Yamaha HTR-5460 El kitabı

Kategori
AV alıcıları
Tip
El kitabı
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia ID
V722860
HTR-5460
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
U C A
OWNER’S MANUAL
MODE D’EMPLOI
0100HTR5460(UCA)-cv1/4 1/16/1, 11:03 AM1
II
II
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the operating
instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a cart
or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
unit and cart combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8 Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation. For
example, the unit should not be situated on a bed, sofa, rug,
or similar surface, that may block the ventilation openings; or
placed in a built-in installation, such as a bookcase or cabinet
that may impede the flow of air through the ventilation
openings.
9 Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating instructions or
as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating instructions.
All other servicing should be referred to qualified service
personnel.
17 Power Lines – An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization – Precautions should be taken so
that the grounding or polarization is not defeated.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
I CAUTION
0101V620(UCA)_Cau_EN 1/16/1, 10:07 AM2
III
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
III
SAFETY INSTRUCTIONS
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers only)
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
Note to CATV system installer:
This reminder is provided to call the CATV system
installers attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
CAUTION II
0101V620(UCA)_Cau_EN 1/16/1, 10:07 AM3
IV
IV
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, 20 cm on the
right and left, and 10 cm at the back of this unit for
ventilation space — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may
cause electrical shock to the user and/or damage
to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal
injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Take care of this unit so that no foreign objects and/
or liquid drops inside this unit.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
19 VOLTAGE SELECTOR (China and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FREQUENCY STEP switch
(China and General models only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch
(locating at the rear) according to the frequency
spacing in your area.
North, Central and South America: 100 kHz/10 kHz
Other area: 50 kHz/9 kHz
Before setting this switch, disconnect the AC power
plug of this unit from the AC outlet.
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owners Manual in a safe place for future
reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
III CAUTION
0101V620(UCA)_Cau_EN 1/16/1, 10:07 AM4
1
EnglishINTRODUCTION PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
INTRODUCTION
CONTENTS
INTRODUCTION
FEATURES............................................................ 2
GETTING STARTED........................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS ........................ 4
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Description of the Numeric Buttons ........................ 7
Using the Remote Control........................................ 8
Front Panel Display .................................................. 9
Rear Panel .............................................................. 10
PREPARATION
SPEAKER SETUP .............................................. 11
Speakers to Be Used............................................... 11
Speaker Placement ................................................. 11
CONNECTIONS ................................................. 12
Before Connecting Components ............................ 12
Connecting Audio Components ............................. 12
Connecting an External Decoder ........................... 13
Connecting Video Components .............................. 14
Connecting the Speakers ........................................ 16
IMPEDANCE SELECTOR Switch ....................... 18
Connecting the Power Supply Cords ..................... 18
ON-SCREEN DISPLAY (OSD) ......................... 19
OSD Modes ............................................................ 19
Selecting the OSD Mode........................................ 19
SPEAKER MODE SETTINGS ......................... 20
Summary of SPEAKER SET Items
1A through 1E .................................................... 20
ADJUSTING THE SPEAKER OUTPUT
LEVELS ........................................................... 21
Before You Begin ................................................... 21
Using the Test Tone (TEST DOLBY SUR.) .......... 21
BASIC OPERATION
BASIC PLAYBACK ........................................... 23
Input Modes and Indications .................................. 25
Selecting a Sound Field Program ........................... 27
Normal Stereo Reproduction.................................. 28
TUNING............................................................... 29
Connecting the Antennas........................................ 29
Automatic (or Manual) Tuning .............................. 30
Presetting Stations .................................................. 31
Tuning in to a Preset Station .................................. 32
Exchanging Preset Stations .................................... 33
BASIC RECORDING......................................... 34
ADVANCED OPERATION
SET MENU .......................................................... 35
Adjusting the Items on the SET MENU................. 35
1 SPEAKER SET (speaker mode settings)........... 36
2 L/R BALANCE (balance of the left and right
main speakers) ................................................... 38
3 HP TONE CTRL (headphone tone control) ....... 39
4 I/O ASSIGNMENT ............................................ 39
5 INPUT MODE (initial input mode) ................... 39
6 DOLBY D. SET (Dolby Digital set) .................. 40
7 DTS SET (DTS LFE level) ................................ 40
8 SP DELAY TIME............................................... 41
9 DISPLAY SET ................................................... 41
10MEMORY GUARD ........................................... 41
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS...................................................... 42
SLEEP TIMER.................................................... 43
Setting the Sleep Timer .......................................... 43
Canceling the Sleep Timer ..................................... 43
REMOTE CONTROL FEATURES .................. 44
Selector Dial ........................................................... 44
Commonly Used Buttons in Any Position of the
Selector Dial....................................................... 45
Controlling the Components Connected
to This Unit ........................................................ 45
Button Names and Functions in Each Position ...... 46
Setting the Manufacturer Code .............................. 49
Returning to the Factory Setting ............................ 50
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM ............................. 51
Hi-Fi DSP Programs............................................... 51
CINEMA DSP Programs ........................................ 51
SOUND FIELD PROGRAM PARAMETER
EDITING ......................................................... 54
What is a sound field? ............................................ 54
Sound Field Program Parameters ........................... 54
Changing Parameter Settings ................................. 55
Resetting a Parameter to the Factory-set Value ...... 55
Sound Field Parameter Descriptions ...................... 56
APPENDIX
TROUBLESHOOTING ..................................... 59
SPECIFICATIONS ............................................. 64
GLOSSARY ......................................................... 65
INDEX .................................................................. 67
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM1
2
FEATURES
Sophisticated AM/FM Tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
Other Features
96-kHz/24-bit D/A Converter
“SET MENU” which Provides You with
10 Items for Optimizing This Unit for Your
Audio/Video System
Test Tone Generator for Easier Speaker Balance
Adjustment
6-Channel External Decoder Input for Other
Future Formats
BASS EXTENSION Button for Reinforcing
Bass Response
On Screen Display Function Helpful in
Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Optical and Coaxial Digital Audio Signal Jacks
Sleep Timer
Remote Control with Preset Manufacturer Codes
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases
when the button names differ between the main unit and the remote control, the button name on the remote control
is given in parentheses in this manual.
Built-in 5-Channel Power Amplifier
Minimum RMS Output Power
(0.06% THD, 20 Hz – 20 kHz)
[U.S.A. and Canada models]
Main: 100 W + 100 W (8 )
Center: 100 W (8 )
Rear: 100 W + 100 W (8 )
[Australia, Singapore, China and General
models]
Main: 90 W + 90 W (8 )
Center: 90 W (8 )
Rear: 90 W + 90 W (8 )
Maximum Power (EIAJ)
(10% THD, 1 kHz)
[China and General models]
Main: 115 W + 115 W (8 )
Center: 115 W (8 )
Rear: 115 W + 115 W (8 )
Multi-Mode Digital Sound Field
Processing
DTS Decoder
Dolby Pro Logic Decoder
Dolby Digital Decoder
Hi-Fi DSP
CINEMA DSP: Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital
or DTS
Virtual CINEMA DSP
SILENT CINEMA
Manufactured under license from Dolby Laboratories.
“Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby
Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All Rights Reserved.
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM2
3
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
Remote control
Installing Batteries in the Remote
Control
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
Notes on batteries
Change the batteries periodically.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
Batteries (4)
(AAA, R03, UM-4)
Indoor FM antenna
(U.S.A., Canada, China and
General models)
AM loop antenna
Quick Reference Card
Changing batteries
As the batteries lose power, the operating range of the
remote control decreases and the indicator does not flash
or its light becomes dim. When you notice any of these
conditions, change all of the batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code that may have
been cleared.
Note
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
1
2
3
A/B/C/D/E
Quick Reference Card
(Australia and
Singapore models)
Connection guide
0102V620(UCA)_1-10_EN 1/16/1, 1:41 PM3
4
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on or sets this unit in the standby mode. When you
turn on this unit, you will hear a click and there will be a
4 to 5-second delay before this unit can reproduce sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit.
4 INPUT MODE
Selects the mode of input for sources that send two or
more types of signals to this unit (see page 25 for details).
You cannot control the input mode when you select 6CH
INPUT as the input source.
5 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
6 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons on the remote control).
7 BASS EXTENSION ON/OFF
When pushed in (ON), this feature boosts the bass
frequency of the left and right main speakers by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if “1B MAIN
SP” on the SET MENU is set to SMALL and “1D LFE/
BASS OUT” is set to SWFR.
SILENT VIDEO AUX
PHONES S VIDEO VIDEO L AUDIO R OPTICAL
6CH INPUTINPUT MODE
INPUT
VOLUME
PRESET
/TUNING
EDIT
MEMORYEFFECT
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
FM/AM
DSP
PROGRAM
BASS TREBLE SPEAKERS
AB
OFFONOFFON
STANDBY
/ON
DIGITAL
BASS
EXTENSION
+
+
SURROUND
DIGITAL
1 2
3
4
5
6
7 8
9
0
q
i
o
p
e
yu
r
t
w
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM4
5
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
8 BASS
Adjusts the low-frequency response for the left and right
main speakers.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
9 TREBLE
Adjusts the high-frequency response for the left and right
main speakers.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.
0 SPEAKERS A/B
When pushed in (ON), these buttons turn on the set of
main speakers connected to the A and/or B terminals on
the rear panel.
q EFFECT
Switches the effect speakers (center and rear) on and off.
If you turn off the output of these speakers by using
EFFECT, all Dolby Digital and DTS audio signals except
for the LFE channel are directed to the main left and right
channels.
When Dolby Digital or DTS signals are mixed, the left
and right main channel signal levels may not match.
w DSP PROGRAM
Switches the function of the multi jog knob for selecting
DSP program.
e PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the speakers.
r Multi jog knob
Selects the tuning frequency in the tuning mode.
Selects the preset station after pressing PRESET/
TUNING (EDIT) to display “ z ” in the tuning mode.
Selects the DSP program after pressing DSP PROGRAM.
t VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
y PRESET/TUNING (EDIT)
Switches the function of the multi jog knob between
selecting a preset station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
u FM/AM
Switches the reception band between FM and AM.
i MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning (for
FM stations only).
o TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the “AUTO” indicator lights up on the front panel
display again. To select the manual tuning mode, press
this button so that the “AUTO” indicator does not light
up.
p INPUT l / h
Selects the input source (CD, TUNER, MD/CD-R, DVD,
D-TV/CBL, VCR 1, PHONO, V-AUX, VCR 2/DVR) you
want to listen to or watch.
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM5
6
CONTROLS AND FUNCTIONS
A/B/C/D/E
TV INPUT
TV VOLUME
TV POWER
EFFECT
e
r
1
2
3
4
5
6
7
9
8
q
w
0
t
y
u
i
o
Remote Control
This section describes the basic operation of this unit with
the remote control. First, set the selector dial to the AMP/
TUN position. See “REMOTE CONTROL FEATURES”
for full details.
Select the
AMP/TUN
position.
1 DSP
Switches the function of the numeric buttons to the DSP
program selector.
2 Indicator window
Shows the name of components which can be controlled.
3 Numeric buttons (Input selector buttons)
These buttons select the input source.
See “Description of the Numeric Buttons” for the
numeric buttons.
4 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
5 TEST
Outputs the test tone.
6 ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
7 j / i (–/+)
Adjust DSP program parameters and SET MENU items.
–/+ is displayed on the on-screen display.
8 LEVEL
Selects the effect speaker channel (center, rear and
subwoofer) so you can adjust their output level
independently.
9 SLEEP
Sets the sleep timer.
0 INPUT
Switches the function of the numeric buttons to the input
selector.
q Indicator
Flashes while the remote control is sending signals.
w Selector dial
Turn this dial to select the position for the component to
be controlled. (The proper code must be set up for your
component. See “Setting the Manufacture Codes”.) When
a position is selected, the remote control is set to that
component operation mode.
e A/B/C/D/E, PRESET –/+
These buttons are used to select a preset station.
A/B/C/D/E: To select one of 5 preset station groups (A
to E)
PRESET –/+: To select a preset station number (1 to 8)
r u/d
Select DSP program parameters and SET MENU items.
t SET MENU
Enters the SET MENU.
y POWER
Turns on the power of this unit.
u STANDBY
Sets this unit in the standby mode.
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM6
7
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
A
B
i VOLUME +/–
Increases or decreases the volume level.
o MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
EFFECT
Switches the effect speakers (center and rear) on and off
in the following cases:
When the selector dial is set to the DSP/TUN position.
While the indicator is lit for about 3 seconds after
pressing DSP.
Description of the Numeric
Buttons
The numeric buttons function in various ways depending
on the position of the selector dial or the combination of
other instructions.
When selecting an input source
Input selector
buttons
1 Press INPUT regardless of the position of
the selector dial.
The indicator lights up for about 3 seconds.
2 You can select an input source with the
numeric buttons and 6CH INPUT while the
indicator is lit.
When selecting a DSP program
and turning on or off the effect
speakers (center and rear)
DSP program
group buttons
A
1 Press DSP regardless of the position of the
selector dial.
The indicator lights up for about 3 seconds.
2 You can select a DSP program with the
numeric buttons and turn on or off the effect
speakers (center and rear) by pressing
EFFECT while the indicator is lit.
B
1 Set the selector dial to the DSP/TUN
position.
2 You can select a DSP program directly with
the numeric buttons and turn on or off the
effect speakers (center and rear) by pressing
EFFECT.
6CH INPUT
EFFECT
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM7
8
CONTROLS AND FUNCTIONS
When selecting a preset station
number
1 Set code number “0023” in the AMP/TUN (or
DSP/TUN) position.
See “Setting the Manufacturer Code” for setting the
code.
2 Set the selector dial to the AMP/TUN (or
DSP/TUN) position.
3 You can select a preset station number
directly with the numeric buttons (1 to 8).
See “Tuning in to a Preset Station”.
Using the Remote Control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
DIGITAL
+
+
SURROUND
DIGITAL
30° 30°
Approximately 6 m (20 feet)
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM8
9
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
Front Panel Display
1 t indicator
Lights up when the built-in DTS decoder is on.
2 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP.
3 g and o indicators
Light up according to the type of Dolby signals this unit
is reproducing. “ g ” lights up when the built-
in Dolby Digital decoder is on. “ o ” lights up
when the built-in Dolby Pro Logic decoder is on.
4 Input source indicator
Shows the current input source with a cursor.
5 TUNED indicator
Lights up when this unit tunes in to a station.
6 STEREO indicator
Lights up when the unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.
7 AUTO indicator
Shows that this unit is in the automatic tuning mode.
8 MEMORY indicator
Flashes to show a station can be stored.
9 x indicator
Lights up when you select a DSP program.
0 v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
q Headphones indicator
Lights up when headphones are connected.
w DSP program indicators
The name of the selected DSP program lights up when the
ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or q/DTS SURROUND DSP program is
selected.
e Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
r VOLUME level indicator
Indicates the volume level.
t SLEEP indicator
Lights up while the sleep timer is on.
dB
ms
PCM
DSP
DIGITAL
PRO LOGIC
A
SP
B
VIRTUAL
DOLBY DIGITAL
PRO LOGIC DTS
MOVIE THEATER 1
2
ENTERTAINMENT
TUNED
STEREO AUTO
MEMORY
SLEEP
VOLUME
CDTUNER PHONO
MD/CD-R
DVD
D-TV/CBL
VCR 1
VCR2/DVR
V-AUX
1 2
3
4
5 6
7
8
9
0 q
w
e
r t
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM9
10
CONTROLS AND FUNCTIONS
Rear Panel
1 DIGITAL OUTPUT jacks
2 DIGITAL INPUT jacks
3 GND terminal
See page 12 for connection information.
4 6CH INPUT jacks
See page 13 for connection information.
5 Antenna input terminals
See page 29 for connection information.
6 Video component jacks
See pages 14 and 15 for connection information.
7 Speaker terminals
See pages 16 and 17 for connection information.
8 AC power cord
Connect to a power outlet.
9 AC OUTLET(S)
Use these outlets to supply power to your other audio/
video components (see page 18).
0 Audio component jacks
See pages 12 and 13 for connection information.
q SUBWOOFER jack
See page 17 for connection information.
w IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance. Set this unit in the standby mode
before you change the setting of this switch (see page 18).
China and General models only
FREQUENCY STEP switch
See page 29.
VOLTAGE SELECTOR
See page 18.
1
2
4 5
6 7
8 9
q w
0
3
SWITCHED
100W MAX.
TOTAL
SPEAKERS
MAIN
+
R L
A
+
B
CENTER
+
REAR
(SURROUND)
R
L
+ ––+
DVD
MONITOR
OUT
D-TV/CBL
YPB/CB PR/CR COMPONENT VIDEO
S VIDEO
VIDEO
MONITOR OUT
DVD
DVD
DVD
D-TV/CBL
D-TV/CBL
D-TV/CBL
IN
VCR 1
OUT IN
VCR 2
/DVR
OUT
VIDEO SIGNAL
AUDIO SIGNAL
SUB
WOOFER
OUTPUT
IN
VCR 1
OUT IN
VCR 2/DVR
OUT
OUT(REC)
IN(PLAY)
CD
PHONO
MD/CD-R
MD/CD-R
MD/CD-R
R
L
DIGITAL
OUTPUT
OPTICAL
OPTICAL
COAXIAL
AM ANT GND
FM ANT
75
UNBAL.
TUNER
GND
MAIN
CENTER
SUB WOOFER
SURROUND
DIGITAL
INPUT
6CH INPUT
CD
R
L
R
L
AC OUTLETS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
(U.S.A. model)
0102V620(UCA)_1-10_EN 1/16/1, 11:19 AM10
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Speakers to Be Used
This unit has been designed to provide the best sound-
field quality with a 5-speaker system, using left and right
main speakers, left and right rear speakers, and a center
speaker. If you use different brands of speakers (with
different tonal qualities) in your system, the tone of a
moving human voice and other types of sound may not
shift smoothly. We recommend that you use speakers
from the same manufacturer to ensure even tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers.
For precise sound localization, however, it is ideal to use
high-performance models that can reproduce sounds over
the full range for the center speaker and the rear speakers.
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main
speaker (L)
Center speaker
Main speaker (R)
Rear speaker (R)
Rear speaker (L)
1.8 m
Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (approx. 6 feet)
above the floor.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
“1A CENTER SP” on the SET MENU is set to NONE.
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
Please use magnetically shielded speakers. Sometimes
a video monitor may be adversely affected even when
magnetically shielded speakers are used. Separate the
speakers from the monitor if this happens.
PREPARATION
Subwoofer
0103V620(UCA)_11-17_EN 1/16/1, 11:19 AM11
12
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc.
After you have completed all connections, check them again to make sure they are correct.
Connecting Audio Components
Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals.
y
You can designate the input for each digital jack according to
your component by using “4 I/O ASSIGNMENT” on the SET
MENU.
About the dust protection cap
Pull out the cap from the optical jack
before you connect the fiber optic cable.
Do not discard the cap. When you are not
using the optical jack, be sure to put the
cap back in place. This cap protects the
jack from dust.
Note
The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
Connecting a turntable
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an inline boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
The GND terminal does not electrically ground the turntable. It
simply reduces noise in the signal. In some cases, you may
hear less noise if you do not connect to the GND terminal.
Connecting a CD player
y
The COAXIAL jack is available for a CD player which has a
coaxial digital output jack.
When you connect a CD player to both the analog and digital
jacks, priority is given to the input signals from the digital jack.
Connecting an MD recorder, CD
recorder or tape deck
y
When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
Notes
When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit
may distort the sound from other components.
Since digital output and analog output (REC OUT) are
independent of each other, the analog signal is output only to
the analog jack, while the digital signal is output only to the
digital jack.
0103V620(UCA)_11-17_EN 1/16/1, 11:19 AM12
13
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DVD
MONITOR
OUT
D-TV/CBL
YP
B
/C
B
P
R
/C
R
COMPONENT VIDEO
S VIDEO
VIDEO
MONITOR OUT
DVD
DVD
DVD
D-TV/CBL
D-TV/CBL
D-TV/CBL
IN
VCR 1
OUT IN
VCR 2
/DVR
OUT
VIDEO SIGNAL
AUDIO SIGNAL
SUB
WOOFER
OUTPUT
IN
VCR 1
OUT IN
VCR 2/DVR
OUT
OUT(REC)
IN(PLAY)
CD
PHONO
MD/CD-R
MD/CD-R
MD/CD-R
R
L
DIGITAL
OUTPUT
OPTICAL
OPTICAL
COAXIAL
AM ANT GND
FM ANT
75
UNBAL.
TUNER
GND
MAIN
CENTER
SUB WOOFER
SURROUND
DIGITAL
INPUT
6CH INPUT
CD
R
L
R
L
L R
L R
L
R
C
L
R
L
R
OO
L R
OUTPUT
GND
OUTPUT
COAXIAL
OUTPUT
SUBWOOFER
OUTPUT
CENTER
OUTPUT
MAIN
OUTPUT
SURROUND
OUTPUT
INPUT OUTPUT
OPTICAL
OUTPUT
OPTICAL
INPUT
L
R
C
O
MD recorder
or CD recorder
indicates signal direction
indicates coaxial cables
CD player
Turntable
External decoder
indicates left analog cables
indicates right analog cables
indicates optical cables
(U.S.A. model)
Connecting an External Decoder
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
When you select 6CH INPUT as the input source, changing
items 1A to 1E on the SET MENU is not affected.
0103V620(UCA)_11-17_EN 1/16/1, 11:19 AM13
14
CONNECTIONS
YPB/CB PR/CR
Connecting Video Components
About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
B
/C
B
, P
R
/C
R
) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, C
B
, C
R
/Y, P
B
, P
R
/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
VIDEO jack (composite)
S VIDEO jack
COMPONENT VIDEO jacks
y
Each type of video jack works independently. Signals input
through the composite video, S-video and component jacks are
output through the corresponding composite video, S-video,
and component jacks, respectively.
If you make S-video connections to this unit, it is not necessary
to make composite video connections. If both types of
connections are made, this unit gives priority to the S-video
signal.
You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using “4 I/O
ASSIGNMENT” on the SET MENU.
Notes
Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
When you are using the COMPONENT VIDEO jacks, check the details in the owners manual that came with the component being
connected.
VIDEO AUX jacks (on the front panel)
These jacks are used to connect any video input source
such as a game console to this unit.
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
VIDEO AUX
S VIDEO VIDEO L AUDIO R OPTICAL
Game console
0103V620(UCA)_11-17_EN 1/16/1, 11:19 AM14
15
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DVD
MONITOR
OUT
D-TV/CBL
YPB/CB PR/CR COMPONENT VIDEO
S VIDEO
VIDEO
MONITOR OUT
DVD
DVD
DVD
D-TV/CBL
D-TV/CBL
D-TV/CBL
IN
VCR 1
OUT IN
VCR 2
/DVR
OUT
VIDEO SIGNAL
AUDIO SIGNAL
SUB
WOOFER
OUTPUT
IN
VCR 1
OUT IN
VCR 2/DVR
OUT
OUT(REC)
IN(PLAY)
CD
PHONO
MD/CD-R
MD/CD-R
MD/CD-R
R
L
DIGITAL
OUTPUT
OPTICAL
OPTICAL
COAXIAL
AM ANT GND
FM ANT
75
UNBAL.
TUNER
GND
MAIN
CENTER
SUB WOOFER
SURROUND
DIGITAL
INPUT
6CH INPUT
CD
R
L
R
L
V
V
S VIDEO
INPUT
S
S VIDEO
OUTPUT
L
R
S
L
R
L
R
OPTICAL
OUTPUT
VIDEO
OUTPUT
COMPONENT
OUTPUT
AUDIO OUTPUTAUDIO OUTPUT VIDEO INPUT
VIDEO
OUTPUT
AUDIO
INPUT
V
S
O
O
OPTICAL
OUTPUT
L
R
S VIDEO
OUTPUT
AUDIO
OUTPUT
VIDEO
OUTPUT
V
S
COMPONENT
OUTPUT
S
V
S VIDEO
INPUT
VIDEO
INPUT
COMPONENT
INPUT
S VIDEO
OUTPUT
L
S
R
V
O
DVD player
TV/digital TV or
cable TV/satellite
tuner
VCR 1 or VCR 2/
DVR (digital video
recorder)
(U.S.A. model)
indicates signal direction
indicates left analog cables
indicates right analog cables
indicates optical cables
indicates video cables
indicates S-video cables
Monitor
When using an LD player
Connect the LD player output to the DVD jack.
If the LD player has an OPTICAL digital output jack, connect it to this unit’s OPTICAL DVD jack. If it has analog
jacks, connect it to the analog DVD jacks. If it has an “RF OUTPUT jack” to output a Dolby Digital RF signal (AC-3),
use a commercially available RF demoduclator and connect it to the OPTICAL DVD jack.
If connecting a DVD player and an LD player, connect the LD player to the digital input jack (ex. D-TV/CBL) or the
analog input jack (D-TV/CBL, VCR 1 or VCR 2/DVR). For details on connections and operations, refer to the
instruction manual for the LD player.
Note that this unit’s remote control can be used to operate the LD player by setting the corresponding manufacturer
code for the DVD/LD position.
0103V620(UCA)_11-17_EN 1/17/1, 4:38 PM15
16
CONNECTIONS
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage the unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approx. 10 mm (3/8”) of insulation
from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
12
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
2
1
3
Red: positive (+)
Black: negative (–)
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
10 mm (3/8”)
y
(U.S.A., Canada, Australia, China and General models only)
Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
Banana plug
0103V620(UCA)_11-17_EN 1/16/1, 11:19 AM16
1 / 1

Yamaha HTR-5460 El kitabı

Kategori
AV alıcıları
Tip
El kitabı