Yamaha RX-V3300 Kullanım kılavuzu

Kategori
Alıcı
Tip
Kullanım kılavuzu
OWNER’S MANUAL
RX-V3300
UA
AV Receiver
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia
V977800-1
0100V3300(UA)-cv1/4 02.8.21, 7:06 PM1
I CAUTION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM2
SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS
CAUTION II
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 81020)
GROUNDING CONDUCTORS
(NEC SECTION 81021)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.
0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM3
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at
least 30 cm on the top, 20 cm on the left and right, and
20 cm on the back of this unit.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in a environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping
or splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and
may cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
13 To prevent damage by lightning, disconnect the power cord
from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press STANDBY/ON to set this
unit in the standby mode, and disconnect the AC power plug
from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode. In
this state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the
space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe future reference.
III CAUTION
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
0101V3300_Cau_EN(UA) 02.7.24, 6:04 PM4
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADDITIONAL
INFORMATION
ADVANCED
OPERATION
1
CONTENTS
ADVANCED OPERATION
REMOTE CONTROL FEATURES ................... 46
Control Area ............................................................ 46
Setting the Manufacturer Code ............................... 47
Learn Feature .......................................................... 48
Changing the Source Name in the Display
Window ............................................................... 49
Using the Macro Feature ......................................... 50
Clearing Learned Functions, Macros, Renamed
Source Names, and Setup Manufacturer Codes .. 52
Clearing a Learned Function ................................... 53
Clearing a Macro Function ...................................... 53
Each Component Control Area ............................... 55
SET MENU ........................................................... 60
Adjusting the Items on the SET MENU ................. 60
1 SPEAKER SET (speaker mode settings) ............ 61
2 LOW FRQ TEST ................................................ 65
3 L/R BALANCE (balance of the left and right
main speakers)..................................................... 65
4 HP TONE CTRL (headphone tone control) ........ 66
5 CENTER GEQ (center graphic equalizer) .......... 66
6 INPUT RENAME ............................................... 66
7 I/O ASSIGNMENT ............................................. 67
8 INPUT MODE (initial input mode) .................... 68
9 PARAM. INI (parameter initialization) .............. 68
10LFE LEVEL ........................................................ 68
11D-RANGE (dynamic range) ............................... 69
12SP DELAY .......................................................... 69
13DISPLAY SET .................................................... 70
14MEMORY GUARD ............................................ 71
156CH INPUT SET ................................................ 71
16ZONE2 SET ........................................................ 72
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ....................................................... 73
SLEEP TIMER ..................................................... 74
Setting the Sleep Timer ........................................... 74
Canceling the Sleep Timer ...................................... 74
ZONE 2 ................................................................. 75
Zone 2 Connections ................................................. 75
Remote Control in Zone 2 ....................................... 76
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM PARAMETER
EDITING .......................................................... 77
What Is a Sound Field? ........................................... 77
Sound Field Program Parameters ............................ 77
Changing Parameter Settings .................................. 78
Resetting a Parameter to the Factory-set Value ....... 78
DIGITAL SOUND FIELD PARAMETER
DESCRIPTIONS .............................................. 79
TROUBLESHOOTING ....................................... 83
GLOSSARY .......................................................... 88
SPECIFICATIONS .............................................. 90
INTRODUCTION
CONTENTS ............................................................ 1
FEATURES ............................................................. 2
GETTING STARTED ............................................ 3
Checking the Package Contents ................................ 3
Installing Batteries in the Remote Control ................ 3
CONTROLS AND FUNCTIONS ......................... 4
Front Panel ................................................................ 4
Remote Control ......................................................... 6
Using the Remote Control ......................................... 7
Front Panel Display ................................................... 8
Rear Panel ................................................................. 9
PREPARATION
SPEAKER SETUP ............................................... 10
Speakers to Be Used ................................................ 10
Speaker Placement .................................................. 11
Connecting the Speakers ......................................... 12
CONNECTIONS .................................................. 15
Before Connecting Components ............................. 15
Connecting Video Components ............................... 15
Connecting Audio Components .............................. 18
Connecting the Antennas ......................................... 20
Connecting to an External Amplifier ...................... 21
Connecting to the 6CH INPUT Jacks ..................... 21
Connecting the Power Supply Cords ...................... 22
Turning on the Power .............................................. 23
ON-SCREEN DISPLAY (OSD) .......................... 24
OSD Modes ............................................................. 24
Selecting the OSD Mode ......................................... 24
SPEAKER MODE SETTINGS .......................... 25
Summary of SPEAKER SET Items 1A
through 1H .......................................................... 25
ADJUSTING THE SPEAKER OUTPUT
LEVELS ............................................................ 26
Before You Begin .................................................... 26
TEST DOLBY SUR. ............................................... 26
TEST DSP ............................................................... 28
BASIC OPERATION
BASIC PLAYBACK ............................................. 29
Input Modes and Indications ................................... 31
Selecting a Sound Field Program ............................ 32
Selecting PRO LOGIC, PRO LOGIC
or Neo: 6 ............................................................. 33
DIGITAL SOUND FIELD PROCESSING
(DSP) ................................................................. 35
Understanding Sound Fields ................................... 35
Hi-Fi DSP Programs ............................................... 35
CINEMA-DSP ........................................................ 35
Straight Decode ....................................................... 36
Sound Field Effect ................................................... 36
Features of DSP Programs ...................................... 37
Table of Program Names for Each Input Format .... 40
TUNING ................................................................ 41
Automatic and Manual Tuning ................................ 41
Presetting Stations ................................................... 42
Tuning in to a Preset Station ................................... 44
Exchanging Preset Stations ..................................... 44
BASIC RECORDING .......................................... 45
0102V3300_1-9_EN(UA) 02.7.24, 6:04 PM1
2
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are
trademarks of Digital Theater System, Inc.
FEATURES
Built-in 8-Channel Power Amplifier
Minimum RMS Output Power
(0.02% THD, 20 Hz – 20 kHz, 8)
Main: 130 W + 130 W
Center: 130 W
Rear: 130 W + 130 W
Rear center: 130 W
(0.05% THD, 1 kHz, 8 )
Front effect: 25 W + 25 W
Multi-Mode Digital Sound Field
Processing
Dolby Pro Logic/Dolby Pro Logic Decoder
Dolby Digital/Dolby Digital EX Decoder
DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS 96/
24, DTS Neo: 6 Decoder
CINEMA DSP: Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital
or DTS
Virtual CINEMA DSP
SILENT CINEMA DSP
Sophisticated AM/FM Tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
Other Features
96-kHz/24-bit D/A Converter
“SET MENU” which Provides You with 16 Items
for Optimizing This Unit for Your Audio/Video
System
Test Tone Generator for Easier Speaker Balance
Adjustment
6-Channel External Decoder Input for Other
Future Formats
BASS EXTENSION Button for Reinforcing
Bass Response
On Screen Display Function Helpful in
Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Video Signal Conversion (S Video Composite
Video) Capability for Monitor Out
Optical and Coaxial Digital Audio Signal Jacks
Sleep Timer
Remote Control with Preset Manufacturer Codes
and “Learning” Macro Capability
PROCESSOR DIRECT for no alteration of the
original signal
Custom Installation Facility
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this
manual.
This manual is printed prior to production. Design and specifications are subject to change in part for the purpose of the improvement
in operativity and others. In this case the product has priority.
0102V3300_1-9_EN(UA) 02.8.21, 6:58 PM2
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
3
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SOUND
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
MENU
CHAPTER
PAUSESTOPPOWER
REC
HALL 1
EX/ES
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
MUTE
VOLUME
STEREO
TV INPUT
TV VOL
CH
PRESET
DISC
PARAMETER
SET MENU
EFFECT
LEVEL
ON SCREEN
TESTSLEEP
TV MUTE
MUSIC
VIDEO
TV
THEATER
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
CHP/INDEX
A/B/C/D/E
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
+
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
POWER
1
5
9
6
10
0
10
100
11 12
78
234
+
+
Installing Batteries in the Remote
Control
1 Open the battery compartment cover.
2 Insert three supplied batteries (LR6) in the
correct direction by aligning the + and –
marks on the batteries with the polarity
markings (+ and –) on the inside of the
battery compartment.
3 After new batteries are correctly inserted,
press the RESET button in the battery
compartment using a ball point pen or
similar object. (This does not clear the
contents of the memory.)
4 Replace the cover as pressing until it snaps
into place.
Notes on batteries
Change all of the batteries if you notice the condition
like; the operating range of the remote control
decreases, the indicator does not flash or its light
becomes dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing
new batteries.
If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
AM loop antenna
Indoor FM antenna
(Australia model only)
Indoor FM antenna
(U.S.A. model only)
Batteries (LR6) × 3
Remote control
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
Power Cord
(U.S.A. model only)
RESET button
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM3
4
BASS
VOLUME
VIDEO AUX
SILENT
PROGRAM
STEREO
REC OUT
/ZONE 2
SPEAKERS
INPUT
MODE
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET
/
TUNING
PHONES
EFFECT
SOURCE
/REMOTE
MD/TAPE
CD–R
TUNER
CD
PHONO
DVD
D–TV/LD
CBL/SAT
VCR 1
V–AUX
VCR2
/DVR
A/B/C/D/E
S VIDEO
MEMORY
FM/AM
EDIT
PRESET
/TUNING
MAN'L/AUTO FM AUTO/MAN'L MONO
TUNING
MODE
VIDEO AUDIO OPTICALLR
STANDBY
/
ON
NATURAL SOUND AV RECEIVER RX-V3300
TREBLE
+
+
6CH
INPUT
AB
DIGITAL
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
FM/AM
1 2 34 5 6
7q
w
e
r t y u8 9 0
io
asdp
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 INPUT selector
Selects the input source you want to listen to or watch.
3 (INPUT) MODE
Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) to receive when one component is
connected to two or more input jacks of this unit (see
page 31). Priority cannot be set when 6CH INPUT is
selected as the input source.
4 Remote control sensor
Receives signals from the remote control.
5 Front panel display
Shows information about the operational status of this
unit.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
7 PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the PRE OUT/MAIN IN jacks or to the
speakers.
(There is an exception depending on the 1H SP B SET
setting on the SET MENU.)
8 BASS EXTENSION
Turns on or off the BASS EXTENSION function at each
time the button is pressed, this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
9 PROCESSOR DIRECT
Turns on or off the PROCESSOR DIRECT function at
each time the button is pressed. When this is on, BASS,
TREBLE, and BASS EXTENSION are bypassed,
eliminating any alteration of the original signal.
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM4
5
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
D
I
G
I
T
A
L
N
ATURAL SOUN
D AV REC
EIVER R
X-V3
300
To open, press gently on the lower part of the panel.
0 SPEAKERS A/B
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel at each time its
corresponding button is pressed.
(Depending on the 1H SP B SET setting on the SET
MENU, the output from each speaker varies when
SPEAKER B is set to on.)
q BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
w TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.
e REC OUT/ZONE 2
Selects the source you want to direct to the audio/video
recorder and ZONE 2 outputs independent of the source
you are listening to or watching in the main room. When
set to the SOURCE/REMOTE position, the input source
is directed to all outputs.
r STEREO/EFFECT
Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are mixed down to the main left and
right speakers.
t A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
y PROGRAM l / h
Selects the DSP program.
u 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
i PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
o VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
p PRESET/TUNING EDIT
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
a FM/AM
Switches the reception band between FM and AM.
s MEMORY (MANL/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
d TUNING MODE (AUTO/MANL MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the AUTO indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the AUTO indicator does not light up.
Opening and closing the front
panel door
When you want to use the controls behind the front panel
door, open the door gently pressing on the lower part of
the panel. When you are not using them, close the door.
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM5
6
CONTROLS AND FUNCTIONS
TRANSMIT
RE-NAME
STANDBY
6CH INPUT
SOUND
SYSTEM
CLEAR LEARN MACRO
OFF ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
MENU
CHAPTER
PAUSESTOPPOWER
REC
HALL 1
EX/ES
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
MUTE
VOLUME
STEREO
TV INPUT
TV VOL
CH
PRESET
DISC
PARAMETER
SET MENU
EFFECT
LEVEL
ON SCREEN
TESTSLEEP
TV MUTE
MUSIC
VIDEO
TV
THEATER
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
CHP/INDEX
A/B/C/D/E
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
+
ENTER
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
POWER
1
5
9
6
10
0
10
100
11 12
78
234
+
+
1
2
3
4
5
6
7
0
w
e
r
t
9
8
q
y
u
i
o
p
d
g
f
s
j
k
h
a
l
Remote Control
This section describes the controls and their functions of
the remote control. See REMOTE CONTROL
FEATURES on pages 46 to 59 for operating other
components with this remote control.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 RE-NAME
Used for changing the input source name in the display
window (see page 49).
3 TRANSMIT indicator
Flashes while the remote control is sending signals.
4 STANDBY
Sets this unit in the standby mode.
5 SYSTEM POWER
Turns on the power of this unit.
6 Display window
Shows the selected source component that you are
controlling.
7 SOURCE SELECT k/n
Selects the another component to control independently
from the input that has been selected by pressing an input
selector button.
8 LIGHT
Turn the light on or off. When you press this button once,
the light turns on for about ten seconds. Press again to
turn off the light.
9 10KEY/DSP
Selects the numeric button (10KEY) mode or DSP mode.
0 Operation buttons
Provides functions such as play, stop, skip, etc. for
operating your other components selected by the input
selector buttons.
q EX/ES
Turns on or off the Dolby Digital EX or DTS ES decoder
with 10 KEY/DSP set to the DSP position.
w LEVEL
Selects the effect speaker channel to be adjusted and sets
the level.
e ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
r SLEEP
Sets the sleep timer.
t TEST
Outputs the test tone to adjust the speaker levels.
y CLEAR
Used for clearing functions acquired when using the learn
and rename features, and set manufacturer codes (see
pages 52 and 53).
u LEARN
Used for setting up the manufacturer code or for
programming the functions of other remote controls (see
pages 47 to 49).
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM6
7
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
BASS
VOLUME
VIDEO AUX
SILENT
PROGRAM
STEREO
REC OUT
/ZONE 2
SPEAKERS
INPUT
MODE
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET
/
TUNING
PHONES
EFFECT
SOURCE
/REMOTE
MD/TAPE
CDR
TUNER
CD
PHONO
DVD
DTV/LD
CBL/SAT
VCR 1
VAUX
VCR2
/DVR
A/B/C/D/E
S VIDEO
MEMORY
FM/AM
EDIT
PRESET
/TUNING
MAN'L/AUTO FM AUTO/MAN'L MONO
TUNING
MODE
VIDEO AUDIO OPTICALLR
STANDBY
/
ON
NATURAL SOUND AV RECEIVER RX-V3300
TREBLE
+
+
6CH
INPUT
AB
DIGITAL
30°30°
Approximately 6 m (20 feet)
i MACRO
Used to program a series of operations for control by a
single button (see pages 51 and 52).
o MACRO ON/OFF
Turns the macro function on and off.
p Å and ı
Switch the control area for the extra components that are
not connected to this unit without changing the input.
a Input selector buttons
Select the input source and change the control area.
s 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
d DSP program/Numeric buttons
Select DSP programs or numbers according to the
position of 10KEY/DSP.
f MUTE
Mutes the sound. The MUTE indicator turns on when the
MUTE function is on. Press again to restore the audio
output to the previous volume level.
g VOLUME +/
Increases or decreases the volume level.
h STEREO/EFFECT
Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are also directed to the main left and
right speakers.
j PARAMETER/SET MENU
Selects the PARAMETER mode or SET MENU mode.
k Cursor buttons k/n//+
Select and adjust DSP program parameters and SET
MENU items according to the position of PARAMETER/
SET MENU.
l Cover
Slides down to use the various setup buttons. Slides up
when these buttons are not being used.
Using the Remote Control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM7
8
CONTROLS AND FUNCTIONS
RL
LCR
RC RR
LFE
VIRTUAL
DTS
Neo
MOVIE TV THEATER
ENTERTAINMENT12
:6
DOLBY DIGITAL
PRO
LOGIC
VCR DVD TUNER CD
PHONO
CD RV AUX
DSP
EX
MATRIXDISCRETE
ES
PCM
1
SILENT
96/24
SP
DIGITAL
VCR2/DVR
CBL
/
SAT
MD
/
TAPE
TV
/
LD
STEREO
TUNED
MEMORY
P. DIRECT
BASS
MUTE VOLUME
SLEEP
AUTO
D
96
K
Hz
/
24bit
PRO LOGIC
/
AB
dB
ft
m
S
qw t yuio p sa
2
145687 90
e r
3
1
DSP
indicator
Lights up when you select a digital sound field program.
2 Decoder indicators
When any of the decoders equipped on this unit
functions, the indicator lights up.
3 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP (see page
34).
4 Input source indicator
Shows the current input source with a cursor.
5 AUTO indicator
Shows that this unit is in the automatic tuning mode.
6 BASS indicator
Lights up while BASS EXTENSION is on.
7 SLEEP indicator
Lights up while the sleep timer is on.
8 MUTE indicator
Lights up while the MUTE function is on.
9 96/24 indicator
Lights up when the DTS 96/24 signal is input to this unit.
0 VOLUME level indicator
Indicates the volume level.
q
PCM
indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
w SILENT indicator
Lights up when headphones are connected with the sound
effect (see SILENT CINEMA DSP on page 34).
e SP A B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
Front Panel Display
r Headphones indicator
Lights up when headphones are connected.
t DSP program indicators
The name of the selected DSP program lights up when
the ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2, TV THEATER or V/DTS SURROUND
DSP program is selected.
y Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
u STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
i TUNED indicator
Lights up when this unit tunes in to a station.
o MEMORY indicator
Flashes to show a station can be stored.
p P. DIRECT
Lights up while PROCESSOR DIRECT is on.
a Input channel indicator
Indicates the channel components of input signals being
received.
s
LFE
indicator
Lights up when the input signal contains the LFE signal.
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM8
9
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
AC OUTLETS
AC IN
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL
INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
CONTROL
OUT
SPEAKERS
TUNER
REMOTE
IN
75
UNBAL.
OUT
1
2
RC-232C
AM
ANT
GND
FM ANT
+12V
15mA
MAX.
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
DVD
MONITOR
OUT
CBL
/SAT
MAIN
IN
OUT
MAIN
ZONE 2 OUT
REAR CENTER
(SURROUND)
CENTER
FRONT
REAR
EFFECT
PRE OUT/MAIN IN
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
SUB
WOOFER
CENTER
REAR
FRONT EFFECT
REAR CENTER
P
B
Y
R
R
R
L
L
R
L
L
R
L
R
L
R
L
R
L
R
L
OPTICAL
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
CBL
/SAT
CD
CD
PHONO
IN
OUT
OUT
ZONE 2 OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
CD
D-TV
/LD
(SURROUND)
COAXIAL
+
+
+
+
+
+
+
+
+
+
+
+
ZONE 2 OUT
MAIN A OR B
CENTER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6MIN./
SPEAKER
6MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
A + B
8MIN./
SPEAKER
:
A
B
1
8
9 0rq
2
3
5
7
6
4
w e
(U.S.A. model)
1 DIGITAL OUTPUT jacks
2 Audio component jacks
See pages 18 and 19 for connection information.
3 Video component jacks
See pages 15 to 17 for connection information.
4 RS-232C
These are control expansion terminals for commercial
use. Consult your dealer for details.
5 Speaker terminals
See pages 12 and 13 for connection information.
6 AC OUTLETS
Use these outlets to supply power to your other A/V
components (see page 22).
7 AC INLET (U.S.A. model only)
Use this inlet to plug in the supplied power cable (see
page 22).
8 DIGITAL INPUT jacks
9 6CH INPUT jacks
See page 21 for connection information.
0 ZONE 2 OUT jacks
See page 75 for details.
q Antenna input terminals
See page 20 for connection information.
w REMOTE IN/OUT jacks
See page 75 for details.
CONTROL OUT jacks
This is a control expansion terminal for commercial use.
e PRE OUT/MAIN IN jacks
See page 21 for connection information.
r IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance (see page 14). Set this unit in the
standby mode before you change the setting of this
switch.
Rear Panel
0102V3300_1-9_EN(UA) 02.7.24, 6:05 PM9
10
SPEAKER SETUP
This unit has been designed to provide the best sound-
field quality with an 8-speaker system, using left and right
main speakers, left and right rear speakers, left and right
front effect speakers and a center and rear center
speakers. If you use different brands of speakers (with
different tonal qualities) in your system, the tone of a
moving human voice and other types of sound may not
shift smoothly. We recommend that you use speakers
from the same manufacturer or speakers with the same
tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). The
front effect speakers are used for the effect sound. If for
some reason it is not practical to use a center speaker, you
can do without it. Best results, however, are obtained with
the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.
PREPARATION
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
CAUTION
Use magnetically shielded speakers. If this type of
speakers still creates the interference with a monitor,
place the speakers away from the monitor.
Speakers to Be Used
0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM10
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Rear center speaker
Place the rear center speaker in the center between the left
and right rear speakers at the same height from the floor
as the rear speakers.
Front effect speakers
Place the front effect speakers about 0.5 - 1 m (1 - 3 feet)
outside the main speakers and in front of the room, facing
slightly inwards, nearly 1.8 m (6 feet) above the floor.
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (6 feet) above the
floor.
Speaker Placement
Refer to the following diagram when you place the speakers.
Main speaker (L)
1.8 m (6 feet)
Rear speaker (L)
Rear center speaker
Rear speaker (R)
Subwoofer
Main speaker (R)
Center speaker
Front effect speaker (R)
Front effect speaker (L)
Note
If you do not use any effect speakers (rear, front effect, center and/or rear center), change the settings of SPEAKER SET items in the
SET MENU to designate the signals to other terminals you connect speakers to.
0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM11
12
SPEAKER SETUP
12
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), + (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage this unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
y
Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
10 mm (3/8)
Red: positive (+)
Black: negative ()
Banana plug
3
1
2
0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM12
13
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
AC OUTLETS
AC IN
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL
INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
CONTROL
OUT
SPEAKERS
TUNER
REMOTE
IN
75
UNBAL.
OUT
1
2
RS-232C
AM
ANT
GND
FM ANT
+12V
15mA
MAX.
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
DVD
MONITOR
OUT
CBL
/SAT
MAIN
IN
OUT
MAIN
ZONE 2 OUT
REAR CENTER
(SURROUND)
CENTER
FRONT
REAR
EFFECT
PRE OUT/MAIN IN
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
SUB
WOOFER
CENTER
REAR
FRONT EFFECT
REAR CENTER
P
B
Y
R
R
R
L
L
R
L
L
R
L
R
L
R
L
R
L
R
L
OPTICAL
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
CBL
/SAT
CD
CD
PHONO
IN
OUT
OUT
ZONE 2 OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
CD
D-TV
/LD
(SURROUND)
COAXIAL
+
+
+
+
+
+
+
+
+
+
+
+
ZONE 2 OUT
MAIN A OR B
CENTER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6MIN./
SPEAKER
6MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
A + B
8MIN./
SPEAKER
:
A
B
Subwoofer
system
Rear Center
speaker
Rear speaker
Center
speaker
(U.S.A. model)
Right
Right Left
Front Effect speaker
Right Left
Left
Main B speaker
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
REAR CENTER SPEAKER terminals
A rear center speaker can be connected to these terminals.
FRONT EFFECT SPEAKERS terminals
A front effect speaker system can be connected to these terminals.
SUBWOOFER jack
When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,
connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or
rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The
LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are
assigned to this jack.
Note
Depending on the settings of 1 SPEAKER SET and 10 LFE LEVEL on the SET MENU, some signals may not be output from
the SUBWOOFER jack.
Right Left
Main A speaker
0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM13
14
SPEAKER SETUP
AC OUTLETS
AC IN
MAIN
(SURROUND)
CENTER
FRONT
REAR
EFFECT
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
L
L
L
L
L
+
+
+
+
+
+
ZONE 2 OUT
MAIN A OR B
CENTER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6MIN./
SPEAKER
6MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
A + B
8MIN./
SPEAKER
:
A
B
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
ZONE 2 OUT
MAIN A OR B
CENTER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
8MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6MIN./
SPEAKER
6MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
4MIN./
SPEAKER
FRONT
REAR
REAR CENTER
:
:
:
:
:
:
A + B
8MIN./
SPEAKER
:
Switch
position
Upper
Lower
Speaker
Zone 2
Front
Effect
Rear
Center
Rear
Center
Main
Zone 2
Front
Effect
Rear
Center
Rear
Center
Main
Impedance level
The impedance of each speaker must be 6 or higher.
The impedance of each speaker must be 6 or higher.
The impedance of each speaker must be 4 or higher.
[Australia model]
The impedance of each speaker must be 6 or higher.
The impedance must be 4 or higher.
The impedance must be 4 or higher.
[Australia model]
The impedance must be 6 or higher.
If you use one set of main speakers, the impedance of
each speaker must be 4 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8 or higher.
The impedance of each speaker must be 8 or higher.
The impedance of each speaker must be 8 or higher.
The impedance of each speaker must be 8 or higher.
The impedance must be 8 or higher.
The impedance must be 8 or higher.
If you use one set of main speakers, the impedance of
each speaker must be 8 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16 or higher.
[U.S.A. model]
The impedance of each speaker must be 8 or higher.
IMPEDANCE SELECTOR switch
IMPEDANCE SELECTOR switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the upper or lower position according to the impedance of the speakers in your system. Be sure to move this
switch only when this unit is in the standby mode.
(U.S.A. model)
0103V3300_10-23_EN(UA) 02.8.21, 6:59 PM14
15
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
y
The signals input through the S VIDEO jacks can be converted
to composite signals inside of this unit and output through the
VIDEO MONITOR OUT jacks on this unit as well.
The signals input through the VIDEO jack on this unit can be
output through the S VIDEO MONITOR OUT jack by setting
“V CONV.” in “13 DISPLAY SET” on the SET MENU to ON
(see page 70).
When signals input through both S VIDEO and VIDEO jacks,
signals input through the S VIDEO jack has priority.
You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using “7 I/O
ASSIGNMENT” on the SET MENU (see page 67 for details).
VIDEO AUX jacks (on the front
panel)
These jacks are used to connect any video input source
such as a game console and a camcorder to this unit.
Before Connecting Components
CAUTION
Never connect this unit and other components to mains
power until all connections between components have
been completed.
Be sure all connections are made correctly, that is to
say L (left) to L, R (right) to R, “+” to “+” and “–” to
“–”. Some components require different connection
methods and have different jack names. Refer to the
operation instructions for each component to be
connected to this unit.
Use commercially available video pin cables when
connecting to the S VIDEO and COMPONENT
VIDEO jacks.
Connecting Video Components
About the video jacks
There are three types of video jacks.
VIDEO jacks transmit composite
signals.
S VIDEO jacks transmit S-video
signals.
S-video signals are separated into
luminance (Y) and color (C) video
signals to achieve high-quality
color reproduction.
COMPONENT VIDEO jacks
transmit component signals.
Component signals are separated
into luminance (Y) and color
difference (P
B, PR) to provide the
best quality in picture
reproduction.
The signal input through these jacks are output through
the MONITOR OUT jacks of the same type.
Make sure to connect the correct jacks of the same type
on your video component and the video monitor.
CONNECTIONS
VIDEO jack
S VIDEO jack
COMPONENT VIDEO jacks
VIDEO AUX
S VIDEO VIDEO AUDIO OPTICALLR
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
COMPONENT VIDEO
PR PB Y
VIDEO
VIDEO
S VIDEO
Game
console or
video camera
0103V3300_10-23_EN(UA) 7/26/02, 5:46 PM15
16
CONNECTIONS
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL
INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
CONTROL
OUT
TUNER
REMOTE
IN
75
UNBAL.
OUT
1
2
RS-232C
AM
ANT
GND
FM ANT
+12V
15mA
MAX.
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
DVD
MONITOR
OUT
CBL
/SAT
MAIN
IN
OUT
PRE OUT/MAI
SUB
WOOFER
REAR
FRONT EFFE
C
REAR CENTER
P
B
Y
R
R
L
L
R
L
R
L
OPTICAL
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
CBL
/SAT
CD
CD
PHONO
IN
OUT
OUT
ZONE 2 OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
CD
D-TV
/LD
(SURROUND)
COAXIAL
V
S
L R
VVC
S S
L R
O
L
S
R
V
C
O
COMPONENT
INPUT
S VIDEO
INPUT
VIDEO
INPUT
S VIDEO
OUTPUT
VIDEO
OUTPUT
AUDIO OUTPUT
COAXIAL OUTPUT
OPTICAL OUTPUT
AUDIO OUTPUT
COMPONENT OUTPUT
VIDEO
OUTPUT
S VIDEO
OUTPUT
V V V
VVV
V
V
V
(U.S.A. model)
indicates S-video cables
indicates video cables
indicates coaxial cables
indicates optical cables
indicates right analog cables
indicates left analog cables
indicates signal direction
TV/digital TV or
LD player
DVD player
Video
monitor
indicates component video cables
0103V3300_10-23_EN(UA) 02.7.24, 6:05 PM16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95

Yamaha RX-V3300 Kullanım kılavuzu

Kategori
Alıcı
Tip
Kullanım kılavuzu