Yamaha A-S500 El kitabı

Integrated Amplifier

Amplificateur Intégré

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

Printed in Malaysia ZC62540

Integrated Amplifier

Amplificateur Intégré

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press A to turn off this unit, and

then disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

A-S500 only

This label is required to be attached to a product of which the

temperature of the top cover may be hot during operation.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this

unit by

A or set it to the standby mode by A button on the remote

control. In this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 En

PREPARATIONINTRODUCTION

OPERATION

ADDITIONAL

INFORMATION

English

USEFUL FEATURES ............................................ 1

SUPPLIED ACCESSORIES ................................. 1

CONTROLS AND FUNCTIONS ......................... 2

Front panel and Remote control ................................ 2

About the remote control........................................... 3

Rear panel.................................................................. 4

CONNECTIONS .................................................... 5

Connecting speakers and source components............ 5

Connecting the power cable....................................... 7

PLAYING AND RECORDING.............................8

Playing a source......................................................... 8

Adjusting the tonal quality ........................................ 8

Recording a source .................................................... 9

PLAYING BACK TUNES FROM

YOUR iPhone/iPod ...........................................10

Using a Universal Dock for iPod............................. 11

Using a Wireless System for iPod ........................... 12

TROUBLESHOOTING .......................................13

SPECIFICATIONS...............................................17

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases

when the button names differ between the main unit and the remote control, the names of the buttons on the remote

control are given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

INTRODUCTION

This unit allows you to:

◆ Improve sound quality by using the Pure Direct (p. 8)

function

◆ Play back music from your iPhone/iPod (optional Yamaha

product required; p. 10)

◆ Select the recording source independently of the listening

source (A-S500 only; p. 9)

◆ Control other Yamaha components using this unit’s

remote control (p. 3)

◆ Boost bass sounds by connecting a subwoofer (p. 5)

◆ Save power by using POWER MANAGEMENT switch

(p. 7)

Please check that you received all of the following parts:

CONTENTS

INTRODUCTION

PREPARATION

OPERATION

ADDITIONAL INFORMATION

USEFUL FEATURES

SUPPLIED ACCESSORIES

Remote control Batteries (× 2)

(AA, R6, UM-3)

2 En

1 A (POWER)

Front panel: A switch

Turns on and off the power of this unit.

On position: Pushed inward

Off position: Released outward

Remote control: A button

When this unit is turned on: turns this unit on or sets it to

standby mode.

This unit consumes a small amount of power even when turned

off or when in standby mode.

2 POWER on indicator

Lights up as follows:

Brightly lit: Power is on

Dimly lit: Standby mode

Off: Power is off

y

The POWER on indicator remains brightly lit while an iPhone/

iPod is being charged, even if this unit is in standby mode.

3 Infrared signal transmitter

Sends signals to the main unit.

4 Remote control sensor

Receives signals from the remote control.

5 INPUT selector and indicators

Select the input source you want to listen to. The input

source indicators light up when the corresponding input

sources are selected.

y

The input source names correspond to the names of the

connection jacks on the rear panel.

CONTROLS AND FUNCTIONS

Front panel and Remote control

(A-S500)

Note

CONTROLS AND FUNCTIONS

3 En

INTRODUCTION

English

6 PHONES jack

Connect headphones for private listening. If you do not

want sound to be heard from the speakers, set the

SPEAKERS selector to OFF.

7 SPEAKERS selector

Turn on or off the speaker set connected to the

SPEAKERS A and/or B terminals on the rear panel each

time the corresponding SPEAKERS selector is set to A, B

or A+B.

8 REC OUT selector (A-S500 only)

Select a source for recording independently of the INPUT

selector setting, allowing you to record the selected source

while listening to another source (see page 9).

9 BASS control

Increases or decreases the low frequency response (see

page 9).

0 TREBLE control

Increases or decreases the high frequency response (see

page 9).

A BALANCE control

Adjusts the sound output balance of the left and right

speakers (see page 9).

B LOUDNESS control

Retains a full tonal range at any volume level (see page 9).

C PURE DIRECT switch and indicator

Reproduces any input source in the purest sound possible.

The indicator above it lights up when this function is

turned on (see page 8).

D VOLUME control

VOLUME +/–

Control the sound output level.

This does not affect the REC level for recording.

MUTE button (Remote control only)

Decreases the current volume by about 20 dB.

y

• The INPUT indicator for the current input source blinks while

the output is muted.

• The mute is released when MUTE button is pressed again, or

when the volume is adjusted by rotating the VOLUME control

on the front panel or by pressing the VOLUME +/– buttons on

the remote control.

E iPhone/iPod control buttons

Control an iPhone/iPod that is connected using an optional

Yamaha Universal Dock for iPod (see page 11) or

Wireless System for iPod (see page 12).

F Yamaha tuner control buttons

Control various functions of a Yamaha tuner.

Even when using a Yamaha tuner, certain components and

features may not be available. Refer to your component’s owner’s

manual for more information.

G Yamaha CD player control buttons

Control various functions of a Yamaha CD player.

Even when using a Yamaha CD player, certain components and

features may not be available. Refer to your component’s owner’s

manual for more information.

■ Installing batteries in the remote control

Make sure that the polarities are correct. See the illustration

inside the battery compartment.

■ Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of this unit during

operation.

The area between the remote control and this unit must be clear of

large obstacles.

Note

About the remote control

Note

AA, R6, UM-3 batteries

Note

Within 6m

(20 ft)

CONTROLS AND FUNCTIONS

4 En

1 CD input jacks

Used to connect a CD player (see page 5).

2 PHONO jacks and GND terminal

Used to connect a turntable that uses an MM cartridge,

and to ground the terminal (see page 5).

3 Audio input/output jacks

Used to connect external components, such as a tuner, etc

(see page 5).

4 DOCK jack

Used to connect an optional Yamaha Universal Dock for

iPod or Wireless System for iPod (see page 10).

5 SUBWOOFER OUT jack

Used to connect a subwoofer with built-in amplifier (see

page 5).

y

The SUBWOOFER OUT jack attenuates signals over 90 Hz.

6 POWER MANAGEMENT switch

Enables or disables the automatic power down function

(see page 7).

7 SPEAKERS A/B terminals

Used to connect one or two speaker sets (see page 5).

8 VOLTAGE SELECTOR switch

(Taiwan and Central/South America models

only)

The VOLTAGE SELECTOR switch must be set to your

local main voltage before plugging the power cable into

the wall outlet (see page 7).

9 IMPEDANCE SELECTOR switch

See IMPEDANCE SELECTOR switch on this page.

0 Power cable

Connect the power cable into the wall outlet (see page 7).

■ IMPEDANCE SELECTOR switch

Do not change the IMPEDANCE SELECTOR switch

while the power of this unit is turned on, as doing so may

damage the unit.

If the unit fails to turn on, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If this is the

case, remove the power cable and slide the switch all the

way to either position.

Select the switch position (LOW or HIGH) according to

the impedance of the speakers in your system.

Rear panel

(Taiwan and Central/South America models)

CAUTION

Switch

position

Impedance level

HIGH

• If you use one set (A or B), the impedance of

each speaker must be 6

Ω or higher.

• If you use two sets (A and B) simultaneously,

the impedance of each speaker must be 12

Ω

or higher.

• If you make bi-wire connections, the

impedance of each speaker must be 6

Ω or

higher. See page 6 for details.

LOW

• If you use one set (A or B), the impedance of

each speaker must be 4

Ω or higher.

• If you use two sets (A and B) simultaneously,

the impedance of each speaker must be 8

Ω or

higher.

• If you make bi-wire connections, the

impedance of each speaker must be 4

Ω or

higher. See page 6 for details.

5 En

PREPARATION

English

PREPARATION

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Use RCA cables for audio components (except for speaker connections and DOCK jack connections).

y

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

CONNECTIONS

Connecting speakers and source components

CAUTION

Turntable

Tuner SubwooferCD player

DVD player,

etc.

Tape deck, etc.

GND

Speakers A

Speakers B

Audio

out

Audio

out

Audio

out

Audio

in

CD recorder,

etc.

DOCK jack

connections

(see page 10)

Audio

out

Audio

out

Audio

out

Audio

in

6 En

CONNECTIONS

• The IMPEDANCE SELECTOR switch must be set to the appropriate position before connecting speaker sets. See

page 4 for details.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the

speakers.

• Do not connect this unit or other components to the main power until all connections between components are

complete.

1 Remove approximately 10 mm (3/8 in) of

insulation from the end of each speaker

cable and twist the exposed wires of the

cable together to prevent short circuits.

2 Connect the speaker cable.

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

■ Connecting via banana plug

(Except for Asia, U.K. and Europe

models)

Tighten the knob and then insert the banana plug into the

end of the corresponding terminal.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of

terminals and the low frequency driver to another set of

terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, set the IMPEDANCE

SELECTOR switch to HIGH or LOW depending on the

impedance of your speakers:

6 Ω or higher: HIGH

4 Ω or higher: LOW

See page 4 for more information about the IMPEDANCE

SELECTOR switch.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker.

y

To use the bi-wire connections, switch the SPEAKERS selector

to the A+B position.

CAUTION

10 mm (3/8 in)

Red: positive (+)

Black: negative (–)

Banana plug

CAUTION

Note

This unit

Speaker

7 En

CONNECTIONS

PREPARATION

English

■ POWER MANAGEMENT switch

Enables or disables the automatic power down function.

When the automatic power down function is enabled, this

unit will automatically switch to standby mode if no

operations are performed for 8 hours.

■ VOLTAGE SELECTOR switch

(Taiwan and Central/South America

models only)

The VOLTAGE SELECTOR switch on the rear panel of

this unit must be set for your local main voltage BEFORE

plugging the power cable into the wall outlet.

Improper setting of the VOLTAGE SELECTOR switch

may cause damage to this unit and create a potential fire

hazard.

Select the switch position (left or right) according to your

local voltage using a straight slot screwdriver. Voltages

are AC 110-120/220-240 V, 50/60 Hz.

■ Connecting the power cable

Plug the power cable into the wall outlet after all other

connections are complete.

Connecting the power cable

To the wall outlet with

the power cable

VOLTAGE

SELECTOR

POWER

MANAGEMENT

(Taiwan and Central/South America models)

8 En

OPERATION

1 Rotate the VOLUME control on the front

panel to the extreme counterclockwise

position.

2 Press A switch on the front panel inward to

turn on this unit.

3 Rotate the INPUT selector on the front panel

(or press one of the INPUT selector buttons

on the remote control) to select the input

source you want to listen to.

The indicator for the selected input source lights up.

4 Rotate the SPEAKERS selector on the front

panel to select SPEAKERS A, B or A+B.

• Set the SPEAKERS selector to the A+B position when two sets

of speakers are connected using bi-wire connections, or when

using two sets of speakers simultaneously (A and B).

• If you do not want sound to be heard from the speakers while

listening with headphones, set the SPEAKERS selector to OFF.

5 Play the selected input source.

6 Rotate the VOLUME control on the front

panel (or press VOLUME +/– buttons on the

remote control) to adjust the sound output

level.

y

You can adjust the tonal quality by using the BASS, TREBLE,

BALANCE and LOUDNESS controls, or the PURE DIRECT

switch on the front panel.

7 When finished listening, press A switch on

the front panel outward to turn off this unit.

y

If A button on the remote control is pressed while the A switch on

the front panel is in the on position, this unit enters standby mode.

Press A button again to turn this unit on.

■ Using the PURE DIRECT switch

Routes input signals from your audio sources. As a result,

the input signals bypass the BASS, TREBLE, BALANCE

and LOUDNESS controls, thus eliminating any alterations

to the audio signals to produce more direct and high-grade

sound from all input sources.

The BASS, TREBLE, BALANCE and LOUDNESS controls do

not function while the PURE DIRECT switch is turned on.

PLAYING AND RECORDING

Playing a source

Notes

SPEAKERS VOLUME

INPUTA

INPUT

VOLUME

Adjusting the tonal quality

Note

VOLUMELOUDNESSTREBLE

BASS BALANCE PURE

DIRECT

9 En

PLAYING AND RECORDING

OPERATION

English

■ Adjusting the BASS and TREBLE

controls

The BASS and TREBLE controls adjust high and low

frequency response.

The center position produces a flat response.

BASS

When you feel there is not enough bass (low frequency

sound), rotate clockwise to boost. When you feel there is

too much bass, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 Hz)

TREBLE

When you feel there is not enough treble (high frequency

sound), rotate clockwise to boost. When you feel there is

too much treble, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 kHz)

■ Adjusting the BALANCE control

The BALANCE control adjusts the sound output balance

of the left and right speakers to compensate for sound

imbalance caused by speaker locations or listening room

conditions.

■ Adjusting the LOUDNESS control

Retain a full tonal range at any volume level, thus

compensating for the human ears’ loss of sensitivity to

high and low-frequency ranges at low volume.

If the PURE DIRECT switch is turned on with the

LOUDNESS control set at a certain level, the input signals

bypass the LOUDNESS control, resulting in a sudden

increase in the sound output level. To prevent your ears or

the speakers from being damaged, be sure to press PURE

DIRECT switch AFTER lowering the sound output level

or AFTER checking that the LOUDNESS control is

properly set.

1 Set the LOUDNESS control to the FLAT

position.

2 Rotate the VOLUME control on the front

panel (or press VOLUME +/– buttons on the

remote control) to set the sound output level

to the loudest listening level that you would

listen to.

3 Rotate the LOUDNESS control until the

desired volume is obtained.

y

After setting the LOUDNESS control, enjoy listening to music at

your preferred volume level. If the effect of the LOUDNESS

control setting is too strong or weak, readjust the LOUDNESS

control.

• For the A-S500, audio signals are not output via the LINE 2

REC or LINE 3 REC output jacks when LINE 2 or LINE 3 is

selected with the REC OUT selector.

• For the A-S300, audio signals are not output via the LINE 2

REC or LINE 3 REC output jacks when LINE 2 or LINE 3 is

selected with the INPUT selector.

• This unit must be turned on in order to record.

• The VOLUME, BASS, TREBLE, BALANCE and

LOUDNESS controls and the PURE DIRECT switch have no

effect on the source being recorded.

• Check the copyright laws in your country before recording from

records, CDs, radio, etc. Recording copyright-protected

material may infringe on copyright laws.

1 Rotate the REC OUT selector on the front

panel to select the source you want to record

(A-S500 only).

When using the A-S300, the current input source will be

recorded.

2 Play the source and begin recording using

the recording device connected to the REC

output jacks (LINE 2 and/or LINE 3) on the

rear panel. See page 5.

y

A-S500 only: While recording, you can select another input

source using the INPUT selector or the remote control and listen

to another input source without affecting recording.

CAUTION

Recording a source

Notes

Note

REC OUT

(A-S500 only)

10 En

Once you have connected an optional Yamaha Universal Dock for iPod or Wireless System for iPod to the DOCK jack

on the rear panel of this unit, you can enjoy playback of your iPhone/iPod using the remote control supplied with this

unit.

To prevent accidents, unplug the power cable of this unit before connecting a Universal Dock for iPod or a Wireless

System for iPod.

If the iPhone connected to the YID-W10 receives a call while this unit is in standby mode, the unit turns on automatically and the

ringtone is heard through this unit. If you do not want this unit to turn on when a call is received, set the iPhone to silent mode.

PLAYING BACK TUNES FROM YOUR iPhone/iPod

Universal Dock for iPod Wireless System for iPod

Model

(As of July 2010)

• YDS-12

• YDS-11

• YDS-10

YID-W10

Operated by

• Remote control

• iPhone/iPod connected to the dock

• iPhone/iPod connected to the YID-W10

transmitter

• Remote control

Supported iPhone/iPod

(As of July 2010)

• iPod touch

• iPod (4th Gen/5th Gen/classic)

• iPod nano

•iPod mini

•iPhone

•iPhone 3G/3GS

• iPod touch

• iPod (5th Gen/classic)

• iPod nano

• iPhone

• iPhone 3G/3GS

Remarks

• iPhone/iPod charging also supported.

• The YDS-10/YDS-11 does not support iPhone

connection.

iPhone/iPod charging also supported.

CAUTION

Note

Universal Dock for iPod Wireless System for iPod

Position the connected device

as far as possible from the unit.

11 En

PLAYING BACK TUNES FROM YOUR iPhone/iPod

OPERATION

English

After setting your iPhone/iPod in your dock, rotate the

INPUT selector on the front panel (or press DOCK button

on the remote control) to select DOCK as the input source

to play your iPhone/iPod.

While viewing the information displayed on your iPhone/

iPod, use the following remote control buttons to operate

(playback, pause, skip, etc.) your iPhone/iPod.

Some shuffle modes and repeat modes may not be available

depending on the model or the software version of your iPhone/

iPod.

y

When this unit is turned on or is in standby mode, your iPhone/

iPod can be charged automatically if it is connected to a

Universal Dock for iPod. If an iPhone/iPod is charged while this

unit is in standby mode, the POWER on indicator lights up

brightly.

Using a Universal Dock for iPod

Remote

control

Operation

MENU

Displays the menu.

ENTER

• If an item is selected: Confirms the item and

displays the next screen.

• If a song is selected: Plays the selected song.

B

Scroll up.

C

Scroll down.

Ee

• If a song is playing: Pauses the song.

• If a song is paused: Plays the song.

a

• If a song is playing or paused: Skips to the

beginning of the next song.

• If pressed and held: Searches forward.

b

• If a song is playing or paused: Skips to the

beginning of the current song.

• Pressing repeatedly skips one song backwards with

each press.

• If pressed and held: Searches backward.

Switches between shuffle modes (Off → Songs →

Albums → Off).

Switches between repeat modes (Off → One → All

→ Off).

Front panel Remote control

or

iPhone/iPod

control

Note

12 En

PLAYING BACK TUNES FROM YOUR iPhone/iPod

■ Establishing a wireless connection

Once the iPhone/iPod is connected to the transmitter and

playback begins, it takes about 5 seconds for audio to be

heard. During this time the wireless connection between

the transmitter and receiver is established.

The status of the wireless connection between the transmitter

and receiver is indicated by the respective status indicator.

■ Controlling this unit with your iPhone/

iPod

• When playback begins on an iPhone/iPod that is

connected to a transmitter, and if the transmitter is

within range of the receiver, this unit performs as

follows:

– If this unit is already turned on when playback

begins: The input source switches to DOCK.

– If this unit is in standby mode when playback

begins: This unit turns on and the input source

switches to DOCK.

• Adjusting the volume on the iPhone/iPod also adjusts

the volume of this unit. Note that the iPhone/iPod can

only be used to increase this unit’s volume to a certain

level; to increase it further, adjust the volume using this

unit’s VOLUME control or the remote control.

• In the following situations, the wireless connection

between the transmitter and receiver is disconnected.

After 30 seconds this unit automatically enters standby

mode.

– The iPhone/iPod is not operated for about 30-120

seconds after the playback is paused.

– The sleep timer of the iPhone/iPod is activated.

– The iPhone/iPod is disconnected from the

transmitter.

– The iPhone/iPod battery level decreases to a level

where it cannot provide enough power to the

transmitter.

– The transmitter is moved outside of the wireless

communication range of the receiver.

– Communication between the transmitter and

receiver becomes disrupted due to interference from

other wireless LAN devices, cordless telephones,

microwave ovens, etc.

y

• You can use the remote control to control the iPhone/iPod. For

more information, see page 11.

• When this unit is turned on or is in standby mode, your iPhone/

iPod can be charged automatically if the transmitter connected

to your iPhone/iPod is stationed to the receiver. If an iPhone/

iPod is charged while this unit is in standby mode, the POWER

on indicator lights up brightly.

• Refer to the operating instructions of the YID-W10 for more

information.

Using a Wireless System for iPod

Status of

connection

Transmitter

indicator

Receiver

indicator

No connection Off Off

Confirming connection Green, flashing Blue, flashing

Connected Green, lit Blue, lit

YID-W10 receiver

YID-W10 transmitter

13 En

ADDITIONAL

INFORMATION

English

ADDITIONAL INFORMATION

Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or

if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized

Yamaha dealer or service center.

■ General

TROUBLESHOOTING

Problems Possible Causes Solutions

Refer to

page

This unit is not turned

on. The POWER on

indicator also does

not light up.

The power cable is not connected. Connect the power cable firmly. 7

The A button is pressed on the remote

control while this unit is turned off.

Press A switch on the front panel to ON.

2

There is a problem with the internal

circuitries of this unit.

Disconnect the power cable and contact the nearest

authorized Yamaha dealer or service center. If an

unusual odor or noise is generated from the unit, do

not turn on the power, disconnect the power cable,

and contact a service center for repair.

—

This unit turns off

suddenly and the

POWER on indicator

blinks.

This unit is turned off

after several seconds

of turning on, and the

POWER on indicator

blinks.

The speaker wires are touching each other

or shorting out against the rear panel.

Connect the speaker cables properly and press the A

switch again. The INPUT indicators blink and the

volume is decreased automatically. After the volume

has decreased to the lowest setting, the INPUT

indicators stop flashing, the INPUT indicator of the

last input source selected lights up, and the unit may

be used again. Confirm normal sound output from

speakers by increasing the volume gradually, then

operate this unit normally.

6

The speaker is malfunctioning. Replace the speaker set and press the A switch again.

The INPUT indicators blink and the volume is

decreased automatically. After the volume has

decreased to the lowest setting, the INPUT indicators

stop flashing, the INPUT indicator of the last input

source selected lights up, and the unit may be used

again. Confirm normal sound output from speakers

by increasing the volume gradually, then operate this

unit normally.

—

The protection circuitry has been activated

because of excessive input or excessive

volume level.

Rotate the VOLUME control on the front panel to

decrease the volume level and then turn the power on

again.

—

The protection circuitry has been activated

due to excessive internal temperature.

Allow about 30 minutes for the temperature inside

this unit to decrease, rotate the VOLUME control on

the front panel to lower the volume and then turn the

power on again. Set the unit in a place where heat can

readily dissipate from the unit.

—

The IMPEDANCE SELECTOR switch is

not fully slid to either position.

Turn the power off and slide the IMPEDANCE

SELECTOR switch all the way to the correct

position.

4

The IMPEDANCE SELECTOR switch is

not set to the correct position.

Set the IMPEDANCE SELECTOR switch to the

position that corresponds to the impedance of your

speakers.

4

This unit has been exposed to a strong

external electric shock (such as lightning

or strong static electricity).

Set this unit to standby mode, disconnect the power

cable, plug it back in after 30 seconds, then use the

unit normally.

—

There is a problem with the internal

circuitries of this unit.

Disconnect the power cable and contact the nearest

authorized Yamaha dealer or service center. If an

unusual odor or noise is generated from the unit, do

not turn on the power, disconnect the power cable,

and contact a service center for repair.

—

14 En

TROUBLESHOOTING

No sound. Sound is muted. Press MUTE button on the remote control or rotate

the VOLUME control.

3

Incorrect cable connections. Connect the stereo cable for audio units and the

speaker wires properly. If the problem persists, the

cables may be defective.

5

Playback has been stopped on the

connected component.

Turn the component on and start playback.

8

No appropriate input source has been

selected.

Select an appropriate input source with the INPUT

selector on the front panel (or one of the INPUT

selector buttons on the remote control).

8

The SPEAKERS selector is not set

properly.

Set the corresponding SPEAKERS selector to A, B or

A+B position.

8

The sound suddenly

goes off.

The protection circuitry has been activated

because of a short circuit, etc.

Check that the IMPEDANCE SELECTOR setting is

correct.

4

Check that the speaker wires are not touching each

other or shorting out against the rear panel of this

unit, and then turn this unit on again.

5

This unit has become too hot. Reconsider the location where this unit is installed.

Make sure the openings on the top panel are not

blocked.

—

The automatic power down function has

turned this unit off.

Confirm that there are no other issues causing this

problem, and then turn this unit on again.

7

Only the speaker on

one side can be

heard.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

5

Incorrect setting for the BALANCE

control.

Set the BALANCE control to the appropriate

position.

9

There is a lack of

bass and no

ambience.

The + and – wires are connected in

reverse at the amplifier or the speakers.

Connect the speaker wires to the correct + and –

phase. 6

A “humming” sound

can be heard.

Incorrect cable connections. Connect the audio plugs firmly. If the problem

persists, the cables may be defective.

5

No connection from the turntable to the

GND terminal.

Make the GND connection between the turntable and

this unit.

5

The volume level is

low while playing a

record.

The turntable is connected to the jacks

other than the PHONO jacks.

Connect the turntable to the PHONO jacks.

5

The record is being played on a turntable

with an MC cartridge.

Use a turntable equipped with an MM cartridge.

—

The volume level

cannot be increased,

or the sound is

distorted.

The component connected to the LINE 2

REC or LINE 3 REC jacks of this unit is

turned off.

Turn on the power of the component.

—

The sound is

degraded when

listening with the

headphones

connected to the CD

player or the tape

deck connected to

this unit.

This unit is turned off or is in standby

mode.

Turn this unit on.

8

The sound level is

low.

Sound is muted. Press MUTE button on the remote control or rotate

the VOLUME control.

3

The loudness control function is

operating.

Turn down the volume, set the LOUDNESS control

to the FLAT position, and then adjust the volume

again.

9

Problems Possible Causes Solutions

Refer to

page

15 En

TROUBLESHOOTING

ADDITIONAL

INFORMATION

English

■ Universal Dock for iPod and Wireless System for iPod

Using the BASS,

TREBLE, BALANCE

and LOUDNESS

controls does not

affect the tonal quality.

The PURE DIRECT switch is turned on. The PURE DIRECT switch must be turned off to use

those controls.

8

Problems Possible Causes Solutions

Refer to

page

No sound.

You cannot operate

the iPhone/iPod.

There is a problem with the signal path

from your iPhone/iPod to the unit.

Turn off the unit and reconnect the Universal Dock

for iPod or the Wireless System for iPod to the

DOCK jack of the unit.

10

Remove your iPhone/iPod from the Universal Dock

for iPod or the Wireless System for iPod and then

place it back in the dock.

10

The iPhone/iPod being used is not

supported by the unit.

Connect an iPhone/iPod supported by the unit.

10

When using a

Wireless System for

iPod:

Sound frequently cuts

out.

Noise is heard.

The wireless connection is poor. Place the YID-W10 receiver as far away from this

unit as possible.

10

When using the

Universal Dock for

iPod:

Your iPhone/iPod is

not being charged

even though it is

connected to the

Universal Dock for

iPod.

This unit is not turned on. Turn on this unit or set it to standby mode. 2

The iPhone/iPod is not connected

securely.

Connect the iPhone/iPod securely to the Universal

Dock for iPod.

10

When using the

Wireless System for

iPod:

Your iPhone/iPod is

not being charged

even though the YID-

W10 transmitter

connected to your

iPhone/iPod is

stationed in the YID-

W10 receiver.

This unit is not turned on. Turn on this unit or set it to standby mode. 2

The YID-W10 transmitter is not stationed

securely in the YID-W10 receiver.

Station the YID-W10 transmitter connected to your

iPhone/iPod securely in the YID-W10 receiver.

10

Problems Possible Causes Solutions

Refer to

page

16 En

TROUBLESHOOTING

■ Remote control

■ Notes on batteries

• Change both batteries when the operation range of the

remote control decreases.

• Remove the batteries if the remote control is not to be

used for an extended period of time.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean the

battery compartment thoroughly before installing new

batteries.

• Do not throw away batteries with general house waste;

dispose of them correctly in accordance with your local

regulations.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity, such as near a bath

– high temperature, such as near a heater or a stove

– extremely low temperatures

– dusty places

• Do not expose the remote control sensor to strong

lighting, in particular, an inverter type fluorescent

lamp; otherwise, the remote control may not work

properly. If necessary, position the unit away from

direct lighting.

Problems Possible Causes Solutions

Refer to

page

The remote control

does not work nor

function properly.

The remote control is too far away or

tilted too much.

The remote control will function within a maximum

range of 6 m (20 ft) and no more than 30 degrees off-

axis from the front panel.

3

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

Reposition this unit or lighting.

—

The batteries are weak. Replace all batteries. 3

17 En

ADDITIONAL

INFORMATION

English

AUDIO SECTION

• Minimum RMS output power

(8 Ω, 20 Hz to 20 kHz, 0.019% THD)

[A-S500] ................................................................ 85 W + 85 W

[A-S300] ................................................................ 60 W + 60 W

(6 Ω, 20 Hz to 20 kHz, 0.038% THD) [Except for Asia model]

[A-S500] ............................................................ 100 W + 100 W

[A-S300] ................................................................ 70 W + 70 W

• Dynamic power per channel (IHF) (8/6/4/2 Ω)

[A-S500] ......................................................... 130/150/185/220 W

[A-S300] ......................................................... 100/120/140/150 W

• Maximum power per channel [U.K. and Europe models only]

(1 kHz, 0.7% THD, 4 Ω)

[A-S500] ............................................................................120 W

[A-S300] ............................................................................. 95 W

• IEC power [U.K. and Europe models only]

(1 kHz, 0.019% THD, 8 Ω)

[A-S500] ........................................................................... 100 W

[A-S300] ............................................................................. 75 W

• Power band width

[A-S500] (0.06% THD, 42.5 W, 8 Ω) ................. 10 Hz to 50 kHz

[A-S300] (0.06% THD, 30 W, 8 Ω).................... 10 Hz to 50 kHz

• Damping factor (SPEAKERS A)

1 kHz, 8 Ω................................................................... 240 or more

• Maximum effective output power (JEITA)

(1kHz, 10% THD, 8 Ω) [Asia, China, Taiwan and Central/South

America models only]

[A-S500] ........................................................................... 130 W

[A-S300] ........................................................................... 100 W

(1kHz, 10% THD, 6 Ω) [China, Taiwan and Central/South

America models only]

[A-S500] ........................................................................... 150 W

[A-S300] ........................................................................... 110 W

• Input sensitivity/Input impedance

PHONO (MM)........................................................ 3.0 mV/47 kΩ

CD, etc. .................................................................. 200 mV/47 kΩ

• Maximum input signal

PHONO (MM) (1 kHz, 0.003% THD).................. 60 mV or more

CD, etc. (1 kHz, 0.5% THD) ................................... 2.2 V or more

• Output level/Output impedance

REC............................................................ 200 mV/1.0 kΩ or less

• PHONES jack rated output/Impedance

CD, etc. (Input 1 kHz, 200 mV, 8 Ω)

[A-S500] ............................................................. 430 mV/470 Ω

[A-S300] ............................................................. 360 mV/470 Ω

• Frequency response

CD, etc. (20 Hz to 20 kHz)............................................ 0 ± 0.5 dB

CD, etc. PURE DIRECT on (10 Hz to 100 kHz) .......... 0 ± 1.0 dB

• RIAA equalization deviation

PHONO (MM).................................................................. ± 0.5 dB

• Total harmonic distortion

PHONO (MM) to REC (20 Hz to 20 kHz, 3 V)..... 0.025% or less

CD, etc. to SPEAKERS

[A-S500] (20 Hz to 20 kHz, 42.5 W, 8 Ω) .......... 0.015% or less

[A-S300] (20 Hz to 20 kHz, 30 W, 8 Ω) ............. 0.015% or less

• Signal to noise ratio (IHF-A network)

PHONO (MM) (5 mV input shorted) ..................... 85 dB or more

CD, etc. PURE DIRECT on

(200 mV input shorted)...................................... 100 dB or more

• Residual noise (IHF-A network) ............................................ 30 µV

• Channel separation

CD, etc. (5.1 kΩ input shorted, 1/10 kHz) ......... 65/50 dB or more

• Tone control characteristics

BASS

Boost/Cut (50 Hz) ........................................................... ±10 dB

Turnover frequency.......................................................... 350 Hz

TREBLE

Boost/Cut (20 kHz) ......................................................... ±10 dB

Turnover frequency......................................................... 3.5 kHz

• Continuous loudness control

Attenuation (1 kHz)............................................................. –30 dB

• Gain tracking error (0 to –99 dB)................................ 0.5 dB or less

GENERAL

• Power supply

[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz

[Asia model]........................................... AC 220-240 V, 50/60 Hz

[Taiwan and Central/South America models]

.............................................. AC 110-120/220-240 V, 50/60 Hz

[China model]..................................................... AC 220 V, 50 Hz

[Australia model] .............................................. AC 240 V, 50 Hz

[U.K., Europe and Russia models] .................... AC 230 V, 50 Hz

• Power consumption

[A-S500]

[U.S.A. and Canada models].............................. 240 W, 330 VA

[Asia model]..................................................................... 220 W

[Other models]. ................................................................ 240 W

[A-S300].............................................................................. 190 W

• Standby power consumption ....................................... 0.5 W or less

• YID-W10 standby power consumption

(YID-W10 connect) ..................................................... 1.2 W or less

• iPod charge power consumption

[A-S500]..................................................................... 35 W or less

[A-S300]..................................................................... 25 W or less

• Maximum power consumption [Taiwan and Central/South America

models only]

(6 Ω, 1 kHz, 10% THD)

[A-S500]........................................................................... 510 W

[A-S300]........................................................................... 400 W

• Dimensions (W × H × D) ............................... 435 × 151 × 387 mm

(17-1/8" × 6" × 15-1/4")

•Weight

[A-S500]............................................................. 10.3 kg (22.7 lbs)

[A-S300]............................................................... 9.0 kg (19.8 lbs)

Specifications are subject to change without notice.

iPhone, iPod

iPhone, iPod, iPod classic, iPod nano and iPod touch are

trademarks of Apple Inc., registered in the U.S. and other

countries.

SPECIFICATIONS

i Fr

1 Pour utiliser l’appareil au mieux de ses possibilités, lisez

attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

2 Installez cet ensemble audio dans un endroit bien aéré,

frais, sec et propre - veillez à ce qu’il soit à l’abri de la

lumière directe du soleil, des sources de chaleur, des

vibrations, des poussières, de l’humidité et/ou du froid.

Pour une ventilation correcte, ménagez l’espace

minimum suivant autour de cet appareil.

Au-dessus : 30 cm

À l’arrière : 20 cm

Sur les côtés : 20 cm

3 Placez l’appareil loin des équipements, moteurs et

transformateurs électriques, pour éviter les ronflements

parasites.

4 N’exposez pas l’appareil à des variations brutales de

température, ne le placez pas dans un environnement très

humide (par exemple dans une pièce contenant un

humidificateur) car cela peut entraîner la condensation

d’humidité à l’intérieur de l’appareil qui elle-même peut

être responsable de décharge électrique, d’incendie, de

dommage à l’appareil ou de blessure corporelle.

5 Evitez d’installer l’appareil dans un endroit où des objets

peuvent tomber, ainsi que là où l’appareil pourrait être

exposé à des éclaboussures ou des gouttes d’eau. Sur le

dessus de l’appareil, ne placez pas :

– d’autres appareils qui peuvent endommager la surface

de l’appareil ou provoquer sa décoloration.

– des objets se consumant (par exemple, une bougie)

qui peuvent être responsables d’incendie, de

dommage à l’appareil ou de blessure corporelle.

– des récipients contenant des liquides qui peuvent être

à l’origine de décharge électrique ou de dommage à

l’appareil.

6 Ne couvrez pas l’appareil d’un journal, d’une nappe, d’un

rideau, etc. car cela empêcherait l’évacuation de la

chaleur. Toute augmentation de la température intérieure

de l’appareil peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle.

7 Ne branchez pas la fiche du câble d’alimentation de

l’appareil sur une prise secteur aussi longtemps que tous

les raccordements n’ont pas été effectués.

8 Ne pas faire fonctionner l’appareil à l’envers. Il risquerait

de chauffer et d’être endommagé.

9 N’exercez aucune force excessive sur les commutateurs,

les boutons et les cordons.

10 Pour débrancher la fiche du câble d’alimentation au

niveau de la prise secteur, saisissez la fiche et ne tirez pas

sur le cordon.

11 Ne nettoyez pas l’appareil au moyen d’un solvant

chimique, ce qui pourrait endommager la finition.

Utilisez un chiffon sec et propre.

12 N’alimentez l’appareil qu’à partir de la tension prescrite.

Alimenter l’appareil sous une tension plus élevée est

dangereux et peut être responsable d’incendie, de

dommage à l’appareil ou de blessure corporelle. Yamaha

ne saurait être tenue responsable des dommages résultant

de l’alimentation de l’appareil sous une tension autre que

celle prescrite.

13 Pour empêcher tout dommage causé par les éclairs,

déconnectez le câble d’alimentation et toute antenne

extérieure de la prise murale pendant un orage.

14 Ne tentez pas de modifier ni de réparer l’appareil.

Consultez le service Yamaha compétent pour toute

réparation qui serait requise. Le coffret de l’appareil ne

doit jamais être ouvert, quelle que soit la raison.

15 Si vous envisagez de ne pas vous servir de l’appareil

pendant une longue période (par exemple, pendant les

vacances), débranchez la fiche du câble d’alimentation au

niveau de la prise secteur.

16 Lisez la section intitulée « GUIDE DE DÉPANNAGE »

où figurent une liste d’erreurs de manipulation

communes avant de conclure que l’appareil présente une

anomalie de fonctionnement.

17 Avant de déplacer l’appareil, appuyez sur A pour mettre

l’appareil hors tension, puis débranchez la fiche du

cordon d’alimentation au niveau de la prise secteur.

18 La condensation se forme lorsque la température

ambiante change brusquement. En ce cas, débranchez la

fiche du câble d’alimentation et laissez l’appareil reposer.

19 La température de l’appareil peut augmenter en raison

d’une utilisation prolongée. En ce cas, coupez

l’alimentation de l’appareil et laissez-le au repos pour

qu’il refroidisse.

20 Installez cet appareil à proximité de la prise secteur et à

un emplacement où la fiche du câble d’alimentation est

facilement accessible.

21 Les piles ne doivent pas être exposées à une chaleur

extrême, par exemple au soleil, à une flamme, etc. Lors

de la mise au rebut des piles, suivez vos réglementations

locales.

22 Une pression excessive du son par les écouteurs et le

casque d’écoute peut entraîner la perte de l’ouïe.

A-S500 uniquement

Cette étiquette doit être apposée sur un produit dont le capot

supérieur peut devenir chaud lorsqu’il fonctionne.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER

L’APPAREIL.

Aussi longtemps que cet appareil est raccordé à la prise secteur

murale, il n’est pas débranché de la source d’alimentation secteur

même si vous le mettez hors tension à l’aide de la touche A ou le

mettez en mode veille à l’aide de la touche A de la

télécommande. En mode veille, l’appareil consomme une très

faible quantité de courant.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET

APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

Sayfa yükleniyor ...

Yamaha A-S500 El kitabı

Bu kılavuz için de uygundur

Yamaha A-S500 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler