Magmaweld MONOTIG 200ip El kitabı

monoTIG 165ip

monoTIG 200ip

(+90) 444 93 53

magmaweld.com

info@magmaweld.com (+90) 538 927 12 62

USER MANUAL



Magma Mekatronik may modify the information and the images without any prior notice.







FR

RU

TR

EN

DC TIG WELDING INVERTER



POSTE À SOUDER ONDULEUR TIG DC



3monoTIG 165ip / monoTIG 200ip

EN

4monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

1

1.1

1.2

1.3

1.4

1.5

2

2.1

2.2

2.3

2.4

2.5

2.5.1

2.5.2

2.5.3

2.5.4

2.5.5

2.6

3

3.1

3.2

3.3

4

4.1

4.2

4.3

5

5.1

5.2

CONTENTS

SAFETY PRECAUTIONS

TECHNICAL INFORMATION

General Information

Machine Components

Product Label

Technical Data

Accessories

INSTALLATION

Delivery Control

Installation and Operation Recommendations

Mains Plug Connection

Connection to Mains

Connections for TIG Welding

Torch Connections

Gas Connections

Trigger System Socket Connections

Grounding Clamps Connections

Installation of Torch Consumables

Connections for (MMA) Welding

OPERATION

User Interface

TIG Curve

Machine Features

MAINTENANCE AND SERVICE

Maintenance

Troubleshooting

Error Codes

ANNEX

Spare Part List

Connection Diagrams

5

11

12

13

14

15

16

17

18

24

25

26

27

28

30

31

Contents

EN

5monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

Safety Precautions

Be Sure To Follow All Safety Rules In This Manual!

• Safety symbols found in the manual are used to identify potential hazards.

• When any one of the safety symbols are seen in this manual, it must be understood that there is

a risk of injury and the following instructions should be read carefully to avoid potential hazards.

• The possessor of the machine is responsible for preventing unauthorized persons from

accessing the equipment.

• Persons using the machine must be experienced or fully trained in welding / cutting they have to

read the user manual before operation and follow the safety instructions.

Explanation Of Safety

Information

• Read the user manual, the label on the machine and the safety instructions carefully.

• Make sure that the warning labels on the machine are in good condition. Replace missing and

damaged labels.

• Learn how to operate the machine, how to make the checks in a correct manner.

• Use your machine in suitable working environments.

• Improper changes made in your machine will negatively affect the safe operation and its

longevity.

• The manufacturer is not responsible for the consequences resulting from the operation of the

 

Comprehending Safety

Precautions

Explanation Of Safety

Symbols

ATTENTION

Indicates a potentially hazardous situation that could cause injury or damage.

In case if no precaution is taken, it may cause injuries or material losses / damages.

IMPORTANT



DANGER

Indicates a serious danger. In case if not avoided, severe or fatal injuries may occur.

Make certain that the installation procedures comply with national electrical standards



persons.

• Wear dry and sturdy insulated gloves and working apron. Never use wet or damaged gloves and

working aprons.

 

operator must be protective against sparks, splashing and arc radiation.

• Do not work alone. In case of a danger make sure you have someone for help in your working

environment.

• Do not touch the electrode with the bare hand. Do not allow the electrode holder or electrode to

come in contact with any other person or any grounded object.

• Never touch parts that carry electricity.

• Never touch the electrode if you are in contact with the electrode attached to the work surface,

 



 

material that is large enough to cut off the operator’s contact with the work surface.

• Do not connect more than one electrode to the electrode holder.



as practical.

• Check the torch before operating the machine. Make sure the torch and its cables are in good

condition. Always replace a damaged, worn torch.

• Do not touch electrode holders connected to two machines at the same time since double

 

• Keep the machine turned off and disconnect cables when not in use.

• Before repairing the machine, remove all power connections and / or connector plugs or turn

off the machine.

• Be careful when using a long mains cable.

Electric Shocks

May Kill

SAFETY PRECAUTIONS

EN

6monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

Safety Precautions

• Turn off the electric power.



or wires.

• Call for emergency services.



• If the victim is not breathing, Administer cardiopulmonary resuscitation (CPR) immediately

after breaking contact with the electrical source. Continue CPR (cardiac massage) until

breathing starts or until help arrives.



• Treat an electrical burn as a thermal burn by applying sterile, cold (iced) compresses. Prevent

contamination, and cover with a clean, dry dressing.

Procedures for

Electric Shock

Long-term inhalation of fumes and gases released from welding / cutting is very dangerous.

• Keep away from the moving parts.



closed and in locked position.

• Wear metal toe shoes against the possibility of heavy objects falling on to your feet.

• Burning sensations and irritations in the eyes, nose and throat are signs of inadequate

ventilation. In such a case, immediately boost the ventilation of the work area, and if the

problem persists, stop the welding / cutting process completely.



• Use a suitable fume extraction system where welding / cutting works are being carried out. If

necessary, install a system that can expel fumes and gases accumulated in the entire workshop.

 



cadmium, zinc, coated or painted materials, use masks that provide fresh air in addition to the

above precautions.

• If the gas tanks are grouped in a separate zone, ensure that they are well ventilated, keep the

main valves closed when gas cylinders are not in use, pay attention to possible gas leaks.

• Shielding gases such as argon are denser than air and can be inhaled instead of air if used in

 

• Do not perform welding / cutting operations in the presence of chlorinated hydrocarbon vapors

released during lubrication or painting operations.

• Some welded / cut parts require special ventilation. The safety rules of products that require

special ventilation should be read carefully. A suitable gas mask should be worn when

necessary.

Fumes and Gases

May Be Harmful To

Your Health

Moving Parts May

Cause Injuries

Make sure all connections are tight, clean, and dry.

• Keep cables dry, free of oil and grease, and protected from hot metal and sparks.

• Bare wiring can kill. Check all cables frequently for possible damage. If a damaged or an

uninsulated cable is detected, repair or replace it immediately.

• Insulate work clamp when not connected to workpiece to prevent contact with any metal

object.

• Make sure that the grounding of the power line is properly connected.

 

• Use AC output ONLY if required for the welding process.

• If AC output is required, use remote output control if present on unit.

Additional safety precautions are required when any of the following electrically hazardous

conditions are present :

• in damp locations or while wearing wet clothing,

 

• when in cramped positions such as sitting, kneeling, or lying,

• when there is a high risk of unavoidable or accidental contact with the workpiece or ground.

For these conditions, use the following equipment in order presented:

• Semiautomatic DC constant voltage (CV) MIG welding machine,

• DC manual MMA welding machine,



EN

7monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

Safety Precautions

• Performing works such as welding / cutting, surface grinding, and brushing cause sparks and

metal particles to splatter. Wear approved protective work goggles which have edge guards

under the welding masks to prevent sustaining possible injuries.

Sparks and Spattering

Particles May Get

Into Eyes and Cause

Damage

• Do not touch the hot parts with bare hands.

• Wait until the time required for the machine to cool down before working on its parts.

 

 

Hot Parts May Cause

Severe Burns

 

• Protect other naked parts of your body (arms, neck, ears, etc.) with suitable protective clothing

from these rays.



so that people around you will not sustain injuries from arc rays and hot metals.

• This machine is not used for heating of icebound pipes. This operation performed with the

 

Arc Light May Damage

Your Eyes and Skin

• The noise generated by some equipment and operations may damage your hearing ability.

• Wear approved personal ear protective equipment if the noise level is high.

Noise May Cause

Damage To Your

Hearing Ability

• Do not apply welding / cutting operations into completely closed tanks or pipes.

• Before welding to tanks and closed containers, open them, completely empty them, and clean

them. Pay the greatest attention possible to the welding / cutting operations you will perform in

such places.

• Do not weld in tanks and pipes which might have previously contained substances that may

 

• Welding / cutting equipment heats up. For this reason, do not place it on surfaces that could

easily burn or be damaged !

• Do not point the torch towards any part of the body, other persons, or any metal while

unwrapping the welding / cutting wire.

• When welding wire is run manually from the roller especially in thin diameters the wire can slip

out of your hand, like a spring or can cause damage to you or other people around, therefore you

must protect your eyes and face while working on this.

Welding Wires Can

Cause Injuries



explosions.

• Before starting the welding / cutting work, remove these materials form the environment or cover

 

• National and international special rules apply in these areas.

Welding Operations

May Cause Fire and

Explosion

 

extinguishers tubes, water, and sand in easily accessible places.



circuits. Make sure that they are periodically inspected and pay attention that they run reliably.

• Electrical equipment should not be repaired by unauthorized persons.

Errors occurred if failed to do so may result in serious injury or death when using the

equipment.

• The gas circuit elements operate under pressure; explosions may occur as a result of services

provided by unauthorized persons, users may sustain serious injuries.

• It is recommended to perform technical maintenance of the machine and its auxiliary units at

least once a year.

Maintenance Work



Persons To Machines

and Apparatus May

Cause Injuries

EN

8monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

Safety Precautions



operations, accompanied by another person.

• Avoid performing welding / cutting operations in such enclosed areas as much as possible.

• Take all necessary precautions when moving the machine. The areas where the machine to be

transported, parts to be used in transportation and the physical conditions and health of the

person carrying out the transportation works should be suitable for the transportation process.

• Some machines are extremely heavy; therefore, make sure that the necessary environmental

safety measures are taken when changing their places.

• If the machine is to be used on a platform, it must be checked that this platform has suitable load

bearing limits.

• If it is to be transported by means of a haulage vehicle (transport trolley, forklift etc.), make sure

of the durableness of the vehicle, and the connection points (carrying suspenders, straps, bolts,

nuts, wheels, etc.) that connect the machine to this vehicle.

• If the machine will be carried manually, make sure the durableness of the machine apparatuses

(carrying suspenders, straps, etc.) and connections.

• Observe the International Labor Organization’s rules on carriage weights and the transport

regulations in force in your country in order to ensure the necessary transport conditions.



from torches, cables or hoses. Be absolutely sure to carry gas cylinders separately.

• Remove all interconnections before transporting the welding / cutting equipment, each being

separately, lift and transport small ones using its handles, and the big ones from its handling

rings or by using appropriate haulage equipment, such as forklifts.

Welding / Cutting in





Failure To Take

Precautions During

Transport May Cause

Accidents



 

 

 

 

way that they would not tip over for sure.

• Allow operators to easily access settings and connections on the machine.

Falling Parts May

Cause Injuries Improper positioning of the power-supply sources or other equipment can cause serious injury

to persons and physical damage to other objects.

• Allow the machine to cool down according to operation cycle rates.

• Reduce the current or operation cycle rate before starting the welding / cutting again.

• Do not block the fronts of air vents of the machines.



Excessive Use Of The

Machine Causes

Overheating

Excessive Use Of The

Machine Causes

Overheating

• This device is in group 2, class A in EMC tests according to TS EN 55011 standard.

• This class A device is not intended for use in residential areas where electrical power is supplied

 

compatibility due to radio frequency interference transmitted and emitted in such places.

• Make sure that the work area complies with electromagnetic compatibility (EMC).

Electromagnetic interferences during welding / cutting operations may cause undesired effects

on your electronic devices and network; and the effects of these interferences that may occur

during these operations are under the responsibility of the user.

• If there is any interference, to ensure compliance; extra measures may be taken, such as the

use of short cables, use of shielded (armored) cables, transportation of the welding machine to

 

the work area under protection in terms of EMC.

• To avoid possible EMC damage, make sure to perform your welding / cutting operations as far

away from your sensitive electronic devices as possible (100 m).



connected to the low voltage network used in the home, the installer to make the

electrical connection or the person who will use the machine must be aware that

the machine has been connected in such a manner; in this case the responsibility

belongs to the user.

EN

9monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

Safety Precautions

• Ensure that your welding and/or cutting machine has been installed and situated in its place

according to the user manual.



Before installing the welding / cutting equipment, the person in charge of the operation and / or

the user must conduct an inspection of possible electromagnetic interference in the environment.

Aspects indicated below has to be taken into consideration;

a) Other supply cables, control cables, signal and telephone cables, above and below the welding

/ cutting machine and its equipment,

b) Radio and television transmitters and receivers,

c) Computer and other control hardware,

d) Critical safety equipment, e.g. protection of industrial equipment,

e) Medical apparatus for people in the vicinity, e.g. pacemakers and hearing aids,

f) Equipment used for measuring or calibration,

g) Immunity of other equipment in the environment. The user must ensure that the other

equipment in use in the environment is compatible. This may require additional protection

measures.

h) Considering the time during which the welding / cutting operations or other activities take

place during the day, the boundaries of the investigation area can be expanded according to the

size of the building, the structure of the building and other activities that are being performed

in the building.









• The appliance must be connected to the electricity supply in the recommended manner by a

 

 

tube or with an equivalent shielded cable. The housing of the power supply must be connected

and a good electrical contact between these two structures has to be provided.

• The recommended routine maintenance of the appliance must be carried out. All covers on the

body of the machine must be closed and / or locked when the device is in use. Any changes,

other than the standard settings without the written approval of the manufacturer, cannot be

 

possibly occur.



the work area, in a side by side manner. Welding / cutting cables should not be wound in any

way.



machine to pull metal parts on to itself. To avoid this attraction, make sure that the metal

 

interconnected metal materials.

• In cases where the workpiece cannot be connected to the ground due to electrical safety, or

because of its size and position (for example, in building marine vessel bodies or in steel

construction manufacturing), a connection between the workpiece and the grounding may

reduce emissions in some cases, it should be kept in mind that grounding of the workpiece may

cause users to sustain injuries or other electrical equipment in the environment to break down.

In cases where necessary, the workpiece and the grounding connection can be made as a direct

connection, but in some countries where direct connection is not permissible, the connection

can be established using appropriate capacity elements in accordance with local regulations

and ordinances.

• Screening and shielding of other devices and cables in the work area can prevent aliasing

 

applications.

Evaluation Of

Electromagnetic

Suitability Of The

Work Area

Electromagnetic

Interferance

Reduction Methods



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

Electromagnetic Field

(EMF)

EN

10 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

Safety Precautions

• Choose the welding / cutting method and welding machine for the welding work you are to

perform.

• Select the welding / cutting current and/or voltage to match the material and thickness you are

going to weld.

• If you have to wait for a long time before you start your welding / cutting work, turn off the machine

after the fan has cooled it down. Our machines with smart fan control will turn off on their own.

• This device is not domestic waste. It must be directed to recycling within the framework of the

European Union directive and national laws.

• Obtain information from your dealer and authorized persons about the waste management of

your used machines.

Waste Procedure



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

• Welding / cutting and electric cables should not be wrapped around the body of the machine in

any way,

• The body of the machine should not get caught between the welding / cutting cables. The source

cables must be kept away from the body of the machine, both being placed side by side,

• The return cable must be connected to the workpiece as close as possible to the work area,

• The welding / cutting machine should not rest against the power unit, ensconce on it and not

work too close to it,

• Welding / cutting work should not be performed when carrying the wire supply unit or power

unit.

EMF may also disrupt the operation of medical implants (materials placed inside the body), such

as pacemakers. Protective measures should be taken for people who carry medical implants. For



conducted for welders. Risk assessment should be conducted and recommendations should be

made by a medical professional for users who carry medical implants.

• Do not expose the machine to rain, prevent the machine from splashing water or

pressurized steam.

Protection



WARRANTY FORM

Please visit our website www.magmaweld.com/warranty-form/wr for warranty form.

EN

11monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

TECHNICAL INFORMATION

1.1 General Information

1.2 Machine Components

monoTIG 165ip and monoTIG 200ip inverter type Pulse TIG and MMA welding machine. All welding

parameters can be adjusted via the control panel and monitored via digital displays. It is suitable to work



detailed information.) It is fan cooled and thermally protected against overheating.

Figure 1 : Front and Rear View

1- Control Panel 6- Trigger Control Socket

2-7- Supply Cable Inlet

3- Gas Output 8- Fan

4- Adjustment Pot 9- Gas Inlet

5- Welding and Ground Cable Socket (+) 10- On / Off Switch

Technical Information

1

2

3

4

5

679

8

10

EN

12 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

1.3 Product Label

X

U

I

U

IP23

U

S

I



MMA Welding

TIG Welding

Direct Current



Suitable for Operation at Hazardous

Environments

Duty Cycle

Open Circuit Voltage

Rated Welding Current

Mains Voltage and Frequency

Protection Class

Rated Welding Voltage

Rated Power

Rated Mains Current







4 minutes should be kept idle for the machine cool down (zone 2).

Duty Cycle



6 min. 6 min.6 min.4 min. 4 min. 4 min. Time (min.)

Technical Information

EN

13monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

230 230

 

 

 

 

65 65

 

10,6 10,6

521 x 160 x 311 521 x 160 x 311

 

IP23 IP23

1.4 Technical Data

TECHNICAL DATA UNIT



Rated Power (TIG)

Rated Power (MMA)

V

VDC

kVA

ADC

kVA

kg

mm

Rated Welding Current

Tungsten Electrode Diameter Range

Protection Class

Open Circuit Voltage

Welding Electrode Diameter Range

Weight

Welding Current Range

Dimensions (LxWxH)

monoTIG 200ipmonoTIG 165ip

Torch

Gas Regulator

Lava TIG 18W (8 m) Water Cooled TIG Torch

Lava TIG 26 (8 m) Air Cooled TIG Torch

Water Cooled TIG Accessory Set

(Torch + Regulator)

Workpiece Clamp and Cable

Electrode Clamp and Cable

Lava TIG 18W (4 m) Water Cooled TIG Torch

Water Cooling Unit (CSP 40)

TIG Accessory Set Air Cooled

(Torch + Regulator)

Gas Hose

1

Transport Trolley 1

1.5 Accessories

STANDARD ACCESSORIES QTY

QTYOPTIONAL ACCESSORIES

Technical Information

monoTIG 200ipmonoTIG 165ip

7905201603 7905201603

7906201603 7906201603

7110038004 7110038004

7910000510 7910000510

7907000002 7907000002

7110018004 7110018004

7020001004 7020001004

7110038008 7110038008

7110018008 7110018008

7910000100 7910000100

7910000530 7910000530

7910005200 7910005200

monoTIG 200ipmonoTIG 165ip

EN

14 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

INSTALLATION

2.1 Delivery Control

2.2 Installation and Operation Recommendations

Make sure that all the materials you have ordered have been received. If any material is missing or damaged,

contact your place of purchase immediately.

Scope of supply;

• Welding machine and connected mains cable • Workpiece clamp and cable

   

• User manual

In case of a damaged delivery, record a report, take a picture of the damage and report to the transport

company together with a photocopy of the delivery note. If the problem persists, contact the customer service.

Symbols and their meanings on the device

Welding may be dangerous. Proper working conditions should be ensured and necessary

precautions should be taken. Specialists are responsible for the machine and have to be equipped with the

necessary equipment and those who are not relevant should be kept away from the welding area.



in homes, it is essential that the installer or the person who will operate the machine to make the electrical

connection has information on the machine’s connectivity. In this case the responsibility will be assumed

by the person who will perform the installation or by the operator.

The safety symbols and warning notes on the device and in the operating instructions must be observed

and the labels must not be removed.

Grids are intended for ventilation. The openings should not be covered in order to provide good cooling and

no foreign objects should be inserted.

Installation

• For a better performance, place the machine at least 30 cm away from the surrounding objects. Pay attention

to overheating, dust and moisture near the machine.



machine at a lower current or a lower duty cycle.

• Avoid welding outdoors in windy and rainy weather circumstances. If welding is necessary in such cases,

protect the welding area and the welding machine with a curtain and canopy. If you weld indoors, use a

suitable fume extraction system. Use breathing apparatus if there is a risk of inhaling welding fumes and gas

 

• When positioning the machine, make sure that materials such as walls, curtains, panels, etc. do not impede

easy access to the controls and connections of the machine.



machine and this may invalidate the warranty.

• Use the fuse that is compliant with your system.

• Secure the ground cable as close as possible to the welding area.

• Do not allow the welding current to pass through equipment other than the welding cables.

• The welding cables and the mains cable must not be wrapped in the machine housing during operation.

• When the gas cylinder is placed on the machine, immediately fasten the chain to secure the gas cylinder. If you

do not place the gas cylinder on the machine, fasten it to the wall with a chain

EN

15monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

2.3 Mains Plug Connection

2.4 Connection to Mains

2.5 Connections for TIG Welding

2.5.1 Torch Connections

No plug has been connected to the mains cable since there may different types of outlets available in plants,



the grounding cable is present. After connecting the plug to the cable, do not attach it to the outlet at this stage.



connecting the machine to the mains. The plug must be plugged to the outlet once it is observed to be correct.

Turn the coarse on/off switch to position “1” to start the machine. Make sure that the indicators and LEDs on the

control panel are lit and the cooling fan is operating.

• Start the machine with the on/off switch and check whether the LEDs are on and the cooling fan is working.

• Insert the TIG torch’s plug into the negative pole welding socket and tighten it by turning to the right. Attach the

torch trigger connector that came with the machine to the trigger control cables of the torch. Then connect the

connector to the trigger control socket.

• Connect the gas hose of the torch to the gas outlet.

• Water cooling unit is an optional accessory for cooling the water cooled torches in demanding applications.

For your safety, never use the mains cable of the machine without a plug.

When plugging the power plug into the outlet, make sure that the on/off switch is set to “0”.

Check for the correct mains voltage before connecting the machine to the mains.

When plugging the power plug into the outlet, make sure that the power switch is set to “0” in

the turned-off position.

Tungsten Electrode

Diameter (mm)

Recommended TIG

Welding Current

1.6

2.0

2.4







Installation

EN

16 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

Electrode

Diameter

(mm)

Nozzle

Diameter

(mm)

Welding

Current

(ADC)

Gas Flow

(lt/sec)

1.0

1.6

6.3

9.5







• TIG Torch Connection; the trigger should be connected to the control socket with the terminals 1-2 as shown.

• Secure the argon gas cylinder (b) with a chain.

• Use safe high quality regulators (d) and heaters approved by the standards to work safely and achieve the best

results.

• Keep the gas cylinder valve (a) open for a while, so that possible sediment and particles are discharged.

• Connect the gas regulator to the gas cylinder, making sure that the thread on the gas outlet of the gas cylinder

and the nut of the regulator overlap.

• Connect one end of the cylinder hose (e) to the gas regulator and the other end to the gas inlet at the rear of the

machine and turn on the gas cylinder valve.

(c).

• Make sure the connections are free of leakages.

2.5.2 Gas Connections

2.5.3 Trigger Socket Connections

Installation

2.5.4 Grounding Clamps Connections

• Insert the grounding clamps cable plug (a) into the positive terminal

socket and tighten it by turning right.

(b) to

the workpiece as close as possible to the welding area.

a

b

d

c

e

a

b

EN

17monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

2.5.5 Installation of Torch Consumables

• The ceramic gas nozzle (5) and the tungsten electrode (1) must be selected according to the operating current

and the shape of the workpiece. Accordingly, the diameters of the collet (3) and the collet body (4) must match

with the diameter of the tungsten electrode.

• Remove the back cap (2).

• Remove the existing electrode from the collet and match the diameter of the new tungsten electrode.

• Secure the collet to the torch.



Figure 3 : Installation of Torch Consumables

1

3

4

5

Installation

• Start the machine with the on/off switch and check whether the LEDs are on and the cooling fan is working.

• Connect the electrode clamp cable plug (c) and the grounding clamp cable plug (a) to the welding and ground

cable sockets according to the electrode to be used and the polarity recommended by the electrode manufacturer.

(b) to the workpiece as close as possible to

the welding area.

2.6 Connections for MMA Welding

Check for the correct mains voltage before connecting the machine to the mains.

When plugging the power plug into the outlet, make sure that the power switch is set to “0”

in the turned-off position.

Electrode

Diameter “mm”

Recommended Welding Current

Rutile

2.0

2.5

3.25

4.0

















Basic

a

b

c

EN

18 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

1

2 3 4 5 6

8 7

1- TIG Curve

Use the buttons to scroll through the parameters in the TIG curve. The led of the relevant parameter

will light up depending on which parameter is selected.

Start Current







Pre Gas

    

than the arc start. In order to prevent this deformation, you can adjust pre gas timing before

arc. Furthermore, the life of the tungsten tip will be shortened. Initial gas function allows



area before starting welding.

Ramp Time





3.1 User Interface

OPERATION

Operation

EN

19monoTIG 165ip / monoTIG 200ip

www.magmaweld.com USER MANUAL

Main Current

   



Final Gas



means, the life of the tungsten tip is extended by cooling and at the same time the welding



Frequency Amplitude

It is active when the pulse mode is selected. Determines the amplitude ratio between low

current and high current in a pulse cycle. Indicates how long the set high current will







current be 50 A so this indicates that it will operate at 100 A in 1 ms and 50 A in 99 ms

for 100 ms period.

Pulse Frequency

It is active when the pulse mode is selected. In pulse mode it determines the frequency of





is 5 Hz. and will be adjusted according to the workpiece thickness or the user request.

Repair Current







Note

Repair current is only used in 4 trigger modes. By pressing and pulling the trigger, welding

is started. The trigger is pressed again and the repair current value is used during the



current and continue welding process. If you press and pull the trigger shortly, welding

will terminate.

End Ramp Time

When terminating the welding, the transition time from the main welding current to the



Spot Time





Crater Filling (Final Current)

When ending the welding, switches to the end current from the main welding current. In

this current, welding seam is corrected and welding is terminated.

Note



lower than the main current value. The arc starts with the initial current and the main

current will gradually be increased during the set ramp time. This extends the service life

of the tungsten tip and provides a more stable arc start.

Operation

EN

20 monoTIG 165ip / monoTIG 200ip

www.magmaweld.comUSER MANUAL

2- Trigger Modes / Hot Start - Arc Force Selection



TIG modes are selected you can also change Hot Start and Arc Force settings while the electrode

modes are selected.

Ht

Machine provides up to 2 times higher current than main current for easy ignition.





 

• In miliseconds it reduces the amperese to main welding current.



Ar

When welding the electrode, it prevents the arc interruption by increasing the current up

to twice the main welding current in case the arc tends to interrupt.



• Arc Force prevents the electrode from sticking by adjusting the current when the

electrode tends to stick.







current, makes the launch ramp and continues welding in main current.



 



• The initial gas time can be set from 0 sec to 20 sec. Factory default setting is 1 sec.





to the main current.

• The end ramp determines the time from the main current to the end current. The end

 

PrG : Initial Gas Time

I : Welding Current

PoG : Final Gas Time

Press the Trigger Hold the Trigger Pressed Release Trigger

Operation

Sayfa yükleniyor...

Magmaweld MONOTIG 200ip El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Magmaweld MONOTIG 200ip El kitabı

diğer dillerde

İlgili makaleler