Dell PowerEdge C6300 El kitabı

Dell PowerEdge C6320

Getting Started

With Your System

Začínáme se systémem

Mise en route du système

Erste Schritte mit dem System

Τα πρώτα βήματα στο σύστημά σας

Rozpoczynanie pracy z systemem

Начало работы с системой

Početak rada sa sistemom

Procedimientos iniciales con el sistema

Sisteminizi Kullanmaya Başlarken

תליחת הדובעה םע תכרעמה

Scan to see how-to videos, documentation, and

troubleshooting information.

Naleznete zde videa s postupy, dokumentaci

a informace o řešení potíží.

Scannez pour voir des didacticiels vidéo, obtenir de la

documentation et des informations de dépannage.

Scannen, um Videos zu Hilfe und Anleitungen, Dokumentationen

und Informationen zur Fehlerbehebung zu sehen.

Αναζητήστε βίντεο για τον τρόπο χρήσης του συστήματος,

τεκμηρίωση και πληροφορίες για την αντιμετώπιση προβλημάτων.

Zeskanuj, aby wyświetlić instruktażowe filmy wideo

i informacje o rozwiązywaniu problemów.

Сканируйте, чтобы просмотреть обучающее видео,

документацию и информацию по устранению неисправностей.

Skenirajte da biste videli video uputstva, dokumentaciju

i informacije o rešavanju problema.

Escaneo para ver vídeos sobre procedimientos, documentación

e información para la solución de problemas.

Tarama nasıl yapılır videoları, belgeler ve

sorun giderme bilgilerini görmek için.

קורס ידכ תוארל עדימ יבגל ינוטרס הכרדה ,דועית ןורתפו תויעב.

Dell PowerEdge

C6320

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or

loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

copyright and intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the

United States and/or other jurisdictions. All other marks and names mentioned herein may be

trademarks of their respective companies.

Regulatory Model: B08S Regulatory Type: B08S003

2015 - 03 P/N CFK9F Rev. A00

6 | Getting Started With Your System

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as defined in

Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:

• Access can only be gained by service persons or by users who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

• Access is through the use of a tool or lock and key, or other means of security,

and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow

the safety instructions that came with the system.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist

you. To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the

rails. To avoid personal injury or damage to the system, you must

adequately support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire

safety grounding conductor is necessary for the rack installation.

The rack equipment must provide sufficient airflow to the system to

maintain proper cooling.

CAUTION: When installing rails in a square-hole rack it is important

to ensure that the square peg slides through the square holes.

Getting Started With Your System | 7

1 Push the latch release buttons on the midpoints of the end piece to open the

rail latches. See Figure 1.

2 Align the end pieces of the rails on the vertical rack flanges to seat the pegs

in the bottom hole of the first U and the top hole of the second U.

NOTE: The rails can be used in both square-hole (item 1 in the

following figure) and round-hole racks (item 2 in the following figure).

Figure 1. Pushing the Latch Release Buttons

NOTE: To remove the rails, push the latch release button on the

midpoints of the end piece and unseat each rail.

8 | Getting Started With Your System

3 Engage the end of the rails and release the latch release button to have the

latches locked in place. See Figure 2.

Figure 2. Releasing the Latch Release Buttons

4 On each vertical rack flange on the back, put two screw bases into the two

square holes right above the rail. See Figure 3.

5 Install the chassis stabilizer shipping brackets (optional) on the back rack

flanges.

Getting Started With Your System | 9

6 Install and tighten the screws.

NOTE: To transport systems already installed in the rack, ensure that

the two chassis stabilizer shipping brackets (optional) are in place.

Figure 3. Installing the Chassis Stabilizer Shipping Brackets

10 | Getting Started With Your System

7 Slide the system into the rack. See Figure 4.

8 Tighten the thumbscrews to secure the ears of the system to the front of the

rack flanges.

Figure 4. Installing the Chassis onto the Rack.

Getting Started With Your System | 11

Optional—Connecting the Keyboard, Mouse, and Monitor

Figure 5. Optional—Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug

into each connector. Be sure to tighten the screws (if any) on the monitor’s cable

connector.

NOTE: Note that the system supports only one USB port and a micro USB

port. If you require more than one USB outlet at a time, use USB Hub or

Adapter Cable.

12 | Getting Started With Your System

Connecting the Power Cable(s)

Figure 6. Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used, connect

the monitor’s power cable to the monitor. Plug the other end of the power cables into

a grounded electrical outlet or a separate power source such as an uninterrupted power

supply or a power distribution unit.

NOTE: The system supports both AC and HVDC power inputs. Your system

can support up to two 1400 W power supply units (200-240 VAC nominal

input voltage) or up to two 1600 W power supply units (200-240 VAC nominal

input voltage). 1400 W power supply unit is supported only for China.

Getting Started With Your System | 13

Turning on the System

Figure 7. Pressing the Power Button on the Front of the System

Figure 8. Pressing the Power Button on the Back of the System

Press the power button(s) either on the front or back of the system. The power indicators

should light green.

14 | Getting Started With Your System

Complete the Operating System Setup

To install an operating system for the first time, see the installation and configuration

documentation for your operating system. Be sure the operating system is installed

before installing hardware or software not purchased with the system.

NOTE: See dell.com/ossupport for the latest information on supported operating

systems.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document

or as a separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system components.

This document is available at dell.com/support/home.

Dell systems management application documentation provides information about

installing and using the systems management software. This document is available

online at dell.com/support/home.

For an immediate access to your system information:

1. Go to dell.com/support.

2. Enter your system service tag in the Enter your Service Tag field.

3. Click Submit.

The support page that lists the system manuals is displayed.

For more information about your system:

1. Go to dell.com/support.

2. Select your country from the drop-down menu on the top left corner of

the page.

a. Select your product category.

b. Select your product segment.

c. Select your product.

The support page that lists the various support categories is displayed.

NOTE: Always check for updates on dell.com/support/home and read the

updates first because they often supersede information in other documents.

Getting Started With Your System | 15

NOM Information (Mexico Only)

The following information is provided on the device described in this document in

compliance with the requirements of the official Mexican standards (NOM):

Importer Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number B08S

Supply voltage 200-240 V AC with 1400 W (for China

only) or 1600 W Power Supply Unit

Frequency 50/60 Hz

Current consumption 9 Amps with 1400 W Power Supply Unit

10 Amps with 1600 W Power Supply Unit

Technical Specifications

Processor Two Intel Xeon E5-2600 v3

Memory

Architecture 1600 MT/s, 1866 MT/s, or

2133 MT/s DDR4 Registered

DIMMs

Support for advanced ECC or

memory optimized operation

Memory module sockets Twelve 288-pin

16 | Getting Started With Your System

Memory module capacities (RDIMMs) 8 GB and 16 GB dual-rank

Minimum RAM

Maximum RAM

16 GB

Up to 256 GB

Power

NOTE: The system does not support a mixed installation of 1400 W and

1600 W power supply units.

NOTE: The 1400 W and 1600 W power supply units are hot swappable,

and supports hot swap in any condition if the system has the power

throttling feature.

AC power supply (per power supply)

Wattage 1400 W (for China only)

Voltage 200-240 VAC, 50/60 Hz, maximum

input current: 9 Amps

Heat dissipation 6024.376 BTU/hr maximum

Maximum inrush current

Initial In-rush Current cannot exceed

55 Amps (peak). Secondary In-rush

Current cannot exceed 25 Amps

(peak).

Wattage 1600 W

Voltage

200-240 VAC, 50/60 Hz, maximum

input current: 10 Amps

Getting Started With Your System | 17

Heat dissipation 6033.979 BTU/hr maximum

Maximum inrush current

Initial In-rush current and secondary

In-rush current cannot exceed

50 Amps (peak).

HVDC power supply (per power supply)

Wattage 1400 W (for China only)

Voltage 240 VDC, 50/60 Hz, maximum input

current: 9 Amps

Heat dissipation 5440.614 BTU/hr maximum

Maximum inrush current

Initial In-rush Current cannot exceed

55 Amps (peak). Secondary In-rush

Current cannot exceed 25 Amps

(peak).

Battery (per system board)

System battery CR 2032 3.0-V lithium ion coin cell

Physical

Height 8.68 cm (3.42 in)

Width 44.8 cm (17.6 in)

Depth 79.0 cm (31.1 in)

Weight (maximum configuration) 41 kg (90.38 lb)

(with 12*3.5” HDD)

39 kg (86.00 lb)

(with 24*2.5” HDD)

18 | Getting Started With Your System

Weight (empty) 15.7 kg (34.61 lb)

(with 2.5” HDD bay)

15.1 kg (33.29 lb)

(with 3.5” HDD bay)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating 10° to 35°C (50° to 95°F) with

a maximum temperature gradation

of 10°C per hour

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1°F/550 ft.

CAUTION: The maximum number of

memory modules and hard drives

supported on 1U node configuration,

with 135W and 145W processors,

depends on the power supply installed.

Storage –40° to 65°C (–40° to 149°F) with

a maximum temperature gradation of

20°C per hour

Relative humidity

Operating 20% to 80% (noncondensing) with

a maximum humidity gradation of

10% per hour

Storage 5% to 95% (noncondensing)

Maximum vibration

Operating 0.26 Grms at 5–350 Hz

Storage 1.88 Grms at 10–500 Hz for 15 min

Getting Started With Your System | 19

Maximum shock

Operating One shock pulse in the positive

z axis (one pulse on each side of the

system) of 31 G for 2.6 ms in the

operational orientation

Storage Six consecutively executed shock

pulses in the positive and negative x,

y, and z axes (one pulse on each side

of the system) of 71 G for up to 2 ms;

Six consecutively executed shock

pulses in the positive and negative x,

y, and z axes (one pulse on each side

of the system) of 27 G faired square

wave pulse with velocity change

at 235 inches/second

(597 centimeters/second)

Altitude

Operating -15.2 to 3,048 m

(-50 to 10,000 ft.)

Storage -15.2 to 10,668 m

(-50 to 35,000 ft.)

Airborne Contaminant Level

Class G1 as defined by

ISA-S71.04-1985

Sayfa yükleniyor ...

Dell PowerEdge C6300 El kitabı

Dell PowerEdge C6300 El kitabı

Diğer dillerde

İlgili Makaleler