Monster T5 Kullanım kılavuzu

01

EN

T5 V23.2

USER MANUAL

BENUTZERHANDBUCH

KULLANIM KILAVUZU

MANUAL DE USUARIO

MANUEL DE L’UTILISATEUR

MANUALE UTENTE

 

EN

02

This user manual is a brief introduction to

getting your system started.

This is a supplement, and not a substitute for

the expanded English language User’s Manual

in Adobe Acrobat format on the Device Drivers

& Utilities + User’s Manual disc supplied with

your computer. This disc also contains the

drivers and utilities necessary for the proper

operation of the computer.

(Note: The company reserves the right to

revise this publication or

to change its contents without notice).

Some or all of the computer’s features may

already have been setup.

If they aren’t, or you are planning to

re-configure (or re-install)

portions of the system, refer to the

expanded User’s Manual.

The Device Drivers & Utilities + User’s Manual

disc does not contain an operating system.

Please pay careful attention to the full

regulatory notices and safety information

contained in the expanded User’s Manual on

the Device Drivers & Utilities + User’s Manual

disc.

About This

User Guide

Regulatory and

Safety Information

T5 V23.2

USER MANUAL

03

EN

Intel is a trademark/registered trademark of Intel Corporation.

Windows is a registered trademark of Microsoft Corporation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired operation.

The computer is quite rugged, but it can be damaged. To prevent this,

follow these suggestions.

• Don’t drop it, or expose it to shock. If the computer falls, the case and

the components could be damaged.

• Keep it dry, and don’t overheat it. Keep the computer and power supply away

from any kind of heating element. This is an electrical appliance. If water or any

other liquid gets into it, the computer could be badly damaged.

• Avoid interference. Keep the computer away from high capacity transformers,

electric motors, and other strong magnetic fields. These can hinder proper

performance and damage your data.

• Follow the proper working procedures for the computer. Shut the computer

down properly and don’t forget to save your work. Remember to periodically

save your data as data may be lost.

Trademarks

Instructions for Care and Operation

FCC Statement

EN

04

Do not attempt to service the computer yourself. Doing so may violate your

warranty and expose you and the computer to electric shock. Refer all servicing

to authorized service personnel. Unplug the computer from the power supply.

Then refer servicing to qualified service personnel under any of the following

conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to any liquids.

• If the computer does not work normally when you follow the operating

instructions.

• If the computer has been dropped or damaged.

(do not touch the poisonous liquid if the panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

• Only use an AC/DC adapter approved for use with this computer.

• Use only the power cord and batteries indicated in this manual. Do not dispose

of batteries in a fire. They may explode. Check with local codes for possible

special disposal instructions.

• Do not continue to use a battery that has been dropped, or that appears

damaged (e.g. bent or twisted) in any way. Even if the computer continues to

work with a damaged battery in place, it may cause circuit damage, which may

possibly result in fire.

• Make sure that your computer is completely powered off before putting it into a

travel bag (or any such container).

• Before cleaning the computer, make sure it is disconnected from any external

power supplies, peripherals and cables.

• Use a soft clean cloth to clean the computer, but do not apply cleaner directly

to the computer. Do not use volatile (petroleum distillates) or abrasive cleaners

on any part of the computer.

• Do not try to repair a battery pack. Refer any battery pack repair or,

replacement to your service representative or qualified service personnel.

Servicing

Safety Information

05

EN

Note the following information which is specific to Polymer/Lithium-Ion

batteries only, and where applicable, this overrides the general battery

precaution information.

• Polymer/Lithium-Ion batteries may experience a slight expansion or swelling,

however this is part of the battery’s safety mechanism and is not a cause for

concern.

• Use proper handling procedures when using Polymer/Lithium-Ion batteries.

Do not use Polymer/Lithium-Ion batteries in high ambient temperature

environments, and do not store unused batteries for extended periods.

• If you are working in areas of low temperature use the AC/DC adapter to

power the computer.

The product that you have purchased contains a rechargeable battery.

The battery is recyclable. At the end of its useful life, under various state and

local laws, it may be illegal to dispose of this battery into the municipal waste

stream. Check with your local solid waste officials for details in your area for

recycling options or proper disposal. Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type recommended

by the manufacturer. Discard used battery according to the

manufacturer’s instructions.

• Note that in computer’s featuring a raised electro-plated logo, the logo is

covered by a protective adhesive. Due to general wear and tear, this adhesive

may deteriorate over time and the exposed logo may develop sharp edges.

Be careful when handling the computer in this case, and avoid touching the

raised electro-plated logo. Avoid placing any other items in the carrying bag

which may rub against the top of the computer during transport.

If any such wear and tear develops contact your service center.

Polymer/Lithium-Ion Battery Precautions

Battery Disposal & Caution

EN

06

Figure 1 - Opening the Lid/Computer with AC/DC Adapter Plugged-In

1. Remove all packing materials.

2. Place the computer on a stable surface.

3. Securely attach any peripherals you want to use with the computer

(e.g. keyboard and mouse) to their ports.

4. When first setting up the computer use the following procedure

(as to safeguard the computer during shipping, the battery will be locked to not

power the system until first connected to the AC/DC adapter and initially set up

as below):

• Attach the AC/DC adapter cord to the DC-In jack on the rear of the computer,

then plug the AC power cord into an outlet, and connect the AC power cord to

the AC/DC adapter. The battery will now be unlocked.

5. Use one hand to raise the lid to a comfortable viewing angle

(do not exceed 130 degrees); use the other hand (as illustrated in Figure 1) to

support the base of the computer (Note: Never lift the computer by the lid).

6. Press the power button to turn the computer “on”.

System Startup

130°

07

EN

Your computer may already come with system software pre-installed.

Where this is not the case, or where you are re-configuring your computer

for a different system, you will find this manual refers to Microsoft Windows 11.

You need to setup RAID before installing your Windows operating

system (see RAID Setup page).

Your solid state drives (SSDs) can be set up in RAID mode

(for increased performance or protection). Note that setting up your solid state

drives in RAID mode needs to be done prior to installing the Windows OS.

Do not change the mode unless you intend to reinstall your operating system,

and make sure you back up all necessary files and data before doing so.

To configure your RAID (Redundant Array of Independent Disks) system in

Striping (RAID 0) or Mirroring (RAID 1) mode (see Table 1) you will require two

identical solid state drives.

Note that you should always shut your computer down by choosing the

Shut down command in Windows (see below). This will help prevent hard disk or

system problems.

1. Click the Start Menu icon .

2. Click the Power item .

3. Choose Shut down from the menu .

System Software

RAID Support

RAID Setup

Shut Down

EN

08

RAID 0

(at lease two

SSDs needed)

Identical drives reading and writing data in parallel to

increase performance. RAID 0 implements a striped disk

array and the data is broken into blocks and each block is

written to a separate drive.

Identical drives in a mirrored configuration used to protect

data. Should a drive that is part of a mirrored array fail, the

mirrored drive (which contains identical data) will handle all

the data. When a new replacement drive is installed, data

to the new drive is rebuilt from the mirrored drive to restore

fault tolerance.

RAID 1

(at lease two

SSDs needed)

RAID Level Description

Table 1 - RAID Description

Prepare the following before setting up your PCIe SSDs in RAID mode:

• The Microsoft Windows 11 OS on a DVD or USB flash drive.

• A connected external DVD drive.

• Two identical PCIe solid state drives.

• The Device Drivers & Utilities + User’s Manual disc.

• A USB Flash drive or external USB hard disk drive.

Note: All SSDs in a RAID should be identical (the same size and brand) in order to

prevent unexpected system behavior.

1. Go to the operable computer and copy the f6mdflpy-x64 folder from the

location below on the Device Drivers & Utilities + User’s Manual disc to the USB

Flash drive or external USB hard disk.

• Raid\F6\VMD\f6vmdflpy-x64\

2. Start-up your notebook computer and press F2 to enter the BIOS

and go to the Setup Utility.

3. Select the Advanced menu.

4. Select VMD Mode and select Enabled.

5. Press F10 to Save and Exit and select <Yes>.

6. After the computer restarts press F2 to enter the BIOS again and

go to the Setup Utility.

RAID Setup Procedure

09

EN

7. Go to Intel® Rapid Storage Technology (in the Advanced menu) and select

Create RAID Volume.

8. You can now setup your RAID volume using the installed SSDs.

9. Select Name and type a name of your choice for your RAID volume and

select <Yes>.

10. Select RAID Level and choose the RAID Level required (see Table 1) and

press Enter.

• RAID 0 (Stripe)

• RAID 1 (Mirror)

11. Go to any of the disks listed under Select Disks: and select a disk name.

12. Click on X to select the disk required.

13. You should select two identical SSDs to form your RAID volume.

14. If you have selected RAID 0 (Stripe) then you can adjust the Strip Size to your

requirements (It is recommended that you set the “Strip Size” to 128KB).

15. Select Create Volume (make sure you have selected your disks).

16. The system will list your RAID volume.

17. Press F10 to Save and Exit and select <Yes>, however note below.

• Make sure the Windows OS (DVD) is in the attached DVD drive or on a USB flash

drive and as the computer starts up it will automatically boot from the Windows

OS DVD or USB flash drive.

18. Click Next > Install Now to continue installing the operating system as normal

(see your Windows documentation if you need help on installing the Windows

OS).

19. Click to select Load Driver when the “Where do you want to install Windows?”

screen appears.

20. Click Browse and browse to the location you copied the files to on your USB

Flash drive or external USB hard disk (X: denotes your USB Flash drive or

external USB hard disk):

• X:\f6vmdflpy-x64 (for Windows 64bit)

21. Select both driver names and click Next.

22. Follow the on-screen instructions to install the Windows operating system.

23. Install the Windows drivers. Make sure you install the

Intel® Rapid Storage Technology (IRST) driver.

EN

10

1

4

5

6

7

33

2

System Map:

Front View With Display Open

Figure 2 -

Front View with

Display Open

1. Webcam

2. *Camera LED

*When the camera is in use, the LED will be illuminated.

3. Built-In Array Microphone

4. Display

5. Power Button

6. Keyboard

7. Touchpad & Buttons Note that the Touchpad and Buttons

valid operational area is that indicated

within the dotted lines above.

11

EN

LED Indicators

Table 2 - LED Indicators

The AC/DC Adapter is Plugged In

The Battery is Charging

The Computer is On

The Battery Has Reached

Critically Low Power Status

The Computer is in Sleep Mode

Storage Device Activity

Orange

Green

Blinking Green

Blinking Orange

Green

Icon Color Description

The LED indicators on the computer display helpful information

about the current status of the computer.

EN

12

Your notebook comes with a multi-color LED keyboard. You can change the color

for the multi-color LED keyboard. The keyboard has a numeric keypad for easy

numeric data input. Pressing Num Lk turns on/off the numeric keypad. It

also features function keys to allow you to change operational features instantly.

Function Keys Scr Lk & Num Lk

Fn Key Windows Logo Key Numeric

Keypad

Keyboard

The keyboard LED may be configured using the Fn + key combination outlined in

the table below.

Keyboard LED Illumination

Increase

Fn +

Keyboard LED Function key Combinations

Toggle the Keyboard LED

On/Off

Keyboard LED Illumination

Decrease

Launch the LED Keyboard

Application

Table 3 - Keyboard LEDs

13

EN

Play/Pause (in Audio/Video Programs)

Turn Display Backlight Off

(Press a key to or use touchpad to turn on)

Change Display Configuration

(Press a key to or use touchpad to turn on)

Touchpad Toggle

Volume Decrease/Increase

Mute Toggle

Fn +

Keys Function/Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the

Fn key is held down. In addition to the basic function key combinations, some

visual indicators are available when the Control Center driver is installed.

Fn +

Function Keys & Visual Indicators

The LED Keyboard application can be accessed by clicking the LED Keyboard icon

in the Control Center (or by pressing the Fn plus key). .

EN

14

Display Brightness

Decrease/Increase

Airplane Mode Toggle

Control Center Toggle

Scroll Lock Toggle

Microphone Toggle

Disable/Enable Flexikey®

Camera Power Toggle

Caps Lock Toggle

Number Lock Toggle

*Note: It is recommended that you use Maximum fan speed when

playing games.

Sleep Toggle

Fan Speed Control

Power Modes Toggle

Fn +

Keys Function/Visual Indicators

15

EN

1. LED Indicators

2. Security Lock Slot

3. Vent

4. USB 3.2 Gen 1 Type-A Port

5. USB 2.0 Port

6. Microphone-In Jack

7. 2-In-1 Audio Jack (Headphone /Microphone)

8. Speakers

9. MicroSD Card Reader

10. USB 3.2 Gen 2 Type-C Port

11. RJ-45 LAN Jack

Figure 3 - Front, Left & Right Views

2

1

3

4 5 6 7 8

89 10 11

To prevent your computer from overheating make sure nothing

blocks any vent while the computer is in use.

Overheating

Note that the combination audio jacks can support headphones or headsets

(i.e. a combination microphone/headphone).

1. When a device is plugged in to the combination audio jack a dialog

(“Which device did you plug in?”) box will pop-up.

System Map:

Front, Left & Right Views

Combination Audio Jacks (2-In-1 Audio Jacks)

EN

16

1. Vent

2. RJ-45 LAN Jack

3. Speakers

4. USB 3.2 Gen 2 Type-C Port

5. HDMI-Out Port

6. Mini DisplayPort 1.4

7. DC-In Jack

2. Make sure you select the correct device from the drop-down menu

corresponding to the device plugged-in (e.g. choose “Headset” if you have

plugged-in a headset and do not choose “Headphone” in this case),

and then click OK to save the setting.

3. If you are plugging in a microphone then use the Microphone-In Jack,

and do not use the combination audio jack.

Figure 4 -

Bottom & Rear Views

1

1 1

4 5 6 7

2

33

System Map:

Bottom & Rear Views

17

EN

Control Center

Do not remove any cover(s) and/or screw(s) for the purposes

of device upgrade as this may violate the terms of your warranty.

If you need to replace/remove the SSD/RAM etc., for any reason, please contact

your distributor/supplier for further information.

Bottom Cover Removal Warning

Run the Control Center from the Start menu in Windows . You can also press the

Fn + Esc key combination, or double-click the icon in the notification area of the

taskbar to access the Control Center. The Control Center provides quick access

to Power Modes, Fan settings, LED Keyboard configuration and the Flexikey

application.

The Flexikey® application is a quick hotkey configuration application,

which allows you to assign a single key to launch multiple key combinations,

or to create text macros and to disable certain keys. The application can also be

used to configure the mouse buttons to create hotkeys for gaming etc.

Click on the Flexikey icon in the Control Center to access the Flexikey®

application.

Flexikey® Application

Most of the apps, control panels, utilities and programs within Windows 11 can be

accessed from the Start Menu by clicking the icon in the taskbar in the lower left

corner of the screen (or by pressing the Windows Logo Key on the keyboard).

Right-click the Start Menu icon (or use the Windows Logo Key + X key combina-

tion) to bring up an advanced Context Menu of useful features such as Apps and

Features, Power Options, Task Manager, Search, File Explorer, Device Manager,

Computer Management and Network Connections etc.

Windows 11 Start Menu, Context Menu,

Taskbar, Control Panel and Settings

EN

18

The notification area of the taskbar is in the bottom right of the screen.

Some of the control panels and applications referred to throughout the course

of this manual can be accessed from here. Throughout this manual you will see

an instruction to open the Control Panel. To access the Control Panel, use the

Windows Logo Key + R key combination and type “Control Panel”.

You can pin the Control Panel tile to Start or taskbar.

The Settings item in the Start Menu (and also as an App) gives you quick access

to a number of system settings control panels allowing you to adjust settings for

System, Bluetooth & devices, Network & internet, Personalization, Apps,

Accounts, Time & language, Gaming, Accessibility, Privacy & security and

Windows Update.

Figure 5 -

Start Menu, Context Menu, Taskbar, Control Panel and Setting

The system features both an Intel’s Integrated GPU (forpower-saving) and an

NVIDIA’s discrete GPU (for performance).

Video Features

19

EN

Microsoft Hybrid Graphics is a seamless technology designed to get best

performance from the graphics system while allowing longer battery life,

without having to manually change settings. The computer’s operating system

(and some applications) will automatically switch between the integrated GPU

and the discrete GPU when required by the applications in use.

Microsoft Hybrid Graphics

Note that you can use external displays connected to the HDMI-Out port

and/or Mini DisplayPort. See your display device manual to see which formats

are supported.

All external and internal displays (up to 2 active displays) can be configured from

Windows by using the Display or System (in Settings) control panel or the Project

menu.

Display Devices

Configuring the Displays in Windows

To access the Display control panel in Windows:

To access the Intel® Graphics Command Center:

To access the NVIDIA Control Panel:

1. Right-click the desktop and select Display settings from the menu.

2. Choose the required display settings from the menus.

1. Access the Intel® Graphics Command Center from the Start menu in Windows.

1. Access the NVIDIA Control Panel from the Start menu in Windows.

EN

20

To configure the displays using the Display control panel:

To configure the displays using the Project menu:

1. Attach your external display(s) to the appropriate port, and turn it(them) on.

2. Right-click the desktop and select Display settings from the menu.

3. Click the Detect button.

4. The computer will then detect any attached displays.

5. You can configure up to 3 displays from the Multiple displays menu.

1. Attach your external display(s) to the appropriate

port, and turn it(them) on.

2. Press the + P (or Fn + F7) key combination.

3. Click on any one of the options from the menu to

select PC screen only, Duplicate, Extend or Second

screen only.

4. You can also click Connect to a wireless display

at the bottom of the Project screen and follow the

steps to connect to any wireless enabled display.

Figure 7 -

Display (Multiple displays)

Figure 6 - Project

Note that when 2 displays are connected. Displays may be configured in

Duplicate mode.

2 Connected Displays

Sayfa yükleniyor ...

Monster T5 Kullanım kılavuzu

Monster T5 Kullanım kılavuzu

Diğer dillerde