YAMADA TSX-W80LB El kitabı

TSX-W80

Printed in China

WS68080

G

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

TSX-W80

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

i En

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place - away from direct sunlight, heat sources,

vibration, dust, moisture and cold. For proper

ventilation, allow the following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in an environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit,

and/or personal injury. Yamaha will not be held

responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power

cable disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press to set the system to

off, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the system off, then leave this

unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat

such as sunshine, fire or the like. When you dispose

of batteries, follow your regional regulations.

22 Be sure to use the AC adaptor supplied with this unit.

Using an AC adaptor other than the one provided

may cause fire or damage to this unit.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off by . In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Do not use this unit within 22 cm (9 in) of persons with a

heart pacemaker implant or defibrillator implant.

We, the manufacturer Yamaha hereby declare that the

TSX-W80 is in compliance with the essential

requirements and other relevant provisions of Directive

1999/5/EC.

There is a chance that placing this unit too close to a

CRT-based (Braun tube) TV set might impair picture

color. Should this happen, move this unit away from the

TV set.

1 En

English Français Deutsch Svenska Italiano Español Nederlands Русский

PREPARATION

NAMES OF PARTS AND THEIR FUNCTIONS

..................................................................................2

BASIC FUNCTIONS..............................................4

LISTENING TO iPod™ AND EXTERNAL

SOURCES ...............................................................6

LISTENING TO RADIO STATIONS ................. 8

TROUBLESHOOTING......................................... 9

SPECIFICATIONS.............................................. 12

■ Features

– Hi-quality iPod/iPhone, radio and external device playability.

– Firm bass sound and spacious stereo sound from 2.1 ch powered speaker (tweeter × 2, woofer × 1), SR-

Bass™ (Yamaha Swing Radiator Bass technology) and DSP in a compact unit.

– Easy user-intuitive interface by buttons with Guide LED and knob dials.

■ Yamaha AirWired

Real-time uncompressed music transfer without sound degradation is realized by Yamaha original digital

wireless transfer technology, AirWired. You can also control system on/off and volume with the iPod by

AirWired.

y

You can use a subwoofer wirelessly with the Wireless subwoofer kit (SWK-W10, etc., sold separately). Refer to the owner’s

manual of the SWK-W10 for details.

■ About this manual

• This unit is iPod and also iPhone-compatible. “iPod” described in this manual may also refer to “iPhone”.

• This manual describes how to operate this unit using buttons on the unit. Some of these operations are also

available using the remote control.

■ Supplied accessories

■ Using the remote control ■ Replacing the battery in the remote

control

CONTENTS

Remote control AC adaptor Power cable Transmitter Indoor FM antenna

(DC 15 V, 2.66 A,

model number:

NU40-2150266-I3)

YIT-W11TX

Within 6 m

(20’)

CR2025

battery

2 En

■ Front and top panel

1 : Press to turn the system on/off.

Time is displayed even when the system is off.

y

• Press and hold on the top of the unit for more than 3

seconds to set the system to standby mode. All the

information on the front panel display is not displayed

in standby mode. This can reduce power consumption.

To cancel standby mode, press .

• Even in system off/standby mode, the alarm function is

available.

2 TIMER: Timer setting (☞ P. 5)

3 ALARM: Alarm on/off (☞ P. 4)

4 SET: Alarm setting (☞ P. 4)

5 Front panel display

6 SOURCE: iPod, AUX, RADIO

7 VOLUME: Volume control

8 PRESET: Storing your favorite 5 radio stations

(☞ P. 8)

9 SNOOZE/SLEEP (☞ P. 5)

0 DIMMER:

Setting brightness of the front panel

A (auto) 3 (brightest) 2 1 (darkest) back to A

y

When A (auto) is set, the brightness of the front panel is

adjusted automatically depending on the brightness of the

room.

A MEMORY (☞ P. 7, ☞ P. 8)

B TUNING (☞ P. 8)

C Charging cradle: For charging an iPod

D Illumination sensor: Measuring surrounding

illuminance. Do not cover this sensor.

NAMES OF PARTS AND THEIR FUNCTIONS

When charging an iPod,

1 Connect the iPod to the transmitter.

2 Set the iPod connected to the transmitter to the

charging cradle.

NAMES OF PARTS AND THEIR FUNCTIONS

3 En

English

■ Rear panel

■ Connecting antenna

■ Remote control

• The antenna should be stretched out.

• If radio reception is poor, change the height,

direction, or placement of the antenna.

• If you use an outdoor antenna instead of the

supplied FM antenna, reception will be better.

15V : Connect supplied

AC adaptor and power cable.

AUX: Connect an external

device. (☞ P. 7)

FM antenna terminal

(See below.)

ALARM TYPE switch (☞ P. 4)

CLOCK switch (☞ P. 4)

TONE CONTROL: Control Bass

and Treble.

Indoor FM antenna (supplied)

Notes

: System on/off

Source buttons: iPod,

AUX, RADIO

iPod control buttons

SLEEP: Sleep setting

(☞ P. 5)

ALARM: Alarm on/off

(☞ P. 4)

Battery insulation sheet:

Remove before using.

PRESET: Select the preset radio

station. (☞ P. 8)

VOLUME: Volume control

TUNING: Tuning radio

(☞ P. 8)

Infrared signal transmitter

4 En

OPERATION

This unit can play back iPod/radio and/or beep sound at the set time.

■ Setting the alarm time and sound

■ Switching the alarm on/off

BASIC FUNCTIONS

Adjusting the clock

1Set CLOCK to SET.

2 Set the time with TUNING.

3Set CLOCK to LOCK.

The time settings are lost approximately one

week after unplugging the unit.

Alarm setting

1Press SET.

2 Set the alarm time with

TUNING.

3Set ALARM TYPE.

• SOURCE+BEEP: selected source

(played back from 3 minutes before

the alarm time) and beep sound

(played back at the alarm time)

• SOURCE: selected source

• BEEP: beep sound only

When you select SOURCE+BEEP or

SOURCE, select:

• iPod: this unit resumes the song you

listened to last time.

• RADIO: this unit plays back the

radio station you listened to last time.

4 Set the alarm volume.

5Press SET.

Alarm is set and the alarm indicator

( ) lights up.

When iPod is selected as a source, set the iPod

to the charging cradle (☞ P. 2). If iPod is not

set at the alarm time, beep sound is played back.

Switch on/off the alarm function.

When the alarm is on, the alarm

indicator ( ) lights up and alarm

time is displayed for a while.

Rear panel Front panel display

flashes.

Note

Alarm indicator ( )

and front panel display

flashes.

Note

Rear panel (As required)

BASIC FUNCTIONS

5 En

English

At the set time, alarm sound plays back. During playback, operations below are available.

■ Using the snooze function

■ Stopping the alarm

You can set the time to turn off the system automatically when sleep is set to on.

You can set the countdown timer.

Operations during playing back alarm sound

Press SNOOZE/SLEEP.

The alarm sound stops and resumes

after 5 minutes.

Press ALARM or .

y

• Unless you stop the alarm, the alarm stops

after 60 minutes automatically.

• When you stop the alarm, the alarm time

setting, etc., is saved for convenient use next

time.

Sleep setting

Select the sleep time.

You can set 30, 60, 90 or 120 minutes.

When the sleep function is on, the

sleep indicator ( ) lights up.

y

To cancel the sleep, press SNOOZE/SLEEP.

Timer setting

1Press TIMER.

2 Set the countdown time with

TUNING.

You can set the time,

• 1 to 15 minutes: minute steps.

• 20 to 120 minutes: 10-minute steps.

3Press TIMER.

Countdown starts. When the timer

reaches 0, the timer sound plays back.

y

• To stop the timer sound, press TIMER.

• To cancel the timer, press TIMER during

countdown.

Sleep and timer cannot be used together.

• Sleep cannot be set during countdown.

• Sleep is set to off when timer is set while

sleep is on.

Sleep indicator ( ) and front

panel display flash.

Press repeatedly.

Front panel

display flashes.

Countdown

starts.

Note

6 En

For details on compatible iPod models, refer to “SPECIFICATIONS” (☞ P. 12).

■ Playing back

■ Status indicator of transmitter

y

The iPod indicator of SOURCE on the unit:

• lights up when wireless communication has been established.

• flashes if the status is other than above.

If cutting/no sound occurs, refer to “TROUBLESHOOTING” (☞ P. 10).

LISTENING TO iPod™ AND EXTERNAL SOURCES

Listening to your iPod™

1 Connect your iPod to the transmitter.

2 The status indicator blinks, and

wireless communication starts.

3Set SOURCE to iPod.

4 Play the iPod.

y

• You can remove the iPod whenever you want.

• When music/video in the iPod is played back, this unit

turns the system on automatically and plays back the

iPod even if the unit is system off.

• To charge the iPod, set the iPod to the charging cradle

on the unit (☞ P. 2).

• You can control the volume by the iPod.

• This unit turns the system off automatically after a

while if the iPod is turned off or removed from the

transmitter when SOURCE is set to iPod.

• If an iPod to be connected to the transmitter is playing

back, playback of iPod stops.

• When using a microwave oven, wireless LAN or

cordless telephone, etc., sound may be cut. Place the

unit away from these devices.

LED status The current status of the unit

Lights up green Wireless communication between the unit and transmitter is established.

Flashes green once Adjusting the volume level.

continuously Connection in progress, please wait.

Flashes red once The volume of this unit is set to maximum or minimum.

2 seconds An unsupported iPod is connected.

continuously Error occurs. Remove the iPod from the transmitter, and connect again.

Flashes red 2 times continuously The battery of the iPod is low.

Off An iPod is not connected or wireless communication has not been established.

Status indicator

Notes

iPod indicator

Note

LISTENING TO iPod™ AND EXTERNAL SOURCES

7 En

English

Connection between transmitter and unit is made by setting their group settings the same.

■ Group setting for the unit

■ Group setting for the transmitter

■ Playing back

Group setting

1Set SOURCE to iPod.

2 Press and hold MEMORY.

3 Set the group with TUNING.

Select A1, A2, A3, B1, B2 or B3.

B1/B2/B3 are displayed as b1/b2/b3 on

the front panel display.

4Press MEMORY.

Set the group selection switch.

Playing back external sources

1 Connect your portable audio

device to AUX using a

commercially available 3.5 mm

(1/8 in) mini plug cable.

Turn down the volume of this unit and your

portable audio device before connection.

2Set SOURCE to AUX.

3 Start playback on the

connected portable audio

device.

Press and hold.

Rear panel

Note

8 En

You can store your favorite radio stations with the preset function.

LISTENING TO RADIO STATIONS

Tuning radio stations

1Set SOURCE to RADIO.

2 For automatic tuning, press

and hold TUNING.

For manual tuning, press

TUNING repeatedly.

If you tune to a station manually, the sound

is monaural.

Presetting radio stations

1 Tune into a favorite radio

station.

2Press MEMORY.

3 Select the PRESET number

you want to store to.

y

To cancel the preset, press TUNING again.

4Press MEMORY to complete.

Selecting preset radio stations

1Set SOURCE to RADIO.

2 Select the preset radio station

with PRESET.

Note

9 En

English

ADDITIONAL INFORMATION

In case of a problem with the unit, check the following list first. If you cannot solve your problem with the

suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest

authorized Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Solution

The system turns on but

immediately shuts off.

The power cable may be connected

improperly.

Make sure the power cable is plugged into

the wall outlet firmly.

The unit may have received a strong

electrical shock such as lightning or

excessive static electricity.

Set the system to off, and disconnect the

power cable. Wait about 30 seconds,

reconnect the power cable, and turn on the

system.

The speakers make no

sound.

The volume may be set to the minimum

level.

Adjust the volume level.

The source may be incorrect. Select the correct source.

Sound suddenly turns off.

The sleep (☞ P. 5) may be set. Turn on the system and play the source

again.

The unit does not operate

properly.

The unit may have received a strong

electrical shock such as lightning or

excessive static electricity, or power

supply may have dropped.

Set the system to off, and disconnect the

power cable. Wait about 30 seconds,

reconnect the power cable, and turn on the

system.

A digital or high-frequency

equipment produces noises.

The unit may be placed too close to the

digital or high-frequency equipment.

Place the unit farther away from the

equipment.

The clock setting has been

cleared.

The unit is left more than one week after

you disconnect the power cable from the

wall outlet.

Plug the power cable into the wall outlet

firmly, and set the clock again

(☞ P. 4).

iPod does not play back at

the alarm time even if

SOURCE is set to iPod.

The iPod is not set to the charging cradle. Set the iPod to the charging cradle

(☞ P. 2).

ALARM TYPE is set to BEEP. Set ALARM TYPE to SOURCE+BEEP or

SOURCE (☞ P. 4).

Clock flashes and the unit

cannot be operated.

CLOCK on the rear panel is set to SET,

and this unit is in clock setting mode.

Set CLOCK to LOCK.

Sound is cracked/distorted

or there is abnormal noise.

Input source volume is excessive, or

volume of this unit is excessive

(especially Bass).

Adjust volume with VOLUME, or adjust

Bass with TONE CONTROL.

TROUBLESHOOTING

10 En

iPod™

Problem Cause Solution

The iPod does not charge up.

The iPod connecting to the transmitter is

set in the charging cradle improperly.

Remove the iPod connecting to the

transmitter from the unit, then set it in the

charging cradle again (☞ P. 2).

No sound

The iPod is not connected to the

transmitter firmly.

Connect the iPod firmly.

Earphones are connected. Remove the earphones.

Distance between the unit and the iPod is

too far.

Move the transmitter closer to the unit.

The battery of the iPod is low. Charge the iPod.

The iPod software version has not been

updated.

Download the latest iTunes software to

update the iPod software version to the

latest.

The iPod is in the process of connecting

with the unit.

Please wait for a while.

The unit and transmitter are not

connected since they are set to different

groups.

Set both the unit and transmitter to the same

group (☞ P. 7).

The unit is connected to another unit. Select a different group by changing the

group setting of the unit and transmitter

(☞ P. 7).

Cannot change the volume

by changing the volume of

the iPod.

– The iPod is not supported by this unit.

– The iPod is not connected correctly.

– The iPod software version is out of

date.

– The transmitter is connected to several

units.

– Use the supported iPod.

– Connect the iPod firmly.

– Update the iPod software version to the

latest.

If the problem cannot be solved, even the

latest software, reset the iPod.

– Change the group setting (☞ P. 7).

The iPod display does not

change by pressing the

remote control volume keys.

Suddenly the speaker

produces sound even though

an iPod is not connected.

The unit is connected to another

transmitter.

Change the group setting (☞ P. 7).

Transmitted sound is cut.

(Status indicator of

transmitter flashes green and

iPod indicator of SOURCE

on unit flashes.)

The signal from the transmitter is

blocked by your body or metallic objects,

etc.

Change the way of holding, the orientation,

or the position of the transmitter to avoid

your body or metallic objects blocking the

signal.

There is a device (microwave oven,

wireless LAN, cordless telephone, etc.)

outputting signals in the 2.4 GHz

frequency band nearby.

Place the unit away from these devices, or

turn them off. If the device is IEEE802.11n-

compliant, change the channel setting of the

device so as not to affect the unit.

If noise occurs at the same frequency the

transmitter is using, the unit will search

and move to another (unused) frequency,

which may cause sound to be cut.

This is not malfunction. If cut occurs

frequently, relocate the unit.

TROUBLESHOOTING

11 En

English

Radio reception

Problem Cause Solution

Too much noise during

stereo broadcast.

The FM antenna may be connected

improperly.

Make sure the FM antenna is connected

properly (☞ P. 3).

The radio station you selected may be far

from your area, or the radio wave

reception is weak in your area.

Try manual tuning to improve the signal

quality (☞ P. 8) or use a multi-channel

outdoor antenna.

Even with an outdoor

antenna, radio wave

reception is weak. (Sound is

distorted.)

Multipath reflection or other radio

interferences may have occurred.

Change the height, direction, or placement

of the antenna.

Remote control

Problem Cause Solution

The remote control does not

work properly.

The remote control may be operated

outside its operation range.

For information on the remote control

operation range, refer to “Using the remote

control” (☞ P. 1).

The remote control sensor on the unit

may be exposed to direct sunlight or

lighting (inverted fluorescent lamps).

Change the lighting or orientation of the

unit.

The battery may be worn out. Replace the battery with a new one

(☞ P. 1).

There are obstacles between the sensor of

the unit and the remote control.

Remove the obstacles.

Wireless communication is not

established when SOURCE is set to

iPod.

Play the iPod to establish wireless

communication (☞ P. 6).

12 En

■ PLAYER SECTION

iPod

• Supported iPod .... iPod (5th generation), iPod classic, iPod

nano, iPod touch, iPhone, iPhone 3G, iPhone 3GS

AUX IN

• Input connector

............STEREO L/R: 3.5 mm (1/8 in) STEREO mini Jack

■ AMPLIFIER SECTION

• Maximum output power ..........................4 W + 4 W + 8 W

(6 Ω 1 kHz, 10% THD)

• Driver unit .................. 4 cm (1 5/8 in) full-range driver × 2

5.5 cm (2 1/8 in) woofer + SR-BASS × 1

■ TUNER SECTION

• Tuning range

FM .................................................. 87.50 to 108.00 MHz

■ TRANSMITTER SECTION

• Frequency ............................................................... 2.4 GHz

• Transmission range.......................... Approx. 20 m (65.6 ft)

(without interference)

• Number of units which can be simultaneously transmitted

to......................................................................Up to 7 units

(depending on the circumstances)

■ GENERAL

• Power Supply........................... AC 100 to 240 V, 50/60 Hz

• Power consumption......................................................10 W

• System off consumption .............................................3.5 W

• Standby consumption...................................... 1.0 W or less

• Dimensions (W × H × D)...................260 × 90.3 × 141 mm

(10 1/4 × 3 1/2 × 5 1/2 in)

• Weight.........................................................1.2 kg (2.6 lbs.)

Specifications are subject to change without notice.

iPod™, iPhone™

iPod is a trademark of Apple Inc., registered in the U.S. and

other countries.

iPhone is a trademark of Apple Inc.

“Made for iPod” means that an electronic accessory has been

designed to connect specifically to iPod and has been

certified by the developer to meet Apple performance

standards.

“Works with iPhone” means that an electronic accessory has

been designed to connect specifically to iPhone and has been

certified by the developer to meet Apple performance

standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

SPECIFICATIONS

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth

terminal of the three pin plug.

13 En

English

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service,

please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative

office in your country. You can find full details on our website (http://www.yamaha-hifi.com/ or http://www.yamaha-

uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the

original purchase. Yamaha undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired,

or replaced at Yamaha’s discretion, without any charge for parts or labour. Yamaha reserves the right to replace a product with

that of a similar kind and/or value and condition, where a model has been discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the

defective product, along with a statement detailing the fault. In the absence of this clear proof of purchase, Yamaha

reserves the right to refuse to provide free of charge service and the product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area

(EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the

customer’s responsibility to ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with

Yamaha’s instructions on the proper use, maintenance and storage, and (b) installation or use of the product in a

manner inconsistent with the technical or safety standards in force in the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to

the technical or safety standards of the country of use and/or to the standard specification of a product sold by

Yamaha in the EEA and/or Switzerland.

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the

country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the

repair or replacement of the product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such

settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s

rights against the dealer arising from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment

and Used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC

and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent

any potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

i Fr

1 Pour utiliser l’appareil au mieux de ses possibilités,

lisez attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

2 Installez cet appareil dans un endroit frais, bien aéré,

sec et propre - à l’abri de la lumière du soleil, des

sources de chaleur, des vibrations, des poussières, de

l’humidité et du froid. Pour une aération correcte,

tenez compte des distances minimales suivantes.

Au-dessus : 15 cm

À l’arrière : 10 cm

Sur les côtés : 10 cm

3 Placez l’appareil loin des équipements, moteurs et

transformateurs électriques, pour éviter les

ronflements parasites.

4 N’exposez pas l’appareil à des variations brutales de

température, ne le placez pas dans un environnement

très humide (par exemple dans une pièce contenant

un humidificateur) car cela peut entraîner la

condensation d’humidité à l’intérieur de l’appareil

qui elle-même peut être responsable de décharge

électrique, d’incendie, de dommage à l’appareil ou de

blessure corporelle.

5

Evitez d’installer l’appareil dans un endroit où des

objets peuvent tomber, ainsi que là où l’appareil pourrait

être exposé à des éclaboussures ou des gouttes d’eau.

Sur le dessus de l’appareil, ne placez pas :

– d’autres appareils qui peuvent endommager la

surface de l’appareil ou provoquer sa décoloration.

– des objets se consumant (par exemple, une bougie)

qui peuvent être responsables d’incendie, de

dommage à l’appareil ou de blessure corporelle.

– des récipients contenant des liquides qui peuvent

être à l’origine de décharge électrique ou de

dommage à l’appareil.

6

Ne couvrez pas l’appareil d’un journal, d’une nappe,

d’un rideau, etc. car cela empêcherait l’évacuation de la

chaleur. Toute augmentation de la température

intérieure de l’appareil peut être responsable d’incendie,

de dommage à l’appareil ou de blessure corporelle.

7 Ne branchez pas la fiche du câble d’alimentation de

l’appareil sur une prise secteur aussi longtemps que

tous les raccordements n’ont pas été effectués.

8 Ne pas faire fonctionner l’appareil à l’envers. Il

risquerait de chauffer et d’être endommagé.

9 N’exercez aucune force excessive sur les

commutateurs, les boutons et les cordons.

10 Pour débrancher la fiche du câble d’alimentation au

niveau de la prise secteur, saisissez la fiche et ne tirez

pas sur le cordon.

11 Ne nettoyez pas l’appareil au moyen d’un solvant

chimique, ce qui pourrait endommager la finition.

Utilisez un chiffon sec et propre.

12 N’alimentez l’appareil qu’à partir de la tension

prescrite. Alimenter l’appareil sous une tension plus

élevée est dangereux et peut être responsable

d’incendie, de dommage à l’appareil ou de blessure

corporelle. Yamaha ne saurait être tenue responsable

des dommages résultant de l’alimentation de

l’appareil sous une tension autre que celle prescrite.

13 Pour empêcher tout dommage causé par les éclairs,

déconnectez la câble d’alimentation et toute antenne

extérieure de la prise murale pendant un orage.

14 Ne tentez pas de modifier ni de réparer l’appareil.

Consultez le service Yamaha compétent pour toute

réparation qui serait requise. Le coffret de l’appareil

ne doit jamais être ouvert, quelle que soit la raison.

15 Si vous envisagez de ne pas vous servir de l’appareil

pendant une longue période (par exemple, pendant

les vacances), débranchez la fiche du câble

d’alimentation au niveau de la prise secteur.

16 Lisez la section intitulée « GUIDE DE

DÉPANNAGE » où figurent une liste d’erreurs de

manipulation communes avant de conclure que

l’appareil présente une anomalie de fonctionnement.

17 Avant de déplacer l’appareil, appuyez sur pour

éteindre le système puis débranchez la fiche du câble

d’alimentation au niveau de la prise secteur.

18

La condensation se forme lorsque la température ambiante

change brusquement. En ce cas, débranchez la fiche du

câble d’alimentation et laissez l’appareil reposer.

19

La température de l’appareil peut augmenter en raison d’une

utilisation prolongée. En ce cas, coupez l’alimentation de

l’appareil et laissez-le au repos pour qu’il refroidisse.

20 Installez cet appareil à proximité de la prise secteur et

à un emplacement où la fiche du câble d’alimentation

est facilement accessible.

21

Les piles ne doivent pas être exposées à une chaleur extrême,

par exemple au soleil, à une flamme, etc. Lors de la mise au

rebut des piles, suivez vos réglementations locales.

22 Utilisez l’adaptateur secteur fourni avec cet appareil.

L’emploi de tout autre adaptateur secteur peut causer

un incendie ou endommager l’appareil.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER

L’APPAREIL.

Cet appareil n’est pas déconnecté du secteur tant qu’il reste

branché à la prise de courant, même si l’appareil en soi est

éteint par la touche . Dans cet état, l’appareil consomme

une très faible quantité de courant.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET

APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

ATTENTION

Danger d’explosion si la pile n’est pas remplacée correctement.

La remplacer par une pile de type identique ou équivalent.

Ne pas utiliser cet appareil à moins de 22 cm de personnes

ayant un stimulateur cardiaque ou un défibrillateur.

Nous, le fabricant Yamaha, déclarons que le TSX-W80 est

conforme aux exigences essentielles et aux autres

dispositions pertinentes de la Directive 1999/5/EC.

Il y a un risque possible de création d’interférences,

visibles sur les images en couleurs si cet appareil est placé

à côté d’un téléviseur à tube cathodique (tube de Braun).

Dans ce cas, éloigner l’unité du téléviseur.

1 Fr

Français

PREPARATION

NOM DES PARTIES ET LEURS FONCTIONS

..................................................................................2

FONCTIONS DE BASE.........................................4

ÉCOUTE DE L’iPod™ ET DE SOURCES

EXTERNES.............................................................6

ÉCOUTE DES STATIONS RADIO..................... 8

GUIDE DE DÉPANNAGE.................................... 9

CARACTÉRISTIQUES TECHNIQUES........... 12

■ Caractéristiques

– Lecture de haute qualité d’un iPod/d'un iPhone, de la radio et de dispositifs audio externes.

– Son grave ferme et son stéréo spacieux depuis haut-parleur à 2.1 canaux (tweeter × 2, haut-parleur de

graves × 1), SR-Bass™ (technologie Yamaha Swing Radiator Bass) et DSP dans un appareil compact.

– Interface à boutons facile et intuitive pour l’utilisateur avec DEL guides et molettes.

■ Yamaha AirWired

Transfert de musique non compressée en temps réel sans perte de qualité sonore grâce à AirWired, la

technologie originale de transfert digital sans fil de Yamaha. Vous pouvez également allumer/éteindre le

système et le volume avec votre iPod via AirWired.

y

Vous pouvez utiliser un caisson de graves sans fil grâce à l’Ensemble de caissons de sous-graves sans fil (SWK-W10, etc.,

vendu séparément). Pour plus de détails, voir le mode d’emploi du SWK-W10.

■ Quelques mots sur ce mode d’emploi

• Cet appareil est compatible avec l’iPod ainsi que l’iPhone. « iPod » indiqué dans ce manuel peut

également faire référence à « iPhone ».

• Ce mode d’emploi indique comment faire fonctionner cet appareil en utilisant les boutons sur l’appareil.

Certaines de ces fonctions sont également disponibles en utilisant la télécommande.

■ Accessoires fournis

■ Utilisation de la télécommande ■ Remplacement de la pile de la

télécommande

TABLE DES MATIÈRES

Télécommande Adaptateur

secteur

Cordon

d’alimentation

Émetteur Antenne intérieure FM

(CC 15 V, 2,66 A,

numéro de modèle :

NU40-2150266-I3)

YIT-W11TX

À moins de 6 m

Pile

CR2025

2 Fr

■ Panneau avant et supérieur

1 : Appuyez pour allumer/éteindre le système.

L’heure est affichée même lorsque le système est

éteint.

y

• Appuyez et maintenez sur la partie supérieure de

l’appareil pendant plus de 3 secondes pour mettre le

système en mode veille. Toutes les informations de

l’afficheur ne s’affichent pas en mode veille. Cela peut

réduire la consommation d’électricité. Pour annuler le

mode veille, appuyez sur .

• Si le système est éteint/en mode veille, la fonction

d’alarme est disponible.

2 TIMER : Réglage de la minuterie (☞ P. 5)

3 ALARM : Alarme activée/désactivée (☞ P. 4)

4 SET : Paramètres de l’alarme (☞ P. 4)

5 Afficheur

6 SOURCE : iPod, AUX, RADIO

7 VOLUME : Réglage du volume

8 PRESET : Mémorisation de vos 5 stations radio

favorites (☞ P. 8)

9 SNOOZE/SLEEP (☞ P. 5)

0 DIMMER : Réglage de la luminosité de l’afficheur

A (auto) 3 (le plus lumineux) 2 1 (le plus

sombre) retour à A

y

Lorsque réglé sur A (auto), la luminosité de l’afficheur

s’ajuste automatiquement en fonction de la luminosité de

la chambre.

A MEMORY (☞ P. 7, ☞ P. 8)

B TUNING (☞ P. 8)

C Support de chargement : Pour charger un iPod

D Capteur d’illumination : Mesure le niveau

d’illumination ambiante. Ne pas couvrir ce capteur.

NOM DES PARTIES ET LEURS FONCTIONS

Lors du chargement d’un iPod,

1 Connectez l’iPod à l’émetteur.

2 Placez l’iPod connecté à l’émetteur dans le

support de chargement.

NOM DES PARTIES ET LEURS FONCTIONS

3 Fr

Français

■ Panneau arrière

■ Branchement antenne

■ Télécommande

• L’antenne doit être déployée.

• Si la réception de la radio est mauvaise,

changez la hauteur, le sens ou la disposition

de l’antenne.

• Si vous utilisez une antenne extérieure au lieu

de l’antenne FM fournie, la réception sera

meilleure.

15V : Branchez l’adaptateur

secteur fourni et le cordon

d’alimentation

AUX : Branchez un

dispositif audio externe.

(☞ P. 7)

Borne d’antenne FM

(voir ci-dessous.)

Commutateur ALARM TYPE (☞ P. 4)

Commutateur CLOCK (☞ P. 4)

TONE CONTROL : Contrôle

des graves et des aigus.

Antenne intérieure FM (fournie)

Remarques

: Allumer/éteindre système

Touches de sélection de

source : iPod, AUX, RADIO

Touches de réglage iPod

SLEEP : Réglage de la mise

en veille (☞ P. 5)

ALARM : Alarme activée/

désactivée (☞ P. 4)

Feuille isolante de la pile :

retirer avant usage.

PRESET : Sélectionnez la station

radio présélectionnée. (☞ P. 8)

VOLUME : Réglage du volume

TUNING : Syntonisation

de la radio (☞ P. 8)

Transmetteur de signaux

infrarouges

4 Fr

OPERATION

Cet appareil peut lire l’iPod/la radio et/ou faire retentir le bip à l’heure que vous avez définie.

■ Réglage de l’alarme et du son

■ Activer/désactiver l’alarme

FONCTIONS DE BASE

Réglage de l’horloge

1Réglez CLOCK sur SET.

2 Réglez l’heure avec TUNING.

3Réglez CLOCK sur LOCK.

Les paramètres de l’heure se perdent après plus ou

moins une semaine après avoir débranché l’appareil.

Panneau

arrière

L’afficheur clignote.

Remarque

Réglage de l’alarme

1 Appuyez sur SET.

2 Réglez l’heure d’alarme avec

TUNING.

3Réglez ALARM TYPE.

• SOURCE+BEEP : source

sélectionnée (lue jusqu’à 3 minutes

avant l’heure d’alarme) et bip sonore

(lu à l’heure d’alarme)

• SOURCE : source sélectionnée

• BEEP : uniquement bip sonore

Lorsque vous sélectionnez SOURCE+BEEP

ou SOURCE, sélectionnez :

• iPod : cet appareil continue la lecture

de la chanson que vous écoutiez la

dernière fois.

• RADIO : cet appareil lit la station radio

que vous écoutiez la dernière fois.

4 Réglez le volume de l’alarme.

5 Appuyez sur SET.

L’alarme est réglée et l’indicateur

d’alarme ( ) s’illumine.

Lorsqu’iPod est sélectionné en tant que source,

placez l’iPod dans le support de chargement

(☞ P. 2). Si l’iPod n’est pas placé au moment

de l’alarme, vous entendrez le bip sonore.

Activer/désactiver la fonction

d’alarme.

Lorsque l’alarme est activée, l’indicateur

d’alarme ( ) s’allume et l’heure

d’alarme s’affiche pendant un moment.

L’indicateur d’alarme

( ) et l’afficheur

clignotent.

Remarque

Panneau arrière (comme souhaité)

Sayfa yükleniyor ...

YAMADA TSX-W80LB El kitabı

Bu kılavuz için de uygundur

YAMADA TSX-W80LB El kitabı

Diğer dillerde

Diğer Belgeler