Panasonic ET-ELW20 Operating Instructions Manual
- Kategori
- Projeksiyon lensleri
- Tip
- Operating Instructions Manual
ENGLISH
FRANÇAIS
日本語
Commercial Use
Model No.
ET-ELW21
ET-ELW20
ET-ELT22
ET-ELT23
TQZJ444-4
Projection Lens
Operating Instructions
Thank you for purchasing this Panasonic product.
■
To ensure correct use of this lens, please read the operating instructions supplied
with the lens and the projector carefully.
■
Before using this product, be sure to read “Read this rst!” (
Page 3).
■
Please save this manual for future use.
ET-ELW21
ET-ELT22
ET-ELW20
ET-ELT23
Read before use
This document is intended for the various projection lenses that can be attached to
and used in conjunction with Panasonic projectors.
For Model No. and model names, refer to the product list (
Page 4).
2-ENGLISH
Read this rst! ......................................................................................3
Before Use.............................................................................................4
Attaching / removing the projection lens ...........................................4
Before replacing the projection lens ........................................................ 4
Attaching the Lens / Detaching the Lens................................................. 5
Making Adjustments ............................................................................5
Correcting the Focus ............................................................................... 5
Projection relationships.......................................................................7
Lens shift ranges ..................................................................................8
Specications .....................................................................................10
Dimensions .........................................................................................10
Projected image size and Projection distance.......Appendix / Annexe /
付録
1
The "Appendix" can be found after the Japanese language section (
日本語
).
█ Contents
ENGLISH-3
Read this rst!
Always follow these precautions
WARNING:
Do not look at or place your skin into the light emitted from the lens while the
projector is being used.
Doing so can cause burns or loss of sight.
z
Strong light is emitted from the projector’s lens. Do not look at or place your hands
directly into this light.
z
Turn off the power when moving away from the projection lens or projector.
Do not project an image with the lens cover attached.
z
Doing so can cause re.
Do not allow children to reach the spacer.
z
The spacers can cause personal injury if swallowed.
z
If the spacers are swallowed, seek medical advice immediately.
CAUTION:
Before replacing the projection lens, be sure to turn off the power and
disconnect the power plug from the wall outlet.
z
Unexpected projection of light may cause injury to eyes.
z
Replacing the projection lens without removing the power plug may result in electric
shock.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
z
Strong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used.
Doing so can cause re, damage to the object, or malfunction of the lens and
projector.
z
Strong light is emitted from the projector’s lens.
Do not open the desiccant bag. Do not eat the contents.
Inadvertently ingesting desiccant could be harmful.
z
If the desiccant gets into your eyes or mouth, immediately rinse with plenty of water
and seek medical attention.
z
Keep desiccant out of the reach of children.
4-ENGLISH
■
Product list
The product names and model numbers of the projection lenses covered by this manual
are as follows.
Product name Model number
Fixed focus lens ET-ELW21
Zoom lens ET-ELW20 / ET-ELT22 / ET-ELT23
■
Supported projectors
PT-MZ770 / PT-MW730 / PT-MZ670 / PT-MW630 / PT-MZ570 / PT-MW530 / PT-EZ770 /
PT-EW730 / PT-EX800
Note
z
This manual omits the alphabets at the end of projector model numbers.
z
Models other than the above may also be supported. Refer to the operating instructions of
the projector you are using.
■
Supplied Accessories
Make sure that the following has been provided.
Part name Appearance
Lens cover
1 each for front and rear
Spacer
(T0SAS0001--)
(Colors: black, cream, clear)
4 each
z
The product is delivered with a
lens cap attached.
z
The shape and size of the lens
caps are different for each product.
Before replacing the projection lens
Return the projection lens to the home position before replacing or removing it.
For details on how to return the lens to the home position, refer to the operating
instructions of the projector.
Attention
z
Make sure that the projector power supply is switched off before attaching or detaching the
projection lens.
z
After removing the projection lens, store it safely away from vibration or impacts.
z
Do not touch the electric contact points of the projection lens with your fingers. Dust and dirt
on the contacts may cause contact malfunctions, while static electricity may damage the unit.
Attaching / removing the projection lens
Before Use
ENGLISH-5
Attaching / removing the projection lens (continued)
Making Adjustments
Correcting the Focus
When the projection lens is attached to the projector and images are being projected
onto the screen, the peripheral focus may be out of focus in some localized areas.
In such cases, use the supplied spacers to correct the focus of these areas, and perform
adjustments so that the entire image is even.
■
Relationship between lens orientation and screen focus
If the projection lens is tilted with respect to the plane of the screen, uneven focus will
result. For example, when the front side of the lens (screen side) is tilted downward as
shown in the figure below (direction of the dotted arrow), the upper part of the screen
will be tilted backward and the lower part of the screen will be tilted forward.
Projection lens
Image formation surface
Screen surface versus focal point
■
Procedure for correcting the focus
Attention
z
Turn off the projector before removing the projection lens.
Note
z
Focus correction requires some technical skill. Be sure to have a person with knowledge of
projectors or a service technician to perform adjustments.
z
Do not touch the surface of the lens with bare hands. Finger prints and dirt on the surface
of the lens will be magnified by the lens and lower the quality of the projected image. Place
the supplied lens cover on the zoom lens when the projector is not in use.
z
The lens is made of glass. The lens could be damaged if brought into contact with or
rubbed against hard objects. Handle the lens carefully.
z
Use a clean, soft and dry cloth to wipe away dust and dirt from the projection lens.
Do not use fl uffy cloths containing oil, water or dust for cleaning. The lens is easily
damaged, so do not apply excessive pressure when wiping it.
Attaching the Lens / Detaching the Lens
For details on attaching or removing the projection lens, refer to the operating
instructions for the projector.
6-ENGLISH
Making Adjustments (continued)
D
C
A
B
Fig. 1
AA
投写レンズ
ネジ
スペーサー
レンズマウンター
D
D
B
C
Fig. 2
Screws
Projection lens
Lens mounter
Spacers
1) Install the projector in the installation location, and turn it on to project an image.
2) Move the lens to its home position.
3) Operate the projector to shift the focus of the entire projected image toward
the front of the screen.
4) Operate the projector to shift the focus toward the screen a little bit at a time until
one of the areas A to D in Fig. 1 just comes into focus on the screen, and then stop.
z
In this state, the “just focus points” of the unfocused areas are positioned just in front of
the screen. The distance between this position and the screen is the correction distance.
5) Insert the spacers between the body of the projector and the lens mounter, as
shown in Fig. 2.
z
Remove the lens mounter from the projector, and insert the spacers in the positions
that correspond to the unfocused areas.
z
The “just focus points” of the areas for which you inserted spacers will be corrected
toward the rear of the screen.
z
Make sure the adhesive surfaces of the spacers face the lens mounter when inserting them.
z
The correction distance is determined by the thickness and quantity of spacers
inserted. Insert spacers according to the correction distance.
(The unit for correction distances derived from the formulas in the following table is millimeters.)
Spacer Color Thickness
Correction distance
during projected image size SD (m)
Clear 0.1 mm SD × SD × 51.5
Black
0.2 mm SD × SD × 103
Cream
0.3 mm SD × SD × 154.5
Correction distance guide: When the projected image size is 1.52 m (60 in.), the cor-
rected distance when one 0.1 mm thick spacer is inserted is 120 mm.
Attention
z
Installing the lens mounter, be careful not to put wiring between the lens mounter and the
projector unit.
ENGLISH-7
Projection relationships
The dimensional relationship between the screen and the projector is shown below.
■
Dimensional relationship diagram
L (LW/LT)
L (LW/LT)
SW SH
H
SH
SW
SD
L1
L1
Screen
Projected image
Note
z
This diagram assumes that the size and position of the projected image will be adjusted so
that the image fills the entire screen.
z
This illustration is not drawn to scale.
L Projection distance
LW Minimum distance
LT Maximum distance
L1 Lens protrusion dimension
SH Image height
H Distance from the lens center to the lower edge of the
projected image
SW Image width
SD Projected image size
z
L1 dimensions (approximate values) (Unit: m)
Projector model ET-ELW21 ET-ELW20 ET-ELT22 ET-ELT23
PT-MZ770 / PT-MW730 / PT-MZ670 /
PT-MW630 / PT-MZ570 / PT-MW530
0.005 0.035 0.036 0.032
PT-EZ770 / PT-EW730 / PT-EX800 0.050 0.080 0.081 0.080
Note
z
The illustrations of projectors in this manual are for informational purposes only and do not
represent a specific projector model. Configurations may vary with the model.
8-ENGLISH
Projection relationships (continued)
Attention
z
To prevent blocking of the intake and exhaust vents, maintain clearances from walls and
objects of at least 1 000 mm (3'3") for the exhaust vent and at least 500 mm (1'8") for the
intake vent.
z
Avoid setting up in places which are subject to sudden temperature changes, such as near
an air conditioner or lighting equipment (studio lamps, etc.).
■
Dimensional relationship
For details on the projection distance (L), refer to “Projected image size and Projection
distance” and “Projection distance formulas” in the Appendix.
Note
z
For details on “Projected image size and Projection distance” for projector models other
than PT-MZ770 / PT-MW730 / PT-MZ670 / PT-MW630 / PT-MZ570 / PT-MW530 /
PT-EZ770 / PT-EW730 / PT-EX800, refer to “Setting up” in the operating instructions of the
projector.
Perform the lens position shift within the adjustment range.
Perform lens shift adjustment within the ranges shown in the following illustrations.
Moving the lens outside of the adjustment ranges may alter the focus. The focus may
change when the lens position is shifted out of the adjustment range. This is because
the movement of the lens is restricted to protect the optical parts. Projection position
can be adjusted with the optical axis shift based on the home position in the respective
range.
Lens model ET-ELW20 / ET-ELT22 / ET-ELT23
PT-MZ770 / PT-MW730 / PT-MZ670 /
PT-MW630 / PT-MZ570 / PT-MW530
Image width H
Standard projection position
Image height V
0.35 H
0.30 H 0.30 H
0.35 H
0.67 V
0.67 V
0.19 V0.19 V
Lens shift ranges
ENGLISH-9
Lens shift ranges (continued)
Lens model ET-ELW20 / ET-ELT22 / ET-ELT23
PT-EZ770 / PT-EW730
0.6 V
Image width H
0.1 H0.1 H
Image height V
0.6 V
Standard projection position
PT-EX800
0.5 V
Image width H
0.1 H0.1 H
Image height V
0.5 V
Standard projection position
Note
z
Lens shifting cannot be performed when a fixed-focus lens (model no.: ET-ELW21) is
attached.
z
The home position of the projector a point of origin position for the lens shift (i.e., vertical
and horizontal positions of the lens) based on the results of lens calibration. It is not the
optical center position of the screen.
10-ENGLISH
Dimensions
(Unit: mm)
Model number Dimensions
ET-ELW21
166 (6-17/32")
φ108 (4-1/4")
φ102 (4-1/32")
Specications
Check the specifications of each projection lens, and use the appropriate lens for your
intended use.
Model No. ET-ELW21 ET-ELW20 ET-ELT22 ET-ELT23
Lens Type Short fixed lens Short zoom lens Long zoom lens
Ultra long
zoom lens
F value 2.0 1.8 to 2.3 1.8 to 2.3 1.8 to 2.3
Focal Length (f) 13.05 mm 20.4 to 27.6 mm 45.6 to 73.8 mm 73.9 to 117.1 mm
Dimensions
*1
Width 108 mm (4-1/4") 116 mm (4-9/16") 108 mm (4-1/4") 108 mm (4-1/4")
Height 108 mm (4-1/4") 116 mm (4-9/16") 108 mm (4-1/4") 108 mm (4-1/4")
Depth 166 mm (6-17/32") 196 mm (7-23/32") 197 mm (7-3/4") 196 mm (7-23/32")
Net Weight 1.08 k
]
(2.38 lbs) 1.20 k
]
(2.65 lbs) 1.18 k
]
(2.60 lbs) 1.20 k
]
(2.65 lbs)
*1: Excluding protrusions.
ENGLISH-11
Dimensions (continued)
Model number Dimensions
ET-ELW20
196 (7-23/32"; fully extended)
φ116 (6-17/32")
ET-ELT22
197 (7-24/32"; fully extended)
φ108 (4-1/4")
φ88.5 (3-15/32")
ET-ELT23
196 (7-23/32"; fully extended)
φ108 (4-1/4")
φ88.5 (3-15/32")
Panasonic System Solutions Company of North America
Two Riverfront Plaza, Newark, NJ 07102
TEL: (877) 803 - 8492
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
TEL: (905) 624 - 5010
Panasonic Corporation
Web Site : https://panasonic.net/cns/projector/
© Panasonic Corporation 2018
HS0412AM4078 -PS
Printed in Japan
Disposal of Old Equipment
Only for European Union and countries with recycling systems
This symbol on the products, packaging, and/or accompanying documents means that
used electrical and electronic products must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to
applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct
method of disposal.
Product Information (for Turkey only)
AEEE Yönetmeliğine Uygundur.
Eski Ekipman ve Bataryaların İşlenmesi.
Sadece geri dönüşüm sistemleri olan Avrupa Birliği ve ülkeleri için geçerlidir.
Ürünler, ambalaj ve/veya ekli belgeler üzerindeki bu semboller kullanılmış elektrik ve
elektronik ürünlerin genel ev atığı ile karıştırılmaması gerektiğini ifade eder.
Eski ürünlerin toplanması ve geri kazanılması için bu atıklar lütfen yasayla belirlenmiş olan
uygun toplama merkezlerine teslim ediniz.
Bu atıkların doğru işlenmesiyle, değerli kaynakların korunmasına ve insan sağlığı ve
çevreye olası negatif etkilerinin engellenmesine yardımcı olabilirsiniz.
Atıkların toplanması ve geri dönüşümü için detaylı bilgi için lütfen bağlı olduğunuz yerel
yönetimlerle iletişime geçiniz.
Atıkların atılmasıyla ilgili yanlış uygulamalar yasayla belirlenmiş olan cezalara sebebiyet
verebilir.
Information for users in the European Union
Importer’s name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Panasonic ET-ELW20 Operating Instructions Manual
- Kategori
- Projeksiyon lensleri
- Tip
- Operating Instructions Manual
diğer dillerde
- English: Panasonic ET-ELW20