Yamaha PM5D/PM5D-RH El kitabı

DIGITAL MIXING CONSOLE

PM5D / PM5D-RHPM5D / PM5D-RH

PM5D / PM5D-RH

Owner’s ManualOwner’s Manual

Owner’s Manual

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur afdankt

of de volgende Yamaha Service Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

•For the removal of the battery at the moment of the disposal at the

end of the service life please consult your retailer or Yamaha Service

Center as follows:

Yamaha Music Nederland Service Center

Address : Kanaalweg 18-G, 3526 KL UTRECHT

Tel: 030-2828425

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

This product contains a high intensity lamp that contains

a small amount of mercury. Disposal of this material

may be regulated due to environmental considerations.

For disposal information in the United States, refer to

the Electronic Industries Alliance web site:

www.eiae.org

(mercury)* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(5)-1

1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Use only the speciﬁed power supply (PW800W or an equivalent recommended

by Yamaha).

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device or the power supply should be dropped or damaged, immediately

turn off the power switch, disconnect the electric plug from the outlet, and have

the device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Do not turn the PW800W POWER switch OFF and ON in rapid succession.

Doing so can result in excessive current ﬂow that can cause damage. Wait at

least 5 seconds before turning the POWER switch ON after it has been turned

OFF.

• When transporting or moving the device, always use four or more people.

• Before moving the device, remove all connected cables.

•Avoid setting all equalizer controls and faders to their maximum. Depending on

the condition of the connected devices, doing so may cause feedback and may

damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the front and rear to

prevent the internal temperature from rising too high. In particular, do not place

the device on its side or upside down, or place it in any poorly-ventilated

location, such as a bookcase or closet.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the device, TV, or radio may

generate noise.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord Location

(5)-1

2/2

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Do not insert your ﬁngers or hand in any gaps or openings on the device (vents

etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not use the headphones for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery. When you unplug the power cord from

the AC outlet, the internal data of current scene is retained. However, if the

backup battery fully discharges, this data will be lost. When the backup battery

is running low, the LCD display indicates “Low Battery!” during operation or

“No Battery!” when starting up the system. In this case, have qualiﬁed Yamaha

service personnel replace the backup battery.

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Connections

Handling caution

Backup battery

6

PM5D/PM5D-RH Owner’s Manual

Table of Contents

Table of Contents — Operating section

1

Introduction ........................................ 10

Thank you................................................................... 10

An overview of the PM5D........................................... 10

Differences between the PM5D model and the

PM5D-RH model ............................................. 11

About the channel structure of the PM5D.......................... 12

Regarding word clock synchronization ....................... 12

How this manual is organized..................................... 13

Conventions in this manual ................................................. 13

2

Top, front, and rear panels................. 14

Top panel ................................................................... 14

Rear panel................................................................... 16

Front panel ................................................................. 18

3

Basic operation on the PM5D............. 19

About the various types of user interface .................... 19

User interface in the display.................................................. 19

DISPLAY ACCESS section ................................................... 20

Data Entry section ................................................................. 20

External user interface........................................................... 21

Basic operation ........................................................... 22

Click........................................................................................ 22

Drag ........................................................................................ 22

Drag and drop........................................................................ 22

Accessing a desired screen..................................................... 23

Moving the cursor ................................................................. 23

Scrolling the screen................................................................ 24

Operating the buttons........................................................... 25

Adjusting the setting of a knob or fader .............................. 25

Assigning a name................................................................... 26

4

Connections and setup ....................... 27

Audio connections ...................................................... 27

Analog audio connections .................................................... 27

Analog output connections .................................................. 28

Digital input/output connections ........................................ 29

Installing an option card....................................................... 30

Word clock connections and settings.......................... 31

About word clock .................................................................. 31

Selecting the word clock master ........................................... 31

Restoring the current scene to the default state.......... 32

5

Input channel operations ................... 33

About the input channels ........................................... 33

AD IN section.............................................................. 35

Items in the AD IN section ................................................... 35

Controlling the input sensitivity and phantom power

(+48V) of the head amp.............................................. 36

INPUT channel strip.................................................... 37

Items in the INPUT channel strip........................................ 37

ST IN/FX RTN channel strip ........................................ 39

Items in the ST IN/FX RTN channel strip........................... 39

FADER FLIP/ENCODER MODE section ........................ 40

Items in the FADER FLIP/ENCODER MODE section...... 40

Various operations for input channels ......................... 41

Selecting the function of the encoders................................. 41

Exchanging the fader and encoder functions...................... 41

Sending a signal from an input channel to the STEREO

bus ................................................................................. 42

Sending the signal from the input channel to a MIX

bus ................................................................................. 43

Enabling/disabling pairing....................................................45

6

Output channel operations .................47

About the output channels..........................................47

MIX section .................................................................49

Items in the MIX section....................................................... 49

Operations in the MIX section ............................................. 49

STEREO A/B channel strip............................................53

Items in the STEREO A/B channel strip..............................53

Operations in the STEREO A/B channel strip ....................54

MATRIX section...........................................................55

Items in the MATRIX section............................................... 55

Operations in the MATRIX section ..................................... 55

7

Using the Selected Channel section ...57

About the SELECTED CHANNEL section......................57

Items in the SELECTED CHANNEL section ...................57

GROUP................................................................................... 57

CHANNEL SELECT.............................................................. 58

DELAY.................................................................................... 58

GAIN/ATTENUATION/ø (Gain / Attenuation / Phase)...59

NOISE GATE ......................................................................... 59

STEREO.................................................................................. 60

COMPRESSOR...................................................................... 60

HPF (High Pass Filter) .......................................................... 61

EQUALIZER .......................................................................... 61

Operations in the SELECTED CHANNEL section ..........62

Selecting a channel and editing its parameters.................... 62

Compressor operations.........................................................63

Gate operations......................................................................64

EQ/HPF operations ...............................................................65

8

Input Patch / Output Patch operations ..66

Changing the input patch settings..............................66

Changing the output patch settings ...........................67

Inserting an external device into a channel .................69

Connecting an external device for insertion........................ 69

Patching the insert-out and insert-in................................... 70

Directly outputting the signal of an input channel ......72

9

Grouping and linking ..........................73

About DCA Groups and Mute Groups.........................73

Items in the ASSIGN MODE section ............................73

Items in the DCA strip .................................................73

Using DCA Groups ......................................................74

Assigning channels to DCA groups...................................... 74

Controlling DCA groups.......................................................75

Using mute groups......................................................75

Assigning channels to mute groups......................................75

Controlling mute groups ......................................................76

Using the Mute Safe function............................................... 76

Using EQ Link and Compressor Link............................77

PM5D/PM5D-RH Owner’s Manual

Table of Contents

7

10

Scene memory..................................79

About scenes .............................................................. 79

Items in the SCENE MEMORY section......................... 80

Using scene memories................................................ 81

Storing a scene........................................................................81

Recalling a scene.....................................................................82

Using PREVIEW mode ................................................. 82

Using the Auto Store function .................................... 83

Using the Direct Recall function.................................. 83

Using the Selective Recall function ............................. 84

Using the Recall Safe function..................................... 86

Using the Fade function.............................................. 87

Using the Tracking Recall function.............................. 88

Using the Global Paste function.................................. 89

11

Monitor and Cue..............................91

About the MONITOR and CUE sections...................... 91

Using the Monitor function ........................................ 92

Items in the MONITOR section ...........................................92

Monitoring a signal................................................................93

Using the Cue/Solo functions ..................................... 94

Items in the CUE section.......................................................94

About CUE mode and SOLO mode.....................................94

Cue and Solo groups..............................................................95

Using the Cue function..........................................................96

Using the Solo function .........................................................96

12

Talkback and Oscillator....................97

About the TALKBACK/OSCILLATOR sections .............. 97

Items in the TALKBACK/OSCILLATOR sections..............97

Using talkback ............................................................ 98

Using the oscillator ..................................................... 99

13

Meters.............................................100

Items in the meter section ........................................ 100

Switching the meter display ..................................... 100

Switching the metering point................................... 101

Specifying the metering point for input channels ............ 101

Specifying the metering point for output channels.......... 101

Viewing the gain reduction of the internal gates and

compressors .................................................. 102

Viewing the gain reduction for input channels ................ 102

Viewing the gain reduction for output channels.............. 102

14

Effects .............................................103

About the internal effects ......................................... 103

Using an internal effect via a MIX bus....................... 104

Inserting an internal effect into a channel................. 105

Basic operations in the effect screen ......................... 106

Recalling settings from the effect library ........................... 106

Editing the effect parameters.............................................. 106

Storing settings in the effect library ................................... 107

Using the Tap Tempo function................................. 108

Using the Freeze effect ............................................. 109

Using optional Add-On Effects.................................. 109

15

Graphic EQ .....................................110

Patching the graphic EQ ...........................................110

Basic graphic EQ operations......................................111

Controlling the graphic EQ from the display ................... 111

Controlling the graphic EQ from the DCA section.......... 111

16

Remote control ..............................113

MIDI on the PM5D ...................................................113

Using program changes to control events.................113

Using control changes to control events ...................115

Using the MIDI Remote function...............................117

Assigning MIDI messages to controllers ........................... 117

Using MIDI remote channels............................................. 121

Transmitting MIDI events when you switch scenes ...122

Using GPI (General Purpose Interface) ......................123

Using GPI IN ....................................................................... 123

Calibrating the GPI IN ports .............................................. 125

Using GPI OUT................................................................... 126

17

Using memory cards......................128

Using memory cards with the PM5D ........................128

Saving files to a memory card ...................................128

Loading files from a memory card.............................130

18

Surround pan.................................132

About surround pan..................................................132

Bus configuration and operation in surround mode..133

About the surround buses .................................................. 133

How the MIX section will operate ..................................... 133

Basic settings for surround buses...............................134

Controlling surround pan..........................................135

Notes regarding surround pan..................................137

19

Other functions..............................138

Using the user defined keys.......................................138

Items in the USER DEFINED section................................ 138

Assigning functions to the User Defined keys................... 138

Executing functions assigned to the User Defined keys... 139

Using the Fader Assign function................................139

Items in the FADER MODE section.................................. 139

Assigning channels to DCA faders..................................... 139

Controlling the channels assigned to DCA faders ............ 140

Locking the PM5D (Security functions) .....................141

Setting the System Password or Console Password.......... 141

Using Parameter Lock or Console Lock............................ 142

Using cascade connections .......................................143

Making cascade connections .............................................. 143

Basic settings for cascade connection ................................ 143

Selecting the buses used for cascade connection .............. 144

Connecting the PM5D to a computer via USB ..........146

Caution when using the USB TO HOST connector ........ 146

Initializing the PM5D’s internal memory ...................147

Adjusting the faders and input/output gain

(Calibration) ..................................................147

Calibrating the faders.......................................................... 148

Adjusting the analog input gain (PM5D-RH model

only)............................................................................ 148

Adjusting the output gain................................................... 148

8

PM5D/PM5D-RH Owner’s Manual

Table of Contents

Table of Contents — Reference section

Information shown in the display.......... 149

Upper part of the display (always visible).................. 149

Main area of the display............................................ 150

Lower part of the display (always visible) .................. 150

Function menu........................................ 151

Global functions...................................... 152

EFFECT functions ...................................................... 152

EFFECT PARAM (Effect parameter) screen..................... 152

EFFECT ASSIGN screen ..................................................... 154

EFFECT LIBRARY screen................................................... 155

GEQ function............................................................ 156

GEQ PARAM (GEQ parameter) screen ............................ 156

GEQ ASSIGN screen ........................................................... 157

GEQ LIBRARY screen......................................................... 158

SCENE function ........................................................ 159

SCENE screen ...................................................................... 159

EVENT LIST screen ............................................................ 161

SELECTIVE RECALL screen.............................................. 164

RECALL SAFE screen.......................................................... 166

FADE TIME screen ............................................................. 167

TRACKING RECALL screen.............................................. 169

GLOBAL PASTE screen...................................................... 170

MIDI REMOTE function............................................. 171

MIDI SETUP screen............................................................ 171

MIDI PGM CHANGE (MIDI program change) screen .. 173

MIDI CTRL CHANGE (MIDI control change) screen ... 174

MIDI REMOTE screen ....................................................... 175

GPI screen ............................................................................ 177

FADER START screen ........................................................ 179

TRANSPORT screen........................................................... 181

DME CONTROL screen..................................................... 182

UTILITY function ....................................................... 186

PREFERENCE 1/2 screens.................................................. 186

USER DEFINE screen ......................................................... 189

SAVE screen ......................................................................... 192

LOAD screen........................................................................ 195

FADER ASSIGN screen....................................................... 197

SECURITY screen................................................................ 198

SYS/W.CLOCK function ............................................ 199

WORD CLOCK screen ....................................................... 199

MIXER SETUP screen......................................................... 200

CASCADE screen ................................................................ 204

HA (Head Amp) screen ...................................................... 206

OUTPUT PORT ATT (Output port attenuation) screen 207

DITHER screen.................................................................... 207

HA LIBRARY screen ........................................................... 208

METER function ........................................................ 209

INPUT METER screen........................................................ 209

OUTPUT METER screen ................................................... 210

INPUT GR (Input Gain Reduction) screen ...................... 211

OUTPUT GR (Output Gain Reduction) screen............... 211

MON/CUE function .................................................. 212

TALKBACK screen.............................................................. 212

OSCILLATOR screen.......................................................... 213

2TR I/O screen..................................................................... 215

MONITOR screen............................................................... 216

CUE/SOLO screen............................................................... 217

Output functions .................................... 220

OUTPUT PATCH function..........................................220

OUTPUT PATCH screen ...................................................220

INSERT PATCH screen ...................................................... 221

INSERT POINT screen .......................................................222

OUTPUT PATCH LIBRARY screen..................................223

OUTPUT INSERT function..........................................224

INSERT IN MIX 1-24 screen.............................................. 224

INSERT IN MATRIX/STEREO/MONITOR screen ........224

HA LIBRARY screen ...........................................................225

OUTPUT EQ function ................................................225

EQ PARAM (EQ Parameter) screen ..................................225

MIX 1-24 screen................................................................... 227

MATRIX/STEREO screen...................................................227

OUTPUT EQ LIBRARY screen..........................................228

OUTPUT COMP function ..........................................229

COMP PARAM (Compressor parameter) screen ............ 229

MIX 1-24 screen................................................................... 231

MATRIX/STEREO screen...................................................231

COMP LIBRARY (Compressor library) screen ................ 232

OUTPUT DELAY function...........................................233

MIX 1-24 screen................................................................... 233

MATRIX/STEREO screen...................................................233

OUTPUT DCA/GROUP function.................................234

DCA GROUP ASSIGN screen............................................ 234

MUTE GROUP ASSIGN screen.........................................235

EQ LINK ASSIGN screen....................................................236

COMP LINK ASSIGN (Compressor link assign) screen .237

MATRIX/ST function..................................................238

MATRIX/ST ROUTING screen .........................................238

MIX to MATRIX VIEW screen ..........................................240

LCR screen ...........................................................................242

SURR SETUP screen ...........................................................244

OUTPUT VIEW function.............................................245

CH VIEW (Channel view) screen ......................................245

SIGNAL FLOW screen........................................................247

FADER VIEW screen ..........................................................249

CH COPY (Channel copy) screen......................................249

OUTPUT CH LIBRARY screen .........................................251

PM5D/PM5D-RH Owner’s Manual Table of Contents 9

Input functions ........................................252

INPUT PATCH function............................................. 252

INPUT PATCH screen ....................................................... 252

DIRECT OUT PATCH screen ........................................... 253

INSERT PATCH screen...................................................... 254

INSERT/DIRECT OUT POINT screen............................. 256

NAME screen....................................................................... 257

INPUT PATCH LIBRARY screen ..................................... 257

INPUT HA/INSERT function ...................................... 258

CH 1-24 (Input channel 1-24) screen ............................... 258

STIN/FXRTN (ST IN/FXRTN channel) screen ............... 258

INSERT 1-24 screen............................................................ 259

INSERT 25-48 screen.......................................................... 259

INSERT STIN screen .......................................................... 259

HA LIBRARY screen........................................................... 260

INPUT ø/EQ function................................................ 260

EQ PARAM (EQ parameter) screen.................................. 260

EQ 1-24 screen..................................................................... 261

EQ 25-48 switch .................................................................. 261

EQ STIN/FXRTN screen .................................................... 261

ø/ATT 1-48 (Phase/Attenuation 1-48) screen .................. 262

ø/ATT STIN/FXRTN (Phase/Attenuation STIN/FXRTN)

screen .......................................................................... 262

INPUT EQ LIBRARY screen.............................................. 263

INPUT GATE/COMP function ................................... 264

GATE PARAM (Gate parameter) screen .......................... 264

COMP PARAM (Compressor parameter) screen............ 266

CH 1-12 (Input channel 1–12) screen............................... 267

CH 13-24 (Input channel 13–24) screen........................... 267

CH 25-36 (Input channel 25–36) screen........................... 267

CH 37-48 (Input channel 37–48) screen........................... 267

ST IN (ST IN channel) screen............................................ 267

GATE LIBRARY screen ...................................................... 268

COMP LIBRARY (Compressor library) screen................ 269

INPUT DELAY function.............................................. 270

CH 1-24 (Input channel 1–24) screen............................... 270

CH 25-48 (Input channel 25–48) screen........................... 270

ST IN (ST IN channel) screen............................................ 270

INPUT DCA/GROUP function ................................... 271

DCA GROUP ASSIGN screen ........................................... 271

MUTE GROUP ASSIGN screen ........................................ 272

EQ LINK ASSIGN screen ................................................... 272

COMP LINK ASSIGN (Compressor link assign) screen. 273

PAN/ROUTING function ........................................... 274

CH to MIX (Channel to mix) screen................................. 274

MIX SEND VIEW screen ................................................... 280

FIX ASSIGN VIEW screen ................................................. 282

LCR screen........................................................................... 283

SURR PARAM (Surround parameter) screen.................. 283

SURR VIEW (Surround view) screen ............................... 285

M/S screen............................................................................ 285

INPUT VIEW function................................................ 286

CH VIEW (Channel view) screen...................................... 286

SIGNAL FLOW screen ....................................................... 287

FADER VIEW screen.......................................................... 288

CH COPY screen................................................................. 289

INPUT CH LIBRARY (Input channel library) screen..... 289

Appendices..............................................290

EQ Library List ...........................................................290

GATE Library List .......................................................291

Compressor Library List.............................................292

Dynamics Parameters................................................294

GATE section....................................................................... 294

COMP section ..................................................................... 295

Effect Library List .......................................................297

Effects Parameters .....................................................298

Effects and tempo synchronization.................................... 307

Scene Memory/Effect Library to Program Change

Table .............................................................308

Parameters that can be assigned to control changes.312

Control change parameter assignments....................314

NRPN parameter assignments...................................331

Channel Library List ..................................................334

Channel parameter behavior when paired ................335

MIDI Data Format .....................................................336

Warning Messages ....................................................343

Error Messages..........................................................344

Troubleshooting........................................................345

General Specifications ...............................................346

Input/output characteristics ......................................348

Electrical characteristics.............................................352

Other Functions ........................................................354

Pin Assignment .........................................................355

Dimensions ...............................................................356

MIDI Implementation Chart......................................357

Index.........................................................................358

PM5D/PM5D-RH Block Diagram.............. End of Manual

PM5D Level Diagram ............................... End of Manual

PM5D-RH Level Diagram ......................... End of Manual

• The illustrations and screen displays as shown in this

Owner’s Manual are for instructional purposes only,

and may be different from the ones on your device.

• The company names and product names in this

Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

10 PM5D/PM5D-RH Owner’s Manual Operating section

Operating section

Thank you

Thank you for purchasing the Yamaha PM5D digital mixing console. In order to take full advantage of the PM5D’s superior

functionality and enjoy years of trouble-free use, please read this manual before you begin using the product. After you have

read the manual, keep it in a safe place.

An overview of the PM5D

The PM5D is a digital mixing console with the following features.

❏ Full digital SR mixing system

The PM5D is a full-digital SR mixing console that takes

advantage of cutting-edge digital audio processing technol-

ogy. 24-bit linear AD/DA converters are used to deliver up

to 110 dB of dynamic range and amazing sound quality. As

input channels, it provides 48 monaural channels, four ste-

reo channels, and four stereo channels for effect return. As

output channels, it provides 24 MIX channels, eight

MATRIX channels, and two STEREO channels. The PM5D

can be used in a wide range of applications. You can assign

desired channels to be controlled by the eight DCA faders

on the panel, and use them as group faders.

❏ PM5D model and PM5D-RH model

In addition to the standard PM5D model that provides

manual control of the head amp for each input, the

PM5D-RH model is also available, providing programma-

ble control of head amp input sensitivity and phantom

power settings. You can choose the model appropriate for

your situation and budget.

❏ Cutting-edge user interface

For the input channels and STEREO A/B channels, dedi-

cated channel strips are provided where you can operate

the fader, pan, cue, and on/off controls. For MIX channels

and MATRIX channels, encoders allow you to control the

send level and master level. The PM5D allows quick and

intuitive operation just as on an analog mixer. In addition,

you can use the SELECTED CHANNEL section to manu-

ally control the principal parameters (delay, EQ, gate,

compressor) of the desired channel.

❏ Eight effect modules / Twelve graphic

EQ modules

Eight high-quality multi-effect modules are built in. Effects

such as reverb, delay, multiband compressor, and various

modulation effects can be routed via internal buses or

inserted into the desired channel. 31-band graphic EQ can

also be inserted into any channel or any output.

❏ Scene memories and libraries

Mix parameters and internal effect settings can be stored in

memory as up to 500 scenes for immediate recall. Effects,

input/output patching, input channel/output channel set-

tings, internal head amp (PM5D-RH model only) or

external head amp settings can be stored in various librar-

ies, independently of scenes.

❏ Digital cascade connection

Up to four PM5D units, or one PM5D and one Yamaha

DM2000/02R96 unit, can be cascade-connected to share

buses in the digital domain. In particular when PM5D

units are cascaded together, operations such as scene sav-

ing and recall can also be linked. Compatible external

devices can also be used as inserts or as extended signal

processors via a cascade connection.

❏ Surround panning

Surround pan functionality allows multi-channel playback

systems to be used, letting you place the signal of an input

channel in two-dimensional space, or move the sound

image forward/backward and left/right. 3-1ch, 5.1ch, and

6.1ch surround modes are available.

❏ I/O card expansion

The rear panel provides four slots in which separately sold

mini-YGDAI cards can be installed. AD cards, DA cards, or

digital I/O cards can be installed in these slots to add inputs

and outputs.

❏ Add-On Effects provide additional effect

types

Separately sold Add-On Effects packages can be installed to

add new effect types for the internal effects. The REV-X

reverb effect sold as an Add-On Effect for the DM2000 or

02R96 is included as standard.

1 Introduction

PM5D/PM5D-RH Owner’s Manual Operating section 11

1

Introduction

Differences between the PM5D model and the PM5D-RH

model

The PM5D is available as the standard PM5D model or as the PM5D-RH model which allows internal head amp settings to be

programmed. These models differ as follows.

❏ PM5D model

• Head amp adjustments (input sensitivity settings,

phantom power (+48V) on/off) for the analog inputs

(INPUT jacks 1–48, ST IN jacks 1–4) are performed

manually, using the controls of the top panel.

• Insert jacks (INSERT IN/OUT jacks) for the monaural

analog inputs (INPUT jacks 1–48) are provided on the

rear panel, allowing external effect processors to be

inserted in the analog domain.

• ST IN jacks 1–4 are only for line level.

• There is no +48V MASTER switch.

❏ PM5D-RH model

• Head amp adjustments (input sensitivity settings,

phantom power (+48V) on/off) for the analog inputs

are controlled from within the screen via software. For

this reason, the top panel does not have head amp con-

trols; instead, indicators showing the presence or

absence of a signal are provided. Head amp settings can

be saved in a library and recalled at any time.

• Insert jacks for the analog inputs are not provided.

• ST IN jacks 1–4 support mic levels through line levels.

Phantom power can also be supplied to ST IN jacks 1–

4.

• The +48V MASTER switch turns all phantom power

(+48V) on/off.

INPUT jacks 1–48ST IN jacks 1–4

INSERT IN/OUT jacks 1–48

INPUT jacks 1–48

ST IN jacks 1–4

2 Introduction

12 PM5D/PM5D-RH Owner’s Manual Operating section

The PM5D provides the following input channels and out-

put channels.

❏ Input channels

This section processes input signals and sends them to the

STEREO bus or MIX buses. There are three types of input

channel, as follows.

• Input channels 1–48

These channels are used to process monaural signals.

By default, the input signals from the monaural analog

input jacks (INPUT jacks 1–48) are assigned to these

channels.

• ST IN channels 1–4

These channels are used to process stereo signals. By

default, the input signals from the stereo analog input

jacks (ST IN jacks 1–4) are assigned to these channels.

• FX RTN channels 1–4

These channels are used mainly to process the return

signals (stereo) from the internal effects. By default, the

left/right output channels of internal effects 1 through

4 are assigned to these channels.

Hint

Signal assignments to the input channels can be changed as

desired.

❏ Output channels

This section mixes the signals sent from input channels

etc., and sends them to the corresponding output jacks or

output buses. There are three types of output channel, as

follows.

• MIX channels 1–24

These process the signals sent from input channels to

MIX buses, and output them from MIX OUT jacks 1

through 24. These channels are used mainly for fold-

back or as sends to external effects. The signals of MIX

channels 1–24 can also be sent to the STEREO bus or

MATRIX buses.

• MATRIX channels 1–8

These process the signals sent from MIX channels or

STEREO A/B channels to MATRIX buses, and output

them from the MATRIX OUT jacks. This allows MIX

channels or STEREO A/B channels to be mixed at the

desired balance for output.

• STEREO A/B channels

These process the signals sent from input channels or

MIX channels, and output them to STEREO OUT

jacks A/B. These channels are used as the main stereo

outputs. Normally, the same signal is sent from the

STEREO A and B channels. However, it is also possible

to use the STEREO B channel as the center channel for

three-channel L/C/R playback.

Regarding word clock synchronization

The signal used to synchronize digital audio signal process-

ing is called “word clock.” Normally, one device transmits

a reference word clock signal, and the other devices receive

this word clock signal and synchronize to it.

In order to transmit or receive digital audio signals to or

from an external device via the PM5D’s digital input/out-

put jacks or via a digital I/O card installed in a slot, the

word clock must be synchronized between the devices. Be

aware that if the word clock is not synchronized, the sig-

nals will not be transmitted correctly, and unpleasant noise

will occur.

Hint

• For details on synchronizing the word clock of the PM5D

and external devices, refer to the explanation of word clock

in Operating section “Chapter 4. Connections and setup”

(

➥

p.31), and to the Reference Section “WORD CLOCK

screen” (

➥

p.199).

• As an exception, digital signals that are not synchronized

with the PM5D can be input via a digital I/O card that con-

tains a sampling rate converter, or via the 2TR IN/OUT

DIGITAL jacks.

About the channel structure of the

PM5D

PM5D/PM5D-RH Owner’s Manual Operating section 13

1

Introduction

How this manual is organized

This owner’s manual is divided into the following three

sections.

❏ Operating section

This section explains the items on the front and rear pan-

els, connections and setup, and how to operate the PM5D’s

basic functionality. In particular if you have not operated a

digital console before, we recommend that you read chap-

ters 2 through 7 first.

❏ Reference section

This section explains the functionality and operation for all

of the PM5D’s screens. Refer to this section when you want

to learn about the items in the screens.

❏ Appendices

This contains various information such as library lists,

parameter lists for the internal effects, the MIDI data for-

mat, and lists of warning messages and error messages.

In this manual, non-locking panel switches that you press

are called “keys,” and those that change their on/off status

when you push them in (locking types) are called

“switches.” Of the control knobs on the panel, those that

turn from a minimum value to a maximum value are

called “knobs,” while those that turn endlessly are called

“encoders.”

Controls located on the panel are enclosed in square brack-

ets [ ] (e.g., [CUE] key, [PAD] switch) in order to

distinguish them from the buttons and knobs displayed in

the screen. For some controls, the section name is listed

before the [ ] (e.g., CH [ON] key, EQ [FREQUENCY]

encoder).

Unless otherwise specified, references to the PM5D apply

to both the PM5D model and the PM5D-RH model. If

specifications differ between the PM5D model and the

PM5D-RH model, such differences will be noted each time

they occur.

Conventions in this manual

2 Top, front, and rear panels

14 PM5D/PM5D-RH Owner’s Manual Operating section

This chapter explains the names and functions of each part of the PM5D. Details for each section of

the top panel are explained in subsequent chapters of this operating section; refer to the appropri-

ate chapter for more information.

Top panel

A AD IN section (PM5D model)

In this section you can adjust the sensitivity of the ana-

log signals being input from the rear panel INPUT

jacks 1–48 and ST IN jacks 1–4, and switch pad, insert,

and phantom power (+48 V) on/off (➥ p.35).

B AD IN section (PM5D-RH model)

This area indicates the presence, peak level, and phan-

tom power (+48V) on/off status of the input signal

from rear panel INPUT jacks 1–48 and ST IN jacks 1–

4.

Hint

For the PM5D-RH model, input sensitivity and phantom power

on/off are controlled by operations in the display (

➥

p.36).

C INPUT channel strip section

This section controls the principal parameters for input

channels 1–48 (➥ p.37).

D FADER FLIP/ENCODER MODE section

Here you can select the parameters controlled by the

faders/encoders of the INPUT channel strip (

3)

(➥ p.40).

E MIX section

This section controls the on/off status and send level of

the signals sent from input channels to MIX buses, and

adjusts the master level of the MIX channels (➥ p.49).

F MATRIX section

This section controls the send level of the signals sent

from MIX channels to MATRIX buses, and adjusts the

master level of the MATRIX channels (➥ p.55).

G SELECTED CHANNEL section

In this section you can view and control the mix

parameters for the currently selected input channel or

output channel (➥ p.57).

H Meter section

This section contains peak level meters that indicate

the input levels of input channels and the output levels

of output channels and cue monitoring, as selected by

key operations (➥ p.100).

2 Top, front, and rear panels

1

(PM5D model)

2

(PM5D-RH model)

4 5

3

6 8

7

PM5D/PM5D-RH Owner’s Manual Operating section 15

2

Top, front, and rear panels

I Display

This display shows the information you need to oper-

ate the PM5D, and lets you make system-wide settings

and control mix parameters for input and output

channels (➥ p.19).

Hint

You can adjust the angle of the display by moving the upper

part of the display frame forward or backward.

Note

Before moving the PM5D, you must lower the display all the

way back until it is fastened in place.

J FADER MODE section

Here you can select the combination of channels or

DCA groups that will be controlled by the faders of the

DCA strip section (

K) (➥ p.73).

K DCA strip section

From this section you can control the channels

assigned to DCA groups 1–8 (➥ p.73).

L ST IN/FX RTN (Stereo in / Effect return)

channel strip section

This section controls the principal parameters of ST IN

channels 1–4 or FX RTN channels 1–4 (➥ p.39).

M STEREO strip section

This section controls the principal parameters of the

STEREO A/B channels (➥ p.53).

N SCENE MEMORY section

This section stores/recalls mix parameters as scene

memories (➥ p.80). Mute operations for mute groups

1–8 are also performed in this section (➥ p.75).

O CUE/MONITOR section

This section selects the monitor source that is output

from the MONITOR OUT jacks, and adjusts the lev-

els. This section also determines the cue point and

monitoring method that will be used when you press a

[CUE] key for a channel (➥ p.91).

P OSCILLATOR/TALKBACK section

This section switches the oscillator or talkback on/off,

and adjusts the talkback level (➥ p.97).

Q DISPLAY ACCESS section

This section selects the functions or screen shown in

the display (➥ p.20).

R USER DEFINED KEYS sections

This section executes the functions that have been

assigned to the User Defined keys [1]–[25] (➥ p.138).

S Data entry section

This section lets you move the pointer (the arrow dis-

played in the screen) or cursor (the red frame

indicating a selection) in the display and edit the

parameter value (➥ p.20).

T ASSIGN MODE section

This section lets you assign mute groups and DCA

groups for control from the panel (➥ p.73).

R

9

Q

R

ST

N O P

8

J

K M L

2 Top, front, and rear panels

16 PM5D/PM5D-RH Owner’s Manual Operating section

Rear panel

A INPUT jacks 1–48 (PM5D model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–60 dBu to +10 dBu.

B INSERT IN/OUT jacks 1–48 (PM5D model

only)

These are balanced TRS phone type input/output jacks

for inserting external effects or dynamics processors

etc. into INPUT jacks 1–48. Nominal input/output

level is +4 dBu.

C ST IN (Stereo input) jacks 1–4 (PM5D

model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices.

Nominal input level is –34 dBu to +10 dBu.

D +48V MASTER switch (PM5D-RH model

only)

This is the master phantom power (+48V) switch for

INPUT jacks 1–48 and ST IN jacks 1–4. If this switch is

off, the +48V buttons shown in the display are

unavailable.

E INPUT jacks 1–48 (PM5D-RH model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–62 dBu to +10 dBu.

F ST IN (Stereo input) jacks 1–4 (PM5D-RH

model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–62 dBu to +10 dBu.

3 1

2

(PM5D model)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

1/4" TRS

phone plug

Tip (hot)

Ring (cold)

Sleeve (ground)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

46

5

(PM5D-RH model)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

PM5D/PM5D-RH Owner’s Manual Operating section 17

2

Top, front, and rear panels

G MIX OUT jacks

These are XLR-3-32 (balanced) jacks that output the

analog signals of MIX channels 1–24. Nominal output

level is +4 dBu.

H LAMP connector

This is a four-pin female XLR output jack for supply-

ing power to a gooseneck lamp. (These jacks are

provided at three locations). The location of these jacks

differs between the PM5D model and the PM5D-RH

model.

I MONITOR OUT jacks

These are XLR-3-32 (balanced) jacks that output the

monitor signal selected in the MONITOR section of

the top panel. Nominal output level is +4 dBu.

Note

Although the various output jacks and 2TR IN ANALOG jacks

have a nominal input/output level of +4 dBu (maximum level is

+24 dBu), an internal switch allows this to be changed to

–2 dBu (maximum level +18 dBu) if necessary. For details,

contact your Yamaha dealer.

J CUE OUT jacks

These are XLR-3-32 (balanced) jacks that output the

cue monitor signal from the channel selected by its

[CUE] key. Nominal output level is +4 dBu.

K STEREO OUT A/B jacks

These are XLR-3-32 (balanced) jacks that output the

analog signals of the STEREO A/B channels. Nominal

output level is +4 dBu.

L MATRIX OUT jacks

These are XLR-3-32 (balanced) jacks that output the

analog signals of MATRIX channels 1–8. Nominal out-

put level is +4 dBu.

M DC POWER INPUT connector

This is a connector for connecting the PW800W power

supply. Use the dedicated cable included with the

PM5D to make the connection.

N 2TR IN ANALOG jacks 1/2

These are XLR-3-31 (balanced) jacks that input stereo

analog signals from an external source. Nominal input

level is +4 dBu.

O TIME CODE INPUT jack

This is an XLR-3-31 (balanced) jack that receives

SMPTE time code (LTC) from an external source.

P TO HOST connector

This is a USB (type B) connector that allows communi-

cation with a computer.

Q GPI connector

This is a D-sub 25-pin female connector that allows

communication with a GPI-equipped external device.

7

8

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

C

RLRL

87654321

MJ9KL

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

IN

R

L

R

L

SMPTE

USB

OUT IN

75

ON OFF

21

COAXIAL COAXIALAES/EBU AES/EBU AES/EBU AES/EBU

3

21

3

THRU OUT IN

N X YVUT

Q R S Z aWPO

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

2 Top, front, and rear panels

18 PM5D/PM5D-RH Owner’s Manual Operating section

R RS422 REMOTE connector

This is a D-sub 9-pin female connector for remotely

controlling an external device that supports the RS422

protocol.

S HA REMOTE connector

This is a D-sub 9-pin male connector for remotely con-

trolling an external head amp device (e.g., Yamaha

AD8HR or AD824) that supports a special protocol.

T WORD CLOCK IN connector

This is a BNC connector for supplying a word clock

from an external device to the PM5D.

U 75Ω ON/OFF switch

This switch terminates the word clock connection.

Normally you will leave this ON. If a device made by

another manufacturer is connected and word clock

cannot be received correctly, try turning this OFF.

V WORD CLOCK OUT connector

This is a BNC connector for supplying a word clock

from the PM5D to an external device.

W MIDI IN/THRU/OUT connectors

These connectors are used to transmit and receive

MIDI messages to and from external MIDI devices.

The MIDI IN connector receives messages from an

external device, and the MIDI OUT connector trans-

mits messages from the PM5D. Messages received at

the MIDI IN connector are retransmitted without

change from the MIDI THRU connector.

X 2TR OUT DIGITAL (2 track out digital) jacks

1–3

These jacks digitally output the signals of the STEREO

A/B channels. Two types are provided; AES/EBU

(XLR-3-32) jacks (1/2) which output AES/EBU format

signals, and a COAXIAL (RCA phono) jack (3) which

outputs consumer format signals (IEC60958).

Y 2TR IN DIGITAL (2 track in digital) jacks 1–3

These jacks input digital audio from external devices

such as CD players. Two types are provided; AES/EBU

(XLR-3-31) jacks (1/2) which receive AES/EBU format

signals, and a COAXIAL (RCA phono) jack (3) which

receives consumer format signals (IEC60958).

Z CASCADE OUT connector

This is a D-sub half-pitch 68-pin female connector that

can be connected to another PM5D for transmission/

reception of control signals and transmission of audio

signals.

a CASCADE IN connector

This is a D-sub half-pitch 68-pin female connector that

can be connected to another PM5D for transmission/

reception of control signals and reception of audio

signals.

b Fan grille

This is an output grille for the fan that cools the inte-

rior of the console (two locations). Be careful not to

obstruct the fan exhaust.

c SLOT 1–4

These slots allow separately sold mini-YGDAI I/O

cards to be installed to expand the input/output ports.

Front panel

A MEMORY CARD slot

A memory card inserted in this slot can be used to

save/load scene memories or library data. You can use

PCMCIA Type II flash ATA cards, or CompactFlash

cards inserted into a PC card adaptor.

B MOUSE connector

A PS/2 mouse can be connected to this connector and

used to perform operations in the display.

C KEYBOARD connector

A PS/2 keyboard can be connected to this connector

and used to input text or perform operations in the

display.

D PHONES (Headphone) jack

This headphone jack lets you monitor the MONITOR

OUT or CUE signals.

cb

PHONES

KEYBOARD

MOUSE

MEMORY CARD

PHONES

KEYBOARD

MOUSE

MEMORY CARD

12

43

56

12

43

56

1 2 3 4

PM5D/PM5D-RH Owner’s Manual Operating section 19

3

Basic operation on the PM5D

This chapter explains the various types of user interface used to operate the PM5D.

About the various types of user interface

Basic parameters such as mixing and editing the sound of each channel can be controlled by the faders and encoders of the top

panel. However to make more detailed settings, you will need to access the appropriate “function” and edit the parameter val-

ues in the display. The section below explains the various user interface components shown in the display, and how to use

them.

The user interface in the PM5D’s display uses the follow-

ing components.

❏ Pointer

The arrow shown in the display is called the “pointer.” Use

the pointer to select the parameter you want to control

next.

❏ Cursor

The red frame shown in the display is called

the “cursor.” If the cursor encloses a parame-

ter on the screen, that parameter is selected

for operation.

❏ Tabs

The screen names shown in

the upper left of the display

are called “tabs.” Tabs are

used to switch between

screens within the same

function.

❏ Buttons

Buttons in the display are

used to switch parameters

on/off or to select one of

multiple choices. Buttons

that are currently on are dis-

played in green (some

buttons are displayed in red

or blue); buttons that are

turned off are displayed in

gray.

❏ Knobs/Faders/Boxes

Knobs/faders in the display are used to edit parameter val-

ues. The current value is shown in the box. Boxes for which

/ buttons are displayed at left and right allow you to

edit the parameter by using these buttons. (If editing is not

possible, the buttons will be gray.)

If you want to assign a name to a channel or scene, input

characters, numerals, and symbols into the box.

❏ Character palette

This is a “virtual” keyboard used to input characters,

numerals, and symbols into a text input box.

3 Basic operation on the PM5D

User interface in the display

Cursor

Ta b

Buttons turned

off (gray)

Buttons turned

on (green)

Fader

Box

Knob

/ buttons for

editing the value

3 Basic operation on the PM5D

20 PM5D/PM5D-RH Owner’s Manual Operating section

❏ Scroll bar

If the displayed items are too numerous to fit into a single

screen, you can use the scroll bar to view the portion that is

not currently displayed.

The DISPLAY ACCESS section contains keys that access

the desired function or screen in the display.

A Global functions

These keys access functions that affect the entire

PM5D.

B Output functions

These keys access functions that are related to output

channels.

C Input functions

These keys access functions that are related to input

channels.

When you press the key for the desired function, the screen

for that function will appear in the display. By repeatedly

pressing a key you can cycle through the screens included

in that function.

Hint

If you hold down the [SHIFT] key and press a key in the DIS-

PLAY ACCESS section, the screens included in that function

will appear in the reverse order (Page Back function). You can

also use the Page Back function by holding down a key in the

DISPLAY ACCESS section. If you rapidly press a key twice,

you will return to the first screen in that function.

Controllers used to edit settings and values in the display

are gathered into the data entry section.

A [DEC/CANCEL]/[INC/OK] keys

Use these keys to increase or decrease the value of the

parameter where the cursor is located. If the PM5D has

displayed a window asking you to confirm an opera-

tion such as recall or store, these buttons can be used

instead of the CANCEL button and OK button shown

in the window.

B CURSOR [√]/[®]/[π]/[†] keys

These keys are used to move the cursor to the desired

parameter.

C [SHIFT] key

This key can be used in conjunction with the CUR-

SOR [√]/[®]/[π]/[†] keys to move the cursor

rapidly, or in conjunction with the [DATA] encoder or

[DEC]/[INC] keys to change the parameter value

rapidly.

If you hold down the [SHIFT] key and press the

[ENTER] key, the JOB SELECT window will appear,

allowing you to set multiple parameters in a single

operation. (When you move the cursor to a parameter

for which there is a JOB SELECT window, an indica-

tion of “Job Select = [SHIFT] + [ENTER]” will

appear.)

D [ENTER] key

Use this key to switch a button at the cursor location

on/off, or to open a window.

E [DATA] encoder

Use this to increase or decrease the value of the param-

eter where the cursor is located. The parameter value

will change more rapidly if you turn the [DATA]

encoder while holding down the [SHIFT] key.

Scroll bar

DISPLAY ACCESS section

1

2

3

Data Entry section

2

1

6

3

7

4

5

Sayfa yükleniyor ...

Yamaha PM5D/PM5D-RH El kitabı

Bu kılavuz için de uygundur

Yamaha PM5D/PM5D-RH El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler