HOTPOINT/ARISTON WMF 7081BS EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi
1
GB
English,1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and options, 7
Table of programmes and wash cycles
Wash options
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Precautions and advice, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
WMF 7081
Instructions for use
Türkçe,13
TR
2
GB
Installation
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to
familiarise himself/herself with its operation and features.
! Read these instructions carefully: they contain vital
information relating to the safe installation and operation of
the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during
transportation) and the
rubber washer with the
corresponding spacer,
located on the rear part of
the appliance (see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to
another location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening or
loosening the adjustable front
feet (see figure); the angle
of inclination, measured in
relation to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the inlet hose
by screwing it to a cold
water tap using a 3/4 gas
threaded connection (see
figure).
Before performing the
connection, allow the
water to run freely until it is
perfectly clear.
2. Connect the inlet hose
to the washing machine
by screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part of
the appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the range
of values indicated in the Technical data table (see next
page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drain duct or a wall drain
situated between 65 and
100 cm from the floor;
alternatively, placed it over
the edge of a basin, sink
or tub, fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
• thesocketisearthedandcomplieswithallapplicable
laws;
• thesocketisabletowithstandthemaximumpower
load of the appliance as indicated in the Technical data
table (see opposite);
• thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see opposite);
• thesocketiscompatiblewiththeplugofthewashing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the
electricity socket must remain within easy reach.
! Do not use extension cords or multiple sockets.
65 - 100 cm
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible in the
event that these standards are not observed.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle “Auto Clean” (see “Cleaning
the washing machine”).
Technical data
Model
WMF 7081
Dimensions
width 59.5 cm
height 85 cm
depth 54 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 800 rotations per minute
Test wash cycles
in accordance
with directives
1061/2010 and
1015/2010
programme
;
temperature 60°C;
programme
;
temperature 40°C.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
4
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
TIMER
button
OPTION
button and
indicator light
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION button and indicator light: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION
button : to select the desired
wash intensity.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAY TIMER button: press to set a delayed start for
the selected wash cycle; the delay period appears on the
display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
CHILD LOCK button : to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the control
panel is locked. This means it is possible to prevent wash
cycles from being modified accidentally, especially where
there are children in the home. To deactivate the control
panel lock, press and hold the button for approximately 2
seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Consumption in off-mode: 1 W
Consumption in Left-on: 1 W
CLEANING
ACTION
button
CHILD
LOCK
button
5
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear; if the DELAY TIMER option has
been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the
programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
Select the wash programme: the cycle will be
automatically set to “Normal” as optimised for garments
with an average level of soil (this setting is not applicable
to the “Wool” cycle, which is automatically set to
Delicate”).
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment (4) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central
pivot (see figure pag. 8).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
7
GB
Wash cycles and options
Wash options
Prewash
If this function is selected, the pre-wash cycle will run; this
is useful for removing stubborn stains.
N.B.: put the detergent in the relevant compartment.
! It cannot be used in conjunction with wash cycles 6, 8, 9,
10, 12, 13, 14, , .
Table of programmes and wash cycles
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumption kWh
Total water lt
Cycle dura-
tion
Prewash
Wash
Bleach
Fabric
softener
1
Anti Stain
40° 800
-
4 - - - 180’
2
Whites
60° 800
-
4 - - - 180’
Standard 60°C cotton programme (1)
60°
(Max. 90°)
800
7 71 1,23 58 195’
Standard 40°C cotton programme (2-3)
40° 800
7 71 0,99 82 190’
5
Synthetics: heavily soiled resistant colours.
60° 800
3 44 0,93 47 110’
5
Synthetics (4): lightly soiled resistant colours.
40° 800
3 44 0,57 46 95’
6
Anti allergy
60° 800 -
4 - - - 195’
7
Baby
40° 800
4 - - - 145’
8
Wool: for wool, cashmere, etc.
40° 800 -
-
1,5 - - - 70’
9
Delicates
30° 0 -
-
1 - - - 80’
10
Fast Wash 60’: to refresh normal soiled garments quickly (not
suitable for wool, silk and clothes which require washing by hand).
60° 800 -
-
3,5
71 0,81 40
60’
11
Cotton Standard 2
20° 800
7 - - - 170’
12
Eco Cottons
Cold Water
800 -
-
7 71 0,17 63 80’
13
Eco Synthetics
Cold Water
800 -
-
3 48 0,07 30 70’
14
Eco Fast 30’
Cold Water
800 -
-
3 71 0,04 34 30’
Rinse
- 800 - - -
7 - - - 36’
Spin and Pump out
- 800 - - - - 7 - - - 16’
For all Test Institutes:
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
3) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
4) Long wash cycle for synthetics: set wash cycle 5 with a temperature of 40°C.
8
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertothe
weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Wool: max. 1,5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing
class that is higher than the standard class (A class). When
running the programme, do not mix garments of different
colours. We recommend the use of powder detergent.
Pre-treatment with special additives is recommended if
there are obstinate stains.
Whites: use this cycle 2 to wash white clothes. The
programme is designed to maintain the brightness of white
clothes over time. Use powder detergent for best results.
Anti allergy: use programme 6 to remove major allergens
such as pollen, mites, cat’s and dog’s hair.
Baby: use the special wash cycle 7 to remove the remove
the soiling typically caused by babies, while removing all
traces of detergent from nappies in order to prevent the
delicate skin of babies from suffering allergic reactions. The
cycle has been designed to reduce the amount of bacteria by
using a greater quantity of water and optimising the effect of
special disinfecting additives added to the detergent.
Wool: the “Wool” wash cycle on this Hotpoint-Ariston
machine has been tested and approved by The Woolmark
Company for washing wool garments labelled as hand
washable provided that the garments are washed
according to the instructions on the garment label and
those issued by the manufacturer of this washing machine.
Hotpoint-Ariston is the first washing machine brand to be
approved by The Woolmark Company for Apparel Care-
Platinum for its washing performance and consumption of
energy and water. (M1126)
Delicates: use programme 9 to wash very delicate
garments having strasses or sequins.
To wash silk garments and curtains select the cycle 9 and
set the “Delicate” level from option . We recommend
turning the garments inside out before washing and placing
small items into the special bag for washing delicates. Use
liquid detergent on delicate garments for best results.
Cotton Standard 20° (programme 11) ideal for heavily
soiled cotton loads. The effective performance levels
achieved at cold temperatures, which are comparable to
washing at 40°, are guaranteed by a mechanical action
which operates at varying speed, with repeated and
frequent peaks.
Eco cycles
The Eco Cycles assure energy saving by eliminating the
need of heating water and it’s an advantage both to your
energy bill and the environment! These innovative Eco
programmes (Cottons 12, Synthetics 13 and Fast 30’ 14)
are available for various fabrics and different quantity of
garment; they have been designed to guarantee a high
cleaning action even at low temperature and can be used
for lightly to medium soiled loads. Eco Cycles give the
best results thanks to an intensified wash action, water
optimization and are carried out in the same average time
of a standard cycle. For the best washing results with Eco
Cycles we recommend the usage of a liquid detergent.
M
AX
1
2
4
3
A
B
9
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
Thisapplianceisnotintendedforusebypersons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
•TheEuropeanDirective2002/96/EConWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycle.Thiswilllimit
wear on the hydraulic system inside the washing machine
and help to prevent leaks.
• Unplugthewashingmachinewhencleaningitand
during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponentsofthe
appliance can be cleaned using a soft cloth soaked in
lukewarm soapy water. Do not use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”programme
for its internal parts that must be run with no load in the
drum.
To help the wash cycle you may want to use either the
detergent (i.e. a quantity 10% the quantity specified for
lightly-soiled garments) or special additives to clean the
washing machine. We recommend running a cleaning
programme every 40 wash cycles.
To start the programme press button A for 5 seconds
(see figure).
The programme will start automatically and will run for
about 70 minutes. To stop the cycle press the START/
PAUSE button.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running
water; this operation should
be repeated frequently.
Caring for the door and drum of your
appliance
• Alwaysleavetheportholedoorajarinordertoprevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the pre-
chamber which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
A
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display (e.g.:
F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomake
contact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
TR
13
Türkçe
TR
ÇAMAŞIR MAKİNESİ
İçindekiler
Montaj, 14-15
Ambalajın çıkartılması ve aynı seviyeye getirilmesi
Su ve elektrik bağlantıları
İlk yıkama
Teknik bilgiler
Çamaşır makinesinin tanıtımı, 16-17
Kumanda paneli
Ekran
Bir çamaşır çevriminin çalışlması, 18
Yıkama çevrim ve seçenekleri, 19
Program ve yıkama çevrimi tablosu
Yıkama seçenekleri
Deterjan ve çamaşır, 20
Deterjan dağıtma çekmecesi
Çamaşırın hazırlanması
Özel yıkama çevrimleri
Önlem ve öneriler, 21
Genel güvenlik uyarıları
Atıkların tasye edilmesi
Cam kapağın açılması
Bakım ve onarım, 22
Su ve elektrik kesilmesi
Çamaşır makinesin temizlenmesi
Deterjan haznesinin temizlenmesi
Kapak ve hazne bakımı
Pompanın temizlenmesi
Su besleme hortumunun kontrol edilmesi
Sorun giderme, 23
Teknik Servis, 24
WMF 7081
Kullanma talimatları
14
TR
Montaj
! Bu kitapçığı gerektiği her an danışabilmeniz için özenle
saklayınız. Çamaşır makinesinin satılması, devri veya
nakli durumlarında da, yeni sahibinin faydalanabilmesi
için bu kılavuz makineyle beraber saklanmalıdır.
! Talimatları dikkatlice okuyunuz; montaj, kullanım ve
güvenliğe ilişkin önemli bilgiler içermektedir.
Ambalajın çıkartılması ve aynı seviyeye
getirilmesi
Ambalajdan çıkartılması
1. Çamaşır makinesinin ambalajdan çıkartılması.
2. Çamaşır makinesinin taşıma esnasında hasar
görmemiş olduğunu kontrol ediniz. Hasar görmüş ise
monte etmeyiniz. Satıcıya başvurunuz.
3. Taşıma sırasında arka
tarafta bulunan 4 adet
koruyucu vidayı ve ara
parçasıyla birlikte buradaki
lastiği de çıkartınız
(bakınız şekil).
4. Delikleri ambalajda bulacağınız plastik kapaklarla
kapayınız.
5. Tüm parçaları muhafaza ediniz: çamaşır makinesinin
nakli gerektiği takdirde takılmaları gerekmektedir.
! Ambalajlar çocuk oyuncağı değildir.
Cihazın aynı seviyeye getirilmesi
1. çamaşır makinesini düz ve sert bir zemine yerleştiriniz,
duvar veya mobilyalara dayamayınız.
2. Yerleştirilecek zemin
tam düz değilse çamaşır
makinesinin vidalı ön
ayaklarını sıkarak veya
gevşeterek dengeyi
sağlayınız (bkz. şekil);
eğim açısı, makinenin üst
tezgahına göre 2° den
fazla olmamalıdır.
Sağlıklı bir dengeleme, çamaşır makinesine sağlam bir
duruş kazandıracağı gibi, çalışması esnasındaki sarsıntı,
gürültü ve hareketlilikleri de önleyecektir. Zeminde
moket veya halı olması halinde, ayarı makinenin altında
havalandırma olabilecek şekilde yapınız .
Su ve elektrik bağlantıları
Su besleme hortumunun takılması
1. Tedarik borusunu 3/4
gaz vidalý baðlantý kullanar-
ak bir soðuk su musluðuna
baðlayýn (bkz. þekil).
Baðlantýyý yapmadan önce,
suyu berraklaþana kadar
akýtýnýz.
2. Su besleme hortumunu
arka kısımının üst sağ
köşesinde bulunan su
girişine vidalayarak
makineye bağlayınız (bkz.
şekil).
3. Hortumda katlanma ve ezilme olmamasına dikkat
ediniz.
! Musluğun su basıncının Teknik Veriler tabelasında
belirtildiği gibi olması gerekir (bkz. yan sayfa).
! Besleme hortumunun boyu yetersizse yetkili bir satıcı
mağaza veya teknisyene başvurunuz.
! Kesinlikle daha önceden kullanılmış hortum
kullanmayınız.
! Makine ile birlikte verilen hortumları kullanınız.
TR
15
Tahliye hortumunun bağlanması
Tahliye hortumunu
bükmeden zeminden 65
ila 100 cm yukarıda yer
alan pis su borusuna
veya duvar tahliyesine
bağlayın;
Buna alternatif olarak,
makine ile birlikte
verilen pis su borusunu
musluğa (şekle bakınız)
bağlayarak lavabo
veya küvetin kenarına
yerleştirin. Hortumun
serbest kalan ucu suya
daldırılmamalıdır.
! Hortum eklerinin kullanı önermiyoruz; kesinlikle
gerekliyse ek hortum orijinal hortum ile aynı çapta olmalı
ve uzunluğu 150 cm. aşmamalıdır.
Elektrik bağlantıları
Cihazı elektrik prizine takmadan önce, aşağıdakilerden
emin olun:
• Prizin topraklandıgından ve ilgili mevzuata uygun
oldugundan;
• Prizin teknik veri tablosunda sterilmekte olan maksimum
cihaz elektrik küne dayanıp dayanamayacagından
(teknik veri tablosuna bakiniz);
• Güç kaynagı voltajının teknik veri tablosunda gösterilen
degerlere uygun olup olmadigindan (teknik veri tablosuna
bakiniz);
• Elektrik prizinin çamaşır makinesinin şi ile uyumlu olup
olmadığından emin olun. Muhafazalı değilse, priz veya
şi değiştirin.
! Çamaşır makinesi kapalı alan olsa bile, evin dışına
yerleştirilmemelidir. Cihazın yağmur, fırtına ve diğer hava
koşullarına maruz bırakılması son derece tehlikelidir.
! Çamaşır makinesi yerleştirildiğinde, elektrik prizi kolay
ulaşılabilir bir durumda olmalıdır.
! Uzatma kablosu veya çoklu priz kullanmayın.
65 - 100 cm
! Kablo bükülmemeli veya sıkıştırılmamalıdır.
! Güç kablosu ve si sadece yetkili teknisyenler
tarafından degistirilmelidir.
Uyarı! Bu standartlara uyulmaması durumunda sirket
sorumlu tutulamaz.
İlk yıkama
Montajdan sonra, çamaşır koymaksızın deterjanla
OTO TEMİZLE” programı ayarlayarak yıkama yapınız.
Teknik bilgiler
Model WMF 7081
Ölçüler
genişlik 59,5 cm
yükseklik 85 cm
derinlik 54 cm
Kapasite 1 - 7 kg
Elektrik
bağlantıları
makine üstünde takılı olan teknik
veriler plakasına bakınız.
Su bağlantıları
max. su basıncı 1 MPa (10 bar) min.
su basıncı 0,05 MPa (0,5 bar)
tambur kapasitesi 52 litre
Sıkma hızı
maksimum dakikada 800 devire
kadar
1061/2010 ve
1015/2010 sayılı
direktifl ere
göre kontrol
programları
program
; 60°C sıcaklıkta;
program
; 40°C sıcaklıkta.
Bu makina aşağıda belirtilen AB
normlarına uygundur:
- 2004/108/CE (Elektromanyetik Uyum)
- 2002/96/CE
- 2006/95/CE (Alçak gerilim)
16
TR
Çamaşır makinesinin tanıtımı
Kumanda paneli
SİCAKLİK
AYARİ dügmesi
YIKAMA
ÇEVRİMİ
SEÇİCİ DÖNER
DÜĞME
Deterjan çekmecesi
ON/OFFdügmesi
DEVIR
AYARİ
düğmesi
START/PAUSE
düğmesi ve gösterge
lambası
EKRAN
ZAMAN
AYARİ
düğmesi
SEÇİM düğmeleri ve
gösterge lambaları
Deterjan çekmecesi: deterjan ve katkı maddelerini
dagıtmak için kullanılır (“Deterjan ve çamasır”’a bakınız).
ON/OFF düğmesi: makineyi açmak ya da kapatmak
için bu tuşa kısa süreli basınız. Yeşil renkte yanıp sönen
START/PAUSE uyarı lambası makinenin açık olduğunu
gösterir. Makineyi çalışır vaziyetteyken kapatmak için
tuşu daha uzun, yaklaşık 3 saniye, basılı tutmanız
gerekir;hafçe ya da yanlışlıkla basıldığında makine
kapanmaz. Makinenin çalışır vaziyetteyken kapatılması
devrede olan yıkama programını iptal eder.
PROGRAM SEÇME DÜGMESI
Istenilen yıkama çevrimini ayarlamak için kullanılır
(“Program ve yıkama çevrimi tablosu”’na bakınız).
SEÇİM düğmeleri ve gösterge lambaları: mevcut
seçenekleri seçmek için basın. Seçilen seçenek ile ilgili
gösterge ışığı açık kalacaktır.
TEMİZLEME ŞEKLİ
dügmesi: arzu edilen yıkama
yoğunluğunu seçmek için bu tuşa basınız
SİCAKLİK AYARİ düğmesi: sıcaklığı düsürmek veya
tamamen iptal etmek için basın; değer ekranda görünür.
DEVIR AYARİ dügmesi: Devir dügmesi: Sikma hizini
düsürmek veya tamamen iptal etmek için basin; deger
ekranda görünür.
ZAMAN AYARİ düğmesi: seçilen yıkama çevrimi için
bir gecikmeli çalıştırma ayarlamak için basın: gecikme
süresi ekranda belirir.
START/PAUSE düğmesi ve gösterge lambası: yeşil
lamba yavaşça yanıp sönünce istediğiniz yıkama
programını başlatmak için tuşa basınız. Yıkama programı
başladıktan sonra uyarı lambası yanık kalır. Seçilen
bir programın beklemeye alınması için aynı tuşa tekrar
basınız; uyarı lambası turuncu renkte yanıp sönecektir.
Sembol yanık değilse makine kapağı açılabilir.
Yıkama programının kaldığı yerden devam etmesi için
aynı tuşa tekrar basınız.
Ç
OCUK
KILIDI düğmesi : kontrol paneli etkin haline
getirmek için tuşu yaklaşık 2 saniye basılı tutmanız
gerekir. Sembol açık ise; kontrol panelinin kilitli
olduğunu gösterir. Böylece özellikle çocuklarınız varsa
programın yanlışlıkla değiştirilmesi engellenir. kontrol
panelini etkisiz haline getirmek için tuşu yaklaşık 2
saniye basılı tutmanız gerekir.
Bekleme modu
Yeni enerji tasarrufu düzenlemeleri ile uyumlu bu çamaşır
makinesine herhangi bir faaliyet algılanmadığında 30
dakika içinde devreye sokulan otomatik bekleme sistemi
yerleştirilmiştir ON/OFF düğmesine bir süre basın ve
makinenin tekrar çalışmasını bekleyin.
Off-mode’da tüketim: 1 W
Left-on’da tüketim: 1 W
Ç
OCUK
KILIDI
düğmesi
TEMİZLEME
ŞEKLİ
düğmesi
TR
17
Ekran
Ekran makineyi programlarken çok yardımcı olur ve faydalı bilgiler sağlar.
Mevcut olan farklı programların süresi ve devre başladığı zaman aynı devrenin sonunda kalan süre görüntülenir; ZAMAN
AYARİ seçeneği ayarlanmışsa, seçili programın başlangıcı için geri sayım görünecektir.
Ilgili dügmeye basılması ayarlı yıkama çevrimi sırasında makine tarafından ulasılan maksimum sıkma hızını ve sıcaklık
degerlerini veya ayarlı yıkama çevrimi ile uyumlu ise en son seçilen degerleri görüntülemenize izin verir.
KAPI KİLİTLİ gösterge lambası:
Yanan sembol kapagın kilitli oldugunu gösterir. Makinenin hasar görmesini önlemek için, kapagı açmadan önce sembol
sönene kadar bekleyin.
Bir program çalisirken kapagi açmak için, START/PAUSE düğmesine basın, KAPAK KİLİTLİ sembolü kapalı ise,
kapak açılmayabilir.
18
TR
Bir yıkama çevriminin çalıştırılması
1. MAKİNEYİ AÇIN. düğmesine basın, START/
PAUSE gösterge lambası yeşil renkte yavaş yavaş
yanıp sönecektir.
2. ÇAMAŞIRI YERLEŞTİRİN. Yan kapağıın.
Aşağıdaki sayfada yer alan program ve yıkama
çevrimi tablosunda gösterilen maksimumk değerini
aşmamaya dikkat ederek, çamaşırı yerleştirin.
3. DETERJANI ÖLÇÜP AYIRIN. Deterjan çekmecesini
çekip çıkarın ve deterjanı “Deterjan ve çamasır”’da
tanımlandıgı gibi ilgili bölmelere dökün.
4. KAPAĞI KAPATIN.
5. YIKAMA ÇEVRIMINI SEÇIN. Istenilen yıkama
çevrimini seçmek için YIKAMA ÇEVRIMI SEÇICI
döner dügmeyi kullanın. Sıcaklık ve s hızı her yıkama
çevrimi için ayrı ayrı ayarlıdır, bu degerlerde degisiklik
yapılabilir. Çevrimresi ekranda gösterilecektir.
6. YIKAMA ÇEVRİMİNİ ÖZELLEŞTİRİN. İlgili düğmeleri
kullanın:
Sıcaklık ve/veya dönüş hızını değiştirin.
Makine, seçilen çevrimle uyumlu ise maksimum
sıcaklığı, seçilen çevrim için ayarlı dönüş hızı
değerlerini veya en son kullanılan ayarları otomatik
olarak görüntüler. Sıcaklık, soğuk Yıkama “OFF”
ayarına ulaşana kadar düğmesine basılarak
düşürülebilir. Dönüş hızı, tamamen devre dışı
bırakılana kadar düğmesine basılarak kademe
kademe azaltılabilir “OFF”. Bu düğmelere tekrar
basılırsa, maksimum değerler sıfırlanır.
! İstisna:
programı seçildiğinde sıcaklık derecesi
90°C ye kadar yükseltilebilir.
Gecikmeli çalıştırmanın ayarlanması.
Seçilen çevrim için gecikmeli başlatmayı ayarlamak
amacıyla, gerekli gecikme süresine ulaşana kadar
ilgili düğmeye tekrar tekrar basın. Bu seçenek
etkinleştirildiğinde, sembolü ekranda yanacaktır.
Gecikmeli başlatma ayarını kaldırmak için “OFF”
yazısı ekranda görünene kadar düğmeye basın.
Arzu edilen yıkama yoğunluğunu ayarlayınız.
opsiyonu, çamaşırların kirlilik derecesine göre ve
arzu edilen yıkama yoğunluğunda yıkama işlemini en
uygun hale getirmemize olanak tanır.
Yıkama programını seçiniz, yıkama devri aynı
derecede kirli olan çamaşırlar için en uygun olan
Normal” seviyede otomatik olarak ayarlanır,
(otomatik olarak “Narin” seviyede ayarlanan “Yünlüler”
için geçerli olmayan ayar).
Çok kirli çamaşırlar için cihaz “Yoğun” seviyeye
ulaşana kadar tuşuna basınız. Bu seviye, yıkama
programının başlangıç aşamasında daha çok su ve
daha fazla mekanik hareket kullanılması sayesinde
yüksek verimde yıkama performansı sağlamaktadır ve
en inatçı lekeleri bile ortadan kaldırmaya elverişlidir.
Çamaşır suyu ile ya da çamaşır suyu olmadan
kullanılabilir.
Eğer beyazlatma işlemi gerçekleştirilmek istenir ise
makine ile birlikte verilen ilave hazneyi 4, hazne 1
içine koyunuz. Çamaşır suyu dozajını ayarlarken
orta seviyede gösterilen “max” seviyeyi geçmeyiniz
(bakınız şekil syf. 20).
Az kirli çamaşırlar veya en hassas kumaşlar için
Narin” seviyesine ulaşana kadar tuşuna basınız.
Hassas çamaşırlar için kusursuz yıkama sonuçlarını
garanti etmek için mekanik hareket azaltılacaktır.
Çevrim ayarlarını değiştirin.
Seçimi etkinleştirmek için düğmeye basın, düğmeyle
ilgili gösterge lambası yanacaktır.
Seçimi devre dışı bırakmak için düğmeye tekrar
basın, gösterge lambası kapanacaktır.
! Seçilen seçenek ayarlı yıkama çevirimi ile uyumlu
degilse, gösterge lambası yanıp sönecek ve seçenek
etkinlestirilmeyecektir.
! Seçenekler önerilen yük değerini ve/veya çevrim
süresini etkileyebilir.
7. YIKAMA ÇEVRİMİNİ BAŞLATIN. START/PAUSE
düğmesine basın. İlgili gösterge lambası sürekli yanık
kalacak şekilde yeşil dönecek ve kapak kilitlenecektir
(KAPAK KİLİTLİ sembolü yanacaktır). Bir yıkama
çevrimini yürütüldüğü sırada değiştirmek için, START/
PAUSE düğmesini kullanarak çamaşır makinesini
duraklatın (START/PAUSE gösterge lambası yavaş
yavaş turuncu renkte yanıp sönecektir) ve sonra
istediğiniz çevrimi seçin ve START/PAUSE düğmesine
tekrar basın. Bir çevrim yürütülürken kapağı açmak
için, START/PAUSE düğmesine basın, KAPAK KİLİTLİ
sembolü kapalı ise, kapak açılmayabilir. Yıkama
çevrimini yarıda kesildiği noktadan başlatmak için,
START/PAUSE düğmesine tekrar basın.
8. YIKAMA ÇEVRİMİNİN SONA ERMESİ. Bu durum
END” yazısı ekranda gösterilecektir, KAPAK KİLİTLİ
sembolü kapandığında, kapak açılabilir. Kapağı
açın, çamaşırı boşaltın ve makineyi kapatın.
! Başlamış olan bir yıkama çevrimini iptal etmek
istiyorsanız, düğmesini basılı tutun. Çevrim
durdurulacak ve makine kapanacaktır.
TR
19
Yıkama çevrim ve seçenekleri
Program ve yıkama çevrimi tablosu
Yıkama seçenekleri
Ön yıkama
Bu işlev seçildiğinde en dayanıklı lekeleri çıkarmak için
kullanılan ön yıkama gerçekleştirilir
Not: Mevcut olan hazneye deterjan koyunuz.
! Sonraki programlarda uygulanamaz: 6, 8, 9, 10, 12, 13,
14, , .
Bütün Test merkezleri için:
1) 1061/2010 düzenlemesine uygun test yıkama çevrimi: 60°C sıcaklıkta yıkama çevrimi yi seçin.
Bu devre, orta kirlilikteki pamuklu çamaşırları temizlemek için uygundur ve 60°C’de yıkanabilir çamaşırlar üzerinde kullanılacak, kombine enerji ve su tüketimi
açısından en etkili devredir. Geçerli olan yıkama sıcaklık derecesi, belirtilen sıcaklık derecesinden farklı olabilir.
2) 1061/2010 düzenlemesine uygun test yıkama çevrimi: 40°C sıcaklıkta yıkama çevrimi yi seçin.
Bu devre, orta kirlilikteki pamuklu çamaşırları temizlemek için uygundur ve 40°C’de yıkanabilir çamaşırlar üzerinde kullanılacak, kombine enerji ve su tüketimi
açısından en etkili devredir. Geçerli olan yıkama sıcaklık derecesi, belirtilen sıcaklık derecesinden farklı olabilir.
3) Pamuklular için kısa yıkama çevrimi: 40°C sıcaklıkta yıkama çevrimi yi seçin.
4) Uzun sentetik programı: 40°C sıcaklıkta yıkama çevrimi 5’yi seçin.
Ekran veya kitapçık üzerinde gösterilen devre süresi, standart şartlara göre hesaplanmış tahmini bir süredir. Geçerli olan süre, girişteki sıcaklık derecesi ve suyun
basıncı, ortam sıcaklığı, deterjan miktarı, yük miktarı ve tipi, yükün dengesi, seçilen ilave seçenekler gibi sayısız faktörlere göre değişiklik gösterebilmektedir.
Yıkama
çevrimleri
Yıkama çevrimi açıklaması
Maks.
Sıcak
(°C)
Maks.
Hız
(dev/
dak.)
Deterjan ve katkı
maddeleri
Maks. yük
(kg)
Kalan nem %
Enerji tüketi-
mi kWh
Toplam su lt
Çevrim
süresi
Ön
yıkama
Ana
Yıkama
Çamaşır
suyu
Yumu-
şatıcı
1
Leke Çıkarma
40° 800
-
4 - - - 180’
2
Beyazlar
60° 800
-
4 - - - 180’
60° Standart Pamuklu (1)
60°
(Max. 90°)
800
7 71 1,23 58 195’
40° Standart Pamuklu (2-3)
40° 800
7 71 0,99 82 190’
5
Sentetikler: çok kirlenmiş dayanıklı renkliler.
60° 800
3 44 0,93 47 110’
5
Sentetikler (4): kirlenmiş dayanıklı renkliler.
40° 800
3 44 0,57 46 95’
6
Anti - Alerji
60° 800 -
4 - - - 195’
7
Bebek Programı
40° 800
4 - - - 145’
8
Yünlüler: Yün, kaşmir vs.
40° 800 -
-
1,5 - - - 70’
9
Hassas Çamaşırlar
30° 0 -
-
1 - - - 80’
10
zlıkama: Az kirlenmiş giysileri hemen temizlemek için (elle
kamayı gerektiren yün, ipek ve elbiseler için uygun değildir).
60° 800 -
-
3,5
71 0,81 40
60’
11
20° Standart Pamuklu
20° 800
7 - - - 170’
12
Eco Pamuklu
Soğuk
su
800 -
-
7 71 0,17 63 80’
13
Eco Sentetikler
Soğuk
su
800 -
-
3 48 0,07 30 70’
14
Eco Hızlı Yıkama 30’
Soğuk
su
800 -
-
3 71 0,04 34 30’
Durulama
- 800 - - -
7 - - - 36’
Sıkma + Su Boşaltma
- 800 - - - - 7 - - - 16’
20
TR
Bebek Programı:
Bu program
7
çocuklara ve
bebeklere ait tipik kirleri yok ettiği gibi, bezlerde
deterjan kalmamasını sağlar ve böylece bebeklerin
hassas ciltlerine zarar vermez. Bu program, daha fazla
miktarda su kullanarak ve deterjana ilave edilen özel
hijyen sağlayıcı katkı maddelerinin etkisini optimize
ederek bakteri oranını azaltmak amacına yönelik
tasarlanmıştır
.
Yünluler: bu Hotpoint-Ariston çamaşır makinesinin
“Yünlüler” yıkama devresi, yıkama işlemi giysilerin
etiketi üzerinde aktarılan talimatlara ve elektrikli ev
aletinin üretici rması tarafından verilen talimatlara
riayet ederek gerçekleştirildiği sürece, “elde
yıkanabilir” olarak sınıandırılan yünlü çamaşırların
yıkanması için Woolmark Company tarafından test
edilmiş ve onaylanmıştır. Hotpoint-Ariston, yıkama
performanslarından ve su ve elektrik tüketiminden dolayı
Woolmark Company tarafından Woolmark Apparel Care
- Platinum sertikasını elde eden ilk çamaşır makinesi
markasıdır. (M1126)
Hassas Çamaşılrar: taşlı veya pullu giysiler gibi çok
hassas çamaşırları yıkamak için programını kullanınız 9.
İpekli kumaşları ve perdeleri yıkamak için programı
9 seçiniz ve opsiyonunun “Narin” seviyesini
ayarlayınız.
Çamaşırları yıkamadan önce ters çevirmeniz ve küçük
parçaları hassas çamaşırların yıkanması için kullanılan
özel torba içerisine koymanız önerilir.
Daha iyi sonuçlar elde etmek için hassas çamaşırlara
özel sıvı deterjanın kullanılması önerilir.
20° Standart Pamuklu (
program
11) kirli pamuklu
çamaşırlar için idealdir. 40°’de bir yıkama ile mukayese
edilebilen, soğuk suda da etkili olan performanslar,
yinelenen ve karşılaştırılan en yüksek hız varyasyonu ile
çalışan mekanik bir hareket ile sağlanır.
Eko Programlar
Eco programlar, çevre için bir avantaja ve ekonomik
bir tasarrufa sahip daha az elektrik enerjisi kullanmayı
sağlayarak, düşük sıcaklıklarda etkili yıkama
performansları sunmaktadır.
Eco programlar (Pamuklu 12, Sentetikler 13 ve Hızlı
Yıkama 30’ 14), farklı kumaş türleri ve az kirli çamaşırlar
için oluşturulmuştur.
En iyi sonucu garanti etmek için, sıvı bir deterjan
kullanmanızı öneririz; manşet, yaka ve lekeleri önceden
işleme tabi tutmanız tavsiye edilir.
Yük dengeleme sistemi
Her dönüş çevriminden önce aşırı titreşimi önlemek
ve yükü tek bir yönde dağıtmak için, tambur yıkama
dönüş hızından biraz daha fazla olan bir hızda sürekli
döner. Birkaç denemeden sonra, yük doğru şekilde
dengelenmezse, makine düşük bir dönüş hızında döner.
Yük çok dengesizse, çamaşır makinesi döndürme yerine
dağıtma işlemini uygular. Gelişmiş yük dağılımı ve
dengeyi desteklemek için, küçük ve büyük giysilerin yük
içerisinde karıştırılmasını öneririz.
Deterjan ve çamaşır
Deterjan çekmecesi
Başarılı yıkama sonuçları aynı zamanda doğru miktarda
deterjan kullanımına bağlıdır: çok fazla deterjan ilave
edilmesi daha iyi bir yıkama ile sonuçlanmadığı gibi, cihazın
içerisinde birikir ve çevre kirliliğine katkıda bulunur.
! Beyaz pamuklu çamaşırlar, ön yıkama ve 60°C’den yüksek
sıcaklık derecesi ile yıkamalar için toz deterjan kullanınız.
! Deterjan ambalajı üzerinde aktarılan bilgileri takip ediniz.
! Çok fazla köpük yapacağından çitileme deterjanı
kullanmayın.
Deterjan çekmecesini açın
ve deterjan veya katkı
maddelerini aşağıdaki
şekilde dökün.
Bölüm 1: Ön yıkama
deterjanı (toz)
Deterjanı dökmeden
önce, ilave bölme 4’ün
çıkarıldığından emin olun.
Bölüm 2: Yıkama deterjanı (toz veya sıvı)
Sıvı deterjan kullanılması halinde doğru doz ayarlaması
için makinede gösterilen A kademesini kullanmanız
önerilir. Toz deterjan ile yıkamalarda B kademesini
kullanınız.
Bölüm 3: Katkı maddeleri (yumuşatıcı vs.)
Yumuşatıcı ızgaranın dışına taşmamalıdır.
ilave bölme 4: Çamaşır suyu
Çamaşırın hazırlanması
Çamaşırı aşağıdakilere göre ayırın:
- etiketteki kumaş türü/sembole
- renge: renkli giysileri beyazlardan ayırın.
Bütün cepleri boşaltın ve düğmeleri kontrol edin.
Kuruturken çamaşırın ağırlığına göre listelenen
değerleri aşmayın:
Dayanıklı kumaslar: maks. 7 kg
Sentetik kumaslar: maks. 3 kg
Yün: maks. 1,5 kg
Ipek: maks. 1 kg
Çamaşırınız ağırlığı ne kadardır ?
1 çarşaf 400-500 gr
1 yastık kılıfı 150-200 gr
1 masa örtüsü 400-500 gr
1 bornoz 900-1.200 gr
1 havlu 150-250 gr
Özel yıkama çevrimleri
Leke Çıkarma: Program 1, renkleri solmayan ve çok kirli
çamaşırların yıkanması için uygundur. Program, standart
sınıftan yüksek bir yıkama sınıfını garanti eder (A sınıfı).
Farklı renkteki çamaşırları bu programda yıkamayınız.
Toz deterjan kullanılması ve inatçı lekeler için özel katkı
maddeleri ile ön yıkama yapmanız önerilir.
Beyazlar: beyaz çamaşırları yıkama devresini kullanınız.
Program 2, zaman içinde beyaz parlaklığının korunması
için düşünülmüştür. Daha iyi sonuçlar için, toz deterjanın
kullanılması tavsiye edilir.
Anti-Alerji: Polen, mayt, kedi ve köpek tüyü gibi temel
alerjenleri ortadan kaldırmak için 6 programını kullanınız.
M
AX
1
2
4
3
A
B
1 / 1

HOTPOINT/ARISTON WMF 7081BS EU Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi