Panasonic KXTG7150FX Kullanma talimatları

This unit is Caller ID compatible. To display the caller’s phone

number, you must subscribe to Caller ID service.

Charge the batteries for about 7 hours before initial use.

Please read these operating instructions before using the unit and save them for

future reference.

(For Czech and Slovakia)

This cordless telephone is possible to use according to General licence No.: VO-

R/8/08.2005-23 (for Czech), VPR-7/2001 (for Slovakia).

Operating Instructions

Model No. KX-TG7150FX

KX-TG7170FX

Digital Cordless Phone

KX-TG7150

Contents/Obsah/İçindekiler

English instructions

Türkçe talimatlar

Appendix/Dodatek/Príloha/Ek

Page/Strana/Str./Sayfa

1

–

36

(1)

–

(36)

<1>

–

<36>

((1))

–

((36))

[1]

–

[8]

Pokyny v češtině

Pokyny v slovenčine

TG7150-7170FX(e).book Page 1 Wednesday, January 10, 2007 3:32 PM

Introduction

2

Introduction

Thank you for purchasing a new Panasonic digital cordless phone.

For your future reference

Attach or keep original receipt to assist with any repair under warranty.

Note:

L In the event of problems, you should contact your equipment supplier in the first instance.

Declaration of Conformity:

L Panasonic Communications Co., Ltd. declares that this equipment is in compliance with the

essential requirements and other relevant provisions of Radio & Telecommunications

Terminal Equipment (R&TTE) Directive 1999/5/EC.

Declarations of Conformity for the relevant Panasonic products described in this manual

are available for download by visiting:

http://www.doc.panasonic.de

Contact:

Panasonic Services Europe

a Division of Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Your phone

Note:

L The handsets have been pre-registered for use with their base unit. If not registered, see

page 24.

Serial No. (found on the bottom of the base unit)

Date of purchase

Name and address of dealer

KX-TG7150

(Big button type

handset)

KX-TG7170

(Bone conduction

type handset)

TG7150-7170FX(e).book Page 2 Wednesday, January 10, 2007 3:32 PM

Table of Contents

3

Preparation

Accessory information . . . . . . . . . . . . . . . 4

Expanding your phone system. . . . . . . . . 5

Important information. . . . . . . . . . . . . . . . 6

Bone conduction earpiece (KX-TG7170

only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Displays . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connections. . . . . . . . . . . . . . . . . . . . . . . 9

Battery installation/replacement. . . . . . . 10

Battery charge . . . . . . . . . . . . . . . . . . . . 10

Turning the power on/off . . . . . . . . . . . . 11

Symbols used in these operating

instructions. . . . . . . . . . . . . . . . . . . . . . . 11

Display language . . . . . . . . . . . . . . . . . . 11

Dialling mode (tone/pulse) . . . . . . . . . . . 12

Date and time . . . . . . . . . . . . . . . . . . . . 12

Accessibility features

Talking number display (Voice

announce) . . . . . . . . . . . . . . . . . . . . . . . 13

Making/Answering Calls

Making calls . . . . . . . . . . . . . . . . . . . . . . 14

Answering calls . . . . . . . . . . . . . . . . . . . 15

Phonebook

Handset phonebook. . . . . . . . . . . . . . . . 16

Chain dial. . . . . . . . . . . . . . . . . . . . . . . . 17

Handset Settings

Handset settings . . . . . . . . . . . . . . . . . . 18

Time settings . . . . . . . . . . . . . . . . . . . . . 20

Base Unit Settings

Base unit settings . . . . . . . . . . . . . . . . . 21

Caller ID Service

Using Caller ID service . . . . . . . . . . . . . 22

Caller list . . . . . . . . . . . . . . . . . . . . . . . . 22

Voice mail service . . . . . . . . . . . . . . . . . 23

Multi-unit Operation

Operating additional units . . . . . . . . . . . 24

Registering a handset to the base unit . 24

Intercom between handsets . . . . . . . . . 25

Transferring calls between handsets. . . 26

Copying phonebook entries. . . . . . . . . . 26

Useful Information

Using the belt clip . . . . . . . . . . . . . . . . . 27

Using the shoulder rest attachment . . . . 27

Character entry . . . . . . . . . . . . . . . . . . . 28

Error messages . . . . . . . . . . . . . . . . . . . 30

Troubleshooting . . . . . . . . . . . . . . . . . . . 30

Specifications. . . . . . . . . . . . . . . . . . . . . 33

Index

Index . . . . . . . . . . . . . . . . . . . . . . . . . . 34

TG7150-7170FX(e).book Page 3 Wednesday, January 10, 2007 3:32 PM

Preparation

4

Accessory information

Included accessories

*1 The handset cover comes attached to the handset.

Additional/replacement accessories

Please contact your nearest Panasonic dealer for sales information.

Note:

L You can expand your phone system by registering additional compatible Panasonic

handsets (page 5).

L When replacing the batteries, use only 2 rechargeable AAA (R03) size nickel metal hydride

(Ni-MH) batteries of capacity up to 750 mAh. We recommend using Panasonic

rechargeable batteries (Model No. P03P).

L We cannot be responsible for any damage to the unit or degradation of performance which

may occur from using non-Panasonic rechargeable batteries.

No. Accessory items Quantity

1 AC adaptor for base unit (Part No. PQLV207CE) 1

2 Telephone line cord 1

3 Rechargeable batteries AAA (R03) size

(Part No. HHR-55AAAB or HHR-4EPT)

2

4 Handset cover

*1

1

5 Belt clip 1

6 Shoulder rest 1

123456

No. Model No. Description

1 KX-TCA717EX Wall-Mounting Adaptor

2 KX-TCA94EX Headset

3 KX-A272 DECT repeater

12

TG7150-7170FX(e).book Page 4 Wednesday, January 10, 2007 3:32 PM

Preparation

5

Expanding your phone system

You can expand your phone system by registering the following optional handsets to a single

base unit (KX-TG7150 or KX-TG7170): max. 6

Please contact your nearest Panasonic dealer for sales information.

Handset feature overview for KX-TGA711, KX-TGA715, and KX-TGA717

Operations and features of the 3 different accessory handsets have certain differences as

indicated in the table below.

Handsets: max. 6

Additional digital

cordless handset

Turkey:

KX-TGA711EX

Other countries:

KX-TGA711FX

Additional digital

cordless handset

KX-TGA715FX

(Big button type

handset)

Additional digital

cordless handset

KX-TGA717FX

(Bone conduction

type handset)

Feature KX-TGA711 KX-TGA715 KX-TGA717 Page

Description Available as

accessory

handset only

Same handset

supplied with

KX-TG7150

Same handset

supplied with

KX-TG7170

—

Big button — rr—

Bone conduction

earpiece

——r page 7

Call restriction r ———

Headset jack — rrpage 8

Voice announce — rrpage 13

TG7150-7170FX(e).book Page 5 Wednesday, January 10, 2007 3:32 PM

Preparation

6

Important information

General

L Use only the AC adaptor included with this

product, noted on page 4.

L Do not connect the AC adaptor to any AC

outlet other than a standard 220–240 V

AC outlet.

L This product is unable to make calls when:

– the portable handset battery(ies) need

recharging or have failed.

– there is a power failure.

L Do not open the base unit, charger, or

handset other than to replace the

battery(ies).

L This product should not be used near

emergency/intensive care medical

equipment and should not be used by

people with pacemakers.

L Care should be taken that objects do not

fall onto, and liquids are not spilled into,

the unit. Do not subject this product to

excessive smoke, dust, mechanical

vibration or shock.

Environment

L Do not use this product near water.

L This product should be kept away from

heat sources such as radiators, cookers,

etc. It should also not be placed in rooms

where the temperature is less than 5 °C or

greater than 40 °C.

L The AC adaptor is used as the main

disconnect device. Ensure that the AC

outlet is installed near the product and is

easily accessible.

Warning:

L To prevent the risk of electrical shock, do

not expose this product to rain or any

other type of moisture.

L Unplug this product from power outlets if it

emits smoke, an abnormal smell, or

makes unusual noise. These conditions

can cause fire or electric shock. Confirm

that smoke has stopped emitting and

contact an authorised service centre.

L Do not spill liquids (detergents, cleansers,

etc.) onto the telephone line cord plug, or

allow it to become wet at all. This may

cause a fire. If the telephone line cord plug

becomes wet, immediately pull it from the

telephone wall jack, and do not use.

Battery caution

L We recommend using the battery(ies)

noted on page 4. Use only rechargeable

battery(ies).

L Do not mix old and new batteries.

L Do not dispose of the battery(ies) in a fire,

as they may explode. Check with local

waste management codes for special

disposal instructions.

L Do not open or mutilate the battery(ies).

Released electrolyte from the battery(ies)

is corrosive and may cause burns or injury

to the eyes or skin. The electrolyte may be

toxic if swallowed.

L Exercise care when handling the

battery(ies). Do not allow conductive

materials such as rings, bracelets or keys

to touch the battery(ies), otherwise a short

circuit may cause the battery(ies) and/or

the conductive material to overheat and

cause burns.

L Charge the battery(ies) in accordance

with the information provided in these

operating instructions.

L Only use the included base unit (or

charger) to charge the battery(ies). Do not

tamper with the base unit (or charger).

Failure to follow these instructions may

cause the battery(ies) to swell or explode.

TG7150-7170FX(e).book Page 6 Wednesday, January 10, 2007 3:32 PM

Preparation

7

Information on Disposal for Users of

Waste Electrical & Electronic Equipment

(private households)

This symbol on the products and/or

accompanying documents means that used

electrical and electronic products should not

be mixed with general household waste. For

proper treatment, recovery and recycling,

please take these products to designated

collection points, where they will be

accepted on a free of charge basis.

Alternatively, in some countries you may be

able to return your products to your local

retailer upon the purchase of an equivalent

new product.

Disposing of this product correctly will help

to save valuable resources and prevent any

potential negative effects on human health

and the environment which could otherwise

arise from inappropriate waste handling.

Please contact your local authority for

further details of your nearest designated

collection point.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

For business users in the European

Union

If you wish to discard electrical and

electronic equipment, please contact your

dealer or supplier for further information.

Information on Disposal in other

Countries outside the European Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please

contact your local authorities or dealer and

ask for the correct method of disposal.

Bone conduction earpiece

(KX-TG7170 only)

The handset features a bone conduction

earpiece that uses vibrations to create

sound during your telephone conversations.

For proper operation press the bone

conduction earpiece against your face near

the ear.

Normally, sound enters the ear canal and

vibrates the eardrum. People feel the

vibration within the inner ear and

comprehend it as it is received by the

auditory nerve.

Place the bone conduction earpiece against

your face (not your ear). Try different

locations to find which location works best.

Start with the temple area.

Note:

L Do not place the bone conduction

earpiece on a hearing aid. Howling or

other interference may be heard.

External ear

Middle ear

Inner ear

Auditory

nerve

Sound

Bone

conduction

earpiece

TG7150-7170FX(e).book Page 7 Wednesday, January 10, 2007 3:32 PM

Preparation

8

L The effectiveness of the bone conduction

earpiece will vary by the type and degree

of hearing loss of the user.

L As sound is generated by vibration, users

with normal hearing can use the handset

by placing the bone conduction earpiece

against the ear, as an ordinary telephone.

L If the bone conduction earpiece gets dusty

or greasy, clean it with a soft, dry cloth.

Controls

Handset (KX-TG7150)

Handset (KX-TG7170)

A Speaker

B Charge contact

C Headset jack

D {j/OK} (Menu/OK)

E {k} (Phonebook)

F {C} (Talk)

G Navigator key ({^}/{V}/{>}/{<})

H {s} (Speakerphone)

I {R} (Recall)

J Charge indicator/Ringer indicator

K KX-TG7150

Receiver

KX-TG7170

Bone conduction earpiece

L Display

M {R} (Redial/Pause)

N {ih} (Off/Power)

O {C/T} (Clear/Mute)

P Dial keypad

Q {INT} (Intercom)

R Microphone

Base unit

A Charge contact

B {x} (Page)

C Ringer

N

B

A

O

P

Q

R

L

K

M

F

G

I

H

J

D

C

E

B

A

N

O

Q

R

L

K

M

F

G

I

H

J

D

C

E

P

A B

C

TG7150-7170FX(e).book Page 8 Wednesday, January 10, 2007 3:32 PM

Preparation

9

Displays

Display icons

*1 Voice mail users only

Connections

When connecting the AC adaptor to the

base unit, a short beep will be heard. If it is

not heard, check the connections.

Note:

L Never install telephone wiring during a

lightning storm.

L The AC adaptor must remain connected

at all times. (It is normal for the adaptor to

feel warm during use.)

L The AC adaptor should be connected to a

vertically oriented or floor-mounted AC

outlet. Do not connect the AC adaptor to a

ceiling-mounted AC outlet, as the weight

of the adaptor may cause it to become

disconnected.

Location

L For maximum distance and noise-free

operation, place your base unit:

– away from electrical appliances such as

TVs, radios, personal computers or

other phones.

– in a convenient, high and central

location.

Display

icon

Meaning

w Within range of a base unit

L When flashing: Handset

is searching for base unit.

(out of range of base unit,

handset is not registered

to base unit, no power on

base unit)

L Handset is accessing base

unit. (intercom, paging,

changing base unit

settings, etc.)

k Handset is on an outside

call.

5 Battery strength

[2] Handset number (Standby

display setting, page 18)

0 New voice mail message

received

*1

(page 23)

Line is being used by

another handset.

Use only the included AC

adaptor and telephone

line cord.

(220–240 V, 50 Hz)

To telephone

network

Hook

TG7150-7170FX(e).book Page 9 Wednesday, January 10, 2007 3:32 PM

Preparation

10

Battery

installation/replacement

Important:

L Use only the included rechargeable

batteries noted on page 4, 6.

L When replacing batteries, we recommend

using the Panasonic rechargeable

batteries noted on page 4, 6.

L Wipe the battery ends (S, T) with a dry

cloth.

L When installing the batteries, avoid

touching the battery ends (S, T) or the

unit contacts.

1 Press the notch on the handset cover

firmly and slide it in the direction of the

arrow.

L When replacing batteries, remove the

old batteries positive (S) end first.

2 Insert the batteries negative (T) end

first. Close the handset cover.

Battery charge

Place the handset on the base unit for

about 7 hours before initial use.

When charging, the battery icon is shown as

follows.

When the batteries are fully charged, 5

remains on the display.

L The charge indicator lights up when the

handset is placed on the base unit.

L The pictured model is KX-TG7150.

Note:

L It is normal for the handset to feel warm

during charging.

L If you want to use the unit immediately,

charge the batteries for at least 15

minutes.

L Clean the charge contacts of the handset

and base unit with a soft, dry cloth once a

month, otherwise the batteries may not

charge properly. Clean more often if the

unit is exposed to grease, dust, or high

humidity.

Charge

contact

TG7150-7170FX(e).book Page 10 Wednesday, January 10, 2007 3:32 PM

Preparation

11

Battery strength

Panasonic Ni-MH battery performance

(included batteries)

Note:

L It is normal for batteries not to reach full

capacity at the initial charge. Maximum

battery performance is reached after a few

complete cycles of charge/discharge

(use).

L Actual battery performance depends on a

combination of how often the handset is in

use and how often it is not in use

(standby).

L Battery operating time may be shortened

over time depending on usage conditions

and ambient temperature.

L Even after the handset is fully charged,

the handset can be left on the base unit

without any ill effect on the batteries.

L The battery strength may not be displayed

correctly after you replace the batteries. In

this case, place the handset on the base

unit and charge for at least 7 hours.

Turning the power on/off

Power on

Press {ih} for about 1 second.

Power off

Press {ih} for about 2 seconds.

Symbols used in these

operating instructions

Display language

17 display languages are available.

1 {ih} i {j/OK}

2 Press {^} or {V} to select “Handset

Setup”. i {>}

3 Press {^} or {V} to select “Display

Setup”. i {>}

4 Press {^} or {V} to select “Select

Language”. i {>}

Battery icon Battery strength

5 High

6 Medium

7 Low

When flashing: Needs

to be charged.

Operation Operating time

In continuous use KX-TG7150:

12 hours max.

KX-TG7170:

10 hours max.

In continuous

standby mode

150 hours max.

Symbol Meaning

{j/OK} Press {j/OK}.

i Proceed to the next operation.

“ ” Select the words in quotations

shown on the display (e.g.,

“Handset Setup”) by

pressing {^} or {V}.

You can select

“Deutsch

Deutsch

”,

,

“English

English

”,

,

“Türk

rk

çe”,

,

“Magyar

Magyar

”,

,

“Polski

Polski

”,

“slovensky

slovensky

”, “ČeŠtina

tina

”,

,

“Hrvatski

Hrvatski

”,

,

“Slovenscina

Slovenscina

”,

,

“Eesti

Eesti

”,

“LIETUVI

LIETUVI

ŠKAI

KAI

”,

,

“Latvie

Latvie

Šu”,

,

“Rom

Rom

ânã”,

,

“БЪЛГАРСКИ

БЪЛГАРСКИ

”,

,

“Srpski

Srpski

”,

“МАКЕДОНСКИ

МАКЕДОНСКИ

”, or

, or

“Shqiptar

Shqiptar

”.

TG7150-7170FX(e).book Page 11 Wednesday, January 10, 2007 3:32 PM

Preparation

12

5 Press {^} or {V} to select the desired

language. i {>} i {ih}

Note:

L If you select a language you cannot read,

press {ih}, press {j/OK} , press {^} 3

times, press {>}, press {V} 2 times, press

{>}, press {V}, press {>}, select the

desired language, press {>}, then press

{ih}.

L To change the voice announce language,

see page 13.

Dialling mode (tone/pulse)

Changing the dialling mode depending on

your telephone line service.

“Tone”: Select when you have a touch tone

service.

“Pulse”: Select when you have rotary or

pulse service.

1 {j/OK}

2 Press {^} or {V} to select “Base Unit

Setup”. i {>}

3 Press {^} or {V} to select “Call

Options”. i {>}

4 Press {^} or {V} to select “Dial Mode”.

i {>}

5 Press {^} or {V} to select the desired

setting. i {>} i {ih}

Date and time

1 {j/OK}

2 Press {^} or {V} to select “Handset

Setup”. i {>}

3 Press {^} or {V} to select “Time

Settings”. i {>}

4 Press {^} or {V} to select “Set Date &

Time”. i {>}

5 Enter the current day, month, and year.

Example: 17 May, 2006

{1}{7} {0}{5} {0}{6}

6 Enter the current hour and minute.

Example: 3:30 PM

{0}{3} {3}{0} i Press {*} until

“03:30 PM” is displayed.

7 {j/OK} i {ih}

Note:

L To correct a digit, press {<} or {>} to

move the cursor to the digit, then make

the correction.

L The date and time may be incorrect after a

power failure. In this case, set the date

and time again.

TG7150-7170FX(e).book Page 12 Wednesday, January 10, 2007 3:32 PM

Accessibility features

13

Talking number display

(Voice announce)

The voice announce features allow the

handset to announce displayed phone

number. (Caller ID announce/List

announce)

Caller ID announce

When you receive an outside call which has

phone number information, the handset

announces the displayed phone number

from the handset speaker.

L To announce outside caller’s phone

number, you must first subscribe to Caller

ID service (page 22).

L The announcement is heard at the ringer

volume (page 18).

List announce

The handset announces phone numbers

from the handset speaker while you are

viewing the redial list, caller list, and

phonebook.

L If the displayed phone number has a

P(pause), the handset inserts a 0.5

second pause for each P and if the

number has the other symbols, (for

example, ;, #, etc.) the handset skips the

symbols and announces the next number.

Setting volume for voice

announce

You can set the volume for list announce.

The volume for caller ID announce is set

when setting the ringer volume on page 18.

1 {j/OK}

2 “Handset Setup” i {>}

3 “Other Options” i {>}

4 “Voice Announce” i {>}

5 “Volume” i {>}

6 Select the desired volume.

L To turn the voice announce feature off,

select the volume “Off”.

7 {>} i {ih}

Note:

L The caller ID announce is heard at the

handset ringer volume (page 18). When

the volume for voice announce is set to

“Off”, the handset does not announce

the phone number regardless of the ringer

volume.

Selecting language for voice

announce

6 voice announce languages are available.

1 {j/OK}

2 “Handset Setup” i {>}

3 “Other Options” i {>}

4 “Voice Announce” i {>}

5 “Select Language” i {>}

6 Select the desired language. i {>}

i {ih}

Note:

L To change the display language, see page

11.

You can select

“English

English

”,

,

“Türk

rk

çe”,

,

“Magyar

Magyar

”,

,

“Polski

Polski

”, “slovensky

slovensky

”,

,

or

“ČeŠtina

tina

”.

TG7150-7170FX(e).book Page 13 Wednesday, January 10, 2007 3:32 PM

Making/Answering Calls

14

Making calls

1 Lift the handset and dial the phone

number.

L To correct a digit, press {C/T}, then

enter the correct number.

2 {C}

3 When finished talking, press {ih} or

place the handset on the base unit.

Speakerphone

1 During a conversation, press {s} to turn

on the speakerphone.

L Speak alternately with the caller.

2 When finished talking, press {ih}.

Note:

L For best performance, use the

speakerphone in a quiet environment.

L To switch back to the receiver, press

{C}.

To adjust the receiver or speaker volume

Press {^} or {V} while on a call.

Redial feature

Previously dialled phone numbers (each 24

digits max.) can be redialled.

To make a call using the redial list

The last 10 phone numbers dialled are

stored in the redial list.

1 {R}

2 Press {^} or {V} to select the desired

number.

3 {C} / {s}

To erase numbers in the redial list

1 {R}

2 Press {^} or {V} to select the desired

number. i {>}

3 “Erase” i {>}

4 “Yes” i {>} i {ih}

Other features

Mute

While mute is turned on, you will be able to

hear the other party, but the other party will

not be able to hear you.

To mute your voice, press {C/T}.

L To return to the conversation, press

{C/T} again.

{R} button (to use the recall feature)

{R} is used to access optional telephone

services. Contact your service

provider/telephone company for details.

Note:

L If your unit is connected to a PBX (private

branch exchange), pressing {R} can allow

you to access certain features of your host

PBX such as transferring an extension

call. Consult your PBX dealer for details.

L You can change the recall time (page 21).

Pause button (for PBX/long distance

service users)

A pause is sometimes required when

making calls using a PBX or long distance

service.

Example: If you have to dial {0} before

dialling outside numbers manually, you will

probably need to pause after dialling {0}

until you hear a dial tone.

1 {0} i {R}

2 Dial the phone number. i {C} / {s}

Note:

L A 3 second pause is inserted each time

{R} is pressed. Press repeatedly to

insert longer pauses.

TG7150-7170FX(e).book Page 14 Wednesday, January 10, 2007 3:32 PM

Making/Answering Calls

15

Temporary tone dialling (for rotary or

pulse service users)

You can temporarily switch the dialling mode

to tone when you need to access touch tone

services (e.g., telephone banking services).

1 Make a call.

2 Press {*} when prompted to enter your

code or PIN, then press the appropriate

dial keys.

Note:

L The dialling mode will return to pulse

when you hang up.

Answering calls

1 Lift the handset and press {C} or {s}

when the unit rings.

L You can also answer a call by pressing

any dial key from {0} to {9}, {*}, {#},

or {INT}. (Any key answer feature)

2 When finished talking, press {ih} or

place the handset on the base unit.

Auto talk feature

You can answer calls simply by lifting the

handset off the base unit. You do not need to

press {C}. To turn this feature on, see

page 18.

To adjust the handset ringer volume

when receiving a call

Press {^} or {V} .

Handset locator

Using this feature, you can locate the

handset if it has been misplaced.

1 Press {x} on the base unit.

2 To stop paging, press {x} on the base

unit or press {ih} on the handset.

TG7150-7170FX(e).book Page 15 Wednesday, January 10, 2007 3:32 PM

Phonebook

16

Handset phonebook

The handset phonebook allows you to make

calls without having to dial manually. You

can add 50 names and phone numbers to

the handset phonebook.

Adding entries to the handset

phonebook

1

{k} i {j/OK}

2 “New Entry” i {>}

3 Enter the party’s name (16 characters

max.; page 28). i {j/OK}

4 Enter the party’s phone number (24

digits max.). i {j/OK}

5 “Save” i {>} i {ih}

Note:

L Step 1 variation:

{j/OK} i Press {^} or {V} to select

“Ph.Book Setup”. i {>}

Finding and calling a handset

phonebook entry

Handset phonebook entries can be

searched for by first character or by scrolling

through all handset phonebook entries.

When you have found the desired entry,

press {C}.

Scrolling through all entries

1 {k}

2 Press {^} or {V} to display the desired

entry.

Searching by first character (index

search)

1 {k}

2 Press the dial key ({0} to {9}) which

contains the character you are

searching for (page 28).

L Press the same dial key repeatedly to

display the first entry corresponding to

each letter located on that dial key.

L If there is no entry corresponding to

the letter you selected, the next entry

will be displayed.

L To change the character entry mode:

{R} i Select the character entry

mode. i {>}

3 Press {^} or {V} to scroll through the

phonebook if necessary.

Editing entries in the handset

phonebook

Changing a name, phone number

1 Find the desired entry (page 16). i

{j/OK}

2 “Edit” i {>}

3 Edit the name if necessary (16

characters max.; page 28). i

{j/OK}

4 Edit the phone number if necessary (24

digits max.). i {j/OK}

5 “Save” i {>} i {ih}

Erasing entries from the handset

phonebook

Erasing an entry

1 Find the desired entry (page 16). i

{j/OK}

2 “Erase” i {>}

3 “Yes” i {>} i {ih}

Erasing all entries

1 {k} i {j/OK}

2 “Erase All” i {>}

3 “Yes” i {>}

4 “Yes” i {>} i {ih}

TG7150-7170FX(e).book Page 16 Wednesday, January 10, 2007 3:32 PM

Phonebook

17

Chain dial

This feature allows you to dial phone

numbers in the handset phonebook while

you are on a call. This feature can be used,

for example, to dial a calling card access

number or bank account PIN that you have

stored in the handset phonebook, without

having to dial manually.

1 While on a call, press {k}.

2 Press {^} or {V} to select the desired

entry.

L To search by first character (index

search), see page 16.

3 Press {>} to dial the number.

TG7150-7170FX(e).book Page 17 Wednesday, January 10, 2007 3:32 PM

Handset Settings

18

Handset settings

L When customising the handset, the current item or setting is indicated by >.

To customise the handset:

1 {j/OK}

2 Press {^} or {V} to select “Handset Setup”. i {>}

3 Press {^} or {V} to select the desired item in the handset settings menu. i {>}

4 Press {^} or {V} to select the desired item in the sub-menu. i {>}

L In some cases, you may need to select from a second sub-menu. i {>}

5 Press {^} or {V} to select the desired setting then press {>} or follow the instruction in the

rightmost column of the chart.

L To exit the operation, press {ih}.

Handset settings

menu

Sub-menu Sub-menu 2 Feature (default setting)

Time Settings Set Date &

Time

— Date and time: page 12

Alarm — Set the alarm: page 20

Ringer Setup Ringer Volume — Handset ringer volume

(Maximum)

*1

Ext. Ringtone — Ringtones for outside calls

(“Ringtone 1”)

*2*3

Int. Ringtone — Ringtones for intercom

calls

(“Ringtone 3”)

*3

Display Setup Standby

Display

— Standby mode display

(“Off”)

*4

Select

Language

— Display language

(“English”): page 11

Contrast — Display contrast (Level 3)

Registration Register H.set — page 24

Other Options Keytones — Keytones on/off (“On”)

Auto Talk — Auto talk on/off (“Off”)

*5

Voice Announce Volume Voice announce volume

(“Middle”): page 13

Select

Language

Voice announce language

(“English”): page 13

TG7150-7170FX(e).book Page 18 Wednesday, January 10, 2007 3:32 PM

Handset Settings

19

*1 When the ringer is turned off, the handset will ring:

– at the minimum level for alarm

– at the minimum level for intercom calls

– at the maximum level for paging

*2 If you select one of the melody ringtones, the ringtone will continue to sound for several

seconds if the caller hangs up before you answer. You may hear a dial tone or no one

on the line when you answer a call.

Vision Inc.

*4 If “Off” is selected, only current date and time are displayed.

If “Handset Number” is selected and the current handset number is 2, “[2]” is

displayed.

*5 Auto talk feature allows you to answer calls simply by lifting the handset off the base

unit. You do not need to press {C}.

TG7150-7170FX(e).book Page 19 Wednesday, January 10, 2007 3:32 PM

Handset Settings

20

Time settings

Alarm

An alarm will sound for 3 minutes at the set

time once or daily. Set the date and time

beforehand (page 12).

1 {j/OK} i “Handset Setup” i

{>}

2 “Time Settings” i {>}

3 “Alarm” i Press {>} 2 times.

4 Select an alarm mode. i {>}

5 Enter the desired hour and minute. i

{j/OK}

6 Select the desired ringtone. i {>}

7 “Save” i {>} i {ih}

Note:

L To stop the alarm, press any dial key.

L When in talk or intercom mode, the alarm

will not sound until the call has ended.

L If you select “Once”, the setting will

change to “Off” after the alarm sounds.

Off Turns alarm off. Press

{>} again, then press

{ih} to finish.

Once The alarm sounds once

at the set time. Enter the

desired day and month.

Daily An alarm sounds daily at

the set time.

TG7150-7170FX(e).book Page 20 Wednesday, January 10, 2007 3:32 PM

Sayfa yükleniyor ...

Panasonic KXTG7150FX Kullanma talimatları

Bu kılavuz için de uygundur

Panasonic KXTG7150FX Kullanma talimatları

Diğer dillerde

İlgili Makaleler

Diğer Belgeler