Yamaha CRW-3200 Kullanım kılavuzu

Kategori
Optik disk sürücüleri
Tip
Kullanım kılavuzu

Bu kılavuz için de uygundur

(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation, USA.
Address: 6660 Orangethorpe Avenue
Buena Park, CA 90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW3200
CRW3200NB
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.
6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
DANGER - VISIBLE AND / OR INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Product Class: Class 1
Laser Diode Properties
Wavelength: 780 787 nm
Pulse Durations and Max. Output
at the lens of the Laser Pickup Unit
Read Mode: 0.85 mW (Continuous)
Write Mode: Max. 48 mW
(for 212 ns, Min. Cycle 57.9 ns)
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
Lemploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
Laserprodukt-Klasse: Klasse 1
Eigenschaften der Laserdiode
Wellenlänge: 780 787 nm
Impulsdauer und max. Ausgang an der Linse der
Laser-Abtasteinheit
Lesemodus: 0,85 mW (kontinuierlich)
Schreibmodus: Max. 48 mW
(für 212 ns, Zyklusmin. 57,9 ns)
Classe du produit laser: Classe 1
Caractéristiques de la diode laser
Longueur d’onde: 780 787 nm
Durée des impulsions et sortie maximum depuis
la lentille du bloc capteur optique
Mode de lecture: 0,85 mW (continue)
Mode de gravure: max. 48 mW
(pour 212 ns, cycle min. 57,9 ns)
Clase de producto láser: Clase 1
Propiedades del diodo láser
Longitud de onda: 780 787 nm
Duración del pulso y potencia de salida máxima
en el objetivo de la unidad captora láser
Modo de lectura: 0,85 mW (continua)
Modo de escritura: máx. 48 mW
(para 212 ns, ciclo mínimo 57,9 ns)
i
OWNER’S MANUAL
English
ii
SAFETY PRECAUTIONS
PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY
TO PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.
These precautions explain how to use the device properly and safely, thereby
preventing injury to yourself and others. This section has been sub-divided into a
WARNING section and a CAUTION section, according to the likelihood and nature
of any potential injuries or damage inflicted. They relate to your personal safety,
and also help you prevent the risk of damage to the device. Please read these
sections carefully prior to proceeding.
WARNING
Always follow these basic precautions to avoid short-circuit, damage, fire, or
other hazards, and to avoid serious injury or fatal accident from electrical shock.
Do not attempt to open or disassemble the device to avoid the risk of electrical
shock, fire, or malfunction.
Do not look directly at the laser source to avoid the risk of eye damage or
blindness.
Do not insert fingers or foreign objects into the device to avoid the risk of
electrical shock, fire, malfunction, or personal injury.
Do not expose the device to high humidity or place liquid containers such as a
flower vase on the device to avoid the risk of electrical shock, fire, or
malfunction.
Do not expose the device to temperature outside the range 5 – 40 °C (41 – 104
°F) to avoid the risk of fire, deformation of the device panel, or malfunction.
Do not expose the device to dusty place to avoid the risk of fire or malfunction.
Always follow the owner's manual to set up or connect the devices properly to
avoid the risk of electrical shock, fire, malfunction, or personal injury.
If unusual smells, sounds or smoke come from the device, or if foreign objects
such as liquid get into the device, turn off and unplug the computer immediately
to avoid the risk of electrical shock, fire, or malfunction. Contact the store of
purchase or your nearest Yamaha dealer (listed at the back of this manual).
iii
Be sure that the computer is electrically grounded to avoid the risk of electrical
shock.
Prior to cleaning the drive, always unplug the computer or do not handle the plug
with wet hands to avoid the risk of electrical shock.
CAUTION
Always follow these basic precautions to avoid physical injury to yourself or
others, and damage to the device or other property.
Always unplug the computer if it will not be used for a prolonged period of time
or if there is possibility of lightning, to avoid the risk of electrical shock, fire, or
short-circuit.
Do not use the device near other electrical appliances such as televisions, radios,
or speakers to avoid the risk of interferences between each other.
Do not place the computer unstably to avoid the risk of malfunction or personal
injury by its falling down.
Do not place the device with a possibility of excessive vibration to avoid the risk
of damage to written data or malfunction.
Place the device horizontally to avoid the risk of damage to written data.
Prior to transporting the device, remove the disc from the disc tray to avoid the
risk of damage to written data.
Use soft, dry cloths to wipe the device. Do not use benzene, paint thinner,
detergents, or chemically treated wiped cloths, and do not place vinyl, plastic, or
rubber objects on the device to avoid the risk of malfunction or damage to
surface of the device.
Do not rest your weight on or place heavy objects on the device, and do not apply
excessive force to the buttons, switches, or connectors to avoid the risk of
damage to the device or personal injury.
Do not listen to audio with headphones at high volume for prolonged period of
time to avoid auditory disorder.
iv
Prior to turning on the computer, always minimize the volume to avoid auditory disorder
by a sudden burst of sound at high volume.
Do not place the device near magnets or anything magnetized such as a display to avoid
the risk of interferences between each other.
Have the device serviced regularly to avoid internal dust buildup that can cause
malfunction, damage or fire. For service information and service charges, contact the
store of purchase or your nearest Yamaha dealer (listed at the back of this manual).
This drive is for use only with movable equipment, weighing less than 18 kg.
WARRANTY
YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR
AS A RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE
MANUAL THAT COMES WITH THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY
DATA CAUSED AS A RESULT OF USING THIS PRODUCT.
Precautions for Transportation
Transporting the device unfixed may damage its internal mechanism or circuits.
Remove the disc from the disc tray of the device.
Put the device in the original box.
Prior to use, check that the complete accessories are included. (Refer to the original box.)
To reduce power consumption of the CRW3200E drive, set your computer to power saving
mode. (P. 36)
©2001 YAMAHA CORPORATION. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted, or reduced to any electronic medium of machine readable form
without prior consent in writing from Yamaha.
Windows is a registered trademark of Microsoft Corporation.
SafeBurn is a trademark of Yamaha Corporation.
All other trademarks are the property of their respective companies.
v
Table of Contents
Features of the CRW3200E Drive .................................................1
Names and Functions of Parts.....................................................2
Front Panel...............................................................................................2
Rear Panel................................................................................................3
Precautions on Use.................................................................. 4
Handling Discs ........................................................................................4
Copyright.................................................................................................4
Disclaimer of Indemnity..........................................................................4
Useable discs ...........................................................................................5
System Requirements ..............................................................................7
Preparing the CRW3200E Drive ...................................................8
Serial Number..........................................................................................8
1 Decide the Installation Method............................................................9
2 Set the Jumper Switch .......................................................................14
3 Install the CRW3200E Drive.............................................................16
4 Check Recognition of the CRW3200E Drive....................................22
5 Install CD Writing Software..............................................................25
Loading/Ejecting a Disc ...........................................................26
Troubleshooting.....................................................................28
Firmware.............................................................................34
CRW3200E Drive Specifications .................................................35
Technical Notes.....................................................................38
Buffer Underrun Protection Function....................................................38
Writing Methods....................................................................................38
For details about how to install and use the CD writing software, refer to the
documentation that comes with it.
The information contained in this manual is subject to change without prior notice.
Reproduction of this manual, either in part or in full, is expressly forbidden.
1
Features of the CRW3200E Drive
High speed writing/reading
The CRW3200E drive supports up to 24X-speed writing for CD-R discs, and up
to 10X-speed writing/rewriting for CD-RW discs. In addition, the drive
supports data reading and digital audio data extraction at up to 40X speed.
Tip
The Partial CAV method permits 24X-speed writing for CD-R discs.
The CLV method and the 4X 10X Full CAV method permit 10X-speed writing/
rewriting for CD-RW discs.
SafeBurn™ (Enhanced stability writing technology)
The generous 8MB buffer memory provides sufficient data storage to enable
stable disc writing at high speeds. Even if data transfer from the computer is
interrupted, the Buffer Underrun Protection function is activated to save CD-R
discs from a writing error. (P. 38)
Optimum Write Speed Control adjusts the writing speed to the optimum rate
for every CD-R disc automatically. You can set the maximum writing speed
with your CD writing software.
Optimum Write Speed Control can be activated when the maximum writing
speed is set at 12X or more.
The minimum writing speed to be automatically selected is 8X. Manually set the
optimum writing speed if a writing speed supported by a disc is less than 8X.
High fidelity digital audio
The CRW3200E drive supports extraction of digital audio data at up to 40X
speed using CD writing software, as well as recording digital audio with high
fidelity even at 24X-speed writing. For higher quality audio, the CRW3200E
drive provides a digital audio output jack which can be connected to the sound
card with an SPDIF (digital audio) input jack, if your computer has one
installed, with an optional digital audio cable.
Audio Master Quality Recording (High quality audio writing mode)
Audio Master Quality Recording enables you to create high quality audio CDs.
This mode is available for CD-R discs with a capacity of 650MB and 700MB.
(P. 40)
Audio CDs that are created with Audio Master Quality Recording may not be
played back on certain audio recorders and CD-R/RW drives.
CD-MRW (CD Mount Rainier ReWriting)
CD-MRW is a new standard of packet writing. Compared to the ordinary packet
writing, CD-MRW provides many useful functions such as background
formatting. (P. 40)
Note
Note
2
Names and Functions of Parts
Disc tray
Holds the disc. It is opened or closed by
pressing the eject button. (P. 26)
Manual eject hole
Forcibly opens the disc tray when the
tray cannot be opened by pressing the
eject button. (P. 27)
Eject button
Press to open or close the disc tray.
(P. 26)
Headphone jack
Connects headphones or external
speakers to the drive; has stereo mini-
jack specifications.
Headphone volume dial
Controls the volume of the headphones.
The volume increases as the dial is turned
to the right.
LED
Indicates the operational status of the
CRW3200E drive by its colors and
blinking patterns.
Lights or blinks blue
Lights: Standby (with disc)
Blinks: Opening/Closing disc tray, or
reading disc information (TOC)
Blinks rapidly: Playback audio
Blinks irregularly: Reading data
Lights or blinks purple
Lights: Standby (no disc) or the disc tray
is open
Blinks: Accessing for writing or test
writing
Blinks rapidly: Writing
Blinks orange
Malfunction
Off
Power saving (operated via computer
setting)
Front Panel
➃➄
➀➂
Names and Functions of Parts
3
DIGITAL AUDIO OUT
Connects to the sound card in the
computer if the sound card has an SPDIF
(digital audio) input jack using an
optional digital audio cable. (P. 20)
ANALOG AUDIO OUT
Connects to the sound card in the
computer using the included audio cable.
(P. 19)
Jumper switch
Insert a plastic shunt into the switch to
set the connection of the IDE to master or
slave. The switch is set at slave by
default. (P. 14)
IDE INTERFACE CONNECTOR
Connects the included 40-pin IDE cable.
(P. 17)
DC INPUT
Connects the 4-pin internal power cable
of the computer. (P. 21)
Rear Panel
➀➂
4
Precautions on Use
To avoid trouble, such as writing errors, loss of recorded data, and malfunction
of the drive, take the following precautions when handling discs.
Do not place discs in a hot or damp place or where they will be exposed to
direct sunlight.
Do not touch the disc surface. Hold the disc by the edge when handling it.
Remove dust and dirt from the disc surface. Use an air spray to remove dust.
The disc surface may be scratched if strongly wiped with a dry cloth.
Do not stick labels to the disc surface or write anything on it except where
designated.
Do not clean discs with chemicals or detergents.
Do not bend or drop discs.
It is prohibited by law to duplicate copyright material for non-personal use
without the prior consent of the copyright holder. When copying material with
your CD-R/RW drive, take due care not to infringe the copyright.
Yamaha assumes no liability for the loss of any profits incurred as a result of
the loss or corruption of data written on a CD-R or CD-RW, for any loss or
damage caused by or arising out of extraordinary circumstances (including
circumstances that Yamaha has foreseen or could foresee), nor for any
damages incurred or claimed by a third party.
After handling important data, make a comparison between the original and
the copied data (to confirm that the data has been copied properly).
In no event shall Yamaha be liable for any damage to discs due to a Buffer
Underrun Error (P. 38) or for any other reason, or the inability to use
distributed discs with your drive.
Yamaha assumes no liability for the inability to write/playback discs because
of their format.
Handling Discs
Copyright
Disclaimer of Indemnity
Precautions on Use
5
Discs that can be written on
The CRW3200E drive can write on the following discs.
For the latest information about discs previously checked for compatibility with
the drive, refer to the YAMAHA CD-R/RW Drive website URL:
http://www.yamaha.co.jp/english/product/computer/
Useable discs
CD-R discs
The CRW3200E drive can write at 1X, 2X, 4X, 8X, 12X, 16X or 24X speed.
CD-R discs can be played back on a CD-ROM drive or a CD player.
24X-speed writing is enabled with Partial CAV method. (P. 6)
Check the writing speeds your disc supports prior to writing.
CD-RW discs
The CRW3200E drive can write/rewrite at 2X or 4X speed.
CD-RW discs can be read/played back on a device (e.g. CD-ROM drive)
that supports CD-RW discs.
Some discs support only 2X speed.
High Speed CD-RW discs
The CRW3200E drive can write/rewrite at 4X, 8X or 10X speed.
High Speed CD-RW discs can be read/played back on a CD-RW drive
that bears the High Speed CD-RW logo or a device (e.g. CD-ROM drive)
that supports CD-RW discs.
When using the packet writing method (P. 40) for writing/rewriting onto High
Speed CD-RW discs, you can select the 4X 10X Full CAV method. For more
information refer to the documentation that comes with your CD writing
software. (Your CD writing software must support the Full CAV method, as
does the CD Writing software that comes with the CRW3200E drive.)
The Full CAV method is recommended when opening and editing a file on a
CD-RW disc with an application.
In order to write, erase, read or play back High Speed CD-RW discs, use a CD-
R/RW drive that bears the High Speed CD-RW logo. When using a CD-ROM
drive to read/play back High Speed CD-RW discs, use a drive that supports
CD-RW discs.
If these discs are used with a CD-R/RW drive not bearing the High Speed CD-
RW logo, the discs may not be recognized, resulting in a computer not
operating properly or other malfunctions occurring.
Refer to the YAMAHA website below prior to attempting to read/play back
these discs on a YAMAHA CD-R/RW drive not bearing the High Speed CD-
RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
Note
Note
Note
6
Partial CAV (Constant Angular Velocity)
The CLV (Constant Linear Velocity) method is generally used to write data on a
CD-R disc. In writing using the CLV method, the disc rotation speed is adjusted to
keep the data writing speed (data transfer rate) constant on all parts of the disc.
In contrast, the CAV (Constant Angular Velocity) method exercises control so as to
keep the disc rotation speed constant. Since the CAV method makes it possible to
substantially increase the maximum data transfer rate without straining of the drive,
it is adopted today for most CD-ROM drives.
CD formats define the constant linear density of written data so that the amount of
written data per disc rotation will increase as the writing point moves from the inner
track to the outer track.
With the CAV method, therefore, data is transferred at a higher rate when it is
written on the outer tracks of the disc. To achieve 24X-speed writing, the
CRW3200E drive employs the Partial CAV method, which is a combination of the
CAV method for inner tracks and the CLV method for outer tracks.
The Partial CAV method controls the disc rotation speed so that the CRW3200E
drive starts writing at 18X speed on inner tracks, increasing the speed to 24X as the
read/write head moves outward and holds the speed at 24X on outer tracks.
Tip
The CRW3200E drive supports 8cm discs.
Use only circular discs. Do not use any irregular shaped discs such as heart-shaped
or star-shaped discs to avoid the risk of malfunction.
Note
Precautions on Use
7
The CRW3200E drive is designed to operate in the following computer
environment. If your computer does not meet these requirements, the
CRW3200E drive may not write at the maximum speed.
Computer (PC/AT compatible)
CPU: Pentium II-class or higher, 300 MHz or faster
RAM: 32MB (64MB or more is recommended)
64 MB or more is required (128 MB is recommended) for Windows 2000
Professional, while 128 MB or more is required (256 MB is recommended)
for Windows XP.
An empty 5 ¼-inch drive bay (for installing the CRW3200E drive as an
additional drive into the computer)
Hard drive space
Writing data on a CD-R/RW disc requires 50MB to 100MB of free space as a
working area on the hard drive. When writing data on a CD-R/RW disc after
creating an image file, there must be enough free space on the hard drive to
store the image file in addition to the working area (a total of up to 900MB).
However, hard drive space for image files is not required when directly
writing onto a CD-R/RW disc from a hard drive or CD-ROM using the
CRW3200E drive (on-the-fly writing).
Image file
You can collect the data files to be written on a CD-R/RW disc into a single image
file.
The image file is useful for writing the same data onto multiple discs. For details,
refer to the documentation that comes with the CD writing software.
Operating system (OS)
Windows 95 (OSR2 or later), Windows 98, Windows 98 Second Edition,
Windows Me, Windows 2000 Professional, or Windows XP.
CD writing software
The CRW3200E drive requires CD writing software to write onto a CD-R/RW
disc. The CD writing software is included. If using other CD writing software,
be sure that the CD writing software supports the CRW3200E drive.
For details about installing and using the CD writing software, refer to the
documentation that comes with the CD writing software.
System Requirements
8
Preparing the CRW3200E Drive
Preparing tools
Phillips screwdriver: Use the proper screwdriver
for the screws to install the CRW3200E drive into
the computer.
Narrow pliers: Insert and remove the included
plastic shunt for the jumper switch.
The serial number is printed on the label on the top of your CRW3200E drive.
When you have a question about the drive, or need user support services, the
serial number is required.
Please write the serial number down in the space below prior to installing the
CRW3200E drive into your computer. It will be difficult to check the serial
number after installation.
Serial Number
Serial Number
Serial number
(10 characters: 3 letters +
7 numbers)
Preparing the CRW3200E Drive
9
The following describes how to install the CRW3200E drive on the computer
by taking a tower-type computer for example.
The methods of removing the computer cover or panels and installing an internal
device vary depending on the computer model. Refer to the documentation that
comes with the computer.
Check the connection of any IDE device installed to decide the installation
method of the CRW3200E drive.
The CRW3200E drive supports Ultra ATA/33. Even if the motherboard and the
hard drive support Ultra ATA/66 or Ultra ATA/100, they are operated by Ultra
ATA/33 as long as they are connected to the CRW3200E drive by the same IDE
cable or the included 40-pin IDE cable.
Install the CRW3200E drive horizontally.
1
Turn off and unplug the computer.
While the computer is turned on, it is dangerous to handle the internal
computer devices due to the risk of an electrical shock. There is also a risk
of damaging the CRW3200E drive, the computer, etc. Be sure to unplug
the computer prior to handling any internal computer device.
2
Remove all peripheral devices and cables connected to the
computer prior to removing the computer cover.
Clothes and body can become charged with static electricity.
Discharge any static electricity by touching a metallic part of the case or
power unit.
For more information, refer to the documentation that comes with the
computer.
Note
1 Decide the Installation Method
Note
10
Installing the CRW3200E drive as an additional drive
Check the IDE channel (primary/secondary and master/slave) connecting the
CRW3200E drive. (P. 12 13)
An empty 5 ¼-inch drive bay is required to install the CRW3200E drive.
Replacing an existing IDE device with the CRW3200E drive
Connect the CRW3200E drive to the cable that was previously connected to the
existing IDE device.
When replacing a SCSI device, such as a SCSI type CD-ROM drive, do not connect
the CRW3200E drive to the cable that was previously connected to that SCSI
device. Use the included 40-pin IDE cable to connect the CRW3200E drive to the
computer.
Note
Note
CRW3200E
CRW3200E
CD-ROM drive, etc.
Preparing the CRW3200E Drive
11
Examples of connecting the CRW3200E drive
The following describes how to connect the CRW3200E drive for example
recommended by Yamaha.
Example 1: As a secondary slave (For additional drive)
Example 2: As a secondary master (For replacing the existing drive with the
CRW3200E drive)
For the best performance of the CRW3200E drive, Yamaha recommends
that the drive be connected as the sole secondary master.
CD-ROM drive,
etc. (master)
CRW3200E
drive (slave)
IDE cable (primary) IDE cable (secondary)
Hard drive (master)
CRW3200E
drive (master)
Hard drive (master)
IDE cable (primary) IDE cable (secondary)
12
The CRW3200E drive is set at slave by default. If you connect the drive as the
sole secondary master, set the drive to master.
If you connect an IDE device solely to an IDE cable, set the device to master and
connect the drive to the end of the cable.
If you start up the operating system from a SCSI hard drive, etc., there may be no
IDE device connected to the primary. In such a case, Yamaha recommends that
the CRW3200E drive be connected as the primary master.
You may find that the IDE cable has one connector when you try to connect the
removed device to another connector. In such a case, you are required to prepare
an IDE cable with two connectors.
You may have to change the master/slave setting to connect the removed device
to another connector. For more details, refer to the documentation that comes
with the device or refer to the manufacturers website.
E-IDE
E-IDE (Enhanced-IDE) is a standard for connecting computers to IDE devices such
as hard discs, CD-ROMs and CD-R/RW drives. Most computers have two IDE
connectors (primary and secondary). Each connector can be connected to two
devices with an IDE cable.
Two IDE devices connected by one IDE cable are called master and slave.
Note
Slave
Master
Slave
MasterMotherboard Primary
Secondary
Continued on next page
1 / 1

Yamaha CRW-3200 Kullanım kılavuzu

Kategori
Optik disk sürücüleri
Tip
Kullanım kılavuzu
Bu kılavuz için de uygundur