Samsung SCC-B2007P Kullanım kılavuzu

DAY/NIGHT COLOR CAMERA

SCC-B2303(P)/B2003P

SCC-B2307P/B2007P

User’s Manual

E

Tu

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 1

E

2

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE REAR

COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED

SERVICE PERSONNEL.

To prevent damage which may result in fire or electric shock hazard,

do not expose this appliance to rain or moisture.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference that may cause undesired

operation.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

This symbol indicates

high voltage is present

inside. It is dangerous to

make any kind of contact

with any inside part of

this product.

This symbol alerts you

that important literature

concerning operation and

maintenance has been

included with this

product.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 2

3

Important Safety Instructions

E

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, or other apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being from being walked on or

pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a used,

caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-

over.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or been dropped.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 3

E

4

Contents

Chapter 1 Introduction ........................................................ 5

Chapter 2 Special Features ............................................. 6

Chapter 3 Part Names and Functions ............................... 7

Chapter 4 Installation .......................................................... 12

Cautions for Installation and Use ....................... 13

Connecting Automatic Shutter Lens Connector

........... 14

Fixing Lens and Adjusting Lens Selection Switch

....... 15

Adjusting Back Focus ........................................ 16

Connecting Cables ............................................ 18

Chapter 5 Camera Set-Up ................................................. 20

Appendix Product Specification ........................................ 39

 NOTE: Avoid aiming the camera directly towards extremely bright

objects such as the sun, as this may damage the CCD image sensor.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 4

5

Chapter 1 Introduction

E

The DAY/NIGHT Camera operates in a color mode in an the

illumination over the standard value and otherwise in B/W mode by

deleting the IR Cut function, which contributes to the improvement

of sensitivity so that it is called a low illumination camera which is

able to identify objects in a dark area. Meanwhile, it has

incorporated a Sense Up function owing to a low speed shutter and

a field accumulation method to improve its low illumination feature

prominently.

The DAY/NIGHT Camera is mostly used in dark places like

basement parking lots with a comparatively low illumination. In

daytime, it provides a color screen of high density with a horizontal

resolution of 480, and, at night, it utilizes the DAY/NIGHT function

as well as the Sense Up function to identify objects. In same cases,

you may use this camera in relation to the infrared ray emission

equipment additionally.

[DAY/NIGHT]

It is a function of a color camera to delete the fiter with the

IR Cut function in an illumination below the standard value

so that it has a better sensitivity.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 5

6

Chapter 2 Special Features

E

High Sensitivity

It has an up-to-date 1/3" Super(EXview)-HAD IT CCD for an image of high

sensitivity.

Low Illumination Function

It has both a low illumination function and DAY/NIGHT function based on

digital signal technology in order to operate in the worst environment

without light.

Digital Zoom Function

It has a digital zoom function for a 10 time enlargement as a maximum. (If

you turn the PIP function to the Digital Zoom mode, the whole screen will

be displayed as a PIP screen.

Superior Back Light Adjustment Function

In case the object has a bright illumination or sunlight behind it, this camera

adjusts the image shaded by the back light for clear photographs.

Digital Power Supply Synchronization Method

The Full Digital Method Line Lock is realized in this camera, which adjusts

the vertical camera synchronization directly to improve controllability and

reliability of the camera.

Resolution

It realizes high resolution resulting from full digital image processing

supported by a state-of-art digital signal technology.

Output Signal Setting

It is able to reverse video output signals and set both a vertical and

horizontal profile.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 6

7

Chapter 3 Part Names and Functions

E

Side View

Mount Adapter Fixing Groove

This groove is used for screwing the mount adapter, a part of the bracket

where the camera will be installed.

Camera Lens(Option)

This lens is installed in the camera.

* A camera lens with a stained surface should be cleaned softly with a lens

tissue or ethanol painted cotton cloth.

Auto Iris Lens Connector

This connector provides the automatic shutter lens with power supply,

control signal, video signal, or DC signal necessary for the control of the

lens shutter

Automatic Shutter

Lens Control Cable

ALC Lens

Selection Switch

Auto Iris Lens

Connector

Mount Adapter Fixing

Groove

Back Focus

Control Bar

Camera Lens

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 7

E

8

Auto Iris Lens Control Cable

This cable transmits the control signal from the camera to control the lens

shutter.

Back Focus Control Bar

It controls the back focus.

ALC Lens Setting Switch

This switch sets the Auto Iris lens type for use.



DC : When you attach an Auto Iris lens requiring the DC control signal,

please put this switch in the DC position.



VIDEO : When you attach an Auto Iris lens requiring the video control

signal, please put this switch in the VIDEO position.

Rear View

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 8

E

9

① Power Display LED

When the camera is supplied with power, LED is on.

➁ Video Output Terminal

The monitor video input terminal is connected with this terminal through

which the camera video signal comes out.

➂ Remote Input Terminal(RS-232)

This terminal is used for camera control at the production plant.

1

2 3 4

1 TXD

2 RXD

3 +5V

4 GND

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 9

E

10

➃ DAY/NIGHT External Signal Input & Alarm Signal Output

This is a function to receive the external DAY/NIGHT signal from the

sensor(option) and convert the signal into BW. The MOTION DET

function generates an alarm signal when a movement is detected.

①

➁

DAY/NIGHT IN

GND

ALARM OUT

Connect an external sensor to the DAY/NIGHT terminal as shown in ① then

connect any external device such as a buzzer or lamp to the ALARM

terminal as shown in ➁.

The ALARM output terminal is an open collector with the following capacity:

DC 16V and 100mA.

OFF : Open contact

ON : Below 100mA

The DAY/NIGHT input terminal has the input of DC 5V pull-up and over

0.2mA.

OFF : Open contact

ON : Closed contact

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 10

E

11

⑤ Camera Operation Switch(Setup Switch)

The function of the camera operation switch changes depending on

whether the camera is currently in the usual operation mode(No setup

menu is seen on the screen) or the setup menu mode.

In the usual operation mode



[LEFT/RIGHT] key : Press key for about 2 seconds and the

menu comes out to control the DC IRIS level. The

[LEFT] key raises the level and the [RIGHT] key

lowers the level.



[ENTER] key : It is used to enter the Setup menu.(Press it about 2

seconds.)

In the setup menu mode



[UP/DOWN] key : These keys move up or down the cursor.



[LEFT/RIGHT] key : These keys move the cursor to the left or right or

identify the values sequentially which can be

assigned in each setup menu.



[ENTER] key : It is used to enter a sub-menu of a setup menu by

clicking the setup menu or to set the current value.

➅ Power Connection Port

This port is connected to the power(adapter) cable.

[LEFT/RIGHT] key

[ENTER] key

[UP/DOWN] key

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 11

12

Chapter 4 Installation

E

This chapter describes what should be checked before installation, how to

set the installation environment, and what should be done during

installation. Then, it describes how to install the camera and connect the

cable in actual circumstances.

Be sure to check if the following items are included in the package.

Before Installation

Checking the contents of the package

Camera Camera Holder(Mount)

C Mount Adapter Auto Iris

Lens Connector

User's Manual

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 12

E

13

① Do not disassemble the camera on your own.

➁ Be careful when handling the camera at all times. Do not strike the

camera with your fists or shake it. The camera should be stored and

treated with care to avoid any damage.

➂ Do not put or operate the camera in rain or wet places.

➃ Do not scrub the camera body with rough sandpaper when it is stained.

Please use a dry cloth at all times.

⑤ Put the camera in a cool area free from direct light. Otherwise, the

camera may be damaged.

What should be done during installation and use

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 13

E

14

Connecting Auto Iris Lens Connector

Prepare the Auto Iris lens connector, a camera auxiliary, as follows :

Connect each uncovered shutter control cable wire to the Auto Iris lens

connector as follows.

Pin No. DC Control Type VIDEO Control Type

1 Damp(-) Power (+12V)

2 Damp(+) N/A

3Drive(+) VIDEO Signal

4 Drive(-) GROUND

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 14

E

15

Installation

Lens Fixing

In case of CS lenses

Turn the CS lens clockwise until it is fixed as shown as follows.

In case of C lenses

Turn the C-mount adapter clockwise to fix it. Then turn the C lens

clockwise until it is fixed as follows.

CS lens

C lens

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 15

E

16

Setting Switch Control

Back Focus Adjustment

You should change the position of the lens setting switch on the side of the

camera according to the lens type. Depending on whether you fixed the DC

control type Auto Iris lens or video control type automatic shutter lens, you

should put the switch in "DC" or "VIDEO" position respectively.

The camera back focus is adjusted at the plant before delivery, but some

lenses are out of focus though the number differs in types. If it's the case,

you should make the back focus adjustment as follows. First, this is the

back focus adjustment procedure for fixed focus lenses.

Lenses without zoom function

① Image an object with high resolution(letticed) at more than 10m distance

and put the lens focus ring in the infinite(

∞

) position.

➁ Rotate the BACK FOCUS control bar until the object is seen best.

➂ Tighten the BACK FOCUS control bar fixing screw.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 16

E

17

Lenses with zoom function

① Image an object with high resolution(letticed) at a distance of 3 to 5 m

and zoom in the lens as close to TELE as possible. Then adjust the lens

focus bar until the object is seen best.

➁ Zoom in the lens as close to WIDE as possible and adjust the BACK

FOCUS adjustment bar until the object is seen best.

➂ Repeat from ① to ➁ above 2 or 3 times until the focus on the ZOOM

TELE side is in line with that on the ZOOM WIDE side.

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 17

E

18

Connecting Cables and Checking Operation

1 First, connect the connector of the BNC cable to the Video Out terminal

2 Second, connect the other connector of the BNC cable to the Video In

terminal.

3 Then, connect the power adapter. Connect a part of the power adapter

composed of 2 lines to the Camera Power In terminal with a flat-head

driver as follows.(GND : marked with a white line)

* Power source may be AC24V or DC12V irrespective of polarity

BNC cable

Video Out Terminal

Video In Terminal of

Monitor Rear Surface

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 18

E

19

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 19

20

Chapter 5 Camera Set-Up

E

This chapter describes how to set up the camera. The first part

describes the whole set up menu and composition and the second part

describes the function of each menu.

ON...

ALC...

ELC...

BW...

EXT...

AUTO...

USER...

COLOR...

MANU...

LINE...

MOTION DET ON...

CAMERA ID

ON.../OFF

CAMERA ID AND

LOCATION SETUP

DC IRIS SETUP

LEVEL SETUP

AREA SETUP

GAIN, AGC COLOR

SETUP

BURST SETUP

BURST, LEVEL,

DURATION SETUP

3200K/5600K/USER

RED, BLUE SETUP

PHASE SETUP

AREA SETUP

SENSITIVITY SETUP

BAU DRATE D-ZOOM, PIP,

MIRROR,

POSI/NEGA,DETAIL,

MOTION DET

IRIS

ALC.../ELC...

COLOR/BW

COLOR.../BW.../

AUTO.../EXT...

SHUTTER

OFF/1/100~1/10K

OFF/AUTO X2~X128

OFF/FIX X2~X128

AGC

OFF/LOW

/HIGH

MOTION

S.SLOW~F.FAST

WHITE BAL

ATW/AWC/MANU...

SYNC

INT/LINE...

SETUP

MENU

SPECIAL

...

EXIT

QUIT/SAVE/PRESET

BLC

OFF/BOTTOM.../

TOP.../LEFT.../

RIGHT.../

CENTER.../USER..

B2303(P)/2003P/B2307P/2007P 2007.5.15 5:7 PM Page 20

Sayfa yükleniyor...

Samsung SCC-B2007P Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Samsung SCC-B2007P Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler