Yamaha DGX-650 El kitabı

Owner’s Manual

EN

Keyboard Stand Assembly

For information on assembling the keyboard stand, refer to

the instructions on page 10 of this manual.

Setting UpReferenceAppendix Basic Guide

DGX-650 Owner’s Manual

2

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING:

Do not place this product in a position where anyone could

walk on, trip over, or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use an

extension cord, the minimum wire size for a 25’ cord (or less ) is 18 AWG.

NOTE: The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be dealer

assembled or installed. Please make sure that benches are stable and

any optional fixtures (where applicable) are well secured BEFORE

using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes neces-

sary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

DGX-650 Owner’s Manual

3

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den

ar ansluten till vägguttaget, även om själva apparaten har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt,

sålænge netledningen sidder i en stikkontakt, som er tændt — også

selvom der er slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko

laitetta verkosta.

(standby)

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and

retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not

be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your

national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human

health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or

the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask

for the correct method of disposal.

(weee_eu_en_01)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : Digital Piano

Model Name : DGX-650

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

DGX-650 Owner’s Manual

4

Basic Guide Reference AppendixSetting Up

Setting Up

Special Features ..............................................................5

PRECAUTIONS ...............................................................6

Compatible Format...........................................................8

About Manuals .................................................................9

Included Accessories .......................................................9

Keyboard Stand Assembly 10

Panel Controls and Terminals 14

Front Panel.....................................................................14

Rear Panel .....................................................................15

Setting Up 16

Power Requirements......................................................16

Connecting a Footswitch (SUSTAIN Jack).....................16

Connecting Headphones or External Audio Equipment

(PHONES/OUTPUT Jack) .........................................17

Connecting a Pedal Unit (PEDAL UNIT jack).................18

Connecting a Computer (USB TO HOST terminal)........19

Turning the Power On/Off ..............................................19

Setting the Volume .........................................................20

Auto Power Off Function ................................................20

MAIN Display 21

Basic Controls 22

Basic Guide

Try Playing a Variety of Instrument Voices 23

Selecting a Main Voice...................................................23

Playing the “Grand Piano”..............................................23

Layering Two Voices—Dual Voice.................................24

Playing a Split Voice in the Left Hand area....................24

Using the Metronome .....................................................25

Adding Harmony ............................................................27

Playing Styles 28

Using the Music Database .............................................29

Chords............................................................................30

Using the Smart Chord feature ......................................31

Calling up Optimum Styles for Your Performance

(Style Recommender) ................................................33

Playing Songs and Audio Files 34

Listening to the Overview Demo ....................................34

Playing Back a Song or Audio File.................................35

Fast Forward, Rewind, and Pause .................................36

A-B Repeat.....................................................................36

Turning Each Track On/Off ............................................36

Displaying the Song Score.............................................37

Displaying the Lyrics ......................................................37

Using the Song Lesson Feature 38

Three Types of Song Lesson .........................................38

Practicing with Song Lesson ..........................................38

Making Practice Perfect—Repeat & Learn.....................39

Recording Your Performance 40

Song Recording .............................................................40

Recording to a Specified Track ......................................42

Clearing a User Song.....................................................44

Clearing a Specified Track from a User Song ................44

Audio Recording.............................................................45

Memorizing Your Favorite Panel Settings 46

Memorizing Panel Settings to the Registration Memory

...46

Recalling Panel Settings from the Registration Memory

...47

Playing Audio Files via an External Audio Player 48

Backup Parameters and Initialization 49

Backup Parameters .......................................................49

Initialization ....................................................................49

Reference

Handy Performance Features 50

Selecting a Reverb Type................................................50

Selecting a Chorus Type................................................50

Selecting a DSP Type ....................................................51

Panel Sustain.................................................................52

Pitch Controls—Transpose ............................................52

Pitch Controls—Tuning ..................................................53

Pitch Controls—the PITCH BEND wheel .......................53

Touch Response Sensitivity...........................................54

Selecting an EQ Setting for the Best Sound ..................54

Setting the Output Gain Level........................................55

Speaker On/Off Setting ..................................................55

Intelligent Acoustic Control (IAC) ...................................56

Voice Settings 57

Selecting a Dual Voice ...................................................57

Selecting a Split Voice ...................................................57

Voice Editing ..................................................................57

Style (Auto Accompaniment) Functions 58

Style Variations—Sections.............................................58

Changing the Tempo .....................................................60

Adjusting the Volume of the Style ..................................60

Playing Chords Without Style Playback.........................60

Setting the Split Point.....................................................61

Setting the Chord Fingering ...........................................61

Looking Up Chords Using the Chord Dictionary ............62

Song and Audio Settings 63

Background Music (BGM) Playback ..............................63

Random Playback..........................................................63

Tempo Setting of the Song ............................................64

Song Volume .................................................................64

Audio Volume.................................................................64

Changing the Voice of the Song ....................................65

Specifying the Channel for the Lesson Part...................65

The Functions 66

Function List...................................................................67

USB Flash Memory Operations 70

Connecting a USB Flash Memory..................................71

Formatting a USB Flash Memory...................................72

Saving a Registration Memory to USB Flash Memory...73

Saving a User Song to USB Flash Memory...................74

Converting a User Song to an Audio file........................75

Loading Files from a USB Flash Memory ......................76

Deleting files from a USB Flash Memory .......................77

Deleting User Data from the Instrument.........................77

Appendix

Troubleshooting........................................................... 78

Messages...................................................................... 79

Specifications............................................................... 80

Index.............................................................................. 82

Table of Contents

DGX-650 Owner’s Manual

5

Setting Up

Special Features

Natural Piano Voice Page 23

The DGX-650 features an amazingly realistic piano Voice (“Natural! Grand Piano”; Voice 001) meticulously

sampled from a concert grand piano—fantastic for playing not only classical compositions but also piano pieces

in any style. No matter what instrument settings have been made, you can instantly call up the Piano Voice by sim-

ply pressing the [PORTABLE GRAND] button.

Graded Hammer Standard Keyboard

Thanks to our experience as the world’s leading manufacturer of acoustic pianos, we’ve developed a keyboard

with action that’s virtually indistinguishable from the real thing. Just as on a traditional acoustic piano, the keys of

the lower notes have a heavier touch, while the higher ones are more responsive to lighter playing. The keyboard’s

sensitivity can even be adjusted to match your playing style. This Graded Hammer technology gives the DGX-650

remarkably authentic touch in a lightweight instrument.

Amazingly Realistic and Dynamic Sounds Page 23

Yamaha’s authentic Voices (especially the highly acclaimed Live!, Sweet! and Cool! Voices) deliver incredibly

natural and dynamic sound—with all the nuances of the original instrument, from delicate to powerful.

Play Along with Styles Page 28

The DGX-650 also has complete and fully automatic accompaniment features with the Styles. These Styles pro-

vide the equivalent of a full backing band covering wide variety of genres—from waltz and swing to 8-beat and

euro-trance, plus much more. Select a Style that matches the music you want to play, or experiment with new

Styles to expand your musical horizons. And if it’s difficult to select the right Style from the huge variety avail-

able, use the Style Recommender function, which calls up a list of suggested Styles, based on a sample rhythm

you play. Also, this instrument features a Smart Chord function, allowing you to simply press single keys, and yet

play various chord progressions that authentically match the music genre and key you specify—giving you even

greater enjoyment from the Styles!

Easy Performance with Music Notation Display Page 37

When you play back a Song, the corresponding score is shown on the display. This is a great way to learn how to

read music. If the Song contains lyric and chord data, the lyrics and chords also appear in the score.

USB TO DEVICE Page 70

Connect a USB flash memory device to the USB TO DEVICE terminal on the instrument, and save or load regis-

trations, and User Songs that you’ve created on the instrument, as well as read data from the device, such as MIDI

files or Style files.

Also, Audio files (.wav) stored to USB flash memory can be played back on the instrument. Moreover, you can

record your performance as Audio data to a USB flash memory device. For more on Audio playing and recording,

see pages 34 and 40.

Setting Up

DGX-650 Owner’s Manual

6

Setting Up

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 81) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in

damage to the instrument or even injury.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• When transporting or moving the instrument, always use two or more people.

Attempting to lift the instrument by yourself may damage your back, result in

other injury, or cause damage to the instrument itself.

• Before moving the instrument, remove all connected cables, to prevent damage

to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Use only the stand specified for the instrument. When attaching the stand or rack,

use the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Assembly

Location

DMI-5 1/2

DGX-650 Owner’s Manual

7

Setting Up

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the

desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel.

This could cause physical injury to you or others, damage to the instrument or

other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the

notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise. When you use the instrument along with the application on your iPhone/iPad, we recommend that you set “Airplane Mode” to “ON”

on your iPhone/iPad in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° –

40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the instrument. If water is left, the

wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth.

 Saving data

• Some data items (page 49) are automatically saved as backup data in the internal memory even if you turn the power off. Saved data may be lost due to

malfunction or incorrect operation. Save important data to external device such as a USB flash memory (pages 73–75).

• The recorded Songs are lost when you turn off the power of the instrument without saving. It occurs also when the power is turned off by Auto Power Off

function (page 20). Save the recorded data to the instrument.

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal

use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use

others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and

sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of

copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your

instrument.

• Apple, iPhone, iPod touch and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

DGX-650 Owner’s Manual

8

Setting Up

Compatible Format

GM System Level 1

“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-compati-

ble music data can be accurately played by any GM-compatible tone generator, regardless of

manufacturer. The GM mark is affixed to all software and hardware products that support GM

System Level.

XF

The Yamaha XF format enhances the SMF (Standard MIDI File) standard with greater function-

ality and open-ended expandability for the future. The instrument is capable of displaying lyrics

when an XF file containing lyric data is played.

STYLE FILE

The Style File Format is Yamaha’s original style file format which uses a unique conversion sys-

tem to provide high-quality automatic accompaniment based on a wide range of chord types.

XGlite

As its name implies, “XGlite” is a simplified version of Yamaha’s high-quality XG tone genera-

tion format. Naturally, you can play back any XG song data using an XGlite tone generator. How-

ever, keep in mind that some songs may play back differently compared to the original data, due

to the reduced set of control parameters and effects.

DGX-650 Owner’s Manual

9

Setting Up

About Manuals

This instrument has the following documents and instructional materials.

 Included Documents

Owner’s Manual (this book)

• Setting Up Please read this section first.

• Basic Guide This section explains how to use the basic functions. Refer to this section while

playing the instrument.

• Reference This section explains how to make detailed settings for the various functions of the

instrument.

• Appendix This section includes troubleshooting information and specifications.

Data List

Contains various important preset content lists such as those of Voices, Styles, and Effects.

 Online Materials (from Yamaha Downloads)

MIDI Reference

Contains MIDI related information such as MIDI Data Format and the MIDI Implementation Chart.

MIDI Basics (only in English, French, German and Spanish)

Contains basic explanations about MIDI.

Computer-related Operations

Includes instructions on connecting this instrument to a computer, and operations related to transfer-

ring files and MIDI data.

To obtain these manuals, access the Yamaha Downloads website, select your country, enter “DGX-650” in the

Model Name box, then click [Search].

 Online Material (for Yamaha Online members)

Song Book (only in English, French, German and Spanish)

Contains music scores for the preset Songs (excluding the Over View Demo Song and Songs 1–11) of

this instrument. After completing the user registration at the website below, you can download this

Song Book free of charge.

Yamaha Online Member https://member.yamaha.com/myproduct/regist/

You will need the PRODUCT ID on the sheet “Online Member Product Registration” packaged with this man-

ual in order to fill out the User Registration form.

Included Accessories

• Owner’s Manual (this book)

• Data List

• Keyboard Stand

• Footswitch

• Music Rest

• AC Power Adaptor

*1

• Online Member Product Registration

*2

*1: May not be included depending on your particular locale.

Check with your Yamaha dealer.

*2: The PRODUCT ID on the sheet will be needed when you

fill out the User Registration form.

Yamaha Downloads http://download.yamaha.com/

Insert the music rest

into the slots as shown.

Music Rest

DGX-650 Owner’s Manual

10

Setting Up

Keyboard Stand Assembly

1

The parts shown in the “Assembly Parts” illustration will be used. Follow the assembly

instructions and select the parts as needed.

Read these cautions carefully before you assemble or use the keyboard stand.

These cautions are to promote safe use of the stand and to prevent injury and damage from occurring to you and others. By fol-

lowing these cautions carefully, your keyboard stand will provide you with safe and prolonged use.

• Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the

sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.

• Use the stand after assembly is complete. An uncompleted stand may overturn or the keyboard may drop.

• Always place the stand on a flat, stable surface. Placing the stand on uneven surfaces may cause it to become unstable or over-

turn, the keyboard to drop, or injury.

• Do not use the stand for anything other than its designed purpose. Placing other objects on the stand may result in the object

dropping or the stand overturning.

• Do not apply excessive force to the keyboard as it may cause the stand to overturn or the keyboard to drop.

• Make sure the stand is sturdy and safe, and all screws have been tight and firm before use. If not, the stand may overturn, the

keyboard may drop, or may result in injury to the user.

• To disassemble, reverse the assembly sequence given below.

Have a phillips-head (+) screwdriver of the appropriate size ready.

CAUTION

q Joint connectors

(4 pcs.)

r 6 x 70 mm roundhead

screws (4 pcs.)

t 6 x 30 mm roundhead

screws (4 pcs.)

y 5 x 16 mm roundhead

screws (4 pcs.)

1

Assembly Parts

Back board

Side

boards

Stand

bases

LR

w Metal brackets e 3 x 8 mm roundhead

screws (12 pcs.)

A (1 pc.) B (1 pc.) C (2 pcs.)

Keyboard Stand Assembly

DGX-650 Owner’s Manual

11

Setting Up

2

Attach the metal brackets.

Attach the metal brackets w to the top of the side

boards, using the screws

e as shown.

3

Attach the stand bases.

Insert the joint connectors q into the side boards

as shown. The joint connectors have been installed

properly if you can see the screw head on the con-

nector.

Attach the “L” (Left) and “R” (Right) stand bases

to the bottom of the side boards, using the screws

r. “L” (Left) and “R” (Right) are marked on the

upper surfaces of the stand bases. If you have trou-

ble fastening the screws, use a screwdriver to

rotate the joint connectors so that the connector

holes are aligned with the screw holes on the stand

bases.

2

LR

e 3 x 8 mm

roundhead

screws

w Metal bracket

(C)

w Metal bracket

(A)

w Metal bracket

(B)

w Metal bracket

(C)

e 3 x 8 mm

roundhead

screws

3

q Joint

connectors

r 6 x 70 mm

roundhead screws

“L”

“R”

• If you put the connectors in wrong direction and want to

take them out, tap around the holes on the boards.

NOTE

Keyboard Stand Assembly

DGX-650 Owner’s Manual

12

Setting Up

4

Attach the back board.

Attach the back board, using the screws t. Check

the back-to-front orientation for the side boards.

Make sure the non-colored surface is facing down.

5

Put the keyboard on the stand.

Check the back-to-front orientation for stand, and

carefully place the keyboard on the side boards.

Slowly move the keyboard so that the holes on the

bottom of the keyboard are properly aligned with

the holes on the angle brackets.

4

t 6 x 30 mm roundhead screws

5

At least

10 cm

At least

10 cm

Be sure to place your hands at

least 10 cm from either end of the

keyboard when positioning it.

• Be careful not to drop the back board or touch the

sharp metal fittings.

• If you have purchased an optional pedal unit, attach the

pedal unit before proceeding to the next step. Refer to the

instructions provided with your pedal unit.

• Be careful not to drop the keyboard or to get your fin-

gers caught between the keyboard and the stand

parts.

• Do not hold the keyboard in any position other than

the position shown in the illustration.

CAUTION

NOTE

CAUTION

Keyboard Stand Assembly

DGX-650 Owner’s Manual

13

Setting Up

6

Install the keyboard to the stand.

Fix the keyboard to the angle brackets, using the

screws

y.

Post-assembly checklist

Once you’ve assembled the stand, check the following

points:

• Are there any parts left over?

 If so, read the assembly instructions again and cor-

rect any errors you might have made.

• Is the instrument clear of doors and other movable fix-

tures?

 If not, move the instrument to an appropriate loca-

tion.

• Does the instrument make a rattling noise when you

play it or move it?

 If so, properly tighten all screws.

• Also, if the keyboard makes a creaking noise or seems

unsteady when you play it, refer carefully to the assem-

bly instructions and diagrams and retighten all screws.

6

y 5 x 16 mm

roundhead

screws

DGX-650 Owner’s Manual

14

Setting Up

Panel Controls and Terminals

Front Panel

q [ ] (Standby/On) switch.....................page 19

w [MASTER VOLUME] control ................page 20

e [DEMO/BGM] button .................... pages 34, 63

r [SCORE] button....................................page 37

t [LYRICS] button....................................page 37

y [REC] button........................... pages 40, 42, 45

u LESSON START

[WAITING] button..............................page 39

[YOUR TEMPO] button .....................page 39

[MINUS ONE] button.........................page 39

i [SMART CHORD] button......................page 31

o [STYLE RECOMMENDER] button.......page 33

!0 Song Track

[1]–[5], [A] buttons............................page 36

Lesson

[R] and [L] buttons ...........................page 38

!1 [METRONOME ON/OFF] button ..........page 25

!2 [TEMPO/TAP] button.................... pages 60, 64

!3 SONG/AUDIO

[REPEAT&LEARN] button................page 39

[A-B REPEAT] button........................page 36

[REW] button.....................................page 36

[FF] button.........................................page 36

[PAUSE] button .................................page 36

[START/STOP] button .......................page 35

!4 STYLE

[ACMP ON/OFF] button.................... page 28

[INTRO/ENDING/rit.] button .............page 58

[MAIN/AUTO FILL] button ................page 58

[SYNC STOP] button ........................page 59

[SYNC START] button....................... page 29

[START/STOP] button....................... page 29

!5 REGIST MEMORY

[BANK], [1]–[4] buttons.................... page 46

!6 CATEGORY [

r

] and [

f

] buttons ....... page 22

!7 [EXIT] button ........................................page 21

!8 [EXECUTE] button ...............................page 72

!9 DATA ENTRY

Dial, Number buttons [0]–[9],

[+] and [-] buttons.............................page 22

@0 [FILE CONTROL] button...................... page 72

@1 [FUNCTION] button..............................page 66

@2 [PORTABLE GRAND] button............... page 23

@3 [SONG/AUDIO] button ......................... page 35

@4 [STYLE] button..................................... page 28

@5 [VOICE] button ..................................... page 23

@6 [MUSIC DATABASE] button.................page 29

@7 [SPLIT ON/OFF] button .......................page 24

@8 [DUAL ON/OFF] button........................ page 24

@9 [HARMONY ON/OFF] button ...............page 27

#0 [PITCH BEND] wheel ........................... page 53

#1 USB TO DEVICE terminal............ pages 70, 71

#2 Compatible Formats .............................. page 8

q

w

ert

io

y

!3

!4

!1 !2

!0

u

#2

Front Panel

Song category list Style category list

Panel Controls and Terminals

DGX-650 Owner’s Manual

15

Setting Up

Rear Panel

#3 CONTRAST knob .................................page 21

#4 USB TO HOST terminal................ pages 19, 68

#5 SUSTAIN jack ....................................... page 16

#6 PEDAL UNIT jack .................................page 18

#7 AUX IN jack...........................................page 48

#8 PHONES/OUTPUT jack........................ page 17

#9 DC IN jack ............................................. page 16

!5

!9

!6

!7 !8

@0

@1

@2 @3

@4 @5

@6

@7 @8 @9

#1

#7 #8 #9#6#5#4#3

#0

A-1C0C1C2C3C4C5C6C7

Rear Panel

Voice category list Music Database category listDisplay (page 21)

“Press & Hold” symbol

By holding down one of the buttons having this sym-

bol, you can call up an alternate function, other than

the one called up when simply pressing.

DGX-650 Owner’s Manual

16

Setting Up

Power Requirements

1

Connect the AC power adaptor to the DC

IN jack.

2

Plug the AC power adaptor into an AC

outlet.

Connecting a Footswitch (SUSTAIN Jack)

The sustain function lets you produce a natural sustain

as you play by pressing a footswitch. Plug the sup-

plied footswitch into this jack and use it to switch sus-

tain on and off.

Damper Resonance

This function simulates the sustain sound produced

with the damper pedal on a grand piano. If you want

to use this function, select Voice 001 (page 23), then

press the Footswitch. This function can be turned off

via the FUNCTION display (page 68).

• Use the specified adaptor (page 81) only. Using the wrong

adaptor can result in damage to the instrument or over-

heating.

• Unplug the AC Power Adaptor when not using the instru-

ment, or during electrical storms, to avoid the possibility of

physical injury to you or others, or damage to the instru-

ment or other property.

WARNING

CAUTION

AC outlet

AC power

adaptor

2

1

• Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turn-

ing any components on or off, make sure to set all volume levels to minimum (0). Otherwise, damage to the components, electri-

cal shock, or even permanent hearing loss may occur.

CAUTION

• The sustain function does not affect the Split Voice (page 24).

• Make sure that the footswitch plug is properly connected to

the SUSTAIN jack before turning on the power.

• Do not press the footswitch while turning the power on. Doing

this changes the recognized polarity of the footswitch, result-

ing in reversed footswitch operation.

NOTE

Setting Up

DGX-650 Owner’s Manual

17

Setting Up

Connecting Headphones or External Audio Equipment (PHONES/OUTPUT Jack)

Headphones

Any pair of stereo headphones with a standard stereo

phone plug can be plugged in here for convenient

monitoring. The speakers are automatically shut off

when a plug is inserted into this jack. This setting can

be changed so that speaker sound is always on regard-

less whether a plug is inserted or not (page 55).

External Audio Equipment

The PHONES/OUTPUT jack also functions as an

external output. You can connect the PHONES/OUT-

PUT jack to a keyboard amplifier, stereo system,

mixer, tape recorder, or other line-level audio device

to send the instrument’s output signal to that device.

Optimum setting

Output gain level for this jack is set to a value suitable

for connecting headphones, as the default setting. You

can switch this to the value suitable for connecting an

external audio device. For details on how to switch the

value, see page 55.

Standard

stereo

phone plug

Audio cable

Standard

stereo

phone plug

• Do not use the instrument/device or headphones for a long

period of time at a high or uncomfortable volume level, since

this can cause permanent hearing loss. If you experience any

hearing loss or ringing in the ears, consult a physician.

• When the instrument’s sound is output to an external

device, first turn on the power to the instrument, then to

the external device. Reverse this order when you turn the

power off. If the instrument’s power is automatically turned

off via the Auto Power Off function (page 20), first turn off

the external device, then turn on the power to the instru-

ment then the external device again.

• Do not route the output from the PHONES/OUTPUT jack to

the AUX IN jack. If you make this connection, the signal

input at the AUX IN jack is output from the PHONES/OUT-

PUT jack. These connections could result in a feedback

loop that will make normal performance impossible, and

may even damage both pieces of equipment.

• Use audio cables and adaptor cables having no (zero) resis-

tance.

CAUTION

NOTICE

NOTE

Setting Up

DGX-650 Owner’s Manual

18

Setting Up

Connecting a Pedal Unit (PEDAL UNIT jack)

This jack is for connecting an optional LP-7A/LP-

7AWH pedal unit. When connecting the pedal unit,

make sure to also assemble the unit on the supplied

keyboard stand.

• Make sure that power is off when connecting or disconnect-

ing the pedal.

• This affects only Main/Dual Voices and Harmony sound

(pages 23, 24 and 27).

NOTE

Keyboard

Stand

LP-7A/7AWH

(optional)

Pedal Unit functions

Damper Pedal (Right)

Pressing this pedal will sustain notes longer. Releasing this

pedal immediately stops (damps) any sustained notes. A “half-

pedal” function of this pedal creates partial sustain effects,

depending on how far down you press the pedal. When using

both a footswitch and pedal unit, the last effect applied takes pri-

ority.

Damper Resonance

This function simulates the sustain sound produced with a

damper pedal on a grand piano. This effect is added when

the Damper pedal is pressed for Voice 001. You can turn this

function on or off via the FUNCTION display (page 68).

Sostenuto Pedal (Center)

If you play a note or notes on the keyboard and press the soste-

nuto pedal while the note(s) are held, those notes will sustain as

long as you hold the pedal (as if the damper pedal had been

pressed) but all subsequently played notes will not be sustained.

This makes it possible to sustain a note or notes, for example,

while other notes are played “staccato.”

Soft Pedal (Left)

The soft pedal reduces the volume and slightly changes the tim-

bre of notes played while the pedal is pressed. The soft pedal

will not affect notes that are already playing when it is pressed.

If you press and hold the

damper pedal here, all the

notes shown will be sus-

tained.

If you press and hold the

sostenuto pedal here, only

the notes held at this timing

will be sustained.

Setting Up

DGX-650 Owner’s Manual

19

Setting Up

Connecting a Computer (USB TO HOST terminal)

By connecting a computer to the USB TO HOST terminal, you can transfer data between the instrument and the

computer via MIDI. For details on using a computer with this instrument, refer to “Computer-related Operations”

on the website (page 9).

Turning the Power On/Off

Turn down the MASTER VOLUME control to “MIN”

then press the [ ] (Standby/On) switch to turn on the

power. While playing the keyboard, adjust the MAS-

TER VOLUME control. To turn off the power, press

the [ ] (Standby/On) switch again for a second.

• Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turn-

ing any components on or off, make sure to set all volume levels to minimum (0). Otherwise, damage to the components, electri-

cal shock, or even permanent hearing loss may occur.

CAUTION

USB terminal USB TO HOST terminal

USB cable

Instrument

• Use an AB type USB cable of less than 3 meters. USB 3.0

cables cannot be used.

• The instrument will begin transmission a short time after the

USB connection is made.

• When using a USB cable to connect the instrument to your

computer, make the connection directly without passing

through a USB hub.

• For information on setting up your sequence software, refer to

the owner’s manual of the relevant software.

NOTICE

NOTE

iPhone/iPad Connection

By connecting your iPhone or iPad to the USB TO

HOST terminal of this instrument and using applica-

tions, you can manage your music files more easily and

take advantage various functions. For details on con-

nection, refer to “iPhone/iPad Connection Manual”

downloadable from the website “Yamaha Downloads”

(page 9).

For information about available applications, access the

following page:

http://www.yamaha.com/kbdapps/

• When using a power adaptor, even when the power is off, a

small amount of electricity is still being consumed by the

instrument. When you are not using the instrument for a

long time, make sure to unplug the AC power adaptor from

the wall AC outlet.

CAUTION

Setting Up

DGX-650 Owner’s Manual

20

Setting Up

Setting the Volume

To adjust the volume level of the entire keyboard

sound, use the MASTER VOLUME control located at

the left of the panel. Play the keyboard to actually pro-

duce sound while you adjusting the volume to the

desired level.

Intelligent Acoustic Control (IAC)

IAC is a function which automatically adjusts and

controls the sound quality according to the overall

volume of the instrument. Even when the volume is

low, it permits both low sounds and high sounds to be

clearly heard. For details, refer to page 56.

Auto Power Off Function

To prevent unnecessary power consumption, this

instrument features an Auto Power Off function that

automatically turns the power off if the instrument is

not operated for a specified period of time. The

amount of time that will elapse before the power is

automatically turned off is set by default to 30 min-

utes.

To disable the Auto Power Off function:

Turn off the power, then press the [ ] (Standby/On)

switch to turn on the power while holding down the

lowest key. Make sure to hold down lowest key until a

message appears at the top left of the display after

pressing the power switch.

To set the time that elapses before Auto Power Off

is executed:

Press the [FUNCTION] button, press the CATE-

GORY [r] or [f] button several times until “Auto

Power Off” appears, then select the desired value by

using the dial.

Settings: OFF, 5, 10, 15, 30, 60, 120

Default value: 30

• Adjusting the MASTER VOLUME control also affects the out-

put level of the PHONES/OUTPUT jack.

• Do not use the instrument at a high volume level for a long

period of time, or your hearing may be damaged.

NOTE

CAUTION

• The recorded Song will be lost if the power is automatically

turned off without executing the save operation. Make sure

to save your recorded Song before the power turns off.

• Depending on the instrument status, the power may not

turn off automatically, even after the elapse of the specified

period of time. Always turn off the power manually when

the instrument is not in use.

• When the instrument is not operated for a specified period

of time while connected to an external device such as an

amplifier, speaker or computer, make sure to follow the

instructions in the Owner’s Manual to turn off the power to

the instrument and the connected devices, in order to pro-

tect the devices from damage. If you do not want the

power to turn off automatically when a device is con-

nected, disable Auto Power Off.

NOTICE

Sayfa yükleniyor ...

Yamaha DGX-650 El kitabı

Bu kılavuz için de uygundur

Yamaha DGX-650 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler