Yamaha NS-C225 El kitabı

Yamaha
Marka
Yamaha
Model
NS-C225
Tip
El kitabı
DeutschFrançais EspañolEnglish
E-1
NS-C225
SPEAKER SYSTEM
Thank you for choosing a Yamaha speaker system.
Caution
■ Read the following before using these speakers:
• To assure the finest performance, please read
this manual carefully. Keep it in a safe place
for future reference.
• Install the speakers in a cool, dry, clean place
away from windows, heat sources, sources of
excessive vibration, dust, moisture and cold.
Avoid sources of humming (transformers,
motors). To prevent fire or electric shock, do
not expose the speakers to dripping or
splashing.
• To prevent the enclosure from warping or
discoloring, do not place the speakers where
they will be exposed to direct sunlight or
excessive humidity.
• Do not place the following objects on top of
the speakers:
1. Glass, china, etc.
If glass etc. falls by vibrations and breaks,
it may cause personal injury.
2. A burning candle etc.
If the candle falls by vibrations, it may
cause fire and personal injury.
3. A vessel with water in it
If the vessel falls by vibrations and water
spills, it may cause damage to the unit, and/
or you may get an electric shock.
• Do not place the speakers where foreign
objects such as water drips might fall. It might
cause a fire, damage to this unit, and/or
personal injury.
• Do not place the speakers where they are liable
to be knocked over or struck by falling objects.
Stable placement will also ensure better sound
performance.
• Secure placement or installation is the owner’s
responsibility. Yamaha shall not be liable for
any accident caused by improper placement or
installation of speakers.
• Any time you note distortion, reduce the
volume of your amplifier immediately. Make
sure the input power does not exceed the
specified maximum input power, otherwise the
speakers will be damaged.
• Do not attempt to clean the speakers with
chemical solvents as this might damage the
finish. Use a clean, dry cloth.
• Do not attempt to modify or fix the speakers.
Contact qualified Yamaha service personnel
when any service is needed. The cabinet
should never be opened for any reasons.
Note:
This speaker is magnetically shielded, but placing
them too close to a TV may impair the TV picture. If
this happens, move the speaker away from the TV.
Owner’s Manual
URG
E-2
Setting Up the Speaker
Place the speaker on the floor under the TV or
inside the TV rack so that it is stabilized.
■ Mounting the speaker NS-C225 on
the wall
The speaker can be mounted on a wall by using
the bracket attached to the speaker’s back panel.
Fasten screws into a firm wall or wall support as
shown in the figure below, and hang the holes on
the protruding screws.
When placing the speaker on top of the TV
To prevent the speaker from falling down, put the
provided fasteners at two points on both bottom
of the speaker and top of the TV.
Notes:
• Do not place the speaker on top of the TV whose
area is smaller than the bottom area of the speaker.
If placed, the speaker may drop out causing an
injury to you.
• Do not place the speaker on top of the TV with an
inclination.
• Do not touch the adhesive surface after peeling off
the seal as this will weaken its adhesive strength.
• Thoroughly wipe clean the surface where the
fastener is to be applied. Note that adhesive
strength is weakened if the surface is dirty, oily or
wet and that this may cause the center speaker to
drop.
12
Peel off
the seal
TV set
Fastener
NS-C225
WARNING:
• The speaker weights 2.8 kg (6.2 lbs). Do not
mount them on thin plywood or soft wall
surface material, as the screws may come out
of the flimsy surface, causing the speakers to
fall down and be damaged, or result in
personal injury.
• Do not fasten the speakers to wall with nails,
adhesives, or other unsound hardware. Long
term use and vibrations may cause them to fall
down.
• To avoid accidents resulting from tripping
over loose speaker cords, fix them to the wall.
Holes
Make sure that the screws are caught by a
narrow part of the holes securely.
320 mm
(12-5/8”)
NS-C225
Wall or wall
support
Tapping screw
(commercially
available)
Diam. 3.5 to
4 mm
(1/8”)
3 mm
(1/8”)
Min.
20 mm
(3/4”)
E-3
English
Connecting the Speaker
Always turn off your amplifier or receiver before making any connections.
■ Preparing Your Speaker Cables
Carefully remove 10 mm (3/8”)of insulation from
both ends of your speaker cables and twist the
bare wires tightly, as shown.
■ Hookup
■ Using a Banana Plug
1. Remove the speaker terminal cover by
gently pulling it toward you.
2. Tighten the terminal knob.
3. Simply insert the banana plug into the
terminal.
Notes:
• Make sure that the bare wires are not touching
each other as this could damage the speaker and
amplifier.
• Connect one speaker to the left terminals of your
amplifier, and another speaker to the right
terminals, making sure not to reverse the polarity
(+, –). If one speaker is connected with reversed
polarity, the sound will be unnatural and lack bass.
Good No Good
10 mm
(3/8”)
CENTER REAR
(SURROUND)
R
L
+
–
NS-C225
Amplifier or
receiver
+
–
Loosen
Tighten
1
3
2
Banana Plug
Removing the front cover
The front cover is attached to protect the speaker
unit, but you can remove it if necessary.
The front cover is fixed by magnets. Hold the
speaker with one hand, and pull the front cover
gently with the other to remove it.
Specifications
Type
.......... 2-way acoustic suspension speaker system
magnetic shielding type
Driver ................... 6.5 cm (2.6”) cone woofer x 4
3 cm (1”) dome tweeter
Impedance ...................................................... 6 Ω
Frequency Response ..................65 Hz to 50 kHz
Nominal Input Power ...................................40 W
Maximum Input Power ..............................120 W
Sensitivity................................... 86 dB/2.83 V/m
Crossover Frequency...................................3 kHz
Dimensions (W x H x D)
............. 440 (17.3”) x 94 (3.7”) x 133 (5.2”) mm
Weight ..........................................2.8 kg (6.2 lbs)
* Specifications are subject to change without
notice due to product improvements.
Notes:
• When removing the cover, be careful that you don’t
touch the drive units, and don’t exert excessive
force with any tools.
• There are magnets on the reverse side of the front
cover. Do not place the front cover close to objects
that might be affected by magnets, such as TVs,
clocks, magnetic cards, diskettes etc. after
removing it.
©2004 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Indonesia WD70580-1
This product mainly uses lead-free solder.
Cet appareil utilise principalement de la soudure sans plomb.
Dieses Produkt verwendet hauptsächlich bleifreies Lot.
Este producto utiliza principalmente soldadura sin plomo.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Yamaha NS-C225 El kitabı

Yamaha
Marka
Yamaha
Model
NS-C225
Tip
El kitabı
PDF İndir
rapor

Diğer dillerde

İlgili Makaleler