Yamaha YST-SW216 El kitabı

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

Printed in Indonesia WG59150

G

YST-SW216

SUBWOOFER SYSTEM

ENCEINTE A CAISSON DE GRAVE

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

000_cv_YST-SW216_G.fm Page 1 Friday, December 2, 2005 12:43 AM

i

Thank you for selecting this YAMAHA subwoofer system.

Please read the following operating precautions before use.

YAMAHA will not be held responsible for any damage and/or

injury caused by not following the cautions below.

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install this unit in a cool, dry, clean place - away from windows,

heat sources, sources of excessive vibration, dust, moisture and

cold. Avoid sources of humming (transformers, motors). To

prevent fire or electrical shock, do not expose this unit to rain or

water.

• Never open the cabinet. If something drops into the set, contact

your dealer.

• The voltage to be used must be the same as that specified on the

rear panel. Using this unit with a higher voltage than specified

is dangerous and may cause a fire and/or electric shock.

• To reduce the risk or fire or electric shock, do not expose this

unit to rain or moisture.

• Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and the

wires connected to other equipments. Never pull the wires

themselves.

• When not planning to use this unit for a long period (ie.,

vacation, etc.), disconnect the AC power plug from the wall

outlet.

• Since this unit has a built-in power amplifier, heat will radiate

from the rear panel. Place the unit apart from the walls, allowing

at least 20 cm of space above, behind and on both sides of the

unit to prevent fire or damage. Furthermore, do not position

with the rear panel facing down on the floor or other surfaces.

• Do not cover the rear panel of this unit with a newspaper, a

tablecloth, a curtain, etc. in order not to obstruct heat radiation.

If the temperature inside the unit rises, it may cause fire,

damage to the unit and/or personal injury.

• Do not place the following objects on this unit:

- Glass, china, small metallic etc.

If glass etc. falls by vibrations and breaks, it may cause bodily

injury.

- A burning candle etc.

If the candle falls by vibrations, it may cause fire and bodily

injury.

- A vessel with water in it

If the vessel falls by vibrations and water spills, it may cause

damage to the speaker, and/or you may get an electric shock.

• Do not place this unit where foreign objects such as water drips

might fall. It might cause a fire, damage to this unit, and/or

personal injury.

• Never put a hand or a foreign object into the YST port located

on the right side of this unit. When moving this unit, do not hold

the port as it might cause personal injury and/or damage to this

unit.

• Never place a fragile object near the YST port of this unit. If the

object falls or drops by the air pressure, it may cause damage to

the unit and/or personal injury.

• Never open the cabinet. It might cause an electric shock since

this unit uses a high voltage. It might also cause personal injury

and/or damage to this unit.

• When using a humidifier, be sure to avoid condensation inside

this unit by allowing enough spaces around this unit or avoiding

excess humidification. Condensation might cause a fire,

damage to this unit, and/or electric shock.

• Super-bass frequencies reproduced by this unit may cause a

turntable to generate a howling sound. In such a case, move this

unit away from the turntable.

• This unit may be damaged if certain sounds are continuously

outputted at high volume level. For example, if 20 Hz-50 Hz

sine waves from a test disc, bass sounds from electronic

instruments, etc. are continuously outputted, or when the stylus

of a turntable touches the surface of a disc, reduce the volume

level to prevent this unit from being damaged.

• If you hear distorted noise (i.e., unnatural, intermittent

“rapping” or “hammering” sounds) coming from this unit,

reduce the volume level. Extremely loud playing of a movie

soundtrack’s low frequency, bass-heavy sounds or similarly

loud popular music passages can damage this speaker system.

• Vibration generated by super-bass frequencies may distort

images on a TV. In such a case, move this unit away from the

TV set.

• Do not attempt to clean this unit with chemical solvents as this

might damage the finish. Use a clean, dry cloth.

• Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the unit is

faulty.

• Install this unit near the wall outlet and where the AC power

plug can be reached easily.

• Secure placement or installation is the owner’s

responsibility. YAMAHA shall not be liable for any

accident caused by improper placement or installation of

speakers.

CAUTION: Read this before operating your unit.

This unit features a magnetically shielded design, but

there is still a chance that placing it too close to a TV set

might impair picture color. Should this happen, move

this unit away from the TV set.

As long as this unit is connected to the AC wall outlet, it

is not disconnected from the AC power source even if

you turn off this unit by POWER.

1

English

SPECIAL INSTRUCTIONS FOR U.K. MODEL

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged

in a live socket outlet.

FEATURES .................................................................... 1

SUPPLIED ACCESSORIES........................................... 1

PLACEMENT ................................................................ 2

CONNECTIONS ........................................................... 3

Connecting to line output (pin jack) terminals of the

amplifier .............................................................. 3

Connecting to speaker output terminals of the

amplifier ............................................................... 5

Connecting to the INPUT 1/OUTPUT terminals

of the subwoofer ......................................................... 7

Plug in the subwoofer to the AC outlet ...................... 7

CONTROLS AND THEIR FUNCTIONS .................... 8

ADJUSTING THE SUBWOOFER

BEFORE USE ............................................................... 9

Frequency characteristics ........................................ 10

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY II ....................................................... 11

TROUBLESHOOTING .............................................. 12

SPECIFICATIONS ...................................................... 13

• This subwoofer system employs Advanced Yamaha

Active Servo Technology II which Yamaha has

developed for reproducing higher quality super-bass

sound. (Refer to page 11 for details on Advanced

Yamaha Active Servo Technology II.) This super-bass

sound adds a more realistic, theater-in-the-home effect

to your stereo system.

• This subwoofer can be easily added to your existing

audio system by connecting to either the speaker

terminals or the line output (pin jack) terminals of the

amplifier.

• The HIGH CUT switch provides you with two positions

(HIGH and LOW) to adjust the tone balance between the

subwoofer and the front speakers.

After unpacking, check that the following parts are

contained.

Non-skid pads (1 set, 4 pieces)

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

VOLTAGE SELECTOR

(For Asia and General models only)

The voltage selector switch on the rear panel of this unit must be set for your local main voltage BEFORE

plugging this unit into the AC main supply. Voltages are 110-120/220-240 V AC, 50/60 Hz.

CONTENTS

1

2

FEATURES

SUPPLIED ACCESSORIES

2

( : subwoofer, : front speaker)

One subwoofer will have a good effect on your audio

system, however, the use of two subwoofers is

recommended to obtain more effect.

If using one subwoofer, it is recommended to place it on

the outside of either the right or the left front speaker. (See

fig. .) If using two subwoofers, it is recommended to

place them on the outside of each front speaker. (See

fig. .) The placement shown in fig. is also possible,

however, if the subwoofer system is placed directly facing

the wall, the bass effect may lessen because the sound from

it and the sound reflected by the wall may cancel out each

other. To prevent this from happening, face the subwoofer

system at an angle as in fig. or .

There may be a case that you cannot obtain enough super-

bass sounds from the subwoofer when listening in the

center of the room. This is because “standing waves” have

been developed between two parallel walls and they cancel

the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It

also may be necessary to break up the parallel surfaces by

placing bookshelves etc. along the walls.

Use the non-skid pads

Put the provided non-skid pads at the four corners on the

bottom of the subwoofer to prevent the subwoofer from

moving by vibrations etc.

PLACEMENT

A

B

C

Note

A

B C

A

B

3

English

Choose one of the following two connecting methods that is more suitable for your audio

system.

■

Choose (pages 3-4) when you want to enjoy 5.1 surround system

■ Choose (pages 5-6) when you want to output the low frequency signals

Caution: Unplug the subwoofer and other audio/video components before making

connections.

• All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the

owner’s manual of your component to be connected to the subwoofer.

• After all connections are completed, plug in the subwoofer and other audio/video components.

• To connect with a YAMAHA DSP amplifier (or AV receiver), connect the SUBWOOFER (or LOW PASS etc.)

terminal on the rear of the DSP amplifier (or AV receiver) to the /MONO INPUT 2 terminal of the subwoofer.

• When connecting the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier, be sure to

connect the /MONO INPUT2 terminal to the “L” side and the INPUT 2 terminal to the “R” side of the SPLIT

SUBWOOFER terminals.

• Some amplifiers have line output terminals labeled PRE OUT. When you connect the subwoofer to the PRE OUT

terminals of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has

only one set of PRE OUT terminals, do not connect the subwoofer to the PRE OUT terminals. Instead, connect the

subwoofer to the speaker output terminals of the amplifier. (Refer to pages 5-6.)

• When connecting to a monaural line output terminal of the amplifier, connect the /MONO INPUT2 terminal.

• When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT

terminals on the rear panel of the subwoofer. If connected, they will not produce sound.

CONNECTIONS

1

2

Notes

Connecting to line output (pin jack) terminals of the amplifier

Notes

1

L

R

L

4

■ Using one subwoofer

■ Using two subwoofers

CONNECTIONS

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

Subwoofer

Amplifier

To AC outlet

Mono pin cable

(not included)

Audio pin cable

(not included)

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

POWER

VOLUME

OUTPUT

TO SPEAKER S

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

Amplifier

To AC outlet To AC outlet

Mono pin cable

(not included)

Subwoofer

Mono pin cable

(not included)

5

English

Select this method if your amplifier has no line output (pin jack) terminal.

If your amplifier has two sets of front speaker output terminals and both terminals can output

sound signals simultaneously.

• Connect one set of front speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and

connect the other set of front speaker output terminals of the amplifier to the front speakers.

• Set the amplifier so that both sets of front speaker output terminals output sound signals simultaneously.

• If your amplifier has only one set of front speaker output terminals, see page 6.

■ Using one subwoofer (with speaker cables)

■ Using two subwoofers (with speaker cables)

CONNECTIONS

Connecting to speaker output terminals of the amplifier

2

Note

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

Amplifier

Right front speaker

Left front speaker

Subwoofer

To AC outlet

Speaker output

terminals

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

Amplifier

Right front speaker

Left front speaker

To AC outlet

Speaker output

terminals

Subwoofer

6

If your amplifier has only one set of front speaker output terminals.

Connect the speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and connect the

OUTPUT terminals of the subwoofer to the front speakers.

■ Using one subwoofer (with speaker cables)

■ Using two subwoofers (with speaker cables)

CONNECTIONS

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

Right front speaker

Left front speaker

Subwoofer

Amplifier

Speaker output

terminals

To AC outlet

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

OUTPUT

TO SPEAKERS

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

Right front speaker

Left front speaker

Subwoofer

Speaker output

terminals

To AC outlet

Amplifier

Subwoofer

7

English

For connection, keep the speaker cables as short as

possible. Do not bundle or roll up the excess part of the

cables. If the connections are faulty, no sound will be heard

from the subwoofer or the speakers, or both of them. Make

sure that the + and – polarity markings of the speaker

cables are observed and set correctly. If these cables are

reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other, because

this could damage the subwoofer or the amplifier, or both of

them.

■ Before connecting

Remove the insulation coating at the extremity of each

speaker cable by twisting the coating off.

■ How to connect:

1 Press and hold the terminal’s tab, as shown in the

figure.

2 Insert the bare wire.

3 Release your finger from the tab to allow it to lock

securely on the cable’s wire end.

4 Test the firmness of the connection by pulling lightly

on the cable at the terminal.

After all connections are completed, plug in the subwoofer

and other audio/video components to the AC outlet.

CONNECTIONS

Connecting to the INPUT 1/OUTPUT

terminals of the subwoofer

Good

No Good

10 mm

(3/8”)

2

1

Note: Do not insert the

insulation coating into

the hole. The sound

may not be produced.

Black: negative (

–

)

Red: positive (+)

Plug in the subwoofer to the AC outlet

To AC outlet

8

1 POWER switch

Press this switch to the ON position to turn on the

power to the subwoofer. When the power of the

subwoofer is on, the power indicator (4) on the rear

panel light up in green. Press this switch again to set it

to OFF position to turn off the power of the subwoofer.

2 OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the front speakers.

Signals from the INPUT 1 terminals are sent to these

terminals.

(Refer to “CONNECTIONS” for details.)

3 VOLUME control

Adjusts the volume level. Turn the control clockwise to

increase the volume, and counterclockwise to decrease

the volume.

4 Power indicator

Light up in green when the power switch (1) is turned

on; turns off when the power switch is turned off.

5 HIGH CUT switch

Selects the high frequency cut off point. Normally, it is

set to LOW, however, you may set to HIGH if

necessary. (Refer to page 9.)

6 INPUT 2 terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

7 INPUT 1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

(Refer to “CONNECTIONS” for details.)

CONTROLS AND THEIR FUNCTIONS

POWER

VOLUME

OUTPUT

TO SPEAKER S

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

OUTPUT

TO SPEAKERS

1

34

7

6

5

2

VOLUME

Subwoofer rear panel

9

English

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer

and the front speakers by following the procedures described below.

1 Set the VOLUME control to minimum (0).

2 Turn on the power of all the other components.

3 Press the POWER switch to the ON position.

* The Power indicator lights up in green.

4 Play a source containing bass signal and adjust the

amplifier’s volume control to the desired listening

level.

5 Set the HIGH CUT switch to the LOW or HIGH

position.

This subwoofer is designed so that the optimum tone

balance between the subwoofer and the front

speakers is obtained when this HIGH CUT switch is

set to the LOW position. The tone balance may

change, however, depending on the room size, the

distance from the subwoofer to the front speakers,

and so on. If necessary, switch it to the HIGH

position.

6 Rotate the VOLUME control gradually to adjust the

volume balance between the subwoofer and the other

speakers.

* Normally, set the control to the level where you can

obtain a little more bass effect than when the

subwoofer is not used. If the desired response cannot

be obtained, adjust the HIGH CUT switch and the

VOLUME control again.

• Once the volume balance between the subwoofer and

the front speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control.

However, if you change the front speakers to others,

you must make this adjustment again.

• For adjusting the VOLUME control, the HIGH CUT

switch, refer to “Frequency characteristics” on page

10.

ADJUSTING THE SUBWOOFER BEFORE USE

POWER

VOLUME

OUTPUT

TO SPEAKER S

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

INPUT

2

OUTPUT

TO SPEAKERS

1,6

5

3

VOLUME

Subwoofer rear panel

Notes

10

The frequency response of this subwoofer

The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer

is combined with a typical front speaker system.

■ EX.1 When combined with a 4” or 6.5” (10 cm or 16 cm) acoustic suspension, 2 way system front

speakers

*This diagram does not depict actual frequency response characteristics accurately.

ADJUSTING THE SUBWOOFER BEFORE USE

Frequency response

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT

HIGH

HIGH CUT

LOW

VOLUME

HIGH LOW

HIGH

CUT

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-SW216

Front speaker

11

English

In 1988, Yamaha brought to the marketplace speaker

systems utilizing YST (Yamaha Active Servo Technology)

to give powerful, high quality bass reproduction. This

technique uses a direct connection between the amplifier

and speaker, allowing accurate signal transmission and

precise speaker control.

As this technology uses speaker units controlled by the

negative impedance drive of the amplifier and resonance

generated between the speaker cabinet volume and port, it

creates more resonant energy (the “air woofer” concept)

than the standard bass reflex method. This allows for bass

reproduction from much smaller cabinets than was

previously possible.

Yamaha’s newly developed Advanced YST II adds many

refinements to Yamaha Active Servo Technology,

allowing better control of the forces driving the amplifier

and speaker. From the amplifier’s point of view, the

speaker impedance changes depending on the sound

frequency. Yamaha developed a new circuit design

combining negative-impedance and constant-current

drives, which provides a more stable performance and

clear bass reproduction without any murkiness.

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II

High-amplitude

bass sound

Port

Cabinet

Advanced impedance

Converter

Active Servo

Processing

Amplifier

Signals of low amplitude

Air woofer

(Helmholtz resonator)

Signals

12

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer

or service center.

TROUBLESHOOTING

Problem Cause What to Do

Power is not supplied even though the

POWER switch is set to the ON

position.

The power plug is not securely

connected.

Connect it securely.

No sound. The volume is set to minimum. Raise the volume up.

Speaker cables are not connected

securely.

Connect them securely.

Sound level is too low. Speaker cables are not connected

correctly.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and

“

–” to “–”.

A source sound with few bass

frequencies is played.

Play a source sound with bass

frequencies.

Set the

HIGH CUT

switch to the

HIGH

position.

It is influenced by standing waves. Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

13

English

Type .....Advanced Yamaha Active Servo Technology II

Driver........................................25 cm (10”) cone woofer

Magnetic shielding type

Output Power .............. 50 W (100 Hz, 5 Ω 10 %T.H.D)

Dynamic Power ............................................ 100 W, 5 Ω

Input Impedance .................................................. 12 KΩ

Frequency Response ............... 25 Hz - 180 Hz (–10 dB)

Input Sensitivity ..................50 mV (100 Hz, 50 W/5 Ω)

Power Supply

U.S.A. and Canada models ............... AC 120V, 60 Hz

U.K. and Europe models .................. AC 230V, 50 Hz

Australia model ................................AC 240V, 50 Hz

Asia and General models

............................... AC 110-120/220-240 V, 50/60 Hz

Power Consumption .............................................. 45 W

Dimensions (W x H x D)

...................................... 340 mm x 340 mm x 385 mm

(13-3/8” x 13-3/8” x 15-5/32”)

Weight ................................................ 11.2 kg (24.7 lbs.)

Please note that all specifications are subject to change

without notice.

SPECIFICATIONS

i

1

Nous vous remercions d’avoir porté votre choix sur ce subwoofer de YAMAHA.

Tenir compte des précautions ci-dessous avant de faire

fonctionner l’appareil. YAMAHA ne saurait être tenue pour

responsable de tout dommage et/ou blessure dûs à un non-respect

des mises en garde ci-dessous.

• Pour garantir les meilleures performances possibles, lire ce

manuel avec attention. Le garder dans un endroit sûr

pour une utilisation ultérieure.

• Installer cette unité dans un endroit frais, sec et propre - loin des

fenêtres, sources de chaleur et d’endroits où les vibrations, la

poussière, l’humidité ou le froid sont importants. Eviter les

sources de bourdonnements (transformateurs, moteurs). Pour

éviter les incendies ou les électrocutions, ne pas exposer cette

unité à la pluie ni à l’humidité.

• Ne jamais ouvrir le boîtier. Si quelque chose tombe dedans,

contacter immédiatement le revendeur.

• La tension à utiliser doit être la même que celle spécifiée sur le

panneau arrière. Utiliser cet appareil avec une plus haute

tension que celle spécifiée est dangereux et peut causer un

incendie et/ou causer une électrocution.

• Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas

exposer cet appareil à la pluie ni à l’humidité.

• Ne pas forcer les commutateurs, les touches ou les câbles de

raccordement. Lors du déplacement de l’appareil, d’abord

débrancher la prise d’alimentation et les câbles le raccordant à

d’autres appareils. Ne jamais tirer sur les cordons.

• Lorsqu on prévoit de ne pas utiliser cet appareil pendant

longtemps (pendant les vacances, par exemple), débrancher le

cordon d’alimentation CA de la prise murale.

• Cet appareil possédant un amplificateur intégré, de la chaleur

sera irradiée par le panneau arrière. Placer l’unité assez loin des

murs, en laissant toujours un espace de 20 cm au moins au-

dessus, au-dessous et des deux côtés de l’unité afin d’éviter les

risques d’incendie et de dommages. Ne pas positionner non plus

cet appareil dos au plancher ou à une autre surface.

• Ne couvrez pas le panneau arrière de cet appareil avec un

journal, une nappe, un rideau, etc. afin de ne pas empêcher la

dissipation de chaleur. Si la température à l’intérieur de cet

appareil augmente, un incendie peut se déclarer et endommager

cet appareil et/ou causer une blessure corporelle.

• Ne jamais placer les objets suivants sur cette unité:

-

Des objets verres, de la vaissille, des petits objets metalliques, etc.

Des blessures pourraient être causées par des débris de verre,

etc. dûs aux vibrations et aux brisures.

- Une bougie allumée, etc.

Si la bougie tombe sous l’effet des vibrations, elle risque de

provoquer un incendie et des blessures corporelles.

- Un récipient contenant de l’eau

Si le récipient tombe sous l’effet des vibrations et que de l’eau

éclabousse l’enceinte, ceci risque de l’endommager

sérieusement, et/ou de provoquer des électrocutions.

• Ne pas mettre cette unité dans les endroits où des corps

étrangers, comme des jets d’eau par exemple, pourraient tomber

dedans. Ceci pourrait causer un incendie, endommager cette

unité, et/ou des blessures corporelles.

• Ne jamais introduire la main ou un corps étranger dans le port

YST situé sur le côté droit de cette unité. Ne jamais attraper

l’unité par l’orifice du port lors des déplacements, car ceci

pourrait causer des blessures corporelles et/ou endommager

l’unité.

• Ne jamais placer un objet fragile à proximité du port YST de

cette unité. Si cet objet venait à chuter en raison de la pression

de l’air, il pourrait endommager l’unité et/ou causer des

blessures corporelles.

• Ne jamais ouvrir le boîtier. Ceci pourrait entraîner des

électrocutions, car cette unité fonctionne sous haute tension.

Ceci pourrait aussi causer des blessures corporelles et/ou

endommager l’unité.

• En utilisant un humidificateur, éviter la condensation à

l’intérieur de l’appareil en libérant la place autour de l’appareil

ou en évitant l’humidification extrême. La condensation peut

causer un feu, des dommages à l’appareil et/ou une

électrocution.

• Les sons de très basse fréquence produits par cet appareil

peuvent provoquer un sifflement sur le tourne-disque. Dans ce

cas, éloigner cet appareil du tourne-disque.

• Cet appareil peut être endommagé si certains sons sont

continuellement émis à un niveau sonore élevé. Par exemple, si

des ondes sinusoïdales de 20 Hz-50 Hz d’un disque d’essai, des

sons de graves d’instruments électroniques, etc. sont émis en

continu ou si la pointe de lecture d’une platine tourne-disque

touche la surface d’un disque, réduire le niveau de volume pour

éviter d’endommager cet appareil.

• Si une distorsion se fait entendre (par exemple des petits coups

secs intermittents ou un “martèlement”) sur cet appareil,

diminuer le niveau sonore. La lecture à très haut volume des

sons de basse ou des sons de basses fréquences de la bande

sonore d’un film, ou de passages de musique pop de forte

intensité, sont susceptibles d’endommager ce système

d’enceintes.

• Des vibrations générées par des fréquences supergraves

risquent de déformer les images sur un téléviseur. Dans ce cas,

éloigner cet appareil du téléviseur.

• Ne pas essayer de nettoyer cette unité avec des diluants

chimiques, ceci endommagerait le fini. Utiliser un chiffon

propre et sec.

• Bien lire la section “RESOLUTION DES PROBLEMES”

concernant les erreurs de fonctionnement communes avant de

conclure que l’unité est défecteuse.

• Installez l’appareil près de la prise secteur et à un endroit tel que

la fiche secteur soit facilement accessible.

• Le propriétaire du système est entièrement responsable du

bon positionnement et de la bonne installation du système.

YAMAHA décline toute responsabilité en cas d’accident

causé par un positionnement ou une installation inadéquats

des enceintes.

ATTENTION: Tenir compte des précautions ci-dessous

avant de faire fonctionner l’appareil.

Même si cette unité dispose d’une conception à

blindage magnétique, il y a un risque possible de

création d’interférences, visibles sur les images en

couleurs si elle est placée à côté d’un téléviseur. Dans ce

cas, éloigner l’unité du téléviseur.

Tant que l’appareil est raccordé à la prise secteur, il

reste connecté au secteur même si vous le mettez hors

tension avec POWER.

1

Français

CARACTERISTIQUES .................................................. 1

ACCESSOIRES FOURNIS ............................................ 1

POSITIONNEMENT ...................................................... 2

BRANCHEMENTS ........................................................ 3

Branchement aux bornes de sortie de ligne

(fiche jack) de l’amplificateur .............................. 3

Branchement aux bornes de sortie d’enceintes

de l’amplificateur .................................................. 5

Branchement aux bornes INPUT1/OUTPUT du

subwoofer .................................................................. 7

Branchement du subwoofer sur une prise CA du

secteur......................................................................... 7

LES COMMANDES ET LEURS FONCTIONS ............ 8

REGLAGE DU SUBWOOFER

AVANT L’UTILISATION ............................................ 9

Caractéristiques de fréquence................................... 10

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY II ....................................................... 11

RESOLUTION DES PROBLEMES ............................ 12

CARACTERISTIQUES TECHNIQUES...................... 13

• Ce subwoofer utilise la technologie Advanced Yamaha

Active Servo Technology II mise au point par Yamaha

pour la reproduction de basses fréquences de meilleure

qualité. (Pour ce qui concerne Advanced Yamaha Active

Servo Technology II, se reporter à la page 11.) Ces

basses fréquences ajoutent un effet réaliste

cinématographique aux sons fournis par une chaîne

stéréo.

• Ce subwoofer peut être facilement ajouté à votre chaîne

actuelle en le raccordant soit aux bornes d’enceintes soit

aux bornes de sortie de ligne (fiche jack) de

l’amplificateur.

• Le sélecteur HIGH-CUT permet de régler l’équilibre du

son entre le caisson de graves et les enceintes avant sur

l’une de deux positions (HIGH ou LOW).

Vérifier que les pièces suivantes sont comprises dans la

boîte lors du déballage.

Tampons anti-dérapage (1 jeu, 4 patins)

VOLTAGE SELECTOR

(Modèle pour l’Asie et modèle général)

Le commutateur de tension situé sur le panneau arrière de l’unité doit être placé dans la position adéquate

AVANT de brancher l’unité dans la prise CA du secteur. Les tensions sont de 110-120/220-240 V CA, 50/60 Hz.

TABLE DES MATIERES

1

2

CARACTERISTIQUES

ACCESSOIRES FOURNIS

2

( : subwoofer, : enceinte avant)

L’utilisation d’un seul subwoofer dans une chaîne donne

déjà de bons résultats, cependant l’utilisation de deux

subwoofers est recommandée pour accroître l’effet du son.

Lorsqu’on utilise un seul subwoofer, il est recommandé de

le placer sur le côté extérieur de l’enceinte principale droite

ou gauche. (Voir la fig. .) Lorsqu’on utilise deux

subwoofers, il est recommandé de les placer sur le côté

extérieur de chacune des enceintes principales. (Voir la fig.

.) Il est également possible de positionner les enceintes

comme indiqué à la fig. ; cependant, si le subwoofer est

placé directement contre le mur, l’effet de basse pourra se

trouver supprimé car le son émis par l’enceinte et le son

renvoyé par le mur s’annuleront mutuellement. Pour éviter

ce problème, placer le subwoofer à angle oblique par

rapport au mur, comme indiqué sur la fig. ou .

Les sons de très basses fréquences du subwoofer peuvent

parfois être trop faiblement perçus à partir d’une position

d’écoute en milieu de pièce. Les ondes renvoyées par deux

murs parallèles peuvent en effet s’annuler mutuellement et

supprimer les sons de basses.

Dans un tel cas, diriger le subwoofer obliquement par

rapport au mur. Il peut être également nécessaire de

modifier le parallélisme des surfaces murales en plaçant

des étagères etc. le long des murs.

Utiliser les tampons anti-dérapage

Mettre les tampons anti-dérapage fournis aux quatre coins

du bas du subwoofer afin d’empêcher le subwoofer de

bouger sous l’effet des vibrations, etc.

POSITIONNEMENT

A

B

C

Remarque

A

B

C

A

B

3

Français

Choisir l’une des deux méthodes suivantes qui convient le plus à votre système audio.

■

Choisir la méthode (pages 3-4) pour obtenir un son d’ambiance sur 5.1

voies

■ Choisir la méthode (pages 5-6) pour que les signaux basses fréquences

Précautions d’usage : Débrancher le subwoofer et les autres composants audio/video avant

d’effectuer les connexions.

• Tous les branchements doivent être effectués correctement, c’est-à-dire entre L (gauche) et L, entre R (droite) et R, entre

“+” et “+” et entre “–” et “–”. Voir aussi le mode d’emploi de chacun des appareils devant être connectés au subwoofer.

• Brancher le subwoofer et les autres composants audio/vidéo après avoir accompli tous les raccordements.

• Pour un branchement avec un amplificateur YAMAHA DSP (ou un récepteur AV), connecter la borne SUBWOOFER

(ou LOW PASS etc.) située à l’arrière de l’amplificateur DSP (ou du récepteur AV) à la borne /MONO INPUT2 du

subwoofer.

• Lorsqu’on raccorde le subwoofer aux bornes SPLIT SUBWOOFER à l’arrière de l’amplificateur DSP, veiller à

raccorder la borne /MONO INPUT2 au côté “L” et les bornes INPUT2 au côté “R” des bornes SPLIT

SUBWOOFER.

• Certains amplificateurs possèdent des bornes de sortie de ligne nommées PRE OUT. Lorsque l’on raccorde le

subwoofer aux bornes PRE OUT de l’amplificateur, veiller à ce que l’amplificateur possède au moins deux jeux de

bornes PRE OUT. Si l’amplificateur ne possède qu’un seul jeu de bornes PRE OUT, ne pas raccorder le subwoofer aux

bornes PRE OUT. Raccorder plutôt le subwoofer aux bornes de sortie d’enceintes de l’amplificateur. (Se reporter aux

pages 5-6.)

• Pour faire un raccordement à une borne de sortie de ligne mono de l’amplificateur, raccorder la borne /MONO

INPUT2 à cette borne.

• Lorsque l’appareil est raccordé aux bornes de sortie de ligne, aucune autre enceinte ne doit être raccordée aux bornes

OUTPUT du panneau arrière du subwoofer. Cette enceinte ne produirait alors aucun son.

BRANCHEMENTS

1

2

Remarques

Branchement aux bornes de sortie de ligne (fiche jack) de l’amplificateur

Remarques

1

L

R

L

4

■ Utilisation avec un seul subwoofer

■ Utilisation de deux subwoofers

BRANCHEMENTS

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

Subwoofer

Amplificateur

Vers une prise CA

Câble de fiche

mono

(non fourni)

Câble de fiche à

broche

(non fourni)

POWER

VOLUME

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

POWER

VOLUME

OUTPUT

TO SPEAKER S

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

ON

OFF

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

HIGH LOW

HIGH

CUT

INPUT 1

FROM AMPLIFIER

Amplificateur

Vers une prise CA Vers une prise CA

Câble de fiche mono

(non fourni)

Câble de fiche

mono

(non fourni)

Subwoofer

Sayfa yükleniyor ...

Yamaha YST-SW216 El kitabı

Yamaha YST-SW216 El kitabı

Diğer dillerde

İlgili Makaleler