see pages 88 and 89).

H INPUT1/INPUT2

Selects the input source of the TV.

Remote control

TV

POWER

2

1

STEREO

SLEEP

CH LEVEL MENU

RETURN

TEST

TV VOL

VOLUME

MUTE TV INPUT TV MUTE

ENTER

SURROUND

OFF

CODE SET

SPORTS

AV

POWER

STANDBY/ON

3

4

56

789

0

+10

5BEAM

ST+3BEAM

3BEAM

MUSIC MOVIE VOL MODE

INPUTMODE

MACROINPUT2INPUT1

TV

STBVCRDVD

AUX

YSP

CINEMA DSP

CH

TARGET

TV

1

2

4

6

7

9

0

A

E

I

J

N

K

O

P

Q

S

5

3

H

M

8

L

D

C

R

B

G

F

CONTROLS AND FUNCTIONS

10

I MACRO

Use to set the TV macro (see page 90).

J INPUTMODE

Switches between input modes (AUTO, DTS or

ANALOG). See page 39 for details.

K SLEEP

Sets the sleep timer (see page 60).

L Beam mode buttons

Change the beam mode settings (see page 42).

M VOL MODE

Turns on or off the volume modes (see page 56).

N SURROUND

Selects the surround mode for playback (see page 46).

O MENU

Displays the setup menu on your TV monitor (see

pages 31, 62 and 69).

The DVD menu is displayed when DVD is selected as the input

source.

P RETURN

Use to select sleep timer settings or return to the previous

SET MENU screen.

Q TV VOL +/–

Adjusts the volume level of the TV (see page 88).

R CH +/–

Switches between channels of the TV or the VCR (see

pages 88 and 89).

S TV MUTE, CODE SET

Mutes the audio output of the TV (see page 88).

Use to set up remote control codes (see page 87).

Note

INSTALLATION

11

PREPARATION

English

This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.

This unit creates surround sound by reflecting projected

sound beams off the walls of your listening room. The

surround sound effects produced by this unit may not be

sufficient when the unit is installed in the following

locations.

• Rooms with surfaces inadequate for reflecting sound

beams

• Rooms with acoustically absorbent surfaces

• Rooms with measurements outside the following range

W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)

• Rooms with less than 2 m from the listening position to

the speaker positions

• Rooms where objects such as furniture are likely to

obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of

this unit

Make sure you leave an adequate amount of ventilation

space so that heat can escape. Make at least 5 cm of space

above or below this unit.

• This unit weighs 13.0 kg. Be sure to install this unit where it

will not fall subject to vibrations, such as from an earthquake,

and where it is out of the reach of children.

• When using a cathode-ray tube (CRT) TV, do not install this

unit directly above your TV.

• This unit is shielded against magnetic rays. However, if the

picture on your TV screen becomes blurred or distorted, we

recommend moving the speakers away from your TV.

Install this unit where there are no obstacles such as

furniture obstructing the path of sound beams. Otherwise,

the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the

corner.

■ Parallel installation

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

■ Corner installation

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

y

The availability of the beam mode depends on the installation

location of this unit (see page 42). All five beam modes are

available for the parallel installation whereas the 3 beam and 5

beam modes are not available for the corner installation.

INSTALLATION

Before installing this unit

Notes

5 cm or more

RearFront

Side view

Side

Installing this unit

An object, such as furniture

40° to 50°

An object, such as furniture

12

INSTALLATION

■ Installation examples

Example 1

Install this unit as close to the exact center of the wall as possible.

Example 2

Install this unit so that the sound beams can be reflected off the walls.

Example 3

Install this unit as close to the exact front of your normal listening position.

13

INSTALLATION

PREPARATION

English

■ Using a metal wall bracket

You can use the optional metal wall bracket to mount this

unit on the wall in your listening room.

y

Refer to the instructions supplied with the metal bracket for

details on how to attach the metal bracket to the wall or how to

attach this unit to the metal bracket.

■ Using a stand

You can mount your TV on the stand placed on a

commercially available rack to install this unit under your

TV.

y

Refer to the instructions supplied with the stand for details on

how to install the stand or how to mount this unit and the TV on

the stand.

■ Using a TV stand

You can use the optional TV stand to install this unit. For

detailed information on installing this unit using a TV

stand, refer to the installation manual supplied with the

optional TV stand.

■ Using a rack

You can install this unit either above or under your TV in a

commercially available rack.

Make sure that the rack is large enough to allow adequate

ventilation space around this unit (see page 11) and that it is

strong enough to support the weight of both this unit and your TV.

This unit

TV

Metal wall bracket

TV

This unit

Stand

Note

This unit

TV

When this unit is installed above your TV

When this unit is installed under your TV

14

INSTALLATION

■ Affixing this unit

Peel off the film from each of the four supplied fasteners

and then secure them to the bottom four corners of this

unit and the top of the rack, etc.

• Do not install this unit on top of a slanted surface. This unit may

fall over and cause injury.

• Make sure you wipe the surface of the rack, etc. before securing

the fasteners. Applying the tape to a dirty or wet surface will

weaken the sticking power of the tape, and this unit may fall as

a result.

Notes

2

1

This unit

Peel off

the film

Fasteners

Peel off

the pad

on the

bottom

CONNECTIONS

15

PREPARATION

English

This unit is equipped with the following types of audio/video input/output jacks:

For audio input

• 2 optical digital input jacks

• 1 coaxial digital input jack

• 2 sets of analog input jacks

For video input

• 3 composite analog input jacks

• 2 sets of component analog input jacks

For video output

• 1 composite analog output jack

• 1 set of component analog output jacks

Use these audio/video input/output jacks to connect external components such as your TV, DVD player, VCR, digital

satellite tuner, cable TV tuner and game console. Further, by connecting a subwoofer to this unit, you can enjoy

reinforced low bass sounds. For details on how to connect various types of external components to this unit, see pages 16

to 22.

Do not connect this unit or other components to the main power until all connections between components are complete.

CONNECTIONS

CAUTION

Audio connection

Video connection

DVD player Subwoofer

This unit

VCR Digital satellite tuner, cable TV

tuner or game console

TV

16

CONNECTIONS

Connect a TV to this unit and display the OSD for easy viewing when you adjust the system parameters in SET MENU.

■ Audio connections

Connect the analog audio output jacks of your TV to the

TV/STB AUDIO IN jacks of this unit. If your TV has an

optical digital output jack, connect the optical digital

output jack of your TV to the TV/STB OPTICAL

DIGITAL IN jack of this unit in addition to the analog

audio connection. Once the digital audio connection is

made, digital audio signals can be input to this unit during

digital broadcasting.

■ Video connections

Connect the video input jacks of your TV to the VIDEO

OUT jacks of this unit. If your TV has component video

input jacks, connect the component video input jacks of

your TV to the COMPONENT VIDEO OUT jacks of this

unit in addition to the composite video connection. Once

the component video connection is made, you can enjoy

images with better resolution.

y

• The circuits of composite and component video signals are independent of each other.

• To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 23).

If you connect this unit to the analog audio and optical digital audio output jacks at the same time as shown in the left illustration below,

the digital audio signals output at the optical digital output jack take priority over the analog audio signals output at the analog audio

output jacks.

Cables used for audio connections Cables used for video connections

Connecting a TV

Note

REMOTE IN

RS-232C

VIDEO OUTVIDEO INAUDIO IN

OPTICAL

DIGITAL IN

VCR

VCR STB

AUX

DVD/AUX

DVD

COAXIAL

TV/STB

SUBWOOFER

COMPONENT COMPONENT COMPONENT

Rear panel of this unit

TV

Optical digital

output

Analog audio

output

RL

Video

input

Component

video input

Optical cable (supplied)

Audio pin cable (supplied)

(White)

(Red)

(White)

(Red)

Video pin cable (supplied)

(Yellow)(Yellow)

Component video pin cable

(Green)

(Blue)

(Red)

(Green)

(Blue)

(Red)

17

CONNECTIONS

PREPARATION

English

Connect a DVD player/recorder and enjoy DVDs.

■ Audio connections

Connect the optical digital output jack of your DVD

player/recorder to the DVD COAXIAL DIGITAL IN jack

of this unit. In case you connect this unit to a DVD/VCR

combo player/recorder, connect the analog audio output

jacks of your DVD/VCR combo player/recorder to the

VCR AUDIO IN jacks of this unit in addition to the

optical digital audio connection.

■ Video connections

Connect the video output jack of your DVD player/

recorder to the DVD/AUX VIDEO IN jack of this unit. If

your DVD player/recorder has component video output

jacks, connect the component video output jacks of your

DVD player/recorder to the DVD/AUX COMPONENT

VIDEO IN jacks of this unit. Once the component video

connection is made, you can enjoy images with better

resolution.

y

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 23).

• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system

settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.

• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead

(see page 21).

Cables used for audio connections Cables used for video connections

Connecting a DVD player/recorder

Notes

COMPONENT COMPONENT COMPONENT

REMOTE IN

RS-232C

VIDEO OUTVIDEO INAUDIO IN

OPTICAL

DIGITAL IN

VCR

VCR STB

AUX

DVD/AUX

DVD

COAXIAL

TV/STB

SUBWOOFER

Rear panel of this unit

DVD player/recorder

Coaxial digital

output

Analog audio

output

RL

Video

input

Component

video input

You can only make either a

composite or a component

video connection.

Note

*

In case you connect this

unit to a DVD/VCR

combo player/recorder

Note

*

Audio pin cable

(White)

(Red)

(White)

(Red)

Digital audio pin cable (supplied)

(Orange)

Video pin cable

(Yellow)(Yellow)

Component video pin cable

(Green)

(Blue)

(Red)

(Green)

(Blue)

(Red)

18

CONNECTIONS

Connect a VCR and enjoy video cassette tapes.

■ Audio connections

Connect the analog audio output jacks of your VCR to the

VCR AUDIO IN jacks of this unit.

■ Video connections

Connect the video output jack of your VCR to the VCR

VIDEO IN jack of this unit.

Be sure to match the left and right output jacks of your VCR with the left and right input jacks of this unit.

Cables used for audio connections Cables used for video connections

Connecting a VCR

Note

REMOTE IN

RS-232C

VIDEO OUTVIDEO INAUDIO IN

OPTICAL

DIGITAL IN

VCR

VCR STB

AUX

DVD/AUX

DVD

COAXIAL

TV/STB

SUBWOOFER

COMPONENT COMPONENT COMPONENT

Rear panel of this unit

Analog audio

output

RL

VCR

Video

output

Audio pin cable

(White)

(Red)

(White)

(Red)

Video pin cable

(Yellow)(Yellow)

Sayfa yükleniyor ...

Yamaha YSP-1000 El kitabı

Yamaha YSP-1000 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler