Yamaha RX-V3300 Kullanım kılavuzu

OWNER’S MANUAL

RX-V3300

UA

AV Receiver

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V977800-1

0100V3300(UA)-cv1/4 02.8.21, 7:06 PM1

I CAUTION

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM2

SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

to grounding electrodes, and requirements for the

grounding electrode.

0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM3

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at

least 30 cm on the top, 20 cm on the left and right, and

20 cm on the back of this unit.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping

or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press STANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

IMPORTANT

Please record the serial number of this unit in the

space below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe future reference.

III CAUTION

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM4

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

1

CONTENTS

ADVANCED OPERATION

REMOTE CONTROL FEATURES ................... 46

Control Area ............................................................ 46

Setting the Manufacturer Code ............................... 47

Learn Feature .......................................................... 48

Changing the Source Name in the Display

Window ............................................................... 49

Using the Macro Feature ......................................... 50

Clearing Learned Functions, Macros, Renamed

Source Names, and Setup Manufacturer Codes .. 52

Clearing a Learned Function ................................... 53

Clearing a Macro Function ...................................... 53

Each Component Control Area ............................... 55

SET MENU ........................................................... 60

Adjusting the Items on the SET MENU ................. 60

1 SPEAKER SET (speaker mode settings) ............ 61

2 LOW FRQ TEST ................................................ 65

3 L/R BALANCE (balance of the left and right

main speakers)..................................................... 65

4 HP TONE CTRL (headphone tone control) ........ 66

5 CENTER GEQ (center graphic equalizer) .......... 66

6 INPUT RENAME ............................................... 66

7 I/O ASSIGNMENT ............................................. 67

8 INPUT MODE (initial input mode) .................... 68

9 PARAM. INI (parameter initialization) .............. 68

10LFE LEVEL ........................................................ 68

11D-RANGE (dynamic range) ............................... 69

12SP DELAY .......................................................... 69

13DISPLAY SET .................................................... 70

14MEMORY GUARD ............................................ 71

156CH INPUT SET ................................................ 71

16ZONE2 SET ........................................................ 72

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 73

SLEEP TIMER ..................................................... 74

Setting the Sleep Timer ........................................... 74

Canceling the Sleep Timer ...................................... 74

ZONE 2 ................................................................. 75

Zone 2 Connections ................................................. 75

Remote Control in Zone 2 ....................................... 76

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING .......................................................... 77

What Is a Sound Field? ........................................... 77

Sound Field Program Parameters ............................ 77

Changing Parameter Settings .................................. 78

Resetting a Parameter to the Factory-set Value ....... 78

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS .............................................. 79

TROUBLESHOOTING ....................................... 83

GLOSSARY .......................................................... 88

SPECIFICATIONS .............................................. 90

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the Package Contents ................................ 3

Installing Batteries in the Remote Control ................ 3

CONTROLS AND FUNCTIONS ......................... 4

Front Panel ................................................................ 4

Remote Control ......................................................... 6

Using the Remote Control ......................................... 7

Front Panel Display ................................................... 8

Rear Panel ................................................................. 9

PREPARATION

SPEAKER SETUP ............................................... 10

Speakers to Be Used ................................................ 10

Speaker Placement .................................................. 11

Connecting the Speakers ......................................... 12

CONNECTIONS .................................................. 15

Before Connecting Components ............................. 15

Connecting Video Components ............................... 15

Connecting Audio Components .............................. 18

Connecting the Antennas ......................................... 20

Connecting to an External Amplifier ...................... 21

Connecting to the 6CH INPUT Jacks ..................... 21

Connecting the Power Supply Cords ...................... 22

Turning on the Power .............................................. 23

ON-SCREEN DISPLAY (OSD) .......................... 24

OSD Modes ............................................................. 24

Selecting the OSD Mode ......................................... 24

SPEAKER MODE SETTINGS .......................... 25

Summary of SPEAKER SET Items 1A

through 1H .......................................................... 25

ADJUSTING THE SPEAKER OUTPUT

LEVELS ............................................................ 26

Before You Begin .................................................... 26

TEST DOLBY SUR. ............................................... 26

TEST DSP ............................................................... 28

BASIC OPERATION

BASIC PLAYBACK ............................................. 29

Input Modes and Indications ................................... 31

Selecting a Sound Field Program ............................ 32

Selecting PRO LOGIC, PRO LOGIC

or Neo: 6 ............................................................. 33

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 35

Understanding Sound Fields ................................... 35

Hi-Fi DSP Programs ............................................... 35

CINEMA-DSP ........................................................ 35

Straight Decode ....................................................... 36

Sound Field Effect ................................................... 36

Features of DSP Programs ...................................... 37

Table of Program Names for Each Input Format .... 40

TUNING ................................................................ 41

Automatic and Manual Tuning ................................ 41

Presetting Stations ................................................... 42

Tuning in to a Preset Station ................................... 44

Exchanging Preset Stations ..................................... 44

BASIC RECORDING .......................................... 45

0102V3300_1-9_EN(UA) 02.7.24, 6:04 PM1

2

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are

trademarks of Digital Theater System, Inc.

FEATURES

Built-in 8-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.02% THD, 20 Hz – 20 kHz, 8Ω)

Main: 130 W + 130 W

Center: 130 W

Rear: 130 W + 130 W

Rear center: 130 W

(0.05% THD, 1 kHz, 8 Ω)

Front effect: 25 W + 25 W

Multi-Mode Digital Sound Field

Processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital EX Decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS 96/

24, DTS Neo: 6 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 16 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Video Signal Conversion (S Video ↔ Composite

Video) Capability for Monitor Out

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Macro Capability

◆ PROCESSOR DIRECT for no alteration of the

original signal

◆ Custom Installation Facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

• This manual is printed prior to production. Design and specifications are subject to change in part for the purpose of the improvement

in operativity and others. In this case the product has priority.

0102V3300_1-9_EN(UA) 02.8.21, 6:58 PM2

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

3

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

A

B

CD

DVD

VCR2/DVR

VCR 1

TITLE

MENU

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

EX/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

MUSIC

VIDEO

TV

THEATER

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SEARCH

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

1

5

9

6

10

0

10

100

11 12

78

234

+

Installing Batteries in the Remote

Control

1 Open the battery compartment cover.

2 Insert three supplied batteries (LR6) in the

correct direction by aligning the + and –

marks on the batteries with the polarity

markings (+ and –) on the inside of the

battery compartment.

3 After new batteries are correctly inserted,

press the RESET button in the battery

compartment using a ball point pen or

similar object. (This does not clear the

contents of the memory.)

4 Replace the cover as pressing until it snaps

into place.

■ Notes on batteries

• Change all of the batteries if you notice the condition

like; the operating range of the remote control

decreases, the indicator does not flash or its light

becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

AM loop antenna

Indoor FM antenna

(Australia model only)

Indoor FM antenna

(U.S.A. model only)

Batteries (LR6) × 3

Remote control

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Power Cord

(U.S.A. model only)

RESET button

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM3

4

BASS

VOLUME

VIDEO AUX

SILENT

PROGRAM

STEREO

REC OUT

/ZONE 2

SPEAKERS

INPUT

MODE

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

SOURCE

/REMOTE

MD/TAPE

CD–R

TUNER

CD

PHONO

DVD

D–TV/LD

CBL/SAT

VCR 1

V–AUX

VCR2

/DVR

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

/

ON

NATURAL SOUND AV RECEIVER RX-V3300

TREBLE

–

+

–

+

6CH

INPUT

AB

DIGITAL

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

FM/AM

1 2 34 5 6

7q

w

e

r t y u8 9 0

io

asdp

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 INPUT selector

Selects the input source you want to listen to or watch.

3 (INPUT) MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks of this unit (see

page 31). Priority cannot be set when 6CH INPUT is

selected as the input source.

4 Remote control sensor

Receives signals from the remote control.

5 Front panel display

Shows information about the operational status of this

unit.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

7 PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the PRE OUT/MAIN IN jacks or to the

speakers.

(There is an exception depending on the “1H SP B SET”

setting on the SET MENU.)

8 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each

time the button is pressed, this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

9 PROCESSOR DIRECT

Turns on or off the PROCESSOR DIRECT function at

each time the button is pressed. When this is on, BASS,

TREBLE, and BASS EXTENSION are bypassed,

eliminating any alteration of the original signal.

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM4

5

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

D

I

G

I

T

A

L

N

ATURAL SOUN

D AV REC

EIVER R

X-V3

300

To open, press gently on the lower part of the panel.

0 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel at each time its

corresponding button is pressed.

(Depending on the “1H SP B SET” setting on the SET

MENU, the output from each speaker varies when

SPEAKER B is set to on.)

q BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

w TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the left and

right main speakers.

e REC OUT/ZONE 2

Selects the source you want to direct to the audio/video

recorder and ZONE 2 outputs independent of the source

you are listening to or watching in the main room. When

set to the SOURCE/REMOTE position, the input source

is directed to all outputs.

r STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are mixed down to the main left and

right speakers.

t A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

y PROGRAM l / h

Selects the DSP program.

u 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH INPUT takes

priority over the source selected with INPUT (or the input

selector buttons on the remote control).

i PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

o VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

p PRESET/TUNING EDIT

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset

station number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

a FM/AM

Switches the reception band between FM and AM.

s MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

d TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

■ Opening and closing the front

panel door

When you want to use the controls behind the front panel

door, open the door gently pressing on the lower part of

the panel. When you are not using them, close the door.

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM5

6

CONTROLS AND FUNCTIONS

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

A

B

CD

DVD

VCR2/DVR

VCR 1

TITLE

MENU

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

EX/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

MUSIC

VIDEO

TV

THEATER

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SEARCH

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AUX

POWER

1

5

9

6

10

0

10

100

11 12

78

234

+

1

2

3

4

5

6

7

0

w

e

r

t

9

8

q

y

u

i

o

p

d

g

f

s

j

k

h

a

l

Remote Control

This section describes the controls and their functions of

the remote control. See “REMOTE CONTROL

FEATURES” on pages 46 to 59 for operating other

components with this remote control.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 RE-NAME

Used for changing the input source name in the display

window (see page 49).

3 TRANSMIT indicator

Flashes while the remote control is sending signals.

4 STANDBY

Sets this unit in the standby mode.

5 SYSTEM POWER

Turns on the power of this unit.

6 Display window

Shows the selected source component that you are

controlling.

7 SOURCE SELECT k/n

Selects the another component to control independently

from the input that has been selected by pressing an input

selector button.

8 LIGHT

Turn the light on or off. When you press this button once,

the light turns on for about ten seconds. Press again to

turn off the light.

9 10KEY/DSP

Selects the numeric button (10KEY) mode or DSP mode.

0 Operation buttons

Provides functions such as play, stop, skip, etc. for

operating your other components selected by the input

selector buttons.

q EX/ES

Turns on or off the Dolby Digital EX or DTS ES decoder

with 10 KEY/DSP set to the DSP position.

w LEVEL

Selects the effect speaker channel to be adjusted and sets

the level.

e ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

r SLEEP

Sets the sleep timer.

t TEST

Outputs the test tone to adjust the speaker levels.

y CLEAR

Used for clearing functions acquired when using the learn

and rename features, and set manufacturer codes (see

pages 52 and 53).

u LEARN

Used for setting up the manufacturer code or for

programming the functions of other remote controls (see

pages 47 to 49).

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM6

7

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

BASS

VOLUME

VIDEO AUX

SILENT

PROGRAM

STEREO

REC OUT

/ZONE 2

SPEAKERS

INPUT

MODE

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

SOURCE

/REMOTE

MD/TAPE

CD–R

TUNER

CD

PHONO

DVD

D–TV/LD

CBL/SAT

VCR 1

V–AUX

VCR2

/DVR

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

/

ON

NATURAL SOUND AV RECEIVER RX-V3300

TREBLE

–

+

–

+

6CH

INPUT

AB

DIGITAL

30°30°

Approximately 6 m (20 feet)

i MACRO

Used to program a series of operations for control by a

single button (see pages 51 and 52).

o MACRO ON/OFF

Turns the macro function on and off.

p Å and ı

Switch the control area for the extra components that are

not connected to this unit without changing the input.

a Input selector buttons

Select the input source and change the control area.

s 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

d DSP program/Numeric buttons

Select DSP programs or numbers according to the

position of 10KEY/DSP.

f MUTE

Mutes the sound. The MUTE indicator turns on when the

MUTE function is on. Press again to restore the audio

output to the previous volume level.

g VOLUME +/–

Increases or decreases the volume level.

h STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are also directed to the main left and

right speakers.

j PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

k Cursor buttons k/n/–/+

Select and adjust DSP program parameters and SET

MENU items according to the position of PARAMETER/

SET MENU.

l Cover

Slides down to use the various setup buttons. Slides up

when these buttons are not being used.

Using the Remote Control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM7

8

CONTROLS AND FUNCTIONS

RL

LCR

RC RR

LFE

VIRTUAL

DTS

Neo

MOVIE TV THEATER

ENTERTAINMENT12

:6

DOLBY DIGITAL

PRO

LOGIC

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

EX

MATRIXDISCRETE

ES

PCM

1

SILENT

96/24

SP

DIGITAL

VCR2/DVR

CBL

/

SAT

MD

/

TAPE

TV

/

LD

STEREO

TUNED

MEMORY

P. DIRECT

BASS

MUTE VOLUME

SLEEP

AUTO

D

96

K

Hz

/

24bit

PRO LOGIC

/

AB

dB

ft

m

S

qw t yuio p sa

2

145687 90

e r

3

1

DSP

indicator

Lights up when you select a digital sound field program.

2 Decoder indicators

When any of the decoders equipped on this unit

functions, the indicator lights up.

3 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see page

34).

4 Input source indicator

Shows the current input source with a cursor.

5 AUTO indicator

Shows that this unit is in the automatic tuning mode.

6 BASS indicator

Lights up while BASS EXTENSION is on.

7 SLEEP indicator

Lights up while the sleep timer is on.

8 MUTE indicator

Lights up while the MUTE function is on.

9 96/24 indicator

Lights up when the DTS 96/24 signal is input to this unit.

0 VOLUME level indicator

Indicates the volume level.

q

PCM

indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

w SILENT indicator

Lights up when headphones are connected with the sound

effect (see “SILENT CINEMA DSP” on page 34).

e SP A B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

Front Panel Display

r Headphones indicator

Lights up when headphones are connected.

t DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2, TV THEATER or V/DTS SURROUND

DSP program is selected.

y Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

u STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

i TUNED indicator

Lights up when this unit tunes in to a station.

o MEMORY indicator

Flashes to show a station can be stored.

p P. DIRECT

Lights up while PROCESSOR DIRECT is on.

a Input channel indicator

Indicates the channel components of input signals being

received.

s

LFE

indicator

Lights up when the input signal contains the LFE signal.

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM8

9

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

AC OUTLETS

AC IN

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL

OUT

SPEAKERS

TUNER

REMOTE

IN

75Ω

UNBAL.

OUT

1

2

RC-232C

AM

ANT

GND

FM ANT

+12V

15mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

DVD

MONITOR

OUT

CBL

/SAT

MAIN

IN

OUT

MAIN

ZONE 2 OUT

REAR CENTER

(SURROUND)

CENTER

FRONT

REAR

EFFECT

PRE OUT/MAIN IN

IMPEDANCE SELECTOR

SELECTEUR D'INPEDANCE

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

FRONT EFFECT

REAR CENTER

P

B

Y

R

L

R

L

R

L

R

L

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

(SURROUND)

COAXIAL

+

–

+

–

+

–

+

–

+

–

+

–

+

–

+

ZONE 2 OUT

MAIN A OR B

CENTER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

ZONE 2 OUT

MAIN A OR B

CENTER

6ΩMIN./

SPEAKER

6ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

A + B

8ΩMIN./

SPEAKER

:

A

B

1

8

9 0rq

2

3

5

7

6

4

w e

(U.S.A. model)

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 18 and 19 for connection information.

3 Video component jacks

See pages 15 to 17 for connection information.

4 RS-232C

These are control expansion terminals for commercial

use. Consult your dealer for details.

5 Speaker terminals

See pages 12 and 13 for connection information.

6 AC OUTLETS

Use these outlets to supply power to your other A/V

components (see page 22).

7 AC INLET (U.S.A. model only)

Use this inlet to plug in the supplied power cable (see

page 22).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 21 for connection information.

0 ZONE 2 OUT jacks

See page 75 for details.

q Antenna input terminals

See page 20 for connection information.

w REMOTE IN/OUT jacks

See page 75 for details.

CONTROL OUT jacks

This is a control expansion terminal for commercial use.

e PRE OUT/MAIN IN jacks

See page 21 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance (see page 14). Set this unit in the

standby mode before you change the setting of this

switch.

Rear Panel

0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM9

10

SPEAKER SETUP

This unit has been designed to provide the best sound-

field quality with an 8-speaker system, using left and right

main speakers, left and right rear speakers, left and right

front effect speakers and a center and rear center

speakers. If you use different brands of speakers (with

different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not

shift smoothly. We recommend that you use speakers

from the same manufacturer or speakers with the same

tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). The

front effect speakers are used for the effect sound. If for

some reason it is not practical to use a center speaker, you

can do without it. Best results, however, are obtained with

the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

PREPARATION

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with a monitor,

place the speakers away from the monitor.

Speakers to Be Used

0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM10

11

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

■ Rear center speaker

Place the rear center speaker in the center between the left

and right rear speakers at the same height from the floor

as the rear speakers.

■ Front effect speakers

Place the front effect speakers about 0.5 - 1 m (1 - 3 feet)

outside the main speakers and in front of the room, facing

slightly inwards, nearly 1.8 m (6 feet) above the floor.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

Speaker Placement

Refer to the following diagram when you place the speakers.

Main speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center speaker

Rear speaker (R)

Subwoofer

Main speaker (R)

Center speaker

Front effect speaker (R)

Front effect speaker (L)

Note

• If you do not use any effect speakers (rear, front effect, center and/or rear center), change the settings of SPEAKER SET items in the

SET MENU to designate the signals to other terminals you connect speakers to.

0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM11

12

SPEAKER SETUP

12

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

y

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Banana plug

3

1

2

0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM12

13

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

AC OUTLETS

AC IN

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL

OUT

SPEAKERS

TUNER

REMOTE

IN

75Ω

UNBAL.

OUT

1

2

RS-232C

AM

ANT

GND

FM ANT

+12V

15mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

DVD

MONITOR

OUT

CBL

/SAT

MAIN

IN

OUT

MAIN

ZONE 2 OUT

REAR CENTER

(SURROUND)

CENTER

FRONT

REAR

EFFECT

PRE OUT/MAIN IN

IMPEDANCE SELECTOR

SELECTEUR D'INPEDANCE

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

FRONT EFFECT

REAR CENTER

P

B

Y

R

L

R

L

R

L

R

L

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

(SURROUND)

COAXIAL

+

–

+

–

+

–

+

–

+

–

+

–

+

–

+

ZONE 2 OUT

MAIN A OR B

CENTER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

ZONE 2 OUT

MAIN A OR B

CENTER

6ΩMIN./

SPEAKER

6ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

A + B

8ΩMIN./

SPEAKER

:

A

B

Subwoofer

system

Rear Center

speaker

Rear speaker

Center

speaker

(U.S.A. model)

Right

Right Left

Front Effect speaker

Right Left

Left

Main B speaker

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

■ FRONT EFFECT SPEAKERS terminals

A front effect speaker system can be connected to these terminals.

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The

LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are

assigned to this jack.

Note

• Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from

the SUBWOOFER jack.

Right Left

Main A speaker

0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM13

14

SPEAKER SETUP

AC OUTLETS

AC IN

MAIN

(SURROUND)

CENTER

FRONT

REAR

EFFECT

IMPEDANCE SELECTOR

SELECTEUR D'INPEDANCE

SET BEFORE POWER ON

L

+

ZONE 2 OUT

MAIN A OR B

CENTER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

ZONE 2 OUT

MAIN A OR B

CENTER

6ΩMIN./

SPEAKER

6ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

A + B

8ΩMIN./

SPEAKER

:

A

B

IMPEDANCE SELECTOR

SELECTEUR D'INPEDANCE

SET BEFORE POWER ON

ZONE 2 OUT

MAIN A OR B

CENTER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

8ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

ZONE 2 OUT

MAIN A OR B

CENTER

6ΩMIN./

SPEAKER

6ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

4ΩMIN./

SPEAKER

FRONT

REAR

REAR CENTER

:

A + B

8ΩMIN./

SPEAKER

:

Switch

position

Upper

Lower

Speaker

Zone 2

Front

Effect

Rear

Center

Rear

Center

Main

Zone 2

Front

Effect

Rear

Center

Rear

Center

Main

Impedance level

The impedance of each speaker must be 6 Ω or higher.

The impedance of each speaker must be 4 Ω or higher.

[Australia model]

The impedance of each speaker must be 6 Ω or higher.

The impedance must be 4 Ω or higher.

[Australia model]

The impedance must be 6 Ω or higher.

If you use one set of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

If you use one set of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 16 Ω or higher.

[U.S.A. model]

The impedance of each speaker must be 8 Ω or higher.

IMPEDANCE SELECTOR switch

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit

may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the

standby mode.

Select the upper or lower position according to the impedance of the speakers in your system. Be sure to move this

switch only when this unit is in the standby mode.

(U.S.A. model)

0103V3300_10-23_EN(UA) 02.8.21, 6:59 PM14

15

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

y

• The signals input through the S VIDEO jacks can be converted

to composite signals inside of this unit and output through the

VIDEO MONITOR OUT jacks on this unit as well.

• The signals input through the VIDEO jack on this unit can be

output through the S VIDEO MONITOR OUT jack by setting

“V CONV.” in “13 DISPLAY SET” on the SET MENU to ON

(see page 70).

• When signals input through both S VIDEO and VIDEO jacks,

signals input through the S VIDEO jack has priority.

• You can designate the input for the COMPONENT VIDEO A

and B jacks according to your component by using “7 I/O

ASSIGNMENT” on the SET MENU (see page 67 for details).

■ VIDEO AUX jacks (on the front

panel)

These jacks are used to connect any video input source

such as a game console and a camcorder to this unit.

Before Connecting Components

CAUTION

Never connect this unit and other components to mains

power until all connections between components have

been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• Use commercially available video pin cables when

connecting to the S VIDEO and COMPONENT

VIDEO jacks.

Connecting Video Components

■ About the video jacks

There are three types of video jacks.

VIDEO jacks transmit composite

signals.

S VIDEO jacks transmit S-video

signals.

S-video signals are separated into

luminance (Y) and color (C) video

signals to achieve high-quality

color reproduction.

COMPONENT VIDEO jacks

transmit component signals.

Component signals are separated

into luminance (Y) and color

difference (P

B, PR) to provide the

best quality in picture

reproduction.

The signal input through these jacks are output through

the MONITOR OUT jacks of the same type.

Make sure to connect the correct jacks of the same type

on your video component and the video monitor.

CONNECTIONS

VIDEO jack

S VIDEO jack

COMPONENT VIDEO jacks

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

O

V

L

R

S

COMPONENT VIDEO

PR PB Y

VIDEO

S VIDEO

Game

console or

video camera

0103V3300_10-23_EN(UA) 7/26/02, 5:46 PM15

16

CONNECTIONS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL

INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL

OUT

TUNER

REMOTE

IN

75Ω

UNBAL.

OUT

1

2

RS-232C

AM

ANT

GND

FM ANT

+12V

15mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

DVD

MONITOR

OUT

CBL

/SAT

MAIN

IN

OUT

PRE OUT/MAI

SUB

WOOFER

REAR

FRONT EFFE

C

REAR CENTER

P

B

Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

CBL

/SAT

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

CD

D-TV

/LD

(SURROUND)

COAXIAL

V

S

L R

VVC

S S

L R

O

L

S

R

V

C

O

COMPONENT

INPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO OUTPUT

COAXIAL OUTPUT

OPTICAL OUTPUT

AUDIO OUTPUT

COMPONENT OUTPUT

VIDEO

OUTPUT

S VIDEO

OUTPUT

V V V

VVV

V

(U.S.A. model)

indicates S-video cables

indicates video cables

indicates coaxial cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

TV/digital TV or

LD player

DVD player

Video

monitor

indicates component video cables

0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM16

Sayfa yükleniyor ...

Yamaha RX-V3300 Kullanım kılavuzu

Yamaha RX-V3300 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler