Samsung HW-N400 Hızlı başlangıç Kılavuzu

HW-N400

USER MANUAL

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code. To see the manual on

your PC or mobile device, download the

manual in document format from Samsung’s

website. (http://www.samsung.com/support)

Design and specications are subject to change

without prior notice.

ENG - iv

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Right Side Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar ------------------------- 3

03 Connecting the Soundbar 4

Connecting Electrical Power

-------------------------

4

04 Connecting to your TV 5

Method 1. Connecting with a Cable

-------------------------

5

– Connecting a TV using an HDMI Cable

-------------------------

5

– Connecting using an Optical Cable

-------------------------

6

Method 2. Connecting Wirelessly

-------------------------

7

– Connecting a TV via Bluetooth

-------------------------

7

05 Connecting an External Device 9

Connecting using an HDMI Cable

-------------------------

9

Connecting using an Optical or Analogue Audio (AUX) Cable

-------------------------

10

06 Connecting a USB 11

Software Update

-------------------------

11

ENG - v

07 Connecting a Mobile Device 12

Connecting via Bluetooth

-------------------------

12

08 Using the Remote Control 13

How to Use the Remote Control

-------------------------

13

Adjusting the Soundbar volume with a TV remote control

-------------------------

15

09 Installing the Wall Mount 16

Installation Precautions

-------------------------

16

Wallmount Components

-------------------------

16

10 Troubleshooting 19

11 Licence 20

12 Open Source Licence Notice 20

13 Important Notes About Service 20

14 SpecicationsandGuide 21

Specications

-------------------------

21

ENG - 2

01 CHECKING THE COMPONENTS

VOL BASS

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Remote Control / Batteries

1 2

AC/DC Adapter (Main Unit) Power Cord

(AC/DC Adapter)

HDMI Cable

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label : Bottom of the Soundbar Main Unit)

• The power components are labelled (1, 2). For more information about power connections, see

page 4.

• For Soundbar wall mounting components, see page 16.

• The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service

Centre or Samsung Customer Care.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

ENG - 3

02 PRODUCT OVERVIEW

Front Panel / Right Side Panel of the Soundbar

Display

Volume

Power

Position the product so

that the SAMSUNG logo

is located on the top.

󰟳

Right Side of the Soundbar

Bottom Panel of the Soundbar

HDMI OUT

(TV-ARC)

DC 24V

USB (5V 0.5A)

AUX IN

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

AUX IN

DC 24V

HDMI OUT

(TV-ARC)

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

󰟵

󰟶

󰟷

󰟸

󰟹

󰟴

󰟳

Source

Selects the source input mode. (D.IN / AUX / HDMI / BT / USB)

• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and

hold the (Source) button for more than 5 seconds.

󰟴

DC 24V Connect the AC/DC power adapter. (Power Supply In)

󰟵

AUX Connect to the Analogue output of an external device.

󰟶

USB Connect a USB device here to play music les on the USB device through the Soundbar.

󰟷

HDMI OUT Connect to the HDMI (ARC) jack on a TV.

󰟸

HDMI IN

Inputs digital video and audio signals simultaneously using an HDMI cable.

Connect to the HDMI output of an external device.

󰟹

D.IN Connect to the digital (optical) output of an external device.

ENG - 4

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2) to connect the Soundbar to an electrical outlet in the following order:

1 Connect the power output cable to the power adapter, and then to the Soundbar.

2

Connect the power cord to a wall socket.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label : Bottom of the Soundbar Main Unit)

HDMI OUT

(TV-ARC)

DC 24V

USB (5V 0.5A)

AUX IN

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

DC 24V

Bottom of the

Soundbar Main Unit

1 AC/DC Adapter

2 Power Cord

Connecting

Electrical Power

• Make sure to rest the AC/DC Adapter at

on a table or the oor. If you place the

AC/DC Adapter so that it is hanging with

the AC cord input facing upwards, water

or other foreign substances could enter

the Adapter and cause the Adapter to

malfunction.

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker

Kit (SWA-8500S) to your Soundbar (Sold separately). For more information, see the

Samsung Wireless Rear Speaker Kit manual.

ENG - 5

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using

the TV’s remote control.

– When you connect using an optical cable, this feature is supported by 2017 Samsung Smart TVs

that support Bluetooth.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on

the TV is changed, you will experience better sound quality. (The TV menu may differ depending on the

TV manufacturer.)

Connecting a TV using an HDMI Cable

Connect to the HDMI IN

(ARC) port of your TV.

HDMI OUT

(TV-ARC)

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN

(ARC)

HDMI Cable

Bottom of the Soundbar

󰟳

TV ARC

󰟴

Connect to the HDMI OUT (TV-ARC)

port of the Soundbar main unit.

Right Side of the Soundbar

1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the right side

of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,

and TV sound is played.

ENG - 6

• If “TV ARC” does not appear in the display window of the Soundbar main unit, conrm that the

cable is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

Connecting using an Optical Cable

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

Optical Cable

(not supplied)

Bottom of the Soundbar

D.IN

󰟳

󰟴

Right Side of the Soundbar

1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV

with a digital optical cable (not supplied).

2. Press the (Source) button on the right side panel or remote control, and then select the “D.IN”

mode.

Auto Power Link

Auto Power Link automatically turns on the Soundbar when the TV is turned on.

1. Connect the Soundbar and a TV with a digital optical cable (not supplied).

2. Press the Left button on the remote control for 5 seconds to turn Auto Power

Link on or off.

• Auto Power Link is set to ON by default.

(To turn off this function, turn off Auto Power on the Soundbar.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

ENG - 7

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

The initial connection

1. Press the (Source) button on the right side panel or on the remote control, and then select

“BT”.

2. Change “BT” to “BT PAIRING”.

• When “BT READY” appears, press the PAIR button on the remote control or press and hold

the (Source) button on the right side panel of the Soundbar for more than 5 seconds to

display “BT PAIRING”.

3. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

4. Select “[AV] Samsung Soundbar Nxxx N-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV Bluetooth device list.

To connect the TV to the Soundbar, select the message, and then establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

5. You can now hear TV sound from the Soundbar.

NOTE

• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to

reconnect. See Page 8 for details.

ENG - 8

If the device fails to connect

• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Nxxx N-Series”)

appears in the list, delete it.

• Press the PAIR button on the remote control or in “BT” mode, press and hold the (Source)

button for more than 5 seconds on the right side of the Soundbar to switch to “BT PAIRING” mode.

Then, select “[AV] Samsung Soundbar Nxxx N-Series” from the TV’s search list.

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously

connected mobile device to the Soundbar.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button

on the remote control or press and hold the (Source) button for more than 5 seconds on the

right side of the Soundbar while in “BT” mode.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the

Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 5 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

Disconnecting the Soundbar from the TV

Press the (Source) button on the right side panel or on the remote control and switch to any mode

but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.

(The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the

p (Play/Pause) button on the remote control for 5 seconds in “BT READY” status. (Toggle On → Off)

ENG - 9

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound

through the Soundbar.

Connecting using an HDMI Cable

HDMI OUT

(TV-ARC)

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN

(ARC)

HDMI OUT

HDMI Cable

Bottom of the Soundbar

󰟳

󰟴

HDMI

󰟶

External Device

Right Side of the Soundbar

󰟵

1. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the back of the product to the HDMI

IN jack on your TV.

2. Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack on

your digital device.

3. Press the (Source) button on the right side panel or on the remote control, and then select

“HDMI”.

4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.

ENG - 10

Connecting using an Optical or Analogue Audio (AUX) Cable

HDMI OUT

(TV-ARC)

DC 24V

USB (5V 0.5A)

AUX IN

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

- AUDIO -

R L

Bottom of the Soundbar

Optical Cable

(not supplied)

󰟴

Audio (AUX) Cable

(not supplied)

󰟳

BD / DVD player / Set-top box /

Game console

Right Side of the Soundbar

1 Audio (AUX) Cable

X Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an

audio cable.

Y Select “AUX” mode by pressing (Source) button on the right side panel or on the remote

control.

2 Optical Cable

X Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source

Device using a digital optical cable (not supplied).

Y Select “D.IN” mode by pressing the (Source) button on the right side panel or on the remote

control.

ENG - 11

06 CONNECTING A USB

You can play music les located on USB storage devices through the Soundbar.

HDMI OUT

(TV-ARC)

DC 24V

USB (5V 0.5A)

AUX IN

HDMI IN

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

Micro USB to

USB adapter Cable

(not supplied)

USB

Display

USB port

1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one

end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your

Soundbar.

• The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service

Centre or Samsung Customer Care.

2. Connect your USB device to the female end of the adapter cable.

3. Press the (Source) button on the right side panel or on the remote control, and then select

“USB”.

4. “USB” appears in the display screen.

5. Play music les from the USB storage device through the Soundbar.

• The Soundbar automatically turns off (Auto Power Off) if no USB device has been connected for

more than 5 minutes.

Software Update

SamsungmayofferupdatesfortheSoundbar’ssystemrmwareinthefuture.

If an update is offered, you can update the rmware by connecting a USB device with the rmware

update stored on it to the USB port on your Soundbar. For more information about how to download

update les, go to the Samsung Electronics website at (www.samsung.com



Support).

Then, enter or select the model number of your Soundbar, select the Software & Apps option, and then

Downloads. Note that the option names can vary.

ENG - 12

07 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of

cabling.

• You cannot connect more than one Bluetooth device at a time.

Bluetooth device

The initial connection

1. Press the (Source) button on the right side panel or on the remote control, and then select

“BT”.

2. Change “BT” to “BT PAIRING”.

• When “BT READY” appears, press the PAIR button on the remote control or press and hold

the (Source) button on the right side panel of the Soundbar for more than 5 seconds to

display “BT PAIRING”.

3. Select “[AV] Samsung Soundbar Nxxx N-Series” from the list that appears.

• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”

appears in the front display.

4. Play music les from the device, connected via Bluetooth, through the Soundbar.

NOTE

• After you have connected the Soundbar to your mobile device the rst time, use the “BT READY”

mode to reconnect. See Page 8 for details.

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Nxxx N-Series”) appears

in the list, delete it.

• Press the PAIR button on the remote control or in “BT” mode, press and hold the (Source)

button for more than 5 seconds on the right side of the Soundbar to switch to “BT PAIRING” mode.

Then, select “[AV] Samsung Soundbar Nxxx N-Series” from the Bluetooth device search list.

For more information about Bluetooth connections, refer to “Connecting a TV via

Bluetooth” on pages 7~ 8.

ENG - 13

08 USING THE REMOTE CONTROL

How to Use the Remote Control

VOL BASS

SOUNDBAR

SOUND

MODE

PAIR

󰟳

󰟴

󰟵

󰟶

󰟷

󰟹

󰟸

󰟺

󰟼

󰟻

󰟳

Power

VOL BASS

SOUND

MODE

PAIR

Turns the Soundbar on and off.

󰟴

VOL BASS

SOUND

MODE

PAIR

Source

Press to select a source connected to the

Soundbar.

󰟵

Mute

VOL BASS

SOUND

MODE

PAIR

Press the (Mute) button to mute the sound.

Press it again to unmute the sound.

󰟶

SOUND MODE

VOL BASS

SOUND

MODE

PAIR

You can select the desired sound effect by

choosing STANDARD or SURROUND.

• DRC (Dynamic Range Control)

Lets you apply dynamic range control to

Dolby Digital tracks. If you press and hold the

SOUND MODE button while in standby

mode, DRC (Dynamic Range Control) turns

on or off. With the DRC turned on, loud sound

is reduced. (The sound may be distorted.)

• Bluetooth Power

This feature automatically turns Soundbar on

when receiving a connection request from a

previously connected TV or Bluetooth device.

The setting is On by default.

– Press and hold the SOUND MODE

button for more than 5 seconds to turn

off Bluetooth Power function.

󰟷

VOL BASS

SOUND

MODE

PAIR

Bluetooth

PAIR

Press the PAIR button. “BT PAIRING” appears in the Soundbar’s display.

You can connect to a new Bluetooth device in this mode by selecting the device from the

Bluetooth device search list.

ENG - 14

󰟸

Play / Pause

VOL BASS

SOUND

MODE

PAIR

Press the p button to pause a music le temporarily.

When you press the button again, the music le plays.

󰟹

VOL BASS

SOUND

MODE

PAIR

Up/Down/

Left/Right

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left/Right on the button to select or set functions.

• Repeat

To use the Repeat function in “USB” mode, press the Up button.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select the

previous music le.

• Anynet+ / Auto Power Link

You can turn Anynet+ and Auto Power Link on or off.

Anynet+ and Auto Power Link are controlled by the Right and Left buttons

respectively.

– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,

you can control your Soundbar with a Samsung TV remote control.

Press and hold the Right button for 5 seconds to toggle Anynet+ ON and OFF.

– Auto Power Link : If the Soundbar is connected to your TV through a digital optical

cable, the Soundbar can automatically turn on when you turn on your TV. Press

and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF.

– Anynet+ / Auto Power Link are set to ON by default.

󰟺

Sound Control

VOL BASS

SOUND

MODE

PAIR

You can select from TREBLE, AUDIO SYNC

, REAR LEVEL, or REAR SPEAKER ON/OFF

.

• To adjust the TREBLE volume, select Sound Control TREBLE, and then use the

Up/Down buttons to adjust the volume within the -6 to +6 range.

• If the video and audio between the TV and your Soundbar are not synchronised, select

AUDIO SYNC in Sound Settings, and then

set audio delay between 0~300 milliseconds

by using the Up/Down buttons. (Except “USB” mode)

• If surround speakers (not supplied) are connected, select REAR LEVEL and use the Up/

Down buttons to adjust the volume within the -6 to +6 range.

The REAR SPEAKER function can be turned ON/OFF by using the Up/Down buttons.

• AUDIO SYNC is only supported in some functions.

ENG - 15

󰟻

VOL BASS

SOUND

MODE

PAIR

BASS

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

Push the button up or down to adjust the bass volume within the -6 to +6 range.

To set the bass volume level to 0, press the button.

󰟼

VOL BASS

SOUND

MODE

PAIR

VOL

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

SOUND

MODE

VOL

BASS

SOUNDBAR

Push the button up or down to adjust the volume.

• Mute

Press the VOL button to mute the sound. Press it again to unmute the sound.

Adjusting the Soundbar volume with a TV remote control

Use the TV menu to set the TV speaker on a Samsung TV to external speakers.

(For more information, see the TV’s user manual.)

• After installing the Soundbar, you can adjust the Soundbar’s volume using the IR remote control

that came with a Samsung TV. (If you do not want to use this function, when the Soundbar is off,

push the BASS button up and hold it for 5 seconds. “OFF-TV REMOTE” appears in the Soundbar’s

display and the function turns off.)

To adjust the volume using only the Samsung TV remote control, push the BASS button up and hold

it for more than 5 seconds until “SAMSUNG-TV REMOTE” appears in the Soundbar display.

– Each time you push the BASS button up and hold it for 5 seconds, the mode switches in the

following order: “SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV

REMOTE”.

• To adjust the Soundbar volume with the remote control that came with a TV made by a third party

manufacturer, turn the Soundbar off, push the BASS button up and hold it for 5 seconds

(“OFF-TV REMOTE” appears on the Soundbar’s display), release the BASS button, and then push the

BASS button up and hold it again for more than 5 seconds. (“ALL-TV REMOTE” appears on the

Soundbar’s display.)

– This function may not be available, depending on the remote control.

– For manufacturers that support this feature, refer to the FULL MANUAL

(www.samsung.com/support).

– This volume control function works with IR TV remotes only. It does not work with Bluetooth

TV remotes (remotes that require pairing)

ENG - 16

09 INSTALLING THE

WALL MOUNT

Installation Precautions

• Install on a vertical wall only.

• Do not install in a place with high

temperature or humidity.

• Verify whether the wall is strong enough to

support the product’s weight. If not, reinforce

the wall or choose another installation point.

• Purchase and use the xing screws or

anchors appropriate for the kind of wall you

have (plaster board, iron board, wood, etc.). If

possible, x the support screws into wall

studs.

• Purchase wall mounting screws according to

the type and thickness of the wall you want to

mount the Soundbar on.

– Diameter: M5

– Length: 35 mm or longer recommended.

• Connect cables from the unit to external

devices before you install the Soundbar on

the wall.

• Make sure the unit is turned off and

unplugged before you install it. Otherwise, it

may cause an electric shock.

Wallmount Components

450mm

Wall Mount Guide

Holder-Screw (2 EA) Screw (2 EA)

Bracket-Wall Mount

(2 EA)

1. Place the Wall Mount Guide against the wall

surface.

• The Wall Mount Guide must be level.

• If your TV is mounted on the wall, install

the Soundbar at least 5 cm below the TV.

5 cm or more

Sayfa yükleniyor ...

Samsung HW-N400 Hızlı başlangıç Kılavuzu

Samsung HW-N400 Hızlı başlangıç Kılavuzu

Diğer dillerde

İlgili Makaleler

Samsung HW-N400 Hızlı başlangıç ​​Kılavuzu

Samsung HW-N400 Hızlı başlangıç ​​Kılavuzu

Diğer dillerde

İlgili Makaleler

Samsung HW-N400 Hızlı başlangıç Kılavuzu

Samsung HW-N400 Hızlı başlangıç Kılavuzu