Indesit XWDE 861480X WSSS EU Kullanici rehberi

1

GB

Washer-dryer

Instructions for use

! This symbol reminds you to read this instruction

manual.

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Opening the porthole door manually

Description of the washer-dryer, 6-7

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and options, 9-10

Table of wash cycles

Wash options

Push&Wash+Dry

Detergents and laundry, 11-12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

XWDE 861480

English,1

GB

NL

Nederlands,15

TR

Türkçe,29

RO

Română,43

FR DE

Français,57

Deutsch,71

2

GB

! This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If

it has been damaged, contact the retailer and

do not proceed any further with the installation

process.

3. Remove the 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on

the rear part of the

appliance (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washer-dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is

operating. If it is placed on carpet or a rug, adjust

the feet in such a way as to allow a sufficient

ventilation space underneath the washer-dryer.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it

to a cold water tap

using a ¾ gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washer-

dryer by screwing it

onto the corresponding

water inlet of the

appliance, which is

situated on the top

right-hand side of

the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

3

GB

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•thesocket isearthed and complies with all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see

opposite);

•thesocketiscompatiblewiththeplugofthe

washer-dryer. If this is not the case, replace

the socket or the plug.

! The washer-dryer must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washer-dryer has been installed, the

electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

65 - 100 cm

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle

“Auto Clean” (see “Cleaning the washer-dryer”).

Technical data

Model

XWDE 861480

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 8 kg for wash

programme

from 1 to 6 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 58 litres

Spin speed

up to 1400 rotations per

minute

Energy ra-

ted

programmes

according to

regulation

EN 50229

wash: programme 8; tem-

perature 60°C; using a load

of 8 kg.

drying: the smaller load

(2kg) must be dried by se-

lecting the “ ” dryness le-

vel. The load must consist of

3 sheets, 2 pillowcases and

1 hand towel; the remainder

of the load must be dried by

selecting the “ ” dryness

level.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU - WEEE

4

GB

Care and maintenance

Cleaning the pump

The washer-dryer is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front

of the machine by

first pressing it in

the centre and then

pushing downwards

on both sides until

you can remove it

(see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system inside

the washer-dryer and help to prevent leaks.

•Unplugthewasher-dryerwhencleaningitand

during all maintenance work.

Cleaning the washer-dryer

•Theouterpartsandrubbercomponents

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

•Thewasher-dryerhasa“AutoClean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washer-dryer. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for the door and drum of your

appliance

•Alwaysleavetheportholedoorajarinorderto

prevent unpleasant odours from forming.

2

1

2

3

A

B

5

GB

Precautions and tips

! This washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and must

therefore be read carefully.

General safety

•Thisappliancewasdesignedfordomesticuseonly.

•Thisappliancecanbeusedbychildrenaged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not

be made by children without supervision.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes

and wax removers should be washed in hot

water with an extra amount of detergent before

being dried in the tumble dryer.

– Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried in

the tumble dryer.

– Fabric softeners, or similar products, should

be used as specified by the fabric softener

instructions.

– The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that the

items are left at a temperature that ensures that

the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items are

quickly removed and spread out so that the

heat is dissipated.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunpluggingthe

appliance from the electricity socket. Hold the plug and pull.

•Do notopen the detergentdispenserdrawer while the

machine is in operation.

•Donottouchthedrainedwaterasitmayreachextremely

high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethesafety

lock mechanism designed to prevent accidental opening.

•If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupoftwo

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

•Beforeloadinglaundryintothewasher-dryer,makesure

the drum is empty.

• Duringthedryingphase,thedoortendstogetquitehot.

• Donotusetheappliancetodryclothesthat

have been washed with flammable solvents

(e.g. trichlorethylene).

• Donotusetheappliancetodryfoamrubber

or similar elastomers.

• Makesurethatthewatertapisturnedonduring 

the drying cycles.

• Childrenoflessthan3yearsshouldbekept

away from the appliance unless continuou-

sly supervised.

• Remove all objects frompockets such as

lighters and matches.

Disposal

•Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The EuropeanDirective2012/19/EU (WEEE) onWaste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise

the recovery and recycling of the materials they contain and

reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose of

the appliance it must be separately collected. Consumers

should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower than

the door opening; if it is not, remove excess water using the

drain hose, collecting it in a bucket as indicated in the figure.

3. remove the cover panel on the lower front part of the

washer-dryer (see figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

20

1

2

3

6

GB

Description of the washer-dryer

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button

and indicator light

DELAYED

START

button

OPTION

buttons

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine

is switched on. To switch off the washer-dryer during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

PUSH&WASH+DRY button: (see “Wash cycles and

options”).

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of wash cycles”).

OPTION buttons: press to select the available options.

The indicator light corresponding to the selected option will

remain lit.

TEMPERATURE button: press to reduce or

completely exclude the temperature; the value appears on

the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DELAYED START button: press to set a delayed

start for the selected wash cycle; the delay period appears

on the display.

DRYING button : press to decrease or exclude drying;

the selected drying level or time will appear on the display

(see “How to run a wash cycle or a drying cycle”).

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an amber colour. If the symbol is not illuminated, the

door may be opened. To start the wash cycle from the

point at which it was interrupted, press the button again.

Standby mode

This washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

DISPLAY

PUSH&WASH+DRY

button

DRYING

button

7

GB

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view either the maximum spin speed, temperature and drying time values

attained by the machine during the set wash cycle, or the values selected most recently (if compatible with the set wash

cycle).

The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of

10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon

will then switch off approximately 1 minute after the final amount of time remaining has appeared.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin/Drain

Drying

The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.

There are three levels in section C concerning the washing options.

Section D includes the icons related to the three different drying levels as well as the icon , which lights up when a timed

drying option is set.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

Display

B

D

A

C

8

GB

How to run a wash cycle or a

drying cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH&WASH+DRY” button to start the

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the 8 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Cupboard : suitable for laundry which can be put

back in a cupboard without being ironed.

Hanger : ideal for clothes which do not need to be

dried fully.

Iron : suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

B - Based on a set time period: between 210 and 30 minutes

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table of wash cycles), perform the wash cycle, and when

the cycle is complete, divide the garments into groups

and put some of them back in the drum. At this point,

follow the instructions provided for a “Drying only” cycle.

Repeat this procedure for the remainder of the load.

Note: a cooling-down period is always added to the end

of each drying cycle.

Drying only

Press button to perform the drying-only cycle.

After selecting the desired cycle (compatible with the type

of garments), press button to exclude the washing

phase and start the drying phase at the maximum level

for the selected cycle. The drying level or time may be set

and changed by pressing the drying button .

(Not compatible with cycles 13 and 14).

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Modify the cycle settings.

• Pressthebuttontoenabletheoption;theindicator

light corresponding to the button will switch on.

• Pressthebuttonagaintodisabletheoption;the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/PAUSE

button. The corresponding indicator light will turn green,

remaining lit in a fixed manner, and the door will be locked

(the DOOR LOCKED symbol will be lit). To change a

wash cycle while it is in progress, pause the washer-

dryer using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an amber colour); then

select the desired cycle and press the START/PAUSE

button again. To open the door while a cycle is in progress,

press the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press the

START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

9

GB

Wash cycles and options

Table of wash cycles

Wash options

- If the selected option is not compatible with the set wash

cycle, the indicator light will flash and the option will not

be activated.

Stain removal

Thisoptionallowsforselectingthetypeofdirtsoasto

optimally adjust the cycle for removing the stains. The

following types of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages,

for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of

selected dirt.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: select wash cycle 8 with a temperature of 60°C.

2) Long wash cycle for cottons: select wash cycle 10 with a temperature of 40.

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Maximum load

for drying (Kg)

Detergents

Maximum load

for washing (Kg)

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

The duration of the wash cycles can be checked on the display.

1

Sport

30° 600



4

-

 

-

4

2

Dark

30° 800



3

-

 

-

5

3

Anti-odour (Cotton) 60° 1000



3,5

-

 

-

3,5

3

Anti-odour (Synthetic) 40° 1000



3,5

-

 

-

3,5

4

Delicate

30° 0



1

-

 

-

1

5

Wool: for wool, cashmere, etc. 40° 800



2

-

 

-

2

6

Rapid 30’

30° 800



3,5

-

 

-

3,5

Standard

7

Cottons with Pre-wash: extremely soiled whites. 90° 1400



6

  

-

8

Cotton Standard 60° (1-2): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1400



6

-

 

-

8

9

Synthetic: heavily soiled resistant colours. 60° 1000



4

-

 

-

4,5

10

Coloured

40° 1400



6

-

 

-

8

11

Eco Cotton 20°: lightly soiled whites and delicate colours. 20° 1400



6

-

 

-

8

12

Eco Synthetic

20° 1000



6

-

 

-

8

Automatic

13

Wash&Dry 45’

30° 1400



1

-

 

-

1

14

AirFresh

- -



1,5

- - - -

-

Partials

Rinse/Bleach - 1400



6

- -

 

8

Spin + Drain - 1400



6

- - - -

8

Drain only * - OFF

- - - - - -

8

10

GB

Push&Wash+Dry

This function makes it possible to start an automatic wash and drying cycle either when the machine is off without having to

press the ON/OFF button in advance, or after switching on the machine without having activated any button and/or selector

(otherwise the Push&Wash+Dry function will be deactivated). To start the Push&Wash+Dry cycle press and hold the button

for 2 seconds. The indicator lights up to show that the cycle has started. The wash and drying cycle is ideal for cotton or

synthetic fabrics, as it washes them at a temperature of 30° and a maximum spin speed of 1000 rpm. During the drying

cycle the maximum temperature is 60°C. At the end of the cycle the residual humidity will be the same as for the “ ” level.

Max recommended load 3 kg.

The time displayed is the maximum time allowed by the Push&Wash+Dry cycle. If the load is lower than the maximum load

or most garment are made of synthetic materials, the actual time of the cycle will be shorter.

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and/or additives.

3. Start the cycle by pressing and holding the Push&Wash+Dry button for 2 seconds. The relevant indicator light will turn

green and the door will lock (the DOOR LOCKED symbol is lit).

NB: starting the cycle through the Push&Wash+Dry button activates an automatic non-customisable wash and drying cycle

recommended for cotton and synthetic fabrics.

4. The automatic cycle can be used only for washing, excluding the drying phase. Press the Push&Wash+Dry button and

then the drying button : the drying icon of the “ ” level will switch off. Maximum load for washing-only is 4 kg. The cycle

cannot be customised further.

To open the door while an automatic cycle is under way, press the START/PAUSE button. If the DOOR LOCKED symbol is

off, the door may be opened only during the washing phase. Press the START/PAUSE button again to restart the wash cycle

from the point at which it was interrupted.

5. At the end of the wash cycle the word END will light up.

11

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition

into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into

compartment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Emptyallgarmentpocketsandcheckthebuttons.

• Do not exceed the valueslisted in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Special wash cycles

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use programme 2 to wash dark-coloured garments.

This programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

When you select the drying function, at the end of the

washing cycle the machine will automatically perform a

delicate drying cycle that preserves the colours of the

garments. The display will show the level “ ”.

Max. load: 3 kg.

Anti-odour: use programme 3 for washing garments

with bad odours (e.g. smoke, sweat, fried food). The

programme is designed to remove bad odours while

preserving the fabric fibres. Synthetics fabrics or mixed

loads should be washed at 40°, and resistant cotton

fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

When selecting an exclusively time-based drying function,

a drying cycle is performed at the end of the wash cycle

that is particularly delicate, thanks to light handling and

appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Wool: the wool wash programme of this machine has

been tested and approved by The Woolmark Company

for the washing of wool containing garments labelled as

“hand wash” provided that the garments are washed

according to the instructions on the garment label and

those issued by the manufacturer of this washer-dryer.

(M1127)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Rapid 30’ (programme 6) this programme is designed to

wash lightly soiled garments at 30° (excluding wool and

silk) with a 3 kg maximum load in a short time: it only lasts

30 minutes and allows for saving time and energy

Coloured: use this programme 10 to wash bright

coloured clothes. The programme is designed to maintain

bright colours over time.

Eco Cotton 20° (programme 11) ideal for lightly soiled

cotton loads. The effective performance levels achieved at

cold temperatures, which are comparable to washing at

40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

12

GB

Eco Synthetic (programme 12) ideal for mixed loads

(cotton and synthetics) with a normal soil level. The

effective performance levels achieved at cold temperatures

are guaranteed by a mechanical action which operates at

varying speed, across set average intervals.

Wash&Dry 45’ select programme

13

for washing and

drying lightly soiled garments (Cotton and Synthetic) in a

short time. This cycle may be used to wash and dry a

laundry load of up to 1 kg in just 45 minutes. To achieve

optimum results, use liquid detergent and pre-treat cuffs,

collars and stains.

AirFresh (programme

14

) ideal cycle to refresh garments

and remove bad odours, in particular smoke, from cotton

and synthetic items in 30’ (max 1.5kg) without the washing

phase.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washer-dryer performs the

distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

13

GB

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make

sure that the problem cannot be solved easily using the following list.

Problem:

The washer-dryer does not switch

on.

The wash cycle does not start.

The washer-dryer does not fill

with water (the text “H2O” on the

display).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

The washer-dryer does not dry.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.

•Thereisnopowerinthehouse.

•Thewasher-dryerdoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

•Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining

process to be enabled manually.

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•Thewasher-dryerisnotlevel(see “Installation”).

•Thewasher-dryeristrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for

washer-dryers” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• AfterswitchingonthemachineacontrolotherthanPush&Wash+Drywas 

activated. Switch the machine off and press the Push&Wash+Dry button.

• Theapplianceisnotpluggedintothesocket,ornotenoughtomakecontact.

• Therehasbeenapowerfailure.

• Theappliancedoorisnotshutproperly.

• ADELAYTIMERhasbeenset.

• DRYINGisintheOFF position.

14

GB

Service

Before contacting the Technical Assistance Service:

• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).

• Restartthewashcycletocheckwhethertheproblemhasbeensolved.

• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of

the appliance by opening the door.

15

NL

Nederlands

NL

WASDROOGMACHINE

! Dit symbool herinnert u eraan om deze gebrui-

kshandleiding te lezen.

Inhoud

Installatie, 16-17

Uitpakken en waterpas zetten

Hydraulische en elektrische aansluitingen

Eerste wascyclus

Technische gegevens

Onderhoud en verzorging, 18

Afsluiten van water en stroom

Reinigen van de Wasdroogmachine

Reinigen van het wasmiddelbakje

Onderhoud van deur en trommel

Reinigen van de pomp

Controle van de buis van de watertoevoer

Voorzorgsmaatregelen en advies, 19

Algemene veiligheid

Afvalverwijdering

Handmatige opening van het deurtje

Beschrijving van de Wasdroogmachine, 20-21

Bedieningspaneel

Display

Het uitvoeren van een was- of droogcyclus, 22

Programma’s en opties, 23-24

Programmatabel

Wasopties

Push&Wash+Dry

Wasmiddelen en wasgoed, 25-26

Wasmiddelbakje

Bleekcyclus

Voorbereiden van het wasgoed

Speciale programma’s

Balanceersysteem van de lading

Storingen en oplossingen, 27

Service, 28

XWDE 861480

Gebruiksaanwijzing

16

NL

Een correcte nivellering geeft de machine

stabiliteit en voorkomt trillingen, lawaai en het

zich verplaatsen van de automaat tijdens de

werking. In het geval van vloerbedekking of

een tapijt regelt u de stelvoetjes zodanig dat

onder de wasmachine genoeg plaats is voor

ventilatie.

Hydraulische en elektrische

aansluitingen

Aansluiting van de watertoevoerbuis

1. Sluit de toevoerbuis

aan op de

koudwaterkraan met

een mondstuk met

schroefdraad van 3/4

gas (zie afbeelding).

Voordat u de

Wasdroogmachine

aansluit moet u het water

laten lopen totdat het

helder is.

2. Verbind de

watertoevoerbuis aan

de Wasdroogmachine

door hem op

de betreffende

watertoevoer te

schroeven, rechtsboven

aan de achterkant (zie

afbeelding).

3. Let erop dat er geen knellingen of kronkels

in de buis zijn.

! De waterdruk van de kraan moet zich

binnen de waarden van de tabel Technische

Gegevens bevinden (zie bladzijde hiernaast).

! Als de toevoerbuis niet lang genoeg is moet

u zich wenden tot een gespecialiseerde winkel

of een bevoegde installateur.

! Gebruik nooit tweedehands buizen.

! Gebruik de buizen die bij het apparaat

worden geleverd.

Installatie

! Het is belangrijk deze handleiding te bewaren

voor latere raadpleging. In het geval u het

apparaat verkoopt, of u verhuist, moet het

boekje bij de Wasdroogmachine blijven

zodat de nieuwe gebruiker de functies en

betreffende raadgevingen kan doornemen.

! Lees de instructies aandachtig door: u vindt

er belangrijke informatie betreffende installatie,

gebruik en veiligheid.

Uitpakken en waterpas zetten

Uitpakken

1. De Wasdroogmachine uitpakken.

2. Controleer of de Wasdroogmachine geen

schade heeft geleden gedurende het vervoer.

Indien dit wel het geval is moet hij niet worden

aangesloten en moet u contact opnemen met

de handelaar.

3. Verwijder de 4

schroeven die het

apparaat beschermen

tijdens het vervoer

en de rubberen ring

met bijbehorende

afstandsleider die zich

aan de achterkant

bevinden (zie

afbeelding).

4. Sluit de openingen af met de bijgeleverde

plastic doppen.

5. Bewaar alle onderdelen: mocht de

Wasdroogmachine ooit worden vervoerd, dan

moeten deze weer worden aangebracht.

! Het verpakkingsmateriaal is geen speelgoed

voor kinderen.

Waterpas zetten

1. Installeer de Wasdroogmachine op een rechte

en stevige vloer en laat hem niet steunen tegen

een muur, meubel of dergelijke.

2. Als de vloer niet

volledig horizontaal

is kunt u de

onregelmatigheid

opheffen door de

stelvoetjes aan de

voorkant losser of

vaster te schroeven

(zie afbeelding);

de inclinatiehoek,

gemeten ten

opzichte van het werkvlak, mag de 2° niet

overschrijden.

17

NL

Aansluiting van de afvoerbuis

Verbind de buis,

zonder hem te

buigen, aan een

afvoerleiding of aan

een afvoer in de muur

tussen de 65 en 100

cm van de grond af;

of hang hem aan de

rand van een wasbak

of badkuip, en bind

de bijgeleverde

steun aan de kraan

(zie afbeelding).

Het uiteinde van de

afvoerslang mag niet

onder water hangen.

! Gebruik nooit verlengstukken voor de

buis; indien dit niet te vermijden is moet het

verlengstuk dezelfde doorsnede hebben als de

oorspronkelijke buis en mag hij niet langer zijn

dan 150 cm.

Elektrische aansluiting

Voordat u de stekker in het stopcontact steekt

moet u zich ervan verzekeren dat:

• hetstopcontactgeaardisenvoldoetaande

geldende normen;

• hetstopcontacthetmaximumvermogen

van de Wasdroogmachine kan dragen, zoals

aangegeven in de tabel Technische Gegevens

(zie hiernaast);

• despanningzichbevindttussende

waarden die zijn aangegeven in de tabel

Technische Gegevens (zie hiernaast);

• decontactdoosgeschiktisvoordestekker

van de Wasdroogmachine. Indien dit niet

zo is moet de stekker of het stopcontact

vervangen worden.

! De machine mag alleen binnenshuis op een

vorstvrije en droge plek worden geïnstalleerd

om elektronische schade door bevriezing of

condensatie te voorkomen.

! Als de Wasdroogmachine is geïnstalleerd moet

het stopcontact gemakkelijk te bereiken zijn.

! Gebruik geen verlengsnoeren of dubbelstekkers.

! Het snoer mag niet gebogen of

samengedrukt worden.

! De voedingskabel mag alleen door een

bevoegde installateur worden vervangen.

65 - 100 cm

Belangrijk! De fabrikant kan niet aansprakelijk

worden gesteld wanneer deze normen niet

worden nageleefd.

Eerste wascyclus

Na de installatie en voor u de Wasdroog-

machine in gebruik neemt, dient u een

wascyclus uit te voeren met wasmiddel

maar zonder wasgoed, op het programma

“WASMACHINE REINIGEN” (zie “Reinigen van

de Wasdroogmachine”).

Technische gegevens

Model

XWDE 861480

Afmetingen

breedte cm 59,5

hoogte cm 85

diepte cm 54

Vermogen

van 1 tot 8 kg voor het wa-

ssen;

van 1 tot 6 kg voor het drogen;

Elektrische

aansluitin-

gen

zie het typeplaatje met de tech-

nische eigenschappen dat op

het apparaat is bevestigd

Aansluiting

waterleiding

max.druk1MPa(10bar)

min. druk 0,05 MPa (0,5 bar)

Inhoud trommel 58 liters

Snelheid

centrifuge

tot 1400 toeren per minuu

Controle-

program-

ma’s vol-

gens de

reglement

EN 50229

wassen: programma 8 ;

temperatuur 60°C; uitgevo-

erd met 8 kg lading.

drogen: het drogen van de

kleinste lading (2kg) moet

worden uitgevoerd door het

selecteren van het droogni-

veau “ ”. De lading moet

bestaan uit 3 lakens, 2 kus-

sensloop en 1 handdoeken;

het drogen van het over-

gebleven wasgoed moet

worden uitgevoerd door het

droogniveau “ ” te selec-

teren.

Deze apparatuur voldoet

aan de volgende CE voor-

schriften:

- 2004/108/CE (Elektroma-

gnetische compatiabiliteit)

- 2012/19/EU - WEEE

- 2006/95/CE (Laagspanning)

18

NL

Reinigen van de pomp

De Wasdroogmachine is voorzien van

een zelfreinigende pomp en hoeft dus niet

te worden onderhouden. Het kan echter

gebeuren dat kleine voorwerpen (muntjes,

knopen) in het voorvakje dat de pomp

beschermt en zich aan de onderkant ervan

bevindt, terechtkomen.

! Verzeker u ervan dat de wascyclus beëindigd

is en haal de stekker uit het stopcontact.

Toegang tot het voorvakje:

1. verwijder het

afdekpaneel aan

de voorzijde van de

Wasdroogmachine

door er op het

midden op te

drukken. Duw

beide zijkanten naar

beneden toe en

verwijder het paneel

(zie afbeeldingen).

2. draai het deksel

eraf, tegen de klok in

(zie afbeelding): het

is normaal dat er een

beetje water uit komt;

3. maak de binnenkant goed schoon;

4. schroef het deksel er weer op;

5. monteer het paneel weer, met de haakjes

goed bevestigd in de juiste openingen, voordat

u het paneel tegen de machine aandrukt.

Controleren van de buis van de

watertoevoer

Controleer minstens eenmaal per jaar de

slang van de watertoevoer. Als er barstjes of

scheuren in zitten moet hij vervangen worden:

gedurende het wassen kan de hoge waterdruk

onverwachts breuken veroorzaken.

! Gebruik nooit tweedehands buizen.

Onderhoud en verzorging

Afsluiten van water en stroom

• Sluitnaiederewasbeurtdekraan

af. Hiermee beperkt u slijtage van de

waterinstallatie van de wasmachine en

voorkomt u lekkage.

• Sluitaltijdeerstdestroomafvoordatude

Wasdroogmachine gaat schoonmaken en

gedurende onderhoudswerkzaamheden.

Reinigen van de

Wasdroogmachine

•Debuitenkantenderubberenonderdelen

kunnen met een spons en een lauw sopje

worden schoongemaakt. Gebruik nooit

schuurmiddelen of oplosmiddelen.

•DeWasdroogmachinebeschiktovereen

programma “WASMACHINE REINIGEN”

voor het reinigen van de binnenkant van de

automaat. Dit moet worden uitgevoerd als de

automaat volledig leeg is.

Het wasmiddel (circa 10% van de hoeveelheid

die wordt aanbevolen voor een niet zo vuile

was) of de speciale reinigingsmiddelen voor

wasautomaten kunnen worden gebruikt als

hulpmiddelen tijdens dit wasprogramma. We

raden u aan dit reinigingsprogramma elke 40

wascycli uit te voeren.

Om dit programma

te activeren drukt u

tegelijkertijd 5 sec. op

de toetsen A en B (zie

afb.).Het programma

start automatisch en

heeft een duur van circa

70 minuten. Om de

cyclus te beëindigen

drukt u op de toets

START/PAUSE.

Reinigen van het wasmiddelbakje

Verwijder het laadje

door op het hendeltje

(1) te drukken en het

naar voren te trekken

(2) (zie afbeelding).

Was het onder

stromend water. Dit

moet u regelmatig

doen.

Onderhoud van deur en trommel

•Laatdedeuraltijdopeenkierstaanomnare

luchtjes te vermijden.

2

1

2

3

A

B

19

NL

Voorzorgsmaatregelen

en advies

kledingstukken met rubberen opschriften e.d.

• Controleerdatgedurendehetdrogendewaterkraanopenis.

•Kinderenvan3jaarofmindermogennietdichtbij

de droger komen, tenzij onder constant toezicht.

•Verwijderallevoorwerpen,zoalsaanstekersen

lucifers, uit de zakken.

Afvalverwijdering

• Hetverwijderenvanhetverpakkingsmateriaal:

houdt u aan de plaatselijke normen zodat het materiaal

hergebruikt kan worden.

• De Europese richtlijn 2012/19/EU (WEEE), betreffende

afgedankte elektrische en elektronische apparatuur, voorziet

dat huishoudelijke apparatuur niet met het normale afval mag

worden meegegeven. De afgedankte apparatuur moet apart

worden opgehaald om het wedergebruik van materialen

waarvan hij is gemaakt te optimaliseren en om potentiële

schade aan de gezondheid en het milieu te voorkomen. Het

symbool van de afvalemmer met een kruis staat op elk product,

om aan te geven dat het apart moet worden weggegooid. Voor

verdere informatie betreffende het correcte verwijderen van

huishoudelijke apparatuur kunnen de gebruikers zich wenden

tot de gemeentelijke reinigingsdienst of de verkoper.

Handmatige opening van het deurtje

Mocht er in het huis geen stroom aanwezig zijn en u wilt het

deurtje openen om de was op te hangen, dan dient u het

volgende te doen:

1. haal de stekker uit het stopcontact.

2. controleer dat het waterniveau in de automaat lager is dan het

deurtje; als dat niet het geval is kunt het water weg laten vloeien

door middel van de afvoerbuis en dit opvangen in een emmer,

zoals aangegeven in de afbeelding.

3. verwijder het paneel aan de voorkant van de Wasdroogmachine

(zie volgende pagina).

4. trek het lipje aangegeven in de afbeelding naar voren totdat

het plastic bandje loskomt; trek hem daarna naar beneden totdat

u klik hoort, wat aangeeft dat de deur is geopend.

5. monteer het paneel weer, met de haakjes goed bevestigd in

de juiste openingen, voordat u het paneel tegen de machine

aandrukt.

! De wasmachine is ontworpen en geproduceerd volgens de

internationale veiligheidsnormen. Deze aanwijzingen zijn voor

uw eigen veiligheid geschreven en moeten aandachtig worden

doorgenomen.

Algemene veiligheid

• Ditapparaatisuitsluitendontworpenvoorhuishoudelijk

niet-professioneel gebruik.

•Ditapparaatmagalleendoorkinderenvan8

jaar en ouder, door personen met een beperkt

lichamelijk, sensorieel of geestelijk vermogen,

of met onvoldoende ervaring of kennis

worden gebruikt, mits ze worden begeleid,

of wanneer zij toereikende instructies hebben

gekregen betreffende het veilige gebruik van

het apparaat en mits zij op de hoogte zijn

vandebetreffendegevaren.Kinderenmogen

niet met het apparaat spelen. Onderhoud en

reiniging mogen niet door kinderen zonder

supervisie worden uitgevoerd.

- Geen ongewassen kledingstukken drogen.

 -Kledingdiebevuildismetstoffenzoalskookolie,

aceton, alcohol, benzine, kirosine, vlekkenverwijderaar,

terpentine, was en stoffen om was te verwijderen

moet met een grotere hoeveelheid wasmiddel in

warm water gewassen worden alvorens de kleding

in de wasdroger te drogen.

- Voorw erpe n zoal s schu imr u bbe r,

douchemutsen, waterdichte stoffen, artikelen

met een rubberen kant en kleding of kussens

die onderdelen van schuimrubber bevatten

mogen niet in de wasdroger gedroogd worden.

- Wasverzachter en gelijksoortige producten

moeten overeenkmostig de instructies van de

fabrikant gebruikt worden.

- Het laatste deel van een droogcyclus wordt

uitgevoerd zonder warmte (koelcyclus) om te

zorgen dat de artikelen niet beschadigd worden.

LET OP: Stop de wasdroger nooit voordat het

droogprogramma beeindigd is. In dit geval

snel al het wasgoed uit de droger halen en het

wasgoed ophangen om het snel te laten drogen.

• Raakdemachinenietaanalsublootsvoetsbentofmetnatte

of vochtige handen of voeten.

• Trekdestekkernooituithetstopcontactdooraanhetsnoer

te trekken, maar altijd door de stekker zelf beet te pakken.

• Openhetwasmiddelbakjenietterwijldemachineinwerkingis.

• Raakhetafvoerwaternietaanaangezienhetbehoorlijkwarm

kan zijn.

• Forceerdedeurnooit:hetveiligheidsmechanisme dateen

ongewild openen van de deur voorkomt, kan beschadigd worden.

• Probeer in geval van storingen nooit zelf de interne

mechanismen van de Wasdroogmachine te repareren.

• Zorgervoordatkleinekinderenniettedichtbijdemachine

komen als deze in werking is.

• Dedeurkantijdenshetwassenzeerheetworden.

• Alsdemachine verplaatst moet worden,doe dit dan met

twee of drie personen tegelijk en zeer voorzichtig. Doe dit

nooit alleen, want het apparaat is erg zwaar.

• Voordat u het wasgoed in de automaat laadt, moet u

controleren of hij leeg is.

•Deglazenruitwordtwarmgedurendehetdrogen.

• Drooggeenwasgoed dat metontvlambare

oplosmiddelen is gewassen (b.v. trieline).

• Drooggeenschuimrubberofelastomerenof

20

1

2

3

20

NL

Beschrijving van de

Wasdroogmachine

Bedieningspaneel

Knop

TEMPERATUUR

DRAAIKNOP

PROGRAMMA’S

Wasmiddelbakje

Knop ON/OFF

Knop

CENTRIFUGE

Knopencontrolelampje

START/PAUSE

Knop

UITGESTELDE

START

Knoppen

OPTIE

Wasmiddelbakje: voor wasmiddelen en wasversterkers

(zie “Wasmiddelen en wasgoed”).

KnopON/OFF : druk even op de toets om de

Wasdroogmachine aan of uit te zetten. Het groen

START/PAUSE controlelampje dat langzaam knippert

geeft aan dat de Wasdroogmachine aanstaat. Om

de Wasdroogmachine tijdens de wascyclus uit te

zetten moet u de toets iets langer, circa 3 seconden,

ingedrukt te houden. Als u de toets kort, of per ongeluk

indrukt zal de Wasdroogmachine niet uitgaan. Als u de

Wasdroogmachine tijdens de wascyclus uitdoet wordt de

cyclus automatisch geannuleerd.

KnopPUSH&WASH+DRY: (zie “Wasmiddelen en wasgoed”)

DRAAIKNOP PROGAMMA’S voor het instellen van het

gewenste programma (zie “Programmatabel”).

KnoppenOPTIE: om de beschikbare opties te selecteren.

Het controlelampje van de gekozen optie zal aanblijven.

KnopTEMPERATUUR : druk hierop om de

temperatuur te verminderen of om met koud water te

wassen: de waarde wordt op het display aangegeven.

KnopCENTRIFUGE : druk hierop om het

centrifugetoerental te verminderen of om de centrifuge in

zijn geheel uit te sluiten; de waarde wordt op het display

aangegeven.

KnopUITGESTELDE START : druk om een

uitgestelde start voor het gekozen programma in te stellen;

het uitstel wordt op de display aangegeven.

Knop DROGEN: druk hierop om het drogen te

verminderen of volledig uit te sluiten. Het gekozen

droogniveau of droogtijd leest u af op het display (zie “Het

uitvoeren van een was- of droogcyclus”).

KnopencontrolelampjeSTART/PAUSE : als het

groen controlelampje langzaam knippert, moet u op de

toets drukken om de wascyclus te starten. Als de cyclus

is gestart blijft het controlelampje vast aanstaan. Als u de

wascyclus wilt pauzeren drukt u nogmaals op de toets; het

controlelampje wordt amberkleurig en gaat knipperen. Als

het symbool niet aan is kunt u de deur openen. Om het

programma te hervatten drukt u opnieuw op de toets.

Stand- by modus

Deze Wasdroogmachine beschikt, in overeenkomst met

de nieuwe normen betreffende de energiebesparing,

over een systeem wat het apparaat automatisch na

30 minuten uitschakelt (stand-by) indien men het niet

gebruikt.DrukkortopdeON-OFFtoetsenwachttotde

Wasdroogmachine weer aangaat.

Gebruik in off-mode: 0,5 W

Gebruik in Left-on: 8 W

DISPLAY

Knop

PUSH&WASH+DRY

Knop

DROGEN

Sayfa yükleniyor ...

Indesit XWDE 861480X WSSS EU Kullanici rehberi

Indesit XWDE 861480X WSSS EU Kullanici rehberi

Diğer dillerde

İlgili Makaleler

Diğer Belgeler