Yamaha R-S300 El kitabı

Kategori
Araba medya alıcıları
Tip
El kitabı
©
2010 Yamaha Corporation
Receiver
Ampli-Tuner
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
G
Printed in Malaysia WV17430-2
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
i En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances
around this unit.
Top: 30 cm (11-3/4 in)
Rear: 20 cm (7-7/8 in)
Sides: 20 cm (7-7/8 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press A to turn off this unit, and
then disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This label is required to be attached to a product of which
the temperature of the top cover may be hot during
operation.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this
unit by A or set it to the standby mode by A button on the remote
control. In this state, this unit is designed to consume a very small
quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
1 En
PREPARATIONINTRODUCTION
BASIC
OPERATION
ADDITIONAL
INFORMATION
ADVANCED
OPERATION
English
USEFUL FEATURES ............................................ 2
SUPPLIED ACCESSORIES ................................. 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel................................................................. 4
Front panel display .................................................... 6
Rear panel.................................................................. 7
Remote control........................................................... 8
Using the remote control ........................................... 9
CONNECTIONS .................................................. 10
Connecting speakers and source components.......... 10
Connecting the FM and AM antennas..................... 12
Connecting power cable .......................................... 12
PLAYING AND RECORDING .......................... 13
Playing a source....................................................... 13
Adjusting the tonal quality....................................... 14
Recording a source .................................................. 16
Using the sleep timer ............................................... 16
FM/AM TUNING ................................................. 17
Automatic tuning ..................................................... 17
Manual tuning.......................................................... 18
Automatic station preset (FM stations only) ........... 19
Manual station preset...............................................20
Recalling a preset station......................................... 21
Clearing a preset station........................................... 21
Clearing all preset stations....................................... 22
Receiving Radio Data System information
(FM stations only) ............................................... 23
TP Search function (FM stations only).................... 24
PLAYING BACK TUNES
FROM YOUR iPhone/iPod/
Bluetooth™ COMPONENT............................ 25
Using a Universal Dock for iPod............................. 26
Using a Wireless System for iPod ........................... 27
Using a Bluetooth Wireless Audio Receiver........... 28
SETTING THE OPTION MENU
FOR EACH INPUT SOURCE.........................30
Option menu items................................................... 30
ADVANCED SETUP ............................................32
Changing the ADVANCED SETUP
menu parameters.................................................. 32
TROUBLESHOOTING .......................................33
SPECIFICATIONS...............................................38
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
ADVANCED OPERATION
ADDITIONAL INFORMATION
USEFUL FEATURES
2 En
This unit allows you to:
*
Optional Yamaha product required
iPhone, iPod
iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other
countries.
Bluetooth™
Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the front panel of this unit or those on the remote controls. In case
the button names differ between this unit and the remote controls, the names of the buttons on the remote controls are given in
parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
USEFUL FEATURES
Improve sound quality by using the Pure Direct function
p. 14
Play back music from your iPhone/iPod
*
or Bluetooth component
*
p. 25
Listen to FM and AM radio stations
p. 17
Receive and display Radio Data System information
p. 23
Boost bass sounds by connecting a subwoofer
p. 10
Use this unit’s remote control to operate a Yamaha CD player
p. 8
Save power by using the automatic power down function
p. 32
INTRODUCTION
SUPPLIED ACCESSORIES
3 En
INTRODUCTION
English
Please check that you received all of the following parts.
Notes on remote control and batteries
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following conditions:
places of high humidity, such as near a bath
places of high temperatures, such as near a heater or stove
places of extremely low temperatures
dusty places
Use AA, R6, UM-3 batteries for the remote control.
Insert batteries according to the polarity markings (+ and -).
Change all batteries if you notice the operation range of the remote control narrows.
If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.
If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material
comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery
compartment thoroughly before installing new batteries.
Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.
Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a
different specification.
Before inserting new batteries, wipe the battery compartment clean.
Dispose of batteries according to your regional regulations.
SUPPLIED ACCESSORIES
Remote control
Indoor FM antenna
AM loop antenna
Batteries (x2)
(AA, R6, UM-3)
CONTROLS AND FUNCTIONS
4 En
1 A (power)
Turns on and off the power of this unit (see page 13).
On position: Pushed inward
Off position: Released outward
This unit consumes a small amount of power even when turned
off or when in standby mode.
2 Power indicator
Lights up as follows:
Brightly lit: Power is on
Dimly lit: Standby mode
Off: Power is off
If an iPhone/iPod is charged while this unit is in standby mode,
the power indicator lights up brightly.
3 SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel each time the corresponding button is pressed (see
page
13
).
4 TP
Searches automatically for a station that provides traffic
program (TP) broadcasts (see page 24).
5 INFO
Turns on and changes the Radio Data System display
mode when TUNER is selected as the input source (see
page 23).
Changes the playback information displayed about the
song playing on the iPhone/iPod when DOCK is selected
as the input source (see page 26).
Playback information can only be displayed for an iPhone/iPod
that is connected using a Universal Dock for iPod.
6 MEMORY
Stores the current FM/AM station as a preset when
TUNER is selected as the input source (see page 20).
7 CLEAR
Clears the current FM/AM preset station when TUNER is
selected as the input source (see page 21).
8 Front panel display
Shows information about the operational status of this
unit.
9 PRESET j / i
Selects a preset FM/AM station when TUNER is selected
as the input source (see page 21).
0 FM, AM
Sets the FM/AM tuner band to FM or AM when TUNER
is selected as the input source (see page 17).
CONTROLS AND FUNCTIONS
Front panel
Note
Note
Note
CONTROLS AND FUNCTIONS
5 En
INTRODUCTION
English
A TUNING jj / ii
Selects the tuning frequency when TUNER is selected as
the input source (see page 17).
B Remote control sensor
Receives infrared signals from the remote control.
C PURE DIRECT and indicator
Allows you to listen to a source in the purest possible
sound (see page 14). The indicator above it lights up and
the front panel display turns off when this function is
turned on.
D PHONES jack
Outputs audio to your headphones for private listening.
Press SPEAKER A/B so that the SP A/B indicators turn off
before you connect your headphones to the PHONES jack.
E BASS control
Increases or decreases the low frequency response. The
center position produces a flat response (see page 14).
F TREBLE control
Increases or decreases the high frequency response. The
center position produces a flat response (see page 14).
G BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances caused by
speaker locations or listening room conditions (see page
14).
H LOUDNESS control
Retains a full tonal range at any volume level to
compensate for the human ears’ loss of sensitivity to high
and low-frequency ranges at a low volume level (see page
15).
I INPUT selector
Selects the input source you want to listen to.
J VOLUME control
Increases or decreases the sound output level.
This does not affect the output level of the REC jacks.
Note
Note
CONTROLS AND FUNCTIONS
6 En
1 SP (SPEAKERS) A/B indicators
Light up according to the set of speakers selected.
Both indicators light up when both sets of speakers are
selected.
2 Input source indicators
Light up brightly to indicate the input source that is
currently selected.
3 PRESET indicator
Lights up when you recall a preset radio station. Blinks
while the automatic station preset feature is scanning for
FM stations to register as presets.
4 MEMORY indicator
Lights up or blinks when an FM/AM station is being
stored as a preset.
5 TUNED indicator
Lights up when this unit is tuned in to an FM or AM
station.
6 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast.
7 TP indicator
Lights up when this unit is tuned in to a Traffic Program
(TP) station. Blinks when searching for a TP station.
8 SLEEP indicator
Lights up when the sleep timer is turned on.
9 MUTE indicator
Blinks while the MUTE function is turned on.
0 P indicator
Lights up when a preset number is selected. Blinks while
you are registering a preset radio station.
A Multi-information display
Shows information when adjusting or changing settings.
B Volume indicator
Displays the current volume level.
Front panel display
CONTROLS AND FUNCTIONS
7 En
INTRODUCTION
CONTROLS AND FUNCTIONS
English
Rear panel
1 GND terminal
Used to connect a turntable (see page 10).
2 TAPE jacks
Used to connect a tape deck (see page 10).
3 Antenna terminals
Used to connect FM and AM antennas (see page 12).
4 DOCK jack
Used to connect an optional Yamaha Universal Dock for
iPod (such as the YDS-12), Wireless System for iPod
(YID-W10), or Bluetooth Wireless Audio Receiver
(YBA-10) (see page 25).
5 Power cable
For connecting this unit to an AC wall outlet (see page
12).
6 PHONO jacks
Used to connect a turntable (see page 10).
7 CD jacks
Used to connect a CD player (see page 10).
8 LINE 1-2 jacks
Used to connect audio components (see page 10).
9 SUBWOOFER OUT jack
Used to connect a subwoofer with built-in amplifier (see
page 10).
y
The SUBWOOFER OUT jack attenuates signals over 90 Hz.
0 POWER MANAGEMENT switch
Used to enable or disable the automatic power down
function. When this function is enabled, this unit
automatically enters standby mode if it is not operated for
a certain amount of time (3 settings are available; see page
32).
A SPEAKERS terminals
Used to connect speakers (see page 10).
B IMPEDANCE SELECTOR switch
Used to select the impedance setting (see page 11).
CONTROLS AND FUNCTIONS
8 En
This section describes the function of each button on the
remote control used to control this unit or a Yamaha CD
player.
Common controls
The following buttons can be used no matter which input
source is selected.
1 Infrared signal transmitter
Sends infrared signals.
2 A (power)
Turns this unit on, or sets it to standby mode.
This button functions only when the A (power) button on the
front panel is in the on position.
3 DIMMER
Changes the brightness level of the front panel display.
Choose brightness from 3 levels by pressing this button
repeatedly.
y
This setting is retained even if you turn off this unit.
4 SLEEP
Sets the sleep timer (see page 16).
5 Input selector buttons
Select the input source you want to listen to.
y
The input source names correspond to the names of the
connection jacks on the rear panel.
To select TUNER as the input source using the remote control,
press FM or AM.
6 OPTION
Turns the OPTION menu on and off (see page 30).
7 SPEAKERS A/B
Turns on and off the set of speakers connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel of this unit when the corresponding button is
pressed.
8 MUTE
Mutes the sound output. Press again to restore the sound
output to the previous volume level.
9 VOLUME +/
Increases or decreases the sound output level.
This does not affect the output level of the REC jacks.
0 RETURN
Returns to the previous menu or ends the menu display
when using the Option menu (see page 30).
A B / C / D / E / ENTER
Selects and confirms items in the Option menu (see page
30).
Remote control
Note
Note
CONTROLS AND FUNCTIONS
9 En
INTRODUCTION
English
FM/AM controls
The following buttons can be used when TUNER is
selected as the input source.
B TP
Searches automatically for a station that provides traffic
program (TP) broadcasts (see page 24).
C PRESET j / i
Selects a preset FM/AM station when TUNER is selected
as the input source (see page 21).
D FM, AM
Selects TUNER as the input source and sets the FM/AM
tuner band to FM or AM (see page 17).
E INFO
Turns on and changes the Radio Data System display
mode when TUNER is selected as the input source (see
page 23).
iPod controls
The following buttons can be used when DOCK is
selected as the input source for listening to an iPhone/
iPod. For more information, see page 25.
0 REPEAT
A MENU/ Ee / b / a / ENTER
E INFO
F SHUFFLE
G B
H C
Yamaha CD player controls
The following buttons can be used to control a Yamaha
CD player when CD is selected as the input source.
I Yamaha CD player control buttons
s Stops playback
e Pauses playback
p Starts playback
DISC SKIP Skips to the next disc in a CD changer
b Skips backward
a Skips forward
Ejects the disc
w Rewinds playback
f Fast-forwards playback
Even when using a Yamaha CD player, certain components and
features may not be available. Refer to your component’s owners
manual for more information.
Installing batteries Operation range
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of this unit during
operation.
Note
Using the remote control
AA, R6, UM-3 batteries
Approximately
6 m (20 ft)
Remote control
CONNECTIONS
10 En
Do not connect this unit or other components to the main power until all connections between components are
complete.
All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,
no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be
unnatural and lack bass. Refer to the owners manual for each of your components.
Use RCA cables for audio components (except for speaker connections and DOCK jack connections).
The IMPEDANCE SELECTOR must be set to the appropriate position before connecting speakers. See page 11 for
details.
Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the
speakers.
y
The PHONO jacks are designed for connecting a turntable with an MM cartridge.
Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise
without the GND connection.
CONNECTIONS
Connecting speakers and source components
CAUTION
Turntable
Audio
out
CD recorder,
etc.
DVD player,
etc.
Tape deck
GND
Audio
out
Speakers A
Subwoofer
For information about
other components that
can be connected to
this unit, see page 25.
Audio
in
Audio
out
Audio
out
Audio
in
Audio
out
Speakers B
CD player
PREPARATION
11 En
CONNECTIONS
PREPARATION
English
IMPEDANCE SELECTOR switch
Do not change the IMPEDANCE SELECTOR switch
while the power of this unit is turned on, as doing so may
damage the unit.
If the unit fails to turn on, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If this is the
case, remove the power cable and slide the switch all the
way to either position.
Select the switch position (LOW or HIGH) according to
the impedance of the speakers in your system.
Connecting speaker cables
When inserting speaker cables into the speaker terminals, insert
only the bare speaker wire. If insulated cable is inserted, the
connection may be poor and sound may not be heard.
Bi-wire connection
Bi-wire connection separates the woofer from the
combined midrange and tweeter section. A bi-wire
compatible speaker has four binding post terminals. These
two sets of terminals allow the speaker to be split into two
independent sections. With these connections, the mid and
high frequency drivers are connected to one set of
terminals and the low frequency driver to another set of
terminals.
Connect the other speaker to the other set of terminals in
the same way.
When making bi-wire connections, set the IMPEDANCE
SELECTOR switch to HIGH or LOW depending on the
impedance of your speakers:
8 Ω or higher: HIGH
4 Ω or higher: LOW
See page 11 for more information about the
IMPEDANCE SELECTOR switch.
When making bi-wire connections, remove the shorting bridges
or cables on the speaker.
y
To use the bi-wire connections, press SPEAKERS A and
SPEAKERS B on the front panel or on the remote control so that
both SP A and B light up on the front panel display.
CAUTION
Switch
position
Impedance level
HIGH
If you use one set (A or B), the impedance of
each speaker must be 8
Ω or higher.
If you use two sets (A and B) simultaneously,
the impedance of each speaker must be 16
Ω
or higher.
If you make bi-wire connections, the
impedance of each speaker must be 8
Ω or
higher. See page 11 for Bi-wire connection.
LOW
If you use one set (A or B), the impedance of
each speaker must be 4
Ω or higher.
If you use two sets (A and B) simultaneously,
the impedance of each speaker must be 8
Ω or
higher.
If you make bi-wire connections, the
impedance of each speaker must be 4
Ω or
higher. See page 11 for Bi-wire connection.
Note
Remove
approximately
10 mm (3/8 in)
of insulation
from the end of
each speaker
cable.
CAUTION
Note
This unit
Speaker
SPEAKERS A/B
SPEAKERS A/B
12 En
CONNECTIONS
Indoor antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should
provide sufficient signal strength. Connect each antenna correctly to the designated terminals.
If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center
about outdoor antennas.
Assembling the supplied AM loop
antenna
Connecting the wire of the AM loop
antenna
Plug the power cable into the AC wall outlet after all other
connections are complete.
Connecting the FM and AM antennas
Note
Indoor FM
antenna
(included)
Outdoor AM antenna
Use 5 to 10 m of vinyl-
covered wire extended
outdoors from a window.
Outdoor FM antenna
Ground (GND terminal)
For maximum safety and minimum interference, connect
the antenna GND terminal to a good earth ground. A
good earth ground is a metal stake driven into moist earth.
The AM loop antenna
should always be connected,
even if an outdoor AM
antenna is connected to this
unit.
The AM loop antenna
should be placed away from
this unit.
AM loop antenna
(included)
Connecting power cable
To the wall
outlet with the
power cable
PLAYING AND RECORDING
13 En
BASIC
OPERATION
English
Extreme caution should be exercised when you play back CDs encoded in DTS.
If you play back a CD encoded in DTS on a CD player that does not support DTS, only noise will be heard, and this noise
may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output
level of your CD player before you play back a CD encoded in DTS.
1 Press A (power) on the front panel inward to
turn on this unit.
2 Rotate the INPUT selector on the front panel
(or press one of the input selector buttons or
FM or AM on the remote control) to select the
input source you want to listen to.
3 Press SPEAKERS A and/or SPEAKERS B on
the front panel or on the remote control to
select speakers A and/or speakers B.
When speaker set A or speaker set B are turned on,
SP A or SP B is displayed on the front panel display
accordingly (see page 6).
When one set of speakers is connected using bi-wire
connections, or when using two sets of speakers simultaneously
(A and B), make sure SP A and SP B are displayed on the front
panel display.
When listening with headphones, turn off the speakers.
4 Play the source.
5 Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to adjust the sound output level.
y
You can adjust the tonal quality by using the BASS, TREBLE,
BALANCE and LOUDNESS controls, or the PURE DIRECT
switch on the front panel (see page 14).
6 When finished listening, press A (power) on
the front panel outward to turn off this unit.
y
If A (power) on the remote control is pressed while the A (power)
button on the front panel is in the on position, this unit enters
standby mode. Press A (power) again to turn this unit on.
PLAYING AND RECORDING
CAUTION
Playing a source
A (power)
SPEAKERS A/B INPUT selector
VOLUME
A (power)
Input selector
buttons
SPEAKERS A/B
VOLUME +/–
FM, AM
Notes
BASIC OPERATION
14 En
PLAYING AND RECORDING
Using the PURE DIRECT switch
Routes input signals from your audio sources so that the
input signals bypass the BASS, TREBLE, BALANCE and
LOUDNESS controls, thus eliminating any alterations to
the audio signals and creating the purest possible sound.
The PURE DIRECT indicator lights up and the front panel
display turns off after a few seconds.
The BASS, TREBLE, BALANCE, and LOUDNESS controls
do not function while the PURE DIRECT feature is turned on.
This setting is retained even if you turn off this unit.
Adjusting the BASS and TREBLE
controls
The BASS and TREBLE controls adjust high and low
frequency response.
The center position produces a flat response.
BASS
When you feel there is not enough bass (low frequency
sound), rotate clockwise to boost. When you feel there is
too much bass, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 Hz)
TREBLE
When you feel there is not enough treble (high frequency
sound), rotate clockwise to boost. When you feel there is
too much treble, rotate counterclockwise to suppress.
Control range: –10 dB to +10 dB (20 kHz)
Adjusting the BALANCE control
The BALANCE control adjusts the sound output balance
of the left and right speakers to compensate for sound
imbalance caused by speaker locations or listening room
conditions.
Adjusting the tonal quality
Notes
PURE DIRECT switch
BASS
TREBLE
BALANCE
15 En
PLAYING AND RECORDING
BASIC
OPERATION
English
Adjusting the LOUDNESS control
Retain a full tonal range at any volume level, thus
compensating for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
If the PURE DIRECT switch is turned on with the
LOUDNESS control set at a certain level, the input signals
bypass the LOUDNESS control, resulting in a sudden
increase in the sound output level. To prevent your ears or
the speakers from being damaged, be sure to press the
PURE DIRECT switch after lowering the sound output
level or after checking that the LOUDNESS control is
properly set.
1 Set the LOUDNESS control to the FLAT
position.
2 Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to set the sound output level to the
loudest listening level that you would listen
to.
3 Rotate the LOUDNESS control until the
desired volume is obtained.
y
After setting the LOUDNESS control, enjoy listening to music at
your preferred volume level. If the effect of the LOUDNESS
control setting is too strong or weak, readjust the LOUDNESS
control.
CAUTION
LOUDNESS VOLUME
VOLUME +/
16 En
PLAYING AND RECORDING
The audio from the current input source is output to the TAPE
REC and LINE 1 REC jacks. When TAPE is selected, audio is
output to the LINE 1 REC jacks only. When LINE 1 is selected,
audio is output to the TAPE REC jacks only.
This unit must be turned on in order to record.
The VOLUME, BASS, TREBLE, BALANCE and
LOUDNESS controls and the PURE DIRECT switch have no
effect on the source being recorded.
Check the copyright laws in your country before recording from
records, CDs, radio, etc. Recording copyright-protected
material may infringe on copyright laws.
1 Rotate the INPUT selector on the front panel
(or press one of the input selector buttons or
FM or AM on the remote control) to select the
source you want to record.
2 Play the source and begin recording using
the recording device connected to the REC
jacks (TAPE and/or LINE 1) on the rear panel.
See page 10.
Use this feature to automatically set this unit to standby
mode after a certain amount of time. The sleep timer is
useful when you are going to sleep while this unit is
playing or recording a source.
The sleep timer can only be set with the remote control.
1 Press SLEEP repeatedly to set the amount of
time before this unit is set to standby mode.
Each time you press SLEEP, the front panel display
changes as shown below.
The SLEEP indicator blinks while setting the amount
of time for the sleep timer.
If the sleep timer is set, the SLEEP indicator on the
front panel display lights up.
y
To cancel the sleep timer, do one of the following:
Select “Sleep Off”.
•Press A (power) on the remote control to set this unit to standby
mode.
•Press A (power) on the front panel to turn off this unit.
Recording a source
Notes
INPUT selector
FM, AM
Input selector
buttons
Using the sleep timer
Note
A (power)
A (power)
SLEEP
FM/AM TUNING
17 En
BASIC
OPERATION
English
There are 2 tuning methods; automatic and manual. Select either method according to your preference and the strength of
station signals.
Automatic tuning is effective when station signals are
strong and there is no interference.
1 Rotate the INPUT selector on the front panel
(or press FM or AM on the remote control) to
select TUNER as the input source.
If you press FM or AM on the remote control to select TUNER as
the input source, the corresponding band is also selected,
therefore you may skip step 2.
2 Press FM or AM on the front panel (or FM or
AM on the remote control) to select the
reception band (FM or AM).
FM or AM is displayed on the front panel display.
3 Press and hold TUNING jj / ii on the front
panel for more than 1 second to begin
automatic tuning.
Press ii to tune in to a higher frequency.
Press jj to tune in to a lower frequency.
When you tune in to a station, the frequency of the station is
displayed on the front panel display.
If the tuning search does not stop at the desired station because
the station signals are weak, try using the manual tuning
method.
Auto Mute feature
When listening to an FM radio station, the output will
automatically be muted when the radio signal is weak if
the station was tuned in to by:
using the automatic tuning feature
recalling a preset that was registered using the
automatic preset registration feature
If you want to listen to a station that has a weak signal,
tune in to the station manually.
FM/AM TUNING
Automatic tuning
Note
FM, AM
TUNING jj / ii
INPUT selector
FM, AM
Notes
18 En
FM/AM TUNING
Manual tuning is effective when station signals are weak.
1 Rotate the INPUT selector on the front panel
(or press FM or AM on the remote control) to
select TUNER as the input source.
If you press FM or AM on the remote control to select TUNER as
the input source, the corresponding band is also selected,
therefore you may skip step 2.
2 Press FM or AM on the front panel (or FM or
AM on the remote control) to select the
reception band (FM or AM).
FM or AM is displayed on the front panel display.
3 Press TUNING jj / ii on the front panel to
manually tune in to the desired station.
When you tune in to a station, the frequency of the received
station is shown in the front panel display.
Improving FM reception
If the signal from the station is weak and the sound quality
is not good, set the FM band reception mode to monaural
mode to improve reception.
1 Press OPTION on the remote control when
this unit is tuned in to an FM radio station.
The Option menu for TUNER is displayed (see page
30).
2 Press B / C on the remote control to select
“FM Mode”, and then press ENTER.
y
To cancel the operation and return to the Option menu, press
RETURN on the remote control.
3 Press D / E on the remote control to select
“STEREO” (automatic stereo mode) or
“MONO” (monaural mode).
When MONO is selected, FM broadcasts will be
heard in monaural sound.
When STEREO is selected and an FM station with
a stereo broadcast is tuned in, the broadcast will be
heard in stereo.
4 To exit the Option menu, press OPTION or
RETURN on the remote control.
The STEREO indicator on the front panel lights up while
listening to a station in stereo.
Manual tuning
Note
Note
FM, AM
TUNING jj / ii
INPUT selector
FM, AM
Note
OPTION
RETURN
B / C / D / E
ENTER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322

Yamaha R-S300 El kitabı

Kategori
Araba medya alıcıları
Tip
El kitabı