Dell PowerEdge C6220 Hızlı başlangıç Kılavuzu

Dell PowerEdge

C6220

Getting Started

With Your System

Začínáme se systémem

Guide de mise en route du système

Handbuch zum Einstieg mit dem System

Τα πρώτα βήματα με το σύστημά σας

Rozpoczęcie pracy z systemem

Начало работы с системой

Introducción al sistema

Sisteminizi Kullanmaya Başlarken

Dell PowerEdge

C6220

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. Intel® and Intel® Xeon® are registered trademarks of Intel Corporation in the

U.S. and other countries. Red Hat Enterprise Linux® and Enterprise Linux® are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix® and XenServer® are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B08S

September 2013 P/N NKPFX Rev. A04

Getting Started With Your System | 3

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:

•

Access can only be gained by service persons or by users

who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

•

Access is through the use of a

tool

or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To

avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 4

1

Push on the latch release buttons on the end piece midpoints to open

the rail latches. See Figure 1.

2

Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U. See Figure 1.

NOTE:

The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

Figure 1 Pushing the Latch Release Buttons

NOTE:

To remove the rails, push on the latch release button on the end piece

midpoint and unseat each rail.

Getting Started With Your System | 5

3

Engage the end of the rails and release the latch release button to

have the latches locked in place. See Figure 2.

Figure 2 Releasing the Latch Release Buttons

Getting Started With Your System | 6

4

On each vertical rack flange on the back, put two screw bases into

the two square holes right above the rail. See Figure 3.

5

Install the chassis stabilizer shipping brackets (optional) on the back

rack flanges. See Figure 3.

6

Simultaneously fasten the screws. See Figure 3.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Figure 3 Installing the Chassis Stabilizer Shipping Brackets

Getting Started With Your System | 7

7

Slide the system into the rack. See Figure 4.

8

Tighten the thumbscrews to secure the ears of the system to the front

of the rack flanges. See Figure 4.

Figure 4 Installing the Chassis onto the Rack.

Getting Started With Your System | 8

Optional-Connecting the Keyboard, Mouse, and Monitor

Figure 5 Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor’s

cable connector.

Getting Started With Your System | 9

Connecting the Power Cable(s)

Figure 6 Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such as

an uninterrupted power supply or a power distribution unit.

NOTE:

The power input: 110 V and 220 V.

Getting Started With Your System | 10

Turning on the System

Figure 7 Pressing the Power Button on the Front and the Monitor

Figure 8 Pressing the Power Button on the Back

Press the power button(s) either on the front or back of the system and on the

monitor. The power indicators should light green.

Getting Started With Your System | 11

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased with

the system.

NOTE:

For the latest information on supported operating systems, see

dell.com/ossupport

.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at

support.dell.com/manuals

.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at

support.dell.com/manuals

.

NOTE:

Always check for updates on

support.dell.com/manuals

and read the

updates first because they often supersede information in other documents.

NOM Information (Mexico Only)

The following information is provided on the device described in this document

in compliance with the requirements of the official Mexican standards (NOM):

Importer

Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number

B08S

Supply voltage

100-240 V AC with 1200 W Power

200-240 V AC with 1400 W Power

Frequency

50/60 Hz

Current consumption

12-8 Amps with 1200 W Power

9 Amps with 1400 W Power

Getting Started With Your System | 12

Technical Specifications

Processor (Per System Board)

Processor type Two Intel Xeon Processor E5-2600 Series

product family

Chipset

Chipset type Intel PCH-J chipset

Expansion Bus (Per System Board)

Bus type PCI Express Generation 3

Expansion slots

PCIe Two x16, PCIe slots

1U node: half height

2U node: full height and half height

Mezzanine card PCIe One x8, Mezzanine slot

NOTE:

The mezzanine slot is only active in 2-

processor configuration.

Memory (Per System Board)

Architecture 16 x DDR3 1600/1333 MHz RDIMM or

UDIMM

Memory module sockets

16 x DDR3 DIMM sockets

Memory module capacities 2 GB, 4 GB, 8 GB, 16 GB or 32GB

Minimum RAM

2 GB

Maximum RAM 512 GB

Drives

Hard drives Up to twelve 3.5-inch, hot-swappable

SAS/SATA drives or twenty-four 2.5-inch,

hot-swappable SAS/SATA drives

NOTE:

SAS hard drives are supported by add-on card.

Getting Started With Your System | 13

Connectors (Per System Board)

Back

NIC

Two RJ-45 (10/100/1000 Mbps Ethernet)

COM 9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video 15-pin D-Sub VGA

Management port RJ-45 Ethernet port for remote management

access. The management LAN speed is

10Mbps/100Mbps.

Internal

Micro-SD socket

SD riser card memory socket

Video (Per System Board)

Video type AST2300 on-board video controller, or

AST1300

Video memory 16 MB

Getting Started With Your System | 14

Power

NOTE:

The system doesn’t support a mixed

installation of 1200 W and 1400 W power supplies.

NOTE:

Both of these two PSUs are swappable, and they can support hot swap in any condition if

system has power throttling feature.

AC power supply (per power supply)

Wattage 1200 W

Voltage 100-240 VAC, 50/60 Hz, maximum input

current: 12.0-8.0 Amps

NOTE:

For 1200 W power supply, output 1200 W is for

high line (input 200-240 VAC), output 1023 W is for low

line (input 100-120 VAC).

Heat dissipation 4016.251 BTU/hr maximum

Maximum inrush current Initial In-rush Current cannot exceed 55

Amps (peak). Secondary In-rush Current

cannot exceed 35 Amps (peak).

Wattage

1400 W

Voltage 200-240 VAC, 50-60 Hz, maximum input

current: 9.0 Amps

Heat dissipation 6024.376 BTU/hr maximum.

Maximum in-rush current Initial In-rush Current cannot exceed 55

Amps (peak). Secondary In-rush Current

cannot exceed 25 Amps (peak).

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

Physical

Height 8.68 cm (3.42 in)

Width 44.8 cm (17.6 in)

Depth

79.0 cm (31.1 in)

Weight (maximum

configuration)

41 kg (90.38 lb) (with 12*3.5” HDD)

Weight (empty) 15.3 kg (33.73 lb) (with 2.5” HDD bay)

16.2 kg (35.71 lb) (with 3.5” HDD bay)

Getting Started With Your System | 15

Environmental

NOTE:

For additional information about environmental measurements for specific system

configurations, see

www.dell.com/environmental_datasheets

.

Temperature

Operating 10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

CAUTION:

The maximum number of memory modules

and hard drives supported on 1U and 2U node

configurations, with 130W (4 and 8 core) and 135W

processors, depends on the power supply installed.

Storage

-40° to 65°C (-40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage 5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage 1.88 Grms at 10–500 Hz for 15 min

Maximum shock

Operating One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational orientation

Storage Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

71 G for up to 2 ms;

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

27 G faired square wave pulse with velocity

change at 235 inches/second

(597 centimeters/second)

Getting Started With Your System | 16

Altitude

Operating

-15.2 to 3,048 m (-50 to 10,000 ft.)

Storage

-15.2 to 10,668 m (-50 to 35,000 ft.)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Dell PowerEdge

C6220

Začínáme

se systémem

Poznámky a upozornění

POZNÁMKA:

POZNÁMKA označuje důležité informace, které umožňují lepší využití

počítače.

UPOZORNĚNÍ: UPOZORNĚNÍ poukazuje na možnost poškození hardwaru

nebo ztráty dat v případě nedodržení pokynů.

VAROVÁNÍ: VAROVÁNÍ upozorňuje na potenciální nebezpečí poškození

majetku, úrazu nebo smrti.

______________

Informace uvedené v tomto dokumentu se mohou bez předchozího upozornění měnit.

Jakákoliv reprodukce těchto materiálů bez písemného povolení společnosti Dell Inc.

je přísně zakázána.

Ochranné známky použité v tomto textu: Dell™, logo DELL a PowerEdge™ jsou ochranné

známky společnosti Dell Inc. Intel® a Intel® Xeon® jsou registrované ochranné známky

společnosti Intel Corporation v USA a dalších zemích. Red Hat Enterprise Linux® a

Enterprise Linux® jsou registrované ochranné známky společnosti Red Hat, Inc. ve

Spojených státech anebo v jiných zemích. Novell® je registrovaná ochranná známka a

SUSE™ je ochranná známka společnosti Novell Inc. v USA a dalších zemích. Citrix® a

XenServer® jsou registrované ochranné známky nebo ochranné známky společnosti Citrix

Systems, Inc. v USA a dalších zemích. VMware® je registrovaná ochranná známka

společnosti VMware, Inc. v USA a dalších zemích.

V této publikaci mohou být použity další ochranné známky a obchodní názvy s odkazem

na společnosti vlastnící tyto známky a názvy nebo na jejich produkty. Společnost Dell Inc.

nemá vlastnické zájmy vůči ochranným známkám a obchodním názvům jiným než svým

vlastním.

Směrnicový model B08S

Září 2013 P/N NKPFX Rev. A04

Sayfa yükleniyor ...

Dell PowerEdge C6220 Hızlı başlangıç ​​Kılavuzu

Dell PowerEdge C6220 Hızlı başlangıç ​​Kılavuzu

Diğer dillerde

Dell PowerEdge C6220 Hızlı başlangıç Kılavuzu

Dell PowerEdge C6220 Hızlı başlangıç Kılavuzu