Yamaha BBT500H El kitabı

Marka: Yamaha

Model: BBT500H

Kategori: Tamamlayıcı müzik ekipmanı

Tip: El kitabı

Bu kılavuz için de uygundur

BBT 500H

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

BASS AMPLIFIER

BBT500H

Manual del Usuario

Handleiding

Manuale di Istruzioni

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in your

plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your au-

thority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your use

of this product in a residential environment will not result in

harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not in-

stalled and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur in all

installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is being af-

fected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-

003 du Canada.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. In-

stall in accordance with the manufacturer's

instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that pro-

duce heat.

9 Do not defeat the safety purpose of the po-

larized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong are provided for your

safety. If the provided plug does not fit into

your outlet, consult an electrician for re-

placement of the obsolete outlet.

IMPORTANT SAFETY INSTRUCTIONS

10 Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

11 Only use attachments/accessories specified

by the manufacturer.

12 Use only with the cart,

stand, tripod, bracket, or

table specified by the

manufacturer, or sold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14 Refer all servicing to qualified service per-

sonnel. Servicing is required when the appa-

ratus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into

the apparatus, the apparatus has been ex-

posed to rain or moisture, does not operate

normally, or has been dropped.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS: Yamaha electronic prod-

ucts may have either labels similar to the graphics shown be-

low or molded/stamped facsimiles of these graphics on the

enclosure. The explanation of these graphics appears on this

page. Please observe all cautions indicated on this page and

those indicated in the safety instruction section.

ENVIRONMENTAL ISSUES: Yamaha strives to produce

products that are both user safe and environmentally friendly.

We sincerely believe that our products and the production meth-

ods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware

of the following:

Warning: Do not attempt to recharge, disassemble, or inciner-

ate this type of battery. Keep all batteries away from children.

Dispose of used batteries promptly and as regulated by appli-

cable laws. Note: In some areas, the servicer is required by law

to return the defective parts. However, you do have the option

of having the servicer dispose of these parts for you.

Disposal Notice: Should this product become damaged beyond

repair, or for some reason its useful life is considered to be at an

end, please observe all local, state, and federal regulations that

relate to the disposal of products that contain lead, batteries,

plastics, etc.

NOTICE: Service charges incurred due to lack of knowledge

relating to how a function or effect works (when the unit is

operating as designed) are not covered by the manufacturer’s

warranty, and are therefore the owners responsibility. Please

study this manual carefully and consult your dealer before re-

questing service.

NAME PLATE LOCATION: The graphic below indicates the

location of the name plate and serial number label. Information

such as model number, power requirements, serial number, etc.,

can be found at these two locations. You should record the model

number, serial number, and the date of purchase in the spaces

provided below and retain this manual as a permanent record

of your purchase.

See rear of Amplifier for graphic symbol markings.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead sym-

bol, within the equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute

a risk of electrical shock.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT NOTICE: All Yamaha electronic products are

tested and approved by an independent safety testing labora-

tory in order that you may be sure that when it is properly in-

stalled and used in its normal and customary manner, all fore-

seeable risks have been eliminated. DO NOT modify this unit

or commission others to do so unless specifically authorized by

Yamaha. Product performance and/or safety standards may be

diminished. Claims filed under the expressed warranty may be

denied if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The infor-

mation contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change

or modify any of the specifications without notice or obligation

to update existing units.

92-469-① (rear)

Model

Serial No.

Purchase Date

● Avoid using your amplifier and speaker in the following locations

to prevent possible damage:

• In direct sunlight or next to heating equipment.

• Extremely cold or hot locations.

• Locations exposed to high humidity or excessive dust.

• Locations subject to strong shocks or vibration.

● Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

• Other components, as they may cause damage and/or

discoloration on the surface of this unit.

• Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

• Containers with liquid in them, as they may fall and liquid may

cause electrical shock to the user and/or damage to this unit.

● Before making any connections, make sure that the power on

the amplifier and any external devices is switched OFF.

● To protect the speaker from possible damage, always set the

OUTPUT knob to “0” before switching the power ON/OFF.

● When connecting the speaker jack to a speaker, use only a

cable designed specifically for connecting a speaker to the

amplifier. The use of any other cable can result in fire.

● Even if the device’s main power switch is switched OFF, power

is not cut off from the device. Place the device close to an easily

accessible electric outlet so it can be plugged in or unplugged

with ease.

● Your Yamaha amplifier is a precision musical instrument. Handle

it with care and avoid dropping or bumping it.

● Do not apply excessive force to the switches and controls.

● To prevent damage and possibly electrical shock, never open

the case and tamper with the internal circuitry.

● Do not block the ventilation ducts. The device is designed with

ducts on the front and back to prevent temperatures from rising

inside the device. Blocking the ducts will cause heat to buildup

Precautions

inside the device, which may result in fire. NEVER operate the

device in any of the manners described below.

* Never place the device on its back, side, or upside-down.

* Install the device in anything other than the specified rack, such in a

narrow bookshelf, in an small enclosed space, or a place with poor

ventilation, etc.

* Cover the device with a cloth or place the device on a carpet or bed.

● When the devices is installed in an audio rack, etc., make sure

that there is sufficient space between the wall or other equip-

ment, and the device. The device requires clearance of at least

5cm on its sides, 10cm at the back, and 10cm above.

Also, open the rear of the rack, or open a hole in the back of the

rack to provide the device with ventilation.

Poor ventilation will cause heat to buildup inside of the device,

which can result in fire.

● Never place the device on an unstable surface, table, or sloped

surface. Also, never stack the device excessively. Doing so may

cause the device to fall or overturn, causing injury.

* If the device is to be stacked, we recommend that the casters be removed

from the amplifier/speaker to prevent overturning.

● During thunderstorms, switch off the power as soon as possible

and unplug the device from the electric outlet. If there are

lightning strikes, do not touch the power cable if it is still

connected to the electric outlet. Doing so can result in electric

shock.

● For safety, always remove the power plug from the AC wall

outlet if there is any danger of lightning striking in your area.

● Do not use the amplifier for any other purpose than powering a

speaker system.

● Keep the amplifier away from neon signs or fluorescent lighting

to prevent noise pickup.

● Never use benzene, thinner or other volatile liquids for cleaning,

as these chemicals may cause damage or discoloration to the

finish. Always use a dry, soft cloth to wipe off dust and dirt.

Operating Cautions!

To use in a safe manner, please obey the following

● About the XLR jack’s polarity

The pin order of the XLR type connector is as follows:

1: Shield (GND), 2: Hot (+), 3: Cold (-)

This conforms to the IEC60268 standard.

● About Cellular Phone Interference

Cellular phones used in close proximity to the device may

cause noise. If this is the case, move the phone a little

away from the device.

Thank you for purchasing the Yamaha BBT500H Bass Amplifier.

The BBT500H is an all-digital bass amplifier that utilizes Yamaha’s DSP technology to

provide bassists with extensive sound tailoring capabilities and simple operation. Thanks to the

use of a highly efficient digital power amplifier in combination with Yamaha’s power switching

technology the BBT500H can deliver an unprecedented 500W/2Ω of power from its compact

and lightweight design.

The BBT500H offers bassists precision sound tailoring and control with its 11 sound

variation types, 5-band semi-parametric equalizer, compressor, limiter, and noise gate. It is also

equipped with a speaker simulator and effects loop for greater tone tailoring and versatility. The

BBT500H provides 5 internal memory locations that let you store up to five tone settings for

instant recall at the press of a switch. It also offers MIDI compatibility and a bi-amp system

(using two amplifiers to create a single system), etc. that make it an excellent choice for use in

the studio or live performances.

In order to get the most out of your BBT500H and its sophisticated functions, please

thoroughly read this Owner’s Manual before using the device. Also, keep the manual in a safe,

convenient place for future reference.

CONTENTS

Panel Controls and Connections........................................ 7

Front Panel.................................................................................. 7

Rear Panel .................................................................................. 8

Operating Instructions ...................................................... 10

Getting sound output................................................................. 10

Adjusting the Input Level........................................................... 10

Sound Setting ........................................................................... 10

Storing and Recalling Patches .................................................. 11

Detailed Parameter Settings ............................................. 12

Amp Mode................................................................................. 12

Equalizer Mode ......................................................................... 13

Compressor Mode .................................................................... 13

Utility Mode ............................................................................... 14

Attaching the Rack Mount Adaptor .................................. 17

Air Flow ............................................................................... 17

Attaching the Clamp Filter ................................................ 17

Error Messages .................................................................. 18

Troubleshooting ................................................................. 18

Specifications..................................................................... 19

MIDI Implementation Chart ............................................... 95

Panel Controls and Connections

Front Panel

q w e r t y u i o

!1 !2 !3

q Power Switch

This is the unit’s main power switch.

* Always set the OUTPUT volume to “0” before switching the power ON or

OFF to protect the speaker from damage.

w Input Jack (INPUT)

This is the unit’s input jack.

Connect the output jack on your bass to this jack.

* Make sure that the power is switched OFF before connecting the bass.

* For U.S. and Canadian models only

To protect against electromagnetic waves, attach

the supplied Clamp Filter to the cable connecting

the bass guitar to the amplifier. (→ pg. 17)

e Input Level Volume (INPUT LEVEL)

Adjusts the amplifier’s input volume level and the volume of the bass

that is connected to the BBT500H. Use the indicators located on either

side of the knob to check the signal level. (→ pg. 10)

* The INPUT LEVEL setting is not saved in memory.

r Sound Type Select Switch (SOUND TYPE)

Select one of the eleven preset sound variation types.

The indicator of the selected sound type will light. (→ pg. 10)

t Compressor Volume (COMP)

Adjusts the compressor’s compression ratio.

In the Equalizer mode, this knob is used to set the center frequency

(PEQ F) of the 1-band parametric equalizer. (→ pg. 13)

y Gain Volume (GAIN)

Adjusts the pre-amplifier’s gain volume level.

* When this knob is set to “0”, no sound will be produced although the

Master Volume is turned up.

In the Equalizer Mode, this knob is used to set the bandwidth (PEQ Q)

of the 1-band parametric equalizer. (→ pg. 13)

In the Compressor Mode, this knob is used to set the compressor thresh-

old (THRSLD). (→ pg. 13)

u Master Volume (MASTER)

Adjusts the overall volume of the sound created with the Gain and Tone

Control settings. Adjusts the preamplifier’s output level.

* The MASTER volume setting is saved in memory.

In the Equalizer Mode, this knob is used to set the Gain (PEQ G) vol-

ume level of the 1-band graphic equalizer. (→ pg. 13)

In the Compressor Mode, this knob is used to adjust the compressor’s

attack (ATTACK) time. (→ pg. 13)

i Tone Controls

(BASS, LOW MID, MIDDLE, HIGH MID, TREBLE)

Adjusts the level of their corresponding frequencies.

In the Equalizer Mode, these knobs are used to set the center frequency

(FREQ) for their corresponding tone control. (→ pg. 13)

In the Compressor Mode, these knobs are used to adjust the param-

eters given below. (→ pg. 13)

BASS ........... Compressor’s release (RELEASE) time

LOW MID ..... Compressor’s output gain (C. GAIN)

MIDDLE ....... Compressor’s knee (KNEE)

HIGH MID .... Noise gate threshold (N. GATE)

TREBLE ....... Effect loop blend level (BLEND)

o Output Volume Level (OUTPUT)

Adjusts the power amplifier’s output level.

This knob is used to set the overall volume level (the amount delivered

by the speaker) of the sound created by the pre-amplifier section’s GAIN,

MASTER, Tone Controls, etc. Adjusting this volume level has no effect

on tone.

* The OUTPUT level setting is not saved in memory.

* This setting does not effect the output level (volume) of the LINE OUT !8

jack.

!0 Manual Switch (MANUAL)

This switch resets all parameter values (including Equalizer and Com-

pressor mode settings) to the state they were in when the power was

switched ON. All knobs function as labeled on the panel, and the setting

for each control corresponds to the position of the knob.

If you continuously hold the switch, all settings will be returned to the

state that they were in just before the [MANUAL] or Memory switch was

pressed (Undo Function). (→ pg. 12)

!1 Memory Switches (1-5)

These switches are used to recall data for patches (1-5) saved in the unit’s

memory. The selected memory’s (switch’s) indicator lights. (→ pg. 11)

After editing patch data, press and hold the switch for about 1 second to

save the data to memory. (→ pg. 11)

!2 Display

Displays information such as parameter values, etc.

!3 Function Switch (FUNCTION)

This switch is used to select the unit’s operating mode.

• Amp Mode (→ pg. 12)

• Equalizer Mode (→ pg. 13)

• Compressor Mode (→ pg. 13)

• Utility Mode (→ pg. 14)

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

8.8.8

Before making any connections, make sure that the power on

the BBT500H and all other related devices is switched OFF.

Speaker(s)

Save patches to a

MIDI device

Use a MIDI controller to select

patch memory

MIDI IN

MIDI OUT

Outboard Effects Processor

Mixer or Additional Amplifier

OUT

Panel Controls and Connections

!5 !6 !7 !8 !9 @0 @1 @2

Headphones

Tuner

AC Power

Supplied power

cable

Rear Panel

!4 Tuner Output (TUNER OUT)

This output jack is used to connect a tuner to the BBT500H.

It can also be used to create a bi-amp system. Connect this output jack

to the INPUT jack on another BBT500H. (→ pg. 14)

!5 Effect Loop (FX LOOP)

• Effect Send Jack (SEND)

• Effect Return Jack (RETURN)

• Effect Loop Level Switch (LEVEL)

These jacks let you insert an outboard effects processor between the

SEND and RETURN jacks to apply effects to the BBT500H’s signal.

Use the Level Switch to match the Input/Output level with the level re-

quired by the outboard effects processor. Use the BLEND control in the

Compressor Mode to adjust the balance level between the outboard

effector’s sound and the sound that is created by the BBT500H. (→ pg.

13)

!6 Headphones Jack (PHONES)

This jack is used to connect a pair of headphones to the unit. It carries

the same signal that is delivered from the LINE OUT jack. Use the LEVEL

control to adjust the volume.

!7 Headphones/Line Out Level Control (LEVEL)

Adjusts the output level of the PHONES jack and the LINE OUT jacks.

(The same setting is applied to both jacks.)

Line Out Jack (UNBALANCED OUT, BALANCED OUT)

These jacks carry the signal that is selected with the !9 Line Out Source

Switch at a line level.

Both unbalanced phone type (+4 dB/10 kΩ) and balanced XLR type

(+4 dB/600 Ω) jacks are provided.

Use the LINE SOURCE switch to select the signal that is sent to the

LINE OUT jack. As the unit is equipped with an output limiter and speaker

simulator (can be switched ON/OFF), and the output level of these jacks

is controlled by the LEVEL control, these jacks can be used to send a

line level signal to a mixing console or an additional amplifier.

!9 Line Out Source Switch

(LINE SOURCE: THRU/PRE EQ/POST EQ)

This switch is used to select the signal that is delivered from the LINE

OUT jack.

THRU ........... Delivers the signal received via the INPUT jack without

alteration.

Select this setting when connecting to a DI (Direct In-

jection) box.

PRE EQ ....... Delivers the signal before it has been processed by the

tone controls (the Sound Type is active).

This setting can be used when separate EQ settings

are required for speaker and line outputs.

POST EQ ..... Delivers the signal after it has been processed by the

tone controls.

Clamp Filter (→ pg. 17)

* For U.S. and Canadian

models only

* Total Impedance

Whenever two or more speaker cabinets are connected to the unit,

consideration must be given to the total impedance of the speaker

system.

Normally, a speaker cabinet has an impedance of 4, 8 or 16Ω. But

when two or more speaker cabinets are used together, the total

impedance will change according to the manner in which the cabi-

nets are connected.

● Connecting in a Series

Total impedance = 1st Speaker + 2nd Speaker + 3rd Speaker …

Connecting three 4Ω speaker cabinets in a series as shown below,

results in a total impedance of 12Ω.

Panel Controls and Connections

This setting can be used when you want the line signal

processed with the same EQ setting as the speaker.

* The FX LOOP is active on both PRE EQ and POST EQ signals.

@0 Speaker Simulator Switch (SP SIM: OFF/LINE/ON)

This switch is used to switch the Speaker Simulator circuit ON/OFF.

When the Speaker Simulator is activated, this special circuit adds the

live characteristics of a speaker to the line out signal and headphones

output. This feature is useful when you want to produce a distorted tone

with a speaker system that incorporates a tweeter, or to add the reso-

nance of a large speaker and its enclosure to a speaker system that

uses only small speakers. The sound created with the Speaker Simula-

tor is optimized to compliment the selected Sound Type.

OFF .............. Deactivates the Speaker Simulator on LINE OUT,

SPEAKER, and PHONES jack signals.

LINE ............. Activates the Speaker Simulator on LINE OUT, and

PHONES jack signals only.

ON................ Activates the Speaker Simulator on LINE OUT,

SPEAKER, and PHONES jack signals.

* The Speaker Simulator can only be applied to the LINE OUT jack output

when the !9 Line Out Source Switch is set to “POST EQ”.

@1 Output Limiter Switch (OUTPUT LIMITER: ON/OFF)

This switch is used to switch the Output Limiter circuit ON/OFF.

When set to the ON position, the limiter suppresses the signal if it ex-

ceeds the threshold before sending it to the SPEAKER jack and LINE

OUT jack.

OFF .............. Deactivates the Limiter on both LINE OUT and SPEAKER

jack signals.

ON................ Activates the Limiter on both LINE OUT and SPEAKER

jack signals.

@2 MIDI OUT Jack

Connect this jack to the MIDI IN jack on an external MIDI device that

can save MIDI data (such as a MIDI data filer, etc.), and save patch data

from the BBT500H to an external device. (→ pg. 16: MIDI Bulk Out)

Also, when MIDI Merge is set ON, MIDI data received from an external

MIDI device via the MIDI IN jack is transmitted from the MIDI OUT jack

without alteration. (→ pg. 16)

@3 MIDI IN Jack

Connect this jack to the MIDI OUT jack on MIDI Foot Controller, etc., to

select patches, control volume, etc., with the MIDI Foot Controller. (→

pg. 15)

Also, patches that have been saved to an external MIDI device can be

loaded into the BBT500H’s internal memory. (→ pg. 16: MIDI Bulk IN)

@4 Speaker Jacks (SPEAKER 1, 2)

Two Speaker Jacks are provided for connecting speaker systems.

The two jacks are connected in parallel inside the unit. Make sure that

the speaker cabinet you use meets the requirements given below.

● When using a single SPEAKER Jack (1 or 2)

Please use a system that complies with one of the following re-

quirements.

• The total impedance* of the circuit should never be less than 2Ω.

• A 2Ω speaker system must have a power handling capability of

500W or greater.

• A 4Ω speaker system must have a power handling capability of

250W or greater.

• An 8Ω speaker system must have a power handling capability of

125W or greater.

● When using both SPEAKER Jacks (1 & 2)

Please use a system that complies with one of the following re-

quirements.

• The total impedance* of the circuit should never be less than 2Ω.

• A 4Ω speaker system must have a power handling capability of

250W or greater.

• An 8Ω speaker system must have a power handling capability of

125W or greater.

To obtain optimum performance from the amplifier, we recommend that

a speaker system with a power handling capability of 250W or greater

and impedance of 4Ω be used with each SPEAKER jack (1 and 2).

* For U.S. and Canadian models only

To protect against electromagnetic waves, attach the sup-

plied Clamp Filters to the cables connecting the amplifier’s

SPEAKER 1, 2 jacks to the speakers. (→ pg. 17)

@5 Power Connector (AC IN)

Connect the supplied power cable to this terminal to supply the unit with

power from an AC power outlet.

When connecting the power cable, make sure the

amplifier’s POWER switch is turned OFF.

● Connected in Parallel

Total impedance =

Connecting three 4Ω speaker cabinets in a parallel configuration

as shown below, results in a total impedance of about 1.3Ω.

444

Sound Setting

When the power is switched ON, all control knobs function as labeled

on the panel and described below. All lamps on the display above the

control knobs and switches are unlit.

Rotate the SOUND TYPE knob to select a sound type, then use the

Tone Control knobs to shape the sound. Before selecting a sound type,

first set the GAIN through TREBLE control knobs to their center posi-

tions then try out the different Sound Types.

Also, the COMP knob is used to adjust the compressor’s compression

ratio. The compressor automatically balances the differences between

loud and soft levels when playing. Rotate the knob to the right to in-

crease the amount of compression.

q INPUT LEVEL: Sets the Input Level

w SOUND TYPE: Selects the Sound Type (11 types)

FLAT ............A clean tone with all frequencies set flat. This setting also

works well with an upright bass or an electric-acoustic bass.

TUBE........... A clear and warm tube type sound. This setting also works

well with an upright bass or an electric-acoustic bass.

SOLID .........A fat solid-state type sound

R & B ...........A fat R & B type sound

VINTAGE .....A vintage tone with warm mid frequencies

MODERN ....A modern sound with rich low-end and bright high-end

CLASSIC .....Rock bass sound

HEAVY ........A heavier sound than the CLASSIC setting

DRIVE .........Overdrive bass sound

DIST ............Distortion bass sound

FUZZ ...........Fuzz bass sound

e COMP: Compression Ratio (1.0 to ∞, 16 steps)

This adjusts the compressor’s compression ratio and output levels simul-

taneously.

As the value increases, so does the amount of compression applied to

signals that exceed the threshold level (→ pg. 13).

r GAIN: Pre-Amp Gain (0 to 10, 0.1 step)

t MASTER: Master Volume (0 to 10, 0.1 step)

y BASS: Bass Frequency (-15dB to +15dB, 0.2dB step)

u LOW MID: Low Mid Frequency (-15dB to +15dB, 0.2dB step)

i MIDDLE: Middle Frequency (-15dB to +15dB, 0.2dB step)

o HIGH MID: High mid Frequency (-15dB to +15dB, 0.2dB step)

!0 TREBLE: Treble Frequency (-15dB to +15dB, 0.2dB step)

!1 OUTPUT: Sets the output level

Getting sound output

1 First, make sure that the POWER switch is switched OFF, then

connect your bass to the INPUT Jack on the front panel.

2 Rotate the OUTPUT knob fully to the left and then switch the

POWER switch ON.

To protect the speakers, make sure that the

OUTPUT knob is set to “0” whenever switch-

ing the POWER switch ON or OFF.

Operating Instructions

w e r t y u i o !0 !1

3 First, set the INPUT LEVEL knob to its 12 O’clock position, then

while playing the bass, gradually increase the GAIN, MASTER,

and OUTPUT knobs to adjust the sound.

4 Once the system is producing sound, set the input level as

described in the “Adjusting the Input Level” section below.

Set the knob so that the red

indicator does not light.

Adjusting the Input Level

The INPUT LEVEL control optimizes the signal received from the bass

for use with the amplifier, to produce wide dynamic range and rich tone.

A poorly adjusted level results in noise, feedback, a cutup sound, etc.

* Since output levels vary from instrument to instrument, you will need to

readjust the input level to match the instrument’s output level whenever

you change instruments.

1 Rotate the volume control on your bass to its maximum level

and play loudly while rotating the INPUT LEVEL knob.

An ideal level is attained when the green indicator is lit.

2 Continue to rotate the INPUT LEVEL knob to the right making

sure the red indicator does not light. As long as the red indica-

tor does not light, rotate the knob fully to the right.

HINT Using the OUTPUT and MASTER Controls

Both knobs can be used to control the overall volume however, the

MASTER knob is the preamplifier’s master volume and its setting is

saved in memory. The OUTPUT knob is the power amplifier’s output

volume and its setting is not saved in memory. Use the MASTER knob

to set individual volume settings of patches saved to memory, and use

the OUTPUT knob to set the output volume level produced by the speak-

ers.

Operating Instructions

Setting Value

The value “4.0” flashes on the display

but rotating the knob from the “3

o’clock” position to the “11 o’clock”

position does not change anything.

As the knob goes past the “11

o’clock” position and its position

matches that of the value, the

value will then stop flashing and

start changing according to the

knob’s position.

Storing and Recalling Patches

After creating a sound that you like, you can store its settings in the

unit’s internal memory. Sound setting data (individual knob settings) is

called a Patch. Saving a patch to the unit’s internal memory is called

Store.

The BBT500H provides five memory locations for storing patch data.

Patch data in the memory is stored even when the power is switched

OFF, and can be recalled at any time by pressing the patch’s corre-

sponding switch. Take note that unless the changes are saved to memory,

any changes made to the patch will be lost when another patch is se-

lected or when the power is switched OFF.

Storing a Patch

After creating a sound you want to keep for later use, press and hold

any one of the Memory Switches (1-5) until all of the front panel indica-

tors light.

Ex.) Press and hold Memory Switch [1] until all indicators light.

* INPUT LEVEL and OUTPUT LEVEL settings are not stored in memory.

Recalling a Patch

To use one of the patches stored in memory, just press the Memory

Switch [1]-[5] to which the data is stored.

The indicator of the selected Memory Switch lights.

Ex.) Recalling the patch stored to Memory Switch [2].

● Knob Position and Settings

When a patch is recalled from memory, etc., it may be that the

knob’s actual position differs from the value set in the recalled

patch.

In this case, the BBT500H is programmed to flash the patch’s

value on the display without changing it or the sound until the

knob’s position corresponds to the value in the recalled patch

setting.

If the display flashes when rotating the knob, continue rotating

the knob until its position matches the flashing value. When the

position and value match, the value will stop flashing on the

display and change as the knob is turned.

Ex.) If the GAIN knob is pointing at the “3 o’clock” posi-

tion and a patch with a GAIN setting of 4.0 is recalled.

After you recall or store a patch, the value for each knob will appear in

the display when the knob (COMP - TREBLE) is used.

However, if the value set in the patch is different than the knob’s actual

position, the patch’s value will flash in the display but it will not change,

nor will the sound, even though you are turning the knob. For more infor-

mation on this situation, refer to the “Knob Position and Settings” sec-

tion below.

● The Useful “Undo” Function

Press and hold the [MANUAL] switch activates the “Undo” func-

tion, which returns settings to the condition they were in prior to

pressing a Memory Switch [1]-[5] or the [MANUAL] switch.

This function is useful in cases such as:

Yo u ’ve just made some changes to the patch saved in Memory

Switch [1] but pressed Memory Switch [2] before you could save

the changes to memory. Press and hold the [MANUAL] switch to

return the settings to the same condition they were in before you

pressed Memory Switch [2].

In the same manner, you made some changes to a patch but

pressed the [MANUAL] switch before you could save those

changes to memory. Press and hold the [MANUAL] button to re-

store your changes.

The BBT500H also features more precise settings for defining the fre-

quencies for each of the Tone Control knobs, operating the Compressor

and Noise Gate, or setting the Blend Level of the effect loop, etc.

To access these settings, press the [FUNCTION] switch and use the

four Modes described below.

• Amp Mode

In this mode, each knob functions in the manner it is labeled on the

front panel.

• Equalizer Mode

This mode is used to set the 1-band parametric equalizer and the

center frequency for each of the Tone Controls (Bass – Treble).

• Compressor Mode

This mode is used to set the Compressor’s blend level, noise gate

level, and effect loop.

• Utility Mode

This mode is used to set the crossover filter, and individual MIDI

settings.

Individual settings in the Amp Mode, Equalizer Mode, and Compressor

Mode are saved when patch data is saved to the unit’s memory.

Individual parameter settings in the Equalizer Mode and Compressor

Mode are set to their default values when the power is switched ON.

Individual settings in the Utility Mode are saved when exiting the Utility

Mode, and they are retained even if the power is switched OFF.

Detailed Parameter Settings

Amp Mode

Each knob functions in the manner it is labeled on the panel.

In the Amp Mode, the knob’s value (or patch’s setting value) is shown

on the display when the knob is turned.

* After the BBT500H’s power is switched ON or the [MANUAL] switch is

pressed, nothing is shown in the display until a Memory is recalled, or a

mode other than the Amp Mode is selected.

Enter the Amp Mode using one of the following methods.

• The Amp Mode is the default mode when the BBT500’s power is

switched ON.

• Press the [MANUAL] Switch to enter the Amp Mode.

• Press a Memory Switch [1] – [5] to recall a patch. Or, press and

hold a Memory Switch to save a patch to memory.

• In the Equalizer, Compressor, or Utility Mode, press the [FUNC-

TION] switch.

● How Knobs Function in the Amp Mode

The knob’s value is shown on the display

when the knob is turned.

Each control knob’s function in the Amp Mode is the same as de-

scribed in the “Sound Setting” section (→ pg. 10).

q INPUT LEVEL: Sets the Input Level

w SOUND TYPE: Selects the Sound Type (11 types)

e COMP: Compression Ratio (1.0 to ∞, 16 steps)

r GAIN: Pre-Amp Gain (0 to 10, 0.1 step)

t MASTER: Master Volume (0 to 10, 0.1 step)

y BASS: Bass Frequency (-15dB to +15dB, 0.2dB step)

u LOW MID: Low Mid Frequency (-15dB to +15dB, 0.2dB step)

i MIDDLE: Middle Frequency (-15dB to +15dB, 0.2dB step)

o HIGH MID: High mid Frequency (-15dB to +15dB, 0.2dB step)

!0 TREBLE: Treble Frequency (-15dB to +15dB, 0.2dB step)

!1 OUTPUT: Sets the output level

w e r t y u i o !0 !1

Compressor Mode

The Compressor Mode provides settings for the Compressor, Noise Gate,

and Blend Level for the effect loop.

To enter the Compressor Mode, press and hold the [FUNCTION] switch

until the knob functions are displayed in the upper row of the panel dis-

play above the knobs (the row above that used by the Equalizer Mode).

● How Knobs Function in the Compressor

Mode

q INPUT LEVEL: Sets the Input Level

w SOUND TYPE: No function.

e COMP (RATIO): Compression ratio (1.0 - ∞, 16 steps) *operates the same

as COMP in the Amp Mode.

r GAIN (THRSLD): Compressor threshold level (-54dB to 0dB, 1dB step)

Sets the signal level from which the compressor will activate. Compres-

sion is applied to signals that exceed this level.

t MASTER (ATTACK): Compressor attack time (0msec to 120msec, 1msec

step).

Sets the amount of time required for application of the compressor from

the time the signal exceeds the threshold. When a slow attack time is set,

the beginning of the attack will not be compressed.

y BASS (RELEASE): Compressor release time (5msec to 42.3 sec, 160

steps).

Sets the amount of time required for the compressor to switch off after the

signal goes below the threshold level. This smoothes gain changes to

keep the sound natural.

u LOW MID (C. GAIN): Compressor gain (0dB to 18dB, 0.1dB step)

This parameter works in conjunction with the compressor ratio setting

which is set with the e COMP (RATIO) control knob. In other words, gain

is automatically adjusted along with amount of compression applied to

the signal. If the Ratio = “1.0”, Gain = “0”. If the Ratio = “∞”, Gain = the

setting determined with the control knob.

i MIDDLE (KNEE): Compressor knee (Hd (Hard), 1, 2, 3, 4, 5)

Sets the depth of signal compression after the input signal exceeds the

threshold level. When set to Hd (hard), compression starts soon with the

ratio you have set. However, when set to 1-5, compression startup is

gradual, creating a more natural sound (soft knee compression).

o HIGH MID (N. GATE): Noise gate threshold level (OFF, -53dB to 0dB,

1dB step)

When the input signal’s level falls below this set level, the noise gate acti-

vates cutting off the signal.

!0 TREBLE (BLEND): Blend level between the effect loop’s RETURN signal

and the dry signal (the sound created in the BBT500H) (0% (Return 0%,

Dry 100%) to 100% (Return 100%, Dry 0%)).

!1 OUTPUT: Sets the output level

The knob’s value is shown on the

display when the knob is turned.

The function of each knob is

displayed here.

q w e r t y u i o !0 !1

The knob’s value is shown on the

display when the knob is turned.

The function of each knob is

displayed here.

q w e r t y u i o !0 !1

–

e PEQ F

t PEQ G

Frequency

Gain

r PEQ Q

0.1

Equalizer Mode

The Equalizer mode lets you make settings for the internal 1-Band Para-

metric Equalizer, and set the center frequency (or in the case of the

TREBLE control knob, its cutoff frequency) for each of the panel’s Tone

Controls (BASS – TREBLE) in the internal five-band equalizer.

To enter the Equalizer mode, press the [FUNCTION] switch. Knob func-

tions are displayed in the bottom row of the panel display above the

knobs.

● How Knobs Function in the Equalizer Mode

q INPUT LEVEL: Sets the Input Level

w SOUND TYPE: No function.

e COMP (PEQ F): Sets the center frequency of the 1-band parametric equal-

izer (20Hz to 20.0kHz, 255 steps)

r GAIN (PEQ Q): Sets the bandwidth of the 1-band parametric equalizer.

(0.1 to 20.0, 255 steps)

t MASTER (PEQ G): Sets the gain level of the 1-band parametric equal-

izer. (-15dB to +15dB, 0.2dB step)

y BASS (FREQ): Sets the center frequency of the BASS control knob. (20Hz

to 320Hz, 255 steps)

u LOW MID (FREQ): Sets the center frequency of the LOW MID control

knob. (80Hz to 1.28kHz, 255 steps)

i MIDDLE (FREQ): Sets the center frequency of the MIDDLE control knob.

(250Hz to 4.00kHz, 255 steps)

o HIGH MID (FREQ): Sets center frequency of the HIGH MID control knob.

(500Hz to 8.00kHz, 255 steps)

!0 TREBLE (FREQ): Sets the center/cutoff frequency of the TREBLE con-

trol knob. (1.25kHz to 20.0kHz, 255 steps)

!1 OUTPUT: Sets the output level

Detailed Parameter Settings

Utility Mode

The Utility Mode provides settings for the Crossover Filter and MIDI.

These settings are saved internally when you exit the Utility Mode and

kept even when the amplifier’s power is switched OFF.

● Entering the Utility Mode

To enter the Utility Mode, from any mode press and hold the [FUNC-

TION] switch for more than 3 seconds, until “utL” appears on the dis-

play.

INPUT

TUNER

OUT

SPEAKER

First amplifier (HPF 500Hz)

Second amplifier (LPF500Hz)

SPEAKER

Produces

higher

frequencies

above 500Hz

Produces

low

frequencies

up to 500Hz

Detailed Parameter Settings

* Set the INPUT LEVEL

to its minimum level

INPUT

Bass

* Set to “h50” with

the COMP control

knob

* Set to “L50” with the

COMP control knob

● How Knobs Function in the Utility Mode

In the Utility Mode, only the INPUT LEVEL, OUTPUT, and COMP knobs

function. All other knobs (SOUND TYPE, GAIN - TREBLE) have no func-

tion.

• INPUT LEVEL: Sets the Input Level

• OUTPUT: Sets the output level

• COMP: Sets the cut off frequency of the crossover filter

When the COMP knob is used (when setting the crossover filter), the

setting’s value is shown in the display. Other than that, only utL ap-

pears on the display.

Use the [MANUAL] switch and Memory Switches [1] through [5] to set

individual MIDI settings. (→ [MIDI Settings] pg. 15)

q w e

When the COMP knob is used (when

setting the crossover filter), the setting’s

value is shown in the display. Other than

that, only

utL appears on the display.

Individual MIDI

Settings

Crossover Filter

By connecting two BBT500Hs as shown in the illustration below, you

can create a bi-amplified system, where one amplifier is used to drive

high frequencies and a second amplifier drives low. This system uses

the amplifier’s onboard crossover filter (LPF or HPF) to determine the

range of frequencies that each amplifier will deliver.

● Setting the Crossover Filter

1 Press and hold the [FUNCTION] switch for more than three sec-

onds (until “utL” appears on the display) to enter the Utility

Mode.

2 Rotate the COMP knob to set the Crossover filter’s cutoff fre-

quency.

* Range of cutoff frequency

L10 (LPF 100Hz) to L00 (LPF 1000Hz), byP (Bypass),

h10 (HPF 100Hz) to h00 (HPF 1000Hz), 93 steps

When using a bi-amplified system, make sure

that the INPUT LEVEL control knob on the

second BBT500H is set to its minimum level.

Ex.) Operating a bi-amplified system in which the crossover fil-

ter on the first amplifier is set to h50 (HPF 500Hz) to pro-

duce high frequencies, and the crossover filter on the sec-

ond amplifier is set to L50 (LPF 500Hz) to produce low fre-

quencies.

STATUS

DATA/CTRL

BANK MSB/MAX

BANK LSB/MIN

TOGGLE ON-OFF

/NUMBER OF PGM

DEC

/NO

INC

/YES

MEMORY

EDIT

WRITE

/EXIT

±10

8.8.8.

Detailed Parameter Settings

MIDI Settings

The BBT500H is MIDI* compatible and equipped with MIDI IN and MIDI

OUT jacks.

* What is MIDI?

The acronym for Musical Instruments Digital Interface, MIDI is a world-

wide standard communication interface that allows MIDI compatible mu-

sical instruments, computers, and other MIDI devices to share musical

information and control one another regardless of instrument type or

maker.

With MIDI functions you can do things like select a patch from the

BBT500H’s memory using an external MIDI device like the MFC10

Yamaha MIDI Foot Controller, etc. You can also backup data by sending

the contents in the unit’s memory to a device that is capable of saving

MIDI data (Yamaha MDF3, etc.).

● Selecting a Patch with MIDI

1 Using a MIDI cable, connect the MIDI IN jack on the BBT500H to

the MIDI OUT jack on the external MIDI device.

* Use only a standard MIDI cable that is less than 15 meters in length. Use

of a longer cable can result in trouble such as abnormal operation, etc.

MIDI IN

MIDI OUT

External MIDI Device

MIDI Cable

BBT500H

Rear Panel

2 Set the MIDI receive channel on the BBT500H and the MIDI trans-

mit channel on the external device to the same MIDI channel.

(Default channel: 1)

* MIDI data can not be transmitted or received if the MIDI channels are

not properly matched.

2-1 Press and hold the [FUNCTION] switch for more than three

seconds (until “utL” appears on the display) to enter the

Utility Mode.

2-2 While holding the [MANUAL] switch, press Memory Switch [3].

The currently assigned MIDI receive channel appears on the

display (after a few seconds, the display will return to “utL”).

3 Create a Program Change Map*.

(Default

→→

→ Program Change No: Memory No = 1:1, 2:2, 3:3, 4:4,

5:5, 6:1, 7:2, 8:3 …)

* What is a Program Change Map?

A Program Change Map assigns a program change number (re-

ceived via MIDI) to a memory number. For example, when the

BBT500H receives “Program Change Number 1” from an external

MIDI device, it will recall memory number “3”. This is also called a

Program Change Table.

3-1 Press and hold the [FUNCTION] switch for more than 3 sec-

onds (until “utL” appears on the display) to enter the Utility

Mode.

3-2 While holding the [MANUAL] switch, press Memory Switch [1].

The currently assigned MIDI program change number appears

on the display (after a few seconds, the display will return to

“utL”).

3-3 Use Memory Switches [1] and [2] to set the program change

number (1-128) that is received by the BBT500H.

Use Memory Switch [2] to increase the value and Memory

Switch [1] to decrease the value.

3-4 While holding the [MANUAL] switch, press Memory Switch [2].

The memory number that will be recalled when the program

change number that was set in step 3-3, appears on the dis-

play. (After a few seconds, the display will return to “utL”).

3-5 Use Memory Switches [1] and [2] to set the memory number

(1-5) that corresponds to the program change number re-

ceived by the BBT500H.

Uses Memory Switch [2] to increase the value and Memory

Switch [1] to decrease the value.

3-6 If necessary, repeat steps 3-2 through 3-5.

3-7 Press the [FUNCTION] switch to enter the Amp Mode.

4 Now, when a program change number transmitted from an ex-

ternal MIDI device is received by the BBT500H, it will recall the

corresponding memory number that is set in the program

change map you just created will be recalled.

* Refer to the Owner’s Manual that came with your MIDI device on how

to receive or transmit program change data.

MIDI Receive Channel

Receive Program

Change Number

Memory Number

2-3 Use Memory Switches [1] and [2] to set the MIDI receive chan-

nel (1-16, ALL, oFF).

Use Memory Switch [2] to increase the value, and Memory

Switch [1] to decrease the value.

* “ALL” is set to Omni On. When “oFF” is set, MIDI data will

not be received.

Detailed Parameter Settings

● MIDI Merge Settings

If you want MIDI signals received by the BBT500H’s MIDI IN jack trans-

mitted without alteration to other MIDI devices connected to the BBT500H’s

MIDI OUT jack, set the MIDI Merge to “on”, if not, set it to “oFF”.

Press and hold the [FUNCTION] switch for more than three sec-

onds (until “utL” appears on the display) to enter the Utility Mode.

2 While holding the [MANUAL] switch, press Memory Switch [4].

The current MIDI Merge setting appears on the display (after a

few seconds the display will return to “utL”).

3 Use Memory Switches [1] and [2] to set MIDI Merge either “on”

(Memory Switch [2]) or “oFF” (Memory Switch [1]).

4 Press the [FUNCTION] switch to enter the Amp Mode.

● MIDI Bulk Out

You can use the MIDI Bulk Out operation to back up data saved in the

BBT500H (data in memory 1-5 and Utility Mode settings) to a device

that can save MIDI data (such as a Yamaha MDF3, etc.).

1 Using a MIDI cable, connect the MIDI OUT jack on the BBT500H

to the MIDI IN jack on an external MIDI device.

* Use only a standard MIDI cable that is less than 15 meters in length. Use

of a longer cable can result in trouble such as abnormal operation, etc.

2 Hold the [FUNCTION] switch for more than three seconds (un-

til “utL” appears on the display) to enter the Utility Mode.

3 While holding the [MANUAL] switch, press Memory Switch [5].

The type of data to be sent with the Bulk Out operation ap-

pears on the display (after a few seconds the display will re-

turn to “utL”).

MIDI IN

MIDI OUT

External MIDI Device

MIDI Cable

BBT500H

Rear Panel

4 Use Memory Switches [1] and [2] to set the type of data (1-5,

ALL) to be sent with the Bulk Out operation.

1-5 ...... Sends only the data from the selected memory number.

ALL ..... Sends all data in memory numbers 1-5 and Utility Mode

settings.

5 Press Memory Switch [5] to carry out the Bulk Out operation.

While the Bulk Out operation is in progress, all lamps on the

unit will light.

* The device number becomes the MIDI receive channel number (→ pg.

15). When the MIDI receive channel is set to “ALL” (Omni ON), the

channel is set to 1.

6 Press the [FUNCTION] switch to enter the Amp Mode.

● About MIDI Control Changes

You can control the overall volume of the BBT500H by con-

necting an external MIDI device’s MIDI OUT jack to the

BBT500H’s MIDI IN jack, and transmit Number 7 Control

Change Messages (Main Volume) to the BBT500H.

* With the exception of the Number 7 Control Change, the BBT500H

does not recognize any other MIDI Control Change messages.

* The Main Volume data will not change, even if a different memory

number is selected.

* When the POWER is switched ON, the Main Volume data is set

to its MAX value.

After the Main Volume data is changed, and the external MIDI device

is disconnected, the pre-amp’s volume level may not be sufficient. If

this case occurs, transmit a Control Change with a higher volume

setting again, or switch the POWER OFF and then back ON.

● About MIDI Bulk In

Using a MIDI cable, connect the MIDI IN jack on the BBT500H

to the MIDI OUT jack on an external MIDI device to return data

that has been stored on the external device, to the BBT500H’s

memory. This operation is referred to as MIDI Bulk In.

* The device number becomes the MIDI receive channel number

(→ pg. 15). When the MIDI receive channel is set to “ALL” (Omni

ON), the channel is set to 1. When set to “oFF” (OFF) data will

not be received.

* “Ld” appears on the display while receiving MIDI Bulk data.

● Sending/Receiving MIDI Data Between

Two BBT500Hs

The MIDI Bulk In or MIDI Bulk Out operations can be used to

copy memory or Utility Setup data in one BBT500H to another

BBT500H.

MIDI Merge Setting

Type of data to be sent with

the Bulk Out operation.

● Restoring the Factory Presets

This operation clears the contents

of the BBT500H’s memory 1-5

and restores all parameters to

their factory preset settings.

While holding the [MANUAL]

switch and Memory Switch [5],

switch the POWER switch ON.

Attaching the Rack Mount Adaptor

Attach the supplied rack mount adaptor lets you install the BBT500H in a stan-

dard 19-inch rack.

1. Remove the two screws A on the side of the device and remove the

carrying handle set.

2. Remove the two screws B on the side of the device.

3. Attach the supplied rack mount adaptor to the device using the three

supplied screws C.

* Never use any screws other than the supplied screws C. Using any other screws

can result in damage.

4. In the same manner, attach the other supplied rack mount adaptor to

the opposite side of the device.

5. Keep the leftover screws (A, B) in a safe place for future use.

* Make sure you don’t over-tighten the screws when reattaching the carrying handle

to the device. Doing so can result in damage to the carrying handle.

Air Flow

The device utilizes a forced air cooling system, which cools the interior of the unit by drawing air through the front intake by the fan, which

push the air out the back.

Intake Exhaust

Cooling fan

Front panel

Side view Rear view

Carrying Handle Set

Rack Mount Adaptor

(supplied)

Cable

Clamp Filter

● Attaching the Clamp Filter (For U.S. and Canadian models only)

To protect against electromagnetic waves, attach the supplied Clamp Filters to the cable connecting the bass guitar

to the amplifier’s INPUT jack, and the cables connecting the amplifier’s SPEAKER 1, 2 jacks to the speakers.

* When attaching the clamp filter, wrap the cable once around the clamp filter as close to the BBT500H unit as possible.

If an error occurs during operation, one of the following error message numbers will appear on the display.

E1: MIDI Receive Buffer Full

CAUSE: Too much MIDI data is being received by the BBT500H at one time.

SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks.

E2: Communication Error.

CAUSE: An abnormality is detected during MIDI communications.

SOLUTION: Check all connections, etc. and try again.

E3: Bulk Receive Check Sum Error.

CAUSE: The check sum does not match the received MIDI bulk data.

SOLUTION: Check all connections and data, and try again.

E4: MIDI Receive Data Abnormality.

CAUSE: An abnormality is detected in the received MIDI data.

SOLUTION: Check all connections and data, and try again.

Error Messages

Troubleshooting

• No Sound

→ Is the power cord properly connected to the device?

→ Is the volume turned up on the instrument connected to the INPUT jack?

→ Are the INPUT LEVEL, GAIN, MASTER, OUTPUT control knobs set to “0”?

→ Check the Effect Loop’s BLEND setting (Compressor Mode: TREBLE control knob). Unless an external effector is connected

to the device, raising the BLEND control will result in lowering the original sound. If the BLEND control is set to “100”, the

original sound will not be produced.

• Sound output is low

→ Is the volume turned up on the instrument connected to the INPUT jack?

→ Are the INPUT LEVEL, GAIN, MASTER, OUTPUT control knobs turned up?

→ Check the Effect Loop’s BLEND setting (Compressor Mode: TREBLE control knob). Unless an external effector is connected

to the device, raising the BLEND control will result in lowering the original sound. If the BLEND control is set to “100”, the

original sound will not be produced.

→ Check the Compressor setting. A low Threshold setting or a high Ratio setting will result in a lowered the output signal level.

Also, a long release setting or low Compressor Gain setting will result in a lowered output signal level.

Specifications

Power Amplifier Section

Class-D power amplifier circuitry

Output 500W/2Ω

Preamplifier Section

All digital signal processing

Sound Type: 11 Presets

5-Band Semi Parametric Tone Controls (Variable Frequencies)

Parametric Equalizer (PEQ, F, G, Q)

Effect Section

Compressor RATIO, THRSLD, ATTACK, RELEASE,

C. GAIN, KNEE

Limiter ON/OFF (SPEAKER, LINE OUT)

Noise Gate N. GATE

Crossover Filter LPF/HPF, Cutoff Frequency

Speaker Simulator ON/LINE/OFF (SPEAKER, LINE OUT)

Effect Loop

Monaural Send/Return, Level Switch (-20dB/+4dB), Effect

Blend Control

User Memory

5 User Memory (Sound Type, Amp Settings, Compressor,

Effect Blend)

MIDI Functions

Receive Program Change, Control Change, Bulk In

Transmit Program Change, Control Change, Bulk

Out, Merge Out

Controllers/Switches

Front Panel Control Knobs x 11, Push Switches x 7

Rear Panel Control Knob x1, Slide Switches x4

Displays

Push Switch LED x5

Sound Type LED x11

7-Segment LED x3 Digit

Input Level LED x2 (Green, Red)

Connections

INPUT: Standard Monaural Phone Jack

SPEAKER 1, 2: Standard Monaural Phone Jack

PHONES: Standard Stereo Phone Jack

LINE OUT (UNBALANCED OUT): Standard Monaural Phone Jack

LINE OUT (BALANCED OUT): XLR Jack

FX LOOP (SEND/RETURN): Standard Monaural Phone Jack

TUNER OUT: Standard Monaural Phone Jack

MIDI IN, MIDI OUT: 5-pin DIN jack

A/D Conversion

24 bit

D/A Conversion

24 bit

Sampling Frequency

48kHz

Input Level/Impedance

INPUT: -37dBm (thru)/1MΩ

FX LOOP RETURN: -20dBm/220kΩ, +4dBm/220kΩ

Output Level/Impedance

SPEAKER (BRIDGED OUT): 500W RMS/2Ω, 250W RMS/4Ω

LINE OUT (UNBALANCED OUT): +4dBm/10kΩ

LINE OUT (BALANCED OUT): +4dBm/600Ω

FX LOOP SEND: -20dBm/100kΩ, +4dBm/100kΩ

Power Requirements

U.S. and Canadian models : 120V, 60Hz

General model : 230V, 50-60Hz

Power Consumption

130W

Dimensions (W x H x D)

378 x 88 x 265 mm (14-7/8” x 3-7-16” x 10-7/16”)

Weight

U.S. and Canadian models : 4.7 kg (10 lbs. 6 oz)

General model : 5.2 kg (11 lbs. 7 oz)

Accessories

Power Cable

Rack Mount Adaptors X2

Rack Mount Adaptor Screws X6

Owner’s Manual (this booklet)

Clamp Filters X3 (U.S. and Canadian models only)

* Design and specifications may change without notice due to improvements.

YAMAHA [ Bass Amplifier ] Date:23-Dec-2003

Model BBT500H MIDI Implementation Chart Version : 1.0

+----------------------------------------------------------------------+

: : Transmitted : Recognized : Remarks :

: Function ... : : : :

:-------------------+----------------+----------------+----------------:

:Basic Default : x : 1 - 16, off : memorized :

:Channel Changed : x : 1 - 16, off : :

:-------------------+----------------+----------------+----------------:

: Default : x : 1,3 : memorized :

:Mode Messages : x : x : :

: Altered : ************** : x : :

:-------------------+----------------+----------------+----------------:

:Note : x : x : :

:Number : True voice: ************** : x : :

:-------------------+----------------+----------------+----------------:

:Velocity Note ON : x : x : :

: Note OFF : x : x : :

:-------------------+----------------+----------------+----------------:

:After Key's : x : x : :

:Touch Ch's : x : x : :

:-------------------+----------------+----------------+----------------:

:Pitch Bender : x : x : :

:-------------------+----------------+----------------+----------------:

: 0 - 6 : x : x : :

: 7 : x : o : Main Volume :

: 8 - 127 : x : x : :

: : : : :

: Control : : : :

: : : : :

: Change : : : :

: : : : :

:-------------------+----------------+----------------+----------------:

:Prog : x : o 0 - 127 : Program Change :

:Change : True # : ************** : : Number 1-128 :

:-------------------+----------------+----------------+----------------:

:System Exclusive : o : o : Bulk Dump :

:-------------------+----------------+----------------+----------------:

:System : Song Pos. : x : x : :

: : Song Sel. : x : x : :

:common : Tune : x : x : :

:-------------------+----------------+----------------+----------------:

:System :Clock : x : x : :

:Real Time :Commands: x : x : :

:-------------------+----------------+----------------+----------------:

:Aux :All Sound OFF: x : x : :

: :

Reset All Cntrls

: x : x : :

: :Local ON/OFF : x : x : :

: :All Notes OFF: x : x : :

:Mes- :Active Sense : o : x : :

:sages:Reset : x : x : :

:-------------------+----------------+----------------+----------------:

: :

+-------------------+----------------+----------------+----------------+

Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONO o : Yes

Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO x : No

Sayfa yükleniyor ...

Yamaha BBT500H El kitabı

Marka: Yamaha

Model: BBT500H

Kategori: Tamamlayıcı müzik ekipmanı

Tip: El kitabı

Bu kılavuz için de uygundur

BBT 500H

PDF İndir

rapor

Diğer dillerde

español: Yamaha BBT500H El manual del propietario
français: Yamaha BBT500H Le manuel du propriétaire
italiano: Yamaha BBT500H Manuale del proprietario
svenska: Yamaha BBT500H Bruksanvisning
čeština: Yamaha BBT500H Návod k obsluze
polski: Yamaha BBT500H Instrukcja obsługi
Deutsch: Yamaha BBT500H Bedienungsanleitung
português: Yamaha BBT500H Manual do proprietário
English: Yamaha BBT500H Owner's manual
dansk: Yamaha BBT500H Brugervejledning
русский: Yamaha BBT500H Инструкция по применению
Nederlands: Yamaha BBT500H de handleiding
română: Yamaha BBT500H Manualul proprietarului

Yamaha BBT500H El kitabı

Bu kılavuz için de uygundur

Yamaha BBT500H El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler