Hotpoint FMG 1023B EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi

Bu kılavuz için de uygundur

1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash option
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Troubleshooting, 11
Service, 12
WMF 923
Instructions for use
English,1
GB
Türkçe,13
TR
PT
Português,25
2
GB
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture
cabinets or anything
else.
2. If the floor is not perfectly level, compensate
for any unevenness by tightening or loosening
the adjustable front feet (see figure); the angle
of inclination, measured in relation to the
worktop, must not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a
wash cycle with detergent and no laundry,
using wash cycle number “Auto Clean” (see
“Cleaning the washing machine”).
Technical data
Model
WMF 923
Dimensions
width 59.5 cm
height 85 cm
depth 60.5 cm
Capacity
from 1 to 9 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 3
;
Cotton Standard 60°C.
programme 4
;
Cotton Standard 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cutting off the water and
electricity supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to
prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10%
the quantity specified
for lightly-soiled
garments) or special
additives to clean the
washing machine. We
recommend running a
cleaning programme every 40 wash cycles.
To start the programme press button A for 5
seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washing machine
(see figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
A
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery
and recycling of the materials they contain and reduce the
impact on human health and the environment. The crossed
out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected. Consumersshould contact
their local authority or retailer for information concerning
the correct disposal of their old appliance
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
TIMER
button
OPTION
button and
indicator light
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION button and indicator light: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION
button : to select the desired
wash intensity.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAY TIMER button: press to set a delayed start for
the selected wash cycle; the delay period appears on the
display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start
the wash cycle from the point at which it was interrupted,
press the button again.
CHILD LOCK button : to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the control
panel is locked (apart from the ON/OFF button). This
means it is possible to prevent wash cycles from being
modified accidentally, especially where there are children in
the home. To deactivate the control panel lock, press and
hold the button for approximately 2 seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
CLEANING
ACTION
button
CHILD
LOCK
button
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear; if the DELAY TIMER option has
been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened (wait approximately 3 minutes).
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 3 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
Select the wash programme: the cycle will be
automatically set to “Normal” as optimised for garments
with an average level of soil (this setting is not applicable
to the “Wool” cycle, which is automatically set to
Delicate”).
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment (4) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central
pivot (see figure pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened (wait approximately 3 minutes). Open the
door, unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Table of programmes and wash cycles
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual dam-
pness%
Energy con-
sumptionkWh
Total water lt
Cycle duration
Prewash
Wash
Bleach
Fabric
softener
1
Anti Stain
40° 1200
-
5 - - - 180’
2
Whites
60° 1200
-
5 - - - 180’
3
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200
(3)
9 53 1.19 57,5 195’
4
Cotton Standard 40° (2): lightly soiled resistant and delicate colours.
40° 1200 -
9 53 1.09 92 175’
5
Synthetics: heavily soiled resistant colours.
60° 800
4.5 46 1.03 60 115’
5
Synthetics (4): lightly soiled resistant colours.
40° 800
4.5 46 0.56 60 100’
6
Anti allergy
60° 1200 -
5 - - - 195’
7
Baby
40° 1000
5 - - - 145’
8
Wool: for wool, cashmere, etc.
40° 800 -
-
2 - - - 85’
9
Delicates
30° 0 -
-
1 - - - 80’
10
Fast Wash 60’: to refresh normal soiled garments quickly (not
suitable for wool, silk and clothes which require washing by hand).
60° 1200 -
-
3.5 53 0.84 44 60’
11
Cotton Standard 20°: lightly soiled resistant and delicate colours.
20° 1200 -
9 - - - 175’
12
Eco Cottons
Cold
Water
1200 -
-
9 53 0.23 68 80’
13
Eco Synthetics
Cold
Water
800 -
-
3 48 0.12 37 70’
14
Eco Fast 30’
Cold
Water
800 -
-
3 71 0.10 36 30’
Rinse
- 1200 - - -
9 - - - 36’
Spin and Pump out
- 1200 - - - - 9 - - - 16’
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 3 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 4 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C . The actual washing temperature may differ from the indicated value.
3) At 60 °C the “Prewash” function cannot be selected.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
4) Long wash cycle for synthetics: set wash cycle 5 with a temperature of 40°C.
Wash option
- If the selected option is not compatible with the set wash
cycle, the indicator light will flash and the option will not
be activated.
Prewash
If this function is selected, the pre-wash cycle will run; this
is useful for removing stubborn stains.
N.B.: Put the detergent in the relevant compartment.
10
GB
Baby: use the special wash cycle 7 to remove the soiling
typically caused by babies, while removing all traces of
detergent from nappies in order to prevent the delicate
skin of babies from suffering allergic reactions. The cycle
has been designed to reduce the amount of bacteria by
using a greater quantity of water and optimising the effect
of special disinfecting additives added to the detergent.
Wool: the wool wash cycle on this Hotpoint-Ariston
machine has been tested and approved by The Woolmark
Company for washing wool garments labelled as hand
washable provided that the garments are washed
according to the instructions on the garment label and
those issued by the manufacturer of this washing machine.
Hotpoint-Ariston is the first washing machine brand to be
approved by The Woolmark Company for Apparel Care-
Platinum for its washing performance and consumption of
energy and water. (M1127)
In UK, Eire, Hong Kong and India the Woolmark trade
mark is a Certification trade mark.
Delicates: use programme 9 to wash very delicate garments
with decorative features, such as diamantes and sequins.
To wash silk garments and curtains select the cycle 9 and
set the “Delicate” level from option .
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Eco cycles
The Eco Cycles assure energy saving by eliminating the
need of heating water and it’s an advantage both to your
energy bill and the environment! These innovative Eco
programmes (Eco Cottons 12, Eco Synthetics 13 and Eco
Fast 30’ 14) are available for various fabrics and different
quantity of garment; they have been designed to guarantee
a high cleaning action even at low temperature and can be
used for lightly to medium soiled loads. Eco Cycles give
the best results thanks to an intensified wash action, water
optimization and are carried out in the same average time
of a standard cycle. For the best washing results with Eco
Cycles we recommend the usage of a liquid detergent.
Cotton Standard 20° ideal for lightly soiled cotton
loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-
wash detergent (powder)
Before pouring in the
detergent, make sure that
extra compartment 4 has
been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertothe
weight of the laundry when dry:
see “Table of programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing
class that is higher than the standard class (A class). When
running the programme, do not mix garments of different
colours. We recommend the use of powder detergent.
Pre-treatment with special additives is recommended if
there are obstinate stains.
Whites: use this cycle 2 to wash white clothes. The
programme is designed to maintain the brightness of white
clothes over time. Use powder detergent for best results.
Anti allergy: use programme 6 to remove major allergens
such as pollen, mites, cat’s and dog’s hair.
M
AX
1
2
4
3
A
B
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The “option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display (e.g.:
F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomake
contact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
TR
13
Türkçe
TR
İçindekiler
Montaj, 14-15
Ambalajın çıkartılması ve aynı seviyeye getirilmesi
Su ve elektrik bağlantıları
İlk yıkama
Teknik bilgiler
Bakım ve onarım, 16
Su ve elektrik kesilmesi
Çamaşır makinesin temizlenmesi
Deterjan haznesinin temizlenmesi
Kapak ve hazne bakımı
Pompanın temizlenmesi
Su besleme hortumunun kontrol edilmesi
Önlem ve öneriler, 17
Genel güvenlik uyarıları
Atıkların tasye edilmesi
Çamaşır makinesinin tanıtımı, 18-19
Kumanda paneli
Ekran
Bir çamaşır çevriminin çalıştırılması, 20
Yıkama çevrim ve seçenekleri, 21
Programlar tablosu
Yıkama seçenekleri
Deterjan ve çamaşır, 22
Deterjan dağıtma çekmecesi
Çamaşırın hazırlanması
Özel yıkama çevrimleri
Sorun giderme, 23
Teknik Servis, 24
WMF 923
Kullanma talimatları
ÇAMAŞIR MAKİNESİ
14
TR
Montaj
! Bu kitapçığı gerektiği her an danışabilmeniz
için özenle saklayınız. Çamaşır makinesinin
satılması, devri veya nakli durumlarında da,
yeni sahibinin faydalanabilmesi için bu kılavuz
makineyle beraber saklanmalıdır.
! Talimatları dikkatlice okuyunuz; montaj, kullanım
ve güvenliğe ilişkin önemli bilgiler içermektedir.
! Taşıma ve Nakliye Sırasında Dikkat
Edilecek Konular
Taşıma ve nakliye sırasında ambalajın tama-
men kapalı olduğundan emin olunuz,
Taşıma ve nakliye işlemini orijinal ambalajı ile
yapınız.
Taşıma esnasında üründe hasar ve arıza
oluşmamasına, vurma, çarpma, düşürme vb.
dış etkenler nedeniyle ürünün zarar görme-
mesine dikkat ediniz.
Ambalajı zarar verebilecek nem, su, v.b. dış
etkenlere karşı koruyunuz.
Cihazın montajı yetkili servis tarafından
gerçekleştirilecektir.
Ambalajın çıkartılması ve aynı
seviyeye getirilmesi
Ambalajdan çıkartılması
1. Çamır makinesinin ambalajdan çıkarlması.
2. Çamır makinesinin taşıma esnasında hasar
görmem olduğunu kontrol ediniz. Hasar rmüş
ise monte etmeyiniz. Satıcıya başvurunuz.
3. Taşıma sırasında
arka tarafta bulunan
4 adet koruyucu vida
ve ara parçasıyla
birlikte buradaki lastiği
de çıkartınız (bakınız
şekil).
4. Delikleri ambalajda bulacağınız plastik
kapaklarla kapayınız.
5. m parçaları muhafaza ediniz: çamır
makinesinin nakli gerektiği takdirde takılmaları
gerekmektedir.
! Ambalajlar çocuk oyuncağı değildir.
Cihazın aynı seviyeye getirilmesi
1. çamaşır makinesini düz ve sert bir
zemine yerleştiriniz, duvar veya mobilyalara
dayamayınız.
2. Yer leş ti ril ec ek
zemin tam düz değilse
çamır makinesinin
vidalı ön ayaklarını
s ı k a r a k v e y a
gevşeterek dengeyi
sağlayınız (bkz. şekil);
eğim açısı, makinenin
üst tezgahına göre 2°
den fazla olmamalıdır.
Sağlıklı bir dengeleme, çamaşır makinesine
sağlam bir duruş kazandıracağı gibi, çalışma
esnasındaki sarsıntı, gürültü ve hareketlilikleri
de önleyecektir. Zeminde moket veya halı
olması halinde, ayarı makinenin altında
havalandırma olabilecek şekilde yapınız .
Su ve elektrik bağlantıları
Su besleme hortumunun takılması
1. Tedarik borusunu
3/4 gaz vidalý baðlantý
kullanarak bir soðuk
su musluðuna
baðlayýn (bkz. þekil).
Baðlantýyý yapmadan
önce, suyu berrak-
laþana kadar akýtýnýz.
2 . S u b e s l e m e
h o r t u m u n u a r k a
kısımının üst sağ
köşesinde bulunan
su girişine vidalayarak
makineye bağlayınız
(bkz. şekil).
3. Hortumda katlanma ve ezilme olmamasına
dikkat ediniz.
! Musluğun su basıncının Teknik Veriler
tabelasında belirtildiği gibi olması gerekir (bkz.
yan sayfa).
! Besleme hortumunun boyu yetersizse yetkili
bir satımağaza veya teknisyene başvurunuz.
! Kesinlikle daha önceden kullanılmış hortum
kullanmayınız.
! Makine ile birlikte verilen hortumlakullanınız.
TR
15
Tahliye hortumunun bağlanması
Tahliye hortumunu
bükmeden zeminden
65 ila 100 cm
yukarıda yer alan pis
su borusuna veya
duvar tahliyesine
bağlayın;
Buna alternatif
olarak, makine
ile birlikte verilen
pis su borusunu
musluğa (şekle
bakınız) bağlayarak
lavabo veya küvetin
kenarına yerleştirin.
Hortumun serbest
kalan ucu suya
daldırılmamalıdır.
! Hortum eklerinin kullanımı önermiyoruz; kesinlikle
gerekliyse ek hortum orijinal hortum ile aynı çapta
olmalı ve uzunluğu 150 cm. mamalır.
Elektrik bağlantıları
Cihazı elektrik prizine takmadan önce,
aşağıdakilerden emin olun:
Prizin topraklandıgından ve ilgili mevzuata
uygun oldugundan;
Prizin teknik veri tablosunda sterilmekte
olan maksimum cihaz elektrik yüküne
dayanıp dayanamayacagından (teknik veri
tablosuna bakiniz);
Güç kaynagı voltajının teknik veri tablosunda
sterilen degerlere uygun olup olmadigindan
(teknik veri tablosuna bakiniz);
Elektrik prizinin çamaşır makinesinin fişi
ile uyumlu olup olmadığından emin olun.
Muhafazalı değilse, priz veya şi değiştirin.
! Çamaşır makinesi kapalı alan olsa bile, evin
dışına yerleştirilmemelidir. Cihazın yağmur,
fırtına ve diğer hava koşullarına maruz
bırakılması son derece tehlikelidir.
! Çamaşır makinesi yerleştirildiğinde, elektrik
prizi kolay ulaşılabilir bir durumda olmalıdır.
65 - 100 cm
! Uzatma kablosu veya çoklu priz kullanmayın.
! Kablo bükülmemeli veya sıkıştırılmamalıdır.
! Güç kablosu ve si sadece yetkili
teknisyenler tarafından degistirilmelidir.
Uyarı! Bu standartlara uyulmaması
durumunda sirket sorumlu tutulamaz.
İlk yıkama
Ilk kullanimdan önce programlar tablosundaki
Kendi kendini temizleme” Programi
kullanarak çamasir olmadan deterjanla
bir yikama yapin (“Çamaşır makinesinin
temizlenmesi” bakınız).
Teknik bilgiler
Model WMF 923
Ölçüler
genişlik 59,5 cm
yükseklik 85 cm
derinlik 60.5 cm
Kapasite 1 - 9 kg
Elektrik
bağlantıları
makine üstünde takılı olan
teknik veriler plakasına
bakınız.
Su
bağlantıları
max. su basıncı
1 MPa (10 bar)
min. su basıncı
0,05 MPa (0,5 bar)
tambur kapasitesi 62 litre
Sıkma hızı
maksimum dakikada 1200
devire kadar
1061/2010 ve
1015/2010
sayılı dü-
zenleme
göre kontrol
programları
Program 3;
Pamuklu Standart 6C.
Program 4;
Pamuklu Standart 4C.
Bu makina aşağıda belirtilen
AB normlarına uygundur:
- 2004/108/CE (Elektroman-
yetik Uyum)
- 2012/19/EU (WEEE)
- 2006/95/CE (Alçak gerilim)
16
TR
Bakım ve onarım
Pompanın temizlenmesi
Çamaşır makinesinin pompası kendini
temizleyen bir özelliğe sahip olup, ayrıca
temizlik gerektirmez. Ancak, bazı küçük
cisimler (madeni para, düğme) pompanın alt
kısmındaki koruyucu bölmeye düşebilirler.
! Yıkama devresinin bitmiş olup olmadığını
kontrol ediniz ve şini çekiniz.
Pompa koruyucu bölgesine erişebilmek için:
1. çamaşır
makinesinin ön
kapama panelini, bir
tornavida vasıtasıyla
çıkartınız (bkz. şekil);
2. makine kapağını
saatin ters yönünde
çevirerek sökünüz
(bkz. şekil). bir miktar
su gelmesi normaldir;
3. içini dikkatlice temizleyiniz;
4. kapağı vidalayınız;
5. paneli takarken, tam yerleştirmeden evvel,
kancaların yuvalara gelip gelmediğini kontrol
ediniz.
Su besleme hortumunun kontrol
edilmesi
Su besleme hortumunu, en azından senede
bir defa kontrol ediniz. Yarık veya çatlaklar
varsa değiştiriniz: yıkama esnasındaki
yüksek basınçlar ani patlamalara yol
açabilirler.
! Kesinlikle daha önceden kullanılmış hortum
kullanmayınız.
Su ve elektrik kesilmesi
• Su musluğunu her yıkamadan sonra
kapatınız. Böylece çamaşır makinesinin su
tesisatının eskimesi engellenir, su kaçağı
tehlikesi ortadan kalkar.
• Bakım ve temizlik işlemleri esnasında
çamaşır makinesinin şini çekiniz.
Çamaşır makinesinin temizlenmesi
• Dış gövde ve plastik aksam ılık su ve
sabunla ıslatılmış bir bez vasıtasıyla
temizlenebilir. Çözücü ve aşındırıcı maddeler
kullanmayınız.
• Çamaşır makinesinde tambur boşken
çalıştırılması gereken “Kendi kendini
temizleme” programı bulunmaktadır.
Deterjan (az kirli çamaşırlar için tavsiye
edilen miktarın %10’u kadar) veya çamaşır
makinesinin temizliği için kullanılan özel katkı
maddeleri, yıkama programında yardımcı
olarak kullanılabilir. 40 yıkamada bir “Kendi
kendini temizleme” programını çalıştırmanız
önerilir.
Programı devreye
sokmak için, 5 san.
boyunca A tuşuna
basınız (bakınız
Şekil).
Program, otomatik
olarak başlayacak
ve yaklaşık 70
dakika sürecektir.
Devreyi durdurmak
için START/PAUSE
tuşuna basınız.
Deterjan haznesinin temizlenmesi
Hazneyi kaldırarak,
dışarıya doğru
çekmek suretiyle
çıkartınız (bkz. şekil).
Akar su altında
yıkayınız, bu
çekmecenin temizliği
sık sık yapılmalıdır.
Kapak ve hazne bakımı
Kötü kokuların oluşmasını engellemek için
kapağı daima aralık bırakınız.
1
2
A
TR
17
Önlem ve öneriler
! Çamaşır makinesi uluslararası güvenlik standartlarına
uygun olarak projelendirilmiş ve üretilmiştir. Bu uyarılar
güvenlik amaçlı olup dikkatlice okunmalıdır.
Genel güvenlik uyarıları
• Makine meskenlerde kullanılmak üzere tasarlanmış
olup profesyonel kullanım amaçlı değildir.
Bu cihaz, eğer gözetim altında bulunuyorlar
ise veya güvenli şekilde ve ilişkin tehlikeler
göz önünde bulundurularak, cihazın kullanı
hakkında uygun eğitim almışlar ise, 8 yaşından
k çocuklar ve ziksel, duyusal veya mental
kapasitelerden yoksun veya yetersiz tecrübe
ve bilgiye sahip kişiler tarafından kullanılabilir.
Çocuklar, cihaz ile oynamamalıdır. Bakım
ve temizlik işlemleri, denetimsiz çocuklar
tarafından gerçekleştirilmemelidir.
• Çamaşır makinesi yalnızca yetişkin kişiler tarafından
ve kullanma talimatına uygun olarak kullanılmalıdır.
• Cihaza ayaklarınız çıplakken yada elleriniz veya
ayaklarınız ıslak yada nemliyken dokunmayınız.
• Fişi prizden çekerken kablosundan değil şin
kendisinden tutarak çekiniz.
• Makine çalışırken deterjan haznesini açmayınız.
• Tahliye suyuna el sürmeyiniz, yüksek ısıda olabilir.
• Kapağı, hiçbir şekilde zorlamayınız: istenmedik
açılmalara karşı olan güvenlik mekanizması arıza
yapabilir.
• Arıza halinde onarmak amacıyla iç mekanizmaları
kurcalamayınız.
• Çocukların çalışır vaziyetteki makineye yaklaşmalarına
mani olunuz.
• Çalışma esnasında kapak ısınabilir.
• Taşınması gerektiğinde, bu işlemin, iki veya üç kişi
tarafından, azami dikkatle yapılması gerekir. Kesinlikle
tek başınıza yapmayınız, çünkü makine çok ağırdır.
• Çamaşırları yerleştirmeden evvel, sepetin boş
olduğundan emin olunuz.
Atıkların tasye edilmesi
• Ambalaj malzemelerinin tasye edilmesi: yerel yasalara
uyunuz, bu şekilde ambalajların geri dönüşümü
mümkün olur.
• Elektrik ve elektronik cihazların atıklarını değerlendirme
2012/19/EU (WEEE) sayılı Avrupa Konseyi direktinde;
beyaz eşyaların kentsel katı atık genel yöntemi ile
tasye edilmemesi öngörülmüştür. Kullanılmayan
cihazların, madde geri kazanım ve geri dönüşüm
oranını en yüksek seviyeye yükseltmek, çevre ve
insan sağlığına olası zararları engellemek için ayrı
ayrı toplanması gerekir. Tüm ürünlerin üzerinde; ayrı
toplama hükümlerini hatırlatmak amacıyla üstünde
çarpı işareti olan sepet sembolü verilmiştir.
Cihazların tasye edilmesi konusunda daha geniş bilgi
almak için cihaz sahiplerinin mevcut müşteri hizmetine
veya satış noktalarına başvurulması gerekir.
• Atık Elektrikli ve Elektronik Eşyaların (AEEE) Kontrolü
Yönetmeliği.
• AEEE Yönetmeliğine uygundur.
18
TR
Çamaşır makinesinin tanıtımı
Kumanda paneli
SİCAKLİK
AYARİ dügmesi
YIKAMA
ÇEVRİMİ
SEÇİCİ DÖNER
DÜĞME
Deterjan çekmecesi
ON/OFFdügmesi
DEVIR
AYARİ
düğmesi
START/PAUSE
düğmesi ve gösterge
lambası
EKRAN
ZAMAN
AYARİ
düğmesi
SEÇİM düğmeleri ve
gösterge lambaları
Deterjan çekmecesi: deterjan ve katkı maddelerini
dagıtmak için kullanılır (“Deterjan ve çamasır”’a bakınız).
ON/OFF düğmesi: makineyi açmak ya da kapatmak
için bu tuşa kısa süreli basınız. Yeşil renkte yanıp sönen
START/PAUSE uyarı lambası makinenin açık olduğunu
gösterir. Makineyi çalışır vaziyetteyken kapatmak için
tuşu daha uzun, yaklaşık 3 saniye, basılı tutmanız
gerekir;hafçe ya da yanlışlıkla basıldığında makine
kapanmaz. Makinenin çalışır vaziyetteyken kapatılması
devrede olan yıkama programını iptal eder.
PROGRAM SEÇME DÜGMESI
Istenilen yıkama çevrimini ayarlamak için kullanılır
(“Program ve yıkama çevrimi tablosu”’na bakınız).
SEÇİM düğmeleri ve gösterge lambaları: mevcut
seçenekleri seçmek için basın. Seçilen seçenek ile ilgili
gösterge ışığı açık kalacaktır.
TEMİZLEME ŞEKLİ
dügmesi: arzu edilen yıkama
yoğunluğunu seçmek için bu tuşa basınız
SİCAKLİK AYARİ düğmesi: sıcaklığı düsürmek veya
tamamen iptal etmek için basın; değer ekranda görünür.
DEVIR AYARİ dügmesi: Devir dügmesi: Sikma hizini
düsürmek veya tamamen iptal etmek için basin; deger
ekranda görünür.
ZAMAN AYARİ düğmesi: seçilen yıkama çevrimi için
bir gecikmeli çalıştırma ayarlamak için basın: gecikme
süresi ekranda belirir.
START/PAUSE düğmesi ve gösterge lambası: yeşil
lamba yavaşça yanıp sönünce istediğiniz yıkama
programını başlatmak için tuşa basınız. Yıkama programı
başladıktan sonra uyarı lambası yanık kalır. Seçilen
bir programın beklemeye alınması için aynı tuşa tekrar
basınız; uyarı lambası turuncu renkte yanıp sönecektir.
Sembol yanık değilse makine kapağı açılabilir
(yaklaþýk 3 dakika bekleyiniz). Yıkama programının
kaldığı yerden devam etmesi için aynı tuşa tekrar
basınız.
Ç
OCUK
KILIDI düğmesi : kontrol paneli etkin haline
getirmek için tuşu yaklaşık 2 saniye basılı tutmanız
gerekir. Sembol açık ise; kontrol panelinin kilitli
olduğunu gösterir (ON/OFF tuşu hariç). Böylece özellikle
çocuklarınız varsa programın yanlışlıkla değiştirilmesi
engellenir. kontrol panelini etkisiz haline getirmek için
tuşu yaklaşık 2 saniye basılı tutmanız gerekir.
Bekleme modu
Yeni enerji tasarrufu düzenlemeleri ile uyumlu bu çamaşır
makinesine herhangi bir faaliyet algılanmadığında 30
dakika içinde devreye sokulan otomatik bekleme sistemi
yerleştirilmiştir ON/OFFdüğmesine bir süre basın ve
makinenin tekrar çalışmasını bekleyin.
Ç
OCUK
KILIDI
düğmesi
TEMİZLEME
ŞEKLİ
düğmesi
TR
19
Ekran
Ekran makineyi programlarken çok yardımcı olur ve faydalı bilgiler sağlar.
Mevcut olan farklı programların süresi ve devre başladığı zaman aynı devrenin sonunda kalan süre görüntülenir; ZAMAN
AYARİ seçeneği ayarlanmışsa, seçili programın başlangıcı için geri sayım görünecektir.
Ilgili dügmeye basılması ayarlı yıkama çevrimi sırasında makine tarafından ulasılan maksimum sıkma hızını ve sıcaklık
degerlerini veya ayarlı yıkama çevrimi ile uyumlu ise en son seçilen degerleri görüntülemenize izin verir.
KAPI KİLİTLİ gösterge lambası:
Yanan sembol kapagın kilitli oldugunu gösterir. Makinenin hasar görmesini önlemek için, kapagı açmadan önce sembol
sönene kadar bekleyin.
Bir program çalisirken kapagi açmak için, START/PAUSE düğmesine basın, KAPAK KİLİTLİ sembolü kapalı ise,
kapak açılmayabilir (yaklaþýk 3 dakika bekleyiniz).
20
TR
Bir yıkama çevriminin çalıştırılması
1. MAKİNEYİ AÇIN. düğmesine basın, START/
PAUSE gösterge lambası yeşil renkte yavaş yavaş
yanıp sönecektir.
2. ÇAMAŞIRI YERLEŞTİRİN. Yan kapağı açın.
Aşağıdaki sayfada yer alan program ve yıkama
çevrimi tablosunda gösterilen maksimumk değerini
aşmamaya dikkat ederek, çamaşırı yerleştirin.
3. DETERJANI ÖLÇÜP AYIRIN. Deterjan çekmecesini
çekip çıkarın ve deterjanı “Deterjan ve çamasır”’da
tanımlandıgı gibi ilgili bölmelere dökün.
4. KAPAĞI KAPATIN.
5. YIKAMA ÇEVRIMINI SEÇIN. Istenilen yıkama
çevrimini seçmek için YIKAMA ÇEVRIMI SEÇICI
döner dügmeyi kullanın. Sıcaklık ve s hızı her yıkama
çevrimi için ayrı ayrı ayarlıdır, bu degerlerde degisiklik
yapılabilir. Çevrimresi ekranda gösterilecektir.
6. YIKAMA ÇEVRİMİNİ ÖZELLEŞTİRİN. İlgili düğmeleri
kullanın:
Sıcaklık ve/veya dönüş hızını değiştirin.
Makine, seçilen çevrimle uyumlu ise maksimum
sıcaklığı, seçilen çevrim için ayarlı dönüş hızı
değerlerini veya en son kullanılan ayarları otomatik
olarak görüntüler. Sıcaklık, soğuk Yıkama “OFF”
ayarına ulaşana kadar düğmesine basılarak
düşürülebilir. Dönüş hızı, tamamen devre dışı
bırakılana kadar düğmesine basılarak kademe
kademe azaltılabilir “OFF”. Bu düğmelere tekrar
basılırsa, maksimum değerler sıfırlanır.
! İstisna: 3 programı seçildiğinde sıcaklık derecesi
90°C ye kadar yükseltilebilir.
Gecikmeli çalıştırmanın ayarlanması.
Seçilen çevrim için gecikmeli başlatmayı ayarlamak
amacıyla, gerekli gecikme süresine ulaşana kadar
ilgili düğmeye tekrar tekrar basın. Bu seçenek
etkinleştirildiğinde, sembolü ekranda yanacaktır.
Gecikmeli başlatma ayarını kaldırmak için “OFF”
yazısı ekranda görünene kadar düğmeye basın.
Arzu edilen yıkama yoğunluğunu ayarlayınız.
opsiyonu, çamaşırların kirlilik derecesine göre ve
arzu edilen yıkama yoğunluğunda yıkama işlemini en
uygun hale getirmemize olanak tanır.
Yıkama programını seçiniz, yıkama devri aynı
derecede kirli olan çamaşırlar için en uygun olan
Normal” seviyede otomatik olarak ayarlanır,
(otomatik olarak “Delicate” seviyede ayarlanan
“Yünlüler” için geçerli olmayan ayar).
Çok kirli çamaşırlar için cihaz “Intensive” seviyeye
ulaşana kadar tuşuna basınız. Bu seviye, yıkama
programının başlangıç aşamasında daha çok su ve
daha fazla mekanik hareket kullanılması sayesinde
yüksek verimde yıkama performansı sağlamaktadır ve
en inatçı lekeleri bile ortadan kaldırmaya elverişlidir.
Çamaşır suyu ile ya da çamaşır suyu olmadan
kullanılabilir.
Eğer beyazlatma işlemi gerçekleştirilmek istenir ise
makine ile birlikte verilen ilave hazneyi 4, hazne 1
içine koyunuz. Çamaşır suyu dozajını ayarlarken
orta seviyede gösterilen “max” seviyeyi geçmeyiniz
(bakınız şekil syf. 22).
Az kirli çamaşırlar veya en hassas kumaşlar için
Delicate” seviyesine ulaşana kadar tuşuna
basınız. Hassas çamaşırlar için kusursuz yıkama
sonuçlarını garanti etmek için mekanik hareket
azaltılacaktır.
Çevrim ayarlarını değiştirin.
Seçimi etkinleştirmek için düğmeye basın, düğmeyle
ilgili gösterge lambası yanacaktır.
Seçimi devre dışı bırakmak için düğmeye tekrar
basın, gösterge lambası kapanacaktır.
! Seçilen seçenek ayarlı yıkama çevirimi ile uyumlu
degilse, gösterge lambası yanıp sönecek ve seçenek
etkinlestirilmeyecektir.
! Seçenekler önerilen yük değerini ve/veya çevrim
süresini etkileyebilir.
7. YIKAMA ÇEVRİMİNİ BAŞLATIN. START/PAUSE
düğmesine basın. İlgili gösterge lambası sürekli yanık
kalacak şekilde yeşil dönecek ve kapak kilitlenecektir
(KAPAK KİLİTLİ sembolü yanacaktır). Bir yıkama
çevrimini yürütüldüğü sırada değiştirmek için, START/
PAUSE düğmesini kullanarak çamaşır makinesini
duraklatın (START/PAUSE gösterge lambası yavaş
yavaş turuncu renkte yanıp sönecektir) ve sonra
istediğiniz çevrimi seçin ve START/PAUSE düğmesine
tekrar basın. Bir çevrim yürütülürken kapağı açmak için,
START/PAUSE düğmesine basın, KAPAK KİLİTLİ
sembolü kapalı ise, kapak açılmayabilir (yaklaþýk 3
dakika bekleyiniz). Yıkama çevrimini yarıda kesildiği
noktadan başlatmak için, START/PAUSE düğmesine
tekrar basın.
8. YIKAMA ÇEVRİMİNİN SONA ERMESİ. Bu durum
END” yazısı ekranda gösterilecektir, KAPAK KİLİTLİ
sembolü kapandığında, kapak açılabilir (yaklaþýk
3 dakika bekleyiniz). Kapağı açın, çamaşırı boşaltın ve
makineyi kapatın.
! Başlamış olan bir yıkama çevrimini iptal etmek
istiyorsanız, düğmesini basılı tutun. Çevrim
durdurulacak ve makine kapanacaktır.
1 / 1

Hotpoint FMG 1023B EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi
Bu kılavuz için de uygundur