Yamaha V2 El kitabı

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories speciﬁed by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

speciﬁed by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

•Dit apparaat bevat een lithium batterij voor geheugen back-up.

•This apparatus contains a lithium battery for memory back-up.

•Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur afdankt

of de volgende Yamaha Service Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

•For the removal of the battery at the moment of the disposal at the

end of the service life please consult your retailer or Yamaha Service

Center as follows:

Yamaha Music Nederland Service Center

Address : Kanaalweg 18-G, 3526 KL UTRECHT

Tel: 030-2828425

•Gooi de batterij niet weg, maar lever hem in als KCA.

•Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

DME64N/DME24N Owner’s Manual

4

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited

to, the following:

• Only use the voltage speciﬁed as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the speciﬁed power cord.

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could walk

on, trip over, or roll anything over it.

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts. If

it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

•Avoid setting all equalizer controls and faders to their maximum.

Depending on the condition of the connected devices, doing so may cause

feedback and may damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not place the device in an unstable position where it might accidentally

fall over.

• Do not block the vents. This device has ventilation holes at the front and

rear to prevent the internal temperature from rising too high. In particular,

do not place the device on its side or upside down, or place it in any

poorly-ventilated location, such as a bookcase or closet.

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Otherwise, the device, TV, or radio

may generate noise.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-1

1/2

DME64N/DME24N Owner’s Manual

5

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• Be sure to connect to a properly grounded power source. A ground screw

terminal is provided on the rear panel for safely grounding the device and

preventing electrical shock.

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your ﬁngers or hand in any gaps or openings on the device

(vents, ports, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (vents, ports, etc.) If this

happens, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualiﬁed Yamaha service

personnel.

• Do not use the device or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss.

If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery. When you unplug the power

cord from the AC outlet, the internal SRAM data is retained. However, if the

backup battery fully discharges, this data will be lost. When the backup

battery is running low, the Display indicates “Low Battery” or “No Battery.”

In this case, immediately save the data to an external devices such as a

computer, then have qualiﬁed Yamaha service personnel replace the

backup battery.

Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Connections

Maintenance

Handling caution

Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

• The illustrations in this document are for instructional purposes, and may appear somewhat different from the actual equipment.

• The bitmap fonts used in this device have been provided by and are the property of Ricoh Co., Ltd.

• CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc.

• Ethernet is a trademark of Xerox Corporation.

• All other trademarks are the property of their respective holders and are hereby acknowledged.

(5)-1

2/2

Foreword

DME64N/DME24N Owner’s Manual

6

Foreword

Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine.

Using the supplied DME Designer software, the DME64N and DME24N can be easily conﬁgured to handle

a wide range of audio processing applications – institutional audio installations, sub-mixing, speaker system

control, matrix and routing, multi-effect processing, and much more.

In order to take full advantage of the features and performance provided by the DME64N/24N, we urge you

to read this owner’s manual thoroughly before use, and keep it in a safe place for future reference.

The Yamaha Pro Audio web site is at:

http://www.yamahaproaudio.com/

DME64N/DME24N Owner’s Manual

7

Foreword 8

Accessories (Please make sure the following items

are included in the package.) . . . . . . . . . . . . . . . 8

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About the Product Names . . . . . . . . . . . . . . . . . 8

About the Firmware Version . . . . . . . . . . . . . . . 8

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting the AC power cord . . . . . . . . . . . . . . . . . . . .8

Turning the power on and off. . . . . . . . . . . . . . . . . . . . . .8

Introduction to the DME64N/24N 9

Differences between DME64N/24N . . . . . . . . . 9

DME64N/24N Features . . . . . . . . . . . . . . . . . . 9

Audio System Network . . . . . . . . . . . . . . . . . . . 9

Glossary for the DME64N/24N . . . . . . . . . . . . 9

Signal Types . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Examples . . . . . . . . . . . . . . . . . . . . . . . 12

About DME Designer . . . . . . . . . . . . . . . . . . . 13

The Controls and Connectors 14

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Preparation 18

Setup Procedure. . . . . . . . . . . . . . . . . . . . . . . . 18

I/O Card Installation. . . . . . . . . . . . . . . . . . . . 20

Compatible I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . .20

I/O Card Installation Procedure . . . . . . . . . . . . . . . . . . .21

Connecting to a Computer 22

USB Connection . . . . . . . . . . . . . . . . . . . . . . . 22

Ethernet Connection ([NETWORK] Connector) 23

Audio I/O Connection 26

Analog Audio Connection ([IN] and [OUT] Connectors)

(DME24N only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

I/O Slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Connecting to an External Device 28

Remote Connection ([REMOTE] Connector). 28

Controlling external head amplifiers from the DME64N/

24N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Controlling the DME Satellite from an external device. .28

MIDI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

CASCADE Connection (DME64N only) . . . . . . . . . . .30

WORD CLOCK Connection . . . . . . . . . . . . . . . . . . . .31

GPI Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Panel Operation and Displays 33

Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . 33

Main Display. . . . . . . . . . . . . . . . . . . . . . . . . . 34

Parameter Edit Displays. . . . . . . . . . . . . . . . . . 35

Editing User Defined Button . . . . . . . . . . . . . . . . . . . . .37

Mute Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Output Level Control. . . . . . . . . . . . . . . . . . . . . . . . . . .38

Scene Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Scene Store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Spectrum Display. . . . . . . . . . . . . . . . . . . . . . . 40

Level Meter Display. . . . . . . . . . . . . . . . . . . . . 41

Initializing the DME64N/DME24N. . . . . . . . 42

Utility Displays . . . . . . . . . . . . . . . . . . . . . . . . 43

Items accessible via the Utility display. . . . . . . . . . . . . . .43

Utility Display Operation. . . . . . . . . . . . . . . . . . . . . . . .45

Info Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Network Settings (Net) Page. . . . . . . . . . . . . . . . . . . . . .45

Display Setup (Disp) Page . . . . . . . . . . . . . . . . . . . . . . .46

Security Setup (Lock) Page . . . . . . . . . . . . . . . . . . . . . . .47

Miscellaneous Setup (Misc) Page . . . . . . . . . . . . . . . . . .48

Word Clock Setup (WCLK) Page. . . . . . . . . . . . . . . . . .49

Slot Information (Slot) Page. . . . . . . . . . . . . . . . . . . . . .49

MIDI Setup (MIDI) Page. . . . . . . . . . . . . . . . . . . . . . . .50

GPI Setup (GPI) Page. . . . . . . . . . . . . . . . . . . . . . . . . . .52

Head Amplifier Setup (HA) Page . . . . . . . . . . . . . . . . . .52

Cascade Setup (CASCAD) Page . . . . . . . . . . . . . . . . . . .54

Check Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

References 55

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

ICP1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

CP4SW, CP4SF, and CP1SF . . . . . . . . . . . . . . . . . . . . .55

Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . 56

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 58

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 59

Input/Output Characteristics. . . . . . . . . . . . . . 60

Control I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Connector Pin Assign . . . . . . . . . . . . . . . . . . . 62

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . 65

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Index 72

Contents

Foreword

Introduction to

the DME64N/24N

The Controls

and Connectors

Preparation

Audio I/O

Connection

Connecting to

a Computer

Connecting to an

External Device

Panel Operation

and Displays

References

Foreword

Accessories (Please make sure the following items are included in the package.)

DME64N/DME24N Owner’s Manual

8

Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine.

In order to take full advantage of the features and performance provided by the DME64N/24N, we urge you to read this

owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.

Accessories (Please make

sure the following items are

included in the package.)

• DME64N/DM24N Owner’s Manual

(This document)

• DME Designer Installation Guide

• CD-ROM

•AC power cord

•AC plug clamp

•Euroblock plug (16P) x 2

•Euroblock plug (8P) x 4 (DME64N only)

•Euroblock plug (3P) x 16 (DME24N only)

Options

Control Panels

• ICP1 Intelligent Control Panel

• CP4SW Control Panel

• CP4SF Control Panel

• CP1SF Control Panel

About the Product Names

In this manual, models DME64N, DME24N, DME8i-C,

DME8o-C, and DME4io-C are categorized as DME

series, and models DME8i-C, DME8o-C, and DME4io-C

are all called the "DME Satellite".

About the Firmware Version

You can download the latest ﬁrmware from the following

Yamaha website.

http://www.yamahaproaudio.com/

Preparation

Connecting the AC power cord

First plug the female-connector end of the AC cord into

the [AC IN] socket on the rear panel of the DME64N/

24N, then plug the male plug into an appropriate AC

mains outlet.

Be sure to use the voltage speciﬁed for the device.

Turning the power on and off

1. Press the [POWER] switch to turn on the

power to the DME64N/24N.

2. Press the [POWER] switch again to turn off

the power.

Foreword

NOTE

For more information on your Control Panel, refer to the

owner’s manual that came with the Control Panel, as well as the

DME Designer Owner’s Manual.

Be sure to turn all devices OFF before connecting AC

mains power.

To prevent the initial power-on surge from generating a

large noise spike or damaging your speaker system, turn

the devices on in the following order: audio sources,

mixer (such as M7CL or PM5D), DME64N/24N, and

ﬁnally power ampliﬁers.

Reverse this order when turning power off.

NOTE

The DME64N/24N remembers scene settings when you turn

off the power.

When you turn on the power to the DME64N/24N, it will

start up with the same scene settings.

You can set up the DME64N/24N so that at the startup it will

recall the scene selected before you turned off the power to the

device.(page 48)

Do NOT turn off the power to the DME64N/24N

while it is receiving data from DME Designer or while it

is being manipulated from an external device. Otherwise,

a malfunction may occur.

CAUTION

Introduction to the DME64N/24N

Differences between DME64N/24N

DME64N/DME24N Owner’s Manual

9

Differences between DME64N/24N

The DME64N has four I/O card slots, while the DME24N has one I/O card slot and eight channels of built-

in analog audio I/O.

A single I/O card can handle up to 16 channels of audio I/O, so the DME64N can handle a maximum of 64

audio I/O channels. The DME24N can handle up to 24 audio I/O channels.

The DME64N has approximately double the DSP processing power of the DME24N.

DME64N/24N Features

In addition to basic mixing and matrix output functions, the DME64N/24N includes a equalizers, compressors,

delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need.

Audio System Network

Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system.

In a DME audio system, a group of the same models that can be operated in sync is called a “device group;”

audio processing divisions that accommodate multiple device groups are called “zones;” and the entire area ser-

viced by the acoustic system is called an “area.”

Each device group always includes one DME series unit that functions as the “group master” and controls all

other DME series units in the same device group.

If a computer is connected to the network, you can use the computer to control an entire device group via the

group master.

Glossary for the DME64N/24N

This section explains terminology specific to the DME64N/24N.

Components and parameters

The individual audio processing modules (equalizers, compressors, etc.) are called “components.”

External head amplifier control modules are also available as components.

Changing the parameters of components enables control over the operation of the components.

Conﬁguration

A “configuration” is a complete set of components for constructing an audio system.

Each configuration determines the audio function(s) of the corresponding DME64N/24N unit.

All parameter sets included with each component in a configuration are called “preset parameters.”

One DME64N/24N unit has a number of configurations, and a configuration has a number of preset parame-

ters.

User Deﬁned buttons

Assigning parameters to be User Defined Buttons enables you to control the device from the ICP1.

Refer to the DME Designer Owner’s Manual for details.

Introduction to the DME64N/24N

Glossary for the DME64N/24N

DME64N/DME24N Owner’s Manual

10

Scene

A combination of all configuration and preset parameters is called a “scene.”

Scenes can be recalled from an ICP1, GPI device, other external controllers, or computer.

Up to 999 scenes can be stored for each device group.

Scene structure

Scene change

16 x 8

Scene

Scene 1

Scene 2

Scene 999

Component

Configuration

Preset

Parameter

Ex.: Gate

• Attack

• Decay

• Range

• Threshold

• Key in

• Hold

Matrix Mixer

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

IN

OUT

SCENE NUMBER

12345 678

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

IN

OUT

SCENE NUMBER

12345 678

First Act Dark Change Second Act

Band Set

Play Set

Stage Stage Stage

Play

Set

Band

Set

Band Set

Play Set

Scene 1 Scene Recall Scene 2

Introduction to the DME64N/24N

Signal Types

DME64N/DME24N Owner’s Manual

11

Signal Types

DME64N/24N audio system signals can be broadly categorized as follows.

1

Audio

The DME64N/24N will be required to send and receive audio signals to and from other DME series units as

well as other audio equipment.

Audio signal transmission and reception will occur primarily via the [INPUT] and [OUTPUT] connectors on

the DME24N.

2

Device group control

Device group control signals control all DME series devices in the group.

There are two types of device group control signals, as follows:

• Control signals between the computer and the group master DME series unit

• Control signals between the group master DME series unit and the other DME series

units

You can use the DME Designer application to control the entire device group, such as sending components to

the devices and setting the parameters as required.

3

Device control

These signals provide communication and control between individual devices.

Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred be-

tween [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector.

Type of signals handled by the DME64N/24N

Connector Audio Signal Device Group Device Control Word Clock Page

[USB]

Connector

– Control signals from

computer to Device Group

master DME series unit.

Transmission/reception of

control signals (MIDI

commands) between

computer and DME64N/

24N.

–22

[NETWORK]

Connector

–

• Control signals between the

computer and the group master DME

series unit

• Control signals between the group

master DME series unit and the other

DME series units

Transmission/reception of

control signals between

computer and DME series

units

–23

[MIDI]

Connector

––Transmission/reception of

control signals (MIDI

commands) between MIDI

controller and DME64N/

24N.

–29

[GPI]

Connector

––Input/output of GPI control

signals between GPI device

(GPI controller, etc.) and

DME series unit

–32

[CASCADE]

Connector

(DME64N

only)

32 channels of

input/output.

Control signals from mixer to

Device Group master

DME64N.

–Word clock transmission

and reception to and from

other devices.

30

[WORD

CLOCK]

Connector

–– –Word clock transmission

and reception to and from

other devices.

31

[REMOTE]

Connector

––

• Transmission/reception of control

signals to/from an external device

(such as AD8HR head ampliﬁer)

• Transmission/reception of MIDI

messages

–28

(Audio I/O

Connectors)

(DME24N

only)

8 channels of

input and

output.

–––26

(I/O Slot) Number of I/O

channels

depends on

card.

– Serial signal transmission/

reception (depending on

function of card).

Word clock transmission

and reception to and from

other devices (depending

on function of card).

27

Introduction to the DME64N/24N

System Examples

DME64N/DME24N Owner’s Manual

12

System Examples

Multiple DME Series units: Large-scale system

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

USB

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

INPUT

DIGITAL MIXING ENGINE SATELLITE

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

IN

OUT

SCENE NUMBER

12345 678

96kHz

88.2kHz

48kHz

44.1kHz

EXT.

CLOCK

MID

MASTER

NETWORK

PEAK

SIGNAL

PEAK

SIGNAL

IN

OUT

SCENE NUMBER

12345 678

DME8o-C

DME8i-C

DME24N

DME64N

DME24N

MY16-CII MY8-ADDA96

MY16-CII x 4

MY8-ADDA96

ICP1

Computer

Hub

Space BSpace A

Space C

Space D

Analog In

Analog Out

Analog In

Analog Out

Ethernet

CobraNet

Ethernet Switching Hub

CobraNet Switching Hub

Analog Out

Analog In

Analog Out

Introduction to the DME64N/24N

About DME Designer

DME64N/DME24N Owner’s Manual

13

About DME Designer

DME Designer software enables you to integrate, configure, and control the DME series system from a con-

nected computer.

You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the

computer monitor.

The DME series settings, configuration, and parameter data are transferred from the computer to the DME se-

ries unit via the USB or Ethernet connection.

Once the data is transferred to the unit, you can disconnect the DME series unit from the computer and use it

as a stand-alone processor.

Alternatively, you can control the DME series unit real-time from DME Designer as long as it is connected to

a computer.

If multiple DME series units are connected in the network, DME Designer enables you to build a configuration

that includes those units.

Refer to the “Connecting to a Computer” (page 22) for more information on connecting a computer to the

DME64N/24N. Refer to the DME Designer Installation Guide for detailed information on installing the DME

Designer application and required software drivers.

Refer to the DME Designer Owner’s Manual for setup and operation instructions.

The Controls and Connectors

Front Panel

DME64N/DME24N Owner’s Manual

14

Front Panel

1 [USB] Connector

A computer can be connected here when it is necessary to

program or control the device. When a USB connection is

to be used, the USB-MIDI driver must be installed on the

computer. Refer to the DME Designer Installation Guide

for installation instructions.

2 [EXT. CLOCK] Indicator

When a clock signal from an external device is selected, the

indicator will light green. If the clock signal is not

appropriate the indicator will ﬂash red. The indicator will

go out when the internal word clock is selected.

3 [96kHz] [88.2kHz] [48kHz] [44.1kHz]

Indicator

Normally, the indicator corresponding to the current word

clock frequency will light green. If a problem with the

master clock is detected all of these indicators will ﬂash red.

2 seconds after a problem is detected with an external

master clock the internal clock will temporarily be selected.

When this happens the indicator corresponding to the

frequency of the internal clock will light green, and all

other indicators will continue to ﬂash red.

4 [NETWORK] Indicator

Lights while data communication is occurring via the

[USB], [NETWORK], or [CASCADE] connector.

Received data causes the indicator to light in green, while

transmitted data causes the indicator to light in orange. If a

problem occurs the indicator will light in red.

The Controls and Connectors

HOMEHOME UTILITYUTILITYSCENESCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

HOMEHOME UTILITYUTILITYSCENE LEVELLEVEL MUTEMUTE

ENTERENTERCANCELCANCEL

1

2

4

5

6

7

8

7

8

9

)

^

&

^

&

º

¡

™

£

º

¡

™

£

*(

! @#$%

2

4

5

6

3

DME64N

DME24N

The Controls and Connectors

Front Panel

DME64N/DME24N Owner’s Manual

15

5 [MIDI] Indicator

Lights while data communication is occurring via the

[MIDI] connector. Received data causes the indicator to

light green, while transmitted data causes the indicator to

light orange. The indicator will light green when reception

and transmission occur simultaneously. If a problem occurs

the indicator will light red.

6 [MASTER] Indicator

Lights green when the device is operating as the device

group master (page 9). The indicator will not light if the

device is operating as a device group slave. Refer to page 45

for device group master setup instructions.

7 [PEAK] Indicator (DME24N only)

Light red when a signal on the corresponding built-in

analog audio input or output ([IN] and [OUT]

connectors) reaches or exceeds -3 dB.

8 [SIGNAL] Indicator (DME24N only)

Light green when a signal with a level greater than -40 dB

is present at the built-in analog audio inputs and outputs

([IN] and [OUT] connectors).

9 [SCENE NUMBER] Indicator

Shows the current scene number.

) Display

Displays scene information and device parameters.

! [SCENE] Button

Calls the scene recall/store display (page 38). The scene

store display will appear if the button is held for longer

than 2 seconds (page 39). The indicator will light green

while the scene recall or store display is showing.

@ [HOME] Button

Directly recalls the home (main) display. If pressed while

the main display is showing the [HOME] button steps

through the user-deﬁned parameter display pages (refer to

page 37 in this manual).

# [UTILITY] Button

Calls the output level display. If this button is held for

longer than 2 seconds while the main display is showing

the utility display will appear. Switches between the Utility

display pages if pressed while the Utility display is showing.

$ [LEVEL] Button

Calls the output level setup display (page 38).

The indicator will light green.

% [MUTE] Button

Calls the mute display (page 38). The indicator will light

orange when mute is on. The indicator will light green

when mute is off and the mute display is showing, and will

be off if the mute display is not showing.

^ Dial

Adjusts the value of selected parameters.

& [E] [ ▲ ] [ ▼ ] [F] Buttons

Move the display cursor in the corresponding directions.

* [CANCEL] Button

Closes the window on the display.

( [ENTER] Button

Conﬁrms and enters a value or setting.

º [PHONES] Jack

A pair of headphones can be plugged in here.

¡ [PHONES LEVEL] Control

Adjusts the headphone volume. Even when the control is

set to the minimum level, the sound at the headphones is

not completely muted.

™ [MONITOR] Button

Calls the monitoring point slot selection display (page 39).

When the [ENTER] button is pressed to select a slot, the

monitoring point selection display will appear.

The spectrum analyzer display will then appear when the

[ENTER] button is pressed to select a monitoring point.

The indicator will light green while the monitoring slot/

point or spectrum analyzer display is showing.

£ [POWER] Switch

Turns mains power to the device on and off.

NOTE

The DME64N has no built-in analog audio inputs or outputs

([IN] and [OUT] connectors).

The Controls and Connectors

Rear Panel

DME64N/DME24N Owner’s Manual

16

Rear Panel

1 [AC IN] Connector

This is the device’s three-pronged AC power connector.

Connect to the AC mains using the supplied AC power

cord. See “Preparation” on page 8 for details.

2 Ground Screw

The supplied power cable has a three-prong plug that will

ground the unit when plugged into an appropriate three-

prong type AC mains outlet. When connecting to a two-

prong type outlet that has a ground screw, use the supplied

AC plug adaptor and connect the adaptor’s ground lead to

the ground screw. When connecting to a two-prong type

outlet that does not have a ground screw be sure to connect

the DME64N/24N ground screw to a conﬁrmed ground

point. Proper grounding can signiﬁcantly reduce hum,

noise, and interference, while stabilizing phase and

imaging.

3 [GPI] Connector

This Euroblock connector provides access to the unit’s GPI

(General Purpose Interface) interface for transfer of control

signals to and from external equipment. The DME64N

provides 16 channels of GPI input and output, while the

DME24N provides 8 channels. Each input channel has an

IN terminal and a +V terminal. Output channels each have

an OUT terminal and a GND terminal. The open voltage

at the +V terminal is 5V, while the IN terminal detects

voltage changes from 0V ~ 5V. The OUT terminals output

either 0V or 5V. See “GPI Connection” on page 32 for

connection details.

3

8

32

21

)6574

1

9

5674

9

DME64N

DME24N

NOTE

Use the supplied AC cord clamp to prevent accidental

disconnection of the AC power.

NOTE

When connecting to two-prong type AC mains outlets use the

supplied plug adaptor.

NOTE

Make sure that the device is securely grounded to a single ground

point (e.g. either via a three-prong AC connection, or via the

ground screw.)

NOTE

Connect the device to only one ground point.

Connecting the device to more than ground point can result in

ground loops that can cause increased hum and noise.

The Controls and Connectors

Rear Panel

DME64N/DME24N Owner’s Manual

17

4 [MIDI IN] [MIDI OUT] [MIDI THRU]

Connectors

These are standard MIDI connectors that handle reception

and transmission of MIDI data: [MIDI IN] receives MIDI

data, [MIDI OUT] transmits MIDI data, and [MIDI

THRU] re-transmits MIDI data received at the [MIDI

IN] connector. See “MIDI Connection” on page 29 for

connection details.

5 [WORD CLOCK IN] [WORD CLOCK OUT]

Connectors

These BNC connector receive and transmit word clock

from and to external equipment. See “Word Clock

Connection” on page 31 for connection details. Word

clock settings are available via the device’s Utility display

WCLK page (see page 49 of this document).

6 [NETWORK] Connector

This is a 100Base-TX/10Base-T Ethernet connector for

connection to a computer or other DME64N/24N units.

Normally this connector will be connected to a network

hub via an Ethernet “straight” cable. When two

DME64N/24N units are to be directly connected a “cross”

cable should be used.

7 [REMOTE] Connector

This 9-pin D-SUB connector allows connection to

Yamaha AD824 or AD8HR remote head ampliﬁers or

other RS-232C compatible controllers. Refer to page 28

for connection details.

8

[IN] [OUT] Connectors (DME24N only)

These are balanced Euroblock connectors for analog audio

input and output. The analog signal from microphones or

line sources such as CD players can be input via the IN

connectors, while the OUT connectors can deliver analog

output to powered speakers or recording equipment. 48V

phantom power can be supplied to the IN connectors

(page 52). Refer to page 26 for [IN] and [OUT]

connection details.

9 I/O Slots

Optional Yamaha or third-party mini-YGDAI cards can be

plugged in here for system expansion. The DME64N has

four I/O slots, while the DME24N has one.

One expansion card can be plugged into each slot. Refer to

“I/O Card Installation” on page 20 for installation details.

) [CASCADE IN] [CASCADE OUT]

Connectors (DME64N only)

This 68-pin D-SUB connector can be connected to the

CASCADE connector of other devices via a dedicated

cascade cable. The CASCADE connector transmits and

receives control, audio, and word clock signals. Refer to

“Cascade Connection” on page 30 for connection details.

NOTE

Use a CAT5 STP (Shielded Twisted Pair) cable for this

connection to prevent electromagnetic interference.

NOTE

The [IN] and [OUT] connectors each have 24 terminal pins.

Each of the eight inputs and outputs uses three pins – hot, cold,

and ground. Use the supplied 3-pin Euroblock plugs to connect

to the appropriate inputs and outputs.

Preparation

Setup Procedure

DME64N/DME24N Owner’s Manual

18

Setup Procedure

Follow the steps outlined below to prepare the DME64N/24N for operation.

1.Install any required I/O cards.

Refer to “I/O Card Installation” on page 20 for details.

2.Connect the AC power cord.

Be sure to turn all devices OFF before connecting AC mains power.

Attach the cable clamp to prevent accidental disconnection.

Attaching the cable clamp.

Be sure to properly ground the device to prevent possible electrical shock.

First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the

DME64N/24N, then plug the male plug into an appropriate AC mains outlet. Make sure the AC power to be

used complies with the conditions marked on the top cover of the device.

Use only the AC power cord supplied with the DME64N/24N. If the supplied cord is lost or damaged and needs to

be replaced, contact your Yamaha dealer. The use of an inappropriate replacement can pose a ﬁre and shock hazard!

The type of AC power cord provided with the DME64N/24N may be different depending on the country in which

it is purchased (a third prong may be provided for grounding purposes). Improper connection of the grounding

conductor can create the risk of electrical shock. Do NOT modify the plug provided with the DME64N/24N. If the

plug will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician. Do not use a plug adapter which

defeats the grounding conductor.

Preparation

Security Cover Mounting

Security cover mounting screw holes (M3 size) are provided on the front panel of the unit. The spacings are

423mm width and 96mm (DME64N) / 52mm (DME24N) height. See “Dimensions” on page 64 for

details. A security cover made by the customer or contractor can be attached to the front panel via these

mounting holes to prevent accidental operation. Yamaha cannot supply a security cover.

When mounting a cover make sure that the screws used do not go deeper than 15 millimeters into the front

panel. Also, to ensure that the cover does not come in contact with the panel controls, leave a space of about

20 millimeters between the front panel and the cover.

CAUTIO

N

W

ARNIN

G

Preparation

Setup Procedure

DME64N/DME24N Owner’s Manual

19

3.Install the DME Designer software and necessary drivers on the computer to be used for

device group control.

See the separate “DME Designer Installation Guide” for details.

4.Connect devices.

•Network connection

Ethernet connection (page 23)

USB connection (page 22)

• Analog connection (page 26)

•External device connection

Remote connection (page 28)

MIDI connection(page 29)

CASCADE connection(page 30)

WORD CLOCK connection(page 31)

GPI connection (page 32)

5.Turn power to the computer, DME64N/24N, and related devices on. Press the DME64N/24N

[POWER] switch to turn it on.

To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn

devices on in the following order: audio sources, mixer and/or recorders, and ﬁnally power ampliﬁers. Reverse this

order when turning power off.

No information will appear on the display the ﬁrst time the device is turned on. The appropriate scene and

other data must ﬁrst be transferred to the device from the DME Designer.

Refer to the DME Designer Manual for details.

Once the appropriate data has been transferred to the device, the current number and name will appear on the

display:

If any scene data has been stored in the DME64N/24N, the current scene and its name will be displayed.

6.Set up the DME64N/24N operation parameters.

See the “Utility Display” section on page 43 for details.

NOTE

The “NET” page settings must be set up as required before using the unit for the ﬁrst time.

CAUTIO

N

Preparation

I/O Card Installation

DME64N/DME24N Owner’s Manual

20

7.Launch the DME Designer application, create conﬁguration and transfer.

DME Designer setup, operation, and data transfer instructions can be found in the DME Designer Manual.

This completes preparation of the DME64N/24N system.

I/O Card Installation

The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels

available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available card

slot(s).

Compatible I/O Cards

As of July 2004, Yamaha mini-YGDAI cards that can be used with the DME64N/24N are as follows:

The input/output numbers above apply to 44.1/48kHz operation.

(*)

In Version 1.0, only two MY16-C cards could be used simultaneously in the DME64N.

If the serial number written on the upper surface of your DME64N is shown below, a hardware upgrade is needed.

KK, KL, KM, KN, KO, KP, KX, KY are the third and fourth digits of the serial number.

A fee is charged for the hardware upgrade.

For details, contact Yamaha customer support using the contact information located at the end of the “DME64N/24N Owner’s

Manual.”

For the latest information on what cards can be used with the DME64N/24N, visit the Yamaha Pro Audio

website at: http://www.yamahaproaudio.com/

Card Name Function Input Output

No. of Available Cards

DME64N DME24N

MY8-AT ADAT 8 8 4 1

MY8-TD TDIF-1 8 8 4 1

MY8-AE AES/EBU 8 8 4 1

MY4-AD ANALOG IN 4 – 4 1

MY8-AD ANALOG IN 8 – 4 1

MY4-DA ANALOG OUT – 4 4 1

MY8-AD24 ANALOG IN 8 – 4 1

MY8-AD96 ANALOG IN 8 – 4 1

MY8-DA96 ANALOG OUT – 8 4 1

MY8-ADDA96 ANALOG IN/OUT 8 8 4 1

MY8-AE96S AES/EBU 8 8 4 1

MY8-AE96 AES/EBU 8 8 4 1

MY16-AT ADAT 16 16 4 1

MY16-AE AES/EBU 16 16 4 1

MY16-TD TDIF-1 16 16 4 1

MY16-C CobraNet 16 16 4(*) 1

MY16-CII CobraNet 16 16 4 1

Sayfa yükleniyor...

Yamaha V2 El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha V2 El kitabı

diğer dillerde

İlgili makaleler

Diğer belgeler