Yamaha MGP24X Kullanım kılavuzu
- Kategori
- Tamamlayıcı müzik ekipmanı
- Tip
- Kullanım kılavuzu
Bu kılavuz için de uygundur
MGP32X/MGP24X Owner’s Manual
2
The above warning is located on the rear of the unit.
L’avertissement ci-dessus est situé sur le arrière de l’appareil.
Explanation of Graphical Symbols
Explication des symboles
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « ten-
sion dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions
importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.
IMPORTANT SAFETY
INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat regis-
ters, stoves, or other apparatus (including amplifiers) that produce
heat.
9 Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particu-
larly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com-
bination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms
or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
(UL60065_03)
PRÉCAUTIONS CONCER-
NANT LA SÉCURITÉ
1 Lire ces instructions.
2 Conserver ces instructions.
3 Tenir compte de tous les avertissements.
4 Suivre toutes les instructions.
5 Ne pas utiliser ce produit à proximité d’eau.
6 Nettoyer uniquement avec un chiffon propre et sec.
7 Ne pas bloquer les orifices de ventilation. Installer l’appareil confor-
mément aux instructions du fabricant.
8 Ne pas installer l’appareil à proximité d’une source de chaleur
comme un radiateur, une bouche de chaleur, un poêle ou tout autre
appareil (y compris un amplificateur) produisant de la chaleur.
9 Ne pas modifier le système de sécurité de la fiche polarisée ou de la
fiche de terre. Une fiche polarisée dispose de deux broches dont
une est plus large que l’autre. Une fiche de terre dispose de deux
broches et d’une troisième pour le raccordement à la terre. Cette
broche plus large ou cette troisième broche est destinée à assurer
la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas
compatible avec les prises de courant disponibles, faire remplacer
les prises par un électricien.
10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas
piétinés ni coincés, en faisant tout spécialement attention aux
fiches, prises de courant et au point de sortie de l’appareil.
11 Utiliser exclusivement les fixations et accessoires spécifiés par le
fabricant.
12 Utiliser exclusivement le chariot, le stand, le
trépied, le support ou la table recommandés
par le fabricant ou vendus avec cet appareil.
Si l’appareil est posé sur un chariot, déplacer
le chariot avec précaution pour éviter tout ris-
que de chute et de blessure.
13 Débrancher l’appareil en cas d’orage ou
lorsqu’il doit rester hors service pendant une période prolongée.
14 Confier toute réparation à un personnel qualifié. Faire réparer
l’appareil s’il a subi tout dommage, par exemple si la fiche ou le cor-
don d’alimentation est endommagé, si du liquide a coulé ou des
objets sont tombés à l’intérieur de l’appareil, si l’appareil a été
exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas
normalement ou est tombé.
(UL60065_03)
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE
ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À
L’HUMIDITÉ.
MGP32X/MGP24X Owner’s Manual
3
Contents
PRECAUTIONS ...................................... 4
Introduction......................................... 6
Main features .......................................................6
Setup................................................. 7
Preparing the power supply ...............................7
Connections ........................................................7
Powering up the system .....................................7
Getting sound to the speakers...........................7
Setup example.....................................................8
Controls and Connectors ....................... 10
Top panel ...........................................................10
Rear panel..........................................................10
Channel control block ......................................11
Mono input section ....................................................11
Stereo input section...................................................11
Master control block .........................................15
USB device recorder section..................................... 15
iPod/iPhone section................................................... 15
Display section ..........................................................16
Meter section............................................................. 16
FX RTN (effect return) section .................................17
SEND MASTER section............................................ 18
MATRIX section ........................................................18
USB IN/iPod IN section ............................................. 19
PHONES/MONITOR section.....................................19
TALKBACK section ...................................................20
GROUP section.........................................................20
MONO master section...............................................21
STEREO master section ...........................................21
Rear input/output block....................................22
Channel I/O connectors section ................................22
Master I/O connectors section...................................22
Power section............................................................23
Basic Operations and Display.................. 24
Viewing the display...........................................24
Operations of the screen..................................25
Using Effects (FX)................................ 26
Applying effects ................................................26
Detailed effect settings .....................................26
Applying two effects simultaneously ..............27
Displaying FX1 and FX2 together ....................27
Using Graphic EQ ................................. 28
About the graphic EQ (GEQ)........................... 28
Setting the GEQ................................................ 28
Finding and removing feedback ..................... 29
Calling up/saving the GEQ program............... 30
Using the Compressor ........................... 31
About the master compressor ........................ 31
Specifying the compressor settings .............. 31
Calling up/saving the compressor program .. 32
Recording/Playing back ......................... 33
About USB device recording/playing back .... 33
Recording to a USB device.............................. 33
Playing back songs from a USB device ......... 34
Playing back songs from an iPod/iPhone ...... 36
Specifying the recording/playback settings .. 36
Using Other Functions ........................... 37
Applying the Low Pass Filter (LPF) ................ 37
Using the Ducker function............................... 37
Using the Leveler function .............................. 38
Initializing the unit to the factory default
settings (resetting user memory)......... 39
Troubleshooting .................................. 40
Appendix........................................... 42
Message List..................................................... 42
Effect Program List .......................................... 43
Parameter List .................................................. 44
Jack List............................................................ 46
Dimensions....................................................... 47
Specifications................................................... 48
Index.................................................................. 51
Block Diagram and Level Diagram ................. 52
MGP32X/MGP24X Owner’s Manual
4
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to,
the following:
• Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
• Only use the voltage specified as correct for the device. The required voltage
is printed on the name plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you purchased,
the included power cord may not be compatible. Please check with your
Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
• This device contains no user-serviceable parts. Do not open the device or
attempt to disassemble the internal parts or modify them in any way. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as
water seeps into the device, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the device inspected by qualified
Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
• Do not put burning items, such as candles, on the unit. A burning item may
fall over and cause a fire.
• When one of the following problems occur, immediately turn off the power
switch and disconnect the electric plug from the outlet. Then have the device
inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or
damage to the device or other property. These precautions include, but are not limited to, the following:
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• Do not place the device in an unstable position where it might accidentally
fall over.
• Do not block the vents. This device has ventilation holes at the bottom and
sides to prevent the internal temperature from becoming too high. In
particular, do not place the device on its side or upside down. Inadequate
ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the
power switch is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a long time, make
sure to unplug the power cord from the wall AC outlet.
• Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all volume
levels to minimum.
• Remove the power plug from the AC outlet when cleaning the device.
Power supply/Power cord
Do not open
Water warning
Fire warning
If you notice any abnormality
Power supply/Power cord
Location
Connections
Maintenance
PA_en_1 1/2
MGP32X/MGP24X Owner’s Manual
5
• Do not insert your fingers or hands in any gaps or openings on the device
(vents, ports, etc.).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into
any gaps or openings on the device (vents, ports, etc.) If this happens, turn
off the power immediately and unplug the power cord from the AC outlet.
Then have the device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid
use excessive force on the buttons, switches or connectors.
• Do not use speakers or headphones for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing loss. If
you experience any hearing loss or ringing in the ears, consult a physician.
Always turn the power off when the device is not in use.
NOTICE
To avoid the possibility of malfunction/damage to the prod-
uct, damage to data, or damage to other property, follow the
notices below.
Handling and Maintenance
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Oth-
erwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibrations,
or extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day) to prevent the possibility
of panel disfiguration, damage to the internal components
or unstable operation.
• Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel of this device.
• When cleaning the device, use a dry and soft cloth. Do
not use paint thinners, solvents, cleaning fluids, or chemi-
cal-impregnated wiping cloths.
• Condensation can occur in the device due to rapid, dras-
tic changes in ambient temperature—when the device is
moved from one location to another, or air conditioning is
turned on or off, for example. Using the device while con-
densation is present can cause damage. If there is reason
to believe that condensation might have occurred, leave
the device for several hours without turning on the power
until the condensation has completely dried out.
• Avoid setting all equalizer controls and faders to their
maximum. Depending on the condition of the connected
devices, doing so may cause feedback and may damage
the speakers.
• Do not apply oil, grease, or contact cleaner to the faders.
Doing so may cause problems with electrical contact or
fader motion.
• When turning on the AC power in your audio system,
always turn on the power amplifier LAST, to avoid speaker
damage. When turning the power off, the power amplifier
should be turned off FIRST for the same reason.
Saving data
• To protect against data loss due to media damage, we
recommend that important data that has been saved via
the USB device recorder to a USB device should also be
saved to your computer or an external USB device.
Connectors
XLR-type connectors are wired as follows (IEC60268 stan-
dard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Insert TRS phone jacks are wired as follows: sleeve:
ground, tip: send, and ring: return.
Information
About copyrights
• Copying of the commercially available musical data including but
not limited to MIDI data and/or audio data is strictly prohibited
except for your personal use.
About this manual
• The illustrations and LCD screens as shown in this manual are
for instructional purposes only, and may appear somewhat differ-
ent from those on your device.
• Throughout this manual, all panel illustrations show the panel of
the MGP32X.
• The company names and product names in this manual are the
trademarks or registered trademarks of their respective compa-
nies.
iPod
TM
, iPhone
TM
iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
“Made for iPod” and “Made for iPhone” mean that an elec-
tronic accessory has been designed to connect specifically
to iPod or iPhone respectively, and has been certified by the
developer to meet Apple performance standards. Apple is
not responsible for the operation of this device or its compli-
ance with safety and regulatory standards. Please note that
the use of this accessory with iPod or iPhone may affect
wireless performance.
Handling caution
Yamaha cannot be held responsible for damage caused by improper use
or modifications to the device, or data that is lost or destroyed.
PA_en_1 2/2
MGP32X/MGP24X Owner’s Manual
6
Introduction
Main features
D-PRE (Discrete Class-A MIC preamp)
Mono input channels are equipped with Class-A discrete micro-
phone preamplifiers. The head amplifier features an inverted Dar-
lington circuit* used in high-end audio devices, and reproduces
low frequencies with exceptionally musical characteristics as
well as sustained high frequencies. Independent toggle switching
of +48V phantom power and 26dB (pad) on each channel.
* Inverted Darlington circuit: An amplifying method for elimi-
nating the nonlinear characteristics of the amplifier element
and suppressing the distortion. The circuit features highly
musical phase characteristics.
X-pressive EQ
The shelving EQ (low/high) on the mono input channels features
Xpressive EQ, which effectively models analog EQ utilizing
Yamaha’s famed VCM (Virtual Circuitry Modeling) technology.
We analyzed vintage EQ analog circuits and redesigned the tech-
nology specifically for the MGP to create an EQ with exception-
ally musical characteristics. Furthermore, the cutoff frequency
can also be adjusted, enhancing use of the EQ in sound reinforce-
ment applications, and extending the sonic control range of the
mixer.
USB device recorder
A USB device recorder is built into the mixer for recording mixed
audio to a USB device as an audio file, and for playing back
music saved in the USB device by assigning it to the desired
channel output or bus output. Supported file formats are MP3
(MPEG-1 Audio Layer-3) and WAV for recording and MP3,
WAV, and AAC for playback.
Stereo master – COMP and GEQ
The stereo master is equipped with a compressor (COMP) or
multiband compressor that adjusts the sound pressure of the out-
put signal, and with a graphic equalizer (GEQ) that adjusts sound
quality such as feedback.
Digital effects — REV-X and SPX
Two powerful digital effect blocks are built into the mixer: REV-
X (8 types) and SPX (16 types). REV-X gives you a high-density,
richly reverberant sound ambience, with smooth attenuation,
spread and depth that work together to enhance the original
sound. The versatile SPX block features a variety of effect appli-
cations, such as reverb, delay, and modulation effects, along with
complex combinations of multiple effects.
Convenient, practical functions for events –
Ducker, Leveler, and Stereo Image
The mixer features three exceptionally convenient features for the
stereo input channels: Ducker, Leveler and Stereo Image. The
ducker function automatically lowers the level of background
music to accommodate the voice of an announcer coming in on
another channel. The leveler function automatically maintains a
consistent sound volume, even when using sound sources that
have different mastering levels. Stereo image narrows the pan
balance of the stereo sound source, and changes stereo signals to
mono. This is useful in restaurants and other spaces where the left
and right speakers are distantly positioned, or when you input
accompaniment sound to the left channel and vocal sound to the
right and want a more natural stereo image.
USB port for playing and charging your iPod/
iPhone
Digital audio output from the iPod/iPhone can be directly input to
the unit, and the iPod/iPhone can be charged while connected.
About the models
The MGP32X and MGP24X feature a different number of mon-
aural input channels and COMP control knobs. The MGP32X has
24 monaural input channels and the MGP24X has 16. The
MGP32X is equipped with 16 COMP control knobs for channels
9-24 and the MGP24X with 8 COMP control knobs for channels
9-16.
Conventions in this manual
• Whenever there is a different number of channels or a different
channel number for the same function between the MGP32X
and the MGP24X, the number that applies only to the MGP24X
model is enclosed in curly brackets { }. For example, “CH1-24
{CH1-16}” means channels 1-24 for the MGP32X and chan-
nels 1-16 for the MGP24X.
* “CH” is an abbreviation for channel.
• Control knobs on the panel are called “knobs.” Some knobs
rotate from a minimum value to a maximum value, while others
rotate endlessly.
MGP Editor
MGP Editor is a free software application that gives you addi-
tional control of your MGP mixer’s DSP settings via your iPhone,
iPod touch, and iPad. See the following web site to download the
application.
http://www.yamahaproaudio.com/global/en/products/periph-
erals/applications/mgp_editor/
Included Accessories
• AC Power Cord
• Owner’s manual (this book)
Thank you for purchasing the Yamaha MGP32X/MGP24X
mixing console.
Please read this manual thoroughly to make the best use of
the mixing console for the longest possible period of time.
After reading this manual, please keep it available for future
reference.
MGP32X/MGP24X Owner’s Manual
7
Setup
Preparing the power supply
1. Make sure that the power switch of the unit is
set to the “ ” position (off).
2. Connect the socket of the included power cord
to the [AC IN] connector.
3. Plug the power cord into a power outlet.
CAUTION
• Unplug the power cord from the outlet when not using the
mixer or during electrical storms.
Connections
1. Turn all the faders and GAIN knobs completely
down.
2. Connect speakers, microphones and/or instru-
ments.
Refer to “Setup example” on pages 8-9 for more information
on connections.
Powering up the system
To prevent an unwanted burst of noise from the
speakers, power up the devices in the following
order: peripheral devices (instrument, micro-
phone, iPod) MGP mixer power amps (or
powered speakers).
Reverse this order when turning the power off.
CAUTION
• Be sure to turn the power on/off in this order every time you
use the mixer. Failure to do so may result in loud noise
bursts that can damage your equipment, your ears, or both.
Getting sound to the speakers
1. While producing sound on your instrument or
microphone, adjust the channel GAIN knobs
so that the corresponding peak indicators
flash briefly at the highest peak levels.
NOTE
• To use the level meter to get a more accurate reading of the
incoming signal level, turn on the channel PFL switch. Adjust
the GAIN knobs so that the PFL/AFL level meter indicator
only occasionally rises above the “0” level.
• The gain (volume) level of the audio files in the USB device
may be too high. Refer to the NOTE on page 35 to adjust the
volume.
• Note that the PHONES jack or MONITOR OUT jacks output
the pre-fader signal from all channels for which the PFL
switch is ON, so that those signals can be monitored.
2. Turn on ( ) the ON and ST (Stereo) switches
for each channel you are using.
3. Make sure that all the PFL and AFL switches
are off ( ).
4. Turn on ( ) the ON switch of the STEREO
master.
5. Raise the STEREO master fader to the 0 dB
position.
6. Adjust the volume of each channel by moving
its fader up and down.
7. Adjust the overall volume with the STEREO
master fader.
The overall headphone level is adjusted with the PHONES
knob.
NOTE
If the PEAK indicator lights frequently, slowly lower the channel
faders a little to avoid distortion.
GAIN knobs Power switch (rear panel)
Faders
1 GAIN knob
6 Fader
2 ON switch
1 PEAK
indicator
2 ST switch
Channel
STEREO master
3 PFL switches
AFL switches
5 STEREO
master fader
4 ON switch
1, 7
Level meter
3
AFL switches
Setup
MGP32X/MGP24X Owner’s Manual
8
Microphones for
talkback
DVD player (voice)
Computer/Audio interface
DJ mixer
Synthesizer
Power amp
Powered speakers
Microphone
CH24 {CH16} (for MC)
Setup example
Lamp
(Yamaha LA-1L)
CD player
Powered monitor
speakers
Foyer etc.
Stage
Speakers
Powered monitor speakers
(For musician monitoring)
Powered
subwoofer
MGP32X/MGP24X Owner’s Manual
9
Setup
USB device
iPod/iPhone
Headphones
Compressor
Instrument, Microphone
Microphone
x 8
Drum
Bass
Rear panel
*The illustrations show the
panel of the MGP32X.
Top panel
CAUTION
• When using a condenser
microphone, set the +48V
phantom switch to ON
(page 11).
* If electric guitars and basses can be con-
nected directly to the mixer’s inputs, use a
DI box (direct box) or amp simulator
between the instrument and the mixer.
MGP32X/MGP24X Owner’s Manual
10
Controls and Connectors
Top panel
Mono input section
(page 11)
Stereo input section
(page 11)
USB device recorder section (page 15)
Display section (page 16)
iPod/iPhone section (page 15)
Meter section (page 16)
SEND MASTER
section (page 18)
MATRIX section
(page 18)
USB IN/iPod IN section
(page 19)
PHONES/MONITOR
section (page 19)
TALKBACK section
(page 20)
STEREO master section (page 21)
MONO master section (page 21)
GROUP section (page 20)
FX RTN (effect return) section (page 17)
Channel I/O connectors section (page 22)
Master I/O connectors section (page 22)
Power section (page 23)
Rear panel
Channel Control Block (input) Master Control Block (output)
MGP32X/MGP24X Owner’s Manual
11
Controls and Connectors
Channel control block
Mono input section
Stereo input section
q 26dB (PAD) switch
Turning this switch on ( ) attenuates the input signal from
the INPUT jack of the mono channel by 26dB. Turn this
switch off ( ) if you have connected a microphone or other
device with a low input level to the channel. Turn it on ( )
if you have connected a line-level device.
w +48V switch and indicator
Toggles phantom power on and off. When this switch is
turned on ( ), the mixer supplies DC +48V power to
INPUT A of XLR input jacks. Turn this switch on when
using one or more phantom-powered condenser microphones.
The indicator is on when the switch is on.
CAUTION
• Be sure to leave this switch off ( ) if you do not need
phantom power.
• When turning phantom power on ( ), follow the impor-
tant precautions below, in order to prevent noise and
possible damage to the mixer and external devices.
• Turn this switch off when connecting a device that
does not support phantom power to INPUT A of XLR
input jacks
• Do not connect/disconnect a cable to/from channels 1-
24 {1-16} while this switch on.
• Turn the mixer’s output controls – STEREO master and
GROUP faders- all the way down when turning phan-
tom power on/off.
e GAIN knob
Adjusts the sensitivity of the input signal. Monaural channels
have a 26dB switch (q) that lets you change the range of this
control. The adjustable sensitivity range is as follows.
Mono channel
NOTE
The stereo channel is fixed to a range of -34dB to +10dB.
r (High Pass Filter) switch
Turning this switch on ( ) will apply a high-pass filter that
attenuates frequencies below 100Hz in the signal by a slope
of 12dB/octave.
t
COMP knobs and indicator (Channel 9-24 {9-16})
Adjusts the amount of compression applied to the channel.
As the knob is turned to the right the compression ratio
increases while the output gain is automatically adjusted
accordingly. The result is smoother, more even dynamics
because louder signals are attenuated while the overall level
is boosted. The COMP indicator comes on when the com-
pressor operates.
NOTE
Avoid setting the compression too high, as the higher average
output level that results may lead to feedback.
Continue to next page
Mono channels
1–24 (MGP32X)
1–16 (MGP24X)
Stereo channels
25–32 (MGP32X)
17–24 (MGP24X)
* y-!0 are for CH29/
30, CH31/32 {CH21/
22,CH23/24} only.
Channel number
Channel number
26dB switch Range
ON -34dB to +10dB
OFF -60dB to -16dB
Controls and Connectors
MGP32X/MGP24X Owner’s Manual
12
y DUCKER SOURCE indicator
The indicator of the selected input source (CH24 {CH16} or
GROUP1) comes on. The input source can be selected on the
display (page 37).
u DUCKER switch
Turning this switch on ( ) lowers the volume of the stereo
channel automatically when a signal exceeding a certain level
is input to the input source (CH24 {CH16} or GROUP1).
When the switch is turned on, the switch’s lamp comes on.
i LEVELER switch and indicator
Turning this switch on ( ) allows the volume to be
adjusted automatically to a certain level, when the actual
sound output level differs for each song. The indicator is on
when the switch is on.
o Input select switch
Selects the input signal source. If this switch is set to ANA-
LOG( ), the jacks for CH29/30 and 31/32 {CH21/22, 23/
24} will be the input source. If this switch is set to USB IN
( ) or iPod IN ( ), the signal from an USB device or
iPod/iPhone will be the input source. The signal from an USB
device will be input to CH29/30 {21/22}, while the signal
from an iPod/iPhone will be input to CH31/32 {23/24}.
NOTE
The GAIN knobs do not affect the volume of your iPod/iPhone.
To adjust the pre-channel-fader signal volume, refer to page
36.
!0 STEREO IMAGE switch
Selects the type of output signal for the input stereo signal.
• MONO : Mono signal
• BLEND : Stereo signal in which left and right inputs
are mixed at a certain percentage for a more nat-
ural stereo image, and in which the pan is con-
trolled.
• STEREO : Stereo signal (original, as is)
!1 Equalizer knobs (HIGH, MID, and LOW)
This three-band equalizer changes the tone of the high, mid,
and low frequency bands. Turning the knob to the right boosts
the corresponding frequency band, while turning to the left
attenuates the band. Setting the knob to the “t” position pro-
duces a flat response in the corresponding band. The upper
knob sets the center frequency for the mid range, while the
lower knob sets the amount of attenuation or boost (counter-
clockwise/clockwise) for the range. For the CH25/26 and
CH27/28 {CH17/18 and CH19/20}, the attenuation/boost can
only be set at a fixed 2.5kHz center frequency. The following
table shows the EQ type, frequency, and cut/boost range for
each of the three bands.
* The MID frequency can be adjusted from 250Hz to 5kHz.
The MID frequency is 2.5kHz when the MID frequency
control is set at the center position.
Mono channels
1–24 (MGP32X)
1–16 (MGP24X)
Stereo channels
25–32 (MGP32X)
17–24 (MGP24X)
* y-!0 are for CH29/
30, CH31/32 {CH21/
22,CH23/24} only.
Channel number
Channel number
Band Type Frequency
Cut/Boost
range
HIGH Shelving 8kHz
±15dBMID Peaking 2.5kHz*
LOW Shelving 125Hz
MGP32X/MGP24X Owner’s Manual
13
Controls and Connectors
!2 AUX knobs (1-4)
These knobs adjust the channel’s signal levels into AUX
buses 1 to 4. Each knob controls the signal into the corre-
sponding AUX bus. On stereo channels, the LINE L (odd)
and LINE R (even) input signals are mixed before moving
into the AUX bus. These knobs should generally be set close
to the “t” (nominal) position.
NOTE
• To enable use of AUX5 and AUX6, you must turn on ( )
the AUX5/AUX6 switch (!5).
• For AUX1 to AUX4, you use the PRE switch (!3) to select
whether the pre-fader or post-fader signal is sent to the bus.
For AUX5 and AUX6, only the post-fader signal can be sent.
!3 PRE switch
Selects whether the pre-fader or the post-fader signal is fed to
the corresponding pair of AUX 1-4 buses. AUX1 and 2 and
also AUX3 and 4 should be paired. The upper PRE switch
controls the signal to AUX1 and AUX2; the lower switch
controls the signal to AUX3 and AUX4. If the switch is on
( ), the mixer feeds the pre-fader signal to the correspond-
ing buses. If off ( ), the mixer feeds the post-fader signal.
!4 FX (effect) knobs (1, 2)
These knobs adjust the channel’s post-fader signal levels into
FX buses 1 and 2. On stereo channels, the LINE L (odd) and
LINE R (even) input signals are mixed before moving into
the FX bus. These knobs should generally be set close to the
“t” (nominal) position.
NOTE
If the AUX5/AUX6 switch is on, these knobs adjust the output
to the AUX5 and AUX6 buses.
!5 AUX5, AUX6 switch
Selects whether the channel’s post-fader signal is sent to
AUX buses 5 and 6 or FX buses l and 2. If the switch is on
( ), the signal goes to AUX5 and 6 buses; if off ( ), the
signal goes to the FX buses.
!6 PAN knob (Mono channels)
BAL knob (Stereo channels)
These knobs set the stereo pan position and determine the
volume balance between left and right. When the channels
are panned hard left or hard right, sound is heard from only
the hard-panned channel.
The PAN knob determines each mono signal’s pan position-
ing between left and right, while the BAL knob determines
the stereo channel’s volume balance between left and right.
!7 ON switches
Turning this switch on ( ) sends that channel’s signal to
the buses. When the switch is turned on, the switch’s lamp
comes on. If you turn the switch off ( ), all of the signal
sent to the buses such as AUX and GROUP buses is cut off.
NOTE
• The ON switch does not affect the operation of the PFL
switch (@1). You can monitor the channel’s pre-fader signal
through the PHONES jack even when the ON switch is off.
• To reduce noise, turn all unused channels off.
!8 PEAK indicator
Lights red when the channel’s post-equalizer signal level
reaches 3 dB before clipping.
!9 SIG (Signal) indicator
Lights green when a signal is being input to the channel.
@0 Bus assign switches
These switches determine the bus(es) to which each channel’s
signal is sent. Press the switch in ( ) to output the signal to
the corresponding bus.
• Switches 1-2, 3-4: Assign the channel’s signal to the
GROUP 1 to 4 buses.
• ST switch: Assigns the channel’s signal to the STE-
REO L and R buses.
NOTE
To send the signal to each bus, engage the ON switch (!7).
@1 PFL (Pre-Fader Listen) switch and indicator
When the PFL switch is turned on ( ) the indicator comes
on and the channel pre-fader signal is output to the MONI-
TOR OUT and PHONES jacks for monitoring.
@2 Channel fader
Adjusts the output level of the input channel signal. Use these
faders to adjust the balance between the various channels.
NOTE
To reduce noise, set the fader sliders for any unused channels
all the way down.
Controls and Connectors
MGP32X/MGP24X Owner’s Manual
14
AUX1
AUX2
ST
1–2
3–4
AUX3
AUX4
Mono Channel
Stereo Channel
MGP32X/MGP24X Owner’s Manual
15
Controls and Connectors
Master control block
USB device recorder section
With this section you can connect a USB device to record and
play back music. (page 33)
q USB IN connector
Connects the USB device.
w USB ACCESS indicator
Lights while the unit accesses the USB device.
Transport section
e REW button
Press to move to the previous song. Holding down this button
while playing back rewinds the song.
r PLAY button and indicator
Press to alternately start/pause playback of the song. The
indicator lights during playback, and flashes while paused.
t FWD button
Press to move to the next song. Holding down this button
while playing back forwards the song. Pressing this button
while recording stops the current recording and begins
recording a new file.
y REC button and indicator
Press to start/stop recording. The indicator lights while
recording.
iPod/iPhone section
This section lets you connect an iPod/iPhone to play back a song
(page 36) and charge the iPod/iPhone. The unit charges the iPod/
iPhone while it is connected to and recognized by the unit.
q iPod/iPhone IN connector
Use an USB cable to connect an iPod/iPhone.
w iPod indicator
Lights when the unit is accessing an iPod/iPhone.
CAUTION
• Use the genuine Apple Dock Connector USB Cable for
the iPod/iPhone connection.
• When connecting to an iPod/iPhone, allow at least 6 sec-
onds to pass between turning the mixer on and off and
plugging or unplugging the USB cable.
• Please do not use a USB hub.
• The unit’s iPod/iPhone IN connector is dedicated to
iPod/iPhone use only. Please do not connect other USB
devices.
NOTE
If you connect an iPhone, incoming calls or emails may cause
a notification sound to be output. In order to prevent this, we
recommend setting the iPhone’s Airplane mode to “on.”
Capacity and format of the USB device
Up to 64GB of the capacity for the USB device is guaranteed
by Yamaha. (However, Yamaha cannot guarantee operation
for all the USB devices). The supported file system is FAT32.
The maximum size of one file is 2GB.
NOTICE
• While the unit is accessing data (such as during
recording, playing back, and saving operations), do
NOT remove the USB device from the USB IN con-
nector, and do NOT turn off the unit. Doing so may
damage the USB device or corrupt the data on either
or both the unit and the USB device.
• Make sure that you insert the USB device all the way
in the correct orientation or upside down. Avoid
inserting with excessive force.
ert y
Transport
section
Controls and Connectors
MGP32X/MGP24X Owner’s Manual
16
Display section
This section is for setting and operating the display. Refer to
pages 24-25 for details.
q Display
Indicates the various messages and settings related to the cur-
rently selected operation or function.
w Knob 1, Knob 2
Selects/sets the functions and parameters appearing on the
display. Rotate Knob 1 to operate the functions on the lower
left side of the display, and Knob 2 for the functions on the
lower right side of the display.
e HOME button
Calls up the display to view the status of the functions. This
button does not determine or change the parameter.
r FX1 and FX2 buttons
Call up the display to switch the programs of FX1 (effect1)
and FX2 (effect2) and to adjust their parameters.
t GEQ button
Calls up the display to set the Graphic equalizer (GEQ).
y COMP button
Calls up the display to set the compressor.
u USB button
Calls up the display to record and play back with the USB
device.
i SETUP button
Calls up the display to adjust the contrast of the display, and
to set the ducker and the leveler.
Meter section
Use these meters to view various signal levels: the levels to the
STEREO OUT L/R jacks, the PFL and AFL levels, and the levels
to the GROUP OUT 1-4 jacks. The PFL or AFL signals indicated
by these meters can be monitored through the MONITOR OUT
jacks and the PHONES jack.
q METER SELECT button and indicator
Switches the display of the level meter to the output signal
level of the STEREO OUT L/R and the PHONES jacks, or of
the GROUP OUT 1-4 jacks. The indicators for the selected
signals come on.
w STEREO level meter
Shows the signal level output to the STEREO OUT L/R jacks
or the GROUP OUT 1 and 2 jacks, respectively. The “0”
position corresponds to the standard level. The PEAK indica-
tor lights red when the level hits the clipping point.
e PFL/AFL level meter
Shows the signal level output to the PHONES jack or the
GROUP OUT 3 and 4 jacks, respectively. The “0” position
corresponds to the standard level. The PEAK indicator lights
red when the level hits the clipping point.
NOTE
The PFL signal has display priority over the AFL signal when
an input channel’s PFL switch is on.
Knob 1 Knob 2
MGP32X/MGP24X Owner’s Manual
17
Controls and Connectors
FX RTN (effect return) section
This section sets the effect returns (FX1 and FX2) on/off, and
determines the level of the effect signal and to which bus the sig-
nal is sent.
q AUX (PRE) knobs (1-4)
These knobs adjust the level of the effect sent to the AUX1 to
AUX4 buses.
w FX TO FX BLEND knob
Sends the signal from FX1 to FX2 and from FX2 to FX1.
Rotate this knob from the center “OFF” position to the right to
adjust the send level from FX1 to FX2, and to the left to adjust
the send level from FX2 to FX1. Only the pre-fader signal can
be sent.
e TAP button and indicator
This feature lets you set the delay time for FX2 by tapping on
the button. This feature only works when the effect type for
FX2 is set to “, DELAY” or “. SINGLE DELAY.” To set
the delay time, tap on the button at the appropriate interval.
The average interval at which you tap the button will be cal-
culated, and that value will be set for the delay time. Continue
tapping as necessary until you get the timing right.
The TAP indicator flashes in sync with the delay time when
, DELAY or . SINGLE DELAY is selected.
NOTE
• Adjust the average interval within range of the variable delay
time.
• See page 44 for the range of the variable delay time.
r ON switch
Turn this switch on
()
to enable the FX RTN (effect
return). When the switch is turned on, the switch’s lamp comes
on.
t SIG (Signal) indicator
Lights when an effect signal is input into the channel.
y Bus assign switches
These switches determine the bus(es) to which the signal of the
internal digital effects is sent. Press the switch in
()
to out-
put the signal to the corresponding buses.
• Switches 1-2, 3-4: Assign to the GROUP1 to
GROUP4 buses.
• ST switch: Assigns to the STEREO L/R bus.
u PFL (Pre-Fader Listen) switch and indicator
When the PFL switch is turned on
()
, the indicator will
light and the pre-FX (1, 2) RTN-fader signal is output to the
MONITOR OUT and PHONES jacks for monitoring.
i FX RTN (effect return) faders (1, 2)
These adjust the level of the effect sent from the internal effect
to the GROUP1 to GROUP4 buses, and STEREO L/R buses.
First tap Second tap Third tap Fourth tap
ab c
The average interval will be set (the average of a, b, and c)
Controls and Connectors
MGP32X/MGP24X Owner’s Manual
18
SEND MASTER section
This section adjusts the levels and controls the output of signals
from the six AUX buses. Each of these signals outputs to the cor-
responding SEND (AUX1-AUX6) jack respectively.
q AUX knobs (1-6)
These knobs adjust the level of the signal from the indicated
AUX1 to AUX6 buses into the corresponding SEND (AUX1 to
AUX6) jacks. The
“t”
position of the knob is the nominal
level (0 dB).
w AFL (After-Fader Listen) switch and indicator
Turning this switch on monitors the post-AUX1 to AUX6 knob
(q)
signals that output to the MONITOR OUT and PHONES
jacks for monitoring.
NOTE
• The PFL signal has priority when both the PFL switch and
AFL switch are on. To monitor the post-fader signal, make
sure to turn off all PFL switches.
• If the PFL (preferred) is enabled, the AFL indicator does not
light, even if the AFL switch is pressed.
MATRIX section
This section adjusts the levels and controls the output of signals
to the MATRIX OUT jacks from GROUP OUT and STEREO
OUT. The signals from the MATRIX 1 and 2 buses are sent to the
MATRIX 1 and 2 jacks respectively.
q GROUP knobs (1-4)
These knobs adjust the level of the signals sent from GROUP
OUT 1-4 buses to the MATRIX OUT jacks.
w STEREO knobs (L, R)
These knobs adjust the level of the signals sent from STEREO
OUT L/R buses to the MATRIX OUT jacks.
e MATRIX master knobs (1, 2)
These knobs adjust the overall level of the signal output to the
MATRIX OUT jacks.
NOTE
The “t” positions of the knobs for (q), (w),and (e) indicate
the nominal level (0 dB).
r AFL switch and indicator
When the AFL switch is on, the indicator will light and the sig-
nal after the MATRIX master knob is output to the PHONES
and MONITOR OUT jacks for monitoring.
MGP32X/MGP24X Owner’s Manual
19
Controls and Connectors
USB IN/iPod IN section
This section determines the destination of the signal output from
the connected USB device or iPod/iPhone, and adjusts the signal
level.
q USB IN knob
Adjusts the playback level from the connected USB device.
w TO STEREO/TO MONITOR switch
Determines the destination of the signal output from the con-
nected USB device.
• TO STEREO ( ): Sends to the STEREO L/R bus.
• TO MONITOR ( ): Sends to the MONITOR OUT
jacks and PHONES jack.
e iPod IN knob
Adjusts the playback level from the connected iPod/iPhone.
r TO STEREO/TO MONITOR switch
Determines the destination of the signal output from the con-
nected iPod/iPhone.
• TO STEREO ( ): Sends to the STEREO L/R bus.
• TO MONITOR ( ): Sends to the MONITOR OUT
jacks and PHONES jack.
NOTE
CH29/30, 31/32 {CH21/22,23/24} can be selected as the desti-
nations of the signal input from the connected USB device or
iPod/iPhone (pages 34, 36).
PHONES/MONITOR section
You connect a pair of headphones and adjust the output signal
level to the PHONES and MONITOR OUT jacks.
q PHONES jack
Connect a pair of headphones to this TRS phone jack. The
PHONES jack outputs the same signal as the MONITOR OUT
jacks.
w PHONES knob
Adjusts the level of the signal output to the PHONES jack.
e MONITOR knob
Adjusts the level of the signal output to the MONITOR OUT
jacks.
NOTE
If you want to monitor the output signal from the STEREO,
MONO or GROUP bus, turn on the AFL switch of each respec-
tive bus.
Controls and Connectors
MGP32X/MGP24X Owner’s Manual
20
TALKBACK section
Use the talkback function to send instructions mainly from the
operator to musicians and studio staff. This section adjusts the
level of the microphone signal received from the TALKBACK
MIC IN jack, and determines the bus to be output.
q Talkback knob
Adjusts the talkback level.
w AUX1-4 switch and indicator
Turning this switch on sends the signal from the TALKBACK
MIC IN jack to the AUX1 to AUX4 buses.
e STEREO switch and indicator
Turning this switch on sends the signal from the TALKBACK
MIC IN jack to the STEREO L/R bus.
GROUP section
This section adjusts the level and controls the flow of the signals
from the four GROUP buses. While the signal from each GROUP
bus is always sent to the corresponding GROUP OUT jack, you
are also free to use the ST and AFL switches to selectively send
these groups to the STEREO and AFL buses.
q PAN knob
Determines how the signal from the GROUP 1-4 buses is posi-
tioned on the STEREO L/R buses when turning the ON switch
(w)
on.
w ON switch
Turning this switch on enables the GROUP fader. When the
switch is turned on, the switch’s lamp comes on.
e ST (Stereo) switch
Turning this switch on sends the signal adjusted with the
GROUP fader
(t)
via the PAN knob
(q)
to the STEREO L/R
bus.
r AFL (After-Fader Listen) switch and indictor
When the AFL switch is on, the indicator will light and the sig-
nal after the GROUP fader
(t)
is output to the MONITOR
OUT and PHONES jacks for monitoring.
t GROUP faders (1-4)
These adjust the level of the signal sent to the corresponding
GROUP OUT 1-4 jacks.
NOTE
• The PFL signal has priority when both the PFL switch and
AFL switch are on. To monitor the post-fader signal, make
sure to turn off all PFL switches.
• If the PFL (preferred) is enabled, the AFL indicator does not
light, even if the AFL switch is pressed.
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
Yamaha MGP24X Kullanım kılavuzu
- Kategori
- Tamamlayıcı müzik ekipmanı
- Tip
- Kullanım kılavuzu
- Bu kılavuz için de uygundur
Diğer dillerde
- español: Yamaha MGP24X Manual de usuario
- français: Yamaha MGP24X Manuel utilisateur
- italiano: Yamaha MGP24X Manuale utente
- svenska: Yamaha MGP24X Användarmanual
- čeština: Yamaha MGP24X Uživatelský manuál
- polski: Yamaha MGP24X Instrukcja obsługi
- Deutsch: Yamaha MGP24X Benutzerhandbuch
- português: Yamaha MGP24X Manual do usuário
- English: Yamaha MGP24X User manual
- dansk: Yamaha MGP24X Brugermanual
- русский: Yamaha MGP24X Руководство пользователя
- suomi: Yamaha MGP24X Ohjekirja
- Nederlands: Yamaha MGP24X Handleiding
- română: Yamaha MGP24X Manual de utilizare