Yamaha CDR-D651 El kitabı

Kategori
CD çalar
Tip
El kitabı
DISC B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia V647790-1
GB
CDR-D651
CDR-D651
Compact Disc Recorder
OWNER'S MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
(For U.K., Europe, General models)
(For U.K., Europe, General, and Australia models)
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereses.
ACHTUNG
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit
gefährlichen Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller
genomförande av procedurer andra än de som
specificeras i denna bok kan resultera i att du utsätter
dig för farlig strålning.
ATTENZIONE
Uso di controlli o regolazioni o procedure non
specificamente descritte può causare l’esposizione a
radiazioni di livello pericoloso.
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste
o utilización diferentes de los especificados en este
manual pueden causar una exposición peligrosa a la
radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of
uitvoeren van handelingen anders dan staan
beschreven in deze handleiding kunnen leiden tot
blootstelling aan gevaarlijke stralen.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
CAUTION - VISIBLE AND
/
OR INBISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO BEAM.
VARNING -
-
SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARNING SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VARO !
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
/
TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
VORSICHT !
SICHTBARE UND
/
ODER UNSICHTBARE
LASERATRAHLUNG WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETZEN.
ANALOG
LINE IN
REC
4
PLAY
3
LINE OUT
R
L
R
L
DIGITAL
OPTICAL
IN OUT
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
ANALOG
LINE IN
REC
4
PLAY
3
LINE OUT
R
L
R
L
DIGITAL
OPTICAL
IN OUT
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
CAUTION - VISIBLE AND
/
OR INBISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO BEAM.
VARNING -
-
SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARNING SYNLIG OCH
/
ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VARO !
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
/
TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
VORSICHT !
SICHTBARE UND
/
ODER UNSICHTBARE
LASERATRAHLUNG WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETZEN.
E-1
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
GETTING STARTED
Introduction
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best
performance, read this manual carefully. It will guide you in operating your YAMAHA product.
ENGLISH
Features
Double Speed CD DIRECT Copy
CD-R/CD-RW Recording and Playback
Double Speed Finalization
Optical Digital Input and Output
Various Playback Functions for 2 CDs
Relay Play, Program Play
Repeat Play, Random Play
CD TEXT Compatible
Contents
GETTING STARTED
Contents ........................................................... 1
PRECAUTIONS ............................. 2
DISCS COMPATIBLE WITH THIS UNIT .. 3
PREPARATION .............................. 4
Supplied Accessories ....................................... 4
Remote Control ................................................ 5
Connections ..................................................... 6
CD Preventive Care........................................... 7
CONTROLS AND FUNCTIONS ............ 8
Front Panel ....................................................... 8
Remote Control ................................................ 9
Display ........................................................... 10
Menu Setting .................................................. 11
RECORDING
RECORDING TO A DISC ................. 12
Basic Recording Operation ............................. 12
Selecting an Input Source .............................. 14
Selecting a Recording Mode .......................... 14
Setting the Recording Level ........................... 15
Manual Track Marking .................................... 15
RECORDING FUNCTIONS ............... 16
CD DIRECT Copy ............................................ 16
Synchronized Recording ................................ 16
Track and Disc Erase (CD-RW discs only) ...... 18
REC Mute ....................................................... 19
Fade In/Fade Out Function .............................. 19
CD TEXT Copying and Editing ........................ 19
FINALIZATION ............................ 21
Finalization ..................................................... 21
PLAYBACK
PLAYING 1 OR 2 CDS.................... 22
Basic Playback Operation ............................... 22
Relay Playback of 2 CDs................................. 22
Searching ....................................................... 23
Skipping Tracks .............................................. 23
PLAYBACK FUNCTIONS ................. 24
Program Play ................................................. 24
Random Play .................................................. 25
Single Repeat ................................................. 26
Full Repeat ..................................................... 26
Repeat Relay .................................................. 26
Random Repeat.............................................. 26
Listening with Headphones ............................ 27
Auto Play ........................................................ 27
ADDITIONAL INFORMATION
ADDITIONAL INFORMATION ........... 28
CD-Recorder System Notes and Limitations .. 28
SCMS Copy Protection ................................... 28
Display Messages .......................................... 29
Troubleshooting ............................................. 30
Specifications ................................................. 31
E-2
PRECAUTIONS: READ THIS BEFORE OPERATING THIS UNIT ............
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean place
with at least 5 cm of ventilation space on the top, right
and left, and at the back of this unit – away from direct
sunlight, heat sources, vibration, dust, moisture, and/or
cold.
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds. To
prevent fire or electrical shock, do not place this unit
where it may get exposed to rain, water, and/or any type
of liquid.
Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in a
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit, which
may cause an electrical shock, fire, damage to this unit,
and/or personal injury.
On the top of this unit, do NOT place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may cause
electrical shock to the user and/or damage to this unit.
Do not cover the rear panel of this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all connections
are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
Take care of this unit so that no foreign objects and/or
liquid drops inside this unit.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the
wall outlet.
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that this unit
is faulty.
Before moving this unit, first check that there is no disc in
the disc tray. To prevent damage to this unit, be sure to
insert the transportation pad in the disc tray. Finally,
press POWER to turn off this unit, and disconnect the AC
power plug from the wall outlet. After this unit is moved,
remove the pad to ensure correct operation.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wires in the mains lead are coloured in accordance with the
following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows: The wire which is
coloured BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK. The wire which is
coloured BROWN must be connected to the terminal which is
marked with the letter L or coloured RED. Making sure that
neither core is connected to the earth terminal of the three pin
plug.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
Voltage Selector (General model only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging into
the AC power supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
E-3
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
....................................... DISCS COMPATIBLE WITH THIS UNIT
Discs that can be used for recording
Be sure to use only CD-R and CD-RW discs made by
reliable manufacturers.
CD-R and CD-RW digital audio discs that display either of
the following marks can be used with this unit.
In addition to these marks being present on the disc, check
that at least one of the following phrases can also be found
on the disc or disc case.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
Regarding discs that can be used for recording
CD-R discs can only be recorded on once, and the recorded
material cannot be erased.
CD-RW discs can be recorded on, have the recorded material
erased, and then recorded on again any number of times.
The following discs cannot be used for recording on
this unit.
Discs bearing marks other than those shown above.
Discs intended for recording computer data.
Discs intended for professional use or labeled “FOR
PROFESSIONAL USE ONLY”.
Finalization of CD-R discs for playback on
standard CD players
Although a partially recorded CD-R disc can be played on
this unit, it cannot be played on a standard CD player until it
has undergone a process known as “finalization”. In the
finalization process, the Table of Contents (TOC) is written
onto the disc and further recording is not possible.
However, this process makes it possible to play a CD-R
disc on a standard CD player.
Some CD players may not play back the finalized CD-R
discs properly due to differences in the playback system of
different manufacturers.
See page 21 for the finalization procedure.
Regarding erasure or loss of data
Yamaha and suppliers accept no liability for the loss of data
or any problems caused as a result. As a precaution, it is
recommended that the discs are tested after they have
been written to. Furthermore, under no circumstances does
Yamaha and suppliers guarantee the reliability of the discs.
Discs that can be played back
In addition to CD-R and CD-RW digital audio discs
described above, commercially available pre-recorded CDs
bearing the mark shown below can also be played on this
unit.
Playback of CD-RW discs
Please note that even after a CD-RW disc has been
finalized, it still cannot be played on a standard CD player.
CD-RW discs can only be played back on CD-RW
compatible players such as this unit.
Additionally, CD-RW discs can be erased even after
finalization has been performed, and recorded onto again.
Playback on DVD players
Before playing back a finalized CD-R or CD-RW discs on a
DVD player, please check whether the DVD player is
compatible with CD-R or CD-RW discs or not. Refer to the
owner's manual of the DVD player for more information. If
the DVD player is not compatible with CD-R or CD-RW
discs, do not attempt to play them on the DVD player.
Note
Please check the copyright laws in your country to
record from records, compact discs, radio, etc.
Recording of copyright material may infringe copyright
laws.
E-4
PREPARATION..................................................................
Supplied Accessories
After unpacking, make sure the following items are included in your package.
Remote Control Batteries (size AA, UM-3, R6) (2)
Optical Fiber Cable (1)
RCA Pin Cables (2)
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
TIME TEXT DIMMER
0
SPACE
+10
SYMBOL
PROG
DISPLAY
A
/
B
INPUT
OPEN
/
CLOSE
B
REPEAT RANDOM
CLEAR
MENU
EDIT DELETE SET
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
A B
Ferrite core for headphones cable (1)
(U.S.A., Canada, and Australia model only)
When using headphones, be sure to attach the ferrite core
provided to the headphones cable in order to reduce the
electromagnetic interference. Open the cover and fit the
core onto the headphones cable as the illustration below
shows.
E-5
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
NATURAL SOUND CD RECORDER CDR–D651
POWER
DISC
A
DISC
B
DISPLAY A TEXT
/
TIME DISPLAY B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
PHONES LEVEL
MIN MAX
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
30°
30°
.................................................................. PREPARATION
Remote Control
Remote control operation range
Notes
There should be no large obstacles between the remote control
and this unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.), it
might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
Within approximately 6 m
(20 feet)
Loading the batteries in the remote control
1.
Remove the battery compartment cover on the
back of the remote control.
2.
Insert the batteries (AA, UM-3 or R6 type)
according to the polarity markings on the inside of
the battery compartment.
3.
Close the battery compartment cover.
Battery replacement
If you find that the remote control must be used closer to
this unit than usual, the batteries are weak. Replace
batteries with new ones.
Notes
Use only AA, UM-3, R6 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside the
battery compartment.)
Remove the batteries if the remote control will not be used for an
extended period of time.
If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before installing
new batteries.
2
1
3
Remote control
sensor
E-6
PREPARATION..................................................................
Connections
Turn off the power of this unit and the other component, and unplug them from the wall outlet before making any
connections.
Correctly connect the input and output jacks on this unit to the input and output jacks on the other component.
Arrow marks () in the illustration below indicate the direction of the audio signal.
Digital connections
Remove the jack covers for DIGITAL IN OPTICAL and DIGITAL OUT OPTICAL before starting to make connections.
Using the optical fiber cable, connect the DIGITAL IN OPTICAL on this unit to the DIGITAL OUT OPTICAL on the other
component, and the DIGITAL OUT OPTICAL on this unit to the DIGITAL IN OPTICAL on the other component.
Keep the jack covers for future use. Replace them in order to protect the digital jacks from dust when the jacks are not
being used.
Analog connections
Make sure to correctly connect the L (left) and R (right) ANALOG LINE IN (REC) and ANALOG LINE OUT (PLAY) jacks
on this unit to the L (left) and R (right) ANALOG LINE OUT (REC) and ANALOG LINE IN (PLAY) jacks on the other
component.
Connect the ANALOG LINE IN (REC) jack on this unit to the ANALOG LINE OUT (REC) jack on the other component,
and the ANALOG LINE OUT (PLAY) jack on this unit to the ANALOG LINE IN (PLAY) jack on the other component.
The ANALOG LINE IN (REC) and ANALOG LINE OUT (PLAY) jacks on this unit are numbered 4 and 3 respectively.
Connect these jacks to the jacks with same numbers when connecting this unit with YAMAHA amplifier or receiver.
Plug in this unit to a wall outlet when all connections are complete.
ANALOG
LINE IN
REC
4
PLAY
3
LINE OUT
R
L
R
L
DIGITAL
OPTICAL
IN OUT
REC
VOLTAGE SELECTOR
PLAY
OUT
IN
DIGITAL IN DIGITAL OUT
OPTICAL OPTICAL
R
L
R
L
110V
120V
220V
240V
RCA pin cable
(included)
RCA pin cable
(included)
Optical fiber cables
(One included)
To wall outlet
Amplifier or Receiver
Voltage Selector
(General model)
E-7
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
.................................................................. PREPARATION
CD Preventive Care
This compact disc recorder is designed for use with
compact discs bearing the , , , or marks
only. Never attempt to load any other type of disc into
this unit.
This unit will also play 8-cm (3-inch) compact discs.
Compact discs are not subjected to wear during play,
but damage to the disc surface when the disc is being
handled can adversely affect the disc’s play.
Do not use cleaning discs or warped discs. All of these
could damage the unit.
To prevent a malfunction of this unit
Do not use any non-standard shaped CDs (heart, etc.)
available on the market, because it may damage this
unit.
Do not use a CD with tape, seals, or paste on it, because
damage to this unit may result.
Be sure to use a felt-tip pen or similar writing tool when
writing on the label side of the disc. Do not use a ball-
point pen, pencil, or other hard-tipped writing tool, as
these may damage the disc and may aversely affect
further recording on the disc.
Although playback of compact discs is generally not
affected by small particles of dust or fingerprints on their
playing surface, dust, fingerprints, small scratches and
direct sunlight on the recording surface of a CD-R or
CD-RW disc may make recording impossible. Therefore,
for optimal performance of the recorder and for long-
term enjoyment of your CD collection, handle discs
correctly as outlined in the following guidelines.
Hold discs by touching only the edges or center hole.
When a disc is not currently being used, remove it
from the recorder and store in an appropriate case.
With proper disc maintenance, cleaning should not
be necessary. However, should cleaning be required,
wipe by using a clean, dry cloth. Do not wipe with a
circular motion; wipe straight outward from the
center.
Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, antistatic spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the disc’s surface.
Do not expose discs to direct sunlight, high temperature,
or high humidity for a long period of time, because these
might warp or otherwise damage the disc.
No!
E-8
CONTROLS AND FUNCTIONS .................................................
Front Panel
NATURAL SOUND CD RECORDER CDR–D651
POWER
DISC
A
DISC
B
DISPLAY A TEXT
/
TIME DISPLAY B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
PHONES LEVEL
MIN MAX
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
1234567890qwerty
uiopasdfghjkl;
1 POWER...................................................... P.12,22
2 Disc tray A.................................................. P.14,16
3 Display ............................................................ P.10
4 v (Open/Close for disc tray A)
5 DISPLAY A ..................................................... P.10
6 TEXT/TIME ................................................ P.10,20
7 DISPLAY B ..................................................... P.10
8 v (Open/Close for disc tray B)
9 Remote control sensor
0 COPY .............................................................. P.16
q FINALIZE ........................................................ P.21
w REC MODE ................................................ P.16,17
e TRACK NO. .................................................... P.15
r ERASE ............................................................ P.18
t INPUT......................................................... P.13,14
y MULTI JOG........................................... P.11,15,16
u Disc tray B.................................................. P.12,16
i ANALOG REC LEVEL ................................... P.15
o REC FADE IN/OUT .............................. P.13,15,19
p REC MUTE ..................................................... P.19
a r/y (Skip/Search for disc tray B)
s t/e (Skip/Search for disc tray B)
d a (Stop for disc tray B)
f w/d (Play/Pause for disc tray B)
g PHONES LEVEL ............................................ P.27
h PHONES ......................................................... P.27
j w/d (Play/Pause for disc tray A)
k a (Stop for disc tray A)
l r/y (Skip/Search for disc tray A)
; t/e (Skip/Search for disc tray A)
E-9
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
...................................................CONTROL AND FUNCTIONS
Remote Control
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
TIME TEXT DIMMER
0
SPACE
+10
SYMBOL
PROG
DISPLAY
A
/
B
INPUT
OPEN
/
CLOSE
B
REPEAT RANDOM
CLEAR
MENU
EDIT DELETE SET
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
A B
1
2
3
4
5
6
7
8
9
0
q
w
e
r
t
y
u
i
o
p
a
s
d
f
g
h
j
k
l
;
z
x
1 COPY .............................................................. P.16
2 OPEN/CLOSE A, B
3 REC FADE IN/OUT .............................. P.13,15,19
4 REC MUTE ..................................................... P.19
5 REC MODE ................................................ P.16,17
6 DISPLAY A/B ................................................. P.10
7 TIME................................................................ P.10
8 TEXT .......................................................... P.10,20
9 MENU......................................................... P.11,16
0 EDIT ................................................................ P.20
q DELETE .......................................................... P.20
w Alphabetical/Numeric buttons ................... P.20,23
e REPEAT.......................................................... P.26
r RANDOM ........................................................ P.25
t e (Search)
y d (Pause)
u t (Skip)
i A (Disc tray A) ................................................ P.24
o TRACK NO. WRITE ....................................... P.15
p ERASE ............................................................ P.18
a FINALIZE ........................................................ P.21
s INPUT......................................................... P.13,14
d DIMMER.......................................................... P.10
f +, ............................................................. P.11,16
g SET ................................................................. P.20
h PROG......................................................... P.24,25
j CLEAR ............................................................ P.25
k r (Search)
l y (Skip)
; w (Play)
z B (Disc tray B) ................................................ P.24
x a (Stop)
E-10
CONTROL AND FUNCTIONS ...................................................
Display
The display located in the center of this unit provides
information about disc A and disc B. Press DISPLAY A or
DISPLAY B on the front panel (DISPLAY A/B on the
remote) to select the disc information you wish to see.
Displays during recording
Recording is done on disc tray B. While recording is being
done, each time TEXT/TIME (TIME on the remote) is
pressed, the display changes as follows:
Elapsed time of the track being recorded
When recording from the LINE IN jack
When making a copy from disc tray A
Total time recorded on the disc
Total remaining recording time on the disc
Displays during playback
While a disc is being played, each time TEXT/TIME (TIME
on the remote) is pressed, the display changes as follows:
Elapsed time of the track being played
Remaining time of the track being played
Open
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Disc tray A Disc tray B
2 1:41
CD–R
44.I
REC
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
8 2 1:41
CD–R
44.I
REC
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
2 7:32
CD–R
44.I
REC
TOTAL
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
2 67:07
CD–R
44.I
REC
TOTAL
REMAIN
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
1 0:12
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
1 4:27
REMAIN
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Total disc play time
Total remaining time on the disc
CD-TEXT displays
This unit is CD-TEXT compatible. When playing a CD with
CD-TEXT data, the disc name and track name are
displayed following after the total remaining time on the
disc, by pressing TEXT/TIME on the front panel. When
using the remote control, press TEXT to display the disc
name and track name.
When the name contains more than 10 characters, the first
10 characters are displayed after the entire name is shown
scrolled.
Display brightness
The brightness of the display can be changed in three
degrees by pressing DIMMER on the remote.
1 54:36
TOTAL
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
1 54:24
TOTAL
REMAIN
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
BEATLES BE
CD
TITLE
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
YESTERDAY
CD
TRACK
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Disc name
Track name
E-11
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
...................................................CONTROL AND FUNCTIONS
Menu Setting
Before starting recording and playback, it is necessary to set the mode for each operation using the MULTI JOG knob on
the front panel (MENU and +/– on the remote).
1.
While this unit is in the stop mode, press and
rotate the MULTI JOG knob (MENU and +/– on
the remote) to display the items in the menu.
* To select single disc play or relay play of 2 discs.
* To select an automatic start or manual start of
playback when the power is turned on.
* To select normal (x1) or double (x2) speed when
copying from disc tray A to disc tray B.
* To set the fade-in and fade-out time respectively for
recording.
* To select analog recording when digital recording is
not possible for SCMS using the DIRECT copy
function.
When editing CD TEXT
Play Mode
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Auto Play
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Copy Speed
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
FadeIn Time
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
SCMS Mode
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Track Name
CD–R
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Disc Name
CD–R
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
2.
Press the MULTI JOG knob to select the item to
be set. The options (shown underlined below)
blink and alternate as the knob is rotated.
Select the one to be set by pressing the MULTI
JOG knob again.
Play˚ SINGLE
Play˚ RELAY
Auto˚ ON
Auto˚ OFF
Copy˚ x1
Copy˚ x2
Fade˚ In˚ 1s10s
Can't˚ Copy
ANALOG˚ Copy
These settings remain even when the power is turned off.
FadeOutTime
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
* Enter alphabetical letters, numbers, and symbols.
See page 19 for details.
FadeOut˚ 1s10s
E-12
RECORDING TO A DISC .......................................................
Basic Recording Operation
Recording is done on disc tray B of this unit. Disc tray A is
used for playback only. Recording operation is described
with buttons on this unit and the remote control. These
button names are noted in the order of “button name
(remote control button name)”.
To load a disc
1.
Press POWER on the front panel to turn on the
power.
2.
Press v for disc tray B on your right (OPEN/
CLOSE B on the remote) to open the disc tray.
3.
Load a disc to be used for recording, correctly
aligned in the recessed area of the disc tray with
its recordable side facing down.
When loading an 8 cm (3 in.) disc, place it in the inner
recessed area of the disc tray. Do not put a normal 12
cm (5 in.) disc on top of an 8 cm disc.
4.
Press v (OPEN/CLOSE B on the remote) to
close the disc tray.
Note
You can also close the disc tray by pressing the front edge of
the disc tray gently.
When a new disc is loaded in this unit, this unit performs a
number of internal operations to determine the format and
content of the disc. During this time, “Reading” appears in
the display. This process requires approximately 10
seconds to complete for any type of disc.
When a CD-R disc without finalization performed or a CD-
RW disc is loaded in this unit, OPC (Optimum Power
Calibration) is automatically performed to make an optimal
recording. OPC optimizes the laser power to the reflectivity
of the disc.
During OPC, “OPC Adjust” appears in the display. This
process requires approximately 15 seconds for a CD-R and
45 seconds for a CD-RW to complete.
Note
OPC data is memorized both in this unit and the disc. This unit
can memorize the OPC data for up to 24 discs. After 24 discs
are reached, the oldest OPC data will be deleted and the newest
one will be added.
OPC process will not be performed on the disc if its OPC data
has been already in this unit’s memory. (When Disc Erase is
performed on a CD-RW disc, its OPC data will be also erased.)
After the disc has been read and any necessary internal
adjustments have been performed, one of the following
displays appears, and normal operation is possible.
When a prerecorded audio CD is loaded in this unit
When a new CD-R or CD-RW disc is loaded in this unit
NATURAL SOUND CD RECORDER CDR–D651
POWER
DISC A DISC B
DISPLAY A TEXT
/
TIME DISPLAY B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
PHONES LEVEL
MIN MAX
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
1 2,4 3
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
DISPLAY
OPEN
/
CLOSE
B
2,
4
Reading
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
1:
CD
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
0:
CD–R
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
OPC Adjust
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
RECORDING
E-13
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
........................................................RECORDING TO A DISC
To start recording
1.
Press REC.
This unit enters the record pause mode.
2.
Select the appropriate input signal to be used
for recording by pressing the INPUT button.
(See page 14 for details.)
3.
Adjust the recording level.
(See page15 for details.)
The recording level can be adjusted when making
digital and analog recordings. However the recording
level cannot be changed when making a CD DIRECT
copy.
4.
Press w/d (w on the remote) to start recording.
5.
Start playing the source.
6.
Press w/d (d on the remote) to pause recording
temporarily.
“Standby” lights in the display.
7.
To resume recording, press w/d (w or d on the
remote).
8.
Press a to stop recording.
“Wait” lights in the display while information is being
written to the PMA (Program Memory Area).
9.
Finalize the disc when recording is complete.
See page 21 for the finalization procedure.
10.
Press v (OPEN/CLOSE B on the remote) to
open the disc tray and remove the disc.
11.
Press v (OPEN/CLOSE B on the remote) again
to close the tray.
12.
Press POWER to turn off the power when you
have finished using this unit.
NATURAL SOUND CD RECORDER CDR–D651
POWER
DISC A DISC B
DISPLAY A TEXT
/
TIME DISPLAY B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
PHONES LEVEL
MIN MAX
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
12 10,11 29
14,6,7
8
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
TIME TEXT DIMMER
0
SPACE
+10
SYMBOL
PROG
DISPLAY
A
/
B
INPUT
OPEN
/
CLOSE
B
REPEAT RANDOM
CLEAR
MENU
EDIT DELETE SET
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQR
7
STU
8
VWX
9
YZ
A B
4,7
8
6,7
10,11
1
9
2
Standby
CD–R
REC
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
Important
Do not turn off the power during recording. If the
power is turned off, recorded material may be lost or
the disc may not perform normally.
If the power is turned off while recording on a CD-R
disc, any material recorded before the information is
written to the PMA (Program Memory Area) will be lost
and further recording on that disc will not be
possible.
During recording, make sure that this unit is not
subjected to shock or vibration as it may cause skips
or jumps to be included in the recording.
E-14
RECORDING TO A DISC .......................................................
Selecting an Input Source
Press INPUT to select the appropriate input source to be
used for recording among optical digital recording, analog
recording, and copying from disc tray A.
To record a digital source, press INPUT to light
DIGITAL.
To record an analog source, press INPUT to light
ANALOG.
To record a source CD placed on the disc tray A, press
INPUT to light DISC A. A CD placed on the disc tray A
can be recorded to a CD-R or CD-RW disc.
The copy speed can be selected at either normal speed
(as you listen) or double speed (takes half of the time of
normal speed recording).
When CD DIRECT copy is selected, DISC A
automatically lights.
Regardless of the INPUT setting, both digital and analog
signals are output at the same time.
When DIGITAL or DISC A is selected using INPUT, the
input digital sampling frequency is indicated in the
display.
Make this input source selection while this unit is in the
stop or record pause mode.
Selecting a Recording Mode
This unit features a number of recording modes. Select the
appropriate mode that suits your purpose.
CD DIRECT copy
A source CD placed on the disc tray A can be directly
recorded to a CD-R or CD-RW disc placed on the disc tray
B.
Single track synchronized recording
This unit automatically starts recording a single track when
the source component starts playback. This mode is
convenient for recording a mix of single tracks from
different sources.
All track synchronized recording
This unit automatically starts recording all tracks when the
source component starts playback. Track numbers are
automatically placed between the tracks being recorded.
Full AUTO synchronized recording
This mode automatically finalizes the disc after all track
synchronized recording. A CD-R disc can then be played
on a standard CD player.
A
CK NO.
R
ASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
Manual recording
In this recording mode, all recording operations (such as
starting, stopping, track marking, and finalization) are
manually performed.
When recording onto a partially recorded
disc
If a CD-R or CD-RW disc has some recording time
remaining on it before finalization is performed, any of the
recording modes can be normally performed. Recording
automatically starts from the location immediately after the
last recorded track on the disc.
In the following cases recording is NOT
possible
When the CD indicator is lit indicating that a CD or
finalized CD-R disc is loaded in this unit.
When the CD-RW and TOC indicators are lit indicating
that a finalized CD-RW disc is loaded in this unit.
When there is no recording time remaining on the disc
and “Disc Full” appears in the display.
When 99 tracks have been recorded and “Track Full”
appears in the display. Only 99 tracks may be recorded
on a CD.
When the CD-R or CD-RW disc loaded in this unit is not
intended for recording audio and “Not Audio” appears in
the display.
Before CD-R discs can be played on standard
CD players – Finalization
When you have finished recording on a CD-R disc, it is
necessary to finalize the disc to make it compatible with
standard CD players. If this procedure is not performed, the
CD-R disc will not be playable on a standard CD player.
If Full AUTO synchronized recording or CD DIRECT
copying is performed, finalization is automatically
performed following the conclusion of recording.
E-15
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
....................................................... RECORDING TO A DISC
Setting the Recording Level
There are two knobs used for setting the recording level
depending on the input source. When ANALOG is selected
using INPUT, the ANALOG REC LEVEL knob is used for
setting. When DIGITAL or DISC A is selected, it is not
normally necessary to set the recording level. However it is
possible to lower the recording level using the DIGITAL
REC LEVEL knob.
Analog recording
1.
Press REC to set this unit to the record pause
mode.
2.
Play the loudest passage of the source to be
recorded.
3.
Set the recording level using the ANALOG REC
LEVEL knob.
Adjust the recording level so that the OVER indicator
does not light at the loudest sound levels.
Digital recording
The digital recording level is set by default to 0dB, the level
of the input source. Normally, it is not necessary to adjust
the recording level.
However, it is possible to lower the recording level between
0 and –64dB if necessary.
The recording level can be adjusted by 1dB steps using the
DIGITAL REC LEVEL knob (MULTI JOG knob) (+/– on the
remote), while this unit is in the record or record pause
mode.
Manual Track Marking
This unit can automatically place track markers. However
you can also manually place track markers as you like
anywhere in your recording.
While recording, press TRACK NO. (TRACK NO. WRITE
on the remote).
A new track number is added at the location on the disc
corresponding to the time TRACK NO. (TRACK NO.
WRITE on the remote) is pressed.
Tracks cannot be shorter than 4 seconds, and a disc
cannot contain more than 99 tracks. Even if there is time
remaining on the disc, further recording is impossible
once 99 tracks have been recorded.
Notes
Manual track marking is recommended for the following:
* When an analog source is being recorded that contains a
section or numerous sections with levels too low to be
detected on the level meter.
* When recording digital satellite broadcasts
Manual track marking is possible even during synchronized
recording only if it is not digital recording from an external
unit.
DISC
B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
MULTI JOG
ANALOG REC LEVEL
REC
Standby
CD–R
REC
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
ANALOG REC LEVEL
MIN MAX
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
CD DIRECT copy
The recording level cannot be changed when the CD
DIRECT function is on.
DISC B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
TIME TEXT DIMMER
DISPLAY
A
/
B
INPUT
MENU
EDIT DELETE SET
DIGITAL REC
LEVEL knob
+/– buttons
DISC
B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
TRACK NO.
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
OPEN
/
CLOSE
B
TRACK NO. WRITE
E-16
RECORDING FUNCTIONS .....................................................
CD DIRECT Copy
This unit has a CD DIRECT copy function using both disc
trays. It digitally copies an entire source CD placed on disc
tray A onto a disc placed on disc tray B to be used for
copying.
When making a CD DIRECT copy, the copy speed can be
selected at either normal or double speed. However the
recording level cannot be changed when making a CD
DIRECT copy.
1.
Load a source CD on disc tray A and a disc to be
used for copying on disc tray B. Press v (OPEN/
CLOSE on the remote) to close the trays.
Make sure that the recordable time on the disc to be
used for recording is longer than the total play time on
the source CD.
2.
Press and rotate the MULTI JOG knob on the
front panel (MENU and +/– on the remote) to
select “Copy Speed” in the set menu shown in the
display. Then press the MULTI JOG knob (MENU
on the remote) again.
3.
Copy speeds of “x1” and “x2” appear blinking
alternately in the display as the MULTI JOG knob
(+/– on the remote) is rotated. Select the desired
copy speed by pressing the knob (+/– on the
remote).
4.
After the copy speed is set, press COPY to start a
CD DIRECT copy.
When making a CD DIRECT copy with the
synchronized recording mode described in the
next section, press REC MODE to select the
synchronized recording mode and press COPY.
When copying is complete, finalization automatically
starts and the disc can then be played on a standard
CD player. However, finalization is not performed when
doing single or all track synchronized recording.
Notes
While making a CD DIRECT copy at double speed, the analog
signal can be heard but the digital signal can not.
Never turn off the power or pull out the plug out from the wall
outlet during a CD DIRECT copy.
A disc copied from a source CD cannot be copied to another
disc.
See page 28 for Serial Copy Management System (SCMS)
standards.
If a disc cannot be digitally copied, analog copy is possible. To
make an analog copy, set the “SCMS Mode” to “ANALOG“ in the
menu settings. (See page 11 for details.)
Synchronized Recording
This function automatically starts recording when an audio
signal is detected. Therefore, recording starts at the same
time the source CD starts playback. There are three ways of
doing synchronized recording as follows:
Single track synchronized recording
This mode is convenient for recording a mix of tracks from
different sources. A new track marker is automatically
placed at the start of each track.
1.
Load a disc to be used for recording.
Use a disc containing enough space for recording a
source CD.
2.
Press REC to set this unit to the record pause
mode.
3.
Select the appropriate input source to be used for
recording by using INPUT on the front panel.
4.
Adjust the recording level. (See page 15.)
5.
Make sure that the source component is in the
stop mode.
6.
Press REC MODE.
The SINGLE and SYNCHRO indicators light in the
display.
7.
Start playing the source.
This unit automatically starts recording.
When playback of the current track is over (digital
recording), or this unit has recorded 4 seconds of
continuous silence as a track separation (analog
recording), recording ends. Then this unit enters the
record pause mode and synchronized recording
mode is canceled.
8.
Repeat steps
5
,
6
and
7
to record another
track.
9.
Press a when all recording is complete.
Disc information is being written to the PMA (Program
Memory Area).
When all recording is complete, perform finalization. (See
page 21 for the finalization procedure.)
Copy x2
CD–R
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
DISC
B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
REC MODE INPUT
REC
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
OPEN
/
CLOSE
B
REC
REC MODE
2 1:41
CD–R
44.I
REC
SINGLE
SYNCHRO
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
E-17
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
......................................................RECORDING FUNCTIONS
All track synchronized recording
This mode is convenient for recording all of the material
from a single audio source such as an MD, cassette tape,
or LP. Track markers are automatically placed between the
tracks being recorded.
1-5.
Repeat the steps described in the previous
section “Single track synchronized recording”.
6.
Press REC MODE twice.
ALL and SYNCHRO indicators light in the display.
7.
Start playing the source.
This unit automatically starts recording.
When making a digital recording, a new track
marker is placed each time a new track begins on
the source component.
When making an analog recording, spaces of
silence are interpreted as track separations, and a
new track marker is placed when a new audio
signal is detected. The silence should be about 4
seconds long.
8.
Once this unit has recorded 20 seconds of
continuous silence, recording ends and “Wait”
lights in the display while the disc information is
being written to the PMA.
After this writing is complete, this unit enters the stop
mode.
When all recording is complete, perform finalization. (See
page 21 for the finalization procedure.)
Notes
Track numbers may not be correctly recorded depending on the
source component. In this case, perform track marking
manually.
If the recording source has excessive noise or contains a lot of
low level sound, track marking may not be properly performed
without the silence being recognized. In this case, perform track
marking manually.
If the sampling frequency changes while making digital
recordings from an external unit, this unit may fail to perform
synchronized recording normally.
Full AUTO synchronized recording with
finalization
This mode automatically performs finalization after all
synchronized recording is complete.
(See page 21 for the finalization procedure.)
1-5.
Repeat the steps described in the section
“Single track synchronized recording”.
6.
Press REC MODE three times.
AUTO and SYNCHRO indicators light in the display.
7.
Start playing the source.
This unit automatically starts recording.
8.
Once this unit has recorded 20 seconds of
continuous silence, recording ends and “Wait”
lights in the display while the disc information is
being written to the PMA.
9.
Finalization automatically starts after this writing
is complete.
Press a to cancel finalization before the 20 seconds
of continuous silence is reached.
Once finalization is started, operation buttons do not
work.
Never turn off the power during finalization.
Recording stops while the source is being played if
there is no more recordable space on a disc, or 99
tracks have been already recorded. In this case,
perform finalization manually.
Note
When making a synchronized recording after DISC A is selected
using INPUT, track marking and ending are all performed based
on the CD placed on disc tray A. Also recording can be done at
double speed if necessary by changing the copy speed in the
menu settings when DISC A is selected.
2 1:41
CD–R
44.I
REC
ALL SYNCHRO
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
2 1:41
CD–R
44.I
REC
AUTO
SYNCHRO
L
dB
R
–60 –30 –I0 –6 –4 –2 –I 0
OVER
E-18
RECORDING FUNCTIONS .....................................................
Track and Disc Erase
(CD-RW discs only)
CD-RW discs can be erased and new recordings can be
made after material has been erased. The following 4 types
of erasing are possible with this unit.
Last Track Erase
This operation erases the last track. Last Track Erase
cannot be done if a CD-RW disc has been finalized or only
one track has been recorded on the disc.
1.
Load a CD-RW disc that has been recorded on.
This operation is not possible on a finalized CD-RW
disc.
2.
Press ERASE.
“Erase LAST?” appears in the display.
Proceed to the next step when erasing only the last
track. To erase other tracks as well, select the track
number from which you wish to start erasing by
rotating the MULTI JOG knob counterclockwise.
To cancel the Erase mode, press a.
3.
Press w/d (w on the remote) to start Last Track
Erase.
This operation requires from several seconds up to
a few minutes to complete.
During Last Track Erase, “Erasing” appears in the
display, and the approximate amount of elapsed
time is displayed.
4.
This unit enters the stop mode when erase is
complete.
All Track Erase
This operation erases all of the tracks. All Track Erase
cannot be done if a CD-RW disc has been finalized.
1.
Load a CD-RW disc that has been recorded on.
This operation is not possible on a finalized CD-RW
disc.
2.
Press ERASE until “Erase ALL?” appears in the
display.
To cancel the Erase mode, press a.
3.
Press w/d (w on the remote) to start All Track
Erase.
This operation requires approximately 80 seconds.
During All Track Erase, “Erasing” appears in the
display, and the approximate amount of elapsed
time is displayed.
4.
This unit enters the stop mode when erase is
complete.
TOC Erase
TOC erase is only available on a CD-RW disc that has been
finalized. After the TOC is erased, the effects of finalization
are defeated, and further recording is possible.
1.
Load a CD-RW disc that has been finalized.
2.
Press ERASE.
“Erase TOC?” appears in the display.
To cancel the Erase mode, press a.
3.
Press w/d (w on the remote) to start TOC Erase.
This operation requires approximately 80 seconds
to complete.
During TOC Erase, “Erasing” appears in the display,
and the approximate amount of elapsed time is
displayed.
4.
This unit enters the stop mode.
Notes
When TOC Erase is complete, the TOC indicator turns off.
When CD TEXT is recorded on a CD-RW disc, the TOC indicator
blinks in the display. To save this data, perform finalization.
Disc Erase
This operation deletes all data on the disc. It is usually not
necessary to perform this function, however, it may be used
to recover a disc.
1.
Load a CD-RW disc that has been recorded on.
This operation is possible on both finalized and
underlined discs.
2.
Press and hold ERASE for about 2 seconds.
“Erase DISC?”appears in the display.
To cancel the Erase mode, press a.
3.
Press w/d (w on the remote) to start Disc Erase.
This operation requires approximately a half of the
total recordable time on the disc.
4.
The disc tray opens when Disc Erase is complete.
Notes
When there is only one track recorded on a CD-RW disc that has
not been finalized, only All Track Erase is possible.
Do not turn off the power during the erase operation as it could
cause this unit to malfunction and make the disc unusable.
If the message “Check Disc” appears in the display during an
erase operation and erasing stops, the disc may be damaged.
In this case, inspect the disc and then try erasing it again.
E-19
GETTING STARTED
PLAYBACKRECORDING
ADDITIONAL
INFORMATION
ENGLISH
......................................................RECORDING FUNCTIONS
REC Mute
Press REC MUTE to create a blank space at the end of
recording. A 4-second blank space is recorded, and this
unit enters the record pause mode. To create a blank space
longer than 4 seconds, press and hold REC MUTE.
When REC MUTE is released, this unit enters the record
pause mode. During the REC MUTE operation, the REC
indicator blinks.
DISC
B
Recordable
ReWritable
COPY
REC MODE TRACK NO.
FINALIZE ERASE
INPUT
MULTI JOG
DIGITAL REC LEVEL
DISC A DIGITAL ANALOG
PUSH MODE
ANALOG REC LEVEL
MINFADE IN
/
OUT MAX
REC MUTE
REC
REC MUTE
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
TIME TEXT DIMMER
DISPLAY
A
/
B
INPUT
OPEN
/
CLOSE
B
REC MUTE
Fade In/Fade Out Function
This unit has a fade-in function to gradually rise the
recording level at the start of recording and a fade-out
function to gradually lower the recording level at the end of
recording.
Fade In
While this unit is in the record pause mode, press REC to
start a recording with a fade-in. During this recording, the
REC indicator blinks in the display.
Fade-in lasts about 3 seconds. However it is possible to
adjust the fade-in time between 1 and 10 seconds in the
menu settings.
Fade Out
Press REC during recording to end the recording with a
fade-out. This unit enters the record pause mode when
fade-out recording is complete. Fade-out time can also be
adjusted in the menu settings.
To change the fade-in and fade-out time
1.
While this unit is in the record or stop mode,
press and rotate the MULTI JOG knob (MENU
and +/– on the remote) to select “FadeIn time” or
“FadeOutTime” in the set menu.
2.
Press the knob (MENU on the remote) again and
rotate the knob (+/– on the remote) to set the
desired time between 1 and 10 seconds.
3.
Press the MULTI JOG knob (MENU on the
remote) again to enter the time setting. This
setting remains even when the power is turned
off.
CD TEXT Copying and Editing
This unit is CD TEXT compatible. When digitally recording a
disc with CD TEXT data, the data is automatically recorded
onto the disc loaded on the disc tray B. It is also possible to
edit CD TEXT data on the newly recorded disc.
CD TEXT copying
CD TEXT data is automatically copied as the source CD is
recorded, when recording a source CD with CD TEXT data
(23 characters maximum) placed on the disc tray A onto a
disc placed on the disc tray B with DISC A selected using
INPUT, or with the CD DIRECT copy function. To save the
CD TEXT data on the disc, perform finalization. CD TEXT
data is displayed by pressing TEXT/TIME on the front panel
(TEXT on the remote). See page 10 for details.
CD TEXT copying cannot be made when doing manual
recording.
DISPLAY A TEXT
/
TIME DISPLAY B
PHONES LEVEL
MIN MAX
TEXT/TIME
COPY
A
FADE IN
/
OUT
REC
REC MUTE
TRACK NO.
WRITE
REC MODE
FINALIZE ERASE
TIME TEXT DIMMER
DISPLAY
A
/
B
INPUT
OPEN
/
CLOSE
B
TEXT
Note
Some CD TEXT data cannot be copied if they are protected by
copyright.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219

Yamaha CDR-D651 El kitabı

Kategori
CD çalar
Tip
El kitabı