Whirlpool IWE 81282 B ECO (EU) Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi
GB
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and options, 7
Table of wash cycles
Wash options
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
IWE 81282
Instructions for use
WASHING MACHINE
Español, 13
ES
Português,25
PT
ΕΛΛΗΝΙΚΑ,37
GR
BG
Türkçe,61
TR
Áúëãàðñêè,49
2
GB
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet (see figure);
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
• thesocketisearthedandcomplieswithallapplicable
laws;
• thesocketisabletowithstandthemaximumpowerload
of the appliance as indicated in the Technical data table
(see opposite);
• thepowersupplyvoltagefallswithinthevaluesindicated
in the Technical data table (see opposite);
• thesocketiscompatiblewiththeplugofthewashing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle 2.
Technical data
Model
IWE 81282
Dimensions
width 59.5 cm
height 85 cm
depth 60 cm
Capacity
from 1 to 8 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connection
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per minute
Energy rated pro-
grammes accor-
ding to regulation
EN 60456
programme 2; temperature 60°C;
using a load of 8 kg.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2002/96/EC
- 2006/95/EC Low Voltage)
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button
: press this briefly to switch the ma-
chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.
WASH CYCLE knob: used to set the desired wash cycle
(see “Table of wash cycles”).
OPTION buttons with indicator light: used to select the
available options. The indicator light corresponding to the
selected option will remain lit.
SPIN button
: press to reduce or completely exclude
the spin cycle - the value is indicated on the display.
TEMPERATURE button
: press to decrease or comple-
tely exclude the temperature: the value will be shown on
the display.
DELAYED START button
: press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
START/PAUSE button
with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an orange colour. If the symbol
is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine
Control panel
TEMPERATURE
Button
Detergent dispenser drawer
OPTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with indicator light
DISPLAY
DELAYED
START
Button
WASH CYCLE
knob
GB
5
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START
option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the
machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected cycle.
The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear
in section B:
Wash
Rinse
Spin
Drain
The icons corresponding to “temperature”
, “Programmed start” and “spin” appear in section C from top to bottom:
If the
symbol lights up, the display will visualise the set “temperature” value.
When a “delayed start” has been set, the
symbol lights up.
If the
symbol lights up, the display will visualise the set “spin” value.
Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED
symbol is switched
off the door may be opened.
B
C
A
6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Set the WASH CYCLE
knob to the desired programme; a temperature and spin
speed is set for each wash cycle; these may be adjusted.
The duration of the cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the
button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the
symbol lights up on the
display. To remove the delayed start option press the
button until the text “OFF” appears on the display.
Modifying the cycle
settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash
and the option will not be activated.
! If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will
flash and only the second option will be activated; the
indicator light corresponding to the enabled option will
remain lit.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol
will
be on). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash slowly
in an orange colour); then select the desired cycle and
press the START/PAUSE button again.
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED
symbol
is switched off the door may be opened. Press the
START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED
symbol switches off the door may be
opened. Open the door, unload the laundry and switch
off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the
button. The cycle will be stopped
and the machine will switch off.
GB
7
Wash cycles and options
Wash options
Selecting this option enables you to suitably adjust drum
rotation, temperature and water to a reduced load of lightly
soiled cotton and synthetic fabrics (refer to the “Table of
wash cycles”). “
” enables you to wash in less time
thereby saving water and electricity. We suggest using a
liquid detergent suitably measured out to the load quantity.
! It cannot be used with the 1, 2, 6, 7, 8, 9, 10, 11, 12, 13,
, , programmes.
The
function saves energy by not heating the
water used to wash your laundry - an advantage both to
the environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.
! It cannot be used with the 1, 6, 7, 9, 11, 12, 13, , ,
programmes.
Table of wash cycles
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
! It cannot be used in conjunction with the 9, ,
programmes.
Mini load
This option is recommended for when the load of laundry
is equal to half, or less than half, of the maximum recom-
mended load (see Table of wash cycles).
! It cannot be used with the 8, 9, 10, 11, 12, 13, ,
programmes.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash
cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Cycle
duration
Pre-
wash
Wash
Fabric
softener
Normal
Mini
Load
Eco
Time
Daily
1
Cotton with prewash: extremely soiled whites. 90° 1200
8 4 -
2
Cotton: heavily soiled whites. 90° 1200 -
8 4 -
2
Cotton (1): heavily soiled whites and resistant colours. 60° 1200 -
8 4 -
2
Cotton (2): lightly soiled whites and delicate colours. 40° 1200 -
8 4 -
3
Cotton: heavily soiled whites and resistant colours. 60° 1200 -
8 4 4
4
Coloured Cottons (3): lightly soiled whites and delicate colours. 40° 1200 -
8 4 4
5
Synthetics: heavily soiled resistant colours. 60° 800 -
3,5 1,5 2,5
Special
6
Wool: for wool, cashmere, etc. 40° 600 -
2 1 -
7
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
2 1 -
8
Jeans
40° 800 -
4 - -
9
Express: to refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800 -
1,5 - -
10
Outwear
30° 400 -
- 2,5 - -
Sport
11
Sport Intensive
30° 600 -
4 - -
12
Sport Light
30° 600 -
4 - -
13
Sport Shoes
30° 600 -
Max.
2 pairs
- -
Partial wash cycles
Rinse - 1200 - -
8 4 -
Spin - 1200 - - - 8 - -
Drain - 0 - - - 8 - -
The duration of the wash cycles can be checked on the display.
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
•Donotexceedthelistedvalues,whichrefertotheweight
of the laundry when dry:
Durable fabrics: max. 8 kg
Synthetic fabrics: max. 3,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 2 kg
Silk: max. 2 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Wool: All wool garments can be washed using programme
6, even those carrying the “hand-wash only”
label. For
best results, use special detergents and do not exceed 2
kg of laundry.
Silk: use special wash cycle 7 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 7.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 8.
Express: this wash cycle was designed to wash lightly
soiled garments quickly: it lasts just 15 minutes and the-
refore saves both energy and time. By selecting this wash
cycle (
9
at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum
load of 1.5 kg.
Outwear (
wash cycle
10): is studied for washing water-
repellent fabrics and winter jackets (e.g. Gore-Tex,
polyester, nylon); for best results, use a liquid detergent
and dosage suitable for a half-load; pre-treat necks,
cuffs and stains if necessary; do not use softeners or
detergents containing softeners. Stuffed duvets cannot
be washed with this programme.
Sport Intensive (
wash cycle
11): is for washing heavily
soiled sports clothing fabrics (tracksuits, shorts, etc.);
for best results, we recommend not exceeding the ma-
ximum load indicated in the “Table of wash cycles”.
Sport Light (
wash cycle
12): is for washing lightly soiled
sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum
load indicated in the “Table of wash cycles”. We recom-
mend using a liquid detergent and dosage suitable for a
half-load.
Sport Shoes (
wash cycle
13): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
GB
9
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
• Thisapplianceisnotintendedforusebypersons(inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that
they do not play with the appliance.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
• Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2002/96/EConWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
3. using a screwdriver, remo-
ve the cover panel on the lo-
wer front part of the washing
machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
10
GB
Cutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycle.Thiswill
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
• Unplugthewashingmachinewhencleaningitanddu-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running wa-
ter; this operation should be
repeated frequently.
Caring for the door and drum of your
appliance
• Alwaysleavetheportholedoorajarinordertoprevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the pre-
chamber which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Care and maintenance
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The option indicator lights and the
start/pause indicator light flash and
an error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Running a wash cycle”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see
“Care and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteand
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
ES
13
Español
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Descripción de la lavadora, 16-17
Panel de control
Pantalla
mo efectuar un ciclo de lavado, 18
Programas y funciones, 19
Tabla de programas
Funciones de lavado
Detergentes y ropa, 20
Contenedor de detergentes
Preparar la ropa
Programas particulares
Sistema de equilibrado de la carga
Precauciones y consejos, 21
Seguridad general
Eliminaciones
Apertura manual de la puerta
Mantenimiento y cuidados, 22
Interrumpir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Anomalías y soluciones, 23
Asistencia, 24
ES
IWE 81282
Manual de instrucciones
LAVADORA
14
ES
! Es importante conservar este manual para poder consul-
tarlo en cualquier momento. En caso de venta, de cesión o
de traslado, verifique que permanezca junto con la lava-
dora para informar al nuevo propietario sobre el funciona-
miento y brindar las correspondientes advertencias.
! Lea atentamente las instrucciones: ellas contienen
importante información sobre la instalación, el uso y la
seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora no haya sufrido daños durante
el transporte. Si estuviera dañada no la conecte y llame al
revendedor.
3. Quite los 4 tornillos de
protección para el transpor-
te y la arandela de goma
con el correspondiente
distanciador ubicados en
la parte posterior (ver la
figura).
4. Cubra los orificios con los tapones de plástico sumini-
strados con el aparato.
5. Conserve todas las piezas: cuando la lavadora deba ser
transportada nuevamente, deberán volver a colocarse.
! Los embalajes no son juguetes para los niños.
Nivelación
1. Instale la lavadora sobre un piso plano y rígido, sin apo-
yarla en las paredes, muebles ni en ningún otro aparato.
2. Si el piso no está perfec-
tamente horizontal, com-
pense las irregularidades
desenroscando o enro-
scando las patas delanteras
(ver la figura); el ángulo de
inclinación medido sobre
la superficie de trabajo, no
debe superar los 2º.
Una cuidadosa nivelación
brinda estabilidad a la máquina y evita vibraciones, ruidos
y desplazamientos durante el funcionamiento. Cuando se
instala sobre moquetas o alfombras, regule los pies para
conservar debajo de la lavadora un espacio suficiente para
la ventilación.
Conexiones hidráulicas y eléctricas
Conexión del tubo de alimentación de agua
1. Conectar el tubo de tubo
enroscándolo a un grifo de
agua fría con la boca rosca-
da de 3/4 gas (ver la figura).
Antes de conectarlo, haga
correr el agua hasta que
esté límpida.
2. Conecte el tubo de
alimentación a la lavadora
enroscándolo en la toma
de agua correspondiente
ubicada en la parte poste-
rior derecha (arriba) (ver la
figura).
3. Controle que en el tubo no hayan pliegues ni estrangu-
laciones.
! La presión de agua del grifo debe estar comprendida
dentro de los valores contenidos en la tabla de Datos
técnicos (ver la página correspondiente).
! Si la longitud del tubo de alimentación no es la suficiente,
diríjase a un negocio especializado o a un técnico autori-
zado.
! No utilice nunca tubos ya usados.
! Utilice los suministrados con la máquina.
Instalación
ES
15
Conexión del tubo de descarga
Conecte el tubo de de-
scarga, sin plegarlo, a una
tubería de descarga o a una
descarga de pared colo-
cadas a una altura del piso
entre 65 y 100 cm;
o apóyelo en el borde
de un lavamanos o de
una bañera, uniendo la
guía suministrada con el
aparato, al grifo (ver la
figura). El extremo libre del
tubo de descarga no debe
permanecer sumergido en
el agua.
! No se aconseja utilizar tubos de prolongación, si fuera in-
dispensable hacerlo, la prolongación debe tener el mismo
diámetro del tubo original y no superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
• latomatengalaconexiónatierrayhayasidohecha
según las normas legales;
• latomaseacapazdesoportarlacargamáximade
potencia de la máquina indicada en la tabla de Datos
técnicos (ver al costado);
• latensióndealimentaciónestécomprendidadentrode
los valores indicados en la tabla de Datos técnicos (ver
al costado);
• latomaseacompatibleconelenchufedelalavadora.Si
no es así, sustituya la toma o el enchufe.
! La lavadora no debe ser instalada al aire libre, ni siquiera
si el lugar está reparado, ya que es muy peligroso dejarla
expuesta a la lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de corriente debe
ser fácilmente accesible.
! No utilice prolongaciones ni conexiones múltiples.
! El cable no debe estar plegado ni sufrir compresiones.
65 - 100 cm
! El cable de alimentación debe ser sustituido sólo por
técnicos autorizados.
¡Atención! La empresa fabricante declina toda responsabi-
lidad en caso de que estas normas no sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso, realice un ciclo
de lavado con detergente y sin ropa, seleccionando el
programa 2.
Datos técnicos
Modelo
IWE 81282
Dimensiones
ancho 59.5 cm
altura 85 cm
profundidad 60 cm
Capacidad
de 1 a 8 kg
Conexiones
eléctricas
ver la placa de características técnicas
aplicada en la máquina
Conexiones
hídricas
presión máxima 1 MPa (10 bar)
presión mínima 0,05 MPa (0,5 bar)
capacidad del cesto 62 litros
Velocidad de
centrifugado
máxima 1200 r.p.m.
Programas de
control según la
norma EN 60456
programa 2; temperatura 60ºC;
efectuado con 8 kg. de carga.
Esta máquina cumple con lo establecido
por las siguientes Directivas de la Comu-
nidad:
- 2004/108/CE (Compatibilidad Electro-
magnética)
- 2002/96/CE
- 2006/95/CE (Baja Tensión)
16
ES
Contenedor de detergentes: para cargar detergentes
y aditivos (ver “Detergentes y ropa”).
Botón ON/OFF
: presione brevemente el botón para
encender o apagar la máquina. El piloto START/PAUSA
que centellea lentamente de color verde indica que la
máquina está encendida. Para apagar la lavadora duran-
te el lavado, es necesario mantener presionado el botón
durante más tiempo, aproximadamente 2 seg.; si se
presiona en forma más breve o accidental, la máquina no
se apagará. Si la máquina se apaga durante un lavado en
curso, dicho lavado se anulará.
Mando de PROGRAMAS: para elegir los programas.
Durante el funcionamiento del programa el mando no se
mueve.
Botones con pilotos de FUNCIÓN: para seleccionar las
funciones disponibles. El piloto correspondiente a la fun-
ción seleccionada permanecerá encendido.
Botón CENTRIFUGADO
: presiónelo para disminuir o
excluir totalmente el centrifugado - el valor se indica en la
pantalla.
Botón TEMPERATURA
: presiónelo para disminuir o
excluir la temperatura; el valor se indica en la pantalla.
Botón COMIENZO RETRASADO
: presiónelo para
seleccionar el comienzo retrasado del programa elegido. El
retraso se indicará en la pantalla.
Botón con piloto START/PAUSA
: cuando el piloto
verde centellea lentamente, presione el botón para que
comience el lavado. Una vez que el ciclo ha comenzado,
el piloto se mantiene fijo. Para poner en pausa el lavado,
presione nuevamente el botón; el piloto centelleará con
un color anaranjado. Si el símbolo
no está iluminado,
se podrá abrir la puerta. Para que el lavado se reanude a
partir del momento en el cual fue interrumpido, presione
nuevamente el botón.
Modalidad de stand by
Esta lavadora está en conformidad con las nuevas norma-
tivas vinculadas al ahorro energético. Está dotada de un
sistema de auto-apagado (stand by) que, en caso de no
funcionamiento, se activa pasados aproximadamente 30
minutos. Presionar brevemente el botón ON-OFF y esperar
que la máquina se active.
Descripción de la lavadora
Panel de control
Botón con
piloto START/
PAUSA
Botón
TEMPERATURA
Botón
CENTRIFUGADO
Mando de
PROGRAMAS
Botones con pilotos
FUNCIÓN
Contenedor de
detergentes
Botón de ON/OFF
PANTALLA
Botón
COMIENZO
RETRASADO
ES
17
Pantalla
La pantalla es útil para programar la máquina y brinda múltiple información.
En la sección A se visualiza la duración de los distintos programas a disposición y, para los que han comenzado, el tiempo
que falta para su finalización; si se hubiera seleccionado un COMIENZO RETRASADO, se visualiza el tiempo que falta para
que comience el programa seleccionado. Además, presionando el botón correspondiente, la máquina muestra automática-
mente la temperatura y la centrífuga máximas previstas para el programa fijado o las últimas seleccionadas si son compati-
bles con el programa elegido.
En la sección B se visualizan las “fases de lavado” previstas para el ciclo seleccionado y, una vez comenzado el programa, la
“fase de lavado” en curso:
Lavado
Aclarado
Centrifugado
Descarga
En la sección C se encuentran, de arriba hacia abajo, los íconos correspondientes a la “temperatura”
, al “Comienzo retra-
sado”
y al “centrifugado” :
El símbolo
iluminado indica que en la pantalla se visualiza el valor seleccionado de “temperatura”.
El símbolo
iluminado indica que se ha seleccionado un “Comienzo retrasado”.
El símbolo
iluminado indica que en la pantalla se visualiza el valor seleccionado de “centrifugado”.
Símbolo Puerta bloqueada
El símbolo encendido indica que la puerta está bloqueada. Para evitar daños, se debe esperar que el símbolo se apague,
antes de abrir la puerta.
Para abrir la puerta mientras un ciclo está en curso, presione el botón START/PAUSA; si el símbolo PUERTA BLOQUEADA
está apagado, será posible abrir la puerta.
B
C
A
18
ES
Cómo efectuar un ciclo de lavado
1. ENCENDER LA MÁQUINA. Presione el botón ; el
piloto START/PAUSA centelleará lentamente de color
verde.
2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,
cuidando no superar la cantidad de carga indicada en la
tabla de programas de la página siguiente.
3. DOSIFICAR EL DETERGENTE. Extraiga el
contenedor y vierta el detergente en las cubetas
correspondientes como se explica en “Detergentes y
ropa”.
4. CERRAR LA PUERTA.
5. ELEGIR EL PROGRAMA. Seleccione el programa
deseado con el mando de PROGRAMAS; a dicho
programa se le asociará una temperatura y una
velocidad de centrifugado que se pueden modificar. En
la pantalla aparecerá la duración del ciclo.
6. PERSONALIZAR EL CICLO DE LAVADO. Utilice los
botones correspondientes:
Modificar la temperatura y/o el
centrifugado. La máquina muestra automáticamente
la temperatura y la centrífuga máximas previstas para
el programa fijado o las últimas seleccionadas si son
compatibles con el programa elegido. Presionando el
botón
se disminuye progresivamente la temperatura
hasta llegar al lavado en frío “OFF”. Presionando el
botón
se disminuye progresivamente el centrifugado
hasta su exclusión “OFF”. Si se presionan una vez más
los botones, se volverá a los valores máximos previstos.
Seleccionar un comienzo retrasado.
Para seleccionar el comienzo retrasado del programa
elegido, presione el botón correspondiente hasta
alcanzar el tiempo de retraso deseado. Cuando dicha
opción está activada, en la pantalla aparece el símbolo
. Para eliminar el comienzo retrasado, presione el
botón hasta que aparezca el mensaje OFF.
Modificar las
características del ciclo.
• Presione el botón para activar la función; el piloto
correspondiente al botón se encenderá.
• Presione nuevamente el botón para desactivar la
función; el piloto se apagará.
! Si la función seleccionada no es compatible con el
programa elegido, el piloto centelleará y la función no se
activará.
! Si la función elegida no es compatible con
otra seleccionada precedentemente, el piloto
correspondiente a la primera función seleccionada
centelleará y se activará sólo la segunda, el piloto de la
función activada se iluminará.
! Las funciones pueden variar la carga recomendada
y/o la duración del ciclo.
7. PONER EN MARCHA EL PROGRAMA. Presione
el botón START/PAUSA. El piloto correspondiente se
iluminará de color verde fijo y la puerta se bloqueará
(símbolo PUERTA BLOQUEADA
encendido). Para
cambiar un programa mientras un ciclo está en curso,
ponga la lavadora en pausa presionando el botón
START/PAUSA (el piloto START/PAUSA centelleará
lentamente de color anaranjado); luego seleccione el
ciclo deseado y presione nuevamente el botón START/
PAUSA.
Para abrir la puerta mientras un ciclo está en curso,
presione el botón START/PAUSA; si el símbolo PUERTA
BLOQUEADA
está apagado, será posible abrir la
puerta. Presione nuevamente el botón START/PAUSA
para reanudar el programa a partir del momento en el
que se había interrumpido.
8. FIN DEL PROGRAMA. En la pantalla aparecerá
el mensaje “END”, cuando el símbolo PUERTA
BLOQUEADA
se apague, será posible abrir la puerta.
Abra la puerta, descargue la ropa y apague la máquina.
! Si desea anular un ciclo que ya ha comenzado, presione
más tiempo el botón
. El ciclo se interrumpirá y la
máquina se apagará.
ES
19
Programas y funciones
Tabla de programas
Funciones de lavado
Seleccionando esta opción, se optimizan el movimiento
menico, la temperatura y el agua para una carga reducida
de prendas de algodón y sintéticas poco sucias (ver la “Tabla
de programas”).
Con “
” se puede lavar en un tiempo menor,
ahorrando agua y energía. Se aconseja utilizar una dosis
de detergente líquido adecuada a la cantidad de carga.
! No se puede activar con los programas 1, 2, 6, 7, 8, 9,
10, 11, 12, 13,
, , .
La función contribuye al ahorro energético
porque no calienta el agua utilizada para lavar la ropa, esto
constituye una ventaja tanto para el ambiente como para
la factura de electricidad. La mayor potencia y el consumo
optimizado del agua, garantizan óptimos resultados para
la misma duración promedio de un ciclo estándar.
Para obtener los mejores resultados de lavado, se
aconseja el uso de un detergente líquido.
! No se puede activar con los programas 1, 6, 7, 9, 11, 12,
13,
, , .
Aclarado extra
Al elegir esta función aumentará la eficacia del aclarado y
se asegurará la máxima eliminación del detergente. Es útil
para pieles particularmente sensibles.
! No se puede activar con los programas 9,
, .
Mini Carga
Se aconseja utilizar esta función cuando la cantidad de
ropa para lavar es igual o inferior a la mitad de la carga
máxima aconsejada (ver la Tabla de programas).
! No se puede activar con los programas 8, 9, 10, 11, 12,
13,
, .
Para todos los Test Institutes:
1) Programa de control según la norma EN 60456: seleccione el programa 2 con una temperatura de 60ºC.
2) Programa algodón largo: seleccione el programa 2 con una temperatura de 40ºC.
3) Programa algodón corto: seleccione el programa 4 con una temperatura de 40ºC.
Programas
Descripción del Programa
Temp.
max.
(°C)
Velocidad
máx.
(r.p.m.)
Detergentes Carga máx. (Kg.)
Duración
del ciclo
Prelavado Lavado
Suavi-
zante
Normal
Mini
Carga
Eco
Time
Diario (programas para todos los días)
1
Prelavado Algodón: blancos sumamente sucios. 90° 1200
8 4 -
2
Algodón: blancos sumamente sucios. 90° 1200 -
8 4 -
2
Algodón (1): blancos y colores resistentes muy sucios. 60° 1200 -
8 4 -
2
Algodón (2): blancos y colores delicados muy sucios. 40° 1200 -
8 4 -
3
Algodón: blancos sumamente sucios. 60° 1200 -
8 4 4
4
Algodón de color (3): blancos poco sucios y colores delicados. 40° 1200 -
8 4 4
5
Sintético: colores resistentes muy sucios. 60° 800 -
3,5 1,5 2,5
Programas Especiales
6
Lana: para lana, cachemira, etc. 40° 600 -
2 1 -
7
Seda/Cortinas: para prendas de seda, viscosa, lencería. 30° 0 -
2 1 -
8
Jeans
40° 800 -
4 - -
9
Express: para refrescar rápidamente prendas poco sucias (no se aconseja
utilizarlo para lana, seda y prendas para lavar a mano).
30° 800 -
1,5 - -
10
Outwear
30° 400 -
- 2,5 - -
Sport
11
Sport Intensive
30° 600 -
4 - -
12
Sport Light
30° 600 -
4 - -
13
Sport Shoes
30° 600 -
Max.2
pares
- -
Programas Parciales
Aclarado - 1200 - -
8 4 -
Centrifugado - 1200 - - - 8 - -
Descarga - 0 - - - 8 - -
Se puede controlar la duración de los programas de lavado en la pantalla.
La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede variar en función de numerosos factores como la
temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente, la cantidad y el tipo de carga, el equilibrado de la carga y las opciones adicionales seleccionadas.
20
ES
Detergentes y ropa
Contenedor de detergentes
El buen resultado del lavado depende también de la cor-
recta dosificación del detergente: si se excede la cantidad,
no se lava de manera más eficaz, sino que se contribuye a
encostrar las partes internas de la lavadora y a contaminar
el medio ambiente.
! No use detergentes para el lavado a mano porque pro-
ducen demasiada espuma.
Extraiga el contenedor de
detergentes e introduzca el
detergente o el aditivo de la
siguiente manera:
cubeta 1: Detergente para prelavado (en polvo)
cubeta 2: Detergente para lavado (en polvo o
líquido)
El detergente líquido se debe verter sólo antes de la pue-
sta en marcha.
cubeta 3: Aditivos (suavizante, etc.)
El suavizante no se debe volcar fuera de la rejilla.
Preparar la ropa
• Subdividalaropasegún:
- el tipo de tejido / el símbolo en la etiqueta.
- los colores: separe las prendas de color y las blancas.
• Vacíelosbolsillosycontrolelosbotones.
• Nosuperelosvaloresindicados,referidosalpesodela
ropa seca:
Tejidos resistentes: max 8 kg.
Tejidos sintéticos: max 3,5 kg.
Tejidos delicados: max 2 kg.
Lana: max 2 kg.
Seda: max 2 kg
¿Cuánto pesa la ropa?
1 sábana 400/500 g
1 funda 150/200 g
1 mantel 400/500 g
1 albornoz 900/1200 g
1 toalla 150/250 g
Programas particulares
Lana: con el programa 6 es posible lavar en la lavadora
todas las prendas de lana, aún las que contienen la eti-
queta “sólo lavado a mano”
Para obtener los mejores
resultados utilice un detergente específico y no supere
2 Kg. de ropa.
Seda: utilice el programa correspondiente 7 para lavar
todas las prendas de seda. Se aconseja el uso de un
detergente específico para prendas delicadas.
Cortinas: pliéguelas y colóquelas dentro de una funda o
de una bolsa de red. Utilice el programa 7.
Jeans: vuelva del revés las prendas antes del lavado y
utilice un detergente líquido. Utilice el programa 8.
Express (programa 9) fue estudiado para lavar prendas li-
geramente sucias y en poco tiempo: dura sólo 15 minutos
y de esa manera permite ahorrar energía y tiempo. Selec-
cionando el programa (9 a 30ºC) es posible lavar conjunta-
mente tejidos de distinto tipo (excluidas lana y seda), con
una carga máxima de 1,5 kg.
Outwear (programa 10) ha sido estudiado para lavar
tejidos repelentes al agua y anoraks (por ej.: goretex, po-
liéster, nylon); para obtener los mejores resultados, utilice
detergente líquido y en la dosis correspondiente a la media
carga; trate previamente los puños, cuellos y manchas y
no utilice suavizante o detergentes con suavizante. Con
este programa no se pueden lavar los edredones acolcha-
dos.
Sport Intensive (programa 11) ha sido estudiado para
lavar tejidos usados en prendas deportivas (chándales,
pantalones cortos, etc.) muy sucios; para obtener los
mejores resultados es aconsejable no superar la carga
máxima indicada en la “Tabla de programas”.
Sport Light (programa 12) ha sido estudiado para lavar
tejidos usados en prendas deportivas (chándales, panta-
lones cortos, etc.) poco sucios; para obtener los mejores
resultados es aconsejable no superar la carga máxima in-
dicada en la “Tabla de programas”. Se recomienda utilizar
detergente líquido y la dosis correspondiente a la media
carga.
Sport Shoes (programa 13) ha sido estudiado para lavar
calzado deportivo; para obtener los mejores resultados no
lave más de 2 pares a la vez.
Sistema de equilibrado de la carga
Antes de cada centrifugado, para evitar vibraciones exce-
sivas y para distribuir la carga de modo uniforme, el cesto
realiza rotaciones a una velocidad ligeramente superior a la
del lavado. Si después de varios intentos, la carga todavía
no está correctamente equilibrada, la máquina realiza el
centrifugado a una velocidad inferior a la prevista. Cuando
existe un excesivo desequilibrio, la lavadora realiza la
distribución antes que el centrifugado. Para obtener una
mejor distribución de la carga y su correcto equilibrado, se
aconseja mezclar prendas grandes y pequeñas.
1
2
3
1 / 1

Whirlpool IWE 81282 B ECO (EU) Kullanici rehberi

Kategori
Çamaşır makineleri
Tip
Kullanici rehberi